Config air-lap1041n-e-k9 with cisco 5500 (5508) series wireless controller. how to?
Hi!
I try to configure a Cisco 5508 Wireless controller and 25 Air-lap1041 to use as VoIP and data. I read documents, manuals, etc, but the AP doesn't charge the configuration, or not conect with the Wireless Controller, why? No Radius server present, only WPA security.howto, please...
I try to put a static ip in the LAP, with lwapp or capwap command, (LWAPP/CAPWAP ap ip address direccion mascara) and the AP returns "You should configure Domain and Name Server from controller CLI/GUI." and i can't change the name of the AP (Command is disabled).
Log from AP:
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x00000184
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialize
PCIEx: initialization done
flashfs[0]: 6 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 2369024
flashfs[0]: Bytes available: 30016000
flashfs[0]: flashfs fsck took 21 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 44:2b:03:dc:09:25
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"...###########################
File "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x4000
executing...
enet halted
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
flashfs[1]: 6 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32126976
flashfs[1]: Bytes used: 2369024
flashfs[1]: Bytes available: 29757952
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 1 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.
Ethernet speed is 1000 Mb - FULL duplex
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1041N-E-K9 (PowerPC405ex) processor (revision B0) with 98294K/32
768K bytes of memory.
Processor board ID FCZ1611W414
PowerPC405ex CPU at 333Mhz, revision number 0x147E
Last reset from reload
LWAPP image version 7.0.94.21
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:2B:03:DC:09:25
Part Number : 73-14034-04
PCA Assembly Number : 800-34273-05
PCA Revision Number : A0
PCB Serial Number : FOC16075VZ3
Top Assembly Part Number : 800-34284-03
Top Assembly Serial Number : FCZ1611W414
Top Revision Number : A0
Product/Model Number : AIR-LAP1041N-E-K9
% Please define a domain-name first.
Press RETURN to get started!
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:09.574: *** CRASH_LOG = YES
Base Ethernet MAC address: 44:2B:03:DC:09:25
*Mar 1 00:00:09.838: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log
(contains, 1024 messages)
*Mar 1 00:00:11.848: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:11.892: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
*Mar 1 00:08:16.954: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
logging facility kern
^
% Invalid input detected at '^' marker.
*Mar 1 00:08:28.047: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:08:28.049: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:09:08.282: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASS
IC_NO_INJECTOR_CONFIGURED AIR-CT5508-K9 (c464.138f.9345)
*Mar 1 00:09:08.282: -Verify the required power-injector is installed on this
port: AIR-CT5508-K9(Gig 0/0/2).
*Mar 1 00:09:08.282: -If a power-injector is installed, issue the command:"pow
er inline negotiation injector installed"
*Mar 1 00:12:19.976: %CAPWAP-5-STATIC_TO_DHCP_IP: Could not discover WLC using
static IP. Forcing AP to use DHCP.
*Mar 1 00:12:29.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:39.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:49.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:59.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:09.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
Not in Bound state.
*Mar 1 00:13:19.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:19.993: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP
. Renewing DHCP IP.
logs from wireless controller:
(Cisco Controller) >show interface summary
Interface Name Port Vlan Id IP Address Type Ap Mgr Gu
est
ap-manager 2 untagged 209.165.200.231 Dynamic Yes No
management 1 untagged 209.165.200.230 Static Yes No
service-port N/A N/A 192.168.1.157 Static No No
virtual N/A N/A 1.1.1.1 Static No No
(Cisco Controller) >
i conect with service-port ok and the management port works, i think.
AP442b.03dc.0925>ping 209.165.200.230
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.200.230, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
AP442b.03dc.0925>
Help, please!
i write in spanish:
Hola:
Tengo que configurar un cisco 5508 wireless controller con 25 air-lap1041n, para usarlo como acceso de datos y voz. ¿Cómo lo hago? He leído manuales, y seguido las instrucciones, pero el punto de acceso parace que no es capaz de cargar el perfil. No hay servidor radius, solo la configuración de una clave wpa. Alguién me puede indicar pasos, Gracias
Hi!
I buy a gigabit switch. I connect the service-port to gigabit switch, and laptop to gigabit switch. I used 192.168.1.x ip address (192.168.1.157 to service-port and 192.168.1.233 to wired port on laptop, well, the laptop has two ip adress, 192.168.1.233 and 209.165.200.2, and the laptop works ok. Ping to 209.165.200.230 -ip address of management interface- and ping to 209.165.200.203 -ip address for AP, is assigned by DHCP of WLC. And i connect the ap to gigabit switch, and the wlc assigns well an ip direction.
I post the run-config and sysinfo log. The gigabit switch is tp-link model tl-sg1005d, no configuration.
Before the logs, I see this message from AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Hola:
He comprado un switch gigabit. Conecto el service-port al switch gigabit y el portátil también (por cable). Uso como direcciones ip el rango 192.168.1.x (192.168.1.157 asignado al service-port y 192, 168.1.233 al portátil, bueno, el portátil tiene dos direcciones, la dicha anteriormente y la 209.165.200.2) El portátil funciona bien, hace ping al 209.165.200.230 - la ip de la management interface, y a 209.165.200.203 - ip asignada al AP por el DHCP del WLC. He conectado el AP al swtich gigabit, y el dhcp del wlc asigna correctamente una dirección ip.
Añado a continuación los resultados de los comandos "show run-config" y "show sysinfo". El switch es un TP-LINK modelo TL-S1005D, sin necesidad de configuración.
Antes de mostrar los resultados de los comandos, he visto el siguiente mensaje en el log del AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Un saludo
Antonio R.
(Cisco Controller) >show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco Wireless Controller"
PID: AIR-CT5508-K9, VID: V02, SN: FCW1608L05X
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 17 mins 45 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Network Information
RF-Network Name............................. hosp
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or to abort
AP Summary
Number of APs.................................... 0
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Location
Site Name........................................ default-group
Site Description.................................
