Connection to switch not working
I'm having problems with connecting my UltraSPARC-IIi machine runing Solaris 9/64 to a SURECOM switch.
I think that the software configuration is ok, I managed to connect the Solaris machine directly to another machine running Linux without problems. However it would not work when it's connected to the switch.
I used 2 different cables that I've tested and works fine. Is there some special requirement from the Solaris ethernet card regarding the cable that is used?
During bootup i get this message:
SUNW, hme0 : No response from Ethernet network : Link down -- cable problem?
Well, you could try and add the hme patch for SunOS 5.9: 113226-05.
You could also try and force the interface to 100 MB/FDX (if your switch supports it).
If you have several interfaces, start with
ndd -set /dev/hme instance <instance>
For hme0:
ndd -set /dev/hme instance 0
ndd -set /dev/hme adv_100fdx_cap 1
ndd -set /dev/hme adv_100hdx_cap 0
ndd -set /dev/hme adv_10fdx_cap 0
ndd -set /dev/hme adv_10hdx_cap 0
ndd -set /dev/hme adv_autoneg_cap 0
7/M.
Similar Messages
-
Just upgraded to Lion an am discovering that I cannot send email photos from within iPhoto. Error message says bad Internet connection or server not working, when that's not the case. Never happened in Snow Leopard! Help!!!
what email service - Yahoo mail have been acting up lately
you can try setting Mail as your email client - it resolves this pfoblem for some people
LN -
i have problem with my iphone 5 lock switch..as lock switch not working properly..and my iphone is not in warrenty.. so plz tell me what i do...
The iPhone 5 is less than a year old, so all of them should still be in warranty unless they have been jailbroken or physically damaged. If you have a hardware problem as you describe the only option is to get the phone replaced by Apple or repaired by a non-authorized shop. The Apple replacement will be free at any Apple store in the country where the phone was purchased. If Apple determines that the phone was physically damaged or jailbroken it will cost $229.
-
Wifi connection with 4s not working after installing new software ios6
wifi connection with 4s not working after installing ios 6.
Go to Settings > WiFi > Select your network and hit the right arrow to "Forget Network"
Then go to Settings > General > Reset Network Settings and try connecting again when the phone restarts. -
HT1430 My iphone5 on/off switch not working, even we not able to reset the phone
Hi,
My iphone5 on/off switch not working, even we not able to reset the phoneOK, so are you asking what do to, or are you just sharing your situation?
If you're asking what to do, then you should bring your phone to Apple while it's still under warranty. -
IPhone 4s bluetooth connects but does not work handsfree
My iPhone 4s bluetooth connects but does not work handsfree. Has worked fine with My iPhone 3s. The Light on my VW turns green indicating a connect, but the phone does not work through the VWs audio.
Fixed by power cycling the iPhone
-
5800 Connection Manager is not working correctly
I have my preferred connections setup with my home WLAN as priority, then my cell phone provider (ATT) as the last priority. The connection manager switches from my WLAN to ATT everytime I go out of range of my WLAN fully automatically. So that part is working as designed.
The problem is when I get back to my home WLAN the connection manager doesn't automatically drop the EDGE or 3G connection and connect to my WLAN.
To make things worse, even if I kill the EDGE or 3G connection manually, it may or may not pick up my WLAN and start using it.
Then, if I can get the WLAN to connect, the connection manager will insist on connecting to the EDGE/3G connection and disconnecting the WLAN.
This is crazy behavior. I've been pretty happy with the phone's stability over my old N78, but I hope to Zeus that a Firmware upgrade will be release that fixes this bug. It drives me nuts.
So far the only way I can get the connection manager to resume it's expected behavior is to power off the phone and pull the battery. Then it will behave for a few days before becoming schizophrenic.
If you have any tips on how to correct this behavior, I'd appreciate hearing it.
cheers,
mikehd
5800XM NE
F/W 40.2.005
Solved!
