Control the total time for a quiz
I find in Captivate 4 it is possible set time limit for individual question. However, it is more useful for me to set a time limit for the whole quiz. I cannot find such setting in quiz preference. Can we do that without any customization by AS coding?
It is possible to set a time limit in CP-quizzes, if you are creating a SCORM-object (for a LMS) by settings in the Manifest file: under SCO as you can see in this image:
But honestly I believe it is much better to set time limits in the LMS itself (supposing you are deploying the quiz through a LMS).
Lilybiri
Similar Messages
-
How to control the looping time of the for loop in 10 microseconds in labview?
I need to create a +/- 9 volt square wave with period of 20us using a D/A card (Not NI card). I can write command to the card using outport provide by Labview. Right now, I can generate square wave with 4ms period which is limited by the resolution of the wait until next ms icon I used inside the for loop. Could anyone tell me how to control the execution time of the for loop to about 10 us? Your help would be much appreciated.
I'm not sure if this will hep, but this answer seems to answer this question
http://exchange.ni.com/servlet/ProcessRequest?RHIVEID=101&RPAGEID=135&HOID=50650000000800000029410000&UCATEGORY_0=_30_%24_12_&UCATEGORY_S=0&USEARCHCONTEXT_QUESTION_0=microsecond+resolution+1ms&USEARCHCONTEXT_QUESTION_S=0 -
Finding the total time or total frames for FLV?
Is there some properties box somewhere that will tell me the
total number of frames or total time for an FLV? I can see the time
after I encode the files, but that information doesn't seem to
stick around.
Thanks.You can see the time length of an FLV clip in your Library by
right clicking the file name and chosing Properties from the menu.
Hope that helps! -
How do you display total time for playlist in Itunes 11
how do you display total time for playlist in Itunes 11
"I can see the total time in my playlist on the computer but not on my device??"
I have just posted a question asking the same!
Did you have any joy? -
Pxie-6556 - How to control the rise time in the digital lines (hsdio)
Hi,
Is there any way to control the rise time in the PXIe-6556 digital lines?
Even in a low frequency signal 10kHz the rise time is about 2ns.
Tks,
Solved!
Go to Solution.Hello engfpe,
The PXIe-6556 is a 50 Ohm system, meaning the output is source series terminated to be 50 Ohms and all our cables and accessories are 50 Ohms. With this setup regardless of the data rate you should have a clean rising or falling edge regardless of the data rate. The quality of the output (rising or falling edge) at your device will be related to the impedance matching of your cables.
The PXIe-6556 cannot adjust the slew rate by itself. However you can insert some simple passive components to do this for you. I've attached below to images. The first is a schematic showing one way of slowing down the edge. The second is the a simulated waveform showing the original edge rate before slowing it down, and the slowed down edge. This simulation is not of the PXIe-6556 but instead a generic digital output for concept. In the schematic R1 is set to 34 Ohms because U1.8 has the additional 16 Ohms inside it. TL1 is the 50 Ohm output simulating the cable on the PXIe-6556. R2, R3 and C1 are components you could insert after the PXIe-6556 cable before it goes to your device/cables. In this setup the cable going to your device is TL2 which is also 50 Ohms but it could be another impedance in which case you would change R3 to match.
You can see in the attached images you can significantly slow down the edge with this setup by altering C1. I hope this helps,
Jesse O. | National Instruments R&D
Attachments:
edge_compare_schematic.jpg 94 KB
edge_compare_waveform.jpg 44 KB -
[Urgent!!]How to control the running time??
Hi,
I'm an undergraduate researcher in the University of Michigan. I used NI labVIEW FPGA on my current project and now i meet a problem.
I have a labview code that has runs with 3 subroutines. they execute one after another for a given time period for each iteration of the entire code. that is i built them in a flat sequence structure inside a large while loop and each of the subroutine is a while loop with several subvi's in it. not that complicated but i have to specify how long each subroutine runs. now i have a problem to set that execution time. i don't know exactly what kind of timing function i shall use. i tried the "Elapsed time" function but that only works for the first iteration. from the second iteration on each subroutine only runs for once, instead of continuing to run until the given time elapsed. so i don't know how to correctly control the running time. It's reallly urgent, so could you please give me some suggestions about it? Thanks a million!!
