Controlling MPLAB ICD-2 using Labview

All,
Need some real help here if possible?
I have to program a PIC 18F8680 using a MPLAB ICD-2 programmer controlled by Labview, does anybody have any experience in this (or something similar) who could shed some light on the subject of where to start?
Regards
AnotherNewbie

Hi AnotherNewbie,
Thank you for posting your question. My name is Kevin and I am an Application Engineer for NIUK. I will be helping you on this issue.
I have found a forum post where someone has asked a similar question "How can I control PIC programmer with LabVIEW" and there has been a discussion where some ideas have been passed around.
Please follow the link
Some of the ideas that are mentioned are controlling the software through DLL's through system exec calls from LabVIEW.
Here is a link for help with System Exec
Have a good look through the forum, there are some attachments provided in the thread that you may find useful.
This is definitely a good starting point.
Let me know how you get on
Kind Regards
Kevin R
Applications Engineer
National Instruments UK&Ireland

Similar Messages

Controlling a Servo Motor Using LabVIEW, Phidget & Mac OS

Can anyone help me with this problem?
I'm attempting to control a servo motor attached to a Phidget, using a VI in LabVIEW on a Mac. The Phidget works fine with the Mac, LabVIEW works fine with the Mac, but there seems to be a problem combining the three. The problem I'm encountering is that the examples on the Phidget website (www.phidgets.com) for LabVIEW use ActiveX. Can anyone suggest a solution for this? Is it possible to use one of the control options in LabVIEW (GPIB, VISA, etc etc.) instead?
I'm not great with computers so really have no idea where to start.
Thanks!

Thanks for your reply Jeff! So I can insert a CIN to the block diagram, right click and use the 'create .c file' option, insert the example code for controlling the motor from the Phidgets website (after tweaking it to make it specific to my setup) and that should work? How do I load the C library? Or a better question may be, what is the C library? (I wasn't joking when I said I'm totally new to this!)
I've been working my way through 'C for Dummies' this week but I have to admit, the bit about header files and libraries lost me. I downloaded a bunch of stuff from the Phidgets website, including the phidget21.h and phidget21.lib files...do I '#include' both of these at the top of the example code?
I've been in touch with the Phidget Support team (who are indeed great!) and received a similar reply ("You would have to call into the mac Phidget21 Framework directly").
Once the CIN is all set up do you know what degree of control I'll have over the motor? The aim is to have the motor move in steps from -60deg to +60deg around a central point. Would this need to be defined in the code and then linked into LabVIEW or is this something I could control from within LabVIEW? The idea of my project is to use the motor to move a light source around a sensor. The sensor is hooked up to an NI DAQ that will record and display values (after some manipulation) on the front panel. I hope to display the sensor values and the corresponding motor position values.

HT5672 Where i can find Java for Mac OS X 10.8.3 ??? i need to use MicroChip debugger MPLAB ICD 3

I need to install MPLAB X IDE v1.70 for Microchip Debbuger MPLAB ICD 3. I download it from Microchip web-site and try to rub but it is asking to Java to proceed with installation. I try to find it of apple.com but nothing only for previous OS.
Thanks for your help in advance!

woodmeister50 wrote:
…in terminal I get this:
XXXXXXXXXX$ java -version
java version "1.6.0_37"
Java(TM) SE Runtime Environment (build 1.6.0_37-b06-434-11M3909)
Java HotSpot(TM) 64-Bit Server VM (build 20.12-b01-434, mixed mode)
Not sure what is going on here….
What's going on is that the Terminal command tells you which Java 1.6 you have. That one's obsolete, since the latest is:
$ java -version
java version "1.6.0_43"
Java(TM) SE Runtime Environment (build 1.6.0_43-b01-447-10M4203)
Java HotSpot(TM) 64-Bit Server VM (build 20.14-b01-447, mixed mode)
To determine your Java 1.7 version via the Terminal, you need to run:
$ /Library/Internet\ Plug-Ins/JavaAppletPlugin.plugin/Contents/Home/bin/java -version
java version "1.7.0_17"
Java(TM) SE Runtime Environment (build 1.7.0_17-b02)
Java HotSpot(TM) 64-Bit Server VM (build 23.7-b01, mixed mode)

Controlling two cameras using LabVIEW

Hi,
I am a research assistant and my task is to control two cameras using LabVIEW. Also I need to store the pics automatically in a file having the exact time for each pic when taken. I am still new to this kind of work but I am trying my best to learn. I am using some icon for saving pictures but they were stored as RSC format. You can take a look at what I've done so far. I really appreciate if someone can help me with that. Thank you
Regards,
Abbas
Attachments:
Controling two camera.vi ‏85 KB

Hi try this VI... I have made very little modification in that... What type of camera you are using.. what is the interface?....
The best solution is the one you find it by yourself
Attachments:
Controling two camera.vi ‏84 KB

How to let the user define the colors for each plots in the graph (I use LabVIEW 7)?

