Couldnot Export Netflow entries in the PFC (hardware switched)
Hi,
On the Netflow Collector we are not able to see hardware switched flow entries in PFC, but software switched flow entries in MSFC can be seen. One thing which I have observed in the "show ip cache flow" output I see PFC as standby although the flow entries are there. We did the packet capture on the netflow collector but could not find hardware switched flow entries, so it seems that 6506 is not sending PFC entries.
Following is the configuration.
mls aging long 64
mls aging normal 32
mls netflow interface
mls flow ip interface-full
no mls flow ipv6
mls nde sender version 5
mls cef error action reset
ip flow-cache entries 128000
ip flow-cache timeout active 1
ip flow ingress layer2-switched vlan 10,20
ip flow-export source Loopback0
ip flow-export version 5
ip flow-export destination 10.19.20.31 9996
show ip cache flow
Displaying software-switched flow entries on the MSFC in Module 5:
IP packet size distribution (8679322 total packets):
1-32 64 96 128 160 192 224 256 288 320 352 384 416 448 480
.132 .142 .325 .166 .082 .046 .019 .015 .006 .000 .001 .000 .001 .000 .013
512 544 576 1024 1536 2048 2560 3072 3584 4096 4608
.001 .001 .001 .005 .035 .000 .000 .000 .000 .000 .000
IP Flow Switching Cache, 8454644 bytes
30 active, 127970 inactive, 1523126 added
438002488 ager polls, 0 flow alloc failures
Active flows timeout in 1 minutes
Inactive flows timeout in 15 seconds
IP Sub Flow Cache, 1040712 bytes
30 active, 31970 inactive, 1522942 added, 1522942 added to flow
0 alloc failures, 0 force free
1 chunk, 1 chunk added
last clearing of statistics 2w1d
Protocol Total Flows Packets Bytes Packets Active(Sec) Idle(Sec)
-------- Flows /Sec /Flow /Pkt /Sec /Flow /Flow
TCP-FTP 40819 0.0 10 73 0.3 0.5 3.1
TCP-FTPD 40607 0.0 3 42 0.1 0.0 1.5
TCP-WWW 2071 0.0 10 918 0.0 5.1 164.8
TCP-other 39829 0.0 25 245 0.7 6.6 188.0
UDP-DNS 1579 0.0 3 92 0.0 6.7 293.7
UDP-NTP 3309 0.0 2 94 0.0 105.4 195.0
UDP-TFTP 2 0.0 10 52 0.0 169.3 131.2
UDP-Frag 5 0.0 1 57 0.0 1.0 299.5
UDP-other 576228 0.4 2 197 1.1 13.8 285.8
ICMP 55727 0.0 4 591 0.1 161.5 137.9
GRE 28899 0.0 45 28 0.9 285.4 1.0
IP-other 111838 0.0 34 129 2.9 292.4 8.0
Total: 900913 0.6 9 150 6.5 65.0 202.5
SrcIf SrcIPaddress DstIf DstIPaddress Pr SrcP DstP Pkts
Gi5/2 172.16.148.254 Tu2 10.191.32.12 2F 0000 0000 2
Gi5/2 172.16.195.254 Tu4 10.191.32.14 2F 0000 0000 2
Gi5/2 10.191.32.62 Vl10 10.191.32.12 2F 0000 0000 4
Displaying hardware-switched flow entries in the PFC (Standby) Module 5:
SrcIf SrcIPaddress DstIf DstIPaddress Pr SrcP DstP Pkts
Tu5 10.191.8.89 Vl10 10.190.102.240 2F 0000 0000 4780
Tu5 10.191.8.89 Vl10 10.190.103.89 2F 0000 0000 6218
Gi5/2 10.122.3.35 Tu4 172.16.33.97 06 008B 105F 1
Tu5 10.191.8.89 Vl10 10.190.102.123 2F 0000 0000 73
Tu5 10.124.24.45 Tu2 172.16.148.17 06 0E9F 008B 2
Tu5 10.124.114.221 Gi5/2 10.129.1.89 06 4E21 04D8 450
Gi5/2 10.70.72.8 Tu6 172.16.105.242 06 0050 0B3E 5
show module
Mod Ports Card Type Model
5 9 Supervisor Engine 32 8GE (Active) WS-SUP32-GE-3B
6 9 Supervisor Engine 32 8GE (Hot) WS-SUP32-GE-3B
Mod MAC addresses Hw Fw Sw Status
5 001f.6cfe.aba2 to 001f.6cfe.abad 4.6 12.2(18r)SX2 12.2(33)SXH3 Ok
6 001f.9e9a.ae4c to 001f.9e9a.ae57 4.6 12.2(18r)SX2 12.2(33)SXH3 Ok
Mod Sub-Module Model Serial Hw Status
5 Policy Feature Card 3 WS-F6K-PFC3B 2.4 Ok
5 Cat6k MSFC 2A daughterboard WS-F6K-MSFC2A 4.0 Ok
6 Policy Feature Card 3 WS-F6K-PFC3B 2.4 Ok
6 Cat6k MSFC 2A daughterboard WS-F6K-MSFC2A 4.0 Ok
I have gone through following documents but could not find any clue on why PFC entries are not exported.
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SX/configuration/guide/netflow.html#wp1080827
http://www.cisco.com/en/US/products/hw/switches/ps708/products_configuration_example09186a0080721701.shtml
Regards,
Akhtar
Hi,
Just to further update this case with troubleshooting results.
