Configure DHCP on router and switch

Good afternoon,
I'm trying to configure DHCP using CLI on a 2610 router and 2950 switch. With my present config, the host at the end of the switch (configured to receive ip via DHCP) is not getting anything assigned. Here are some shows:
Router:
Router_1#show ip int br
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 192.168.10.1 YES manual up up (leading to switch)
Serial0/0 unassigned YES unset administratively down down
Serial0/1 unassigned YES unset administratively down down
Ethernet1/0 unassigned YES unset administratively down down
Ethernet1/1 unassigned YES unset administratively down down
Ethernet1/2 unassigned YES unset administratively down down
Ethernet1/3 unassigned YES unset administratively down down
Router_1#show ip dhcp pool
Pool acer_pool :
Utilization mark (high/low) : 100 / 0
Subnet size (first/next) : 0 / 0
Total addresses : 254
Leased addresses : 0
Pending event : none
1 subnet is currently in the pool :
Current index IP address range Leased addresses
192.168.10.1 192.168.10.1 - 192.168.10.254 0
Switch:
Switch_1#show ip int br
Interface IP-Address OK? Method Status Protocol
Vlan1 unassigned YES NVRAM    up up
FastEthernet0/1 unassigned YES unset up up (leading to router)
FastEthernet0/2 unassigned YES   unset       down down
FastEthernet0/3 unassigned YES   unset       down down
FastEthernet0/4 unassigned YES   unset       down down
FastEthernet0/5 unassigned YES   unset       down down
FastEthernet0/6 unassigned YES   unset       down down
FastEthernet0/7 unassigned YES   unset       down down
FastEthernet0/8 unassigned YES   unset       down down
FastEthernet0/9 unassigned YES   unset       down down
FastEthernet0/10 unassigned YES   unset       down down
FastEthernet0/11 unassigned YES   unset       down down
FastEthernet0/12 unassigned YES   unset       down down
FastEthernet0/13 unassigned YES   unset       down down
FastEthernet0/14 unassigned YES   unset       down down
FastEthernet0/15 unassigned YES   unset       down down
FastEthernet0/16 unassigned YES   unset       down down
FastEthernet0/17 unassigned YES   unset       down down
FastEthernet0/18 unassigned YES   unset       down down
FastEthernet0/19 unassigned YES   unset       down down
FastEthernet0/20 unassigned YES   unset       down down
FastEthernet0/21 unassigned YES   unset       down down
FastEthernet0/22 unassigned YES   unset       up up
FastEthernet0/23 unassigned YES   unset down down
FastEthernet0/24 unassigned YES   unset down down
What other info can I supply to resolve this?
Thanks.

Hi Moh,
First, thanks for pointing out that I'm in the wrong section of the forums. My bad. I'll pay closer attention next time.
Second, I tried your suggestion but it failed to work. I cleared the configs of the router so I could start with a clean slate and followed your commands to the letter. The host can't seem to get an IP assigned and the here's what I get with a Show IP DHCP Pool:
Router_1#show ip dhcp pool
Pool vlan1 :
Utilization mark (high/low) : 100 / 0
Subnet size (first/next) : 0 / 0
Total addresses : 254
Leased addresses : 0
Pending event : none
1 subnet is currently in the pool :
Current index IP address range Leased addresses
192.168.10.1 192.168.10.1 - 192.168.10.254 0
Am I missing something?

Similar Messages

Syslog for router and switch

Hi all,
Any one help me to configure router and switch log on windows server. I dont have any idea please send me link or guide to configure syslog server on windows. For PPTP vpn users also.

Hi,
Are you asking, "How do I set up my Windows server as a Syslog Server"... in order to receive messages from your routers and switches?
If so, I'd suggest a google search on syslog server - locate and download the software there, and it should have a configuration guide with it.
Was this the information you were looking for?
Curtis

Help with connecting MacBook Pro with Cisco Routing and Switches?

I'm running a CiscoASA 5510 router with several Cisco WS-C2960-48TT-L switches on a local network to connect with MacBook Pro. I need to be able to restrict access to specific users via their computer MAC address. ie: Joe Blow is limited to connecting through Switch 1 on port 10 and anywhere else he tries to plug in will simply not work.

You need to look at the documentation that came with your router and switches. Or ask your network admin to set it up. Your question has nothing to do with your Macbook Pro configuration. MAC filtering is done in the router not in the computers/devices connecting to the router.

