Configuring - Cisco 2921 with Switch Module/POE PS and 3750-x 24 port switch

This is what I have
- Cisco 2921 router
         with SM-ES2-24-P switch module and
                 POE power supply
-Cisco 3750x- 24 port Switch
I have port G1/0 (which connects to 24p Switch Module port g0/26 logically) configured with 3 sub interfaces (management, User and VOIP)
I want to connect 3750x to G0/1 on 2921 via fiber GBIC but want to use same three VLANs
I can not daisy chain 3750x via the switch module because it does not have fiber port.
I do not want to create another routed (g0/1) interface because I want to keep Users on both switches on the same subnet without further splitting the subnet in two.
I hope I am not making this confusing.
How can I bridge g1/0 and g0/1 so I can pass vlan traffic between two switches?
Second problem i have is ...
I have a VOIP connected to switch module (SM) and it is not getting any power.
I went in to all the interfaces on SM and issued power inline auto command
On the SM (sh power inline) - available is 0.0(w)
on the 2921 (sh power inline)
   - power supply status is good,
   - maximun power available is 280.
   - interface G1/0( which connects to SM)
      *device is unknown
      * powered off
     * allocated 0.0 watts.
I already tried resetting SM
Is there any other command I need to issue?
thanks for your help.

I'm having a similar issue. I can get trunked connectivity between the switch module and the router if I put the IP address on the router sub interface, but not if I put it on a VLAN interface. I was hoping to have it on a VLAN sub interface on the router so I could use Gig0/1 and Gig0/2 to connect other switches and have them on the same VLANs. I'm using Gig1/0 on the router side and Gig0/51 on the switch side (48-port module).
Any help? Am I on the wrong track altogether?

Similar Messages

How to Configuration Cisco 3725 with NEC ASPILA EX

Dear all;
Now i have Cisco 3725 with 1-Port Channelized E1/T1/ISDN-PRI, i am connect to NEC ASPILA EX with PRI I/F (1PRIU-A1.
The controller link state up, but when clients dialin to RAS not have ring back or not connect to RAS.
anyone can help me?

Hi;
i'am config cisco as you recommended is "isdn protocol-emulate network" and "clock source should be internal". After the remote computer call to RAS it have modem signal and then connected, next time it disconnect. can i change some parameter for this problem or what i'am wrong?. I post config, status, and debug message for you. Help me..
===== show isdn status ===========
#show isdn status
Global ISDN Switchtype = primary-net5
ISDN Serial2/0:15 interface
******* Network side configuration *******
dsl 0, interface ISDN Switchtype = primary-net5
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0xFFFF7FFF
Number of L2 Discards = 0, L2 Session ID = 0
Total Allocated ISDN CCBs = 0
=============== sh controllers e1 2/0 brief ========
#sh controllers e1 2/0 brief
E1 2/0 is up.
Applique type is Channelized E1 - unbalanced
No alarms detected.
alarm-trigger is not set
Framing is CRC4, Line Code is HDB3, Clock Source is Internal.
Module type is Channelized E1/T1 PRI
Version info Firmware: 0000001D, FPGA: 0
Hardware revision is 0.0 , Software revision is 29
Protocol revision is 1
number of CLI resets is 0
receive remote alarm : 0,
transmit remote alarm : 0,
receive AIS alarm : 0,
transmit AIS alarm : 0,
loss of frame : 1,
loss of signal : 1,
Loopback test : 0,
transmit AIS in TS 16 : 0,
receive LOMF alarm : 0,
transmit LOMF alarm : 0,
========== Interface config.=============
controller E1 2/0
clock source internal
line-termination 75-ohm
pri-group timeslots 1-31
interface Serial2/0:15
no ip address
ip nat inside
encapsulation ppp
ip policy route-map nachi-worm
dialer rotary-group 1
dialer-group 1
isdn switch-type primary-net5
isdn protocol-emulate network
isdn incoming-voice modem
no fair-queue
no cdp enable
=================Debug Message when call to RAS ===========================
Mar 6 22:40:29 BANGKOK: ISDN Se2/0:15 Q931: RX <- SETUP pd = 8 callref = 0x000B
Bearer Capability i = 0x8090A3
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9838B
Exclusive, Channel 11
Calling Party Number i = 0x0081, N/A
Plan:Unknown, Type:Unknown
Called Party Number i = 0x81, '075205600'
Plan:ISDN, Type:Unknown
Low Layer Compat i = 0x8090A3
High Layer Compat i = 0x9181
Mar 6 22:40:29 BANGKOK: ISDN Se2/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x800B
Channel ID i = 0xA9838B
Exclusive, Channel 11
Mar 6 22:40:29 BANGKOK: ISDN Se2/0:15 Q931: TX -> ALERTING pd = 8 callref = 0x800B
Mar 6 22:40:29 BANGKOK: ISDN Se2/0:15 Q931: TX -> CONNECT pd = 8 callref = 0x800B
Mar 6 22:40:35 BANGKOK: %ISDN-6-CONNECT: Interface Serial2/0:10 is now connected to unknown unknown
Mar 6 22:40:46 BANGKOK: %ISDN-6-DISCONNECT: Interface Serial2/0:10 disconnected from unknown , call lasted 17 seconds
Mar 6 22:40:46 BANGKOK: ISDN Se2/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x800B
Cause i = 0x8290 - Normal call clearing
Mar 6 22:40:47 BANGKOK: ISDN Se2/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x000B
Mar 6 22:40:47 BANGKOK: ISDN Se2/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x800B
==============================================