Go to Solution.mikehd wrote:
The problem is when I get back to my home WLAN the connection manager doesn't automatically drop the EDGE or 3G connection and connect to my WLAN.
Then, if I can get the WLAN to connect, the connection manager will insist on connecting to the EDGE/3G connection and disconnecting the WLAN.
This is crazy behavior. I've been pretty happy with the phone's stability over my old N78, but I hope to Zeus that a Firmware upgrade will be release that fixes this bug. It drives me nuts.
So far the only way I can get the connection manager to resume it's expected behavior is to power off the phone and pull the battery. Then it will behave for a few days before becoming schizophrenic.
First, you may get much better response if you post in the appropriate forum. in you case, "Connectivity."
Dropping an active connection & switching to another connection is probably not designed behavior. So in your case if the 3G connection is active, I can understand why it is not switching to WLAN. I can also see why it might be a "nice-to-have" feature, but in some cases dropping an active connection may cause problems with applications that are using it, so you may end up with more problems if the connection kept changing (maybe).
Firmware upgrade will not change as-designed behavior, but what you're describing sounds like there's some application which is configured to use either "default" or the 3G connection. What I would do is look through all applications that are using the net and check the connection settings in each one and make sure it's set to use "Internet"
Another thing you can do is set the AT&T connection to "always ask" mode so that it doesn't get used without you clicking OK.
Lumia 920, Lumia 800
Nokia N8-00 (NAM, Product Code: 059C8T6), Symbian Belle, Type RM-596, 111.030.0609
Nokia 5800 XpressMusic (NAM, Product Code: 0577454) Software v51.2.007, Type RM-428 -
Application switcher not working as expected
I am using the French localisation of Leopard. Using Application switcher (ie Cmd-Tab) I was able on Tiger to quit a running app by pressing A (an oddity due to the AZERTY / QWERTY differences). This does not work any more and I cannot quit an application from Application switcher. Any advice?
Cool. Learn a new trick every day... It works on my English keyboard (with the Q).
Maybe the "oddity" has been fixed and it is no longer A on the French keyboard, but Q, as it should be. -
Keyboard layout switching not working
i use xfce4 and i created /etc/X11/xorg.conf
Section "InputClass"
Identifier "Keyboard Defaults"
MatchIsKeyboard "yes"
Option "XkbLayout" "us, ar"
Option "XkbOptions" "grp:alt_shift_toggle"
EndSection
but it's not working.
xfce4 has a program called Keyboard in settings menu, i used it it gives the ability to add another language but it doesnt has a switching capability.I don't use keyboard layout switch through xorg.conf because it stops to work sometimes(if i use setxkbmap for example).
So i am using setxkbmap in .xinitrc.
setxkbmap -model pc105 \
-layout "de,ru" \
-variant "basic,phonetic" \
-option -option "grp:sclk_toggle, grp_led:scroll, terminate:ctrl_alt_bksp, caps:none"
and "kbdd" for remembering layout for each window.
Change it to your needs or check the arch wiki about xorg.conf.d . -
IPod connection to car not working?!
My iPod Nano (not sure if it's 4th Gen or not... not sure how to tell sorry) will not work with my car stereo anymore Up to a few days ago we hooked it up to our Honda (has a USB port in the arm rest) and it played through the car stereo. Today we went to use it and it recognizes the iPod, shows the song name on the stereo display but no sound comes out (the volume is up). We tried my nephews iPod and it works with sound, we tried connecting the earbuds to my iPod and there is music... so I'm stuck now because the cord works with another iPod and the headphones work on mine... any suggestions/ideas/help? Am I just not thinking of something? We're travelling so this is important lol
TIA,
SarahHi there, have you guys gotten your problem solved yet?
