CSS 11506 problem
Hi All,
I have two portals which are located behind the load balancer (client side), the configuration is basic.
I have faced a problem on accessing these protal via SSL port (HTTPS) using the virtual Ip address which represents them, knowing that the SSL sessions are terminated on the portals not on the CSS.
any help please.
thank alot.
Mo
what kind of problem ???
Get a sniffer trace on client and server and see what is going on.
We'll also want to see the config even if basic.
Gilles.
Similar Messages
-
CSS 11506 page requests not directed properly
CSS 11506 sitting in front of mainframe and
two Windows 2003 servers
content rule3056gif
add service web1
add service web2
vip address 10.10.200.252
balance aca
url "/IMAGE_DIRECTORY_NAME/*.gif"
port 3056
active
A small number of page requests, that do not match the above pattern, are passing to the content servers web1 or web2 instead of the mainframe.
Any ideas appreciated.when a connection comes in and matches the rule above, a flow is created to switch all traffic between client and server.
If inside this same flow a new request comes in for a different content rule, the flow needs to be remapped to the new server.
This works fine except when the flow stays idle.
A flow that was idle can't be remapped.
All new requests will be sent to the current/last server even if the request does not match the rule.
The solution is to increase the idle timeout.
You can do this with a 'flow-timeout-multiplier'.
A large value will reduce a lot the chance to see the problem but it also means the amount of resources being used will increase as each flow will remain longer in memory.
It's up to you to find the right balance.
You can do a 'flow stat' from llama mode to see number of free flows and active flows.
I would say you start with a flow-timeout-multiplier of 100 and reduce or increase it if necessary.
Regards,
Gilles.
- please take a moment of your time to rate this answer. -
Trying to understand SSL sticky with CSS 11506 / ssl-l4-fallback behavior
Dear experts
I have a CSS 11506 (v7.50) which is used to load balance several SSL-based sites. We use the following textbook content rule:
content mysite-SSL
vip address 10.0.0.1
add service s01
add service s02
add service s03
port 443
protocol tcp
advanced-balance ssl
application ssl
flow-timeout-multiplier 225
active
If I read the manual correctly, SSL L3 session IDs are going to be used till a flow is set up. Then the ssl-l4-fallback (it is enabled) directive kicks in and load balancing is done based on the source IP, destination port.
However, my stats show:
Sticky Statistics - SFM Slot 1, Subslot 1:
Total number of new sticky entries is 4937735
Total number of sticky table hits is 33476045
Total number of sticky rejects (no entry) is 0
Total number of sticky collision is 0
Total number of available sticky entries is 0
Total number of used sticky entries is 131071
Total L3 sticky entries are 131
Total L4 sticky entries are 0
Total SSL sticky entries are 130940
Total WAP sticky entries are 0
Total number of SIPCID sticky entries is 0
So, why don't I see anything in the L4 sticky entries?
Also, I would expect that once the ssl-l4-fallback kicks in, a client will be always directed to the same server (since the CSS uses now source IP, dest port for load balancing). However, if I close and start again my browser I hit a different server.
Your thoughts and suggestions are highly appreciated.
John.Hi Gilles
Thank you for your response. If I may ask the group for a final further clarification, so as to put this matter to rest. Since there are a lot of frames transmitted in either direction, I would expect the following to be happening and overriding the use of SSLv3 session IDs. Following is the section of the manual that seems to contradict what you say (and I see on the stats). Am I reading the manual wrong?
