Configuring dedicated/shared mode with DBCA wizard

Hello,
I've tried to configure several instances with DBCA wizard, both in dedicated and shared mode :
- when dedicated mode is selected, dispatchers parameter is set like this : "dispatchers=(PROTOCOL=TCP) (SERVICE=sidXDB)", and all connections at the instance will be in by default dedicated mode, even if the "shared_servers" parameters is greater than 0
- when shared mode is selected, dispatchers parameter is set like this : "dispatchers=(PROTOCOL=TCP)"
I thought that the instance would run automatically in shared mode if the "shared_servers" parameters is greater than 0, but that's untrue
Besides, I don't understand the link between the "(SERVICE=sidXDB)" option, which seems to be related to the XML database, and the connection mode to the instance.
This is quiet confusing to me, there is obviously something I don't know or I don't understand
Can anyone make it clear to a Oracle beginner ?
Thank you for help !
regards,
Antoine

SHARED_SERVERS alone is not enough, it needs a corresponding dispatchers setting, something like 'dispatchers=(PROTOCOL=TCP)'. By default during a 10g database creation a XML DB is configured and 'dispatchers=(PROTOCOL=TCP) (SERVICE=sidXDB)' is dedicated to this XML DB, this dispatcher cannot serve any other database service. That means normal database connections are created as dedicated ones.
Werner

Similar Messages

ASA 5510 context base configuration in HA Mode with two different subnet

Hi
Please someone help me to configure the Firewall ASA 5510 in context based configuration in HA Mode with two different subnet....
IP Details are below.....:
interface Ethernet0/0
nameif outside
security-level 0
ip address 10.10.10.2 255.255.255.0 standby 10.10.10.3
interface Ethernet0/1
no nameif
security-level 0
no ip address
interface Ethernet0/1.101
description INSIDE1
vlan 101
nameif INSIDE1
security-level 90
ip address 172.22.0.2 255.255.255.0 standby 172.22.0.3
interface Ethernet0/1.102
description INSIDE2
vlan 102
nameif INSIDE2
security-level 80
ip address 172.22.1.2 255.255.255.0 standby 172.22.1.3
interface Ethernet0/3
description LAN Failover Interface
failover
failover lan unit primary
failover lan interface FAILOVER Ethernet0/3
failover replication http
failover interface ip FAILOVER 192.168.3.1 255.255.255.0 standby 192.168.3.2
route outside 0.0.0.0 0.0.0.0 10.10.10.1 1

Hi Sanjeev,
If it is a context based configuration that you are doing then, you would need to configure context on the ASA first, you can refer to this document for it:
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00808d2b63.shtml
Thanks,
Varun Rao
Security Team,
Cisco TAC

Dedicated/shared mode

Dear all,
How to ensure that my database is running in dedicated or shared server mode.
Thanks in advance

I'll just summarise, because I can see some rather iffy advice being offered in this thread.
If you are running in 9i or above, there are two parameters (not one) which govern whether or not you are capable of running in shared server mode.
DISPATCHERS governs whether a job dispatcher runs. You have to have at least one of them configured before shared server is possible. However, the mere fact that a dispatcher runs does NOT mean your database is running in shared server mode. There also have to be shared server processes capable of handling the work dispatched by the dispatcher(s), and those are configured with the SHARED_SERVERS parameter. If that's set to any number greater than 1, you have shared server processes running on your instance. But that STILL doesn't mean you're running in shared server mode! If you have SHARED_SERVERS=57 and no dispatcher, you simply have 57 processes sitting around doing nothing whatsoever (and incapable of doing useful work!)
In short, you have to have DISPATCHERS and SHARED_SERVERS set.
Note, for example, that 10g configures a single dispatcher for all databases by default (if they're created with DBCA and you don't get in there to stop it happeneing), but it does NOT configure SHARED_SERVERS, so by default a 10g database does not run in shared server mode.
The other thing I'd clarify is that a database doesn't really run in shared server mode anyway! The fact that your instance has a dispatcher and shared server processes running doesn't necessarily mean your users will end up connected to the dispatcher and having shared server processes handling their job requests. They will by default, but if the tnsnames.ora they use to connect (or its centralised equivalent) contains the line SERVER=DEDICATED, then they will get to use dedicated server processes, no matter what the dispatcher or shared server processes might think about it!
With dispatchers and shared server processes configured, in other words, an instance can "support shared server connection requests". That's rather different than "running in shared server mode". The distinction is important because privileged actions (startup, shutdown, backup and recover commands) cannot be processed by a shared server process, so it's important for an instance that is configured for normal users to use shared server processes to still support the connection to dedicated server processes by suitably credentialled users.
If a user does end up connected to a shared server process, there is usually a performance penalty to pay compared to using a dedicated server process. A user submits a query and instead of it being immediately processed by a server process, it gets submitted to a dispatcher ...which promptly sticks it on a job queue! You then have to wait for a shared server process to become free and decide to pick your job off the queue. That's inevitably slower than doing it the dedicated way.
People use shared server as the first line of scaling up their databases... and you're right that it primarily depends on the number of users connected to the server concurrently. In dedicated server mode, a new connection means a new process gets spawned (or a new thread on Windows) and a new connection socket is opened. Servers can only handle so many connection sockets, processes or threads before they start to keel over under the strain. Shared server, as the name suggest, means that new connections do not cause new server processes to be spawned. So 300 users can be processed with, maybe, 30 or 40 processes in total. If your box would normally keel over handling 300 dedicated connections, then clearly with that sort of sharing ratio, you'd be able to scale to nearer 3000 users before it starts wilting by using shared processes.
But it's also a bit subtler than that: a data warehouse would be daft to implement shared server, even if it did have 300+ concurrent users. That's because the users of such systems typically run queries that run for hours... and a shared process that is nabbed to perform one job for hours on end isn't really a shared process any more, is it?! So the rule of thumb as to when to implement shared server is yes, (a) when your concurrent user count starts reaching levels that your server just doesn't seem able to sustain any more AND (b) when you can be sure that the users tend to issue short, sharp queries -say, about 3 seconds or so to process, max.
Again, there are mixed states to get through, too. You might have lots of OLTP-type sub-3-second transactions on the same database on which one or two users regularly run big reports. In that case, you make sure the reporters have a tnsnames.ora that says SERVER=DEDICATED and the OLTP-type people use one that has SERVER=SHARED in it; configure the DISPATCHERS and SHARED_SERVER parameters for the instance and then those that can benefit from shared servers can do so and those that wouldn't won't be stealing shared processes from those that can!
The alternative approach for those with more cash is to go and buy better server hardware that can cope with the user community numbers! Shared Server configuration, however, comes free. You pays your money and you takes your choices!