If not try to reset your ipod. you can reset it by holding the centre and menu button at the same time until the screen displays an aple logo. try that and see if that fixes your problem.
oh by the way to tell if your ipod nano is 4th gen it will look like one of these from the following webpage:
http://www.apple.com/ipodnano/
Peace! -
Has anybody experienced the iPhone off switch not working all the time.
I have an iPhone 5, it's about 16 months old and it has experienced an annoying issue. The off button does not work all the time, sometimes I have to press it multiple times and other times it just works. The worst case is when it does not work at all, very frustrating. I didn't expect this type of issue for a phone that is not even a year and a half old.
I did some searching on the internet and there are 2 schools of thought, the first is that this is a hardware fault and Apple know about it but won't admit it because it would cost them too much to repair/replace phones with the issue. The second school of thought is that it is a software issue and a backup/reset/restore will fix it; I tried doing this but it did not resolve the issue.
Further digging seemed to suggest that it was really a hardware fault and the only option was to get a refurb from Apple for a ton of money, not cool.
Anyway, if anyone has any more information that could help me resolve this issue I would greatly appreciate it.
//*eggbox23@diesel vdub, thanks for your suggestion, I setup an appointment with the Genius Bar and found out in about 5 minutes that everything I have read up on so far is true.
Firstly the technician admitted that there is a sporadic fault on the iPhone 4s and iPhone 5 switches, something to do with the design of the switch that included a rubber element that rolls up (whatever that means) and causes the switch to fail. He then indicated that the iPhone 5s does not have the issue because the switch has been completely redesigned.
Since I was stupid enough to not take out the extended warranty the only options he gave me were to purchase a new phone or to get a refurb for $269, not cool. Why would anyone think that a phone would not work correctly for 2 whole years when the phone only cost about $600!
Since I have about 7-8 months left on my phone contract I am not prepared to pay for either option. I find it amazing that a phone can develop this type of issue in such a short time and then expect the customer to pay for their failures. Apple supposedly sells a very high quality product for a very high price, looks like they have taken a step back from this philosophy.
I am disappointed in the options that he gave me (I don't blame the technician) but I suppose I expected more from Apple in terms of quality and service.
//*eggbox23 -
Hi, i just bought a 4th-gen shuffle, and I've been using it with satisfaction since Saturday. Then yesterday i finished to listen to some music and I wanted to turn it off, so I slid the switcher to the right. The problem is that it won't turn off, no matter where I drag the slider, I'm still able to play music with it...
I'll try to restore it as soon as possible, cause I can't even try to reset it via turning it off...
Any clues? Thanks in adviceHI,
My Buddy list from iChat were separated before and stayed separated on "Upgrading"
The group names also stayed the same
Uploaded with Skitch!
I have Magic Mouse and single finger swipes do not work in either direction. (I don't have Laptop and track pad to test further.)
Actually changing it from the Browser Single Finger "Scroll" to "Swipe" with two fingers solved this.
Uploaded with Skitch!
You do lose access via Swipes to Full windowed apps. (you have to click the DOCK)
I find that then I do have access up a d down the list of open Chats.
9:24 PM Monday; March 26, 2012
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
iMac 2.5Ghz 5i 2011 (Lion 10.7.3)
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb (Snow Leopard 10.6.8)
Mac OS X (10.6.8),
"Limit the Logs to the Bits above Binary Images." No, Seriously -
Connection pooling does not work Oracle Objects! Oracle please respond!
The problem is that when we retrieve Oracle Objects using pooled connection (closing logical connection at the end of every call)it takes 6-8 times longer than in case we share the same physical connection for all database calls. Parts of our application which do not utilize Oracle Objects (just old good relational data) works just fine with pooled connections - no performance degradation
This is my reconstruction of f the what is happening behind the seen, so some parts can be not entirely correct.
OracleConnection class caches StructDescriptor objects in descriptorCache hash table. StructDescriptor objects map content of oracle STRUCTs which are retrieved through the connection onto oracle type names. For example if you retrieve an instance of HR.EMPLOYEE_T oracle object from database some metadata will be retrieved and stored as an entry in descriptorCache cache table associated with "HR.EMPLOYEE_T" key to assist CustomDatum interface. It is a time consuming process and caching of this metadata improves it dramatically.