1. I am able to recieve all flows sent from NDE 6506 Switch on NF Collector-A.
2. Only few flow are being received on NF CollectorB.
3. When comparing packet captured on NF Collector-A and B, I see only small size UDP packets(~350bytes) on NF Collector B, whereas on NF A I see packets more than 800 bytes...
This issue is surely pertaining to GRE+IPSEC. I have checked the forums and found issue of ""Self Generated Netflow packets not encrypted"" but my issue not seems to relevant b/c NDE 6506 which is exporting Netflow is not encrypting.......
Any thoughts !!
NDE 6506 Switch)----(CORE-6509)----(DC-WAN-1-6506)-----GRE+IPSEC------(DC-WAN-2-6506)------(CORE-6509)-----(DC-AGG)----(DC-ACC)---NF CollectorB
|
|
NF Collector-A
Similar Messages
-
Get the error "Make an entry" in the date field
Hallo Experts,
I have the following problem. I have a date filed with value help. In the Getter-Method, I inserted the following code to get a value help:
CALL METHOD CL_CRM_UIU_BT_DATE_TOOLS=>GET_DATE
EXPORTING
IV_ATTRIBUTE_PATH = ATTRIBUTE_PATH
IR_BTDATE = current
IR_MODEL_UTIL = me
RECEIVING
RV_VALUE = value
EXCEPTIONS
CONVERSION_ERROR = 1
* others = 2
so far is everything is ok, I can select my date in the field. But the problem is, if I select an other button without any funktion (no event) in the same viewset I get the error message: Make an entry in field "Date". By the way, the field date is a mandantoy field.
My intention is, that the entry of the date filed is still exist (without to save) if I push an other button to invoke an event.
Could anyone help me?
Best regards,
JohnHi,
You are only displaying the date in getter method. To set the date in the entity it should be done using set_property.
current->set_property( iv_attr_name = 'date field' iv_value = 'value' ).
Check whether the date is set in setter method. If not add the above code.
Regards,
Arun -
This is file I created in SnapzPro (which was saved as a Quicktime mov - Animation) of a Powerpoint Presentation.
Jon, how do I re-compress the Snapz data for dvd playback?
That depends on your specific work flow strategy. I normally perform the processing in two stages if editing is involved or in a single stage if I don't plan to trim, title, add a narration track, add special effects, and/or add filters to the Snapz Pro X captured screen data.
In the two-stage process you export the captured data to an intermediate low-compression, high-quality fomat. (This can be the default settings for Snaps Pro X or a more modern editing specific format like ProRes 422/Linear PCM depending on the codec components for which your system is configured and your personal editing preferences.) The Snapz Pro X intermediate file is then edited in the application of your choice and the results are re-compressed to your final target compression format.
In any case, whether you are re-compressing the data using QT 7 Pro, iMovie, GarageBand, MPEG Streamclip, Snapz Pro X, or similar third-party app that accesses the built-in OS X QT routines, the export process is essentially the same. Whether you use a "Movie to MPEG-4" or "Movie to QT Movie" export, you must export to a data rate limited, multi-pass H.264/AAC compression combination to take advantage of the "Optimize of CD/DVD" option. Specific data rate limits depend on the playback dimensions of the file you are creating, the minimum level of quality you will accept, and the playback speed of the hardware to be used. (I normally target 4X-8X settings for SD content but if you know the recipient has a higher rated optical drive and your content is HD, then you can use higher encode settings for improved quality.)
I captured the slideshow again in Snapz, and saved it as H264/AAC. Is this good enough?
If you did not specifically use the "Optimize for..." feature, then the file is automatically targeted for "Computer" playback which assumes playback is from an hard drive which has greater bandwidth/faster throughput than an optical media player. If the target display dimensions are resonably small, the the contextual nature of the H.264 video encoder may or may not be within the playback limitations of an optical drive usually depending on the encode matrix dimensions, graphic complexity of the source data, overall brightness of the scenes, and limitations you may have place on the target file—i.e., the larger the encoding dimensions, the faster the data date and the less likely the file will be compatible with optical drive playback without having to constantly interrupt playback to cache/rebuffer additional data. However, you can always tell the recipient that if this happens, he or she should simply copy the movie file from the CD/DVD to their hard drive for playback.
What now? Do I open it in Quicktime and use the "share for mac and pc", then right-click on it in the finder and "burn to disc?"
What you do next depends on how you plan to burn the file. The steps explained above allows you to create a file that is compatible with playback from an optical drive in a QT Player app but is not authored for playback from a commercial DVD Player. Your next step is to burn that file to an optical disc that can be read by your recipient's computer. I my case, I normally burn the disc using a hybrid (HFS Plus/ISO 9660) format which supports HFS Plus, ISO-9660, Rock Ridge, and Joliet with Rock Ridge file systems. How you do this is up to you. You can, for instance, use a third-party app like Toast or Dragon Burn to create a data disc; create/burn an image file with your Disk Utility app (this is a good option if you plan to burn several discs now and/or in the future); create a named "Burn" folder, drop the file to it, and press the burn button; or simply insert a blank optical media disc into you optical drive, change the default disc name to whatever you want, drop your file to the blank media's Finder window, and press the "Burn" button. (NOTE: Burn options may differ depending on the software installed on your system and/or the version of OS X under which you may be operating.)
