Content Engine CE565 authentication cache
I have a Content Engine CE565 running software version CE 5.1.7
The commands <show users request-authenticated> and <show http-authcache> provide me with information on authenticated users, but I would like to know how to determine the time remaining for a user/ip address in the authcache. This is with the understanding that the authentication will timeout after the configured period of inactivity (in minutes).
Also, is there a way to remove the authentication cached for single user/ip address? Understanding that the authentication cache resides in RAM. The only command that I am aware of is <clear users request-authenticated>, which clears all authenticated users. However, this requires all users to reauthenticate. TIA
As far as I know, there is no way to clear a single user, only all of them by using the command you mentioned above. The command http authentication cache timeout can be used to configure the time between last access and cache removal.
Similar Messages
-
Content Engine cannot authenticate using LDAP
Dear All,
I have a problem with content engine 511 authenticating with LDAP server. I am using Lotus notes LDAP server to authenticate with content engine but it doesn't work. Anyone has try with LDAP before? Please advice. Thank you for your help.
Regards,
ChrisDear,
I already using the latest version of ACNS software 5.3. And there is an option to use LDAP authentication in CLI and WEB based management. Thank you for your help.
Regards,
Chris -
Content engine 510 - transparent proxy stand-alone
Hello to all,
after studying architecture examples about Content Engine 510, I found that there is two modes:
1) standard proxy
2) transparent proxy
I need the transparent architecture !
But every example about transparent mode seems to include a router or a switch with a particular level of software, that can send http requests to the Content Engine to have cache.
I don't have any of these components.
I simply need to have a Content Engine that receive any kind of IP protocols on one ethernet, and route it to the other ethernet plug, except that if it is http protocol, it will cache the pages.
Is is simply impossible to configure the Content Engine 510 that way ?
Is the transparent proxy mode always requires a router or a switch to give it the http flow ?
If it is possible, where can I find some configuration examples ?
Thanks to help a newbie in content engine...
OlivierOlivier,
You'll need to have a router running wccp in order to redirect http requests to the cache. Withouth this, the cache has no visibilty of traffic on your LAN.
Regards,
Dave -
Content Engine Network Module for Caching File Server Objects
We have a content engine network module for a 2821 router located at a branch office that we'd like to use for clients to obtain locally cached file objects from a Windos server located at our headquarters or corporate office. I've been looking for some sample configs or documentation that will show me that this is possible and on how to do it since this is my first time ever doing. All I was able to find so far was the link below under "Support of Preloading of NTLM Authenticated Objects", but it seems incomplete in providing configuration tasks that most CCO doc's usually provide. Has anyone else had any luck finding some useful doc's or sample configs to get this accomplish? Thanks in advance.
http://www.cisco.com/univercd/cc/td/doc/product/webscale/uce/acns55/55ldg/urlfiltr.htm#wp1158213You can't cache Windows Files using the Cache Engines.
You CAN do this using WAFS though. I'd suggest looking at the WAFS (or upcoming WAAS) products, which use WCCP like the Cache Engines to transparently redirect Windows File Sharing requests. -
Content Engine caching video content?
I am currently running ACNS version 5.5.11.2 on a CE510 Content Engine. I recently had to replace the unit and when I set up the partitions for the new build, I elected to go with CE510#disk config sysfs 10% cfs 45% mediafs 45%.
Before the cfs was setup to use the whole box. I was thinking that the mediafs partition would start to cache video content. Does that happen automatically or is there some other setting to make that happen further. How do I determine if it is getting any use?A content engine can cache files transfered via ftp but not https [as the content is encrypted].
It can cache whatever file, including video, audio, ...
Content routing, content switching are just names.
They refer to how the traffic will be intercepted and forwarded to the content engine.
You could simply use a proxy solution and have your users setup their browser to use the content engine as a proxy, or you could transparently intercept http/ftp traffic via a router running wccp, or you could use a Layer7 device like a CSS to intercept the traffic and redirect to the content engine.
Regards,
Gilles. -
Graceful Shutdown of a Content Engine (CE510, CE565)
May I come back to y.lo's message from January this year. He asked for a shutdown or halt command for CEs.
There is a possibility to shutdown the NM-CE-BP (network module) with the service-module command form the IOS. There must be something similar in ACNS! In the manuals there is quite often a referenc to "orderly shutdown" or "gracefully shutdown", but I couldn't find the appropriate command anywhere near these references.