"Cisco Content Services Switch
Content Load-Balancing
Configuration Guide
Software Version 8.20
November 2006
page 11-14
Configuring SSL-Layer 4 Fallback
Insertion of the Layer 4 hash value into the sticky table occurs when more than
three frames are transmitted in either direction (client-to-server, server-to-client)
or if SSL version 2 is in use on the network. If either condition occurs, the CSS
inserts the Layer 4 hash value into the sticky table, overriding the further use of
the SSL version 3 session ID." -
Hi All, 10 years since I've been on here (in the days of tables) I have, I'm sure a very basic css float problem in the footer and hopefully someone could take the time to review it for me. I have checked everything but can't find the problem. Thanks in advance;
example of problem here http://davidbrown.ipower.com/template/template.htm
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="Content-Type" content="text/html; charset=utf-8" />
<title>Our Jewelry Retail Secrets - Thank You</title>
<link href="../stylesheet/style.css" rel="stylesheet" type="text/css" />
<style type="text/css">
<!--
.H1_black {color: #000000}
p {
font-family: Arial, Helvetica, sans-serif;
font-size: 16px;
line-height: 25px;
font-weight: normal;
color: #000000;
body {
margin-left: 0px;
margin-top: 0px;
margin-right: 0px;
margin-bottom: 0px;
.headlinetxt_colour {color: #FF6600}
.style1 {color: #ff6600}
-->
</style>
</head>
<body>
<div id="wrapper">
<div id="wrapperfix">
<div id="toporange_bg">login</div>
</div>
<div id="wrapperfix_top_grey">
<div id="top_grey_content_wrapper">
<div id="big_logo"></div>
<div id="welcome_user">Welcome "username here"</div>
</div>
</div>
</div>
<div id="main_content">
<p>
<!--main body content goes here -->
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Nam vel felis velit. Proin a nisl diam, id hendrerit lectus. Nunc eget tortor arcu. Mauris fringilla felis eget mi facilisis vel auctor est lacinia. Sed sit amet dui nibh, in varius metus. Duis malesuada euismod tortor eget lacinia. Donec pretium rutrum nunc, sagittis condimentum elit aliquam in. In eu mauris dui. Lorem ipsum dolor sit amet, consectetur adipiscing elit.</p>
<p> Nam vel felis velit. Proin a nisl diam, id hendrerit lectus. Nunc eget tortor arcu. Mauris fringilla felis eget mi facilisis vel auctor est lacinia. Sed sit amet dui nibh, in varius metus. Duis malesuada euismod tortor eget lacinia. Donec pretium rutrum nunc, sagittis condimentum elit aliquam in. In eu mauris dui. </p>
</div>
<div id="footer_container">
<div id="footer">
<div id="footer_left">Footer Left</div>
<div id="footer_centre">Footer Centre</div>
<div id="footer_right">Footer Right</div></div>
</div>
</body>
</html>
#footer_container {
background-color: #333333;
width: 100%;
top: 0px;
margin: 0px;
padding: 0px;
#footer {
background-color: #666666;
min-width: 1000px;
margin-right: auto;
margin-left: auto;
padding: 0px;
width: 1000px;
height: 150px;
overflow: hidden;
clear: both;
margin-top: 0px;
margin-bottom: 0px;
position: relative;
#footer_left {
float: left;
width: 33%;
margin: 0px;
padding: 0px;
height: 150px;
#footer_centre {
width: 33%;
height: 150px;
margin: 0px;
padding: 0px;
float: left;
#footer_right {
float: left;
width: 33%;
height: 150px;
margin: 0px;
padding: 0px;I still don't see the #footer_left rule in the CSS in the online example at
http://davidbrown.ipower.com/template/template.htm -
CSS 11506 / install Disclaimer page
We have a CSS 11506. Our public portal web servers are behind that CSS 11506. How to configure the CSS so that when people click on some external websites URLs on the public portal, there will be a disclaimer / exit page shows up first.
The CSS is only loadbalancing the http traffic to the public portal web servers and does not run an http stack itself. As such the CSS is incapapble of presnting any http content to the client . Any disclamer / exit pages would need to be programmed into the content of the page the public portal server presents to the client. There is not a way to accomplish this on the css.