Dont see any specs re playback from an optical disc drive? The slideshow is only 3 min long, and I want to avoid turning it into a video DVD using iDVD, iMovie etc, as the quality of the pictures and type degrades badly. Thanks for the help. Been struggling with this for weeks.
As noted above, this is an encode setting that only becomes active when you are targeting your H.264/AAC encode for multi-pass/data rate limited compression. When active, the "Optimize for..." pop-up allows you to select "computer" (targets playback from a hard drive), "CD/DVD" (targets playback from optical media), or "Streaming" (targets playback from a realtime streaming server) options. This option prevents data rate excursions from exceeding limits normally associated with each of the named types of playback. This option has nothing to do with the file system used to burn the media disc which determines which platforms/OS can read the disc and the file it contains. -
For all entries changes the order of the itab
Hi Experts
In the following query i have used two internal tables namely it_first and it_zlist.
The material inwhich the it_zlist is different sorting order
After executing this query, the order of the material inwhich the it_first is different from the it_zlist.
What could be the reason, pls explain me on this.
select matnr test zsno ztnam from zmaster1
into corresponding fields of table it_first
for all entries in it_zlist
where matnr = it_zlist-matnr.
Thanks in advance.
Regards
Rajaramfor all entries u should specified all primary key.
sort by u condition.
Effect
If the addition FOR ALL ENTRIES is specified before the language element WHERE, then the components comp of the internal table itab can be used as operands when comparing with relational operators.
The internal table itab must have a structured line type and the component comp must be compatible with the column col.
The logical expression sql_cond of the WHERE condition can comprise various logical expressions by using AND and OR. However, if FOR ALL ENTRIES is specified, there must be at least one Comparison with a column of the internal table itab, which can be specified either statistically or dynamically (Release 6.40 and higher). In a statement with a SELECTstatement with FOR ALL ENTRIES, the addition ORDER BY can only be used with the addition PRIMARY KEY.
The whole logical expression sql_cond is evaluated for each individual line of the internal table itab. The resulting set of the SELECT statement is the union of the resulting sets from the individual evaluations. Duplicate lines are automatically removed from the resulting set. If the internal table itab is empty, the whole WHERE statement is ignored and all lines in the database are put in the resulting set.
Notes
In Release 6.10 and higher, the same internal table can be specified after FOR ALL ENTRIES and after INTO.
The addition FOR ALL ENTRIES is only possible before WHERE conditions of the SELECT statement.
If the additions PACKAGE SIZE or UP TO n ROWS are specified together with FOR ALL ENTRIES, they are not passed to the database system but are applied instead to the resulting set once all selected rows on the application server have been imported.
With duplicated rows in the resulting set, the addition FOR ALL ENTRIES has the same effect as if addition DISTINCT were specified in the definition of the selection quantity. Unlike DISTINCT, the rows are not deleted from the database system but are deleted on the application server from the resulting set.
Addition FOR ALL ENTRIES is only possible for WHERE conditions of the SELECT statement.
Example
Exporting all flight data for a specified departure city. The relevant airlines and flight numbers are first put in an internal table entry_tab, which is evaluated in the WHERE condition of the subsquent SELECT statement. -
PDF Exception: Invalid object for the XFA entry in the forms dictionary
Hi,
We have an online adobe interactive form, via webdynpro, which saves OK, but occassionaly when a form is loaded again the form appears blank and the below error is returned by the ADS. I've searched but cannot find any definitive answer to this issue:
Processing exception during a "GetData" operation.#Request start time:Tue Jan 11 14:08:47 GMT 2011#com.adobe.ProcessingException: Error exporting Data into PDF - PDF Exception: Invalid object for the XFA entry in the forms dictionary.#[Ljava.lang.StackTraceElement;@51bb49da##Exception Stack Trace:#com.adobe.ProcessingException: Error exporting Data into PDF - PDF Exception: Invalid object for the XFA entry in the forms dictionary.#[Ljava.lang.StackTraceElement;@51bb49da###at com.adobe.ads.remote.EJB_PDFAgent.exportFormData(Unknown Source)###at com.adobe.ads.operation.GetData.execute(Unknown Source)###at com.adobe.ads.operation.ADSOperation.doWork(Unknown Source)###atcom.adobe.ads.request.Request.processOperations(Unknown Source)###at com.adobe.ads.request.Request.process(Unknown Source)###at com.adobe.AdobeDocumentServicesEJB.processRequest(Unknown Source)###at com.adobe.AdobeDocumentServicesEJB.rpData(Unknown Source)###at com.adobe.AdobeDocumentServicesLocalLocalObjectImpl0_0.rpData(AdobeDocumentServicesLocalLocalObjectImpl0_0.java:120)###at sun.reflect.GeneratedMethodAccessor1814.invoke(Unknown Source)###at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)###at java.lang.reflect.Method.invoke(Method.java:324)###at com.sap.engine.services.webservices.runtime.EJBImplementationContainer.invokeMethod(EJBImplementationContainer.java:126)###at com.sap.engine.services.webservices.runtime.RuntimeProcessor.process(RuntimeProcessor.java:157)###at com.sap.engine.services.webservices.runtime.RuntimeProcessor.process(RuntimeProcessor.java:79)###at com.sap.engine.services.webservices.runtime.servlet.ServletDispatcherImpl.doPost(ServletDispatcherImpl.java:92)###atSoapServlet.doPost(SoapServlet.java:51)##at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)###at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)###at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.runServlet(HttpHandlerImpl.java:401)###at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.handleRequest(HttpHandlerImpl.java:266)###at com.sap.engine.services.http
server.server.RequestAnalizer.startServlet(RequestAnalizer.java:386)###atcom.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnali er.java:364)###at com.sap.engine.services.httpserver.server.RequestAnalizer.invokeWebContainer(RequestAnalizer.java:1039)###atcom.sap.engine.services.httpserver.server.Reques
Analizer.handle(RequestAnalizer.java:265)###at com.sap.engine.services.httpserver.server.Client.handle(Client.java:95)###at com.sap.engine.services.httpserver.server.Processor.request(Processor.java:175)###at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:33)###at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)###at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)###at java.security.AccessController.doPrivileged(Native Method)###at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:104)###at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:176)##Caused by: com.adobe.internal.pdftoolkit.core.exceptions.PDFInvalidDocumentException: Invalid object for the XFA entry in the forms dictionary.###at com.adobe.internal.pdftoolkit.services.xfa.impl.PDFFormSupport.exportXFAData(Unknown Source)###at com.adobe.internal.pdftoolkit.services.xfa.XFAService.exportDataset(Unknown Source)###... 32 more##
Please help!
