Configuring CWPulse and CWCounter with DAQ device

I am using VB with Measurement studio components and a DAQ E6024 card. I have set up a counter which is triggered by hardware at gate PFI9 and which uses an internal clock as a source. I then set up a pulse which will be generated on the GPCTR0_OUT line out of the counter once it has finished. When I configure both counter and pulse in the code, I get an error saying that two many controls are configured for this device and that I need to reset one of the controls before configuring any other controls. So how do I make sure all the properties are set without configuring both components? Many thanks in advance.

Greetings,
As this error indicates, a counter can not be configured for two operations at one time. So, you can assign the properties for CWCounter and CWPulse, call CWCounter.Configure, perform your counting operation, call CWCounter.Reset, and then call CWPulse.Configure. Since you want the counter to output a pulse when it finishes counting, you will need to reset CWCounter before you configure CWPulse.
Good luck with your application.
Spencer S.

Similar Messages

  • How to measure current and voltage and rpm with daq device

    i am measuring current and voltage and am wondering should i use shunt resistors or current sensors hall effect sensors. i have a pci 6221 and a scc-68 breakout box. what specifications or size should the shunt resistor/current sensor be or should i use another device to measure the currrent and voltage. do i need any other safety device between the resistors, current sensors and the scc-68 breakout box when measuring the current and voltage. will the daq card pci 6221 pick up a signal from the resistor. what terminals should the wires from the resistors and current sensors be connected to in the scc-68. i am using a proximity switch to measure rpm of a motor. should the proximity switch be 2 or 3wire connection. should it have an analog or digital connection and is a power supply required to power the proximity switch and should it have an npn or pnp connection

    hello,
     i was going to use a 20amp 50mv, or a 20amp 100mv current shunt and connect wires directly into the AI input terminals of the scc-68 from the current shunt would these be suitable. would current shunts such as these be suitable to use http://uk.farnell.com/elc/sh10020/shunt-sh10020-20a-100mv-1-class/dp/1319576 or http://uk.farnell.com/datel/3020-01098-0/shunt-50mv-20a/dp/1339338
    is it ok to use either a current shunt or should a hall effect sensor be used  such as this http://ie.farnell.com/honeywell-s-c/csla2cd/sensor-hall-effect/dp/1082269 . which of them would be more accurate or are both of them fairly accurate.
    when i am measuring voltage can i connect two resistors between the positive and negative of the wires going to the battery and connect two wires from either side of the resistor directly into the analog inputs of the scc-68 and measure the 12-15 volts directly would the pci6221 and scc-68 be able to measure the voltage drop across the resistor.
    i wanted to measure rpm also does it matter whether the proximity switch has 2 or 3 wires and should it have an analog or digital/frequency output for cponnecting to the scc-68

  • Which smart tv (SAMSUNG U46F7000 or SONY BRAVIA W8 46'') has the best communication and functionality with apple devices?

    Which SMARTTV (SAMSUNG U46F7000 or SONY BRAVIA W8 46'') has a better communication and functionality with apple devices (i pad- iphone).
    Since the above manufacturers do not give me a straight answer and it is very important reason for me to make a choice please advise!

    Sorry but I must correct about SONY!!!
    The question was for Bravia series W9 and not W8.

  • Any new  about updating lion to 10.7.4 and problems  with bluetooth devices  like Bose Soundlink Bluetooth Speaker?

    Any new  about updating lion to 10.7.4 and problems  with bluetooth devices  like Bose Soundlink Bluetooth Speaker?

    Monroe
    Just in the moment i updated to lion 10.7.4  my Bose Soundlink Bluetooth  stop working as  good as it was. I´m gonna try the update in the Bose  web page. I hope  it works

  • Losing communication with DAQ devices - help greatly appreciated

    All,
    I have been working on a VI whose function is the following:
    - Acquire data from three sources
         - A block of eight displacement sensors connected via RS232 (using a USB adapter)
         - An NI-USB 6210 card measuring voltages across eight batteries
         - Another NI-USB 6210 card measuring voltage across four load cells (these correspond to batteries one through four).
         - Data acquired at 1 Hz, written at 0.2 Hz (no buffer - simply writes one fifth of data recorded)
    - Open/close a relay board based on certain inputs
    - Provide basic UI functionality to control data manipulation, display data, and write data to text files
    - Write data to text files
    We have run four tests with this VI.  Each test runs for anywhere from 24 to 48 hours.  During three of these four tests, we have lost connection with one or both of our NI DAQ cards.  I have attached one of the output files - notice that in the 'Current (mA)/Voltage (V)' and 'Load (N)' columns, at a certain point on of the cards starts reading 'NaN', followed soon after by the other card.  Note that this has happened on two different computers, one laptop and one desktop, both of which had hibernate/sleep disabled.
    For your reference, I have attached the VI.  This VI will not run as there are some subVIs that I have not included; these subVIs do not do anything critical to the execution of the program.  The program generally runs as follows:
    - Initially, a subVI runs that aids the user in selecting the appropriate COM port and USB devices.
    - The VISA device and DAQ cards are initialized, all relays are opened, variables are initialized
    - In parallel, there are two producer timed loops, one consumer for loop and an event loop
         - One producer loop continuously acquires voltage data from both DAQ cards.  When the loop is over, basic DC voltage values are taken from all samples in each buffer, and the values are enqueued
         - One producer loop acquires one reading per loop from the displacement sensor (via a VISA Write -> VISA read), and the response string is enqueued.  
         - The consumer loop runs at a similar timing as the producer loops (blocked using queues).  It manipulates, displays, and records acquired data. It also opens relay channels if the corresponding displacement values are greater than a set threshold.
         - The event loop opens text files for writing when a button is depressed, as well as performing basic tasks such as clearing graphs, etc. 
    What is the cause of this issue?  What am I doing wrong?  This error is preventing us from running tests at our company.  Any help is greatly appreciated.
    Thank you,
    Bryan
    Attachments:
    DAQ issue VI.vi ‏124 KB
    sample output.txt ‏1230 KB