Troble configuring Hyperion Shared Services with SQL Server 2005

I recently installed SQL server (SQL SERVER 2005) in my machine and then am trying to install Hyperion (9.3.1) products. I started with Shared services. It was installed successfully. Problem is occuring when am trying to configure Shared service with SQL database using Hyperion Configuration utility (9.3.1)
The error which is popping up is
Unable to connect to the database for the product Hyperion Shared Services.
Things which I tried from my end
1. Made sure TCP IP Protocol was enabled in SQL server configuration server.
2. hypuser was created in SQl server.
3. hypdb was created in SQL server.
4. Was having dynamic IP address so install Loopback adapter to obtain Static IP address and port.
5. Port and IP address was correct.
Let me know where I am going wrong.
Any help will be greatly appreciated.

Finally got it fixed firewall settings needed to be change : This document helped me a lot to troubleshoot the issue
An error has occurred while establishing a connection to the server. When connecting to SQL Server 2005, this failure may be caused by the fact that under the default settings SQL Server does not allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 2)
This problem may occur when SQL Server 2005 is not configured to accept incoming local and remote connections, which is disabled by default in SQL Server 2005 Express Edition, SQL Server 2005 Developer Edition and also SQL Server 2005 Enterprise Edition. To solve the connection forbidden problem, SQL Server 2005 needs to configure to allow incoming local and remote connections.
Firstly, ensure that SQL Server 2005 is configured properly to allow incoming connections on the instance of database server, else enable and turn on the local and remote connections setting.
Click Start button, then go to Programs or All Programs, then select Microsoft SQL Server 2005, followed by Configuration Tools. Click and run the SQL Server Surface Area Configuration.
On the “SQL Server 2005 Surface Area Configuration” page, click Surface Area Configuration for Services and Connections.
On the “Surface Area Configuration for Services and Connections” page, expand Database Engine tree, click Remote Connections.
Select Local and remote connections, or Local connections only which applicable only if there is no remote system tries to connect to the SQL Server, useful when you just trying to connect and authenticate with the server after installing.
Select the appropriate protocol to enable to local and/or remote connections environment. To ensure maximum compatibility, select Using both TCP/IP and named pipes.
Click Apply button when done.
Click OK button when prompted with the message saying that “Changes to Connection Settings will not take effect until you restart the Database Engine service.”
On the “Surface Area Configuration for Services and Connections” page, expand Database Engine, then click Service.
Click Stop button to stop the SQL Server service.
Wait until the MSSQLSERVER service stops, and then click Start button to restart the MSSQLSERVER service.
Secondly, SQL Server Browser service has to be enabled to allow for local and remote connections if SQL Server 2005 is running by using an instance name and users are not using a specific TCP/IP port number in the connection string.
Click Start button, then go to Programs or All Programs, then select Microsoft SQL Server 2005, followed by Configuration Tools. Click and run the SQL Server Surface Area Configuration.
On the “SQL Server 2005 Surface Area Configuration” page, click Surface Area Configuration for Services and Connections.
On the “Surface Area Configuration for Services and Connections” page, click SQL Server Browser.
Select Automatic as the Startup type to start SQL Server Browser service automatically every time system starts.
Click Apply button.
Click on Start button to start the service immediately.
Click OK button.
Finally, if remote computer needs to connect and access SQL Server, an exceptions in Windows Firewall included in Windows XP SP2 (Service Pack 2), Windows Server 2003 and Windows Vista needs to be created. If you’re using third-party firewall system, the exception rules also needed to be created to allow external remote connections to the SQL Server 2005 and SQL Server Browser Service to communicate through the firewall, else connections will be blocked. Consult the firewall manual for more details. Each instance of SQL Server 2005 must have its own exception, together with an exclusion for SQL Server Browser service.