WLAN ID Interface Network Admission Control
1 management Disabled
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority GroupName
Press Enter to continue or to abort
AP Config
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Airewave Director Configuration
Press Enter to continue or to abort
802.11a Configuration
802.11a Network.................................. Disabled
11nSupport....................................... Enabled
802.11a Low Band........................... Enabled
802.11a Mid Band........................... Enabled
802.11a High Band.......................... Enabled
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
MCS 5........................................ Supported
MCS 6........................................ Supported
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC:
Voice AC - Admission control (ACM)............ Disabled
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Video AC:
Video AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
Video max RF bandwidth........................ Infinite
Video reserved roaming bandwidth.............. 0
Press Enter to continue or to abort
802.11a Advanced Configuration
Press Enter to continue or to abort
802.11a Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
TxPower Update Logging......................... Off
Default 802.11a AP performance profiles
802.11a Global Interference threshold.......... 10 %
802.11a Global noise threshold................. -70 dBm
802.11a Global RF utilization threshold........ 80 %
802.11a Global throughput threshold............ 1000000 bps
802.11a Global clients threshold............... 12 clients
Default 802.11a AP monitoring
802.11a Monitor Mode........................... enable
802.11a Monitor Mode for Mesh AP Backhaul...... disable
802.11a Monitor Channels....................... Country channels
802.11a AP Coverage Interval................... 180 seconds
802.11a AP Load Interval....................... 60 seconds
802.11a AP Noise Interval...................... 180 seconds
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
802.11a AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
Coverage Hole Detection
802.11a Coverage Hole Detection Mode........... Enabled
802.11a Coverage Voice Packet Count............ 100 packets
802.11a Coverage Voice Packet Percentage....... 50%
802.11a Coverage Voice RSSI Threshold.......... -80 dBm
802.11a Coverage Data Packet Count............. 50 packets
802.11a Coverage Data Packet Percentage........ 50%
802.11a Coverage Data RSSI Threshold........... -80 dBm
802.11a Global coverage exception level........ 25 %
802.11a Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
--More or (q)uit current module or to abort
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
DCA Sensitivity Level.......................... STARTUP (5 dB)
DCA 802.11n Channel Width...................... 20 MHz
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11a 5 GHz Auto-RF Channel List
Allowed Channel List......................... 36,40,44,48,52,56,60,64
Unused Channel List.......................... 100,104,108,112,116,120,124,
128,132,136,140
DCA Outdoor AP option.......................... Disabled
Radio RF Grouping
802.11a Group Mode............................. AUTO
--More or (q)uit current module or to abort
802.11a Group Update Interval.................. 600 seconds
802.11a Group Leader........................... c4:64:13:8f:93:40
802.11a Group Member......................... c4:64:13:8f:93:40
802.11a Last Run............................... 75 seconds ago
802.11b Configuration
802.11b Network.................................. Enabled
11gSupport....................................... Enabled
11nSupport....................................... Enabled
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Mandatory
802.11b/g 2M Rate............................ Mandatory
802.11b/g 5.5M Rate.......................... Mandatory
802.11b/g 11M Rate........................... Mandatory
802.11g 6M Rate.............................. Supported
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Supported
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
--More or (q)uit current module or to abort
MCS 5........................................ Supported
MCS 6........................................ Supported
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mode................................. Disabled
--More or (q)uit current module or to abort
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 1
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Call Admission Limit ........................... 105
G711 CU Quantum ................................. 15
ED Threshold..................................... -50
Fragmentation Threshold.......................... 2346
PBCC mandatory................................... Disabled
RTS Threshold.................................... 2347
Short Preamble mandatory......................... Enabled
Short Retry Limit................................ 7
Legacy Tx Beamforming setting.................... Enabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
Faster Carrier Tracking Loop..................... Disabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ 50
Video reserved roaming bandwidth.............. 0
802.11b Advanced Configuration
Press Enter to continue or to abort
802.11b Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
Transmit Power Update Logging.................. Off
Default 802.11b AP performance profiles
802.11b Global Interference threshold.......... 10 %
802.11b Global noise threshold................. -70 dBm
802.11b Global RF utilization threshold........ 80 %
802.11b Global throughput threshold............ 1000000 bps
802.11b Global clients threshold............... 12 clients
Default 802.11b AP monitoring
802.11b Monitor Mode........................... enable
802.11b Monitor Channels....................... Country channels
802.11b AP Coverage Interval................... 180 seconds
802.11b AP Load Interval....................... 60 seconds
802.11b AP Noise Interval...................... 180 seconds
802.11b AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
Coverage Hole Detection
802.11b Coverage Hole Detection Mode........... Enabled
802.11b Coverage Voice Packet Count............ 100 packets
802.11b Coverage Voice Packet Percentage....... 50%
802.11b Coverage Voice RSSI Threshold.......... -80 dBm
802.11b Coverage Data Packet Count............. 50 packets
802.11b Coverage Data Packet Percentage........ 50%
802.11b Coverage Data RSSI Threshold........... -80 dBm
802.11b Global coverage exception level........ 25 %
802.11b Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
DCA Sensitivity Level: ...................... STARTUP (5 dB)
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11b Auto-RF Allowed Channel List........... 1,6,11
Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10,12,13
Radio RF Grouping
802.11b Group Mode............................. AUTO
802.11b Group Update Interval.................. 600 seconds
802.11b Group Leader........................... c4:64:13:8f:93:40
802.11b Group Member......................... c4:64:13:8f:93:40
802.11b Last Run............................... 213 seconds ago
Mobility Configuration
Symmetric Mobility Tunneling (current) .......... Enabled
Symmetric Mobility Tunneling (after reboot) ..... Enabled
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... hosp
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0x97e2
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 1
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address IP Address Group Name Multicast
IP Status
c4:64:13:8f:93:40 209.165.200.230 hosp 0.0.0.0
Up
Advanced Configuration
Probe request filtering.......................... Enabled
Probes fwd to controller per client per radio.... 0
Probe request rate-limiting interval............. 500 msec
EAP-Identity-Request Timeout (seconds)........... 30
EAP-Identity-Request Max Retries................. 2
EAP Key-Index for Dynamic WEP.................... 0
EAP Max-Login Ignore Identity Response........... enable
EAP-Request Timeout (seconds).................... 30
EAP-Request Max Retries.......................... 2
EAPOL-Key Timeout (milliseconds)................. 1000
EAPOL-Key Max Retries............................ 2
dot11-padding.................................... Disabled
Authentication Response Timeout (seconds)........ 10
Rogue Entry Timeout (seconds).................... 1200
AP Heart Beat Timeout (seconds).................. 30
AP Discovery Timeout (seconds)................... 10
AP Local mode Fast Heartbeat (seconds)........... disable
AP Hreap mode Fast Heartbeat (seconds)........... disable
AP Primary Discovery Timeout (seconds)........... 120
AP Primed Join Timeout (seconds)................. 0
Packet Forwarding watchdog timer (seconds)....... 240 (enable)
Location Configuration
RFID Tag data Collection......................... Enabled
RFID timeout.................................... 1200 seconds
RFID mobility.................................... Oui:00:14:7e : Vendor:pango S
tate:Disabled
Interface Configuration
Interface Name................................... management
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 209.165.200.230
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 209.165.200.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 192.168.1.1
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 209.165.200.230
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
Interface Name................................... service-port
MAC Address...................................... c4:64:13:8f:93:41
IP Address....................................... 192.168.1.157
IP Netmask....................................... 255.255.255.0
DHCP Option 82................................... Disabled
DHCP Protocol.................................... Disabled
AP Manager....................................... No
Guest Interface.................................. No
Interface Name................................... virtual
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 1.1.1.1
DHCP Option 82................................... Disabled
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
WLAN Configuration
WLAN Identifier.................................. 1
Profile Name..................................... HOSP3C
Network Name (SSID).............................. HOSP3C
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
NAC-State...................................... Disabled
Quarantine VLAN................................ 0
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
WLAN ACL......................................... unconfigured
DHCP Server...................................... 209.165.200.230
DHCP Address Assignment Required................. Enabled
Quality of Service............................... Platinum (voice)
Scan Defer Priority.............................. 5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... 802.11b and 802.11g only
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Disabled
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT(802.11r)............................. Disabled
FT-PSK(802.11r)......................... Disabled
FT Reassociation Timeout......................... 20
FT Over-The-Air mode............................. Enabled
FT Over-The-Ds mode.............................. Enabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
H-REAP Local Switching........................ Disabled
H-REAP Learn IP Address....................... Enabled
Infrastructure MFP protection................. Enabled
Client MFP.................................... Optional
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Band Select...................................... Enabled
Load Balancing................................... Enabled
Mobility Anchor List
WLAN ID IP Address Status
Press Enter to continue or to abort
Press Enter to continue or to abort
ACL Configuration
Press Enter to continue or to abort
CPU ACL Configuration
CPU Acl Name................................ NOT CONFIGURED
Wireless Traffic............................ Disabled
Wired Traffic............................... Disabled
RADIUS Configuration
Vendor Id Backward Compatibility................. Disabled
Call Station Id Case............................. lower
Call Station Id Type............................. IP Address
Aggressive Failover.............................. Enabled
Keywrap.......................................... Disabled
Fallback Test:
Test Mode.................................... Off
Probe User Name.............................. cisco-probe
Interval (in seconds)........................ 300
MAC Delimiter for Authentication Messages........ hyphen
MAC Delimiter for Accounting Messages............ hyphen
Authentication Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
Accounting Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
--More or (q)uit current module or to abort
TACACS Configuration
Authentication Servers
Idx Server Address Port State Tout
Authorization Servers
Idx Server Address Port State Tout
Accounting Servers
Idx Server Address Port State Tout
LDAP Configuration
Press Enter to continue or to abort
Local EAP Configuration
User credentials database search order:
Primary ..................................... Local DB
Timer:
Active timeout .............................. 300
Configured EAP profiles:
EAP Method configuration:
EAP-FAST:
Server key ................................