XiaofeiThank you for your suggestion!
sorry but that this method won't help because my code is sort of difficult to put into a for loop .
the logic is like this: first the output is set to 0 for a user-defined amount of time (means no excitation). secondly it gets excitation and gets output but no data saving is allowed for a user-defined amount of time. at the same time, one paramater is automatically changed. (the reason for not saving data is that there is a transient response when the parameter changes). thirdly, data saving begins with the same
parameters as before, also for a user-defined amount of time. and then after these three steps one iteration is done. for iterations there is a different parameter, the user defines the range of the parameter and the number of different values in between and the code will do the increment at equal intervals automatically. my problem now is that i don't know how to correctly control the time. i have tried various ways but no one works.
the second problem is that i don't know how to let it run and not saving data and then saving data without changing everything else. what i have now is to call the same VI twice, once for only running and no data saving and the other for saving data. but then the problem is that in between these two routines, the output suddenly becomes zero and gets excited again after i call it. My professor said that i cannot let the output become zero, otherwise there is no meaning in waiting for the excitation to become stablee. but then i don't know how to call a VI only once and let it do the saving for only the latter part of the running time. i have been working on this thing for two weeks now and still have no idea....Sorry the problem is long and tedious, but if anyone have any idea about it, please let me know, i will be most grateful. Thanks a million!!! -
How to insert, as an input variable within formula, the total time window on scope?
How to insert, as an input variable within formula, the total time window on scope (i.e. 20ms/div x 10 div = 200ms)?
BELOW IS AN EXAMPLE OF ISSUE:
FORMULA FOR ACTION INTEGRAL:
STATISTICS:
Input variable: DPO4034(CH1);
Check Box: number of samples.
FORMULA
Input variable 0: DPO4034(CH1); alias: x0
Input variable 1: "Total Time Window on Scope???"; alias: x1
Input variable 2: Number of Samples (CH1); alias: x2
Under Operation Setup: Formula
Y= (x0^2)*(x1/x2)
Output: Processed Data 1 (CH1)
THEN USING STATISTICS:
Input signal: Processed Data 1 (CH1)
Check Box: SUM
Output: CH1 Action Integral [A^2s]
Solved!
Go to Solution.Hi again Catherine,
I have now added another TekScope (TDS3032B) along with the DPO4034 and run the same work-around on the TDS3032B using CH1 as the "real" signal channel and CH2 as the "burst width" channel. However, the value returned for CH2 is nominally 99E+36 (min 99E+36, max 99E+36) with very few retrievals of correct burst width (~200ms). Seems the SignalExpress program is unable to consistently retrieve from TDS3032B the actual burst width (scope's time scale/window) and defaults to 99E+36 value. Any ideas on what is occurring and how to make it work? Attached are some screen captures to help guide discussion.
Regards,
Michael
Attachments:
TDS3032B - incorrect burst width.png 301 KB
TDS3032B - correct burst width.png 287 KB
DPO4034 - always correct burst width.png 302 KB -
Help in finding the total count for each month
Hello everyone,
Sometime back I had posted about the date function. I have that problem solved now my problem is that after finding all records which against each record I need to find the total count for that month if no records than I have to set it to a 0.
Here is how my program has been written.
PROCEDURE extract_materials
IS
CURSOR xyz
BEGIN
FOR xyz1 IN xyz LOOP
-- once inside the loop for each of the record from
the cursor I need to find a total count for that record for everymonth in the year.
All these records will be instered in to a staging table
Can you please help me out with this. I really appreciate this.
Thanks in advance.
-VaniAndrew - you missed the tricky bit of the spec - include missing months with a zero.