SQL Server 2005 uses an instance ID as part of the path when you install its program files. To create an exception for each instance of SQL Server, you must identify the correct instance ID. To obtain an instance ID, follow these steps:
Click Start button, then go to Programs or All Programs, then select Microsoft SQL Server 2005, followed by Configuration Tools. Click and run the SQL Server Configuration Manager.
In “SQL Server Configuration Manager”, click the SQL Server Browser service in the right pane, right-click the instance name in the main window, and then click Properties.
On the “SQL Server Browser Properties” page, click the Advanced tab, locate the instance ID in the property list.
Click OK button.
Then create an exception for SQL Server 2005 in Windows Firewall.
Click on Start button, the click on Run and type firewall.cpl, and then click OK. For Windows Vista, type firewall.cpl in Start Search box and press Enter key, then click on Allow a program through Windows Firewall link on left tasks pane.
In “Windows Firewall”, click the Exceptions tab, and then click Add Program.
In the “Add a Program” window, click Browse button.
Click the C:\Program Files\Microsoft SQL Server\MSSQL.1\MSSQL\Binn\sqlservr.exe executable program, click Open button. MSSQL.1 with is a placeholder for the instance ID that is obtained from previous procedure. Note that the path may be different depending on where SQL Server 2005 is installed.
Click OK button.
Repeat steps 1 through 5 for each instance of SQL Server 2005 that needs an exception.
For SQL Server Browser service, locate the C:\Program Files\Microsoft SQL Server\90\Shared\sqlbrowser.exe executable program, and click Open button.
Click OK button.

Error While Configuring the Shared Service with Active Directory

Hi All,
I am getting a error while configuring MSAD with Shared Service, when entering the User Id and password and clicking next, the following error is displayed:
"EPMCSS-05180:Failed to validate Security configuration. Failed to connect. Invalid values for Base DN, User DN or Password. Enter valid value(s). Root Cause : [LDAP: error code 49 - 80090308: LdapErr: DSID-0C0903A9, comment: AcceptSecurityContext error, data 52e, v1db1]"
The AD user has the read access to the all users and group in Active Directory. If I use an Active Directory user with Admin privilege, It is getting connected.
But client is not ready to provide the Admin Access due to their internal policy and I also don't have any document which says admin privilege is required. According to the document,the user should have the following privileges only.
"The distinguished name of the user that Shared Services should use to bind with the user directory. This user must have search privilege on the RDN attribute within the DN. For example, in the dn: cn=John Doe, ou=people, dc=myCompany, dc=com, the bind user should have search access to the cn attribute.Special characters in User DN must be specified using escape characters. See “Using Special Characters” on page 46 for restrictions.
Example: cn=admin,dc=myCompany,dc=com
But I am getting confused with the statement "This user must have search privilege on the RDN attribute within the DN". Is it not search privillege?
Can anybody help me with required privilege for Active Directory user to configure with Shared Service.
Thanks in Advance,
Sunil

Thank you All,
i tried connecting using AD Browser from Microsoft, and it went in properly. then i found out that the AD Team here were giving a Wrong Credentials to connect, they Gave me HYP_OID which infact turned out to be a Principal name instead of a 'cn'.
after searching in the AD Browser i found the correct cn which is "Hyperion OID", then it went to the second Screen where now i am trying to search for the Users based on thier Job Nature.
Thank you for all the Support Guys, you both "Celvin" and "John" are the Top Guys under my Search list for any technical Assistance.
Thank you once again Friends....
Regards,
Sunil...
Shantan....