Power consumption for router and switch

I have a linksys EZSX88W switch which I checked power consumption of 70ma idle. It's supplied by the adapter which has an output of 1000ma. Not sure what the consumption when switch is being used. I also have an WRT54GS but haven't checked consumption yet, but it's powered by the same 1000ma adapter. In an effort to save energy-that -GREEN FEELING- I was thinking of using on power adapter to power bothe the router and switch. Has anyone tried this yet?? Also if I posted this in the wrong area I hope the moderator will move the post.
thanks

So you are thinking of Powering on both the Devices using a single Power Adapter? Well never tried to make both the devices use a single power adapter. As far as i think its not possible. But if you still wish, you can give a try and check if that works for you or not.

ISE distributed : router and switch update

I have 2 ISE 1.2
I configured ISE1 as primary for PAN, MNT and PSN and it work fine
Now I am configuring ISE2 as secondary PAN, MNT and PSN
Found below the actual configuration of the router, switch and WLC where ISE1_IP is configured
1. Router (sub-interface and DHCP are configured on the router)
interface FastEthernet1.10
encapsulation dot1Q 10
ip address 192.168.1.1 255.255.255.0
ip helper-address ISE1_IP
2. Switch configuration
snmp-server host ISE1_IP version 2c ROpass
radius-server host ISE1_IP auth-port 1812 acct-port 1813
aaa server radius dynamic-author
client ISE1_IP server-key John23
On site_1, ISE1 is PAN, MNT and PSN primary then ISE2 is PAN, MNT and PSN secondary
On site_2, ISE1 is PAN, MNT primary and PSN secondary then ISE2 is PAN, MNT secondary and PSN primary
See below the configuration that I made after installed ISE2 secondary for PAN, MNT and PSN
1. Router site_1
interface FastEthernet1.10
encapsulation dot1Q 10
ip address 192.168.1.1 255.255.255.0
ip helper-address ISE1_IP
ip helper-address ISE2_IP
2. Switch site_1
snmp-server host ISE1_IP version 2c ROpass
snmp-server host ISE2_IP version 2c ROpass
radius-server host ISE1_IP auth-port 1812 acct-port 1813
radius-server host ISE2_IP auth-port 1812 acct-port 1813
aaa server radius dynamic-author
client ISE1_IP server-key John23
client ISE2_IP server-key John23
3. Router site_2
interface FastEthernet1.10
encapsulation dot1Q 10
ip address 192.168.1.1 255.255.255.0
ip helper-address ISE2_IP
ip helper-address ISE1_IP
4. Switch site_2 (I changed radius order only)
snmp-server host ISE1_IP version 2c ROpass
snmp-server host ISE2_IP version 2c ROpass
radius-server host ISE2_IP auth-port 1812 acct-port 1813
radius-server host ISE1_IP auth-port 1812 acct-port 1813
aaa server radius dynamic-author
client ISE1_IP server-key John23
client ISE2_IP server-key John23
Kindly have a look on my configuration after instelled ISE2 and tell me if it is OK
Please advise
Thanks in advance

I have 2 ISE 1.2
I configured ISE1 as primary for PAN, MNT and PSN and it work fine
Now I am configuring ISE2 as secondary PAN, MNT and PSN
Found below the actual configuration of the router, switch and WLC where ISE1_IP is configured
1. Router (sub-interface and DHCP are configured on the router)
interface FastEthernet1.10
encapsulation dot1Q 10
ip address 192.168.1.1 255.255.255.0
ip helper-address ISE1_IP
2. Switch configuration
snmp-server host ISE1_IP version 2c ROpass
radius-server host ISE1_IP auth-port 1812 acct-port 1813
aaa server radius dynamic-author
client ISE1_IP server-key John23
On site_1, ISE1 is PAN, MNT and PSN primary then ISE2 is PAN, MNT and PSN secondary
On site_2, ISE1 is PAN, MNT primary and PSN secondary then ISE2 is PAN, MNT secondary and PSN primary
See below the configuration that I made after installed ISE2 secondary for PAN, MNT and PSN
1. Router site_1
interface FastEthernet1.10
encapsulation dot1Q 10
ip address 192.168.1.1 255.255.255.0
ip helper-address ISE1_IP
ip helper-address ISE2_IP
2. Switch site_1
snmp-server host ISE1_IP version 2c ROpass
snmp-server host ISE2_IP version 2c ROpass
radius-server host ISE1_IP auth-port 1812 acct-port 1813
radius-server host ISE2_IP auth-port 1812 acct-port 1813
aaa server radius dynamic-author
client ISE1_IP server-key John23
client ISE2_IP server-key John23
3. Router site_2
interface FastEthernet1.10
encapsulation dot1Q 10
ip address 192.168.1.1 255.255.255.0
ip helper-address ISE2_IP
ip helper-address ISE1_IP
4. Switch site_2 (I changed radius order only)
snmp-server host ISE1_IP version 2c ROpass
snmp-server host ISE2_IP version 2c ROpass
radius-server host ISE2_IP auth-port 1812 acct-port 1813
radius-server host ISE1_IP auth-port 1812 acct-port 1813
aaa server radius dynamic-author
client ISE1_IP server-key John23
client ISE2_IP server-key John23
Kindly have a look on my configuration after instelled ISE2 and tell me if it is OK
Please advise
Thanks in advance