How to let the user define the colors for each plots in the graph (I
use LabVIEW 7)?

Hi,
Take a look at this example, it uses property nodes to select tha
active plot and then changes the color of that plot.
If you want to make the number of plots dynamic you could use a for
loop and an array of color boxes.
I hope this helps.
Regards,
Juan Carlos
N.I.
Attachments:
Changing_plot_color.vi ‏38 KB

Sending email using labview 8.6

I am trying to send an email using labview 8.6.But I am getting error 1172 when I try to do so.
Kindly let me know what modificatons i should do to the port an d server settings.
I have taken the code from forum only
I am posting a renamed version of it.
gmail-1 is its actual name in forum
kindly suggest me what I should do
thanks
Attachments:
gmail_labview.vi ‏16 KB

Dear sir,
I have done as you said and observed that the error is coming at the final node "smtp client-send-message"
I did not installed any .NET or any other programs.
A screen shot of the error along with the error node is attached for your reference.
thanks
Attachments:
gmail_labview_error.JPG ‏73 KB

I am trying to use Labview and RP1210 compliant hardware to connect to a truck J1939 bus and receive messages.

I am trying to use Labview and RP1210 compliant hardware to connect to a truck J1939 bus and receive messages.
Specifically I am attempting to read data frames using the RP1210_READMESSAGE . am able to configure the hardware and send a message to the J1939 bus. . I think I have not configured something correctly. I can use the RP1210_SENDMESSAGE and see the message I have sent on the bus using CANalyzer When I use the RP1210_READMESSAGE I get the timestamp from a message and the return from the function sends back the correct number of bytes (the number matches the number of bytes I sent out plus four bytes from the timestamp). What I am having trouble with is actually receiving the data. I have had the same type of behavior from two different hardware (Vector CANcase XL and Nexiq USB Link), so I don't think the issue is vendor specific.
Has anyone been able to make the RP1210_RECIEVEMESSAGE function work correctly?
Thanks for any help

Thanks
I have already tried that. The links are the NI RP1210 wraper. The problem I am having is using labview to interface with the RP1210 layer. The RecieveMessage char*fpchAPIMessage this is the output which is a pointer to a cahracter array. In this variable I can receive the timestamp of the message but not the message. The retun showns the correct amount of bytes are aviaable (18 for a 8 byte message) but I can only get the 4 byte timestamp I think I have to dereference this pointer to view the data. I am not sure how to fix this.

I am trying to integrate simulink model (.mdl) file with SIT of Labview for RCP and HIL purpose. I am using Labview 8.6, Simulink 6.6 with RTW 6.6 and RTW embedded coder 4.6 ,Visual C Express 2008 and Visual C++ Express 2008.

I am trying to integrate simulink model (.mdl) file with SIT of Labview for RCP and HIL purpose. I am using Labview 8.6, Simulink 6.6 with RTW 6.6 and RTW embedded coder 4.6 ,Visual C Express 2008 and Visual C++ Express 2008. I have selected system target file as nidll.tlc,make command as make_rtw and template nidll_vs.tmf. When I try to generate .dll file I get the following error.
Attachments:
SITProblem.JPG ‏101 KB

Hi,
No . I could not solve the issue. Presently we are using microautobox (from Dspace)for doing the RCP.
Himadri

How do i open and control other programs using labview?

I'm presently trying to use labview to try to open and operate another program,but having much difficulty.The external program i'm using is called the Foundation program.
This Foundation program will use VHDL programming to create a virtual chip and then synthesising it.This program will then simulate the output of this VHDL program to verify that it is working as desired.Then the last stage is to download the whole VHDL program into a FPGA chip using a xilinx cable.
All this need to be done using a labview program - to open the Foundation program and then extract the saved file and then to execute the download command to cause the VHDL program to be downloaded onto the FPGA chip.How do i go
about doing all this?What is the first step i must do.Also all this have to be done thru networking..looks like its too difficult..I really need help.
grays

I haven't done VHDL so pardon my ignorance.
LabVIEW can call external DLL via "Call Library Function" or C programs via "Code Interface Node", both located in "Advanced" function.
If your program is a DOS program, use "System Exec.vi" found in "Communication" function. If you need to format your DOS command prior to sending it, use the "Format Into String" function in "String" function palette.
Lastly, if you're trying to extract data, assuming it is text, use "File I/O" functions. If the data is binary, use "File I/O -> Binary File VIs".
Hope that answers most of your questions.
Shan Pin Koh