Ace module in bridged mode with client nat

Could someone confirm whatever a NAT is supported for ACE-20 module, please?
Let me to explain technical details.
I do need to convert working CSM(SLB) config to ACE configuration and I am not quite sure
if the configuration below is correct. ACE module should be configured in bridge mode with two
vlans - vlan 36 (client) and vlan 436 (server) - bridged with interface bvi 36.
NAT on ACE configurad as "nat dynamic 1025 vlan 436" into corresponding
"policy-map type loadbalance"
Could you check two parts of configs and advise me if the ACE config is
properly converted from CSM and will be working in the same way (especialy for NAT).
Thank you in advance.
CSM config
=======
vlan 36 client
ip address 10.36.3.3 255.255.255.0 alt 10.36.3.4 255.255.255.0
gateway 10.36.3.1
vlan 436 server
ip address 10.36.3.3 255.255.255.0 alt 10.36.3.4 255.255.255.0
natpool WEB-MAIL 10.36.3.100 10.36.3.100 netmask 255.255.255.0
sticky 30 netmask 255.255.255.255 address source timeout 60
probe SHAREPOINT tcp
interval 30
failed 120
open 3
port 80
probe WEBMAIL-443 tcp
interval 5
failed 60
open 2
port 443
serverfarm WEBMAIL-443
nat server
nat client WEB-MAIL
predictor leastconns
real 10.36.3.101 443
   inservice
real 10.36.3.102 443
   inservice
probe WEBMAIL-443
serverfarm WEBMAIL-80
nat server
nat client WEB-MAIL
predictor leastconns
real 10.36.3.101 80
   inservice
real 10.36.3.102 80
   inservice
probe SHAREPOINT
vserver WEBMAIL-443
virtual 10.36.3.100 tcp https
serverfarm WEBMAIL-443
sticky 60 group 30
replicate csrp sticky
replicate csrp connection
persistent rebalance
inservice
vserver WEBMAIL-80
virtual 10.36.3.100 tcp www
serverfarm WEBMAIL-80
replicate csrp connection
persistent rebalance
inservice
ACE config
=======
probe tcp WEBMAIL-443
interval 5
open 2
passdetect interval 60
port 443
probe tcp SHAREPOINT
interval 30
open 3
passdetect interval 120
port 80
serverfarm host WEBMAIL-443
predictor leastconns
probe WEBMAIL-443
rserver 10-36-3-101 443
    inservice
rserver 10-36-3-102 443
    inservice
serverfarm host WEBMAIL-80
predictor leastconns
probe SHAREPOINT
rserver 10-36-3-101 80
    inservice
rserver 10-36-3-102 80
    inservice
class-map match-all WEBMAIL-80
match virtual-address 10.36.3.100 tcp eq www
class-map match-all WEBMAIL-443
match virtual-address 10.36.3.100 tcp eq https
sticky ip-netmask 255.255.255.255 address source 30
serverfarm WEBMAIL-443
replicate sticky
timeout 60
policy-map type loadbalance first-match WEBMAIL-80
class class-default
    serverfarm WEBMAIL-80
    nat dynamic 1025 vlan 436 serverfarm primary
policy-map type loadbalance first-match WEBMAIL-443
class class-default
    sticky-serverfarm 30
    nat dynamic 1025 vlan 436 serverfarm primary
parameter-map type http HTTP_ADV_OPT
persistence-rebalance
policy-map multi-match IFVLAN36-POLICY
class WEBMAIL-80
    appl-parameter http advanced-options HTTP_ADV_OPT
    loadbalance policy WEBMAIL-80
    loadbalance vip inservice
    loadbalance vip icmp-reply active
class WEBMAIL-443
    appl-parameter http advanced-options HTTP_ADV_OPT
    loadbalance policy WEBMAIL-443
    loadbalance vip inservice
    loadbalance vip icmp-reply active
interface vlan 36
bridge-group 36
service-policy input IFVLAN36-POLICY
mac-sticky enable
no shutdown
interface vlan 436
bridge-group 36
nat-pool 1025 10.36.3.100 10.36.3.100 netmask 255.255.255.0
no shutdown
interface bvi 36
ip address 10.36.3.3 255.255.255.0
peer ip address 10.36.3.4 255.255.255.0
no shutdown

Hello F.Makarenko-
You will want to use PAT while you do nat, so change the natpool configuration to this:
   nat-pool 1025 10.36.3.100 10.36.3.100 netmask 255.255.255.0 pat
You also need to apply the nat like this:
policy-map multi-match IFVLAN36-POLICY
class WEBMAIL-80
    appl-parameter http advanced-options HTTP_ADV_OPT
    loadbalance policy WEBMAIL-80
    loadbalance vip inservice
    loadbalance vip icmp-reply active
    nat dynamic 1025 vlan 436
class WEBMAIL-443
    appl-parameter http advanced-options HTTP_ADV_OPT
    loadbalance policy WEBMAIL-443
    loadbalance vip inservice
    loadbalance vip icmp-reply active
    nat dynamic 1025 vlan 436
If you are going to build out a lot of classes, you can instead do source nat like this:
policy-map multi-match IFVLAN36-POLICY
class WEBMAIL-80
    appl-parameter http advanced-options HTTP_ADV_OPT
    loadbalance policy WEBMAIL-80
    loadbalance vip inservice
    loadbalance vip icmp-reply active
class WEBMAIL-443
    appl-parameter http advanced-options HTTP_ADV_OPT
    loadbalance policy WEBMAIL-443
    loadbalance vip inservice
    loadbalance vip icmp-reply active
class class-default
    nat dynamic 1025 vlan 436
Regards,
Chris Higgins

Cisco 2960S Configured in Transparent mode

I have a Cisco 2960S gig switch configured in transparent mode with multiple vlans configured. I have printers that I can ping, the ports shows up but on the printer it says offline. Any idea what could be causing this?