Multiple errors with DSC modules modbus master and slave

Hi,
I've searched quite a lot of posts but haven't found solution for my problem. I'm playing with LabVIEW DSC module and it's modbus master and slave functionalities. Even the LabVIEWs own modbus examples (Modbus Simulator and Fundamentals) seem to work randomly or not at all: When checking the Variable Manager utility Modbus Simulator (i.e. modbus slave/server) seems to deploy variables correctly with good quality but Modbus Fundamentals (i.e. modbus master/client) most often shows unknown value or bad quality for all the variables. When running the VIs I get 'Error -1950679035 Unable to locate variable in the Shared Variable Engine' and sometimes some other errors too. If the Modbus Simulator (slave/server) is expected to work fine I guess I should get two slaves communicating, but this isn't happening either. So maybe Modbus Simulator example isn't working either.
I've tried undeploying and deploying the libraries, stopping and starting the SVE, booting PC, reinstalling DSC module, and setting firewall and antivirus software off. This problem is going on with two different computers, both of which have recently installed LabVIEW 2011, first PC with Win XP and second PC with Win 7. No other OPC servers should be installed to these computers. And what is really interesting, the problem seems to have nothing to do with my network since Simulator and Fundamentals examples are not working even if the network cable is unplugged!
Any suggestions? Replies are highly appreciated!

V8 has the same feature, but the words are different.
The Generator typically uses the Driver time base, and the Gl. Var Write is writing once per block.
So, to see all values, you must have a block size of one.
I set up the Driver timebase to 10 Hz, block size of 1. The Generator and the Read Variable default to the Driver timebase.
The Generator is making a 2 Hz Rectangle waveform. YOu can see that it's shifted, but otherwise intact.
- cj
Measurement Computing (MCC) has free technical support. Visit www.mccdaq.com and click on the "Support" tab for all support options, including DASYLab.

Netgear CVG 824g and Linksys SLM2024 24 port switch

Hiya people
I have just installed a Linksys SLM2024 switch in my house and it - along with my Netgear CVG 824g router - delivers internet access to around 20 devices requiring IP's.
My problem is: The Netgear router can only assign IP adresses in the 192.168.0.XXX range. which means I cannot access the Linksys SLM2024's online configuration page which is located at 192.168.1.254. Are there any way to force the Linksys switch into having an IP in the 192.168.0.XXX range? I could try and connect only my laptop, the switch and an old router I have in a network and letting the DHCP server in the old router give my switch the correct IP. Though that just seems like a real hassle if there is an easier solution.
Can you help me?

Unfortunately that is not possible with this router. I tried to do just that and got an error message with the "You cannot have your own computer on the Guest IP LAN" - and I have no clue why I cannot. I found the answer to my original question on the Yousee forum. There are apparently quite a lot of people who are mad at the Netgear router.