Edited by: Kevin Alcock on Jan 11, 2011 2:20 PMHi Otto,
We have had the form working and in most instances the form can be updated multiple times without issue. However, occassionally a form is created OK but the next time it is launched it is blank (the data is visible when the PDF is downloaded to the desktop)
Do you think this issue could be to do with the form layout/XML...I changed the form template 2 days ago as I suspected this issue could be realted to incorrect field bindings but we have had the error on a form created after the change was made.
Many Thanks,
Kevin
Edited by: Kevin Alcock on Jan 13, 2011 1:10 PM -
Error message 'No entry in the table T589A for P 2'
Hi all,
I am updating the field of an infotype using the function module 'HR_INFOTYPE_OPERATION'. But the function module is not updating the field. Instead the return key of the function module has the message
'No entry in the table T589A for P2'. The function module is called as follows:
CALL FUNCTION 'HR_INFOTYPE_OPERATION'
EXPORTING
infty = '9900'
number = wf_pernr
SUBTYPE = P9900-SUBTY
OBJECTID =
LOCKINDICATOR =
VALIDITYEND = P9900-ENDDA
VALIDITYBEGIN = P9900-BEGDA
RECORDNUMBER =
record = p9900
operation = 'MOD'
TCLAS = 'A'
DIALOG_MODE = '0'
NOCOMMIT =
VIEW_IDENTIFIER =
SECONDARY_RECORD =
IMPORTING
RETURN = wf_return
KEY = wf_key
Please suggest.
regrds,
madhuHi,
The table T589A is a configuration table pertaining to the pf status of the infotype. I changed the pf status of the infotype i.e. added my own buttons on application tool bar. May be cos of that it is giving error. Not sure....... -
When I updated by iphone with IOS7, my calendar entries did not follow the icloud. I am only showing pre set calendar entries for the year and lost all other calendar entrie and it will not take any new entries. They show up in my outlook, but not on my iphone, which they did before I updated my software to the new i0s7
Before syncing, select each calendar on your Mac and back it up by going to File>Export>Export. If anything goes missing, you can use these to restore your calendars.
Have you tried simply force closing the calendar app on your iPhone? To do this, double-tap the home button, locate the calendar app, then swipe up on the image above the app icloud to close it and tap the home bottom. Then test your calendar again. -
Additional G/L account entry at the time of PGI.
Dear All,
I have scenario of exports. At the tiem of PGI we generally get the entries Inventory account credtt to cost of goods sold account credit.
I want to have a track the value of goods which are at the port. So it is required have another g/l account entry at the time of PGI.
Which will be recoicilled at the time of commercial billing.
Can any one help me out. How to have the addtional G/L account entries along with the standard G/L entry.
Thanks and regards
Rasik WaghelaHi Rasik
You need to modify the account assignment for Goods issue and find out a user exit to replace the account at the time to commercial biiling.
Regards
Yatin -
MAC address and the CAM entries on the Layer 3 FWSM(Transparent mode)
Hi,
With refrence of Cisco Secure Firewall Services Module (FWSM) of Cisco Press book it's mentioned that
"While configuring the transparent mode in FWSM, it is important to specify the MAC address and the CAM entries on the Layer 3 next hop device of FWSM."
This part of configuration is not very much clear to me please let me know the logic of this things
The following are two examples:
Layer 3 Device A (PFC) at the Outside Security Domain
! IP address of the next hop for the outside security domain
interface Vlan20
mac-address 0000.0000.0001
ip address 10.10.1.1 255.255.255.0
! Specify the IP address and MAC address at the first hop layer 3 interface
! of the inside security domain
arp 10.10.1.21 0000.0000.0001 ARPA
Layer 3 Device B at the Inside Security Domain
! IP address of the next hop for the inside security domain
interface Vlan21
mac-address 0000.0000.0021
ip address 10.10.1.21 255.255.255.0
! Specify the IP address and MAC address defined at the first hop interface
! of the outside security domain
arp 10.10.1.21 0000.0000.0002 ARPA
Regards
ChrisCheck the serial # reported by Sys Info against the serial # printed on the bottom of the case. I bet they are not the same. The service center did not change the serial # on that new Logic board to match the REAL serial number of your Mac.