-
i'm looking at doing a etherchannel/channel group to CSS 11506 for greater bandwidth on the front of the CSS.. clinets>chan-group>vip>CSS >servers.
has anyone else done this?
reason i ask if this can be done is that the backup (ASR) CSS vir-peer shows as master(backup router) state. i didn't see any commands on css for etherchan, pagp or lacpHI,
etherchannel is not supported on the CSS from my knowledge. Furthermore you should avoide any spanningtree issue on the CSS. If you need more throughput than 1 GIG think about splitting the VIPs so that one CSS is active for the first half of the VIPS and the otherone for the 2nd part. Be aware that the Gateway on both VIP-pars need to be active on the correct box.
Kind Regards,
Joerg -
CSS 11506 - Locked up but cannot find why
I have had a CSS 11506 lock up with no access or activity. From the syslog logs I cannot see any error messages reporting a failure, just a hole. During the lockup I had no access to the equipment.
Any suggestions on how to investigate the lock up ?
Thank you in advance.
Roger.Hi Roger,
Based on the symptons I guess CSS did not save any core, can you double check.
I would say that we have no enough evidence to say what caused the outage, actually I would need to see the showtech and look for some evidence but I can tell you for sure that your code needs to be upgraded.
7.50 train is not getting new releases since new tains are 8.10 and 8.20 and also 7.50.103 is a early release on that train and many defects were addressed on newer codes, some of them related to crash and hung issues.
Hope it helps!! -
I configured VIP on my CSS 11506. I created a content rule and a service, which will be used by the content rule. Both have been activated. However, when I do "show service summary", the new service created is not coming up, it's showing down. I removed the service and re-created it and still down. My VIP won't work if the service remains down. Please help if you experience this before. Thanks so much !!
Collin,
You are the man! I removed th keepalive by typing "keepalive type none" initially it was "keepalive type tcp" and now the service is up and I can get to my VIP. Thanks so much! I appreciated. How should I give you a credit ? -
Is this Cf or CSS causing problem?
I am on the home stretch on this job. I have this one irritating problem and I am not sure if the prob is being caused by a <cfinput> tag or a style sheet
problem. Maybe someone out there can help identify what's happening. My guess is that it is in the CSS, but pulling my hair out to find it.
You will have to go to this page: http://www.renobowls.com/leagues/leagueRegSelect.cfm and click on "Individual Reg" button.
Look at the radio buttons underneath "Step One: Individual Registration"
I cannot get these suckers to line up in a single line. Here is the code:
<div class="box2">
<table>
<tr>
<td width="100%">
Are you a returning Reno Bowls league player?
</td>
<td width="50%">
<strong>NO</strong> <cfinput type="radio" class="fleft" name="priorRBLeague" value="No" checked="no">
</td>
<td>
<strong>YES</strong><cfinput class="fleft" type="radio" name="priorRBLeague" value="Yes" checked="Yes">
</td>
</tr>
</table>
</div>
Here is the CSS:
/*box2*/
.box2{ background:#e8e8e7; width:100%;}
.box2 .indent-box-1{ padding:35px 0 0 0; }
Inherited CSS: (going backwards)
div.container { overflow:hidden; width: 100%}
then:
/*box*/
.box{ background:#fdfdfd; width:100%;}
.box .border-top {background:url(images/border_top.gif) repeat-x top;}
.box .border-bottom {background:url(images/border_bottom.gif) repeat-x bottom;}
.box .border-left {background:url(images/border_left.gif) repeat-y left;}
.box .border-right {background:url(images/border_right.gif) repeat-y right;}
.box .corner-top-left {background:url(images/corner_top_left.gif) no-repeat left top;}
.box .corner-top-right {background:url(images/corner_top_right.gif) no-repeat right top;}