Cisco 6509 with 10G Module

Hello,
We have Cisco 6509 Core Switch with following details & we need to install WS-X6716-10T-3C module in int.
Can some body advise which slot number i should use in 6509 ?
Do i need to upgrade supervisor engine IOS for this ?
Is it hot swapable module & can i install this module in production ?
6509_CORE#sh ver
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI6, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Mon 28-Mar-11 12:09 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)
6509_CORE uptime is 2 years, 30 weeks, 1 day, 3 hours, 13 minutes
Uptime for this control processor is 2 years, 30 weeks, 1 day, 1 hour, 44 minutes
Time since AUB_CORE switched to active is 2 years, 30 weeks, 1 day, 1 hour, 44 minutes
System returned to ROM by power cycle at 11:55:23 UTC Wed Apr 27 2011 (SP by power-on)
System restarted at 11:16:22 AST Sun Jun 26 2011
System image file is "sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI6.bin"
Last reload reason: Reload Command
cisco WS-C6509-E (R7000) processor (revision 1.5) with 983008K/65536K bytes of memory.
Processor board ID SMC1426001S
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
4294967295 Ethernet interfaces
33 Virtual Ethernet interfaces
150 Gigabit Ethernet interfaces
100 Ten Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
6509_CORE#sh module
Mod Ports Card Type                              Model              Serial No.
1   24 CEF720 24 port 1000mb SFP              WS-X6724-SFP       SAL1430P2QU
2   48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX     SAL1429N6XB
3   16 CEF720 16 port 10GE                    WS-X6716-10GE      SAL1430NYUE
4   16 CEF720 16 port 10GE                    WS-X6716-10GE      SAL1430NX5A
5    5 Supervisor Engine 720 10GE (Active)    VS-S720-10G        SAL1430NUJE
7   16 CEF720 16 port 10GE                    WS-X6716-10GE      SAL1645RJTF
Mod MAC addresses                       Hw    Fw           Sw           Status
1 d0d0.fd62.d9e0 to d0d0.fd62.d9f7   4.4   12.2(18r)S1 12.2(33)SXI6 Ok
2 c84c.75b8.596c to c84c.75b8.599b   3.4   12.2(18r)S1 12.2(33)SXI6 Ok
3 001f.6cac.11d0 to 001f.6cac.11df   1.0   12.2(18r)S1 12.2(33)SXI6 Ok
4 5475.d06e.0988 to 5475.d06e.0997   1.0   12.2(18r)S1 12.2(33)SXI6 Ok
5 001e.4a7f.3068 to 001e.4a7f.306f   3.2   8.5(4)       12.2(33)SXI6 Ok
7 fc99.4736.2d80 to fc99.4736.2d8f   1.1   12.2(18r)S1 12.2(33)SXI6 Ok
Mod Sub-Module                  Model              Serial       Hw     Status
1 Distributed Forwarding Card WS-F6700-DFC3C     SAL1430P282 1.4    Ok
2 Centralized Forwarding Card WS-F6700-CFC       SAL1430NRAS 4.1    Ok
3 Distributed Forwarding Card WS-F6700-DFC3C     SAL1430P26L 1.4    Ok
4 Distributed Forwarding Card WS-F6700-DFC3C     SAL1430NZRM 1.4    Ok
5 Policy Feature Card 3       VS-F6K-PFC3C       SAL1429N6B7 1.1    Ok
5 MSFC3 Daughterboard         VS-F6K-MSFC3       SAL1430NN3R 5.0    Ok
7 Distributed Forwarding Card WS-F6700-DFC3C     SAL1644RAZF 1.5    Ok
Mod Online Diag Status
1 Pass
2 Pass
3 Pass
4 Pass
5 Pass
7 Pass

Hello cmarva,
I got power requirement from core switch:
6509_CORE#show power
system power redundancy mode = redundant
system power total =     3795.12 Watts (90.36 Amps @ 42V)
system power used =      2748.06 Watts (65.43 Amps @ 42V)
system power available = 1047.06 Watts (24.93 Amps @ 42V)
                        Power-Capacity PS-Fan Output Oper
PS   Type               Watts   A @42V Status Status State
1    WS-CAC-4000W-INT   3795.12 90.36 OK     OK     on
2    WS-CAC-4000W-INT   3795.12 90.36 OK     OK     on
                        Pwr-Allocated Oper
Fan Type               Watts   A @42V State
1    WS-C6509-E-FAN      210.00 5.00 OK
                        Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type          Watts   A @42V Watts   A @42V State State
1    WS-X6724-SFP        162.96 3.88   162.96 3.88 on   on
2    WS-X6748-GE-TX      325.50 7.75   325.50 7.75 on    on
3    WS-X6716-10GE       457.80 10.90   457.80 10.90 on    on
4    WS-X6716-10GE       457.80 10.90   457.80 10.90 on    on
5    VS-S720-10G         338.10 8.05   338.10 8.05 on    on
6    (Redundant Sup)       -     -      338.10 8.05 -     -
7    WS-X6716-10GE       457.80 10.90   457.80 10.90 on    on
system auxiliary power mode = off
system auxiliary power redundancy operationally = non-redundant
system primary connector power limit =   10920.00 Watts (260.00 Amps @ 42V)
system auxiliary connector power limit = 10500.00 Watts (250.00 Amps @ 42V)
system primary power used =              2748.06 Watts (65.43 Amps @ 42V)
system auxiliary power used =            0 Watt
As per Cisco document i require this power WS-X6716-10T-3C: 509.3W (12.1A @ 42V) & from output available power is system power available = 1047.06 Watts (24.93 Amps @ 42V)
Looks like im good to go. Can you verify please ?
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6500-series-switches/product_data_sheet09186a00801dce34.html
Regards,

Does anyone configure cisco router with MGCP to link Call agent Clarent ?

hi,
We require to configure As5300 with MGCP to link Clarent call agent. Does anyone have cisco router configuration ?
thanks.
best regards.
fred.