So when you try to go to the MAS it looks like a completely different Mac which is not registered under your Apple ID.
If the above is true, the serials being different, then you need to take it back and have that changed to your REAL serial number. -
I did not deactivate a photoshop cs6 before there was a new "C" hard drive installed on my computer and a Win7 Pro fresh install too. How can I activate photoshop on the new hardware if I can't deactivate it on the old hardware that is no longer available? Any help will be appreciated.
If it's the same machine (same CPU) there should not be any need to activate. The actiovation is tied to your CPU.
If you run into problems, then:
Unfortunately, only Adobe customer service can assist you with your issue. These are user forums; you are not addressing Adobe here.
Click on the link below, and after that click on "Still need Help? Contact us."
Then on the next page, click Chat
There is also a phone option. 1 (800) 833-6687
http://helpx.adobe.com/contact.html?step=PHXS_downloading-installing-setting-up_licensing- activation -
Custom icon per entry in the AS2 Tree Component (using CS3)
I have a tree component that loads its data from an XML file and I wonder if I can customize every entry to have its own icon by adding an icon attribute to every entry in the XML and giving the tree an action to read that icon (which would exist in the library of the Flash file). My goal is to reproduce a tree within an application that my company is developing (it's for a training tool related to that application).
My XML says something like <node label = 'Label' heading = 'LABEL' desc = 'Description' icon = 'icon1' />
My label is what the tree displays, the heading is what the information dialog in the training tool displays as a title bar, the desc is what the training tool displays within the body of the text for the function description and the icon is what I want to be a reference to the graphic in the library to place as an icon in front of the item rather than use setStyle with the properties for disclosure, leaf, and folder icons.
Is that possible? I haven't found a solution for it yet.I've never used the Tree component, so I'm just guessing here....
There is a slight delay before the xml file loads and your tree has its data provider.
Perhaps during that time there is no node at mTree.getTreeNodeAt(0) to open? Try adding this just before the last line of your code:
trace("the node is: "+mTree.getTreeNodeAt(0));
What do you get?
You might need to move that code inside the xml's load event handler.
Another thing is that the Flash components tend to work on an invalidate-then-wait-one-frame-to-redraw kind of model. So it is possible you will need to wait one frame after the xml has loaded and then tell it to open that node.
The doLater method might help with that.
var home:MovieClip=this;
var xmlTreeData:XML = new XML();
xmlTreeData.onLoad = function() {
mTree.dataProvider = this.firstChild;
mTree.doLater(home,"delay");
xmlTreeData.ignoreWhite = true;
xmlTreeData.load("xml/treeValues1.xml");
mTree.setStyle("fontSize","11");
mTree.setStyle("selectionColor","0xE0E0E0");
mTree.setStyle("useRollOver",false);
function delay(){ -
My imac is doing strange things:
-delaying between users: when closing session it goes to blue, then takes a while to appear users signin box, and then wont recognize mouse command to enter until a couple of minutes later... then everything seems alright until....
-it gets stuck between things, the rainbow wheel appears and its just delays there forever....
-and every now and then the mouse starts flickering and bouncing wildly onscreen.
I ran the appel hardware test and it detected an error:
4MOT/4/40000003:HDD-1233
Does anybody know what that means? HELP!WZZZ answered about where to get iStat. And do check the SMART status. If it is an overheating problem due to a fan or logic board problem, your hard drive is possibly cooking itself to death. If so it isn't a faulty hard drive even though the hard drive might fail. So assuming it's a temperature problem, even if you are able to repair things on the disk with software, that is working on symptoms, not causes. I could be wrong however.
RE: AppleCare: Your iMac came with one year of AppleCare (Apple's warranty program), but within the first year you can buy 2 more years. You have to extend by the one year anniversary of purchase of the computer. Your 10,1 is too old to still be in the first year, and since you asked what it was, I'm sure you don't have it. Bottom line meaning is that whatever this problem turns out to be, you'll have to pay for it. Unless there is something like this. It is for 2011 iMacs with certain Seagate drives. You can put in your serial number for fun, but it looks like yours is too old. Lastly, some people have had Apple help them anyway if it is just out of warranty, but many have not. Your machine is one of these. Type in 10,1 in the search box. Is there an Apple Store near you? Just b/c it's out of warranty doesn't mean you shouldn't have it looked at by Apple. But no one here can say at all what Apple will or will not do.
Hope you get it taken care of! -
Access 2013 crashed when I export a table from the access
Hi!
Access 2013 always crashed when I export a table from the access to the Database Symfoware.
1、The conditions of the Access 2013 crashed are the follows.
1)Create a table in the Access 2013.
2)Using the ODBC driver of the Database Symfoware to export the table from the access to the Database Symfoware.
2、The Environments are the follows.
1)Access 2013 X64(Version:15.0.4420.1017)
2)Win2008R2 X64
3)Symfoware V11.1 X64
3、The Application log from the Win2008R2 are follows.
