Configuring the 3750G WLC to use the Internal DHCP Server
I want to use the Internal DHCP Server on a 3750G WLC to hand out IP's to gueat users. I'm having issues getting the DHCP server to hand out addresses for the guest network - any suggestions would be a great help.
Configuration Details are attached.
Configuring DHCP
http://www.cisco.com/en/US/docs/wireless/controller/5.2/configuration/guide/c52wlan.html#wp1293808
Similar Messages
-
WLC CT2504: Interface IP can not be used as internal DHCP server IP
Hello all,
I've got a new CT2504 controller with software version 7.0.220.0
Regarding to
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a0080af5d13.shtml
I've tried to configure the internal DHCP on a dynamic-interface, but this is not possible:
(Cisco Controller) >config interface dhcp dynamic-interface vlan401 primary 172.16.x.3
vlan401 Interface IP can not be used as internal DHCP server IP
It works, if I use another IP (aka DHCP server) in the same subnet or in another subnet. It works also for the management interface.
(Cisco Controller) >show interface detailed management
Interface Name................................... management
MAC Address...................................... d0:c2:82:xx:xx:xx
IP Address....................................... 10.2.x.135
IP Netmask....................................... 255.255.255.240
IP Gateway....................................... 10.2.x.129
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. 400
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 10.2.x.135
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Disabled
Scopes are defined and Proxy is enabled.
(Cisco Controller) >show dhcp summary
Scope Name Enabled Address Range
ap Yes 10.2.x.137 -> 10.2.x.140
intern Yes 172.16.x.20 -> 172.16.x.30
(Cisco Controller) >show dhcp proxy
DHCP Proxy Behaviour: enabled
Has somebody an explanation for this issue?
Thanks in advance,
Regard,
RobertYou can use the internal dhcp, but you need to set the primary dhcp as the management ip. So in your dynamic interface, your primary dhcp is configure with the wlc management ip address. Dhcp proxy also needs to be enabled and is enabled by default.
Thanks,
Scott Fella
Sent from my iPhone -
WLC 5508 Internal DHCP server issues
Hi,
I am hoping to get your feedback around the dhcp issues I am facing with Two Centrally Switched Wireless LANs. I have tried to explain the setup and the problems below and would appreciate it if anyone can suggest a solution for the problems I am facing:
The setup is as follows:
- I have a WLC 5508 which has been configured with 4 SSIDs, out of which 2 are using Central Authentication and Switching.
- I have an LWAP connected to the WLC in HREAP mode.
- WLC is configured as the DHCP server for clients connecting to the SSID 'Guest'. For the rest, I am using external dhcp server.
- Only one scope for Guest Interface is setup on the WLC.
Problems:
1. As far as I know, for WLC to act as internal dhcp server, it is mandatory to have the proxy enabled, but the Clients connecting to SSID 'Internet' are
unable to get an ip address from the external dhcp server, if dhcp proxy is enabled on the WLC. If i disable the proxy, it all works fine.
2. DHCP does not release the ip addresses assigned to clients even after they are logged out.
3. If a machine which was earlier connected to 'Guest' SSID connects to the 'Internet' SSID, it requests the same ip it was assigned by the WLC which it was assigned under 'Guest', but gets tagged with the Vlan configured on the management interface.
************Output from the Controller********************
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.116.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS + LDPE
(Cisco Controller) >show interface summary
Interface Name Port Vlan Id IP Address Type Ap Mgr Gu
est
guest 1 301 10.255.255.30 Dynamic No No
management 1 100 172.17.1.30 Static Yes No
service-port N/A N/A 192.168.0.1 Static No No
virtual N/A N/A 10.0.0.1 Static No No
(Cisco Controller) >show wlan summary
Number of WLANs.................................. 4
WLAN ID WLAN Profile Name / SSID Status Interface Name
1 LAN Enabled management
2 Internet Enabled management
3 Managment Assets Enabled management
4 Guest Enabled guest
(Cisco Controller) >show dhcp detailed guest
Scope: guest
Enabled.......................................... Yes
Lease Time....................................... 86400 (1 day )
Pool Start....................................... 10.255.255.31
Pool End......................................... 10.255.255.254
Network.......................................... 10.255.255.0
Netmask.......................................... 255.255.255.0
Default Routers.................................. 10.255.255.1 0.0.0.0 0.0.0.0
DNS Domain.......................................