If your printer and your PCs are all in the same subnet and only the printer is not working then VTP mode Transparent has nothing to do with your issue.
I'd be keen to know if you have a firewall blocking anything from the IP address of the printer? Maybe the IP subnet mask or default gateway of the printer is not working?
What do you get when you do a "sh mac-address interface <PRINTER port>"?

Shared and Dedicated server modes

Hi,
We have been having some issues with connections and listeners. Please find here... Link [Post1|http://forums.oracle.com/forums/message.jspa?messageID=3665455] and Link [Post2|http://forums.oracle.com/forums/message.jspa?messageID=3677914].
Despite this help from this forum, I still face some problem configuring listener in both Shared and Dedicated server modes.
Pls find the below the problem...
Two listeners namely, LSNR1 and LSNR2 have been started.
listener.ora:
LSNR2 =
(DESCRIPTION_LIST =
    (DESCRIPTION =
      (ADDRESS = (PROTOCOL = TCP)(HOST = dbdev.website.org)(PORT = 1522))
      (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC0))
SID_LIST_LSNR2 =
(SID_LIST =
    (SID_DESC =
      (SID_NAME = TESTDB)
      (ORACLE_HOME = /u02/app/oracle)
LSNR1 =
(DESCRIPTION_LIST =
    (DESCRIPTION =
      (ADDRESS = (PROTOCOL = TCP)(HOST = dbdev.website.org)(PORT = 1521))
      (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC0))
SID_LIST_LSNR1 =
(SID_LIST =
    (SID_DESC =
      (SID_NAME = TESTDB)
      (ORACLE_HOME = /u02/app/oracle)
)LSNR1 works with both Shared and Dedicated configurations, whereas LSNR2 neither DEDICATED nor SHARED configurations...
Here is the TNS names entry at the client (for LSNR2)...
serv2=
(DESCRIPTION =
    (ADDRESS_LIST =
      (ADDRESS = (PROTOCOL = TCP)(HOST = xxx.xxx.xxx.xxx)(PORT = 1522))
    (CONNECT_DATA =
      (SERVICE_NAME=DEDICATED)
)When I try to connect using this, it says
+ ORA-12514: TNS: Listener does not know of service requested in connect descriptor +
Pls help.
Thanks,
Aswin.

Aswin,
I didnt see the other posts but the error is fairly simple,
>
ORA-12514:
TNS:listener does not currently know of service requested in connect descriptor
Cause:     The listener received a request to establish a connection to a database or other service. The connect descriptor received by the listener specified a service name for a service (usually a database service) that either has not yet dynamically registered with the listener or has not been statically configured for the listener. This may be a temporary condition such as after the listener has started, but before the database instance has registered with the listener.
Action:
- Wait a moment and try to connect a second time.
- Check which services are currently known by the listener by executing: lsnrctl services <listener name>
- Check that the SERVICE_NAME parameter in the connect descriptor of the net service name used specifies a service known by the listener.
- If an easy connect naming connect identifier was used, check that the service name specified is a service known by the listener.
- Check for an event in the listener.log file.
>
So check what you are passing in the connection string.
HTH
Aman....

How to convert dedicated server-mode to shared server-mode ?

Hi
I am having 3 oracle client machines(each with sql*plus or Toad tool),all these 3 client are to be connected through Jboss-4.0.5(application server) to Oracle 10g database server.
[ all 3 clients + 1 application server + 1 database server are with different ip address]
Question-1
Is it possible to convert a running Oracle-10.1.0.2.0 database server in[b] Windows server-2003 os from dedicated server-mode to shared server-mode ?
Question-2
What all are the init parameters I have to change ?
So far I have changed (a) alter system set shared_servers=5;
(b) alter system set dispatchers=(pro=tcp)(dis=3);
(c) alter system set max_dispatchers=10;
(d) alter system set shared_server_sessions=5;
(e) alter system set circuits=300;
Question-3
How to configure Listener in the Client system ?
Question-4
What all are the changes to be made in Jboss server ?
Regards
Sbmk_design

ad 1) Yes this is possible
Ad 2) From the top of my head, these seem like the settings to change
Ad 3) You do not have to change the listener (ow.. and clients have no listener) just make sure that you do not have '"server=dedicated" in your local tnsnames.ora file
Ad 4) in jboss, just check your datasource. If it is using a thin connection you are ok, if you are using a oci connection check the tnsnames.ora file.