ログの名前: Application
ソース: Application Error
日付: 2014/04/18 16:21:06
イベント ID: 1000
タスクのカテゴリ: (100)
レベル: エラー
キーワード: クラシック
ユーザー: N/A
コンピューター: WIN-29UTU2AIK6J
説明:
障害が発生しているアプリケーション名: MSACCESS.EXE、バージョン: 15.0.4420.1017、タイム スタンプ: 0x50674523
障害が発生しているモジュール名: ACECORE.DLL、バージョン: 15.0.4420.1017、タイム スタンプ: 0x506742b7
例外コード: 0xc0000005
障害オフセット: 0x0000000000171f36
障害が発生しているプロセス ID: 0xb6c
障害が発生しているアプリケーションの開始時刻: 0x01cf5ad638668c5b
障害が発生しているアプリケーション パス: C:\Program Files\Microsoft Office\Office15\MSACCESS.EXE
障害が発生しているモジュール パス: C:\Program Files\Common Files\Microsoft Shared\OFFICE15\ACECORE.DLL
レポート ID: 00e87957-c6ca-11e3-ad2c-0050568d2ced
イベント XML:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Application Error" />
<EventID Qualifiers="0">1000</EventID>
<Level>2</Level>
<Task>100</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2014-04-18T07:21:06.000000000Z" />
<EventRecordID>3442</EventRecordID>
<Channel>Application</Channel>
<Computer>WIN-29UTU2AIK6J</Computer>
<Security />
</System>
<EventData>
<Data>MSACCESS.EXE</Data>
<Data>15.0.4420.1017</Data>
<Data>50674523</Data>
<Data>ACECORE.DLL</Data>
<Data>15.0.4420.1017</Data>
<Data>506742b7</Data>
<Data>c0000005</Data>
<Data>0000000000171f36</Data>
<Data>b6c</Data>
<Data>01cf5ad638668c5b</Data>
<Data>C:\Program Files\Microsoft Office\Office15\MSACCESS.EXE</Data>
<Data>C:\Program Files\Common Files\Microsoft Shared\OFFICE15\ACECORE.DLL</Data>
<Data>00e87957-c6ca-11e3-ad2c-0050568d2ced</Data>
</EventData>
</Event>
4、When the access crashed,I got the dump file .Then I use the Windbg got some information from the dump files.
The detailes are follows.
FAULTING_IP:
+58872faf03d6dd84
00000000`00000000 ?? ???
EXCEPTION_RECORD: 00000000001723c0 -- (.exr 0x1723c0)
ExceptionAddress: 000007fee3951f36 (ACECORE+0x0000000000171f36)
ExceptionCode: c0000005 (Access violation)
ExceptionFlags: 00000000
NumberParameters: 2
Parameter[0]: 0000000000000000
Parameter[1]: 0000000000000000
Attempt to read from address 0000000000000000
FAULTING_THREAD: 00000000000010b8
DEFAULT_BUCKET_ID: WRONG_SYMBOLS
PROCESS_NAME: MSACCESS.EXE
ADDITIONAL_DEBUG_TEXT:
Use '!findthebuild' command to search for the target build information.
If the build information is available, run '!findthebuild -s ; .reload' to set symbol path and load symbols.
MODULE_NAME: ACECORE
FAULTING_MODULE: 0000000076eb0000 ntdll
DEBUG_FLR_IMAGE_TIMESTAMP: 506742b7
ERROR_CODE: (NTSTATUS) 0x80000003 - {
EXCEPTION_CODE: (NTSTATUS) 0x80000003 (2147483651) - {
MOD_LIST: <ANALYSIS/>
CONTEXT: 0000000000171ed0 -- (.cxr 0x171ed0)
rax=0000000001be3598 rbx=0000000000000000 rcx=01cf5d1b0f402a5c
rdx=0000000009cfad30 rsi=0000000006688ef0 rdi=0000000001be35d0
rip=000007fee3951f36 rsp=0000000000172490 rbp=00000000001727a0
r8=0000000009b409d0 r9=0000000006688ef0 r10=0000000000000000
r11=0000000000000246 r12=0000000000000000 r13=0000000001be19f0
r14=0000000009cfad30 r15=0000000000000000
iopl=0 nv up ei pl nz na po nc
cs=0033 ss=002b ds=002b es=002b fs=0053 gs=002b efl=00010206
ACECORE+0x171f36:
000007fe`e3951f36 4d3927 cmp qword ptr [r15],r12 ds:00000000`00000000=????????????????