DNS.............................................. 8.8.8.8 8.8.4.4 0.0.0.0
Netbios Name Servers............................. 0.0.0.0 0.0.0.0 0.0.0.0
(Cisco Controller) >show interface detailed management
Interface Name................................... management
MAC Address...................................... e8:b7:48:9b:84:20
IP Address....................................... 172.17.1.30
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 172.17.1.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. 100
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 172.30.50.1
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Enabled
(Cisco Controller) >show interface detailed guest
Interface Name................................... guest
MAC Address...................................... e8:b7:48:9b:84:24
IP Address....................................... 10.255.255.30
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 10.255.255.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. 301
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. Unconfigured
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... No
Guest Interface.................................. No
L2 Multicast..................................... Enabled
(Cisco Controller) >show dhcp leases
MAC IP Lease Time Remaining
00:21:6a:9c:03:04 10.255.255.46 23 hours 52 minutes 42 seconds <<<<<<< lease remains even when the client is disconnected.
*********Example of Client connected to the right Vlan with an ip address from the incorrect interface. *************
(Cisco Controller) >show client detail 00:21:6a:9c:03:04
Client MAC Address............................... 00:21:6a:9c:03:04
Client Username ................................. N/A
AP MAC Address................................... a0:cf:5b:00:49:c0
AP Name.......................................... mel
Client State..................................... Associated
Client NAC OOB State............................. Access
Wireless LAN Id.................................. 2 <<<<<<<< 'Internet' SSID
BSSID............................................ a0:cf:5b:00:49:ce
Connected For ................................... 319 secs
Channel.......................................... 36
IP Address....................................... 10.255.255.46 <<<<<<< IP address assigned from the 'Guest' Interface or dhcp scope on the WLC
Association Id................................... 1
Authentication Algorithm......................... Open System
Reason Code...................................... 1
Status Code...................................... 0
Session Timeout.................................. 1800
Client CCX version............................... 4
Client E2E version............................... 1
QoS Level........................................ Silver
802.1P Priority Tag.............................. disabled
WMM Support...................................... Enabled
Power Save....................................... OFF
Mobility State................................... Local
Mobility Move Count.............................. 0
Security Policy Completed........................ Yes
Policy Manager State............................. RUN
Policy Manager Rule Created...................... Yes
ACL Name......................................... none
ACL Applied Status............................... Unavailable
Policy Type...................................... N/A
Encryption Cipher................................ None
Management Frame Protection...................... No
EAP Type......................................... Unknown
H-REAP Data Switching............................ Central <<<<<<<<<
H-REAP Authentication............................ Central <<<<<<<<<<
Interface........................................ management
VLAN............................................. 100 <<<<<<<<<<< right Vlan
Quarantine VLAN.................................. 0
Access VLAN...................................... 100Hi All,
I have a similar issue where Wireless clients are not receiving automatic addressing from an internal DHCP server. I have multiple interfaces configured on the WLC which are connected to separate VLANS. The manually specified DHCP primary server entry is the same on all interfaces. Some clients are able to authenticate and receive automatic IP configuration but some clients are failing the address assignment process. I have checked connectivity between the WLC and DHCP server, this is confirmed as working. When I carry out a "debug dhcp packet enable", I get the following outputs which seems as if the DHCP discover request from the client is skipped. Your thoughts and inputs on this are appreciated.
DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option len (including the magic cookie) 76
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: message type = DHCP DISCOVER
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 116 (len 1) - skipping
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 61 (len 7) - skipping
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: requested ip = 169.254.223.5
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 12 (len 13) - skipping
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: vendor class id = MSFT 5.0 (len 8)
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 55 (len 11) - skipping
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 43 (len 2) - skipping
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP options end, len 76, actual 68
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP Forwarding DHCP packet (332 octets) packet DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option len (including the magic cookie) 76
Thanks,
Raj Sandhu -
Does option 43 matter ? WLC5508 ver 7.2 using internal DHCP server
I am using a WLC 5508 and its internal DHCP server. I cant find anywhere I can setup option 43. However, the access points are connected in just fine. Do I need to worry about setting up a seperate DHCP server to get option 43 setup properly ?
Thank you.Sorry I didnt make my question clear.