    Wayne,
    Thanks for your reply.  Unfortunately, my knowledge is limited in this area.  We are using an ADU208 USB relay from Ontrak (information here: http://www.ontrak.net/ADU208.htm).  We are using the bundled subVIs to open/close each channel of the relay depending on the acquired data.  How could this relay board affect the DAQ communication?  
    It may also be important to note - I have tried to make this VI so that all devices need not be used all of the time.  That is, sometimes we choose to not use the relay, sometimes we choose to not measure load, and sometimes we choose not to measure current.  This means that we do not always have the same hardware connected, but the software runs the same and deals with the resulting errors appropriately (hopefully).  The previously attached output file is from a test where the relay was not connected, however the relay commands were still run (and presumably threw errors).
    Thanks again for your help
    Bryan

  • HT4865 how do i turn off icloud sharing of my messages, and contacts with all devices on my account? I just want it to save each one individually

    i was on an account with itunes and icloud with my brother, but i got a new phone and a created a new ID for both. today my brother was getting copies of all my text on his iphone, and it then synced both our contacts to each others phone. Next me and my fiance share the new ID created and also today all the contacts that synced from my brothers phone to my phone then were merged with my fiances contacts!!! What is happening and how do we each create our own privacy without merging contacts, etc and still use the icloud backup feature?

    go to settings-icloud-delete account or turn of everything..

  • Issue with Linksys Router and Modem with Vonage Device

    Hello,
    I have a Linksys Router and Cable Modem.  Plus I have Vonage for my home phone.  I have been having several problems and now, my Vonage phone will not work at all.  I have cable internet and my ISP is Cox Commuication.  I do not know how to connect my Vonage device with my Router and Modem.  People have been giving me advice, but nothing has worked.
    Does anyone know how to intergrate all three of these items together?  Basically which plug goes where.  Currently my phone is not working.  The only thing that is in use right now is my linksys cable modem.  I have the power cord plugged in, the blue cord from the modem plugged into my laptop, and the cable from the modem to the wall jack.  Please help.  Thank-You!
    Linksys Router:  WRT54G version 6
    Linksys Cable Modem:  BEFCMU10
    Vonage (Motorola):  VT2143-VD
    Message Edited by preshe79 on 03-16-2008 03:56 PM
    Message Edited by preshe79 on 03-16-2008 03:58 PM

    The router should be online first. Can you get into the router's configuration page?
    The box said windows xp or better... So I installed Linux!

  • Configuring JMS and loadbalancer with SSL termination? Has Anyone done it?