Resetting default scope
PRIMARY_PROBLEM_CLASS: WRONG_SYMBOLS
BUGCHECK_STR: APPLICATION_FAULT_WRONG_SYMBOLS
LAST_CONTROL_TRANSFER: from 000007fee395c095 to 000007fee3951f36
STACK_TEXT:
00000000`00172490 000007fe`e395c095 : ffffffff`ffffffff 00000000`00000000 00000000`01bddaa2 ffffffff`ffffffff : ACECORE+0x171f36
00000000`001727b0 000007fe`e388f8eb : 000007fe`e399dc10 000007fe`e399dc30 000007fe`e399dc50 00000000`000000f9 : ACECORE+0x17c095
00000000`00172b50 000007fe`e388f590 : 00000000`06688ef0 00000000`00000004 00000000`000000f9 00000000`00000000 : ACECORE+0xaf8eb
00000000`00172ba0 000007fe`e388f406 : 00000000`00000004 00000000`000000f9 00000000`11cb1130 00000000`000000f9 : ACECORE+0xaf590
00000000`00172c30 000007fe`e391aee7 : 00000000`00000000 00000000`00173198 00000000`06688ef0 00000000`11cb0998 : ACECORE+0xaf406
00000000`00172c70 000007fe`e3933a72 : 00000000`00400100 00000000`00000002 00000000`00000001 00000000`06688ef0 : ACECORE+0x13aee7
00000000`00172e50 000007fe`e384e5b1 : 00000000`00000000 00000000`11cb0020 00000000`06688ef0 00000000`00000001 : ACECORE+0x153a72
00000000`00172e90 000007fe`e38358d1 : 00000000`000007ff 00000000`06688ef0 00000000`01bd99f0 00000000`00000000 : ACECORE+0x6e5b1
00000000`00173280 000007fe`e38718eb : 00000000`000007ff 00000000`06688ef0 00000000`11cb0000 00000000`00000000 : ACECORE+0x558d1
00000000`00173340 00000001`3f3b0cd2 : 00000000`0a0945c0 00000000`000000fe 00000000`000007ff 00000000`00000000 : ACECORE+0x918eb
00000000`00173430 00000001`3f3b0b9b : 00000000`00173730 00000000`001741e0 00000000`065e5b00 00000000`00000100 : MSACCESS!CreateIExprSrvObj+0x16af32
00000000`00173630 00000001`3f3afcea : 00000000`00173730 00000000`00000000 00000000`00000000 00000000`065e5b00 : MSACCESS!CreateIExprSrvObj+0x16adfb
00000000`001736a0 00000001`3f983140 : 00000000`00174401 00000000`0a3235e0 00000000`0a319aa0 00000000`00179fc8 : MSACCESS!CreateIExprSrvObj+0x169f4a
00000000`00174290 00000001`3f3aabeb : 00000000`00000000 00000000`00000000 00000000`00179f38 00000000`00000000 : MSACCESS!FUniqueIndexTableFieldEx+0x26ab4
00000000`00174530 00000001`3f3a9670 : 00000000`001778e0 00000000`00179f38 00000000`00000031 00000000`00000000 : MSACCESS!CreateIExprSrvObj+0x164e4b
00000000`00177870 00000001`3f3a8c1b : 00000000`00000010 00000000`108c5990 003d0044`00570050 00000000`74ac3f69 : MSACCESS!CreateIExprSrvObj+0x1638d0
00000000`001779d0 00000001`3f5450df : 00000000`0a0945c0 00000000`0000009c 00000000`0a0945c0 00000000`00000000 : MSACCESS!CreateIExprSrvObj+0x162e7b
00000000`00179e30 00000001`3f64e915 : 00000000`43ed8000 00000000`00000000 00000000`3f800000 00000000`00000000 : MSACCESS!FillADT+0x5830b
00000000`0017c450 00000001`3f33b172 : 00000000`00000000 00000000`0006075e 00000000`0017e370 00000000`00000000 : MSACCESS!IdsComboFillOfActidIarg+0xaddf1
00000000`0017d730 00000001`3f33a9ef : 00000000`0017e0a0 00000000`00000b86 00000000`00000000 00000000`0fea0000 : MSACCESS!CreateIExprSrvObj+0xf53d2
00000000`0017d790 00000001`3f33a20c : 00000000`06620400 00000000`00000000 00000000`00000001 00000000`0017e420 : MSACCESS!CreateIExprSrvObj+0xf4c4f
00000000`0017e400 00000001`3f6019cd : 0071023b`007a000a 00000000`00374a30 00000000`00000005 00000000`0000000c : MSACCESS!CreateIExprSrvObj+0xf446c
00000000`0017e850 00000000`06706fd5 : e2504700`aa00ee81 00005d1b`0f2363ea 00000000`0017e9e0 00000001`3f200000 : MSACCESS!IdsComboFillOfActidIarg+0x60ea9
00000000`0017e8f0 00000000`0a30c378 : 00000000`00000000 00000000`00000008 00000000`067069ac 00000000`00000000 : 0x6706fd5
00000000`0017e960 00000000`00000000 : 00000000`00000008 00000000`067069ac 00000000`00000000 00000000`00000008 : 0xa30c378
FOLLOWUP_IP:
ACECORE+171f36
000007fe`e3951f36 4d3927 cmp qword ptr [r15],r12
SYMBOL_STACK_INDEX: 0
SYMBOL_NAME: ACECORE+171f36
FOLLOWUP_NAME: MachineOwner
IMAGE_NAME: ACECORE.DLL
STACK_COMMAND: .cxr 0x171ed0 ; kb
BUCKET_ID: WRONG_SYMBOLS
FAILURE_BUCKET_ID: WRONG_SYMBOLS_80000003_ACECORE.DLL!Unknown
WATSON_STAGEONE_URL: http://watson.microsoft.com/StageOne/MSACCESS_EXE/15_0_4420_1017/50674523/unknown/0_0_0_0/bbbbbbb4/80000003/00000000.htm?Retriage=1
Followup: MachineOwner
5、Where the access crashed I used the ODBC trace to get the trace log of the ODBC API.
The ODBC API called by Access before it crashed are the follows.
I also ansysised the log,and I did not find any Abnormal.