I am using a WLC 5508 and its internal DHCP server. I cant find anywhere I can setup option 43.
When I connect a CAPWAPP Access Point to the network, it receives IP address from the WLC 5508 DHCP service just fine. It shows up in the access points list and users can connect to it no problem.
Do I need to worry about setting up a seperate DHCP server to get option 43 setup properly ? -
i want to buy an iphone 4s ans also i'm going to the usa on my summervacation! (yeah!) but, will the guarantee/warranty be available international, so if i bu it in the usa, can i use the guarantee/warranty in holland? thanks!! maybe extra carepacks?
soo, this is actually what i whould like to know maybe i should buy extra carepackages, in the usa? or maybe in holland?
thanks in advance!!Limnos wrote:
The iPhone warranty is not international. If something goes wrong with it you will have to have somebody in the USA take it to a store in the USA for service (or pay for it yourself at home).
http://www.apple.com/legal/warranty/iphone/
I have heard stories that Apple will not even look at an iPhone purchased
in another country at any price since they will not be able to replace with an
identical iPhone which is their practice ( carrier locked etc) -
I travel between countries often for my work. What is the best iphone to use for international calling at a reasonable cost?
All six Uk carriers carry the iPhone officially and micro sims are very common therefore
PAYG is very common in UK every carrier offers a number of packages but all commitment free
http://support.apple.com/kb/ht1937
List of Turkish Carriers within this doc -
My wife and I want to swap her iphone 4s for my iphone 4 while I take a short trip out of the country. We use the same itunes account but have different email accounts. Can we just change our phone numbers with our carrier and change email addresses on our phones so we get correct messages, with out disturbing our other apps?
The email is simple. Just delete her email acoount on her iPhone and configure your account into the phone and then do the same for her on your phone.
The harder issue is that to switch the cellular phone service you will need to switch the SIM cards and the two phones do not use the same size SIM card. -
Does anyone know how the internal DHCP server in these access points connects to virtual interfaces and bridges in the unit?
Is there some sort of default connection that connects the DHCP server to the native bridge group or VLAN?
In a test case, with an SSID in the native VLAN and bridge group, the 1702i serves an IP address to a wireless client no problem. But with a second SSID in a non native VLAN and bridge group, no IP gets served. My only guess is that since the bvi1 defaults to the native bridge group and VLAN, sub-interfaces also in this group are assumed to be in the same subnet as bvi1, or in this case:
interface bvi1
ip address 192.168.1.205 255.255.255.0
no ip route-cache
exit
It would be the ..1. subnet.
Since the dhcp pool is set as:
ip dhcp pool GeneralWiFi
network 192.168.1.0 255.255.255.0
lease 1
default-router 192.168.1.1
dns-server 8.8.8.8
exit
There may be an assumption that anything bvi1 can talk to is in the ..1. subnet, so the above pool gets activated on a request coming through bvi1.
Is the DHCP server just hanging out waiting for a request from an "area" that is assumed to be on the same subnet as the given pool?
Do I need to somehow show the device what subnet the 2nd SSID/ subinterfaces are in so the internal DHCP server can decide it needs to go to work, or is there some sort of bridging between the DHCP server and the interfaces that needs to be done? I am trying to use the same DHCP pool for the second subnet at this point, since I assume I will need another router to service an additional subnet and DHCP pool.Keep in mind that DHCP is a broadcast packet to start. So the AP can only listen in the subnet that it has an IP address for.
Now, for any other subnet you can use the AP for DHCP but you have to have an IP helper address on your L3 pointing back to the AP.
That being said, I wouldn't use the DHCP server on the AP as it is limited. You'd be better off using a Microsoft server or some other device that is designed for DHCP.
HTH,
Steve -
How to return the result ( fields ) form using the BDC in background mode ?
hi,
I am now having to develop a sub routines for executing the transaction COR1 using BDC ( transaction SHDB ) , in the FORM i pass the 4 params for the fields of the screens of the transaction ( COR1 is used for creating the process order ) , and at last i have to take the number of the process order that has been created by the transaction , how can i do that , if we can no , in which table it is contained ( AUFNR ) ? .
In fact , i use the CALL TRANSACTION 'COR1' USING BDCDATA......
so , if you please to help me resolve this problem ( it is really urgent )...