TTL for the PAC ........................... 10
Anonymous provision allowed ............... Yes
Authority ID .............................. 436973636f00000000000000000000
00
Authority Information ..................... Cisco A-ID
Press Enter to continue or to abort
HREAP Group Summary
HREAP Group Summary: Count: 0
Group Name # Aps
Press Enter to continue or to abort
HREAP Group Detail
Press Enter to continue or to abort
Route Info
Number of Routes................................. 0
Destination Network Netmask Gateway
Press Enter to continue or to abort
Qos Queue Length Info
Platinum queue length............................ 100
Gold queue length................................ 75
Silver queue length.............................. 50
Bronze queue length.............................. 25
Press Enter to continue or to abort
Mac Filter Info
Press Enter to continue or to abort
Authorization List
Authorize MIC APs against AAA ................... disabled
Authorize LSC APs against Auth-List ............. disabled
Allow APs with MIC - Manufactured Installed C.... disabled
Allow APs with SSC - Self-Signed Certificate..... disabled
Allow APs with LSC - Locally Significant Cert.... disabled
Load Balancing Info
Aggressive Load Balancing........................ Disabled
Aggressive Load Balancing Window................. 5 clients
Aggressive Load Balancing Denial Count........... 3
Statistics
Total Denied Count............................... 0 clients
Total Denial Sent................................ 0 messages
Exceeded Denial Max Limit Count.................. 0 times
None 5G Candidate Count.......................... 0 times
None 2.4G Candidate Count........................ 0 times
Press Enter to continue or to abort
Dhcp Scope Info
Scope: PUNTOSAP
Enabled.......................................... Yes
Lease Time....................................... 86400 (1 day )
Pool Start....................................... 209.165.200.201
Pool End......................................... 209.165.200.229
Network.......................................... 209.165.200.0
Netmask.......................................... 255.255.255.0
Default Routers.................................. 0.0.0.0 0.0.0.0 0.0.0.0
DNS Domain.......................................
DNS.............................................. 0.0.0.0 0.0.0.0 0.0.0.0
Netbios Name Servers............................. 0.0.0.0 0.0.0.0 0.0.0.0
Press Enter to continue or to abort
Exclusion List ConfigurationUnable to retrieve exclusion-list entry
Press Enter to continue or to abort
CDP Configuration
Press Enter to continue or to abort
Country Channels Configuration
Configured Country............................. ES - Spain
KEY: * = Channel is legal in this country and may be configured manually.
A = Channel is the Auto-RF default in this country.
. = Channel is not legal in this country.
C = Channel has been configured for use by Auto-RF.
x = Channel is available to be configured for use by Auto-RF.
(-,-) = (indoor, outdoor) regulatory doamin allowed by this country.
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11bg :
Channels : 1 1 1 1 1
: 1 2 3 4 5 6 7 8 9 0 1 2 3 4
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): A * * * * A * * * * A * * .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11a : 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Channels : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
: 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): . A . A . A . A A A A A * * * * * * * * * * * . . . . .
Press Enter to continue or to abort
WPS Configuration Summary
Auto-Immune
Auto-Immune.................................... Disabled
Client Exclusion Policy
Excessive 802.11-association failures.......... Enabled
Excessive 802.11-authentication failures....... Enabled
Excessive 802.1x-authentication................ Enabled
IP-theft....................................... Enabled
Excessive Web authentication failure........... Enabled
Signature Policy
Signature Processing........................... Enabled
Press Enter to continue or to abort
Custom Web Configuration
Radius Authentication Method..................... PAP
Cisco Logo....................................... Enabled
CustomLogo....................................... None
Custom Title..................................... None
Custom Message................................... None
Custom Redirect URL.............................. None
Web Authentication Type.......................... Internal Default
External Web Authentication URL.................. None
Configuration Per Profile:
Rogue AP Configuration
Rogue Location Discovery Protocol................ Disabled
Rogue on wire Auto-Contain....................... Disabled
Rogue using our SSID Auto-Contain................ Disabled
Valid client on rogue AP Auto-Contain............ Disabled
Rogue AP timeout................................. 1200
MAC Address Classification # APs # Clients Last Heard
Adhoc Rogue Configuration
Detect and report Ad-Hoc Networks................ Enabled
Auto-Contain Ad-Hoc Networks..................... Disabled
Client MAC Address Adhoc BSSID State # APs Last Heard
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
--More-- or (q)uit
MAC Address State # APs Last Heard
Ignore List Configuration
MAC Address
Rogue Rule Configuration
Priority Rule Name State Type Match Hit Count
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 41 mins 2 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +39 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
(Cisco Controller) >
The AP log
AP442b.03dc.0925>
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Selected MWAR 'CISCO-CAPWAP-CONTROLLER
'(index 0).
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Go join a capwap controller
logging facility kern
^
% Invalid input detected at '^' marker.
logging facility kern
^
% Invalid input detected at '^' marker.
*Apr 19 23:10:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:19.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Apr 19 23:10:20.200: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:20.201: %CAPWAP-5-SENDJOIN: sending Join Request to 209.165.200.23
0
*Apr 19 23:10:20.201: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
*Apr 19 23:10:20.354: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Apr 19 23:10:20.355: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 209
.165.200.230:5246
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.412: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established
Similar Messages
-
Error in Cisco 2500 series Wireless Controller
I have this error in Cisco 2500 series Wireless Controller
The AP type Cisco AIR-CAP35021-A-K9
I cann't connect the client to AP when i try to connect i get this error on Cisco 2500 series Wireless Controller But the AP get ip .
Please can any on help me .
Client Excluded: MACAddress:Base Radio MAC : Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode:Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12142556/cisco-2500-series-wireless-controller -
Hello,good day problem with Cisco aironet 1040 series acces point
Hello good day to all, how to configure cisco aironet 1040 series using web configuration attaching through patch cord without using the console.
if possible please send me step by step instruction, any help is gladly appreciated.
thank you in advance, More power
melhelo good day sir,
this is the first time i configure this device i am using Cisco aironet 1040 for our wireless using POE for power, and using cisco catalyst 2960 as switch
i jack the patch cord in and its goes on colored green,
the thing is how i can configure the aironet 1040 sir?
waiting for a step by step instruction,
thank you in advance
mel -
Cisco Aironet 1100 series wireless access point software update!
Hi,
I have a wireless network using 2 cisco aironet 1100 series access points.
From time to time I have problems with connecting a device (Laptop,PC,)to the wireless network.There are onther wireless netwotk that operate around and might be using the same channel.Someone else created the wireless network and I do not know how to access it now to check the configurations on change something.
I cannot conncet my iPhone to the network and I beleive that a software update might solve the problem but I do not know how to do it and where to download it from.
1. How can I update the software and where from?
2.How can I ensure that thare are no interferences and conflicts?
3.How can I ensure that no onther wireless network around is using the same channel?
Thank you in advance.Sounds good to me. Are you having problems?
Please remeber to rate all replies -
Want to hear about vCAC when used with Cisco UCS Director... How are you seeing this done?
I have a client that has both VMware vCloud Automation Center, and Cisco UCS Director.
They wish to constuct a net-new (Greenfield) data center and are hearing from both VMware and Cisco.
I have researched, and found little regarding the merger of the two.
I realize that very likely vCAC is teh "main" management platform, while Cisco UCSD will handle the more "physical hardware" tasks.
REST API's will be leveraged as well.
What have you seen written and done in this space when using BOTH?
Please send me any thoughts or links to relevant data.
I am having a hard time locating good data so that I an advise the client in a good way.Bahi,
just to illustrate what mess this is, I tested for you on Leopard (10.5) and Snow Leopard (10.6) using the same wide gamut monitor. Here are two screenshots from that experiment. I converted the screenshots from my display profile to sRGB to show you what I see and scaled down 50% (this is a 30" behemoth). First Leopard.