Now when using pooled connection descriptorCache gets cleared when you close your logical connection (java.sql.Connection) so next time you get a connection from your pooled connection it will have to repopulate the cache which as I said is very time consuming. As a result even though we can reuse our physical connection by using pooled connection whole setup does not work - fetching metadata takes a long time and we cant use Oracle objects in EJB environment (or Servlet environment)
Alex Roytman
Peace Technology, Inc.
(301) 206-9696
nullcheck out managed datasources in the manuals
-
Had to reset router, wired connection fine wireless not working even w/out security
hi, after that freakin blackout that made my internet stop workin, i did a complete reset to my router, and reconfigured it all over again, now i can connect to the internet if im wired to it but if im wireless i cant (tried with other laptops, xbox and it wouldnt work) i even left the wireless without security but its the same, when i click on connect to my network, it hangs forever "connecting" and in the end it remains unconnected... BTW i have a button in wireless settings "Status SES Inactive" which in the first firmware version it wasnt there, and i dont know what its for and if i should use it (what is "SES"? its not in the help manual)
hi..
hmmm.....i hope i cn help u im not so sure if it will work but then try to do so....
access the set-up page...try 192.168.1.1 or if it will not prompt for a username and a password just in case that u r n a dsl connection use this 192.168.2.1...launch internet explorer and type 192.168.2.1 on the address bar u shud be promted with a username and password
leave the usrname blank and passwrd is "admin" if ever admin password will not work try to type in any password tht u can possibly use and after that u must be able to access the router's set-up page....
on the router's set-up page
click on wireless tab
change the ssid or network name to ur preferred network name like ur name or ur lastname...
after that click save settings and it will tell u if saving the settings is succesful.....
after that click again on wireless tab and click the wireless security tab
and then change the security mode to WPA personal or if ever u can't see the WPA personal click on WPA pre-shared key and type on the wpa pre-shared key box the network key for ur router it is like a password for ur network.....type in at least 8 characters....
and click save settings.....
and then close that window and try on ur wireless computer to view avaliable network and then refresh network list and look for ur network name and hit connect there the comp will ask for a network key type in there ur network key....
take care...
i'm not sure if it cn help u but just try to do so... -
Sqlplus can connect but can not work!
I have finished an installing of an Oracle10R2 on the OEL5.0 system. All run well except that the sqlplus can not work.I install it once more, but the results are same. What is the problem?
[oracle@localhost database]$ sqlplus
SQL*Plus: Release 10.2.0.1.0 - Production on Fri May 30 15:10:58 2008
Copyright (c) 1982, 2005, Oracle. All rights reserved.
Enter user-name: sys as sysdba
Enter password:
Connected to an idle instance.
SQL> startup
ORA-01078: failure in processing system parameters
LRM-00109: could not open parameter file '/u01/app/oracle/product/10.2.0/db_1/dbs/initorcl.ora'
SQL>
Message was edited by:
frank.qian[root@localhost admin]# whoami
root
[root@localhost admin]# set | grep -i ora
GTK_RC_FILES=/etc/gtk/gtkrc:/home/oracle/.gtkrc-1.2-gnome2
LOGNAME=oracle
MAIL=/var/spool/mail/oracle
OLDPWD=//u01/app/oracle/product/10.2.0/db_1/dbs
ORACLE_BASE=/u01/app/oracle
ORACLE_HOME=/u01/app/oracle/product/10.2.0/db_1
ORACLE_SID=orcl
PATH=/usr/kerberos/sbin:/usr/kerberos/bin:/usr/local/bin:/usr/bin:/bin:/usr/X11R6/bin:/home/oracle/bin:/u01/app/oracle/product/10.2.0/db_1/bin
PWD=//u01/app/oracle/product/10.2.0/db_1/network/admin
USER=oracle
USERNAME=oracle
[root@localhost admin]# la -l $ORACLE_HOME/bin/oracle
bash: la: command not found
[root@localhost admin]# ls -l $ORACLE_HOME/bin/oracle
-rwsr-s--x 1 oracle oinstall 93362188 May 30 14:56 /u01/app/oracle/product/10.2.0/db_1/bin/oracle