Test 1174-10f0
EXIT SQLGetData with return code 0 (SQL_SUCCESS)
HSTMT 0x0000000009F7C490
UWORD
6
SWORD
-8 <SQL_C_WCHAR>
PTR 0x00000000002C1F20 [
12] "LENGTH"
SQLLEN 62
SQLLEN * 0x00000000002C1E38 (12)
Test 1174-10f0
ENTER SQLGetData
HSTMT 0x0000000009F7C490
UWORD
10
SWORD
99 <SQL_C_DEFAULT>
PTR <unknown type>
SQLLEN 4
SQLLEN * 0x00000000002C1E38
Test 1174-10f0
EXIT SQLGetData with return code 0 (SQL_SUCCESS)
HSTMT 0x0000000009F7C490
UWORD
10
SWORD
99 <SQL_C_DEFAULT>
PTR <unknown type>
SQLLEN 4
SQLLEN * 0x00000000002C1E38 (-1)
Test 1174-10f0
ENTER SQLFetch
HSTMT 0x0000000009F7C490
Test 1174-10f0
EXIT SQLFetch with return code 100 (SQL_NO_DATA_FOUND)
HSTMT 0x0000000009F7C490
Test 1174-10f0
ENTER SQLFreeStmt
HSTMT 0x0000000009F7C490
UWORD
0 <SQL_CLOSE>
Test 1174-10f0
EXIT SQLFreeStmt with return code 0 (SQL_SUCCESS)
HSTMT 0x0000000009F7C490
UWORD
0 <SQL_CLOSE>
6、I also did the test with the Access 2010,and with the Sql Srever/Oracle.
The results are the follows.
1) With the Access 2010(X86 or X64) and Access 2013 X86,it successes when I export the table to the DB Symfoware.But only with the Access 2013 X64,the Access crashed.
2)With the Access 2010(X86 or X64) and Access 2013(X86 or X64),using the Sql Srever/Oracle,it always successes .
According to all the descrived above, I wonder if it a bug of the Access2013 .
Could anyone can help me ?
Thanks for any help.George Zhao
Thank you for your help.
I have already install
the latest patches of the Office 2013.But it doesn't work.It is down also too. And ODBC
drive of Database Symfoware is the newest driver of the Database Symfoware. Now I wonder that
if it si a bug of the ODBC
drive of Database Symfoware,I should fix the bug,but I have analysised the odbc trace log and I do not find any wrongs ,so I think maybe it is a bug of the Access .
I have see many situations about the Access down on the internet . -
I have a mac mini with an i7 dual core processor. It is perceptably slower than my macbook pro with a quad core i7. Does the mac mini server have the same hardware configuation as the regular mac mini with server software or is the hardware different (aside from the i7 quad core and dual hard drives)? I want a mini with a quad core i7...
Your assumption is correct. The server does however only
have the Intel HD3000 graphics like the base model with
no option, at this time, for the discrete graphics chip. So,
depending on what you are using it for, that could be a deal
breaker. Remember that your MBP does have a discrete
graphics chip.
I have a 2011 Mini Server connected to a Thunderbolt display
that gets used as an engineering workstation and general
personal use (some photo editing, LP restoraton, general
internet browsing). You simply just not enable any of the
server services. I find the combination to work quite well
for my purposes. I also have a 13" 2.7 GHz i7 Macbook Pro
which is pretty much strictly for work. As far as CPU
power it is pretty much equivelent to your Mini. For the most
part I find the Mini does outperfom my MBP. I heavily use
Parallels and Windows7 virtual machines, so the more cores
the better.
So, If you do a lot of CPU intensive stuff that is multithreaded,
the Server may help. If it is graphics intensive and your software
heavily leaverages the GPU, you may actually take a hit on
performance. -
F110- not able to clear the debit and credit entry with the same reference
Hi,
I am not able to clear the debit and credit entry with the same reference in F110 even after having the payment terms as immediate payment, payment method is maintained in document no and vendor master data. Both debit and credit entry is appearing in FBL1N as an open item but it is not appearing in F110.
In Log message appear as 8 days grace period is existing whereas as payment term is just 0001- immediate payment.
Kindly advice me what could be wrong.
Thanks,
Manya.Hi,
Credit and debit balance in vendor account are not cleared automatically when only vendor line item has payment method and credit memo has not payment method. Also when there is not payment method maintained in vendor master data.
In such case to avoid payment to vendor when vendor has debit balance we perform debit balance check.
In second scenario when u2018individual paymentu2019 is selected in vendor master data vendor invoice and credit memo are not cleared automatically in F110.
To setoff vendor credit and debit balance in F110 you to uncheck u2018individual paymentu2019 check in vendor master data > company code data > payment data.
Thanks!
Raju
Maybe you are looking for
-
Why does add-ons Manager create a new tab every time I go to home page?
When I start Firefox my home page tab shows up along with an add-ons Manager tab and a plus sign for new tab. Every time I go to a web site and then return to my home page ANOTHER add-ons Manager tab shows up. This apparently will go on forever. I ha
-
Do I need antivirus software for iPad and iPhone
I'm new to the apple world and enjoying the gadgets. Just wondering if I need to purchase antivirus software for my iPad and iPhone.
-
I have downloaded multiple purchased (not rented) movies on my computer from the iTunes store and done multiple "syncing" sessions. NONE of my purchased movies are in my iPad. Yes, I checked videos, iTunes and every other app on my iPad but they are
-
Helllo , I'm using Jdeveloper 10g , I hope If any one can help me in caching static content in my page " Images and CSS and JS libraries " I use The AFC library and the page cach the static content for the same window , but if I open new window the p
-
Unfortunately I installed Premiere Elements 8 in german, so I don't know the exact phrase how the function is called in english. It's default key is "X", hope you know, what I look for. My question: I made a lot of changes and settings and now want t