Below is the sample configuration for the 5300 to Call-Agent. This is also dependant on which package is configured on the call-agent so we can configure it accordingly. Hope this helps.
version 12.3
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname AS5300-5
boot system tftp c5300-is-mz.123-2.T1 171.68.191.135
logging buffered 100000 debugging
enable password xxxx
backhaul-session-manager
set bh5300-vsc1 client nft
group bhgrp1 set bh5300-vsc1
session group bhgrp1 172.16.20.35 7007 172.16.20.28 7007 0
isdn switch-type primary-ni
isdn voice-call-failure 0
no scripting tcl init
no scripting tcl encdir
voice call carrier capacity active
voice class codec 1
codec preference 1 g723r63
codec preference 2 g711ulaw
no voice hpi capture buffer
no voice hpi capture destination
dial-control-mib retain-timer 240
dial-control-mib max-size 600
controller T1 0
framing esf
clock source line primary
linecode b8zs
pri-group timeslots 1-24 service mgcp
controller T1 1
framing esf
clock source line secondary 1
linecode b8zs
ds0-group 0 timeslots 1-24 type none service mgcp
controller T1 2
framing esf
clock source line secondary 2
linecode b8zs
controller T1 3
framing esf
clock source line secondary 3
linecode b8zs
interface Ethernet0
no ip address
no ip mroute-cache
shutdown
interface Serial0
no ip address
no ip mroute-cache
shutdown
clockrate 2015232
no fair-queue
interface Serial1
no ip address
no ip mroute-cache
shutdown
clockrate 2015232
no fair-queue
interface Serial2
no ip address
no ip mroute-cache
shutdown
clockrate 2015232
no fair-queue
interface Serial3
no ip address
no ip mroute-cache
shutdown
clockrate 2015232
no fair-queue
interface Serial0:23
no ip address
isdn switch-type primary-ni
isdn bind-l3 backhaul bh5300-vsc1
no cdp enable
interface FastEthernet0
ip address 172.16.20.28 255.255.255.192
no ip mroute-cache
duplex full
speed auto
no cdp enable
ip classless
ip route 0.0.0.0 0.0.0.0 172.16.20.1
no ip http server
radius-server host 172.21.59.165 auth-port 1645 acct-port 1646
radius-server key xxxxxxxx
radius-server vsa send accounting
voice-port 0:23
voice-port 1:0
mgcp
mgcp call-agent 172.16.20.35 2427 service-type mgcp version 0.1
mgcp quarantine mode loop
mgcp package-capability dtmf-package
mgcp package-capability rtp-package
mgcp package-capability as-package
mgcp default-package gm-package
mgcp profile default
timeout tsmax 100
no max1 lookup
dial-peer cor custom

Cisco 3925 with ethsw module EoMPLS support

Hi,
I am looking for clarification that the ethsw module, NM-16ESW, will not allow for EoMPLS support?
From what I have read on CCO it seems to suggest that the EHWIC-4/8ESG is needed to support this?
Basically, I had 15.2(4)M1 on my 3925, but none of the EoMPLS VC's would come up for the vlans that were attached to the ethsw module. Other EoMPLS VC that used onboard gig ports came up just fine. All LDP signalling/routing is correct.
Can anyone provide any confirmation?
Thanks,
LR

Hi,
The switch (NM-16ESW) inside your router runs an image for the 3560 switches and the 3560 switches don't support MPLS. They only support vrf Lite.
HTH

Is 1841 router compatible with wic module U WIC -2MFT –G703 ( 2 E1 ports) ?

Hi frainds
I have cisco 1841 router
1841 Software (C1841-ADVSECURITYK9-M), Version 12.4(3g)
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
with
2 FastEthernet interfaces
2 Serial(sync/async) interfaces
1 Virtual Private Network (VPN) Module
will this router supoort Uwic 2 mft-g703 card ( with 2 E1ports) ,

These are the following modules supported on the 1841.
http://www.cisco.com/en/US/prod/collateral/routers/ps5853/product_data_sheet0900aecd8016a59b.html
The one you listed only works with the 1700 series which is end of life.
"If this post answers your question, please click the "Correct Answer" button"

Problems with WLS 4.5.1 and F5 Big IP HA+ Switch

Hello. We're having problems with our F5 Big IP HA+ switch and pool of WLS
          4.5.1 servers (two in the pool currently). At seemly random intervals the
          Big IP believes the one or both of the servers are not responding, so they
          are removed from the pool. We have a growing body of anecdotal evidence to
          suggest that the servers are actually on-line and available during the
          event. Either the switch is confused or the WLS servers aren't always
          responding correctly to the HTTP requests sent by the switch for polling.
          We're having problems catching the problem with the right diagnostics.
          Has anyone out there observed similar behavior with these components?
          Thanks.
          - Sean McRae