[root@localhost admin]# cat $ORACLE_HOME/network/admin/listener.ora
# listener.ora Network Configuration File: /u01/app/oracle/product/10.2.0/db_1/network/admin/listener.ora
# Generated by Oracle configuration tools.
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = /u01/app/oracle/product/10.2.0/db_1)
(PROGRAM = extproc)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(ADDRESS = (PROTOCOL = TCP)(HOST = localhost.localdomain)(PORT = 1521))
[root@localhost admin]# cat $ORACLE_HOME/network/admin/tnsnames.ora
# tnsnames.ora Network Configuration File: /u01/app/oracle/product/10.2.0/db_1/network/admin/tnsnames.ora
# Generated by Oracle configuration tools.
ORCL2 =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = localhost.localdomain)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = orcl2)
EXTPROC_CONNECTION_DATA =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(CONNECT_DATA =
(SID = PLSExtProc)
(PRESENTATION = RO)
[root@localhost admin]# ls -l $ORACLE_HOME/dbs
total 20784
-rw-r----- 1 oracle oinstall 168 May 29 10:10 alert_orcl.log
-rw-r----- 1 oracle oinstall 1544 May 29 21:27 hc_orcl0.dat
-rw-r----- 1 oracle oinstall 1544 May 30 08:31 hc_orcl1.dat
-rw-r----- 1 oracle oinstall 1544 May 30 14:58 hc_orcl2.dat
-rw-r----- 1 oracle oinstall 1544 May 27 12:49 hc_orcl.dat
-rw-r----- 1 oracle oinstall 12920 May 3 2001 initdw.ora
-rw-r----- 1 oracle oinstall 8385 Sep 11 1998 init.ora
-rw-r----- 1 oracle oinstall 24 May 30 15:00 lkORCL2
-rw-r----- 1 oracle oinstall 1536 May 30 15:04 orapworcl2
-rw-r----- 1 oracle oinstall 7061504 May 29 22:24 snapcf_orcl0.f
-rw-r----- 1 oracle oinstall 7061504 May 30 10:52 snapcf_orcl1.f
-rw-r----- 1 oracle oinstall 7061504 May 30 18:56 snapcf_orcl2.f
-rw-r----- 1 oracle oinstall 2560 May 30 16:29 spfileorcl2.ora
[root@localhost admin]# ps -ef | grep lsnr
oracle 8371 1 0 14:58 ? 00:00:00 /u01/app/oracle/product/10.2.0/db_1/bin/tnslsnr LISTENER -inherit
root 18146 5097 0 20:58 pts/2 00:00:00 grep lsnr
[root@localhost admin]# ps -ef | grep lsnr
oracle 8371 1 0 14:58 ? 00:00:00 /u01/app/oracle/product/10.2.0/db_1/bin/tnslsnr LISTENER -inherit
root 18146 5097 0 20:58 pts/2 00:00:00 grep lsnr
[root@localhost admin]# ps -ef | grep ora
root 2581 2560 0 14:15 ? 00:00:00 hald-addon-storage: polling /dev/hda
oracle 3542 3485 0 14:17 ? 00:00:00 /usr/bin/gnome-session
oracle 3605 3542 0 14:17 ? 00:00:00 /usr/bin/ssh-agent /usr/bin/dbus-launch --exit-with-session /etc/X11/xinit/Xclients
oracle 3608 1 0 14:17 ? 00:00:00 /usr/bin/dbus-launch --exit-with-session /etc/X11/xinit/Xclients