I use labview 8.0 and i can not run daqmx driver for pcmcia 6062e daq card

i use labview 8.0 on window xp .when i installed a PCMCIA daq card 6062E, i could not run daqmx driver.It is fine to see that the traditional version is working well.When i install daq card sometimes it is working well with traditional driver but mostly i see error on reading an analog input from PCMCIA daq device.An error called 'base adress' occures .I use last version of driver that is daqmx 8.0.1. and i have installed this correctly but again i could not see any signal on the test panel for daq-mx driver.I don't know what is the problem.Also when i install PCMCIA daq card Please reply this message.I need your helps.
Thanks

Hello,
Thanks for your reply.I will try to answer your questions.
I have checked the Device Mananger and I have seen that the device is detected by Windows XP. For another question the card shows up under both NI-DAQmx Devices and Traditional NI-DAQ (Legacy) Devices consistently in the Measurement & Automation Explorer.I use a way that I reset the driver for traditional NI-DAQ in MAX,and then i reset the device for NI-DAQmx driver in MAX and again i tried to run the test panel of DAQmx driver but again i saw a wrong signal or noise signal on the test panel i could not see the sinusoidal signal that i connected. i do get the test panels to run with the card using the DAQmx driver, But could not run the DAQ diagnostic utility.The error was as i specified below.
03.05.2006 09:49:35
Results saved to: C:\Documents and Settings\serkan\Desktop\Diagnostic Results.txt
Selected Device: Dev1
Device Type: DAQCard-6062E
Serial Number: 107509E
Device Support: (PASS)
NI-DAQmx Version: 8.0 (PASS)
Device Reset: (FAIL)
Error -50002 occurred at an unidentified location
Possible reason(s):
The specified device is not a valid device. The operation could not be completed as specified.
------ DIAGNOSTIC UTILITY ABORTED -----
And for your last question i can say that i have used the DAQ card on other laptops.But the results were the same.İ hope to see your reply
Thanks,
Serkan Buhan
Electrical-Elecronics Engineer
Researcher
TUBITAK-BILTEN

How to use labview to control a robotic arm by EMG signal

Hello,
I am working on simulation of an active Exoskeleton (wearable robot) for the upper limb using LabVIEW for my senior project. I need to use the EMG signal as an input to move the elbow joint (flexing and extending). I downloaded labview biomedical toolkit to take a ready simulated EMG signal but have a weak experience in LabVIEW.
The design criterial I am planning to use is to establish a threshold for the EMG signal using a comparator (above 0 for example) and set a counter for everytime the signal passes the threshold as(+1) in every count. Then, specify a degree value for the counter (for example when the counter reaches 10000) and feed this value of the counter to a simple simulated structure for the joint (simple angle of 2 lines) or a meter to represent the movement.. e.g. every 10000 count = 1 degree of movement. Zero crossing can also be used instead of the comparator and the signal will be filtered and that is easy to do. However, my problem is in converting this logic into LabVIEW. I don’t know how to set a counter for the signal and make every number of counts refer to a specific degree of movement and I also don’t know how to form the simulated joint structure in LabVIEW or even how to transfer this into a simple meter device in LabVIEW.
I have only one month to do this project so any help or ideas you provide are highly appreciated
Thank you ,

CarlFHellwig
Thank you for providing this example I just implement it in the software to check the counter results.
In fact, the design criteria I desided to use latly is to use is to establish a threshold for the EMG signal using a comparator and correlate the EMG signal with the angles of movement of a simple simulated structure "motor" for a single joint (simple angle of 2 lines) eg. 30,60,90,120,150 degrees for flexing and extending. Zero crossing can also be used instead of the comparator and the signal will be filtered and that is easy to do.
In other words, the idea is to drive a motor for different angles based on the input EMG signals. I am now stuck with developing the algorithm of how the angles are related to the RMS value of the signal while flexing and extending and how to convert this RMS into angular velocity and angular position to form the simulation.
I will be grateful if someone guided me to a person did a similar project to discuss some issues.

How do I use LabVIEW to control and vary the voltage on my Agilent Power Supply and simultaneously record temp from 1 DMM and voltage from another DMM?