Link b/w router and switch

I am useing 2600 series router and trying to link it with a 2950 switch,
2950 switch is attached with a internet connection & layer 3 switches, 2600 series router is connecting with 2950 at the client permises, what will be the port configuration at both 2950 & 2600 series devices,
currently i configure sw mod trunk at 2950,
and IP at the fastethernet port of 2600 series router.
But when ever i try to telnet the router it cannot telnet

What VLAN are the devices from which you wish to telnet to the router ?
You need to configure the router as follows:
interface fastethernet0/1.10
encapsulation dot1q
ip address
Where VLAN is the VLAN you want to get to the router from ...
Pls do remember to rate posts.
Paresh

Ethernet configuration with SMC router and Titanium

This concerns a Titanium Powerbook G4/500 and an SMC 2804WBR router.
I plugged in a known-working Ethernet cable, and in System Preferences/Network, under Network Status for Built-In Ethernet, I got the message "The cable for Built-In Ethernet is not plugged in." A hardware test shows the Ethernet port to be functioning, but the TCP/IP tab, set for Using DHCP, shows no IP address, subnet mask, or router address. Renewing DHCP lease accomplishes nothing.
I went to the Ethernet tab and set the drop-down to Manually (Advanced) instead of Automatic. With a little experimentation I found that 10baseT/UTP in either full- or half-duplex connects with the router and lets the machine go on the Internet, but 100baseTX will not. The router lights for link and 100baseTX go on, but no addresses appear in the TCP/IP tab.
I use 100baseTX with a G4 and a Pismo Powerbook, so I know the router can work just fine at that speed using an Ethernet cable. Is there some glitch or weirdness peculiar to the original G4 Powerbook that won't allow it to communicate with the router at full speed? Is there some configuration through Terminal or elsewhere that will fix that?

Hi,
the PVDM is used when you E1/T1 interface. in your scenario you need to configure SIP trunk between your Voice GW and ISP.
you need to confirm the below settings:
Codec
SIP sever ip address
DTMF
you will create voip dial-peer toward your ISP and another dial-peer toward your call manager.
in this you are deploying CUBE. you need to configure
voice service voip
allow sip to sip
don't forget to add CUCM and ISP in the trust list under voice service voip
HTH
Anas
don't forget to rate the helpful posts

Router and Switch Passwords

Hi all
What is the difference in setting passwords to access the console, Telnet (line vty 0 4) and other passwords in routers and switches. Are all the commands and where you set the passwords at the cmd prompts the same etc
Regards
Glenn

console password is used to authenticate user when user will try to access device through console port.
Telnet password is used to authenticate user when user will telnet to the device from remotely.
Hope this URL will give you more information.
http://www.cisco.com/en/US/products/sw/iosswrel/ps1818/products_configuration_example09186a0080204528.shtml
http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a00800ca7d1.html
rate if it helps ...

Do I have to disable DHCP in router and configure DHCP role in essential server to make connection with internet

hi,
'do I have to enable DHCP role on essential server just like sbs server to configure internet and domain name , or that is not really necessary , the router dhcp is enough toconfigure essential server!
thanks
johan
h.david

The router DHCP is enough to use Essentials server. Essentials is designed to work with router dhcp out of the box, but you can choose to install DHCP role on server if you like. If you decide to do that, check the blog post from
here: http://blogs.technet.com/b/sbs/archive/2013/04/22/running-dhcp-server-on-windows-server-2012-essentials.aspx
Also check the Essentials documentation for more details from here:
http://technet.microsoft.com/en-us/library/cc514417.aspx

Behind Router and Switch, Can't Enter URLs Without Dot-Com

Hello all,
I switched my networking situation this morning and now I've lost my favorite feature...the ability to enter URLs without a .com and have Safari auto-complete them. Here's my setup:
Wall->modem->D-Link Wireless-G Router->Netgear Gigabit Switch->iMac
Before, I just had my iMac connected directly to the modem, but now I have some new devices that I needed to network in. The Internet and everything else is working correctly, it's just that one thing that really bothers me. I've thumbed around through manuals and D-Link's router settings and I can't seem to find the giant on/off switch switched to off. Any ideas? Help?
Thanks!