You see they are all the same, but different from the sRGB export you provided. The GB sticker is too blue and the tint on the car is wrong. I doubt anybody but a photographer would notice though.
Next is Snow Leopard:
Here the 320 pixel, the 480 pixel and the 960 pixel image are different from the 720 pixel, the 720p and the 1080p ones. Neither is strictly correct as they are all different from the sRGB display. This is consistent with their being no real color management, just gamma corrections and color space transforms (video is usually not stored as RGB but as YUV, necessitating a transform for display). Annoying, but not much you can do about it.
Just doing some quick googling I came across many mentions of issues such as this. It clearly is just a big mess. -
Cisco Aironet 1300 Series wireless birdge problem
Hi,
first one, i'm sorry for my english.
I have a very big problem with the bridge. I can't configure the nonRoot bridge. It's not possible for me to turn on the radio. The software and hardware are always disable...
The SSID management is configured with the same SSID.
For the test, there isn't encryption.
thanks a lot for your help
G.VincentHi,
Thank you for your answer.
The root birdge is a 1310G-E-K9-R
Tne non root bridge is a 1310G-E-K9-R
To configure the bridge, I have followed the cisco documentation.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008058f53e.shtml
The root configuration:
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
dot11 activity-timeout bridge default 1
dot11 ssid martinshotels
guest-mode
infrastructure-ssid
username Cisco password xxx
username administrator privilege 15 password xxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid martinshotels
station-role root bridge
distance 1
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.0.250 255.255.255.0
no ip route-cache
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
end
The non root configuration :
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname apNonRoot
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
dot11 activity-timeout bridge default 1
dot11 ssid martinshotels
guest-mode
infrastructure-ssid
username Cisco password xxx
username administrator privilege 15 password xxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid martinshotels
station-role non-root bridge
mobile station scan 2417
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.0.251 255.255.255.0
no ip route-cache
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
end
Thanks a lot for your help -
Azure multiple site-to-site VPNs (dynamic gateway) with Cisco ASA devices
Hello
I've been experimenting with moving certain on-premise servers to Azure however they would need a site-to-site VPN link to our many branch sites e.g. monitoring of nodes.
The documentation says I need to configure a dynamic gateway to have multiple site-to-site VPNs. This is not a problem for our typical Cisco ISR's. However three of our key sites use Cisco ASA devices which are listed as 'Not Compatible' with dynamic routing.
So I am stuck...
What options are available to me? Is there any sort of tweak-configuration to make a Cisco ASA work with Azure and dynamic routing?
I was hoping Azure's VPN solution would be very flexible.
ThanksHello RTF_Admin,
1. Which is the Series of CISCO ASA device you are using?
Thank you for your interest in Windows Azure. The Dynamic routing is not supported for the Cisco ASA family of devices.
Unfortunately, a dynamic routing VPN gateway is required for Multi-Site VPN, VNet to VNet, and Point-to-Site.
However, you should be able to setup a site-to-site VPN with Cisco ASA 5505 series security appliance as demonstrated in this blog:
Step-By-Step: Create a Site-to-Site VPN between your network and Azure
http://blogs.technet.com/b/canitpro/archive/2013/10/09/step-by-step-create-a-site-to-site-vpn-between-your-network-and-azure.aspx
You can refer to this article for Cisco ASA templates for Static routing:
http://msdn.microsoft.com/en-us/library/azure/dn133793.aspx
If your requirement is only for Multi-Site VPN then there is no option but to upgrade the device as Multisite VPN requires dyanmic routing and unfortunately there is no tweak or workaround due to hardware compatibility issue.
I hope that this information is helpful
Thanks,
Syed Irfan Hussain -
Azure Site to Site VPN with Cisco ASA 5505
I have got Cisco ASA 5505 device (version 9.0(2)). And i cannot connect S2S with azure (azure network alway in "connecting" state). In my cisco log:
IP = 104.40.182.93, Keep-alives configured on but peer does not support keep-alives (type = None)
Group = 104.40.182.93, IP = 104.40.182.93, QM FSM error (P2 struct &0xcaaa2a38, mess id 0x1)!
Group = 104.40.182.93, IP = 104.40.182.93, Removing peer from correlator table failed, no match!
Group = 104.40.182.93, IP = 104.40.182.93,Overriding Initiator's IPSec rekeying duration from 102400000 to 4608000 Kbs
Group = 104.40.182.93, IP = 104.40.182.93, PHASE 1 COMPLETED
I have done all cisco s2s congiguration over standard wizard cos seems your script for 8.x version of asa only?
(Does azure support 9.x version of asa?)
How can i fix it?Hi,
As of now, we do not have any scripts for Cisco ASA 9x series.
Thank you for your interest in Windows Azure. The Dynamic routing is not supported for the Cisco ASA family of devices.
Unfortunately, a dynamic routing VPN gateway is required for Multi-Site VPN, VNet to VNet, and Point-to-Site.
However, you should be able to setup a site-to-site VPN with Cisco ASA 5505 series security appliance as
demonstrated in this blog:
Step-By-Step: Create a Site-to-Site VPN between your network and Azure
http://blogs.technet.com/b/canitpro/archive/2013/10/09/step-by-step-create-a-site-to-site-vpn-between-your-network-and-azure.aspx
You can refer to this article for Cisco ASA templates for Static routing:
http://msdn.microsoft.com/en-us/library/azure/dn133793.aspx
Did you download the VPN configuration file from the dashboard and copy the content of the configuration
file to the Command Line Interface of the Cisco ASDM application? It seems that there is no specified IP address in the access list part and maybe that is why the states message appeared.
According to the
Cisco ASA template, it should be similar to this:
access-list <RP_AccessList>
extended permit ip object-group
<RP_OnPremiseNetwork> object-group <RP_AzureNetwork>
nat (inside,outside) source static <RP_OnPremiseNetwork>
<RP_OnPremiseNetwork> destination static <RP_AzureNetwork>
<RP_AzureNetwork>
Based on my experience, to establish
IPSEC tunnel, you need to allow the ESP protocol and UDP Port 500. Please make sure that the
VPN device cannot be located behind a NAT. Besides, since Cisco ASA templates are not
compatible for dynamic routing, please make sure that you chose the static routing.
Since you configure the VPN device yourself, it's important that you would be familiar with the device and its configuration settings.
Hope this helps you.
Girish Prajwal -
Cisco Aironet 3502i and Virtual Wireless Controller- Question
Hello everyone,
As soon, I purchased two Cisco 3502i and Cisco 1142 however, two issue are that I don't have controller and smartnet. As my purpose, it using for Home Use but house with 2,500 Sq ft with two floor and new 24x24ft garage with two floor. I put two Cisco 3502i for garage and one cisco 1142 in house on second floor. Separated for multi media, gaming, streaming high resolution video, parts, and downloads programmings online. It will run with Cisco Catalyst Express 500 with 24 ports (4 POE) and two gigabit ports. In house, it have Dell Poweredge 2850, Cisco Catalyst Express 500 with 24 ports POE and 2 ports gigabit.
I thought to make my own developing with my first time using Wireless Controller. I wanted to try out with Virtual WLC on Dell Poweredge 2850 running ESXi 4.1.
Specs for Dell Poweredge 2850:
- 2x Intel Xeon Dual Core 3.8 GHz
- 4GB RAM (Will upgrade to 12GB soon)
- 2x 146GB and 2x 36GB SCSI
- 2x 1 Gbps built in and 4x 1 Gbps PCI-X
Developing with Untangle and pfSense to make it support with LADP and VLAN to both Cisco Express 500 using 4 gbps PCI-X. I have read the requipment list to use Virtual WLC but it seem met the requipment for my 2850. If someone offer me to get Virtual WLC and IOS from their, I accept to "borrow" it. I do go college which is Rochester Institute of Technology at New York and my major is Applied Computer Technology. I live here at Hampton Road, Virginia. Just in case if you might know about RIT. I just start to learning myself with Cisco books.