Thanks.Its not exactly graceful but I've always done a reload with the console plugged in, then when the BIOS messages come up for accessing the flash (before the disk scan), I power it off. The theory is the disks have been cleanly shutdown and the linux subsystem will flushed the filesystems and the content engine isn't actually running. If there is a command I'd like to know it as well.
regards
Mark -
Zero hit for caching on content engine, why?
"show statistics http savings" reveals there's zero (0) hit for web requests.
"show statistics http miss-reason"
indicates most of them was due to "none_get_method".
Now, what does that mean, and how can I increase the hits?
We're using the exact same rules as all the other sites (which have hits), except we're redirecting traffic on the ingress interface instead of egress:
int g0/0.1
ip wccp web-cache redirect in
Any ideas please share.
thanks.Hi,
There are many reasons why a CE is not caching content, I'll try to list some of the things you may check:
- Make sure that the router is indeed redirecting traffic to the CE, use this command on the router: sh ip wccp web-cache detail. Make sure that the redirect line is constantly increasing.
- Make sure that the CE has a CFS partition configured, use this output on the CE to check: sh disk details. Look for the CFS partition and make sure it has some space allocated. If you need to partition the disk, use this command: 'disk config sysfs 5% cfs 50% mediafs 30% cdnfs remaining'.
- Add this command to the CE: http cache-cookies. This would greatly increase the amount of content that would be cached by the CE.
- Another thing that needs to be considered is the web site you are going to. Remember that dynamic content would not be cached by the CE.
Check these points and if you continue having issues, add a sh tech from the CE for review and a tcpdump taken at the CE using this command: '#tcpdump -s 1500 -w dump.cap'. Get the file 'dump.cap' off the CE.
Let me know how it goes. Thanks!
Regards,
Jose Quesada. -
Content Engine NM ACNS/network access
After searching Google and Cisco, here's my setup...
2851 Router running 15.1T
CE-NM-BP-80G-K9 in slot 1/0
Bridge group 1 for LAN and Wireless WIC.
Goal: Either add the external CE interface to the LAN on the bridge group or use WCCP to cache traffic through the internal interface.
I was able to access ACNS once, but I'm completely new to the design and it was only for testing with the IP scheme. I reset the config, reloaded the router and now I can't access ACNS via the web gui nor can I access the network from the CE (ping or ftp).
Interface ContentEngine 1/0 Config:
ip address 10.0.0.1 255.255.255.0
Service Module ip address 10.0.0.2 255.255.255.0
Service Module external ip address 10.0.1.1 255.255.255.0
Service Module ip default gateway 10.0.0.1
Interface BVI1
ip address 192.168.2.1 255.255.255.0
using dhcp etc
Service module config:
CE#sh run
! ACNS version 5.5.3
hostname CE
http proxy incoming 80 8080
ip domain-name mydomain.com
interface FastEthernet external
exit
interface FastEthernet internal
exit
wmt evaluate
wmt accept-license-agreement
wmt enable
ip name-server 8.8.8.8
ip name-server 192.168.2.1
wccp router-list 1 192.168.2.1
wccp web-cache router-list-num 1
wccp reverse-proxy router-list-num 1
wccp wmt router-list-num 1
wccp version 2
username admin password 1 xxx
username admin privilege 15
username xxxx password 1 xxx uid 2001
username xxxx privilege 15
authentication login local enable primary
authentication configuration local enable primary
cdm ip 192.168.2.1
! End of ACNS configuration
Here's what I get when attempting to ping:
CE#ping 192.168.2.1
connect: Network is unreachable
CE#ping 10.0.0.1
connect: Network is unreachable
CE#ping 10.0.1.1
connect: Network is unreachable
And from the LAN:
seth@Sony:~$ ping 192.168.2.1
PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data.
64 bytes from 192.168.2.1: icmp_req=1 ttl=255 time=1.79 ms
^C
--- 192.168.2.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 1.799/1.799/1.799/0.000 ms
seth@Sony:~$ ping 10.0.0.1
PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data.
64 bytes from 10.0.0.1: icmp_req=1 ttl=255 time=1.39 ms
64 bytes from 10.0.0.1: icmp_req=2 ttl=255 time=1.93 ms
^C
--- 10.0.0.1 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1001ms
rtt min/avg/max/mdev = 1.396/1.666/1.936/0.270 ms
seth@Sony:~$ ping 10.0.0.2
PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.