Sort of,
          I use iplanet between the 2, so I havent had this problem, but I have had
          several problems with clustering, here is what I recomend doing:
          write a simple java program (or whatever your prefered language) to do a HTTP
          ping on your distinct weblogic servers every X seconds/minutes where X is less
          than Big IPs death tolerance. Time how long/or if ever each of your pings take.
          turn on verbose gc.
          My guess is its one of 3 things:
          1.) your have a big gc going on and your server isnt responding quick enough
          and big ip is marking it dead
          2.) you have thread contention that is causing your server not to respond quick
          enough
          3.) your network has some issues and the packets arent making it there, or not
          quick enough.
          the ping program will prove/disprove #2 and lead you to or away from 3. Verbose
          gc will prove/disprove #1.
          hope this helps
          -Joel
          Sean wrote:
          > Hello. We're having problems with our F5 Big IP HA+ switch and pool of WLS
          > 4.5.1 servers (two in the pool currently). At seemly random intervals the
          > Big IP believes the one or both of the servers are not responding, so they
          > are removed from the pool. We have a growing body of anecdotal evidence to
          > suggest that the servers are actually on-line and available during the
          > event. Either the switch is confused or the WLS servers aren't always
          > responding correctly to the HTTP requests sent by the switch for polling.
          > We're having problems catching the problem with the right diagnostics.
          >
          > Has anyone out there observed similar behavior with these components?
          >
          > Thanks.
          >
          > - Sean McRae

HELP!! ClassCastException with custom module classloader hierarchy and redeployment

Hi,
I am defining custom module classloader hierarchy to avoid redeploying of the
entire application mainly because we have so many EJBs and it takes a long time
to deploy the entire app. I deploy my app using the exploded directory, add a
new method to an EJB in my dal.jar, redeploy, run my unittest and I get ClassCastException.
I am using weblogic.Deployer utility to reploy my module using "-targets dal.jar@accsserver"
argument. I even tried undeploying that module and redeploy again with no luck.
here is weblogic-application.xml definition of the custom class loader
<classloader-structure>
<module-ref>
     <module-uri>floghmi.war</module-uri>
     </module-ref>
<module-ref>
     <module-uri>cts.jar</module-uri>
     </module-ref>
<module-ref>
     <module-uri>fdbs.jar</module-uri>
     </module-ref>
<classloader-structure>
     <module-ref>
          <module-uri>dml.jar</module-uri>
     </module-ref>
<classloader-structure>
     <module-ref>
     <module-uri>dal.jar</module-uri>
</module-ref>
</classloader-structure>
</classloader-structure>
</classloader-structure>
thanks,
Nasrin

