Configuring ASA Simulation Interfaces on GNS3

Hello All,
I have managed to simulate to Cisco ASA's on GNS3 - ASA1 and ASA2.
ASA2 is configured as multiple mode to enable contexts while ASA2 has been configured as single mode.
On ASA2 I can assign an IP address to its gigabitethernet interfaces as normal, however I'm unable to assign an interface to the gigabitethernet interfaces on ASA1.
Can someone please tell me why that is? I'm sure there is a simple explanation.
Cheers
Carlton

I am not sure how you are trying it but you would need to do this:
In the system context:
context Test
config-url Test.cfg
allocate-interface gig0/0
allocate-interface gig0/1
Changeto context Test
interface gig0/0
ip address 1.1.1.1 255.255.255.0
no shut
nameif inside
interface gig0/1
ip address 2.2.2.2 255.255.255.0\
nameif outside
no shut
Hope that helps.
Thanks,
Varun Rao
Security Team,
Cisco TAC

Similar Messages

VPN ASA inside Interface and ip pool are one same Subnet

Hi Everyone,
I have configured RA VPN full tunnel.
Inside interface of ASA is
Vlan1 inside 10.0.0.1 255.255.255.0 CONFIG
ip local pool 10-pool 10.0.0.51-10.0.0.100 mask 255.255.255.0
Need to know is it good design to have both on same subnet?
When i access the Switch connecting to VPN ASA inside interface via--https://10.0.0.2
which has IP 10.0.0.2 while using Remote VPN connection to ASA it does not work gives error
message as below
Jan 19 2014 19:42:46: %ASA-5-305013: Asymmetric NAT rules matched for forward and reverse flows; Connection for tcp src outside:10.0.0.51/51077(LOCAL\ipsec-user) dst inside:10.0.0.2/443 denied due to NAT reverse path failure.
Jan 19 2014 19:42:57: %ASA-5-305013: Asymmetric NAT rules matched for forward and reverse flows; Connection for tcp src outside:10.0.0.51/51078(LOCAL\ipsec-user) dst inside:10.0.0.2/443 denied due to NAT reverse path failure
Jan 19 2014 19:42:59: %ASA-6-302014: Teardown TCP connection 22418 for outside:10.0.0.51/51069(LOCAL\ipsec-user) to identity:10.0.0.1/443 duration 0:01:08 bytes 1035 TCP Reset-O (ipsec-user)
Jan 19 2014 19:42:59: %ASA-6-106015: Deny TCP (no connection) from 10.0.0.51/51069 to 10.0.0.1/443 flags FIN ACK on interface outside
Current NAT config is
nat (inside,outside) source dynamic any interface
Regards
MAhesh
Message was edited by: mahesh parmar

Hi Mahesh,
It should work but I generally would not suggest having the same network on the LAN and also configured partially as a VPN Pool network.
Your problem at the moment is simply lacking the NAT0 configuration for the traffic between LAN and VPN Pool.
I would suggest changing the VPN Pool first and then configuring this
object network LAN
subnet 10.0.0.0 255.255.255.0
object network VPN-POOL
subnet
nat (inside,outside) 1 source static LAN LAN destination static VPN-POOL VPN-POOL
We have to use the line number "1" in the above command so that it gets moved to the top since your current Dynamic PAT would otherwise override it.
In the future it would be best if you changed your current Dynamic PAT configuration to this
nat (inside,outside) after-auto source dynamic any interface
We simply add the "after-auto" to this Dynamic PAT configuration so that it gets moved down in priority. The "after-auto" refers to the fact that this NAT will be inserted after Auto NAT (after Section 2). Your current rule is Manual NAT (Sectiom 1). The new rule will be Manual NAT (Section 3)
- Jouni

SVC WebVPN (clientless) uses IP pool addressing or ASA inside interface IP

I'm trying to design something which requires ASA to uniquely assign one IP per clientless VPN user. it seems like all these web requests coming through the ASA are proxied via the ASA's inside IP for the source address of the Web request. Does ASA proxy requests through it by changing the VPN client request IP's from a POOL configuration. Or is it always going to use the ASA inside interface IP? Assuming a two NIC configuration (inside/outside)
NOTE: I'm not talking about AnyConnect, IKEV1/2 client based VPN's. I'm specifically talking about the client-free login connection method.
thx in advance,
Will

Hi Will,
Pls move your thread to here
https://supportforums.cisco.com/community/6001/vpn
HTH
Rasika