    Hi all,
    I'm having a problem getting JMS or even any JNDI lookup to work with a hardware load balancer and SSL termination. Has anyone used such a configuration? The load balancer in question is a Cisco CSS 11500 Series which has an SSL module. A client communicates with the CSS over SSL, the SSL module decrypts the packets and sends it for content switching and on to WebLogic as cleartext.
    Without SSL termination everthing works fine. With SSL termination active, Web service and web content all work fine, but I can't get SSL tGetting Initial context from ms01
    <29-Sep-2006 16:07:22 o'clock IST> <Debug> <TLS> <000000> <SSL/Domestic license found>
    <29-Sep-2006 16:07:22 o'clock IST> <Debug> <TLS> <000000> <Not in server, Certicom SSL license found>
    <29-Sep-2006 16:07:23 o'clock IST> <Debug> <TLS> <000000> <SSL Session TTL :90000>
    <29-Sep-2006 16:07:23 o'clock IST> <Debug> <TLS> <000000> <Trusted CA keystore: D:/eclipse/workspace/LoadBalancerTest/ssl/keystores/cssKeyS
    ore.keystore>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <Filtering JSSE SSLSocket>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <SSLIOContextTable.addContext(ctx): 886220>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <SSLSocket will NOT be Muxing>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <write SSL_20_RECORD>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <3941240 SSL3/TLS MAC>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <3941240 received HANDSHAKE>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: ServerHello>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <3941240 SSL3/TLS MAC>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <3941240 received HANDSHAKE>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: Certificate>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <validationCallback: validateErr = 0>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> < cert[0] = [
    Version: V3
    Subject: EMAILADDRESS="[email protected] ", CN=10.51.0.200, OU=Web Administration, O=Revenue Commissioners, L=Dublin, ST=Dublin,
    =IE
    Signature Algorithm: MD5withRSA, OID = 1.2.840.113549.1.1.4
    Key: SunJSSE RSA public key:
    public exponent:
    010001
    modulus:
    a8f60248 b87c5860 229b9044 a666a9ae 27eb488c 424d9e67 e7b9d6d0 c292f081
    cfa76c04 f3d89b28 1bf544f9 5de2b66d 576ebeca 5dc5ca8a fceead9a 52e2ce6c
    2b91afef e4da5071 49b8784c 12d7f5f3 99f76482 79efe1d8 0a24f664 4c8d6e9e
    b0bc63be 1faf8319 eeb23e8a 019b65b2 59dd086d 1b714d4c 01618804 66f416bb
    Validity: [From: Fri Sep 08 11:44:28 BST 2006,
                   To: Mon Sep 05 11:44:28 BST 2016]
    Issuer: CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE
    SerialNumber: [    0131]
    Certificate Extensions: 4
    [1]: ObjectId: 2.16.840.1.113730.1.13 Criticality=false
    Extension unknown: DER encoded OCTET string =
    0000: 04 1F 16 1D 4F 70 65 6E 53 53 4C 20 47 65 6E 65 ....OpenSSL Gene
    0010: 72 61 74 65 64 20 43 65 72 74 69 66 69 63 61 74 rated Certificat
    0020: 65 e
    [2]: ObjectId: 2.5.29.14 Criticality=false
    SubjectKeyIdentifier [
    KeyIdentifier [
    0000: 0E 6E 72 2E B1 3B B6 A3 59 79 5A C5 41 26 B7 B6 .nr..;..YyZ.A&..
    0010: A2 39 4C 73 .9Ls
    [3]: ObjectId: 2.5.29.35 Criticality=false
    AuthorityKeyIdentifier [
    KeyIdentifier [
    0000: D2 66 DD FC 06 C2 BC 7E 18 D5 64 38 AD 6E D0 0A .f........d8.n..
    0010: AA 97 05 0D ....
    [CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE]
    SerialNumber: [    00]
    [4]: ObjectId: 2.5.29.19 Criticality=false
    BasicConstraints:[
    CA:false
    PathLen: undefined
    Algorithm: [MD5withRSA]
    Signature:
    0000: 2C A0 0C 34 4E 0D CA 24 A5 C3 03 3A 71 A1 2D D3 ,..4N..$...:q.-.
    0010: 65 A2 FA EF C1 5D D4 4A 28 8C 1A 70 5F 92 73 5E e....].J(..p_.s^
    0020: 7B 13 D4 AE 36 A8 86 EA 60 7F A5 E3 86 6E 84 1F ....6...`....n..
    0030: 5E 5F 30 06 B4 AA 2E 5C A7 65 74 32 09 0A 91 14 ^_0....\.et2....
    ]>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> < cert[1] = [
    Version: V3
    Subject: CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE
    Signature Algorithm: MD5withRSA, OID = 1.2.840.113549.1.1.4
    Key: SunJSSE RSA public key:
    public exponent:
    010001
    modulus:
    bc61b29f a830c97a 7a76883e 1665a241 a68b891f 8e4167eb 62e578ac 9e342c3e
    53c9de8b e756634b e364010f 4d36c1c5 21a65b37 b64b4861 6f4dda29 b932191f
    Validity: [From: Mon May 31 15:22:15 BST 2004,
                   To: Thu May 29 15:22:15 BST 2014]
    Issuer: CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE
    SerialNumber: [    00]
    Certificate Extensions: 3
    [1]: ObjectId: 2.5.29.14 Criticality=false
    SubjectKeyIdentifier [
    KeyIdentifier [
    0000: D2 66 DD FC 06 C2 BC 7E 18 D5 64 38 AD 6E D0 0A .f........d8.n..
    0010: AA 97 05 0D ....
    [2]: ObjectId: 2.5.29.35 Criticality=false
    AuthorityKeyIdentifier [
    KeyIdentifier [
    0000: D2 66 DD FC 06 C2 BC 7E 18 D5 64 38 AD 6E D0 0A .f........d8.n..
    0010: AA 97 05 0D ....
    [CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE]
    SerialNumber: [    00]
    [3]: ObjectId: 2.5.29.19 Criticality=true
    BasicConstraints:[
    CA:true
    PathLen:2147483647
    Algorithm: [MD5withRSA]
    Signature:
    0000: 3C 64 7C 9E 0B 90 48 9D 70 74 06 80 7F 2C AF 73 <d....H.pt...,.s
    0010: 92 1C C3 39 DD C3 45 B6 A4 8E 11 27 8E 21 18 4B ...9..E....'.!.K
    0020: FD AA 31 5E 35 FC DF 9E 70 42 F4 65 5C DF 56 9A ..1^5...pB.e\.V.