I am using an Agilent Power Supply to apply a voltage to a
thermistor to heat an Al chassis. I want to use LabVIEW to tell
the power supply to apply 5V for 10 minutes, then step to 7V for 10
minutes, etc. I am completely new to LabVIEW, so any help would be greatly appreciated!
In addition to that, I want to place a type J thermocouple onto the Al
surface and use a Keithley 2000 DMM to monitor the temperature (it has
a built in conversion from V to Temp for type J). I will also be
using another Kelthley 2000 DMM to record the output voltage of a new
uncalibrated thermocouple. I would like to collect the output
voltage for this uncalibrated thermocouple and the temperature reading
from the type J simultaneously. How should I go about doing this
in LabVIEW? I will be using version 6.1. The power supply
and DMMs will be connected to a PC using GPIB.
Again any suggestions would be greatly appreciated- I have no idea
where to begin on such a project. I have taught myself how to
make a basic VI- converting temp in oC to oF, but that is as far
as my knowledge goes.

What you want to do should be fairly straightward and a good way to learn labview.
First off, if you haven't already, I would download the drivers for the Keithley and Agilent instruments. I found the keithley drivers at the link below. You will need to find the labview drivers for the Agilent PS at their website. Drivers are the VI's you will use in your program to control the insturments.
http://sine.ni.com/apps/we/niid_web_display.download_page?p_id_guid=E3B19B3E90B0659CE034080020E74861
If you open Labview and go to the help menu and click on Labview bookshelf there is alot of information on getting you started coding labview. This should get you started, if you have anymore questions just ask in this same thread and I am sure you will get all the help you need.
Brian
Message Edited by BrianPack on 09-14-2005 05:21 PM
Message Edited by BrianPack on 09-14-2005 05:21 PM

How do I turn off background ni file activity when not using Labview? files such as nimxs.exe, nipalsm.exe, nipalsm.exe, nisvcloc.exe, nicitdl5.exe

How do I turn off background ni file activity when not using Labview? I use labview rarely, and I also use my computer for demanding multimedia applications, including multitrack digital audio recording. I need to reduce as much background activity as possible, and taking a look with task manager I see files such as nimxs.exe, nipalsm.exe, nipalsm.exe, nisvcloc.exe, and nicitdl5.exe running even when I haven't used Labview (8 I believe). These files run even after I right click the NI icon on the lower right and turn off the application. I would like the computer to boot up without these files, and for the necessary files to be activated only when I start the program.
Can this be done or do I have to remove labview from the system to improve performance?
Thanks

Hello, those processes are part of running NI services that start when Windows boots. These processes serve varied purposes and stopping them can have undefined and unknown consiquences for your NI products. These products run at "normal" priority meaning that they should be preempted by any process running at a higher priority which I would expect your other application to be doing given their time sensitivity. That being said, in Windows XP (I can't speak for other OSes), you can lower their priorities even greater through task manager (right click the process»set priority) to further remove them from contention for resources. If you want to prevent them from running you can set the service startup type to "manual" in Control Panel»Administrative Tools»Services. Right click the process go to Properties and Under the General tab choose Startup Type»Manual. This will start up the processes only when something directly starts it up. LabVIEW will start these processes up as it attempts to use them. When you shut down LabVIEW you will need to manually shut down these processes through task manager. Again, doing this can cause problems with your NI products on your system and it is not advised.
Travis M
LabVIEW R&D
National Instruments

How do I browse & play .mp3 files from a USB flash drive using Labview 8.0?

I'm a tester & want to test USB flash drives connected to PC.
I want to browse the file system & playback the audio files, .jpeg files etc in the USB drive. I've Labview 8.0. When I searched for some examples or VIs which can detect the USB flash drive, couldn't find any. So if you could point me in the right direction, I can find a solution to my problem.
Thanks.
Solved!
Go to Solution.

You probably won't find specific examples for this. A USB flash drive is mounted by the OS and appears as a new memory storage device to all software on the PC, including LabVIEW. You can certainly write a LabVIEW program to open files on the stick and play/run them but I would create a VI that wrote files to the stick and then read them back and checked them for bit-level errors. Keep in mind that your OS might be doing parity checking under the hood which would make your test rather meaningless.
BTW, testing memory by looking at pics or listening to MP3s would be useless of course. A human can't see or hear bit-level errors in a high bandwidth data stream.
Using LabVIEW: 7.1.1, 8.5.1 & 2013

How can i design a smart antenna using labview?? plzz

i have my final year project. I am student of Beng in Telecommunications. How can i design a smart antenna using switched beam algorithm on lab view??

You can hardly use LabVIEW to design antenna, but definitely can use LabVIEW for Characterization, Optimization, and Test your antenna design.
Hope you got the point here.
I am not allergic to Kudos, in fact I love Kudos.
Make your LabVIEW experience more CONVENIENT.

Controllin​g MPLAB ICD-2 using Labview

Similar Messages

Maybe you are looking for

Controlling MPLAB ICD-2 using Labview