Rob,
regarding your question on redeploying the whole app without the classloader
structure, yes, that works fine. If I change a class and redeploy the whole app,
things are ok. However, when I speocify the classloader structure, and try to
redeploy the dal.jar, I get ClassClasException.
You are right about dml.jar being in a separate classloader. I have changed my
structure after I posted my question to load dml.jar from the application classloader.
So Rob, is there a bug in Weblogic 8.1 that causes this exception?
please let me know, I am anxiously waiting your response.
thanks,
Nasrin
Rob Woollen <[email protected]> wrote:
>
>
Nasrin Azordegan wrote:
Rob,
if I remove my classloader structure from weblogic-application.xml,I get an
error during redeployment, saying "You must include all of<list ofmy module names
here> in your files list to modify <dal.jar>. Yes, the server enforces constraints on partial redeployments. You must
deploy all the modules in a given classloader and any modules in child
classloaders.
Just to make sure, if you initially deploy your app, or redeploy the
whole thing, it works fine without the classloader-structure, right?
The problem I am trying to solve is to minimize our deployment time.Our application
has over 700 CMP 2.0 entity beans and 200 session beans. Our applicationdeployment
follows the J2EE layer architecture. The data mapping layer which consistof 700
entity beans are located in dml.jar. The data access layer which consistof 200
session beans are located in dal.jar. We create our ear with thesetwo jar files
plus some other framework jars and deploy on bea weblogic 8.1 SP2 andthat takes
about an hour. I need to be able to modify a session bean, i.e. changethe implementation
of a session bean or add a new method to a session bean interface andredeploy
only data access layer, the dal.jar, not the entity beans. This explainswhy you
see dml.jar in a classloader with a child classloader that loads dal.jar.
I included the ClassCastException from weblogic server console below.What is
happening is that I have a session bean with 6 methods that just doesa println.
I deploy my session bean, ExerciseSessionBeanFactory, and run my unittest that
invokes test1 through test6 methods. I modify my bean to add "test7"method and
redeply dal.jar successfully. I run my unit test that invokes test1through test7
methods and then I get a ClassCastException.
I hope this helps. Please let me know if you need more details.If you push dml.jar into a subloader, that means you can change dml.jar
without touching anything in the parent loader. However, it also means
that you've isolated it's classes and other modules can't see them.
-- Rob
thanks,
Nasrin
in test method
in test2 method
in test3 method
in test4 method
in test5 method
in test6 method
<Apr 12, 2004 9:26:03 AM PDT> <Warning> <EJB> <BEA-010096> <The Message-Driven
EJB: SimTimeListener is unable to connect
to the JMS destination: cn=t.cms.cts.simTimeInfo. Connection failedafter 184
attempts. The MDB will attempt to reconne
ct every 10 seconds. This log message will repeat every 600 secondsuntil the
condition clears.>
<Apr 12, 2004 9:26:03 AM PDT> <Warning> <EJB> <BEA-010061> <The Message-Driven
EJB: SimTimeListener is unable to connect
to the JMS destination: cn=t.cms.cts.simTimeInfo. The Error was:
[EJB:011011]The Message-Driven EJB attempted to connect to the JMSdestination
with the JNDI name: cn=t.cms.cts.simTimeI
nfo. However, the object with the JNDI name: cn=t.cms.cts.simTimeInfois not a
JMS destination, or the destination found
was of the wrong type (Topic or Queue).>
in test method
in test2 method
in test3 method
in test4 method
in test5 method
in test6 method
<Apr 12, 2004 9:28:26 AM PDT> <Warning> <RMI> <BEA-080003> <RuntimeExceptionthrown
by rmi server: com.trs.cv.infr.istr.
sc.sim.factory.ejb.ExerciseSessionFactory_zhotso_EOImpl.test7()
java.lang.ClassCastException.
java.lang.ClassCastException
at com.trs.cv.infr.istr.sc.sim.factory.ejb.ExerciseSessionFactory_zhotso_EOImpl_WLSkel.invoke(Unknown
Source)
at weblogic.rmi.internal.BasicServerRef.invoke(BasicServerRef.java:477)
at weblogic.rmi.cluster.ReplicaAwareServerRef.invoke(ReplicaAwareServerRef.java:108)
at weblogic.rmi.internal.BasicServerRef$1.run(BasicServerRef.java:420)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:353)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:144)
at weblogic.rmi.internal.BasicServerRef.handleRequest(BasicServerRef.java:415)
at weblogic.rmi.internal.BasicExecuteRequest.execute(BasicExecuteRequest.java:30)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:197)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:170)
Rob Woollen <[email protected]> wrote:
You'll have to give me some more information on the ClassCastException.
Where does it happen? Print out the classnames and the
classloaders of the 2 objects.
Does everything work fine if you remove your classloader-structure?
-- Rob
Nasrin Azordegan wrote:
Hi,
I am defining custom module classloader hierarchy to avoid redeployingof the
entire application mainly because we have so many EJBs and it takesa long time
to deploy the entire app. I deploy my app using the exploded directory,add a
new method to an EJB in my dal.jar, redeploy, run my unittest and
I
get ClassCastException.
I am using weblogic.Deployer utility to reploy my module using "-targetsdal.jar@accsserver"
argument. I even tried undeploying that module and redeploy again
with
no luck.
here is weblogic-application.xml definition of the custom class loader
<classloader-structure>
<module-ref>
     <module-uri>floghmi.war</module-uri>
     </module-ref>
<module-ref>
     <module-uri>cts.jar</module-uri>
     </module-ref>
<module-ref>
     <module-uri>fdbs.jar</module-uri>
     </module-ref>
<classloader-structure>
     <module-ref>
          <module-uri>dml.jar</module-uri>
     </module-ref>
<classloader-structure>
     <module-ref>
     <module-uri>dal.jar</module-uri>
</module-ref>
</classloader-structure>
</classloader-structure>
</classloader-structure>
thanks,
Nasrin

Cisco 5508 with 7.0.98.0 and GTK interval

I am looking where I can change the GTK interval for my controller. Any pointers, appreciated.