I have a question:
- Is there possible to get trial or full version of Virtual WLC?
- Is there possible to get Lightweight or Autonomous IOS for Cisco 1142 and 3502i?
- Does it supported Dell PowerEdge 2850?
- Does 3502i support Autonomous? (Not actually but I have researched around online about that it will work with 1262's IOS)
Thanks
GageAnswers in-line...
I have a question:
- Is there possible to get trial or full version of Virtual WLC?
No. You will need a SmartNet contract (or a freshly purchased device) to obtain software from cisco. Nobody will provide this to you.
- Is there possible to get Lightweight or Autonomous IOS for Cisco 1142 and 3502i?
No. You will need a SmartNet contract (or a freshly purchased device) to obtain software from cisco.
Nobody will provide this to you.
- Does it supported Dell PowerEdge 2850?
Cisco doesn't go in to great detail regarding the actual Hardware requirements of the vWLC (as far as ESX Host requirements). Primarily, making sure you are running ESX 4.x/5.x is necessary. The vWLC provisions 2Gb of RAM and 8GB of thick provisioned storage, so if your host can accomodate I don't see any reason it wouldn't work.
- Does 3502i support Autonomous? (Not actually but I have researched around online about that it will work with 1262's IOS)
Yes, with the latest versions of IOS 15.2(2)JB, full functionality in autonomous can be achieved on the 1550, 3500, and 3600 series APs
http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/15.2_2_JB.html#wp355587 -
Cisco AIR-LAP1041N-E-K9 not working with WLC 4402 version 7.0.116.0
Hi All,
appreciate your support for a problem i started facing today. i have a Cisco WLC 4402 running version 7.0.116.0 and it is working great with 25 Cisco 1252 APs. we have recieved a new 20 Cisco 1041N APs today and i installed one in our site but it doesn't work. it worked fine and loaded the image from flash and got the WLC ip address through DHCP option and started showing the below error:
*Mar 1 00:00:10.021: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:10.033: *** CRASH_LOG = YES
*Mar 1 00:00:10.333: Port 1 is not presentSecurity Core found.
Base Ethernet MAC address: C8:9C:1D:53:57:5E
*Mar 1 00:00:11.373: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:11.465: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1088 messages)
*Mar 1 00:00:11.494: status of voice_diag_test from WLC is false
*Mar 1 00:00:12.526: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:13.594: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:13.647: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 13-Apr-11 12:50 by prod_rel_team
*Mar 1 00:00:13.647: %SNMP-5-COLDSTART: SNMP agent on host APc89c.1d53.575e is undergoing a cold start
*Mar 1 00:08:59.062: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:08:59.062: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:08:59.138: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:08:59.837: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:09:00.145: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:09:09.136: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 172.16.26.81, mask 255.255.255.0, hostname APc89c.1d53.575e
*Mar 1 00:09:17.912: %PARSER-4-BADCFG: Unexpected end of configuration file.
*Mar 1 00:09:17.912: status of voice_diag_test from WLC is false
*Mar 1 00:09:17.984: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:09:19.865: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:09:19.886: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:09:20.873: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:09:20.874: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
Translating "CISCO-CAPWAP-CONTROLLER.atheertele.com"...domain server (172.16.40.240)
*Mar 1 00:09:29.029: %CAPWAP-5-DHCP_OPTION_43: Controller address 172.16.100.102 obtained through DHCP
*May 25 08:27:02.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:02.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:03.175: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:03.177: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:03.177: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:03.329: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:03.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:03.333: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:03.333: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:03.378: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:03.378: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:03.378: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:03.448: status of voice_diag_test from WLC is false
*May 25 08:27:14.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:14.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:15.185: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:15.186: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:15.186: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:15.330: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:15.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:15.334: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:15.334: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:15.379: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:15.379: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:15.379: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:15.450: status of voice_diag_test from WLC is false
*May 25 08:27:26.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:26.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:27.182: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:27.183: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:27.184: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:27.329: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:27.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:27.333: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:27.333: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:27.377: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:27.377: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:27.377: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:27.433: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*May 25 08:27:27.446: %PARSER-4-BADCFG: Unexpected end of configuration file.
*May 25 08:27:27.447: status of voice_diag_test from WLC is false
*May 25 08:27:27.448: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*May 25 08:27:27.456: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*May 25 08:27:38.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:38.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:39.183: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:39.184: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:39.184: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:39.326: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:39.329: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:39.329: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:39.330: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:39.375: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:39.375: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:39.375: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:39.446: status of voice_diag_test from WLC is false
*May 25 08:27:49.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:49.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:50.179: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:50.180: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:50.180: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:50.323: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:50.326: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:50.326: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:50.326: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:50.370: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:50.370: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:50.370: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:50.425: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*May 25 08:27:50.438: %PARSER-4-BADCFG: Unexpected end of configuration file.
i searched for the regulatory domains difference between AIR-LAP1041N-E-K9 and AIR-LAP1041N-A-K9 and didn't find any difference that may affect the operation of this AP.
just to mention that our configuration in WLC for regulatory domains is:
Configured Country Code(s) AR
Regulatory Domain 802.11a: -A
802.11bg: -A
My question is, should i only include my country in the WLC (IQ) to add the requlatry domain (-E) to solve this problem? or changing the country will affect the operation of all working APs??
Appreciate your kind support,
Wisam Q.Hi Ramon,
thank you for the reply but as shown in the below link:
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn7.0.html#wp233793
the WLC in version 7.0.116.0 supports Cisco 1040 seiries APs.
Thanks,
Wisam Q. -
Setting up site to site vpn with cisco asa 5505
I have a cisco asa 5505 that needs to be set up for site to site vpn to a cisco asa 5500. The 5505 is the remote office and the 5500 is the main office.
IP of remote office router is 71.37.178.142
IP of the main office firewall is 209.117.141.82
Can someone tell me if my config is correct, this is the first time I am setting this up and it can not be tested until I set it up at the remote office. I would rather know its correct before I go.
ciscoasa# show run
: Saved
ASA Version 7.2(4)
hostname ciscoasa
domain-name default.domain.invalid
enable password TMACBloMlcBsq1kp encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 host 209.117.141.82
access-list inside_nat0_outbound extended permit ip host 71.37.178.142 host 209.117.141.82
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group5
crypto map outside_map 1 set peer 209.117.141.82
crypto map outside_map 1 set transform-set ESP-AES-256-SHA
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
vpdn username [email protected] password ********* store-local
dhcpd auto_config outside
dhcpd address 192.168.1.2-192.168.1.129 inside
dhcpd enable inside
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:7e338fb2bf32a9ceb89560b314a5ef6c
: end
ciscoasa#
Thanks!Hi Mandy,
By using following access list define Peer IP as source and destination
access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
you are not defining the interesting traffic / subnets from both ends.
Make some number ACL 101 as you do not have to write the extended keyword then if you like as follows, or else NAME aCL will also work:
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
access-list 101 remark CCP_ACL Category=4 access-list 101 remark IPSEC Rule
!.1..source subnet(called local encryption domain) at your end 192.168.200.0
!..2.and destination subnet(called remote encryption domain)at other end 192.168.100.0 !.3..I mean you have to define what subnets you need to communicate between which are behind these firewalls
!..4...Local Subnets behind IP of the main office firewall is 209.117.141.82 say
!...at your end 192.168.200.0
!..5.Remote Subnets behind IP of remote office router is 71.37.178.142 say
!...at other end 192.168.100.0
Please use Baisc Steps as follows:
A. Configuration in your MAIN office having IP = 209.117.141.82 (follow step 1 to 6)
Step 1.
Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
Step 2.