    0030: DD 8C 6B B7 3B BE E5 A7 D5 4A 16 23 C1 91 07 CA ..k.;....J.#....
    ]>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <SSLTrustValidator returns: 0>
    <29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <Trust status (0): NONE>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <Performing hostname validation checks: 10.51.0.200>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <3941240 SSL3/TLS MAC>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <3941240 received HANDSHAKE>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: ServerHelloDone>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 134>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <write CHANGE_CIPHER_SPEC, offset = 0, length = 1>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 16>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <3941240 SSL3/TLS MAC>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <3941240 received CHANGE_CIPHER_SPEC>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <3941240 SSL3/TLS MAC>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <3941240 received HANDSHAKE>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: Finished>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 0>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 272>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <3445873 read(offset=0, length=2048)>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3941240 SSL3/TLS MAC>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3941240 received APPLICATION_DATA: databufferLen 0, contentLength 372>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3445873 read databufferLen 372>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3445873 read A returns 372>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 0>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 339>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3445873 read(offset=372, length=1676)>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <Filtering JSSE SSLSocket>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLIOContextTable.addContext(ctx): 6771926>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLSocket will NOT be Muxing>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 93>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 SSL3/TLS MAC>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 received HANDSHAKE>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: ServerHello>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 SSL3/TLS MAC>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 received CHANGE_CIPHER_SPEC>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 SSL3/TLS MAC>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 received HANDSHAKE>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: Finished>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write CHANGE_CIPHER_SPEC, offset = 0, length = 1>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 16>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 0>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 402>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 0>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 1707>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <23328673 read(offset=0, length=2048)>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 SSL3/TLS MAC>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 received APPLICATION_DATA: databufferLen 0, contentLength 174>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <23328673 read databufferLen 174>
    <29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <23328673 read A returns 174>
    <29-Sep-2006 16:07:44 o'clock IST> <Debug> <TLS> <000000> <NEW ALERT with Severity: WARNING, Type: 0
    java.lang.Exception: New alert stack
    at com.certicom.tls.record.alert.Alert.<init>(Unknown Source)
    at com.certicom.tls.interfaceimpl.TLSConnectionImpl.closeWriteHandler(Unknown Source)
    at com.certicom.tls.interfaceimpl.TLSConnectionImpl.close(Unknown Source)
    at javax.net.ssl.impl.SSLSocketImpl.close(Unknown Source)
    at weblogic.net.http.HttpClient.closeServer(HttpClient.java:466)
    at weblogic.net.http.KeepAliveCache$1.run(KeepAliveCache.java:120)
    at java.util.TimerThread.mainLoop(Unknown Source)
    at java.util.TimerThread.run(Unknown Source)
    >
    <29-Sep-2006 16:07:44 o'clock IST> <Debug> <TLS> <000000> <avalable(): 23328673 : 0 + 0 = 0>
    <29-Sep-2006 16:07:44 o'clock IST> <Debug> <TLS> <000000> <write ALERT, offset = 0, length = 2>
    <29-Sep-2006 16:07:44 o'clock IST> <Debug> <TLS> <000000> <SSLIOContextTable.removeContext(ctx): 6771926>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <3941240 SSL3/TLS MAC>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <3941240 received APPLICATION_DATA: databufferLen 0, contentLength 98>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <3445873 read databufferLen 98>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <3445873 read A returns 98>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <Filtering JSSE SSLSocket>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLIOContextTable.addContext(ctx): 8406772>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLSocket will NOT be Muxing>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 93>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <21830977 SSL3/TLS MAC>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <21830977 received HANDSHAKE>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: ServerHello>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <21830977 SSL3/TLS MAC>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <21830977 received CHANGE_CIPHER_SPEC>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <21830977 SSL3/TLS MAC>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <21830977 received HANDSHAKE>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: Finished>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <write CHANGE_CIPHER_SPEC, offset = 0, length = 1>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 16>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 0>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 339>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <5618579 read(offset=0, length=2048)>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    Exception in thread "main" javax.naming.CommunicationException [Root exception is java.net.ConnectException: https://10.51.0.200:8143: Boot
    trap to: 10.51.0.200/10.51.0.200:8143' over: 'https' got an error or timed out]
    at weblogic.jndi.internal.ExceptionTranslator.toNamingException(ExceptionTranslator.java:47)
    at weblogic.jndi.WLInitialContextFactoryDelegate.toNamingException(WLInitialContextFactoryDelegate.java:636)
    at weblogic.jndi.WLInitialContextFactoryDelegate.getInitialContext(WLInitialContextFactoryDelegate.java:306)
    at weblogic.jndi.WLInitialContextFactoryDelegate.getInitialContext(WLInitialContextFactoryDelegate.java:239)
    at weblogic.jndi.WLInitialContextFactory.getInitialContext(WLInitialContextFactory.java:135)
    at javax.naming.spi.NamingManager.getInitialContext(Unknown Source)
    at javax.naming.InitialContext.getDefaultInitCtx(Unknown Source)
    at javax.naming.InitialContext.init(Unknown Source)
    at javax.naming.InitialContext.<init>(Unknown Source)
    at TestAllManagedServers.main(TestAllManagedServers.java:54)
    Caused by: java.net.ConnectException: https://10.51.0.200:8143: Bootstrap to: 10.51.0.200/10.51.0.200:8143' over: 'https' got an error or t
    med out
    at weblogic.rjvm.RJVMFinder.findOrCreate(RJVMFinder.java:200)
    at weblogic.rjvm.ServerURL.findOrCreateRJVM(ServerURL.java:125)
    at weblogic.jndi.WLInitialContextFactoryDelegate.getInitialContext(WLInitialContextFactoryDelegate.java:296)
    ... 7 more
    o work for a simple JNDI lookup. With SSL debugging turned on, the following output is given:
    When I compare the Server HTTP logs I see that an initial context lookup involves 3 HTTP requests, e.g.
    25.2.1.210 - - [29/Sep/2006:16:29:12 +0100] "GET /bea_wls_internal/HTTPClntLogin/a.tun?wl-login=https+dummy+WLREQS+8.1.5+dummy+%0A&r
    and=3018901804201457976&AS=255&HL=19 HTTP/1.1" 200 17
    25.2.1.210 - - [29/Sep/2006:16:29:12 +0100] "GET /bea_wls_internal/HTTPClntRecv/a.tun?connectionID=0&rand=7332722597180897050 HTTP/1
    .1" 200 2341
    25.2.1.210 - - [29/Sep/2006:16:29:12 +0100] "POST /bea_wls_internal/HTTPClntSend/a.tun?connectionID=0&rand=3415396992694182025 HTTP/
    1.1" 200 17
    When my request goes through the load balancer I see the following in the HTTP logs:
    10.51.0.200 - - [29/Sep/2006:16:31:33 +0100] "GET /bea_wls_internal/HTTPClntLogin/a.tun?wl-login=https+dummy+WLREQS+8.1.5+dummy+%0A&
    rand=8279752507152372405&AS=255&HL=19 HTTP/1.1" 200 17
    10.51.0.200 - - [29/Sep/2006:16:31:33 +0100] "POST /bea_wls_internal/HTTPClntSend/a.tun?connectionID=0&rand=1051450669479197885 HTTP
    /1.1" 200 17
    10.51.0.200 - - [29/Sep/2006:16:32:28 +0100] "GET /bea_wls_internal/HTTPClntRecv/a.tun?connectionID=0&rand=6035654607615870287 HTTP/
    1.1" 200 5
    10.51.0.200 - - [29/Sep/2006:16:33:13 +0100] "GET /bea_wls_internal/HTTPClntRecv/a.tun?connectionID=0&rand=8245112057388607005 HTTP/
    1.1" 200 5
    Notice the time delay in some of the messages.
    The following error appears in the WebLogic server log, however I've verified that all IP addresses referenced by the load balancer configuration match those in the WebLogic configuration:
    <29-Sep-2006 16:31:43 o'clock IST> <Error> <RJVM> <BEA-000572> <The server rejected a connection attempt JVMMessage from: '266014296
    868812899C:25.2.1.210R:2462711729186814398S:10.51.0.2:[8113,8113,8114,8114,8113,8114,-1,0,0]:10.51.0.1:8103,10.51.0.1:8105,10.51.0.1
    :8107,10.51.0.2:8109,10.51.0.2:8111,10.51.0.2:8113:risIntCluster01:ms06' to: '0S:10.51.0.200:[-1,-1,-1,8143,-1,-1,-1,-1,-1]' cmd: 'C
    MD_IDENTIFY_REQUEST', QOS: '102', responseId: '0', invokableId: '0', flags: 'JVMIDs Sent, TX Context Not Sent', abbrev offset: '228'
    probably due to an incorrect firewall configuration or admin command.>
    When a JNDI lookup is made directly to a WebLogic server on the https port, the client gives the following output:
    Getting Initial context from ms01
    <29-Sep-2006 16:29:22 o'clock IST> <Debug> <TLS> <000000> <SSL/Domestic license found>
    <29-Sep-2006 16:29:22 o'clock IST> <Debug> <TLS> <000000> <Not in server, Certicom SSL license found>
    <29-Sep-2006 16:29:23 o'clock IST> <Debug> <TLS> <000000> <SSL Session TTL :90000>
    <29-Sep-2006 16:29:23 o'clock IST> <Debug> <TLS> <000000> <Trusted CA keystore: D:/eclipse/workspace/LoadBalancerTest/ssl/keystores/cssKeySt
    ore.keystore>
    <29-Sep-2006 16:29:23 o'clock IST> <Debug> <TLS> <000000> <Filtering JSSE SSLSocket>
    <29-Sep-2006 16:29:23 o'clock IST> <Debug> <TLS> <000000> <SSLIOContextTable.addContext(ctx): 7860099>