.box .corner-bottom-left {background:url(images/corner_bottom_left.gif) no-repeat left bottom;}
.box .corner-bottom-right {background:url(images/corner_bottom_right.gif) no-repeat right bottom; width:100%; }
.box .indent-box{ padding:35px 35px 17px 35px; }
then:
/*T-Reg*/
#tReg { font-size:0.75em; width:100%; text-align:left;}
#tReg .indent-main{padding:0 67px 0 67px}
#tReg .title{ background:url(images/bg_title.gif) repeat-x top; text-align:center}
#tReg .title h2{ margin-bottom:5px}
#tReg .img-left{ float:left; margin:0 20px 16px 0}
#tReg .img-left1{ float:left; margin:0 20px 0 0}
#tReg .img-indent{ margin:0 0 16px 0}
#tReg .img-indent1{ margin:0 12px 6px 0}
#tReg p{ margin:0 0 17px 0}
#tReg .p{ margin:0}
#tReg .p1{ margin:0 0 17px 0; width:100%}
#tReg .p2{ margin:0 0 7px 0}
#tReg h4{color:#6d6d6d; font-size:1em; }
#tReg h5{color:#2a88d8; font-size:.916em; text-transform:uppercase; margin-bottom:5px }
#tReg h2{color:#3b3e40; font-size:1.66em; text-transform:uppercase; margin-bottom:15px; line-height:1.2em }
#tReg .h2{color:#0f2f55; font-size:1.66em; text-transform:uppercase; margin-bottom:5px }
#tReg .h2 span{color:#1e5597; text-transform:none; font-weight:normal}
#tReg .tail{ background:url(images/tail.gif) repeat-x bottom; padding-bottom:17px; margin-bottom:17px}
#tReg ul{margin:0; padding:0; list-style:none;}
#tReg ul li{background:url(images/marker.gif) center left no-repeat; background-position:1 1px; margin:0; padding-left:18px; }
#tReg ul li a{color:#6d6d6d; text-decoration:none ; line-height:2em; font-weight:bold}
#tReg ul li a:hover { text-decoration:underline; }
#tReg .indent{padding:28px 0 0 0}
#tReg .indent-1{padding:0 0 0 128px}
.txt1{ color:#6d6d6d; font-weight:bold}
.txt2{ color:#b72723; font-weight:bold}
finally:
body {font-size:100%; line-height:1em; background:url(images/bg.gif) repeat-x #03162a; position:relative;}try this:
<div class="box2">
<table>
<tr>
<td width="100%">
<table style="width:100%">
<tr>
<td><nobr>Are you a returning Reno Bowls league player?</nobr></td>
<td><strong>NO</strong></td>
<td><cfinput type="radio" class="fleft" name="priorRBLeague" value="No" checked="no"></td>
<td><strong>YES</strong><cfinput class="fleft" type="radio" name="priorRBLeague" value="Yes" checked="Yes"></td>
</tr>
</table>
</td>
</tr>
</table>
</div> -
I should start this by saying I am very new to CSS layouts,
and am self taught, so I'm probably doing something very wrong. So
far I've stuck to really simple layouts and had no problems...but
they were very simple layouts.
With the site I'm doing at the moment I have placed other
div's inside a content div, so that I can have left and right hand
content within the content div. But the left and right div's are
not pushing the content div down with their content, and I'm not
sure what else to try to get it to work.
I've tried setting the height of the content div to auto or
inherit but that doesn't work.
As you can see on the main page of the site I'm using a
background image in the content cell.
http://members.westnet.com.au/zelky/surfschoolnew/index.html
And if you look at the details page you can see what I am
trying to describe. The content div not pushing down with the left
and right content div’s contents means the background image
is just a few pixels deep under the nav div.
http://members.westnet.com.au/zelky/surfschoolnew/details.html
And my pathetic CSS/stylesheet is here:
http://members.westnet.com.au/zelky/surfschoolnew/mainstyle.css
Thanks in advance and hopefully my mess isn’t’ to
hard to look at. As I said I'm a bit lost so hopefully I'm not
going to confuse anyone with my "home made" skills.When you 'float' elements on your page you effectively remove
them from
the normal flow of the document, therfore the 'content'
<div> thinks
nothing is inside it. You need to help it by 'clearing' the
floats.