You need to do an outer join to a select from any big table with a function involving rownum and add_months to generate all the possible months. However, its time to go home and I can't be bothered to work out the finer details. -
How can I calculate the total time in java?
Hello!
I need to calculate the total time!
For example I have start time:
Format formatter1;
Date date1 = new Date();
formatter1 = new SimpleDateFormat("hh:mm:ss");
String startTime = formatter1.format(date1);
//startTime = "14:20:40";
And I have finish time:
Format formatter2;
Date date2 = new Date();
formatter2 = new SimpleDateFormat("hh:mm:ss");
String finishTime = formatter2.format(date2);
//finishTime = "08:30:55";
So, after manually calculating, I get total time: "18:10:15"
How can I calculate the total time in java? (Using formatter1 and formatter2 I suppose)
What I need is to print "total 18:10:15"
Thanks!800512 wrote:
I did the following but, I think something is wrong here:
I defined before: Date date1 = new Date(); Date date2 = new Date();
And it should be exactly 5 seconds between them.
I found delta between date1 and date2:
Format formatter = new SimpleDateFormat("HH:mm:ss");
long timeInMilliFromStart = date1.getTime() - date2.getTime() ;
Date date3 = new Date(timeInMilliFromStart);
String timeInSecFromStart = formatter.format(date3);
and I get always
//timeInSecFromStart = 02:00:05
But it should be exactly 00:00:05.
What can be a problem?Because, like I said, a Date measure an instant in time, not a duration. So when you have 5000 ms, and you turn that into a Date, that means 5 sec. after the epoch, which works out to 1/1/1970 00:00:05.000 GMT.
As I mentioned, if you're not currently in GMT, then you have to set the TZ of the DateFormat to GMT. Right now, it's showing you the time in your TZ. If you included the date in your SimpleDateFormat, you'd see either 1/1/1970 or 12/31/1969, depending on which TZ you're in.
Bottom line: You're trying to use these classes in a way they're not meant for, and while you can get the results you want for a limited set of inputs if you understand what these classes do and how to work with that, it's a brittle approach and comes with all kinds of caveats. -
How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro. What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
NOTE: If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did. He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse.
THIS IS WHAT YOU WILL NEED TO DO:
First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up. If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it. Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO. -
How can I get the elapse time for execution of a Query for a session
Hi ,
How can I get the elapse time for execution of a Query for a session?
Example - I have a report based on the procedure ,when the user execute that it takes say 3 min. to return rows.
Is there any possible way to capture this session info. for this particular execution of query along with it's execution elapse time?
Thanks in advance.Hi
You can use the dbms_utility.get_time tool (gives binary_integer type value).
1/ Initialize you time and date of beginning :
v_beginTime := dbms_utility.get_time ;
2/ Run you procedure...
3/ Get end-time with :
v_endTime := dbms_utility.get_time ;
4/ Thus, calculate elapsed time by difference :
v_elapsTime := v_endTime - v_beginTime ;
This will give you time elapsed in of 100th of seconds...
Then you can format you result to give correct print time.
Hope it will help you.
AL -
Can I use my creative cloud account at the same time for my iMac and my MacBook?
Can I use my creative cloud account at the same time for my iMac and my MacBook?
Thank you Sheena!!
Guy
Op 2-jan.-2015, om 12:16 heeft Sheena Kaul <[email protected]> het volgende geschreven:
Can I use my creative cloud account at the same time for my iMac and my MacBook?
created by Sheena Kaul <https://forums.adobe.com/people/Sheena+Kaul> in Adobe Creative Cloud - View the full discussion <https://forums.adobe.com/message/7059158#7059158>
Hi Guy Heyligen,
Absolutely. You can use the creative cloud account on two machines.