^C
--- 10.0.0.2 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 1006ms
seth@Sony:~$ ping 10.0.1.1
PING 10.0.1.1 (10.0.1.1) 56(84) bytes of data.
^C
--- 10.0.1.1 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 1007ms
Page cannot be displayed when attempting to hit the CE on port 8001 or securely at 8003 although the CE shows it's listening
CE#sh gui-server
GUI Server is enabled
Listen on port 8001
Secured GUI Server is enabled
Secured GUI Listen on port 8003
Let me know if there's some other pertinent info, but what am I missing?SOLVED --
The mistake was my own...in writing this post and re-testing, I realized I had made a foolish mistake. I applied an access-list (which I forgot to include) to the "ip wccp web-cache redirect-list bypass_content_engine" in the global config of the router.
When I installed service 95 for spoofing, I automatically added the same access list to it as well.
This was not a good thing since the access list denied packets with a destination of our internal IP addresses from going through the content engine. This worked fine on the way *out* of the router. But as the now-spoofed packets returned, their destination was an inside IP address and they were pretty much discarded. Foolish Mistake!
Removing the ACL from the "ip wccp 95" statement in the global config fixed the issue and I am spoofing fine.
Sorry to waste time...
David Hunter -
Dear All,
My apologies if this posting is on the wrong board.
I've a problem with our content engine returning an error of:
"Tre reply from server is not valid"
The URL of the site is http://hiring.monster.co.uk/jobs/createtitle.aspx?mode=qb.
I've attached a screenshot of the error message.
Any advice or help would be greatly appreciated.
Thank you in advance.
SinhThis symptom is observed on a router on which Web Cache
Communication Protocol (WCCP) is enabled and Cisco Express Forwarding (CEF)
switching is disabled. If the caches are Cisco caches, they will be running
software prior to ACNS 4.2.5.
solution: Ensure that CEF switching is enabled on the router. If this is not possible, the impact of the problem on the cache will be minimized if the authentication bypass function is disabled.also try upgrading IOS to 12.1(18.01)E which may solve the issue. -
Smartfilter with Content Engine Module (NM-CE-BP-40G-K9) & ACNS on 3661
I've been looking over the CCO docs, but can't find one that has sample configs for using a 3661 router containing content engine module, smartfilter, & ACNS. Topology is basically the following...
(PC's)----(LAN Switch)-----(3661 w/content engine module)----(PIX)---(internet)
I don't want to creat a new IP subnet for the 3 interfaces within the content engine module/router. I want to use the IP's from the current LAN IP Block.
Any advice appreciated.I thought this might help.
Easy NM-CE Configuration Guide!
Router IOS:c3725-ik9o3s-mz.122-15.T2
Content Engine Software: ACNS 5.0.3.5
Configure basic router configuration as normal.
Set the IP addresses for the Service Module (Content-Engine) using these commands:
interface Content-Engine2/0
ip address 10.1.1.1 255.255.255.0
ip nat inside
service-module external ip address 10.0.0.1 255.255.255.0
service-module ip address 10.1.1.2 255.255.255.0
service-module ip default-gateway 10.1.1.1
Complete Config Example (DHCP and NAT for Lab):
urrent configuration : 2440 bytes
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname lab3745_NM-CE
logging queue-limit 100
enable password cisco
ip subnet-zero
ip wccp web-cache
ip dhcp pool NM-ESW-16-POOL
network 10.1.2.0 255.255.255.0
domain-name cisco.com
default-router 10.1.2.1
dns-server 171.68.226.120 171.70.168.183
lease 7
ip audit notify log
ip audit po max-events 100
no voice hpi capture buffer
no voice hpi capture destination
mta receive maximum-recipients 0
interface FastEthernet0/0
ip address 172.16.12.108 255.255.255.0
ip wccp web-cache redirect out
ip nat outside
duplex auto
speed auto