Thank you so much .Thank you so much for your reply , I think that it would be very useful to me .
Hi Vijay Sai , i have used the itab TYPE BDCMSGCOLL for calling the transaction but just for taking the error messages , so as you say , it contains all the values of the fields including AUFNR ( which i need to get the its value after creating with COR1 ) .......if it is right , we just need to access the new value by using the query at the internal table just like :
LOOP AT itab INTO wa.
if wa-fname = 'AUFNR' .
res = ws-fval .
ENDIF.
Is that right ? -
Hello, i have a problem with the adobe photoshop elements 10 in the organizer impossible to use the magic mouse, Where can I configure this one?
Thank you.What do you mean by "impossible to use"? I use a magic mouse with PSE all the time. What are you wanting to do that isn't working?
-
Hi All,
Am trying to test the Collaboration portal url using the below option in SICF but it is only pulling a blank screen.
The path in SICF is : /sap/bc/ui5_ui5/tmui/coll_portal
The webpage does not reflect any error except a blank screen.
Is there any basis side or TM side configuration that needs to be done to have data displayed on that webpage?
Appreciate quick reply.
Thanks.
SatHi Jan,
Now am getting this error :
Gateway service /SCMTMS/USER not active
From the security guide I found a handful of services to be activated :
The following services are required if you intend to use the SAP TM Collaboration Portal:
●
/sap/public/bc/ur/
●
/sap/public/bc/icf/logoff
●
/sap/public/bc/UI2/
●
/sap/bc/ui2/startup
●
/sap/opu/odata/SCMTMS/TENDERING/
●
/sap/opu/odata/SCMTMS/USER/
●
/sap/opu/odata/SCMTMS/GENERAL/
●
/sap/opu/odata/SCMTMS/EVENT_NOT/
●
/sap/opu/odata/SCMTMS/INVOICE_SUBMISSION
●
/sap/opu/odata/SCMTMS/FRT_PROCUREMENT
●
/sap/opu/odata/SCMTMS/INVOICING
●
/sap/bc/ui5_ui5/tmui/coll_portal/
But in my system, in SICF only this path is present /sap/opu/odata.
/SCMTMS onwards is missing, so am not able to activate these bunch of services which ideally should be present in the system. Hence am thinking to open a ticket with SAP for the same.
What you suggest?
Regards,
Sat -
Does the latest Ipod Classic use the same charging pins as the earlier versions?
Does the latest Ipod Classic use the same charging pin positons as the earlier versions as I want to use it in my Audi where my 5th gen Nano will play but not charge as the pin configuration for charging changed from that of the earlier models.
If your 5th gen nano doesn't change, then a new iPod Classic will not either.
The "change" was that older iPods used firewire to charge the iPod. But that's 12volts (the same voltage as a car's battery). Then along came charging by USB, which is 5volts. So car manufacturers who were on the ball, introduced electronics to drop the 12v car battery voltage to 5v and put that 5v on the appropriate USB pins. (I would hope, that by now, every car manufacturer has sorted this out, but of course that doesn't help anyone with an older model car.)
The incredibly obvious - to anyone with technical knowledge - was that one day, Apple would stop the 12v charging method on newer models of iPod. But somehow, a lot of manufacturers of devices that charge iPods failed to see this. (It really was incredibly obvious, believe me!)
It wasn't just car manufacturers who were caught out by this, so were Docking Station devices. I know of one make, where the manufacturer recalled the ones still in shops so that they could re-work them to charge using the 5v USB pins.
In my car, made around 2006, I had an external device fitted so that I could plug my iPod into the car stereo through the Dock Connector. But hey, guess what? That device will charge my iPod Classic, but not my iPod Touch.
A long-ish answer, but hopefully it not only answers the question, but tells you why too. -
How do I remove an old username from the app store when using the update function
How do I remove an old username from the app store when using the update function.
I purchased my Mac used. The former owners username prepopulates when I try to perform the updated function on the app store. It does not allow me to use a different user name. I have created my own username and password. I have even been able to purchase items from the app store, it's just when I use the update function it does populate with my username. Any help is appreciated.The first thing to do with a second-hand computer is to erase the internal drive and install a clean copy of OS X. You — not the previous owner — must do that. How you do it depends on the model, and on whether you already own another Mac. If you're not sure of the model, enter the serial number on this page. Then find the model on this page to see what OS version was originally installed.