Mateo wrote:
Before, I just had my iMac connected directly to the modem, but now I have some new devices that I needed to network in. The Internet and everything else is working correctly, it's just that one thing that really bothers me. I've thumbed around through manuals and D-Link's router settings and I can't seem to find the giant on/off switch switched to off. Any ideas? Help?
Based on your description of the change, my guess is that your iMac used to deal with Time Warner DNS directly and now it may be using the DNS routing settings in the D-Link. As the former owner of a D-Link I would guess you might go look in the WAN settings for the DNS field on the D-Link (in the browser-based configuration utility) and make sure the IP address there matches whatever you had entered in the DNS field in the Network settings on your Mac.

%CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/0 (not full duplex) between Router and switch

On Router
rAWKRdae01 uptime is 1 day, 23 hours, 47 minutes
System returned to ROM by power-on
System restarted at 06:13:17 GMT Wed Aug 13 2014
System image file is "flash:c2800nm-advipservicesk9-mz.124-15.T9.bin"
interface FastEthernet0/0
no ip address
duplex auto
speed auto
end
Logs
================================
034146: Aug 15 05:55:40.231 UTC: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/0 (not full duplex), with sALKRdae01.baxter.com GigabitEthernet1/1/1 (full duplex).
034147: Aug 15 05:56:40.228 UTC: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/0 (not full duplex), with sALKRdae01.baxter.com GigabitEthernet1/1/1 (full duplex).
034148: Aug 15 05:57:04.420 UTC: %SEC-6-IPACCESSLOGP: list SecureInternet denied udp 192.230.123.37(53) -> 119.201.190.90(44014), 1 packet
034149: Aug 15 05:57:40.229 UTC: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/0 (not full duplex), with sALKRdae01.baxter.com GigabitEthernet1/1/1 (full duplex).
034150: Aug 15 05:58:40.230 UTC: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/0 (not full duplex), with sALKRdae01.baxter.com GigabitEthernet1/1/1 (full duplex).
034151: Aug 15 05:59:40.227 UTC: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/0 (not full duplex), with sALKRdae01.baxter.com GigabitEthernet1/1/1 (full duplex).
034152: Aug 15 06:00:05.707 UTC: %SEC-6-IPACCESSLOGP: list SecureInternet denied tcp 60.169.77.13(6000) -> 119.201.190.90(8088), 1 packet
034153: Aug 15 06:00:27.476 UTC: %SEC-6-IPACCESSLOGP: list SecureInternet denied tcp 109.120.169.206(80) -> 112.217.135.50(11), 1 packet
034154: Aug 15 06:00:40.224 UTC: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/0 (not full duplex), with sALKRdae01.baxter.com GigabitEthernet1/1/1 (full duplex).
034155: Aug 15 06:01:40.225 UTC: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/0 (not full duplex), with sALKRdae01.baxter.com GigabitEthernet1/1/1 (full duplex).
================================
On Switch
interface GigabitEthernet1/1/1
description connection to rAWKRdae01
switchport trunk native vlan 100
switchport trunk allowed vlan 100
switchport mode trunk
load-interval 30
speed 100
duplex full
service-policy output 3850_QUEUE_2P6Q3T
end
Log:
=================================
000440: Aug 15 05:44:59 GMT: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet1/1/1 (not half duplex), with rAWKRdae01.baxter.com FastEthernet0/0 (half duplex).
000441: Aug 15 05:45:59 GMT: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet1/1/1 (not half duplex), with rAWKRdae01.baxter.com FastEthernet0/0 (half duplex).
000442: Aug 15 05:46:59 GMT: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet1/1/1 (not half duplex), with rAWKRdae01.baxter.com FastEthernet0/0 (half duplex).
000443: Aug 15 05:47:59 GMT: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet1/1/1 (not half duplex), with rAWKRdae01.baxter.com FastEthernet0/0 (half duplex).
000444: Aug 15 05:48:22 GMT: %SNMP-3-AUTHFAIL: Authentication failure for SNMP req from host 10.5.35.33
000445: Aug 15 05:48:59 GMT: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet1/1/1 (not half duplex), with rAWKRdae01.baxter.com FastEthernet0/0 (half duplex).
000446: Aug 15 05:49:59 GMT: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet1/1/1 (not half duplex), with rAWKRdae01.baxter.com FastEthernet0/0 (half duplex).
000447: Aug 15 05:50:59 GMT: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet1/1/1 (not half duplex), with rAWKRdae01.baxter.com FastEthernet0/0 (half duplex).
==================================
I did try to change duplex setting on fa0/0 of router to Full, but the interface went down and I lost the connectivity to the switch.