oracle 3609 1 0 14:17 ? 00:00:00 /bin/dbus-daemon fork print-pid 4 print-address 6 session
oracle 3615 1 0 14:17 ? 00:00:00 /usr/libexec/gconfd-2 11
oracle 3618 1 0 14:17 ? 00:00:00 /usr/bin/gnome-keyring-daemon
oracle 3620 1 0 14:17 ? 00:00:01 /usr/libexec/gnome-settings-daemon
oracle 3635 1 0 14:17 ? 00:00:14 metacity --sm-client-id=default1
oracle 3639 1 0 14:17 ? 00:00:02 gnome-panel --sm-client-id default2
oracle 3641 1 0 14:17 ? 00:00:01 nautilus no-default-window sm-client-id default3
oracle 3645 1 0 14:17 ? 00:00:00 /usr/libexec/gnome-vfs-daemon
oracle 3649 1 0 14:17 ? 00:00:00 /usr/libexec/bonobo-activation-server ac-activate ior-output-fd=17
oracle 3652 1 0 14:17 ? 00:00:00 eggcups --sm-client-id default4
oracle 3655 1 0 14:17 ? 00:00:00 gnome-volume-manager --sm-client-id default5
oracle 3660 1 0 14:17 ? 00:00:00 bt-applet --sm-disable
oracle 3675 1 0 14:17 ? 00:00:00 /usr/bin/python -tt /usr/bin/puplet
oracle 3677 1 0 14:17 ? 00:00:00 /usr/libexec/gam_server
oracle 3684 1 0 14:17 ? 00:00:00 ./escd key_Inserted="/usr/bin/esc" on_Signal="/usr/bin/esc"
oracle 3687 1 0 14:17 ? 00:00:00 /usr/libexec/trashapplet oaf-activate-iid=OAFIID:GNOME_Panel_TrashApplet_Factory oaf-ior-fd=19
oracle 3689 1 0 14:17 ? 00:00:06 /usr/libexec/wnck-applet oaf-activate-iid=OAFIID:GNOME_Wncklet_Factory oaf-ior-fd=25
oracle 3693 1 0 14:17 ? 00:00:00 /usr/libexec/mapping-daemon
oracle 3695 1 0 14:17 ? 00:00:00 nm-applet --sm-disable
oracle 3703 1 0 14:18 ? 00:00:00 pam-panel-icon --sm-client-id default0
oracle 3708 1 0 14:18 ? 00:00:01 gnome-power-manager
oracle 3712 1 0 14:18 ? 00:00:00 /usr/libexec/mixer_applet2 oaf-activate-iid=OAFIID:GNOME_MixerApplet_Factory oaf-ior-fd=23
oracle 3718 1 0 14:18 ? 00:00:01 /usr/bin/python -E /usr/bin/sealert -s
oracle 3728 1 0 14:18 ? 00:00:00 /usr/libexec/notification-area-applet oaf-activate-iid=OAFIID:GNOME_NotificationAreaApplet_Factory oaf-ior-fd=24
oracle 3730 1 0 14:18 ? 00:00:00 /usr/libexec/clock-applet oaf-activate-iid=OAFIID:GNOME_ClockApplet_Factory oaf-ior-fd=28
oracle 3766 1 0 14:18 ? 00:00:03 gnome-screensaver
oracle 3828 1 0 14:26 ? 00:00:09 gnome-terminal
oracle 3831 3828 0 14:26 ? 00:00:00 gnome-pty-helper
oracle 3832 3828 0 14:26 pts/1 00:00:00 bash
oracle 5067 3828 0 14:43 pts/2 00:00:00 bash
oracle 8371 1 0 14:58 ? 00:00:00 /u01/app/oracle/product/10.2.0/db_1/bin/tnslsnr LISTENER -inherit
oracle 9663 1 0 15:04 pts/1 00:00:00 /u01/app/oracle/product/10.2.0/db_1/perl/bin/perl /u01/app/oracle/product/10.2.0/db_1/bin/emwd.pl dbconsole /u01/app/oracle/product/10.2.0/db_1/localhost.localdomain_orcl2/sysman/log/emdb.nohup