There are various methods for clearing floats.
Insert a 'clearing' <br> (shown below) into your pages
code directly
AFTER the closing 'right' container tag and BEFORE the
closing 'content'
container tag.
</div><!-- end 'right' -->
<br style="clear: both;" />
</div><!-- end 'content' -->
zelky wrote:
> I should start this by saying I am very new to CSS
layouts, and am self taught,
> so I'm probably doing something very wrong. So far I've
stuck to really simple
> layouts and had no problems...but they were very simple
layouts.
>
> With the site I'm doing at the moment I have placed
other div's inside a
> content div, so that I can have left and right hand
content within the content
> div. But the left and right div's are not pushing the
content div down with
> their content, and I'm not sure what else to try to get
it to work.
>
> I've tried setting the height of the content div to auto
or inherit but that
> doesn't work.
>
> As you can see on the main page of the site I'm using a
background image in
> the content cell.
>
>
http://members.westnet.com.au/zelky/surfschoolnew/index.html
>
> And if you look at the details page you can see what I
am trying to describe.
> The content div not pushing down with the left and right
content div?s contents
> means the background image is just a few pixels deep
under the nav div.
>
>
http://members.westnet.com.au/zelky/surfschoolnew/details.html
>
> And my pathetic CSS/stylesheet is here:
>
>
http://members.westnet.com.au/zelky/surfschoolnew/mainstyle.css
>
> Thanks in advance and hopefully my mess isn?t? to hard
to look at. As I said
> I'm a bit lost so hopefully I'm not going to confuse
anyone with my "home made"
> skills.
>
> -
CSS layout problems in Explorer (fine in Firefox and Safari)
Firstly apologies to the mods, I had mistakenly posted this
in the dynamic section also...
My problem - I am working on a CSS site (my first!) here
http://www.benfrain.com
It appears fine in Firefox (PC and Mac) and Safari (mac) but
when I view it in Explorer for Mac (5.2.3) I get a over long page
and I get no auto margin on the left.
Another small curiosity - I have noticed that my background
image on my div id "header" seems to start off again on the right.
Again, Explorer 5.2 for mac only...
My html and css both validate.
Anybody know why this is happening?quote:
Originally posted by:
bregent
>It appears fine in Firefox (PC and Mac)
Have you tried increasing the text size?
Do you mean in the browser? I just tried it in Firefox and
after two increases the layout/style of the page kind of 'falls
apart' - how would this be rectified? -
DW CS3 CSS template problems in EI6
I'm new to CSS and DW, so I tried starting with DW's new CSS
layouts. After working on this off and on for about a year, I
finally got the design to look okay in both FF 2 and IE 7. Wouldn't
you know my client has IE 6 and the layout breaks in 6. In 6 the
middle section, including the banner image, float drop down to the
bottom. If I make the width on #container2 to be 956 pixels instead
of 950, then 6 lets the middle section float up, but all browsers
have a background colored gap between the banner images and one or
more of the sidebar images. I'm ready to pull my hair out!
Here's the link to the page set to work for IE 7 and FF and
to break in 6. The entire site, of course, has many more pages but
this just has the index because I'm experimenting.
http://www.montanahorsesales.com/shf2/
and here's the style sheet that has the problem.
http://www.montanahorsesales.com/shf2/styles/thrColFix.css
The reason I added the #container2 is to get the cream
colored background to show in both IE7 and FF. One or the other was
giving me the dark green background in the main content and the
other was giving me the cream colored main content background like
it was supposed to.
Any suggestions? Is there a quick and easy way to fix this so
it works in all browsers? Or a hack to fix it for IE 6? I can live
without it working in any IE before 6, but I need 6 to work.
In general, it is a mistake to start with DW's included CSS
layouts? I thought it would be such a smart thing to do but now I'm
not so sure!Cleo3 wrote:
> Any suggestions? Is there a quick and easy way to fix
this so it works in all
> browsers? Or a hack to fix it for IE 6? I can live
without it working in any
> IE before 6, but I need 6 to work.