> I did try to change duplex setting on fa0/0 of router to Full, but the interface went down and I lost the connectivity to the switch.
Did you wait some time to let the divices reestablish the connection again?
I would configure the Switchport to auto/auto in that case. Autonegotiation works (most of the times ;-) ).

"no keepalive" and "no shutdown" command on router and switch interface

Hello
I am confused about the no keepalive and no shutdown command on different interface type on router. In serial interface, the status is down/down. But in ethernet interface, it is up/up. Could anyone please clear me?
And can this reason apply with Catalyst too?
Thanks a lot,
Nitass

Hi Nitass,
Yes I see the same on my router.
OKH-PBAGH-GRGNPRNT#sh int fa 0/1
FastEthernet0/1 is up, line protocol is down
Hardware is AmdFE, address is 000b.5faa.6961 (bia 000b.5faa.6961)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
OKH-PBAGH-GRGNPRNT(config)#int fa 0/1
OKH-PBAGH-GRGNPRNT(config-if)#no kee
OKH-PBAGH-GRGNPRNT(config-if)#no keepalive
OKH-PBAGH-GRGNPRNT(config-if)#end
OKH-PBAGH-GRGNPRNT#show int fa 0/1
FastEthernet0/1 is up, line protocol is up
Hardware is AmdFE, address is 000b.5faa.6961 (bia 000b.5f
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
I dont have a cable connected to it.
But its not the same on the serial interface and the ethernet interface of the L3 switch. They have different behaviur then this.they stay down/down.
PJB-UPW-PRI#sh int s 0/4
Serial0/4 is down, line protocol is down
Hardware is GT96K Serial
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
PJB-UPW-PRI(config)#int s 0/4
PJB-UPW-PRI(config-if)#no kee
PJB-UPW-PRI(config-if)#no keepalive
PJB-UPW-PRI(config-if)#end
PJB-UPW-PRI#sh int s 0/4
Serial0/4 is down, line protocol is down
Hardware is GT96K Serial
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive not set
4510_Switch_C48_BASEMENT(config)#int gig 3/19
4510_Switch_C48_BASEMENT(config-if)no keepalive
4510_Switch_C48_BASEMENT(config-if)#end
4510_Switch_C48_BASEMENT#show int g 3/19
GigabitEthernet3/19 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet Port, address is 0013.7f65.4582 (b
82)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
HTH,
-amit singh

Cisco VMS can support management of router and switches

I want to use Cisco VMS to manage my IPS and firewalls.
A also have two routere and five switches in place can i use the same software to monitor and manage them or I need separate software.

VMS 2.3 components and the capabilities of each. VMS is packaged in one sub-box with Obtaining Documentation directing you to VMS documentation and the following two CDs:
1.VMS Management and Monitoring Centers Disk 1 of 2Contains these VMS components and associated product documentation:
CiscoWorks Common Services
Auto Update Server
Management Center for Firewalls
Management Center for IPS Sensors1
Monitoring Center for Performance
Monitoring Center for Security
Management Center for VPN Routers
2.VMS Management and Monitoring Centers Disk 2 of 2Contains these VMS components and associated product documentation:
http://www.cisco.com/en/US/products/sw/cscowork/ps2330/products_installation_guide_chapter09186a00803bd364.html#wp1036990
Management Center for Cisco Security Agents
Resource Manager Essentials
Resource Manager Essentials IDU 12
Management Center for IDS Sensors 2.0.12
Monitoring Center for Security 2.0.13
Note You must install IDU 12 included on Disk 2 for RME to work with VMS 2.3 even if you already have RME 3.5 installed on your server.

Remote route and switch management

Good afternoon support community,
Does Cisco have a replacement for the 2811 console servers, newer with more features? I have been looking at opengear, but I wanted to know if Cisco had something equivalent to it. I'm looking for a way to manage devices via console, on a out of band network. If you have any recommendation please feel free to post them.
Thank you for your input.
Delmiro

There's not a direct replacement for the 2811 console server / router as far as I know.
Most customers I see are choosing either Opengear products or the Emerson (former Avocent, former Cyclades) ACS console servers. Link

SNMP MIB to configure the routers and switches

I have snmp write community string configured on all routers and switches. I am looking for a SNMP MIB to configure a command to Cisco routers and switches using SNMPSET option. Can some one point me in right direction for SNMP MIB values to write commands on routers and switches ?

Hi,
there are many, many mibs. Depends on what you are interested about, use search function on CCO. This is voip forum, there is another for network management.

Configure DHCP on router and switch

Similar Messages

Maybe you are looking for