    <29-Sep-2006 16:29:23 o'clock IST> <Debug> <TLS> <000000> <SSLSocket will NOT be Muxing>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <write SSL_20_RECORD>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <32915800 SSL3/TLS MAC>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <32915800 received HANDSHAKE>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: ServerHello>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <32915800 SSL3/TLS MAC>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <32915800 received HANDSHAKE>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: Certificate>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <validationCallback: validateErr = 0>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> < cert[0] = [
    Version: V3
    Subject: CN=10.52.0.3, OU=Revenue Integration Server, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE
    Signature Algorithm: MD5withRSA, OID = 1.2.840.113549.1.1.4
    Key: SunJSSE RSA public key:
    public exponent:
    010001
    modulus:
    ac47cae5 45e55fe4 8ec06362 84aab923 af35d7f1 8b7e8aaa 32772d8a d8185106
    0ba91363 07162207 6eaa33b4 db8a3fbb 1e228e93 841ff322 e319242a 04ae7447
    Validity: [From: Mon May 31 16:45:21 BST 2004,
                   To: Thu May 29 16:45:21 BST 2014]
    Issuer: CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE
    SerialNumber: [    05]
    Certificate Extensions: 4
    [1]: ObjectId: 2.16.840.1.113730.1.13 Criticality=false
    Extension unknown: DER encoded OCTET string =
    0000: 04 1F 16 1D 4F 70 65 6E 53 53 4C 20 47 65 6E 65 ....OpenSSL Gene
    0010: 72 61 74 65 64 20 43 65 72 74 69 66 69 63 61 74 rated Certificat
    0020: 65 e
    [2]: ObjectId: 2.5.29.14 Criticality=false
    SubjectKeyIdentifier [
    KeyIdentifier [
    0000: D7 B3 92 7B C7 4E 2F 5D F3 97 CB 3B F9 FB 0A 1E .....N/]...;....
    0010: 97 C5 DD F1 ....
    [3]: ObjectId: 2.5.29.35 Criticality=false
    AuthorityKeyIdentifier [
    KeyIdentifier [
    0000: D2 66 DD FC 06 C2 BC 7E 18 D5 64 38 AD 6E D0 0A .f........d8.n..
    0010: AA 97 05 0D ....
    [CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE]
    SerialNumber: [    00]
    [4]: ObjectId: 2.5.29.19 Criticality=false
    BasicConstraints:[
    CA:false
    PathLen: undefined
    Algorithm: [MD5withRSA]
    Signature:
    0000: 57 B6 54 4E 1A 54 91 66 5C A8 FE AF B6 50 AB 23 W.TN.T.f\....P.#
    0010: 6A 32 42 77 06 44 D5 7D 40 81 E4 DD 84 E3 7B 55 [email protected]
    0020: 96 A6 BC E9 E9 51 96 B9 E4 01 56 F9 41 B7 0C C3 .....Q....V.A...
    0030: 0A 92 C0 17 6E 6B 9D D6 9A 87 6D 6E 15 5A 86 F4 ....nk....mn.Z..
    ]>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> < cert[1] = [
    Version: V3
    Subject: CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE
    Signature Algorithm: MD5withRSA, OID = 1.2.840.113549.1.1.4
    Key: SunJSSE RSA public key:
    public exponent:
    010001
    modulus:
    bc61b29f a830c97a 7a76883e 1665a241 a68b891f 8e4167eb 62e578ac 9e342c3e
    53c9de8b e756634b e364010f 4d36c1c5 21a65b37 b64b4861 6f4dda29 b932191f
    Validity: [From: Mon May 31 15:22:15 BST 2004,
                   To: Thu May 29 15:22:15 BST 2014]
    Issuer: CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE
    SerialNumber: [    00]
    Certificate Extensions: 3
    [1]: ObjectId: 2.5.29.14 Criticality=false
    SubjectKeyIdentifier [
    KeyIdentifier [
    0000: D2 66 DD FC 06 C2 BC 7E 18 D5 64 38 AD 6E D0 0A .f........d8.n..
    0010: AA 97 05 0D ....
    [2]: ObjectId: 2.5.29.35 Criticality=false
    AuthorityKeyIdentifier [
    KeyIdentifier [
    0000: D2 66 DD FC 06 C2 BC 7E 18 D5 64 38 AD 6E D0 0A .f........d8.n..
    0010: AA 97 05 0D ....
    [CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE]
    SerialNumber: [    00]
    [3]: ObjectId: 2.5.29.19 Criticality=true
    BasicConstraints:[
    CA:true
    PathLen:2147483647
    Algorithm: [MD5withRSA]
    Signature:
    0000: 3C 64 7C 9E 0B 90 48 9D 70 74 06 80 7F 2C AF 73 <d....H.pt...,.s
    0010: 92 1C C3 39 DD C3 45 B6 A4 8E 11 27 8E 21 18 4B ...9..E....'.!.K
    0020: FD AA 31 5E 35 FC DF 9E 70 42 F4 65 5C DF 56 9A ..1^5...pB.e\.V.
    0030: DD 8C 6B B7 3B BE E5 A7 D5 4A 16 23 C1 91 07 CA ..k.;....J.#....
    ]>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <SSLTrustValidator returns: 0>
    <29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <Trust status (0): NONE>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <Performing hostname validation checks: 10.51.0.1>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <32915800 SSL3/TLS MAC>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <32915800 received HANDSHAKE>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: ServerHelloDone>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 70>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <write CHANGE_CIPHER_SPEC, offset = 0, length = 1>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 16>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <32915800 SSL3/TLS MAC>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <32915800 received CHANGE_CIPHER_SPEC>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <32915800 SSL3/TLS MAC>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <32915800 received HANDSHAKE>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: Finished>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 0>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 270>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <30340343 read(offset=0, length=2048)>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <32915800 SSL3/TLS MAC>
    <29-Sep-2006 16:29:28 o'clock IST> <Debug> <TL