Error configuring shared services with Oracle 11g database

I've installed Hyperion EPM 11.1.1.3 and orale 11g successfully. My problem though is that when i tried to do the configuration,
the error message states 'Unable to check Shared Services database existence: an error occured.'
---------My Environment:--------
EPM Server: Windows Server 2003 SP1 32-bit
RDBMS: Oracle Enterprise Edition 11g (running on same server 2003)
Oracle Client: 11g (full client install)
SID name :- orcl
------------Here are the components that I've installed--------
- V17397-01(EPM Foundation Services p-1)
- V17369-01(EPM Foundation Services p-2)
- V17370-01(EPM Foundation Services p-3)
- V17371-01(EPM Foundation Services p-4)
- V17389-01(server)
- V17388-01(Client)
- V17390-01(Provider Service)
- V17378-01(Financial Reporting)
- V17380-01(Web Analysis)
- V17398-01(EPM Architect)
- V17402-01(Smart View for Office)
all files are extracted in a single folder using winrar tool.
I can't proceed with the shared services configuration because in just the first page of it, I'm encountering the error Unable to check Shared Services database existence: an error occured.'
I believed the shared services is bundled with the foundation if I'm not mistaken, because I can't find any download related to it on edelivery site.
I tried to configure only the Foundation components but the '*Comman setting*' & '*configure database*' are grayed out so I have no option but to figure out first this shared services configuration.
below are the logs
---------------configtool.log--------------
(Jul 04, 2010, 02:53:29 AM), com.hyperion.config.wizard.impl.RegistryWizardState$1, DEBUG, validate
(Jul 04, 2010, 02:53:29 AM), com.hyperion.config.wizard.impl.RegistryWizardState, DEBUG, connect test
(Jul 04, 2010, 02:53:29 AM), com.hyperion.config.wizard.impl.RegistryWizardState, DEBUG, driver set
(Jul 04, 2010, 02:53:29 AM), com.hyperion.config.wizard.impl.RegistryWizardState, DEBUG, server= hyperion
(Jul 04, 2010, 02:53:29 AM), com.hyperion.config.wizard.impl.RegistryWizardState, DEBUG, whiteSpace remove
(Jul 04, 2010, 02:53:29 AM), com.hyperion.config.wizard.impl.RegistryWizardState, DEBUG, begin test cycle
(Jul 04, 2010, 02:53:29 AM), com.hyperion.config.wizard.impl.RegistryWizardState, DEBUG, define driver
(Jul 04, 2010, 02:53:29 AM), com.hyperion.config.wizard.impl.RegistryWizardState, DEBUG, make connection
(Jul 04, 2010, 02:53:29 AM), com.hyperion.config.wizard.impl.RegistryWizardState, DEBUG, set URL
(Jul 04, 2010, 02:53:29 AM), com.hyperion.config.wizard.impl.RegistryWizardState$1, DEBUG, connection is NOT null
(Jul 04, 2010, 02:53:29 AM), com.hyperion.config.wizard.impl.DBConnectionForm, DEBUG, DB type string = Oracle
(Jul 04, 2010, 02:53:29 AM), com.hyperion.cis.config.AbstractProductDBConfigurator, DEBUG, JDBC driver class is hyperion.jdbc.oracle.OracleDriver
(Jul 04, 2010, 02:53:29 AM), com.hyperion.cis.config.AbstractProductDBConfigurator, DEBUG, Connection URL: jdbc:hyperion:oracle://hyperion:1521;SID=orcl
(Jul 04, 2010, 02:53:29 AM), com.hyperion.config.wizard.impl.RegistryWizardState$1, DEBUG, validate CREATE_NEW, no registry DB exists, create it
(Jul 04, 2010, 02:53:29 AM), com.hyperion.hit.registry.RegistryConnection, ERROR, SQL Exception [Hyperion][Oracle JDBC Driver][Oracle]ORA-01031: insufficient privileges CAUSE null
(Jul 04, 2010, 02:53:29 AM), com.hyperion.config.wizard.impl.RegistryWizardState$1, ERROR, com.hyperion.hit.registry.exceptions.RegistryException: Unable to create registry.
(Jul 04, 2010, 02:53:29 AM), com.hyperion.cis.config.wizard.adapter.WizardFormAdapterPanel, ERROR, Unable to check Shared Services database existence: an error occured.
------------configtool_err.log------------
(Jul 04, 2010, 02:53:29 AM), com.hyperion.hit.registry.RegistryConnection, ERROR, SQL Exception [Hyperion][Oracle JDBC Driver][Oracle]ORA-01031: insufficient privileges
CAUSE null
(Jul 04, 2010, 02:53:29 AM), com.hyperion.config.wizard.impl.RegistryWizardState$1, ERROR, com.hyperion.hit.registry.exceptions.RegistryException: Unable to create registry.
(Jul 04, 2010, 02:53:29 AM), com.hyperion.cis.config.wizard.adapter.WizardFormAdapterPanel, ERROR, Unable to check Shared Services database existence: an error occured.
Hope to here from Some one.
Any help would be appreciated. Thank you.