1. You don't own another Mac.
If the machine shipped with OS X 10.4 or 10.5, you need a boxed and shrink-wrapped retail Snow Leopard (OS X 10.6) installation disc from the Apple Store or a reputable reseller — not from eBay or anything of the kind. If the machine has less than 1 GB of memory, you'll need to add more in order to install 10.6. Preferably, install as much memory as it can take, according to the technical specifications.
If the machine shipped with OS X 10.6, you need the installation media that came with it: gray installation discs, or a USB flash drive for some MacBook Air models. For early MBA models, you may need a USB optical drive or Remote Disc. You should have received the media from the previous owner, but if you didn't, order replacements from Apple. A retail disc, or the gray discs from another model, will not work.
To boot from an optical disc or a flash drive, insert it, then reboot and hold down the C key at the startup chime. Release the key when you see the gray Apple logo on the screen.
If the machine shipped with OS X 10.7 or later, you don't need media. It should boot into Internet Recovery mode when you hold down the key combination option-command-R at the startup chime. Release the keys when you see a spinning globe.
2. You do own another Mac.
If you already own another Mac that was upgraded in the App Store to the version of OS X that you want to install, and if the new Mac is compatible with it, then you can install it. Use Recovery Disk Assistant to create a bootable USB device and boot the new Mac from it by holding down the C key at the startup chime. Alternatively, if you have a Time Machine backup of OS X 10.7.3 or later on an external hard drive (not a Time Capsule or other network device), you can boot from that by holding down the option key and selecting it from the row of icons that appears. Note that if your other Mac was never upgraded in the App Store, you can't use this method.
Once booted in Recovery, launch Disk Utility and select the icon of the internal drive — not any of the volume icons nested beneath it. In the Partition tab, select the default options: a GUID partition table with one data volume in Mac OS Extended (Journaled) format. This operation will permanently remove all existing data on the drive.
After partitioning, quit Disk Utility and run the OS X Installer. You will need the Apple ID and password that you used to upgrade. When the installation is done, the system will automatically reboot into the Setup Assistant, which will prompt you to transfer the data from another Mac, its backups, or from a Windows computer. If you have any data to transfer, this is usually the best time to do it.
Then run Software Update and install all available system updates from Apple. To upgrade to a major version of OS X newer than 10.6, get it from the Mac App Store. Note that you can't keep an upgraded version that was installed by the previous owner. He or she can't legally transfer it to you, and without the Apple ID you won't be able to update it in Software Update or reinstall, if that becomes necessary. The same goes for any App Store products that the previous owner installed — you have to repurchase them.
If the previous owner "accepted" the bundled iLife applications (iPhoto, iMovie, and Garage Band) in the App Store so that he or she could update them, then they're linked to that Apple ID and you won't be able to download them without buying them. Reportedly, Apple customer service has sometimes issued redemption codes for these apps to second owners who asked.
If the previous owner didn't deauthorize the computer in the iTunes Store under his Apple ID, you wont be able to authorize it immediately under your ID. In that case, you'll either have to wait up to 90 days or contact iTunes Support. -
The application does not use the screen and run in the background
Hi
I have downloaded a package of j2me Midlet
from [link] here [link]
and try to reuse the code
but I get the following error when running the code:-
The application does not use the screen and run in the background
I think the error into one of these two classes
package main;
import javax.microedition.midlet.*;
import javax.microedition.midlet.*;
import javax.microedition.lcdui.*;
import javax.microedition.media.Manager;
import javax.microedition.media.MediaException;
import javax.microedition.media.Player;
import java.io.IOException;
import java.io.InputStream;
public class MainMidlet extends MIDlet implements CommandListener {
private SSGameCanvas gameCanvas ;
private Command exitCommand ;
private Player player = null;
public void startApp() {
try {
// create new game thread
gameCanvas = new SSGameCanvas();