    You will need an AAM set with the internal (http) address.
    http://blogs.msdn.com/b/ajithas/archive/2009/09/11/alternate-access-mapping-in-reverse-proxy-configuration.aspx
    Dimitri Ayrapetov (MCSE: SharePoint)

  • Nokia Configuration Tool and E70 with new firmware...

    After the firmware update with NSU an interesting problem appeared - every attempt to import or load the profile from the phone to application fails with error message stating that the connection was lost. No difference whether to use USB or bluetooth connection. Because all was fine before the update, the alleged Nokia statement about the USB port problems on many computers (found on some S60-related blog) cannot be taken seriously.
    It seems like the Configuration Tool is now also needing some update for compatibility with 3.06330.09.04 firmware
    P.S. However the program is not completely unusable - I managed to load the e-mail and SIP server settings to the phone without problems.
    388 -> 688 -> 6150 -> 6310 -> 6310i+1100+ E70-1(3.0633.09.04/crippled VoIP)

    ...have to take back this P.S. on previous message - too bad there's no way to edit the thread openings (replies are editable however)
    388 -> 688 -> 6150 -> 6310 -> 6310i+1100+ E70-1(3.0633.09.04/crippled VoIP)

  • Help! My photos won't stream to the cloud and share with other devices. ( I've had the photo stream button on all the time I've had the phone.) The only way I can do it is by manually adding them to photo stream and this is very slow/ misses photos..

    Hello,
    I'm very frustrated. I need to delete photos from my iphone to increase the storage so I can update the operating system. Since first using the phone I bought extra iCloud storage and ensured the photo streaming button for the iCloud was turned on.
    Unfortunately it seems to have a mind of its own and will download and share some photos but the majority have not been downloaded.
    I've resorted to manually putting them on photo stream (the one you share with friends) so the photos will be on my iPad. It also takes ages for my iphone to put them on the photo stream. It's downloaded one album x3 ..??!!? I've tried deleting the duplicated photos but it's now frozen on me....
    I haven't dared delete the photos from my camera roll in case I loose them all and I'm therefore stuck in the situation of being unable to download the new operating system or take anymore photos/download music/apps. It *****!
    Please Help!
    Are there any other options for me to be able to  download my photos when I don't have a computer/laptop? Is there a permanent online storage option I can use?
    Thanks
    Becky

    Amazing steps you've done so far! The great news is this is very unlikely an issue with your iPhone.
    I've run into a similar issue lately as well. I narrowed it down to one song that was causing 30 songs not to sync. I removed the song from the sync list (unchecked it) and all 29 songs were able to sync.
    You may be running into a similar issue. This may be a problem with this version of iTunes, an issue with one song or a group of songs; hard to know for sure. It's important to narrow down and isolate the cause. Most imporantly get that music back on there!
    The way to narrow down the casue add just a few songs at a time (even 1, just to get that first sync finished). Manually syncing is what you'll need here.
    Plug in your iPhone, on the Summary screen (shows a picture of your iPhone, the iOS version, Restore iPhone....; etc). Under the Options area at the bottom choose to Manually Manage Videos and Music then choose Apply in the lower right. The music that's on your iPhone now should be removed from your iPhone now. You're now able to sync music manually.
    The link below explains how to drag the songs from the iTunes library on the computer on to your iPhone which will start the sync. Add just one song just to see if you can get 1 of those hundreds of songs on there. If you can, awesome! Keep adding until you find the song or group of songs that are causing this issue.
    http://support.apple.com/kb/HT1535
    Please let me know how things are going.
    Cheers!

  • HT5569 my wifi will not connect to my iphone, the wifi device is on and working with other devices. The wifi on my phone will not even turn on it just says off please help me to connect thanks

    please help with the above question

    Is the wifi optoin greyed out? If so, go to Settings>General>Reset and reset nerwork settings. You will need to reenter any wifi passwords you had previously saved. If that dosn't work, backup the phone and restore it http://support.apple.com/kb/ht1766 this will walk you through all that. Just make sure you setup your phone as new and test the wifi before restoring from backup.

  • How to configure gauge and slider with VC

    Hi All
    I have a iview in the VC Model and in the iview I have a query which generates Inventory Qty. I put a form in this iview and put a gauge on ithe form.
    I connected the query inv qty to the form but I cannot set the gauge to display the inv qty.
    I cannot find any documentaiton on this something like a step by step on using gauges, sliders and traffic lights.
    Can you please let me know how I can get the gauge to display the inv qty. Also how do I use the slider and traffc lights.
    Thanks n advance
    Karen

    Hi Karen,
    Maybe you didn't search in the right place.  Lets start with SAP Help and SDN Wiki
    http://help.sap.com/saphelp_nw04s/helpdata/en/47/78bdc557fc199ae10000000a42189d/frameset.htm
    http://wiki.sdn.sap.com/wiki/display/VC/Modeling
    Hope it helps.
    Dao

  • Simulation PID on control and design with DAQ card how to connection

    hi guys.. i am a beginner for LabVIEW 
    i have homework design PID on simulation path and i found by google
    how to connect simulation path to DAQ card ??
    anybody can help me
    which function to connect it???