Config ISAKMP Policy with minimum 4 parameters are to be config for
crypto isakmp policy 10
authentication pre-share ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
encryption aes-256 --->2nd parameter of ISAKMP Policy is OK
hash sha ---> 3rd parameter of ISAKMP Policy is OK
group 5 ---> 4th parameter of ISAKMP Policy is OK
lifetime 86400 ------ > this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
Step 3.
Define Preshared key or PKI which you will use with other side Peer address 71.37.178.142, either key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
Here in your case in step 2 Authentication is using PSK, looks you have not defines Password
Use following command:
crypto isakmp key 0 CISCO123 address 71.37.178.142
or , but not both
crypto isakmp key 6 CISCO123 address71.37.178.142
step 4.
Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
Here is yours one:
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
or
crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
ah-sha-hmac or ah-md5-hmac
crypto ipsec transform-set TSET1 ah-sha-hmac
or
crypto ipsec transform-set TSET1 ah-md5-hmac
Step 5.
Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
crypto map ipsec-isakmp
1. Define peer -- called WHO to set tunnel with
2. Define or call WHICH - Transform Set
3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
Like in your case it is but ipsec-isakmp keyword missing in the ;ast
crypto map outside_map 10 ipsec-isakmp
1. set peer 209.117.141.82 -----> is correct as this is your other side peer called WHO in my step
2. set transform-set TSET1 -----> is correct as this is WHICH, and only one transform set can be called
!..In you case it is correct
!...set transform-set ESP-AES-256-SHA (also correct)
3. match address outside_1_cryptomap ---->Name of the extended ACL define as WHAT to pass through this tunnel
4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
Step 6.
Now apply this one crypto MAP to your OUTSIDE interface always
interface outside
crypto map outside_map
Configure the same but just change ACL on other end in step one by reversing source and destination
and also set the peer IP of this router in other end.
So other side config should look as follows:
B. Configuration in oyur Remote PEER IP having IP = 71.37.178.142 (follow step 7 to 12)
Step 7.
Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
access-list outside_1_cryptomap extended ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255
Step 8.
Config ISAKMP Policy with minimum 4 parameters are to be config for
crypto isakmp policy 10
authentication pre-share ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
encryption aes-256 --->2nd parameter of ISAKMP Policy is OK
hash sha ---> 3rd parameter of ISAKMP Policy is OK
group 5 ---> 4th parameter of ISAKMP Policy is OK
lifetime 86400 ------ > this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
Step 9.
Define Preshared key or PKI which you will use with other side Peer address key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
Here in your case in step 8 Authentication is using PSK, looks you have not defines Password
Use following command:
crypto isakmp key 0 CISCO123 address 209.117.141.82
or , but not both
crypto isakmp key 6 CISCO123 address 209.117.141.82
step 10.
Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
Here is yours one:
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
or
crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
ah-sha-hmac or ah-md5-hmac
crypto ipsec transform-set TSET1 ah-sha-hmac
or
crypto ipsec transform-set TSET1 ah-md5-hmac
Step 11.
Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
crypto map ipsec-isakmp
1. Define peer -- called WHO to set tunnel with
2. Define or call WHICH - Transform Set, only one is permissible
3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
Like in your case it is but ipsec-isakmp keyword missing in the ;ast
crypto map outside_map 10 ipsec-isakmp
1. set peer 209.117.141.82 -----> is correct as this is your other side peer called WHO in my step
2. set transform-set TSET1 -----> is correct as this is WHICH, and only one transform set can be called
!..In you case it is correct
!...set transform-set ESP-AES-256-SHA (also correct)
3. match address outside_1_cryptomap ---->Name of the extended ACL define as WHAT to pass through this tunnel
4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
Step 12.
Now apply this one crypto MAP to your OUTSIDE interface always
interface outside
crypto map outside_map
Now initite a ping
Here is for your summary:
IPSec: Site to Site - Routers
Configuration Steps
Phase 1
Step 1: Configure Mirrored ACL/Crypto ACL for Interesting Traffic
Step 2: Configure ISAKMP Policy
Step 3: Configure ISAKMP Key
Phase 2
Step 4: Configure Transform Set
Step 5: Configure Crypto Map
Step 6: Apply Crypto Map to an Interface
To debug for Phase 1 and Phase 2. Store it in buffer without displaying logs on terminal.
Router#debug crpyto isakmp
Router#debug crpyto ipsec
Router(config)# logging buffer 7
Router(config)# logging buffer 99999
Router(config)# logging console 6
Router# clear logging
Configuration
In R1:
(config)# access-list 101 permit ipo host 10.1.1.1 host 10.1.2.1
(config)# crypto isakmp policy 10
(config-policy)# encryption 3des
(config-policy)# authentication pre-share
(config-policy)# group 2
(config-policy)# hash sha1
(config)# crypto isakmp key 0 cisco address 2.2.2.1
(config)# crypto ipsec transform-set TSET esp-3des sha-aes-hmac
(config)# crypto map CMAP 10 ipsec-isakmp
(config-crypto-map)# set peer 2.2.2.1
(config-crypto-map)# match address 101
(config-crypto-map)# set transform-set TSET
(config)# int f0/0
(config-if)# crypto map CMAP
Similarly in R2
Verification Commands
#show crypto isakmp SA
#show crypto ipsec SA
Change to Transport Mode, add the following command in Step 4:
(config-tranform-set)# mode transport
Even after doing this change, the ipsec negotiation will still be done through tunnel mode if pinged from Loopback to Loopback. To overcome this we make changes to ACL.
Change to Aggressive Mode, replace the Step 3 command with these commands in R1:
(config)# crypto isakmp peer address 2.2.2.1
(config-peer)# set aggressive-mode password cisco
(config-peer)# set aggressive-mode clien-endpoint ipv4-address 2.2.2.1
Similarly on R2.
The below process is for the negotiation using RSA-SIG (PKI) as authentication type
Debug Process:
After we debug, we can see the negotiation between the two peers. The first packet of the interesting traffic triggers the ISAKMP (Phase1) negotiation. Important messages are marked in BOLD and explanation in RED
R2(config)#do ping 10.1.1.1 so lo0 // Interesting Traffic
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
Packet sent with a source address of 2.2.2.2
Mar 2 16:18:42.939: ISAKMP:(0): SA request profile is (NULL) // Router tried to find any IPSec SA matching the outgoing connection but no valid SA has been found in Security Association Database (SADB)
Mar 2 16:18:42.939: ISAKMP: Created a peer struct for 20.1.1.10, peer port 500
Mar 2 16:18:42.939: ISAKMP: New peer created peer = 0x46519678 peer_handle = 0x8000000D
Mar 2 16:18:42.939: ISAKMP: Locking peer struct 0x46519678, refcount 1 for isakmp_initiator
Mar 2 16:18:42.939: ISAKMP: local port 500, remote port 500
Mar 2 16:18:42.939: ISAKMP: set new node 0 to QM_IDLE
Mar 2 16:18:42.939: ISAKMP:(0):insert sa successfully sa = 4542B818
Mar 2 16:18:42.939: ISAKMP:(0):Can not start Aggressive mode, trying Main mode. // Not an error. By default it is configured for Main Mode
Mar 2 16:18:42.939: ISAKMP:(0):No pre-shared key with 20.1.1.10! // Since we are using RSA Signature, this message. If we use pre-share, this is where it would indicate so!
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-rfc3947 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-07 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-03 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-02 ID
Mar 2 16:18:42.939: ISAKMP:(0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
Mar 2 16:18:42.939: ISAKMP:(0):Old State = IKE_READY New State = IKE_I_MM1
Mar 2 16:18:42.943: ISAKMP:(0): beginning Main Mode exchange
Mar 2 16:18:42.943: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_NO_STATE // Sending ISAKMP Policy to peer
Mar 2 16:18:42.943: ISAKMP:(0):Sending an IKE IPv4 Packet.