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface FastEthernet1/0
no ip address
interface FastEthernet1/1
no ip address
interface FastEthernet1/2
no ip address
interface FastEthernet1/3
no ip address
interface FastEthernet1/4
no ip address
interface FastEthernet1/5
no ip address
interface FastEthernet1/6
no ip address
interface FastEthernet1/7
no ip address
interface FastEthernet1/8
no ip address
interface FastEthernet1/9
no ip address
interface FastEthernet1/10
no ip address
interface FastEthernet1/11
no ip address
interface FastEthernet1/12
no ip address
interface FastEthernet1/13
no ip address
interface FastEthernet1/14
no ip address
interface FastEthernet1/15
no ip address
interface Content-Engine2/0
ip address 10.1.1.1 255.255.255.0
ip nat inside
service-module external ip address 10.0.0.1 255.255.255.0
service-module ip address 10.1.1.2 255.255.255.0
service-module ip default-gateway 10.1.1.1
interface Vlan1
ip address 10.1.2.1 255.255.255.0
ip nat inside
ip local pool NM-ESW-16-POOL 10.1.2.2 10.1.2.254
ip nat pool TEST-NAT-POOL 172.16.12.108 172.16.12.108 prefix-length 24
ip nat inside source list 7 pool TEST-NAT-POOL overload
ip http server
no ip http secure-server
ip classless
ip route 0.0.0.0 0.0.0.0 172.16.12.254
access-list 7 permit 10.1.2.0 0.0.0.255
access-list 7 permit 10.1.1.0 0.0.0.255
access-list 7 permit 10.0.0.0 0.0.0.255
call rsvp-sync
mgcp profile default
dial-peer cor custom
line con 0
speed 115200
line 65
flush-at-activation
no activation-character
no exec
transport input all
line aux 0
line vty 0 4
password cisco
login
end
reset service-module 2 to reboot the Content-Engine:
service-module content-Engine 2/0 reload
Within 30 Seconds Session from the Router to the Service Module:
service-module content-engine session
Enter Basic Configuration for Network Module:
Password, etc
Configure The service Modeule using the command line interface:
hostname NM-CE-BP
ip domain-name CISCO.COM
interface FastEthernet 0/0
ip address 10.0.0.1 255.255.255.0
exit
interface FastEthernet 0/1
ip address 10.1.1.2 255.255.255.0
exit
ip default-gateway 10.1.1.1
primary-interface FastEthernet 0/1
ip name-server 172.72.1.1
wccp router-list 1 172.16.12.108
wccp web-cache router-list-num 1
wccp version 2
username xxx password xxxx
username xxxx privilege 15
authentication login local enable primary
authentication configuration local enable primary
NM-CE-BP#exit
You can use the command line interface to show statics from the Content Engine by using the show statistics screen command or use your web browers for a more graphical report. -
Saturation on Content engine CE-565 and Smartfiler log
Hi, with content engine CE-565-K9
we have the following message log on the smartfilter:
"Jun 25 08:19:03 cer44sec-pxy2.cer44.recouv cache: %CE-UNKNOWN-4-899999: too many jobs in plugin thread pool queue (1001). Maximum allowed is: 1000
Jun 25 08:19:03 cer44sec-pxy.cer44.recouv cache: %CE-UNKNOWN-3-899999: Failed to start job to look up groups for user 'UR49100640'"
I can't see how is limited the thread number on the CE565. So who can explain to me the signification of this log and/or how configring the maximun thread on the CE565.
Thank's
MichelSmartfilter uses a pool of 20 threads for LDAP lookups. What this error indicates is that the number of outstanding LDAP requests has grown to more than 1000 which is the limit supported.
-
Should the Cisco Content Engines be used as a proxy appliance
Should the Cisco Content Engine be use as a proxy appliance like a Blue Coat appliance, Squid cache engine, ISA server, etc...
I am pretty sure it is but just need some feedback on past experiences. Customer would like to by a Cisco product for Web filtering/proxy.
or is it strictly used to help with web base applications.HI,
the CE is basically able to check every request it supports. If you are using 3rd level products like smartfilter, websense or webwasher you can use the features of those products to supress/forbid certain requests(i.e MSN etc.)