Simulation interface toolkit tutorial

I'm trying to perform the tutorial titled "Converting a Simulink Model into a Model DLL", found on p.22 the Simulation Interface Toolkit manual (http://www.ni.com/pdf/manuals/370420b.pdf).
It starts off by building a new Simulink model of a sine wave (p.9). On step 7 of that process, it mentions a "NISink" block from the "NI Toolkit Sinks" library in Labview. I do not see this library, and I got zero hits when I searched the libraries for "NISink". I do have a library callled "NI SIT Blocks" but it does not have a "NISink" block, only "SignalProbe", "SIT Out1", and "SIT In1".
I am using SIT V5.0 with Simulink V7.2(R2008b), but the tutorial appears to be a bit older, perhaps from SIT V2. I assume that "SIT Out1" has replaced "NISink" but, as a novice, assumptions bother me. Is there a more up-to-date users guide available? I found the "SIT 2009 Help" file online (http://zone.ni.com/reference/en-XX/help/371504E-01/) but the how-to's there do not contain any tutorials.

I found a help example that was installed on my system with Labview, obviously a little more up to date. It’s also found online here:
http://zone.ni.com/reference/en-XX/help/371504E-01/TOC5.htm
I ran through the help example for the SIT how-to "configuring a simulation" and it worked as expected. When I then proceeded to the "configuring a simulation on a real-time target", I found that tasks 1 and 2 were already complete and verified working from the first how-to. During task three, however, step 7 fails at compile time (see attached file matlab_output.txt)
It looks to me like it is mssing a header file from the Simulink Real Time Workshop (called rtwtypes.h). It contains declarations for some sized and unsized generic data types, including uint_T. However, that file is available in the regular RTW library directory. Not sure why I can use the SIT server in Simulink to control the s-function with LabView, but I can't build a stand alone DLL for a real time system.
Attachments:
matlab_output.txt ‏11 KB

FieldPoint and simulation interface toolkitHi

Hi i'm trying to use cFP-2010 (with cfP-AIO-610 module) with simulation interface toolkit, in MAX i can see the FieldPoint and it's modules and i think it's all well configured.Well when i open the SIT i choose Real Time Target with the cFP ip and the port where the SIT server is running after i go on Hardware I/O and when i try to configure NI FPGA i do add device and it's return :"labview did not detect any FPGA devices installed in the specified RT target ,The default hardware type PXI-7831R will be used".Where is the error?
THX

Hello Freddino,
is the Simulation Interface toolkit installed on the RT target you are planning to use as SIT server (in your case the cFP 2010)? The following document lists all the necessary steps to do complete this operation:
Configuring a Real-Time Target to Run the LabVIEW Simulation Interface Toolkit 3.0.x Server
After have configured you RT target properly, it may be correctly listed unded "Hardware I/O" into the SIT connection manager.
Hope this helps,
Best regards,
Fabio
Fabio M.
National Instruments
Embedded & OEM Systems Engineer

Simulation interface toolkit: SUB VI not executable error

Hi;
I have a real-time application where I model things in Simulink and use Simulation Interface Toolkit to carry out hardware-in-the-loop simulations. As a real-time target, I am using NI-PXI8106 with NI-PXI6251 DAQ card on it. Up until now, I was able to run my code just fine. However, for some reason, my vi didn't work today and gave several errors such as:
SubVI NI_SIT_sitclient.Lvlib:RVE.vi: SubVI is not executable
Details:The SubVI is not executable. You must fix all error in the subVI before this VI can run.
SubVI NI_SIT_sit Init Model.vi: SubVI is not executable
Details:The SubVI is not executable. You must fix all error in the subVI before this VI can run.
This is just few of many error that I received...In the details section of the error list window, the error statement are usually like the following:
SUBVI not supported for current target..
Type not supported in the current target...
The only thing that changed since the last time I ran this program with success is the IP change of the target machine..However, when I use Measurement and Automation tool, I am able to access my target machine (PXI8106) without a problem...Maybe there are some certain rules for IP settings on the PXI target? ...I can provide the details of my new IP configuration numbers if necessary...
I also reinstalled the SIT 5.0 on the target machine but It didn't do the trick. I am wondering if there is anyone out there who can help me out with this problem..
Thank you so much!
Kind Regards.