You may also refer to the link below:
Creative Cloud Help | Creative Cloud / Common Questions <http://helpx.adobe.com/creative-cloud/faq.html>
Regards,
Sheena
If the reply above answers your question, please take a moment to mark this answer as correct by visiting: https://forums.adobe.com/message/7059158#7059158 and clicking ‘Correct’ below the answer
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page:
Please note that the Adobe Forums do not accept email attachments. If you want to embed an image in your message please visit the thread in the forum and click the camera icon: https://forums.adobe.com/message/7059158#7059158
To unsubscribe from this thread, please visit the message page at , click "Following" at the top right, & "Stop Following"
Start a new discussion in Adobe Creative Cloud by email <mailto:[email protected].com> or at Adobe Community <https://forums.adobe.com/choose-container.jspa?contentType=1&containerType=14&container=46 70>
For more information about maintaining your forum email notifications please go to https://forums.adobe.com/thread/1516624 <https://forums.adobe.com/thread/1516624>. -
How can I get Messages to show the correct time for read receipts?
Messages in Mountain Lion shows the wrong time for read receipts. For example, my iPad will show a message was read at 3:37 pm but if I open Messages on my MacBook, the read receipt shows the time that I opened the Messages app as opposed to the time the message was actually read. This is not too much of an issue if my iPad is handy, but really, shouldn't Messages on my MacBook be able to show the correct time the message was read? It syncs all the other infromation with Messages on iOs.
I should mention that if Messages is running on my MacBook when the recipient reads the message, then it does show the correct time the message was read. It's if Messages was not running and I re-launch it that the read receipt time gets mixed up.HI,
As far as I am aware Messages marks or time stamps an iMessage at the time of receipt rather then the time you got around to reading it.
I will admit that in most cases reading and receiving as the app opens will be near enough the same time in some conversations.
Adding Time Stamps to Chat is what iChat has always done particularly with AIM based Chats.
The "Sync" in Messages is "display on all devices" and after that each iMessages is dealth with separately on each device.
There is no syncing of deleting/dimssing an iMessages or having read it on another device.
8:58 PM Tuesday; April 16, 2013
iMac 2.5Ghz 5i 2011 (Mountain Lion 10.8.3)
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb (Snow Leopard 10.6.8)
Mac OS X (10.6.8),
Couple of iPhones and an iPad
"Limit the Logs to the Bits above Binary Images." No, Seriously
Message was edited by: Ralph Johns (UK) -
I have a brand new Ipod touch with front facing camera. Not sure which generation it is. My wife connected the iPod Touch and chose the restore option when connecting to iTunes. It was a mistake and by the time I got there, I saw the screen with USB cable with an arrow facing towards iTunes logo. I cannot get the iPod out of this state.
Try here:
iPhone, iPad, or iPod touch: Device not recognized in iTunes for Windows
Also reset the iPod.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears. -
When my Ipod touch is in autolock I can only restart the device holding the sleep/wake button and home button at the same time for 10 seconds. While in auto-lock it is using battery power and will do so until the battery is drained. Whats wrong?
- Try a reset. Nothing is lost:
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears
- Connect the iPod to your computer and try to restore via iTunes. Try placing in Recovery mode if necessary to restore.
- If you can't turn the iPod completely off, let the batter fully drain. After charging for at lerast anhour try again
- If still not successful time for an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Maybe you are looking for
-
The problem about integrate Portal and R/3
Hi everyone : We want to achieve that our vendor can query R/3 report via our Portal. I had done SSO configuration. But we had about 500 vendors, it is impossible that we create 500 R/3 users for our vendors, because the cost is too much .
-
How do I print in black and white with HP Deskjet 5740?
I have just updated from Snow Leopard to Mountain Lion. With Snow Leopard, and an HP Deskjet 5740 printer, I could choose to print in draft or best quality, black and white only or in full colour, and had various other options. Now I am not offered t
-
Is there any way to copy songs from my Zen Touch over to my comput
I can't seem to find a way, but if there IS no way...
-
I do not like the interface of the new version. I lost a lot of playlists and songs in the iMatch process. As I attempt recovery from backups, I am trying to identify how many duplicates I have in total. I can get a list, but there are too many to
-
How to print data of selection screen
hi plz tell me how to print that data in smartforms which the user enters in the selection screen...........