gameCanvas.start(); // start game thread
exitCommand = new Command("Exit",Command.EXIT,1);
gameCanvas.addCommand(exitCommand);
gameCanvas.setCommandListener(this);
Display.getDisplay(this).setCurrent(gameCanvas);
catch (java.io.IOException e)
e.printStackTrace();
try {
// start sounds
InputStream in = getClass().getResourceAsStream("/resource/startfly.wav");
player = Manager.createPlayer(in,"audio/x-wav");
player.setLoopCount(1);
player.start();
catch (MediaException ex)
ex.printStackTrace();
catch (IOException ex)
ex.printStackTrace();
public void pauseApp() {
public void destroyApp(boolean unconditional) {
if (player != null) {
player.close();
System.gc();
public void commandAction(Command command, Displayable displayable) {
if (command == exitCommand)
destroyApp(true);
notifyDestroyed();
package main;
import java.io.IOException;
import javax.microedition.lcdui.*;
import javax.microedition.lcdui.game.*;
public class SSGameCanvas extends GameCanvas implements Runnable {
protected GameManager gameManager;
protected boolean running;
private int tick=0;
private static int WIDTH;
private static int HEIGHT;
private int mDelay = 20;
Form mainForm;
Display display;
//private int MaxTime;
public SSGameCanvas() throws IOException{
super(true);
gameManager = new GameManager(5,5,getHeight()-10,getWidth()-10,this);
public void start() {
this.running = true;
Thread t = new Thread(this);
t.start();
public void stop() {
running = false;
public void render(Graphics g) {
WIDTH = getWidth();
HEIGHT = getHeight();
// Clear the Canvas.
g.setColor(0, 0, 50);
g.fillRect(0,0,WIDTH-1,HEIGHT-1);
// draw border
g.setColor(200,0,0);
g.drawRect(0,0,WIDTH-1,HEIGHT-1);
// draw game canvas
gameManager.paint(g);
public void run() {
while (running) {
// draw graphics
render(getGraphics());
// advance to next graphics
advance(tick++);
// display
flushGraphics();
try { Thread.sleep(mDelay); }
catch (InterruptedException ie) {}
public void advance(int ticks) {
// advance to next game canvas
gameManager.advance(ticks);
this.paint(getGraphics());
}Edited by: VANPERSIE on Jul 10, 2012 12:26 PMHi Andi,
Thanks for your reply.
Yes, I have waited for a while and the result doesn't change.
The Porblem here is the application is seen started in visual administrator.Only restart brings up the page back.
Can you please suggest anything.
Thanks and regards
Nagaraj -
i have two apple id accounts ,when i used to update application it used to prompt a default id (the old one) and if the application was downloaded using the other id i would cancel and it would prompt the other id but not any more .
it just prompt the old id which im not signed in with im signed in using the new id and when i cancel nothing happens and when i try to update applications separately i have the same problem .
im signed in using the new id
the old one is my wife's so i can't delete it
the problem happens when i update all or each application by its own
using ios 5.0.1 on a iphone 3gs
the applications are downloaded using both the new and old id's
any help will be greatly appreciatedِThese are user-to-user forums, you are not talking to Apple here and they don't monitor these forums - I've asked the hosts to remove yout account ids from your post.
In terms of combining accounts it's not currently possible to do so, nor to copy/transfer content from account to another.
Maybe you are looking for
-
Excel 2013 and Random Excessive Processor Utilization
Every now and then (about once per day), my Excel 2013 will randomly seize one of my 8 threads and max it out. My PC is quad-core and hyper-threaded, so it shows up in task manager as 8 cores. When Excel seizes, its UI still seems to function prope
-
Can you bring your phone back from an accidental restore?
I just got the iphone 4. I plugged it up to my itunes and it asked to restore from previous iphone or retore like a new phone. I picked from previous phone. Well it ended up clearing EVERYTHING off. All the stuff I had transfered. So my question is c
-
FFiles I store to Dropbox do jot now appear on my iPad Dropbox app. They used to. If I reload Dropbox then it synchs all but I lose the favourites and when I save my more files they do not synch to this device.
-
I have about 1500 photos in my iPhoto '09 v8.1.2 (424) library. I had "Copy items to iPhoto library" unticked, as the photos were all stored on a Western Digital "MyBook" network drive. However, the drive exploded in a way that gave me no chance of
-
within the update BIOS file i dloaded there is a "HOW TO FLASH BIOS.doc" but i do not know which section to follow - AMI or AWARD or (i guess) NON_FAT32 i need to know because i am trying to get my 2*512 OCZ 3700EB to work