Hi there,
I was just wondering if you did manage to solve this problem. I'm a new user and have recently started using the Simulation interface toolkit. I have created my model using Simulink and used the real-time workshop to convert it to a .dll file. I tried to run it on labview and it seems to build it on the realtime target, however as soon as map it to the hardware (using a NI BNC-2111,It's just a bunch of analog inputs and output which I have connected to a voltmeter), a dialog box pops up with the the following error:
Error 1003 occurred during host VI initialization: SIT_test1.vi >> NI_SIT_sitclient.lvlib:sit Init Model.vi >> NI_SIT_sitclient.lvlib:sit Connect to Target.vi
<append>=========================
Simulation Interface Toolkit: The driver VI (SIT_Test_Driver.vi) is not executable.
Check the following:
1) You have not modified the driver VI.
2) You properly installed SIT and any necessary driver software on the target.
3) The target has not been locked from Measurement and Automation Explorer.
Do you want to launch the SIT Connection Manager dialog box and reconfigure the simulation?
Please look at the JPEG picture attached below to see how the error looks on my monitor.
Thanks
Attachments:
error1.JPG ‏135 KB

Simulation Interface Toolbox: Problems using sbRIO with Tutorial: "Using the Example Sinewave Model with a VxWorks CompactRIO Target"

Hello
I faced a problem when I tried to do the Tutorial "Using the Example Sinewave Model with a VxWorks CompactRIO Target".
My specifications are:
Software:
Win7 64-bit
Matlab 2010b with RTW (to compile the *.dll) (32-bit)
GNU-Toolchain 6.3 running in Virtual PC-XP-Mode (to generate the *.out)
Labview 2011 with Simulation Interface Toolbox 2011 (32-bit)
Hardware:
sbRIO-9631 (from Labview Embedded Platform Evaluation Kit)
I was able to compile a dll and an out file.
I created a custom fpga-Bitfile with the Tutorial "Creating a Custom FPGA Bitfile".
In a blank VI I made the Host-VI and with the SIT Connection Manager I created the Driver VIs.
Until here everything worked fine.
Now my problem appeared. As long as I don't create Hardware I/O Mappings my model runs fine on the sbRIO:
But when I try to map the in and out port of the model to a HW I/O I get this error:
What causes this error?
On my sbRIO following software is installed (followed this instruction: Configuring a Real-Time Target to Run the LabVIEW SIT Server)
Best regards
Patrick

I have exctly the same issue. here is my error
my fpga for the bitfile
my driverVI
and my installed software

Having issues after installing Essbase V9.3.1,configuring the SQL interface

I am having issues after installing Essbase V9.3.1 and configuring the SQL interface. we are using UNIX/AIX box for our Essbase server and UDB DB2 9.1 SP6 as our SQL Interface.
When tried to run an ESSCMD script to perform BUILDDIM operation on Essbase application using the load rule (with the SQL interface), got the error as recorded in the application log file and is attached at the bottom and the .odbc.ini file on the server looks as follows.
Can somebody tell me whether .odbc.ini needs any correction or what else should I do to correct the issue and able to work thru using SQL interface? Appreciate any help provided in this regard. Thanks,
.odbc.ini
[ODBC Data Sources]
DOLU003=IBM DB2 ODBC DRIVER
[DOLU003]
Driver=/home/db2inst1/sqllib/lib/libdb2.a
Database=DOLU003
[ODBC]
Trace=0
TraceFile=odbctrace.out
InstallDir=/home/db2inst1/sqllib/odbclib
[Mon Apr 20 15:16:29 2009]Local/New_Bud/Budget/Olapadm/Info(1021020)
Cannot read SQL driver name for [] from [home/hyperion/.odbc.ini]
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1013091)
Received Command [SQLRetrieve] from user [Olapadm]
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021020)
Cannot read SQL driver name for [] from [home/hyperion/.odbc.ini]
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021004)
Connection String is generated
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021041)
Connection String is [DSN=DOLU003;UID=...;PWD=...]
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021006)
SELECT Statement [SELECT * FROM DB2OLADM.BD_DIMENSION_DEF_PC WHERE DIMENSION_ID
= 12 ORDER BY TREE_NODE_NUM, PARENT_NODE, CHILD_NODE] is generated
[Mon Apr 20 15:16:44 2009]Local/New_Bud/Budget/Olapadm/Info(1021013)
ODBC Layer Error: [7] ==> [[DataDirect][ODBC 20101 driver]6013]
[Mon Apr 20 15:16:44 2009]Local/New_Bud/Budget/Olapadm/Info(1021014)
ODBC Layer Error: Native Error code [0]
[Mon Apr 20 15:16:44 2009]Local/New_Bud/Budget/Olapadm/Error(1021001)
Failed to Establish Connection With SQL Database Server. See log for more information
--------------------------------------------------------------------------------------------------------------------------------------------

I had similar errors when first setting up the SQL interface. Are you on a 64 bit operating system on the essbase server? If so Essbase needs to use the 32 bit odbc driver, not the default 64 bit driver.
The 32 bit driver is still available here SysWOW64\odbcad32.exe <-----This is the 32 bit (Use)
The Administrative tools by default uses system32\odbcad32.exe <----This is the 64 bit (Don't Use)
Once I opened the 32 bit driver interface directly and set it up the errors went away.