Mar 2 16:18:42.943: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_NO_STATE // Sending ISAKMP Policy to peer
Mar 2 16:18:42.947: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:42.947: ISAKMP:(0):Old State = IKE_I_MM1 New State = IKE_I_MM2
Mar 2 16:18:42.947: ISAKMP:(0): processing SA payload. message ID = 0
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch // Do not worry about this! Not an ERROR!
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
Mar 2 16:18:42.947:.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms
R2(config)# ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): processing IKE frag vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0):Support for IKE Fragmentation not enabled
Mar 2 16:18:42.947: ISAKMP : Scanning profiles for xauth ...
Mar 2 16:18:42.947: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
Mar 2 16:18:42.947: ISAKMP: encryption 3DES-CBC
Mar 2 16:18:42.947: ISAKMP: hash SHA
Mar 2 16:18:42.947: ISAKMP: default group 2
Mar 2 16:18:42.947: ISAKMP: auth RSA sig
Mar 2 16:18:42.947: ISAKMP: life type in seconds
Mar 2 16:18:42.947: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
Mar 2 16:18:42.947: ISAKMP:(0):atts are acceptable. Next payload is 0
Mar 2 16:18:42.947: ISAKMP:(0):Acceptable atts:actual life: 0
Mar 2 16:18:42.947: ISAKMP:(0):Acceptable atts:life: 0
Mar 2 16:18:42.947: ISAKMP:(0):Fill atts in sa vpi_length:4
Mar 2 16:18:42.947: ISAKMP:(0):Fill atts in sa life_in_seconds:86400
Mar 2 16:18:42.947: ISAKMP:(0):Returning Actual lifetime: 86400
Mar 2 16:18:42.947: ISAKMP:(0)::Started lifetime timer: 86400.
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.951: ISAKMP:(0): processing IKE frag vendor id payload
Mar 2 16:18:42.951: ISAKMP:(0):Support for IKE Fragmentation not enabled
Mar 2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM2
Mar 2 16:18:42.951: ISAKMP (0): constructing CERT_REQ for issuer cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
Mar 2 16:18:42.951: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_SA_SETUP // Sending Key Exchange Information to peer
Mar 2 16:18:42.951: ISAKMP:(0):Sending an IKE IPv4 Packet.
Mar 2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM3
Mar 2 16:18:42.955: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_SA_SETUP // Receive key exchange information from peer
Mar 2 16:18:42.955: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:42.955: ISAKMP:(0):Old State = IKE_I_MM3 New State = IKE_I_MM4
Mar 2 16:18:42.959: ISAKMP:(0): processing KE payload. message ID = 0
Mar 2 16:18:43.003: ISAKMP:(0): processing NONCE payload. message ID = 0
Mar 2 16:18:43.007: ISAKMP:(1008): processing CERT_REQ payload. message ID = 0
Mar 2 16:18:43.007: ISAKMP:(1008): peer wants a CT_X509_SIGNATURE cert
Mar 2 16:18:43.007: ISAKMP:(1008): peer wants cert issued by cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
Mar 2 16:18:43.007: Choosing trustpoint CA_Server as issuer
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID is Unity
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID seems Unity/DPD but major 180 mismatch
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID is XAUTH
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): speaking to another IOS box!
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008):vendor ID seems Unity/DPD but hash mismatch
Mar 2 16:18:43.007: ISAKMP:received payload type 20
Mar 2 16:18:43.007: ISAKMP (1008): His hash no match - this node outside NAT
Mar 2 16:18:43.007: ISAKMP:received payload type 20
Mar 2 16:18:43.007: ISAKMP (1008): No NAT Found for self or peer
Mar 2 16:18:43.007: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:43.007: ISAKMP:(1008):Old State = IKE_I_MM4 New State = IKE_I_MM4
Mar 2 16:18:43.011: ISAKMP:(1008):Send initial contact
Mar 2 16:18:43.011: ISAKMP:(1008):My ID configured as IPv4 Addr, but Addr not in Cert!
Mar 2 16:18:43.011: ISAKMP:(1008):Using FQDN as My ID
Mar 2 16:18:43.011: ISAKMP:(1008):SA is doing RSA signature authentication using id type ID_FQDN
Mar 2 16:18:43.011: ISAKMP (1008): ID payload
next-payload : 6
type : 2
FQDN name : R2
protocol : 17
port : 500
length : 10
Mar 2 16:18:43.011: ISAKMP:(1008):Total payload length: 10
Mar 2 16:18:43.019: ISAKMP (1008): constructing CERT payload for hostname=R2+serialNumber=FHK1502F2H8
Mar 2 16:18:43.019: ISAKMP:(1008): using the CA_Server trustpoint's keypair to sign
Mar 2 16:18:43.035: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_KEY_EXCH
Mar 2 16:18:43.035: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.035: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:43.035: ISAKMP:(1008):Old State = IKE_I_MM4 New State = IKE_I_MM5
Mar 2 16:18:43.047: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_KEY_EXCH
// "MM_KEY_EXCH" indicates that the peers have exchanged DH Public keys and generated a shared secret!
Mar 2 16:18:43.047: ISAKMP:(1008): processing ID payload. message ID = 0
Mar 2 16:18:43.047: ISAKMP (1008): ID payload
next-payload : 6
type : 2
FQDN name : ASA1
protocol : 0
port : 0
length : 12
Mar 2 16:18:43.047: ISAKMP:(0):: peer matches *none* of the profiles // Normal Message! Not an error!
Mar 2 16:18:43.047: ISAKMP:(1008): processing CERT payload. message ID = 0
Mar 2 16:18:43.047: ISAKMP:(1008): processing a CT_X509_SIGNATURE cert
Mar 2 16:18:43.051: ISAKMP:(1008): peer's pubkey isn't cached
Mar 2 16:18:43.059: ISAKMP:(1008): Unable to get DN from certificate!
Mar 2 16:18:43.059: ISAKMP:(1008): Cert presented by peer contains no OU field.
Mar 2 16:18:43.059: ISAKMP:(0):: peer matches *none* of the profiles
Mar 2 16:18:43.063: ISAKMP:(1008): processing SIG payload. message ID = 0
Mar 2 16:18:43.067: ISAKMP:received payload type 17
Mar 2 16:18:43.067: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.067: ISAKMP:(1008): vendor ID is DPD
Mar 2 16:18:43.067: ISAKMP:(1008):SA authentication status:
authenticated
Mar 2 16:18:43.067: ISAKMP:(1008):SA has been authenticated with 20.1.1.10
Mar 2 16:18:43.067: ISAKMP: Trying to insert a peer 40.1.1.1/20.1.1.10/500/, and inserted successfully 46519678. // SA inserted into SADB
Mar 2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM5 New State = IKE_I_MM6
Mar 2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM6 New State = IKE_I_MM6
Mar 2 16:18:43.071: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:43.071: ISAKMP:(1008):Old State = IKE_I_MM6 New State = IKE_P1_COMPLETE
Mar 2 16:18:43.071: ISAKMP:(1008):beginning Quick Mode exchange, M-ID of -1523793378
Mar 2 16:18:43.071: ISAKMP:(1008):QM Initiator gets spi
Mar 2 16:18:43.075: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE
Mar 2 16:18:43.075: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.075: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
Mar 2 16:18:43.075: ISAKMP:(1008):Old State = IKE_QM_READY New State = IKE_QM_I_QM1
Mar 2 16:18:43.075: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
Mar 2 16:18:43.075: ISAKMP:(1008):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
Mar 2 16:18:43.079: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) QM_IDLE // IPSec Policies
Mar 2 16:18:43.079: ISAKMP:(1008): processing HASH payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing SA payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008):Checking IPSec proposal 1
Mar 2 16:18:43.079: ISAKMP: transform 1, ESP_3DES
Mar 2 16:18:43.079: ISAKMP: attributes in transform:
Mar 2 16:18:43.079: ISAKMP: SA life type in seconds
Mar 2 16:18:43.079: ISAKMP: SA life duration (basic) of 3600
Mar 2 16:18:43.079: ISAKMP: SA life type in kilobytes
Mar 2 16:18:43.079: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
Mar 2 16:18:43.079: ISAKMP: encaps is 1 (Tunnel)
Mar 2 16:18:43.079: ISAKMP: authenticator is HMAC-SHA
Mar 2 16:18:43.079: ISAKMP:(1008):atts are acceptable. // IPSec attributes are acceptable!