Thanx John for your kind reply. i reffred your other posts and those are very helpfull for me.
I don't have any previous ver. of Hyperion. and i created a new database 'Orcl' for configuring the shared services and given the user name as 'hss'. i also tried to delete my old database and and reg.properties file from Hyperion Dir u suggested in some other post. but still its not working.
Today I have started again with fres installation of Windows Server 2003 oracle 11g EPM 11.1.3.
Also I m Installing this on VMware. I hope this is not the issue as i already installed Microsoft Loopback Adapter.
I will let you know the updates.
but still looking forward for your Kind help.
Edited by: Gaurav_Choudhari on Jul 5, 2010 12:37 AM

Shared or Dedicated server mode

My database is configured like:
9i Release2, Enterprise edition, OLTP, DEDICATED server mode!
I have more than 40 users who connect to db through WAN.
Is this good selection, I meen on server mode, or is better way to use SHARED s.mode. And way?!
Also where could I see which server mode of db is installed?
Thanks!

If we are talking about 40 physical end users, I wouldn't consider shared server mode. Shared server is ideal when you have so many users that the server would simply fall over if it tried to spawn that many dedicated connections.
Justin
Distributed Database Consulting, Inc.
http://www.ddbcinc.com/askDDBC

One shared mailbox with multiple distribution groups connected and the sent items folder - how to configure?

Hi!
I have been struggling for a while now with the following issue.
For starters:
We are using exchange 2010 in combination with outlook 2013 on client computers.
Cause of the limitations concerning the number of mailboxes in outlook im looking for a solution to receive and reply
to multiple aliasses. So i did the following:
1. Configured one shared mailbox.
2. Configured multiple distribution groups
3. made the shared mailbox a member of the distribution groups
4. Configured full access and send as permissions for myself on the shared mailbox ( testing )
5. Gave send as permissions to the shared mailbox in Active directory.
6. Logged in to OWA to setup rules for the shared mailbox.
I now receive emails from all connected distribution groups in the shared mailbox and also in the right folder.
I do however have to select the proper from address when i reply to an email.
the email sent by the main SMTP of the shared mailbox is placed into the sent folder of the shared mailbox.
I setup the senddelagate blabla in register.....
When i sent an email as one of the connected distribution groups it fails to put the sent item in the sent items folder of the shared mailbox. The email is sent using the proper address but placed in the sent folder of my main account.
I want this emails to end up in the sent items folder of the shared mailbox. Or even better, in a sent items folder for each of the addresses.
Any suggestions ?
Thanks in advance!

Hi,
As what
Rajkumar says, sending as a shared mailbox(full access permission) will put the email in the sent item of shared mailbox. But it cannot be located in the “sent item” of a distribution group. Because
it is a distribution group instead of a enabled user mailbox.
According to your further description, I understand that the reason why you configure that is some users reached the
limitation about the number of Exchange accounts you can include in the same Outlook profile. Is it rights? If I misunderstand, please point it out.
By default, user can only add 10 Exchange accounts to the same profile. You can customize the limit to the number Exchange accounts in the same profile using the following registry data:
Key: HKEY_CURRENT_USER\software\policies\Microsoft\exchange
DWORD: MaxNumExchange
Value: integer value starting at 1 (default = 10 if DWORD is missing)
http://blogs.technet.com/b/outlooking/archive/2012/12/24/clarification-on-outlook-2010-and-additional-exchange-account-supportability.aspx
Hope it helps.
Thanks,
Winnie Liang
TechNet Community Support

Help with "DAC Configure for Quadrature Mode.vi" in "ni5640R Frequency Translation" Example

Hi there:
I am also using the the NI PCI-5640R and I've been "studying" the
program: "Frequency Translation", my intention is to modify it and
produce a closed-loop between I and O.
I am also interested in transferring what i am reading through the
input port, directly to the output port but filtered AND with a
phase-shift (final Objective: Q-Control).
I need to visualize the signal in the HOST, so I need both FIFOS (DMA
FIFO and Local FIFO), and the "Quadrature Mode DAC Configure"
I would like to know:
1. How can I directly transfer the data acquired through the ADC port
into the DAC? (it is unclear due to the Event structure in the
"Frequency Translation" example)
2.
How can I configure the "Quadrature Mode DAC Configure.vi" for it to
bandpass-filter the signal comming from the ADC at a given frequency
and BW, specified by the user in the HOST? I have read that it is possible to filter a signal comming to the DAC using DUCs (Digital Upconverters) Does anyone has more info about this topic?
3. Is it possible to
configure the "Quadrature Mode DAC Configure.vi" to produce a
phase-shifted signal (phase shift also specified by user in the host)
I've
been working for almost 2 months trying to program the 5640R, doing
examples, and modifying them. After playing with different examples
I've come up to the conclusion that the "Frequency Translation" example
is the one that best-suites my application. My problem now is that I
AM LOST because i need more information regarding the configuration
parameters of ALL the different VI's inside the NI-5640R VI Tree to
exploit them correctly, specially the "Quadrature Mode DAC
Configure.vi".
Can anyone please help me?
Cheers...Antonio