Why do we configure the Redundant Interface in CSS Public Face

Hi,
I have a question : Why do we configure the redundant interface in a CSS facing the public side of a CSS.
I understand the need for the interface in the server side though. Please refer to the URL below;
http://www.cisco.com/univercd/cc/td/doc/product/webscale/css/css_810/redundgd/vipredun.htm#wp1063393

this is not a requirement if your vips belong to the public vlan subnet.
But if your vip addresses are from a different subnet, then the upstream router needs a route pointing to the CSS redundant interface ip.
Gilles.

Configuring multiple dynamic interfaces in 5508

Hi,
I have 5508 controller where as ap-manager interface configuration is optional but since i have different topology at other end , I have 4507 configured with HSRP and i want to divide the AP traffic in both the switches therefore I will have to go ahead and configure multiple AP-manager interface and map with two different physical ports.
But I have challenge to configure multiple dynamic interfaces.
I want to create two wlans ( Internal wlan and guest wlan )
Internal WLAN : 192.168.10.0
default gateway : 192.168.10.1
internal DHCP server : 172.16.10.1
Physical Port : ............... ? which port to configure ? ( I have connectivity with port 1 & port 2 )
Guest WLAN : 192.168.20.0
Default gateway : 192.168.20.1
Internal DHCP server : 172.16.10.1
Physical port : ............... ? which port to configure ? ( I have connectivity with port 1 & port 2 )
I want to map it to multiple ports of dynamic interfaces for client traffic to physical ports.
how do i configure it ?

In adition to Nico's answer, I would go throught the detailed guide for the configuration of dynamic interfaces:
http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70mint.html#wp1167723.
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it.

Required SW for the Simulation Interface Toolkit

Hello,
I would like to add a LabVIEW front panel to my Matlab/Simulink model. According to the data sheet, the following software is required for the SIT:
System Requirements
The LabVIEW Simulation Interface Toolkit requires that you have a
proper license for the following products:
• MATLAB® version 6.0 or later
• Simulink version 4.0 or later
• Real-Time Workshop® version 4.0 or later
• Microsoft Visual C++ version 6.0 and
• LabVIEW version 7.0 or later
To simply create a LV front panel for my model, do I still need to have LabVIEW installed? If so, which versions would be compatible?
I currently have the student version of Matlab 6.0 and Simulink 4.0. Will the SIT work with the student version?
If I only want to create a LV front panel, do I still need to have the RT Workshop or Visual C++ installed?
Thank You,
Mike

Greetings!
Yes, you are required to get the sw as mentioned.
To simply create a LV front panel for my model, do I still need to have LabVIEW installed? If so, which versions would be compatible?
Yes, to create a LabVIEW user interface / front panel, LabVIEW is required. LabVIEW 8.2 is the latest version.
The Simulation Interface Toolkit (SIT) 3.0.2 updates SIT 3.0.1 to support LabVIEW 8.2, the LabVIEW 8.2 Real-Time Module, and the LabVIEW 8.2 FPGA Module. You also can use SIT 3.0.2 with LabVIEW 7.1.x or with LabVIEW 8.0.x. However, you cannot install SIT 3.0.2 for more than one version of LabVIEW on the same computer.
2. I currently have the student version of Matlab 6.0 and Simulink 4.0. Will the SIT work with the student version?
The MathWorks, Inc. MATLAB® / Simulink® application software R2006a.
The MathWorks, Inc. Real-Time Workshop® R2006a.
Support for The MathWorks, Inc. MATLAB® / Simulink® application software release 13.x or 14.0, 14.1, 14.2, 14.3
If you install SIT 3.0.2 for LabVIEW 7.1, you can use Microsoft Visual C++ 6.0 to convert models to model DLLs. If you install SIT 3.0.2 for LabVIEW 7.1.1, 8.0, 8.0.1, or 8.2, you can use either Visual C++ 6.0 or Visual C++ .NET 2003.
If you installed more than one version of The MathWorks, Inc. MATLAB® / Simulink® application software, SIT installs support only for the latest version on the computer.
You want to make sure the Matlab release is one amongst the above.
3. If I only want to create a LV front panel, do I still need to have the RT Workshop or Visual C++ installed
RT Workshop comes with SIT. You will have to get Visual C++ and use that compiler.
Thanks and hope this helps
Best regards
Avi Harjani