Mar 2 16:18:43.079: ISAKMP:(1008): processing NONCE payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
Mar 2 16:18:43.083: ISAKMP:(1008): Creating IPSec SAs
Mar 2 16:18:43.083: inbound SA from 20.1.1.10 to 40.1.1.1 (f/i) 0/ 0
(proxy 1.1.1.1 to 2.2.2.2)
Mar 2 16:18:43.083: has spi 0xA9A66D46 and conn_id 0
Mar 2 16:18:43.083: lifetime of 3600 seconds
Mar 2 16:18:43.083: lifetime of 4608000 kilobytes
Mar 2 16:18:43.083: outbound SA from 40.1.1.1 to 20.1.1.10 (f/i) 0/0
(proxy 2.2.2.2 to 1.1.1.1)
Mar 2 16:18:43.083: has spi 0x2B367FB4 and conn_id 0
Mar 2 16:18:43.083: lifetime of 3600 seconds
Mar 2 16:18:43.083: lifetime of 4608000 kilobytes
Mar 2 16:18:43.083: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE
Mar 2 16:18:43.083: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.083: ISAKMP:(1008):deleting node -1523793378 error FALSE reason "No Error"
Mar 2 16:18:43.083: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
Mar 2 16:18:43.083: ISAKMP:(1008):Old State = IKE_QM_I_QM1 New State = IKE_QM_PHASE2_COMPLETE // At this point tunnels are up and ready to pass traffic!
Verification Commands
#show crypto isakmp SA
#show crypto ipsec SA
Kindly rate if you find the explanation useful !!
Best Regards
Sachin Garg -
Configure AIR-LAP1041N in GUI Mode
I Have a Wireless Access Point (AIR-LAP1041N-A-K9) and i want to configure this access point in standalone mode. Please help me how i can configure in GUI (Graphical User Interface) mode with this access point..........
Regards
Md. Sariful Islam (Palash)Hi Palash,
AIR-LAP = Lightweight Mode. So you have to first convert to Autonomous/Standalone mode to get GUI access. Here are steps below :
Console into the AP :
1.Install an external TFTP tool such as tftpd32 tool from http://tftpd32.jounin.net/
2. Make sure you set the IP address for the AP if not set.
3. Download the IOS image onto the tftp's root directory. Use www.cisco.com-->support-->download software-->wireless software--> AP .-> Select IOS software.
4. Assign IP address in the range of the AP to the TFTP server.
5. Connect the ethernet port on AP to your TFTP Server ( Laptop )
6. On AP, type
debug capwap console cli
debug capwap cli no-reload
archive download-sw /overwrite /force-reload tftp://192.168.5.12/c1140-k9w7-tar.124-25d.JA.tar
Note: 1140 and 1040 image is the same.
Detailed Instructions:
Boot up :
Hit enter
User Access Verification
Username: cisco/admin
Password: Cisco
salil>en
salil>en
Password: Cisco
salil#show ip int brief
Interface IP-Address OK? Method Status Protocol
Dot11Radio0 unassigned NO unset up up
Dot11Radio1 unassigned NO unset up up
FastEthernet0 10.10.10.34 YES DHCP up up
Thanks..Salil -
Brocade FCX PoE with Cisco LAP
Hi,
We are using Brocade FCX PoE switches with AIR-LAP1142N-N-K9 and AIR-LAP1252AG-A-K9. We have some issues that may or may not be due to the Brocade-LAP links but would like a reality check with other Brocade sites. If you are successfully using Brocade PoE switches with Cisco LAPs can you give a typical port config?
Example configs we have have tried:
interface ethernet 1/1/2
no cdp enable
inline power power
interface ethernet 2/1/23
port-name TX_LWAP01
no fdp enable
no cdp enable
inline power power-by-class 4"
interface ethernet 2/1/12
inline power
Typical switch:
UNIT 1: compiled on Jun 17 2010 at 18:20:53 labeled as FCXS07100a
HW: Stackable FCX648S-HPOE
Thanks,
JohnHi John,
Unfortunetally, I will not be able to help you from the switch side. Maybe someone else reading the thread will do; but I wanted to tell you that 11n Access Points have special POE requirements to function as expected.
Check this http://www.cisco.com/en/US/prod/switches/epoe.html if you haven't seen it yet.
Hope this help you
Have a good day
Serge -
Cisco serie 5500 wireless controller
Hi,
We got a cisco serie 5500 wireless controller, software 7.4.110.0. our ssl certicate expired into 2 weeks, we purchase a new one but the SH1 fingerprint is not any more supported and now we must apply SH2. does our controller support SH2?
Thanks and kind regardsYes, WLC supports SH2.
If you do not want users to connect to a web page using a browser that is configured with SSLv2 only, you can disable SSLv2 for web authentication by entering the config network secureweb cipher-option sslv2 disable command. If you enter this command, users must use a browser that is configured to use a more secure protocol such as SSLv3 or later releases. The default value is enabled -
Hi all
I have before 2950 Switch with VTP Trunking
and mapping with router with VLAN
example in 2950
interface FastEthernet0/24
description TRUNK
switchport trunk allowed vlan 1,45
switchport mode trunk
no cdp enable
interface FastEthernet0/23
switchport access vlan 45
no cdp enable
Now i got Cisco 5500 Switch with
4 Blades all are 10/100 ports
now i want to use one blade for LAN
another Blade replace with Above 2950 config
trunk with Cisck router dotq setup
how can i make this setup
could one help me some docs or any asistance
thanks
ramHi Ram,
Your 5500 is chasis based switch and must be running Cat OS on that. Do a show mod on this and you will come to know tha diff modules installed in the slots. You are using an external router as described above for inter-vlan routing.What you need to do is get to the particular port taht you want to config a trunk and have the trunk setup on your router with sub-interfaces too.
for example, if you are connecting to 3/1 i.e 3rd module and 1st port on that then
set the trunk using the command
set trunk 3/1 on dot1q
allowing the vlans on the trunk
clear trunk 3/1 2-44,46-1000
Please go through the link below for detailed description.
http://www.cisco.com/en/US/products/hw/switches/ps663/products_configuration_example09186a008014859e.shtml
HTH,
-amit singh
Maybe you are looking for
-
Lost my iphone and erased through Icloud. now i have found it
I have erased the backups from Itunes. Found my iphone, but have not powered it up yet because the erase is still pending on Icloud. How can I delete the erase that I have set so that I do not lose all my stuff on my phone.
-
IPaq, Java & 3D Compatibility Question
Note: First off, I'm not entirely sure if this is the right forum to post this in, so I apologise if it's in the wrong place. Basically, I creating an application that involves creating a 3D landscape via Java 3D and also runs fine on the PC, with th
-
Hi, I have Photo/Pre Elements 10 installed on Win7-64. I previously had Photo/Pre 8. In 8, I could change the overall layout of the Organizer (change the size of sidebars, centre view window, etc), and it would keep when running the program the next
-
Advice needed on os x useability
I have an old iBook (300mhz G3, 192MB ram, Rev B, 6gb hdd) running OS 10.3.9 and I am not too familiar with the apple os. Is there a way to speed up the system with the setup I have? I dont have any money left to do any upgrades to the hardware. I ra
-
Why do my bookmarks keep multiplying?
I have may iPhone bookmarks and my Chrome bookmarks synced. But recently the bookmarks have started multiplying. Everytime I delete the multiplied bookmarks next time I check they have done it again. I gave up and now I have about 20 bookmarks from e