Kind Regards,
Joerg -
Help!!! Content engine
my configuration is follow the attached file. I don't know what is wrong with my content engine using as a cache server. when i connect this CE to my network, i can make my user access to the internet fast only 2 days, but after 2 days it makes my users internet connection slow. So when users access to the internet slow, i disconnect this CE from my network, then my users internet connections is running better. So please help me to find what is incorrect with my configuration and what commands i should add more to this current configuration"
What is the ACNS software version u r using in ur content Engine7305.I am sending u a configuration doc for ACNS rlease 5.2.This has all the info regarding ACNS 5.2.
http://www.cisco.com/en/US/products/sw/conntsw/ps491/products_configuration_guide_book09186a00802debd6.html
Let me know, if you have any problem in browsing this big document. and finding out the pblm.I will assist you. -
Should the Content Engine work while the Inernet link is down ?
I have installed CE590 in a client network
The http saving performance is from 30 : 40 %
My client want to make sure the CE is caching the web site
He want to shutdown Serial port of the main router , and try to browse web sites. ( the Cached sites )
Should he get a reply from the CE and browse the cached sites ??
I mean , Can the PC browser ( while the internet is link is down ) open page like www.yahoo.com for example if it is cached on the CE ??
Is there is any command of the CE that can display the name of the cahced web pages ?
Note : Cisco Content Engine Software Release 3.11
Can anyone help me ?
Thanks
Mohamed AbdallahMohamed,
Before you go any futher you need to upgrade the CE to ACNS 4.2.3. There are known issues with 3.1.1.
To answer your question the CE will only server content if it can not access the internet if the object is fresh. By this I mean the object has not expired or the object does not need revalidation eg If modified since request.
This could cause problems with broken pages etc etc.
Your best option is to turn on transaction logging.
transaction-logs enable
You can then go to the local1/logs directory on the CE
type working.log
This will show you the urls that clients are requesting and if they got a hit / miss/ ims hit / ims miss etc etc.
Overall your cache should always have access to the origin server for content.
Cheers
Phil -
Hi there,
I'm having some problems with Content Engine.
I would appreciate any help.
It gives following errors:
Jun 12 08:15:59 CE01 wccp: %CE-WCCP-5-500008: WCCP: A new view from
the 25.25.25.25. Change number = 28
Jun 12 08:15:59 CE01 wccp: %CE-WCCP-5-500014: WCCP: New CE notified of
15.16.17.208
Jun 12 08:15:59 CE01 wccp: %CE-WCCP-5-500026: New CE entry being
created for 15.16.17.208 seen by router 25.25.25.25
Jun 12 08:16:07 CE01 wccp: %CE-WCCP-4-500015: WCCP:No assignment sent:
15.16.17.204 not in Router View
Jun 12 08:16:08 CE01 wccp: %CE-WCCP-5-500008: WCCP: A new view from
the 25.25.25.25. Change number = 29
Jun 12 08:16:08 CE01 wccp: %CE-WCCP-5-500014: WCCP: New CE notified of
15.16.17.204
Jun 12 08:16:08 CE01 wccp: %CE-WCCP-5-500026: New CE entry being
created for 15.16.17.204 seen by router 25.25.25.25
Jun 12 08:16:17 CE01 wccp: %CE-WCCP-5-500019: WCCP: New WC in compute
assign 15.16.17.204
Jun 12 08:16:40 CE01 wccp: %CE-WCCP-3-500001: HTTP Proxy may be down,
keepalives halted!
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct got error :
50 for key stat/cache/http/perf/throughput/requests/sum connection 5
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct: unable to
get `stat/cache/http/perf/throughput/requests/sum' from dataserver
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: unable to get http
request throughput stats(error 50)
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct got error :
4 for key stat/cache/https/request connection 5
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct: unable to
get `stat/cache/https/request' from dataserver
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: unable to get https
request throughput stats(error 4)
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct got error :
4 for key stat/cache/ftp connection 5
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct: unable to
get `stat/cache/ftp' from dataserver
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: unable to get
ftp-over-http request throughput stats(error 4)
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct got error :
4 for key stat/cache/http/usage/cpu/sum connection 5
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: ds_getStruct: unable to
get `stat/cache/http/usage/cpu/sum' from dataserver
Jun 12 08:20:54 CE01 java: %CE-CMS-4-700001: unable to get cpu
stats(error 4)Hi guys,
I am really out of ideas!!!