Simulation Interface Toolkit

Hello,
I'm using the Simulation Interface Toolkit 3.0 because I want to control a Simulink model in LabVIEW 7.1. For instance, I want to generate a sine wave using a constant block. In this manner I can provide to my Simulink model every kind of signal without changes in it.
To perform this task Simulink needs an input value at each integration step.
I would to know if this task is achievable and if someone could tell me something about the communication between LabVIEW and Simulink.
Thank you for your help!:smileywink:

Hi Alessio,
Maybe you have the solution to my problem:
I have a Simulink model that works with a LabVIEW VI using the Simulation Interface Toolkit and the SIT server.
In order to use this model and this VI without Simulink, I created a dll (nidll) of my Simulink model like shown in the following manual:
http://www.ni.com/pdf/manuals/370420b.pdf
By doing so, LabVIEW automatically created 6 VIs that should work with my model DLL.
My questions are:
- Can I use the VI that I previously made for my Simulink model with the model dll ?
- If yes, How ?
- If no, How can I use my model dll and these new VIs?
Thanks in advance.

Simulation Interface Toolkit 4.0 cannot map to indicator

I have LabVIEW 8.5, SIT 4.0 and Matlab R2007b which uses Simulink 7.0. NI has a manual and example for using the Simulation Interface Toolkit at http://digital.ni.com/manuals.nsf/websearch/679117802743CC128625732B00697485 I can map control signals just fine between LV and Simulink but when I try to connect an indicator such as a Waveform Graph or numeric indicator to Port 1 of a Simulink object like a Sum block or Sine Wave (as the example shows) it always says that the mapping is invalid and greys out the box. It seems like there is a bug here because this should just work. Port 1 of a Sum or Sine Wave should be its output as a scalar. Anyone that uses the SIT have any ideas?
I've attached the help file with example that I followed.
Message Edited by tmar89 on 05-22-2008 04:04 PM
Attachments:
lvsimtkhowtoconcepts.zip ‏163 KB

Here are some screen shots from the Simulink model to the VI and error.
Attachments:
ss3.png ‏13 KB
ss1.png ‏13 KB
ss2.png ‏30 KB

Simulation Interface toolkit not working

I am working on a simulation and control problem using LABVIEW and Matlab. I have installed the simulation interface toolkit. But, the SIT server is not running. I have added the lines:
"addpath('C:\SimulationInterfaceToolkit'); NISIT_AddPaths; NISITServer('start',6011);"
in the matlabrc.m file. The NI SIT blocks are available in the simulink library. When I start matlab, the line:
" SIT: Added paths for Simulation Interface Toolkit 2011" appears. But the lines: "Starting the SIT Server on Port 6011 SIT Server started" don't show when matlab starts. I am attaching the Matlab startup screen.
Please help me out with this.
Thank You
Attachments:
Matlab Startup Screen.PNG ‏101 KB

OK I solved )))
Try the follwowing:
1- uninstall Labview and Matlab and the simulation interface toolkit (SIT) (be sure that u have only one version from SIT)
2- If you are going to use SIT 2011...then you will need Labview 2011 for sure and Maximum version of Matlab 2010 I think.
Revise the combatibility of SIT with Matlab on google
Be sure to use MATLAB 32-bit version
hope it will help
thanks
A.Hakim

Simulation interface Toolkit을 깔아도 matlab에 블록이 다 생기지가 않습니다.

Simulation Interface Toolkit 3.0을 사용하고있고 LabVIEW 7.1을 사용하는 유저입니다, Matlab 6.5.1을 사용하고요
모터컨트롤을 하기위해서 미리 시뮬레이션을 하기위해 위의 툴킷을 사용하여 시뮬레이션을 해보려고하는데
Matlab의 Simulink블록에서 ni_sink블록과 XY_sink블록이 생기지 않아서 문제입니다.
어떻게 해결책좀 알려주세요

Configuring ASA Simulation Interfaces on GNS3

Similar Messages

Maybe you are looking for