Hi,
you could try replacing yours for mine...
.leftMargin198 {
margin: 0px;
padding: 0px;
height: 175px;
width: 554px;
float: left;
HTH
chin chin
Sinclair -
I'm just becoming comfortable with using CSS. At least, I
thought I was. I put together a test page and it worked on IE 7.
Then, I downloaded Firefox and Safari to check compatability on
other browsers.
I have a centered page with a top navigation bar, content
area, and a footer (bottomNavBar). Inside the content area I have
two sections, a left section and a right section. In the left there
should be text, some sort of welcome text. In the right some sort
of Flash intro video the user can play when they choose.
The problem: I got the float to work in IE 7 (Sometimes it
wouldn't. It seems tempermental.). However, the floats won't work
on the other 2 browsers. In the other 2 it puts the first div
listed above the second instead of side by side like in IE 7.
Here is the code:To make your contentIndexFlashIntro & contentIndexWelcome
divs sit
side-by-side you have to assign each a width. The combined
total of those
widths must be <=800px.
Walt
"JasonTheAdobeFan" <[email protected]> wrote
in message
news:[email protected]...
> I'm just becoming comfortable with using CSS. At least,
I thought I was. I
> put
> together a test page and it worked on IE 7. Then, I
downloaded Firefox and
> Safari to check compatability on other browsers.
>
> I have a centered page with a top navigation bar,
content area, and a
> footer
> (bottomNavBar). Inside the content area I have two
sections, a left
> section and
> a right section. In the left there should be text, some
sort of welcome
> text.
> In the right some sort of Flash intro video the user can
play when they
> choose.
>
> The problem: I got the float to work in IE 7 (Sometimes
it wouldn't. It
> seems
> tempermental.). However, the floats won't work on the
other 2 browsers. In
> the
> other 2 it puts the first div listed above the second
instead of side by
> side
> like in IE 7.
>
> Here is the code:
>
>
> ***First is the HTML***
>
> <body>
> <div class="header">
> <img src="Logo001.png" />
> </div>
> <div class="container">
> <div class="topNavBar">
> <ul class="topNavBarUL">
> <li class="topNavBarLI"><a
class="topNavBarLinksCurrent"
> href="index.htm">Home</a></li>
> <li class="topNavBarLI"><a
class="topNavBarLinks"
> href="page2.htm">Link2</a></li>
> <li class="topNavBarLI"><a
class="topNavBarLinks"
> href="page3.htm">Link3</a></li>
> <li class="topNavBarLI"><a
class="topNavBarLinks"
> href="page4.htm">Link4</a></li>
> </ul>
> </div>
> <div class="content">
> <div class="contentIndexFlashIntro">
> <script type="text/javascript">
> AC_FL_RunContent(
> 'codebase','
http://download.macromedia.com/pub/shockwave/cabs/flash/swflash.cab#
>
version=9,0,28,0','width','350','height','350','title','IntroVideo','src','Intro
> Video002','quality','high','pluginspage','
http://www.adobe.com/shockwave/downloa
>
d/download.cgi?P1_Prod_Version=ShockwaveFlash','movie','IntroVideo002'
> //end
> AC code
> </script><noscript><object
> classid="clsid:D27CDB6E-AE6D-11cf-96B8-444553540000"
> codebase="
http://download.macromedia.com/pub/shockwave/cabs/flash/swflash.cab#ve
> rsion=9,0,28,0" width="350" height="350"
title="IntroVideo">
> <param name="movie" value="IntroVideo002.swf" />
> <param name="quality" value="high" />