    Duplicate Post

  • Annoying popping and clicking with Realtek devices/drivers

    anybody out there with an HP pavilion notebook with the realtek audio hardware and software? I just bought this system on Aug 21 2008 and have uninstalled and reinstalled the most up-to-date drivers, etc and sporadically yet continuously get popping and clicking sounds whenever i play movies or music files in itunes or quicktime. i'm using Windows Vista Home Premium OS and ensured everything is up-to-date with Microsoft products and no luck. Very frustrated!!

    I just updated to 8.0.2.20 and now everything I plays skips and sounds like an old scratched LP record (remember those???).
    This is not related to equalizer settings or hardware settings or anything else... you have people who have been using iTunes just fine until version 8 then all of a sudden massive problems... there are dozens and dozens of posts about this problem now. It has nothing to do with any settings, as people have been fine with prior versions, the common thread is that they've all upgraded to version 8.
    And you shouldn't have to stop using equalization or change anything you had before either.
    This is a BUG in VERSION 8. It seems that this version is full of bugs from what I have read across the internet-- has Apple started finally releasing crappy software? (It is inevitable). Maybe this is from outsourcing all the coding to countries where English is not the native language-- who knows.
    In any event, before I updated (from an earlier version of 8) I noticed Itunes stopped playing any sound at all. After I updated it gave me the error message telling me I had to delete/re-install quicktime. I did and now the clicking and popping. I re-installed/repaired directly from the website. Still nothing.
    My music plays perfectly from any other application. This is an iTunes BUG in VERSION 8.
    Also, as others have noticed new oddities in the way itunes behaves in version 8. Some have tremendous CPU usage or problems with internet. My hard drive rattles and buzzes whenever I start iTunes!!!! That scares the h*ll out of me! No other app does this and I can load all my music with any other app just fine-- no buzzing of the hard drive.
    I'm running a new machine with max'd RAM, 2 TB of drives hooked into a Windows Home Server with 9TB of music and video. I'll try rebuilding the library... but darn it how come no other problems with any other app? Media Monkey plays everything fine, for exmaple. Gotta be iTunes.

  • FMLE and 50fps with BlackMagic devices

    FMLE seems to be missing the possibility for 50fps There is a 60, 59.94, 30...fps setting - no 50 fps.
    BM settings (fx DeskLinDuo or Intensity Shuttle) allow me to choose 720p50 - but it is reset to 59.94 every time.
    25fps doesn't work either.
    Must be a missing setting in FMLE. Can't find it with a webcam either.
    How can I fix that?
    Thank You
    Frank

    Seems, FMLE doesnot support Europe 50fps standart at all. Neither 1080i/50 (work when capturing 25fps) nor 720p/50. I'm using Canon XHG1 cameras, which can produce only 1080i/50 fps and JVCs ProHD 251 whis are 720p/50.
    The solution is to use osprey 700 HD capture card, which can hardware reencode to desireable screen size and bitrate (I'm able to stream 720p/50 feed to 720p/25 encoded stream). But they are too expensive.
    With DeckLink SDI capture cards I can only stream 1080i/50 feed capturing 1080i/25 fps (somehow, this encoding preset works). But I have to software deinterlace, so picture quality degrades.
    PS: When I'm using Canon XHG1s, I want to cross convert 1080i/50 feed with blackmagic updowncross mini converter to more affordable 720p/50 feed, which have no deinterlace nightmare.. But this stream I can't capture and stream.
    There is no problems with "NTSC" cameras - 60/30 fps.

Maybe you are looking for

  • BW/HR structural authorization in BI 7.0 version

    Dear experts, Can anyone please explain how to extract HR structural authorization from R/3 to BW 7.0, and how to configure the authorization in the BW, I hope everyone can give me a work flow. Thanks.

  • When asking for username and password the default username is wrong

    I have had a look through all the posts here but I can't find anything that helps me. I don't want to actually change my username or reset my password. I know what they both are; however... I have a recently had to replace my hard drive and now have

  • Graphics and anchored frames

    My EDD is set up to insert anchored frames as I import a graphic by reference. The default position is centre aligned. I would like to change this to left aligned. Then I would like to be able to set up a fixed alignment offset on the graphic. At pre

  • Source system connection problem

    Hi Gurus, Data was loading from r3 to BI. But while loading, the job in the source system got cancelled in R3 with error, Job also cancelled due to process termination. See the system log. When I checked for the connection test of the source system I

  • Which version of MAC OS do I need?

    I have a MacBook Pro with a blank hard drive, which version of Mac OS do I need for a new full install? I've never used a Mac before so I'm a bit lost on which one I need to buy Thanks