I've updated software couple times already.
but nothing helps.
it still gives same error:
Jun 16 14:23:01 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/http/usage/cpu/sum not found not found in dataserver
Jun 16 14:23:01 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/http/request not found not found in dataserver
Jun 16 14:23:01 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/https/request not found not found in dataserver
Jun 16 14:23:01 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/https/requests not found not found in dataserver
Jun 16 14:23:01 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/ftp-native not found not found in dataserver
Jun 16 14:23:01 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/ftp not found not found in dataserver
Jun 16 14:23:02 ponent exec_show_stats: %CE-CLI-3-170013: item stat/wccp/bypass not found not found in dataserver
Jun 16 14:23:02 ponent exec_show_stats: %CE-CLI-3-170013: item stat/wccp/bypass not found not found in dataserver
Jun 16 14:23:52 ponent exec_rule: %CE-CLI-3-170013: Verifier not responding. when setting cfg/gl/cache/rule/stat/show (Error number: 32)
Jun 16 14:23:52 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/http/err not found not found in dataserver
Jun 16 14:23:52 ponent exec_show_stats: %CE-CLI-3-170013: item stat/cache/https/err not found not found in dataserver
Jun 16 14:24:37 ponent cfg_bin_urlfilter: %CE-CLI-3-170013: Verifier didn't respond. Need to re-register verifier. when setting /cfg/gl/cache/urlfilter/http/enable (Error number: 64)
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct got error : 4 for key stat/cache/http/perf/throughput/requests/sum connection 5
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct: unable to get `stat/cache/http/perf/throughput/requests/sum' from dataserver
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: unable to get http request throughput stats(error 4)
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct got error : 4 for key stat/cache/https/request connection 5
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct: unable to get `stat/cache/https/request' from dataserver
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: unable to get https request throughput stats(error 4)
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct got error : 4 for key stat/cache/ftp connection 5
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct: unable to get `stat/cache/ftp' from dataserver
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: unable to get ftp-over-http request throughput stats(error 4)
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct got error : 4 for key stat/cache/http/usage/cpu/sum connection 5
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: ds_getStruct: unable to get `stat/cache/http/usage/cpu/sum' from dataserver
Jun 16 14:24:45 ponent java: %CE-CMS-4-700001: unable to get cpu stats(error 4)
Jun 16 14:24:47 ponent java: %CE-CMS-4-700001: ds_getStruct got error : 4 for key stat/cache/http/perf/throughput/requests/sum connection 5
Jun 16 14:24:47 ponent java: %CE-CMS-4-700001: ds_getStruct: unable to get `stat/cache/http/perf/throughput/requests/sum' from dataserver
Jun 16 14:24:47 ponent java: %CE-CMS-4-700001: unable to get http request throughput stats(error 4)
Jun 16 14:25:15 ponent cfg_bin_urlfilter: %CE-CLI-3-170013: Verifier didn't respond. Need to re-register verifier. when setting /cfg/gl/cache/urlfilter/http/enable (Error number: 64)
Jun 16 14:25:24 ponent writemem.sh: %CE-CLI-2-170054: running-config has 0 line(s)
Jun 16 14:25:24 ponent exec_copy: %CE-CLI-3-170055: Copy running-config to startup-config failed!. status(1.20)
please, any suggestion would be appreciated.
Maybe you are looking for
-
I need help trying to download music to three different devices. iPod5, 2iPhone 4s, one of which is the main name on account. However when I go to plug one of the 4s' in the computer, it starts to sync to my own "named" device, my itunes acct.(needle
-
Additional field in SAP Infoset - internal table
Hi Gurus, I have invoices like: VBELN Matnr mtart 1234 Ek21 MCFE 1234 Ek33 MCFE 1234 Ek29 MCFE 1234 321 MRM1 1235 EK11 MCFE 1235 EK17 MCFE 3212 EK23
-
Software update for my Product Code
I guess my product code is 0596011 but I'm not very sure. When are you gonna release the 52.0.007 firmware for my phone? I need to know if releasing will take days, weeks, months or years, because I can't wait. Thank you .
-
Calendar question re: times
I am not sure this is the right board for this question, but I could not find one that was appropriate. I would like to know how to make the items I list on the palm desktop calendar be in order by time of day, but they are always haphazard. Will ap
-
Qosmio X870 shutting down without reason - low perfs
Hello everyone, I have recently bought a Qosmio X870 116 and I am extremely disappointed. It is supposed to be a gaming computer but I can barely run a single game without the PC crashes. I tried to run recent games such as Diablo 3 and Guild Wars 2.