> <embed src="IntroVideo002.swf" quality="high"
> pluginspage="
http://www.adobe.com/shockwave/download/download.cgi?P1_Prod_Versio
> n=ShockwaveFlash" type="application/x-shockwave-flash"
width="350"
> height="350"></embed>
> </object></noscript>
> </div>
> <div class="contentIndexWelcome">
>
<!--<center><h2>Welcome</h2></center>
> <hr/>-->
> <p class="smallText">Paragraph 1</p>
> <p class="smallText">Paragraph 2</p>
> <hr/>
> <ul><u class="smallText">Unordered
List</u>
> <li><span class="smallText">Item
1</span></li>
> <li><span class="smallText">Item
2</span></li>
> <li><span class="smallText">Item
3</span></li>
> <li><span class="smallText">Item
4</span></li>
> <li><span class="smallText">Item
5</span></li>
> <li><span class="smallText">Item
6</span></li>
> </ul>
> <hr/>
> <p class="smallText">Concluding
Paragraph</p><br />
> </div>
> </div>
> <div class="bottomNavBar">
> <p>© Copyright 2008</p>
> </div>
> </div>
> </body>
>
> *********************************
> ***Next is the external CSS.***
>
> body {
> font-family: Arial, Helvetica, sans-serif;
> background-color: #999999;
> margin: 0px;
> }
>
> .header {
> background-color: #FFFFFF;
> width: 100%;
> margin: 0px;
> padding: 0px 0px 0px 0px;
> top: 0px;
> }
>
> .container {
> background-color: #FFFFFF;
> width: 800px;
> margin-left: auto;
> margin-right: auto;
> margin-bottom: 0px;
> margin-top: 0px;
> }
>
> /* top navigation bar class
> ** I prefer to have a nav bar to the top rather than the
left
> */
> .topNavBar {
> width: 800px;
> height: 22px;
> background-color: #0080EE;
> border: 0px solid #FFFFFF; /* I turned off the pixel
width because I
> didn't
> ** want a border right now. But I left the rest in case
> ** I wanted to change it back to 1px.
> */
> }
>
> /* topNavBar link properties
> ** The idea is to have each link highlight when cursor
comes over any part
> ** of the section, not just the words. Then goes back to
normal when
> cursor
> ** leaves. The current page should have its own link
highlighted always.
> */
> ul.topNavBarUL {
> height: 17px;
> float: left;
> width: 100%;
> padding: 0;
> margin: 0;
> list-style-type: none;
> }
>
> li.topNavBarLI {
> display: inline;
> }
>
> a.topNavBarLinks:link, a.topNavBarLinks:active,
a.topNavBarLinks:visited {
> float: left;
> text-decoration: none;
> color: #FFFFFF;
> background-color: #0080EE;
> padding: 0.15em 0.6em;
> border-right: 1px solid #FFFFFF;
> }
>
> a.topNavBarLinks:hover {
> color: #FFFFFF;
> background-color: #FF9900;
> text-decoration: none;
> }
>
> a.topNavBarLinksCurrent, a.topNavBarLinksCurrent:active,
> a.topNavBarLinksCurrent:visited,
a.topNavBarLinksCurrent:hover {
> float: left;
> text-decoration: none;
> color: #FFFFFF;
> background-color: #00FF33;
> padding: 0.15em 0.6em;
> border-right: 1px solid #FFFFFF;
> }
>
> /* content class
> ** This is the part of the page that the content will go
in.
> ** It should have the full width of the container class
and
> ** stretch in height based on the content with a minimum
> ** height of 500px.
> */
> .content {
> width: 800px;
> min-height: 400px;
> background-color: #FFFFFF;
> font-family: Arial, Helvetica, sans-serif;
> color: #000000;
> }
>
> /* content links
> ** The links in the content area will just be the
regular links.
> ** Navigation links will all be given special classes to
define them.