oracle 10827 9663 0 15:06 pts/1 00:00:12 /u01/app/oracle/product/10.2.0/db_1/bin/emagent
oracle 11211 1 0 15:07 pts/1 00:00:11 /u01/app/oracle/product/10.2.0/db_1/jdk/bin/java -Djava.awt.headless=true -Doracle.oc4j.localhome=/u01/app/oracle/product/10.2.0/db_1/sqlplus -Djava.security.properties=/u01/app/oracle/product/10.2.0/db_1/oc4j/j2ee/home/config/jazn.security.props -jar /u01/app/oracle/product/10.2.0/db_1/oc4j/j2ee/home/oc4j.jar -config /u01/app/oracle/product/10.2.0/db_1/oc4j/j2ee/isqlplus/config/server.xml
oracle 11427 1 0 15:10 ? 00:00:00 /bin/sh /usr/lib/firefox-1.5.0.9/firefox
oracle 11450 11427 0 15:10 ? 00:00:00 /bin/sh /usr/lib/firefox-1.5.0.9/run-mozilla.sh /usr/lib/firefox-1.5.0.9/firefox-bin
oracle 11455 11450 2 15:10 ? 00:10:14 /usr/lib/firefox-1.5.0.9/firefox-bin
oracle 12851 1 0 15:29 ? 00:00:00 ora_pmon_orcl2
oracle 12853 1 0 15:29 ? 00:00:00 ora_psp0_orcl2
oracle 12855 1 0 15:29 ? 00:00:00 ora_mman_orcl2
oracle 12857 1 0 15:29 ? 00:00:00 ora_dbw0_orcl2
oracle 12859 1 0 15:29 ? 00:00:02 ora_lgwr_orcl2
oracle 12861 1 0 15:29 ? 00:00:00 ora_ckpt_orcl2
oracle 12863 1 0 15:29 ? 00:00:06 ora_smon_orcl2
oracle 12865 1 0 15:29 ? 00:00:00 ora_reco_orcl2
oracle 12867 1 0 15:29 ? 00:00:00 ora_cjq0_orcl2
oracle 12869 1 0 15:29 ? 00:00:02 ora_mmon_orcl2
oracle 12871 1 0 15:29 ? 00:00:00 ora_mmnl_orcl2
oracle 12873 1 0 15:29 ? 00:00:00 ora_d000_orcl2
oracle 12876 1 0 15:29 ? 00:00:00 ora_s000_orcl2
oracle 12884 1 0 15:29 ? 00:00:00 ora_rvwr_orcl2
oracle 12886 1 0 15:29 ? 00:00:00 ora_arc0_orcl2
oracle 12888 1 0 15:29 ? 00:00:00 ora_arc1_orcl2
oracle 12895 1 0 15:29 ? 00:00:00 ora_qmnc_orcl2
oracle 12966 1 0 15:29 ? 00:00:10 oracleorcl2 (LOCAL=NO)
oracle 12975 1 0 15:29 ? 00:00:02 oracleorcl2 (LOCAL=NO)
oracle 12978 1 0 15:29 ? 00:00:00 ora_q000_orcl2
oracle 12982 1 0 15:29 ? 00:00:00 ora_q002_orcl2
oracle 12989 9663 2 15:29 pts/1 00:08:04 /u01/app/oracle/product/10.2.0/db_1/jdk/bin/java -server -Xmx256M -XX:MaxPermSize=96m -XX:MinHeapFreeRatio=20 -XX:MaxHeapFreeRatio=40 -DORACLE_HOME=/u01/app/oracle/product/10.2.0/db_1 -Doracle.home=/u01/app/oracle/product/10.2.0/db_1/oc4j -Doracle.oc4j.localhome=/u01/app/oracle/product/10.2.0/db_1/localhost.localdomain_orcl2/sysman -DEMSTATE=/u01/app/oracle/product/10.2.0/db_1/localhost.localdomain_orcl2 -Doracle.j2ee.dont.use.memory.archive=true -Djava.protocol.handler.pkgs=HTTPClient -Doracle.security.jazn.config=/u01/app/oracle/product/10.2.0/db_1/oc4j/j2ee/OC4J_DBConsole_localhost.localdomain_orcl2/config/jazn.xml -Djava.security.policy=/u01/app/oracle/product/10.2.0/db_1/oc4j/j2ee/OC4J_DBConsole_localhost.localdomain_orcl2/config/java2.policy -Djava.security.properties=/u01/app/oracle/product/10.2.0/db_1/oc4j/j2ee/home/config/jazn.security.props -DEMDROOT=/u01/app/oracle/product/10.2.0/db_1/localhost.localdomain_orcl2 -Dsysman.md5password=true -Drepapi.oracle.home=/u01/app/oracle/product/10.2.0/db_1 -Ddisable.checkForUpdate=true -Djava.awt.headless=true -jar /u01/app/oracle/product/10.2.0/db_1/oc4j/j2ee/home/oc4j.jar -config /u01/app/oracle/product/10.2.0/db_1/oc4j/j2ee/OC4J_DBConsole_localhost.localdomain_orcl2/config/server.xml
oracle 13020 1 0 15:30 ? 00:00:01 oracleorcl2 (LOCAL=NO)
oracle 13028 1 0 15:30 ? 00:00:01 oracleorcl2 (LOCAL=NO)
oracle 13031 1 0 15:30 ? 00:00:09 oracleorcl2 (LOCAL=NO)
oracle 13148 1 0 15:32 ? 00:00:10 oracleorcl2 (LOCAL=NO)
oracle 16447 3832 0 18:50 pts/1 00:00:00 sqlplus
oracle 16448 16447 0 18:50 ? 00:00:00 oracleorcl2 (DESCRIPTION=(LOCAL=YES)(ADDRESS=(PROTOCOL=beq)))
oracle 18165 1 14 21:00 ? 00:00:00 ora_j000_orcl2
root 18167 5097 0 21:00 pts/2 00:00:00 grep ora
[root@localhost admin]# tail /u01/app/oracle/admin/orcl/bdump/alert.log
tail: cannot open `/u01/app/oracle/admin/orcl/bdump/alert.log' for reading: No such file or directory
[root@localhost admin]# tail /u01/app/oracle/admin/orcl2/bdump/alert.log
tail: cannot open `/u01/app/oracle/admin/orcl2/bdump/alert.log' for reading: No such file or directory
Maybe you are looking for
-
I have used BlazeDS in an application to push the data in realtime. However, we have been experiencing a heavy memory leak in the application. The application has a scheduler that pushes the data every one minute into the default queue. Without a
-
Super slow GUI - where to look?
Hi I've got a GUI with a Jtree which has a root node and then clubs and then members. root - club -- member1 -- member2 - club -- member1 My question concerns the way its not running, although the treeModel seems to be working it is so slow I can mak
-
Hi, i have to use xerces with oc4j but i get such an error when starting the application server: org.apache.commons.digester.Digester - Digester.getParser: org.xml.sax.SAXNotRecognizedException: http://apache.org/xml/features/validation/dynamic at or
-
Same problem with Premiere Elements 13
-
Why did apple trailers and quicktime stop working together all of a sudden?
I'm running Chrome and Firefox and Apple Trailers suddenly stopped launching HD trailers through Quicktime X. It was working automatically a few weeks ago. The only info i can find on the net is years old. Anyone else having this problem? Anyone fix