You cannot.
It was possible on IOS but for some reason, it's not anymore on controllers.
Sorry.
Nicolas
===
Don't forget to rate answers that you find useful

Use RF switch module to switch 125M Hz differential signals

A customer has 1 pair output signal. The signal is differential, 900mVp-p, 125 MHz.
He sends to output signal to his DUT with 4 differential channels and uses switch to read the signal back in turn.
He needs to measure the voltage waveform to get the return Vp-p to determine pass or fail.
According to his needs and tutorial "Advanced Signal Routing with the NI PXI-2593 and NI SCXI-1193 RF Switches
", we have pxi-2593 or scxi-1193, which can be configured as 2xN topology to switch differential signals. In the spec, the insertion loss is 0.9dB when the signal is less then 500 MHz.
I have some questions:
1. Does that mean the voltage error is around 10%? (Accoreing to dB=20log(V/Vref)
2. What else parameter should I pay attention when I want to know the voltage error?
3. If the customer needs the voltage error less than 5%, do we have any solution?
Thank you for help.
Henry

chlin12 wrote:
A customer has 1 pair output signal. The signal is differential, 900mVp-p, 125 MHz.
He sends to output signal to his DUT with 4 differential channels and uses switch to read the signal back in turn.
He needs to measure the voltage waveform to get the return Vp-p to determine pass or fail.
According to his needs and tutorial "Advanced Signal Routing with the NI PXI-2593 and NI SCXI-1193 RF Switches
", we have pxi-2593 or scxi-1193, which can be configured as 2xN topology to switch differential signals. In the spec, the insertion loss is 0.9dB when the signal is less then 500 MHz.
I have some questions:
1. Does that mean the voltage error is around 10%? (Accoreing to dB=20log(V/Vref)
2. What else parameter should I pay attention when I want to know the voltage error?
3. If the customer needs the voltage error less than 5%, do we have any solution?
Thank you for help.
Henry
Hello Henry,
You have a couple of options. All of our RF switches are single-ended coax (one signal line surrounded by a ground). To route a differential signal, you'll need to split the pair out to two coax cables and use two banks of multiplexers. Since you only have a 4x1 requirement, you could use one PXI-2593 (dual 8x1) or two PXI-2590 (single 4x1 each) modules. The SCXI counterparts have more banks.
The characteristic impedance of these switches is 50 Ohms. What is the differential impedance of your input signal? Ideally, this split configuration would work best if the differential impedance was 100 Ohms (each half run downs a 50 Ohm line with no coupling between them). The more impedance mismatch you have, the more reflection and signal loss will occur.
As for the insertion loss, you are right that the voltage at 125 MHz will be attenuated by as much as 10% (typical is more like 5%), but it is repeatable. If you calibrate the system (including the switch and cables), you should be OK. The insertion loss through the switch, like contact resistance, is stable over the relay life.
What is the frequency content of this signal? Is it sinusoidal at 125 MHz, or a square wave with faster edges?
Hope this is useful.
Charles

Routing Issue Cisco 2921

Hi Everyone.... I need urgent help on the below scenario....
ISP Managed Router connected to ADSL & looked for me to view or change configuration.... i have successfully configured my own 2921 to work with ISP router with IP NAT, Internet is working for all my LAN Users.
After connecting the VPN from outside to managed services router... i am able to reach my 2921 (10.10.10,100) but unable to access Internal LAN interface which is (10.10.100.1) on-wards....
ISP Managed Router (10.10.10.1) >>>>>>>>>> (10.10.10.100) MY Router (2921) (10.10.100.1)>>>>>>>>>>DHCP Users (10.10.100.21 to 100)
CONFIGURATION OF 2921 Attached.
Please give suggestions and advise if i need to so some more settings on 2921.

Hi Paul,
I have changed the config as required.... yes ISP router side is 10.10.10.1
Still issues.... Internet is working fine for my LAN users...
When i connect VPN on ISP managed router - 78.93.181.41 its connected....
I can ping 10.10.10.0 range.... and able to reach my router which is 10.10.100.1.... but unable to access anything on 10.10.100.0 (which is my LAN)
Any ideas.... as i asked ISP to allow this in their router which they did....
access-list 10 permit 10.10.100.0 0.0.0.255
this what i get from 2921 now....
RGTSTHALIA2900#show ip nat translations
Pro Inside global Inside local Outside local Outside global
udp 10.10.10.100:1031 10.10.100.21:1031 192.168.1.111:161 192.168.1.111:161
udp 10.10.10.100:1031 10.10.100.21:1031 192.168.100.11:161 192.168.100.11:161
udp 10.10.10.100:1031 10.10.100.21:1031 192.168.100.111:161 192.168.100.111:161
udp 10.10.10.100:1031 10.10.100.21:1031 192.168.100.112:161 192.168.100.112:161
tcp 10.10.10.100:1674 10.10.100.21:1674 2.21.39.117:80 2.21.39.117:80
tcp 10.10.10.100:1734 10.10.100.21:1734 2.21.39.117:80 2.21.39.117:80
tcp 10.10.10.100:1735 10.10.100.21:1735 2.21.39.117:80 2.21.39.117:80
RGTSTHALIA2900#show ip route
Gateway of last resort is 10.10.10.1 to network 0.0.0.0
S* 0.0.0.0/0 [1/0] via 10.10.10.1, GigabitEthernet0/0
10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks
C 10.10.10.0/24 is directly connected, GigabitEthernet0/0
L 10.10.10.100/32 is directly connected, GigabitEthernet0/0
C 10.10.100.0/24 is directly connected, GigabitEthernet0/1
L 10.10.100.1/32 is directly connected, GigabitEthernet0/1

Is it ok to have 1 nic configured with 1 listener handling incoming and outgoing email?