> */
> a:link, a:active, a:visited {
> color: #0080EE;
> text-decoration: none;
> }
>
> a:hover {
> color: #FF9900;
> text-decoration: underline;
> }
>
> /* content headings, hr
> */
> h1, h2, h3, h4, h5, h6 {
> font-family: Arial, Helvetica, sans-serif;
> color: #00FF33;
> margin-bottom: 2px;
> }
>
> hr {
> color: #0080EE;
> }
>
> p {
> text-indent: 20px;
> margin-top: 4px;
> }
>
> ul {
> margin-top: 4px;
> }
>
> li {
> list-style: square;
> color: #00FF33;
> }
>
> .contentIndexFlashIntro {
> padding-top: 2px;
> padding-right: 2px;
> float: right;
> }
>
> .contentIndexWelcome {
> float: left;
> text-align: justify;
> padding-top: 4px;
> padding-right: 10px;
> padding-bottom: 4px;
> padding-left: 4px;
> }
> -
I'm trying to use a default css file in a library project... I'm using this in my library's compile arguments:
"-include-stylesheet defaults.css /assets/styles/defaults.css"
In defaults.css, I'm trying to assign a defautl skin like this:
comp|Badge {
skin-class: ClassReference('com.woo.skins.BadgeSkin');
The problem is when the component is being newed:
Main Thread (Suspended: TypeError: Error #1009: Cannot access a property or method of a null object reference.)
mx.core::UIComponent/getStyle
spark.components.supportClasses::SkinnableComponent/attachSkin
spark.components.supportClasses::SkinnableComponent/validateSkinChange
spark.components.supportClasses::SkinnableComponent/createChildren
What part am I doing wrong? I'm hoping it's the -include-stylesheet part, I couldn't find a single example for using that.I assume you are using FlexBuilder to build and compile and not ant or the comand line correct? If so there are two things you need to check.
1) Where is your defaults.css located? As long as it is in the root of your library's src directory (ie. src/defaults.css) you shouldn't even need to add that compiler option. When it builds a project, FlexBuilder looks for a file named defaults.css in this location and will use it to override the framework version.
2) Go into your project properties -> build path -> assets tab. Make sure your defaults.css file is selected for inclusion. -
I have an unusual problem that must be something to do with
my Dreamweaver set-up.
All of a sudden all of my sites do not display the CSS in the
dreamweaver application. The CSS details all appear and I can
select them in the usual way but nothing appears on screen.
When I preview any page from any site in a browser it is
fine.
Does anyone have any idea what the problem might be?
Thanks
DaveVIEW | Style Rendering > Display Styles
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.dreamweavermx-templates.com
- Template Triage!
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
http://www.macromedia.com/support/search/
- Macromedia (MM) Technotes
==================
"davecheet" <[email protected]> wrote in
message
news:f65vv5$flb$[email protected]..
>I have an unusual problem that must be something to do
with my Dreamweaver
> set-up.
> All of a sudden all of my sites do not display the CSS
in the dreamweaver
> application. The CSS details all appear and I can select
them in the usual
> way
> but nothing appears on screen.
> When I preview any page from any site in a browser it is
fine.
>
> Does anyone have any idea what the problem might be?
>
> Thanks
>
> Dave
>
Maybe you are looking for
-
Hi All, Database Version: 11.2.0.3.0 We have requirement below: From the java application one of our database procedure will be called, and one of the input parameter for the procedure is part_number and it can contain multiple values, so the java se
-
Dunning for Vendor Credit Memo
Dear Expert, I have 5 open due invoices in vendor account of euro 10000 and now i have posted credit memo which is not relating to any of the invoices for value of euro1000.Now i want to run dunning only for credit memo (as this is seperate item rece
-
I need a simple MDI application
I need a simple MDI application...
-
Previewcrasch when saving pdf´s
After upgrade to 10.6 I have experienced numerous crasches when trying to save pdf´s from preview (save as). I have reinstalled the OS (clean install) and restored the rest of the system using Time Machine. Below you find a typical message (part of i
-
The md5-sparc cannot open a file with size 2GB
Hi, I would need to check the integrity of the file with size > 2GB with md5-sparc but I still get the error message "error opening file". Is there an update of this program which can open the large files, too? I have tried to search on web but witho