Hello again:
Jerry:
1. I referred to the Event structure, but in the HOST, but now, with your commentary and Philippe's explanation i've undestood better the concept.
2. Regarding the filtering, I read the datasheet of the AD6654 (DAC from "Analog Devices" which is part of the n5640r) and in pages 36 and 37, it explains with an example, the possibility of designing a Bandpass CIC Filter by changing the interpolation (or decimation) factor of the DUC (or DDC). The filter can't be fully customized (the rejection and passband are limited to an "Alias rejection Table" in page 36), but it could fit the application to filter certain frequencies.
I also tryed what you guys suggested, meaning: I designed a simple digital bandpass butterworth IIR filter in the FPGA target inside a 3rd SCTL with a faster clock (i.e. "Top level timing source") and using a 2nd Local FIFO. The filter was done with FPGA discrete delays (z^-n) departing from a "differences equation" [y(n) = x(n-1)+x(n)+0.9996858*y(n-1)]. But I have problems with the 0.99... constant which is always rounded to 1 (check the pic). I changed the variable's type and digits of precision, but it still rounds up to 1 Any suggestions?
3. I was thinking as well of shifting the phase (as Jerry said) by configurating the NCO in the DAC. Again, more information is given in AD6654's datasheet (page 35). I will quote the info:
"The phase offset register can be written with a value that is added as an offset to the phase accumulator of the NCO. This 16 bit register is interpreted as 16-bit unregistered integer. A 0x0000 in this register corresponds to a 0 radian offset and a 0xFFF corresponds to an offset of 2pi*(1 - 1/2^16) radians. This register allows multiple NCOs (multiple channels) to be sinchronized to produce complex sinusoids with a known steady phase difference:"
Any ideas of how to program this register inside the "ni5640r ADC Configure NCO" to have a fixed phase offset of 90º?
Thanx in advance for your replies
'till the next post...Antonio
Attachments:
Digital IIR.JPG ‏122 KB

Configuring IDSM-2 Promiscuous Mode with MLS IP IDS

I am having a problem configuring promiscuous mode with an IDSM-2 running 5.0(3)S181.0 in a 6509 with Sup 720 running IOS 12.2(18)SXD4. I am running router interfaces without VLANs so I have created an extended access list with a 'permit ip any any' and configured this on my interfaces with 'mls ip ids access-list-name'. I configured 'intrusion-detection module x data-port 1 capture' and 'intrusion-detection module x data-port 2 capture', and because of the caution note on page 14-12 of 78-16127-01 I also configured 'intrusion-detection module x data-port 1 capture allowed-vlan 1-4094' and 'intrusion-detection module x data-port 2 capture allowed-vlan 1-4094'. After that I can see the output counters rising in 'show 'intrusion-detection module x data-port 1 traffic' and 'show 'intrusion-detection module x data-port 2 traffic'. I can configure the IDSM-2 using the VMS management center, and I added my sensor to security monitor and set the level down to informational, but I don't even see any events or even the start-up informational message. Anyone have any idea what I missed?

Here is a document on Configuring the Catalyst Series 6500 Switch for IDSM-2 in Promiscuous Mode.
http://www.cisco.com/en/US/products/sw/secursw/ps2113/products_configuration_guide_chapter09186a0080459221.html#wp1030752

Wrt320n with Apple Time Capsule in Wireless sharing mode

Hi!
I try to connect my LinkSys wrt320n with Apple Time Capsule with mode "sahring existing wireless network" and so Time capsule doesn't work. It gets IP, but writes "isn't internet connection, WiFi network don't find" and also in the admipage of my wrt320 I can't see Time Capsule as client.
Is it possible to make this mode with these two?
Thanks for your advice and solutions.

AlexFedy wrote:
I want to use TC as wireless station to share my wrt320n signal and also as backup. But, the first needs doesn't work properly
For setting up the Time Capsule to work as a wireless station, the WAN port should be connected to a modem. In your case, the WAN port should be connected to the to the ethernet port of the router since the modem is already connected to the Linksys. By the way, you don't need to setup a wireless station anymore since you already have a router, unless it serves as another purpose. In addition to that, if you want to setup the TC to do backup then you cannot use it as a wireless station anymore. It can only serve one purpose at a time, depending on the type of settings being set.

Configuring dedicated/shared mode with DBCA wizard

Similar Messages

Maybe you are looking for