I'm reading about public and private listeners and i am wondering is there any harm in configuring 1 nic with 1 listener handling incoming and outgoing mail flow.

Brannon,
I also think it will work fine; as I heard some time keep it simple
Luis Silva
"If you need PDI (Planning, Design, Implement) assistance feel free to reach"
http://www.cisco.com/web/partners/tools/pdihd.html

CISCO 1841 with SHDSL Problem?

Hello,
I´am new in cisco WIC configuration. I have a CISCO 1841 with a interface: 1SHDSL v3 and i want to connect to my ISP over a PPoE encapsulation.
I just make the new interface connection in SDM, but the synchronism with the ISP not work. The ISP tell me that VPI/VCI is 0.35 and the annex is the A.
I live in the Europe, but i think that the annex A is for POTS lines and Annex B for ISDN, right?? My line is ADSL Analog.
My startup-configuration is that:
Router#show run
Building configuration...
Current configuration : 2974 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
dot11 syslog
ip source-route
ip cef
no ipv6 cef
multilink bundle-name authenticated
crypto pki trustpoint TP-self-signed-2879799878
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2879799878
revocation-check none
rsakeypair TP-self-signed-2879799878
crypto pki certificate chain TP-self-signed-2879799878
certificate self-signed 01
3082023E 308201A7 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32383739 37393938 3738301E 170D3131 30343233 32303532
33345A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 38373937
39393837 3830819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100BE34 379A4D5D 1DA98B67 708AF8D4 221F1BE5 C5947EEA FF931EF4 37AD8A2C
C786C8D9 88E97474 D32FE0F0 10C048B9 6F5DA580 55241E61 9B0D849A D9E7182A
04D6C8E0 0C748DC7 0D8B4777 252CD4E1 01A1CEFC D57069CD C1B5E071 E591212D
80BE3A50 9062884E 57F4BF0C C0EFBF12 6509E384 E1196B8B 11C42280 80806D4B
F9290203 010001A3 66306430 0F060355 1D130101 FF040530 030101FF 30110603
551D1104 0A300882 06526F75 74657230 1F060355 1D230418 30168014 801FF21F
B68B4902 F183264C 381B00FF 31E04AD1 301D0603 551D0E04 16041480 1FF21FB6
8B4902F1 83264C38 1B00FF31 E04AD130 0D06092A 864886F7 0D010104 05000381
810072E2 23CBEABC B0D8ED1B 09835CAD 6D4D92C7 31880AF1 B9EC00DC 12DBDC2B
637FD4AB 39051AF3 04D3D948 180AB27A FFF66B33 6E44AB03 5280EC27 3C68C054
B365F6E3 5272D96F 9BBBC96E 228CC9C7 84F3CC48 28479B47 D8ADD129 7BF495FF
D8AFCA02 F8096B3C 581E68AA 16A00112 49FCED96 83DD2847 BA07F69D 9195248B EF31
quit
username INEM privilege 15 secret 5 $1$2Jgp$bV.OuBughjgSIOLuCr6Kn16FP.
archive
log config
hidekeys
controller DSL 0/0/0
mode atm
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
interface FastEthernet0/1
description Conection to CISCO SDM
ip address 10.10.10.1 255.255.255.248
ip tcp adjust-mss 1412
duplex auto
speed auto
interface ATM0/0/0
no ip address
no atm ilmi-keepalive
interface ATM0/0/0.1 point-to-point
pvc 0/35
pppoe-client dial-pool-number 1
interface Dialer0
ip address dhcp
ip mtu 1452
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname r353535
ppp chap password 0 xdfgdfg
ppp pap sent-username r353535 password 0 xdfgdfg
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
dialer-list 1 protocol ip permit
control-plane
line con 0
line aux 0
line vty 0 4
login
scheduler allocate 20000 1000
end
Some one can help me please?
thanks

Hello,
Can you explain me please the reason of my WIC 1SHDSL-v3 not work in ADSL lines ?
Thank you,
Best Regards

Configuring - Cisco 2921 with Switch Module/POE PS and 3750-x 24 port switch

Similar Messages

Maybe you are looking for