CUBE - Selective Outgoing Privacy Header

Hello, All!
I'd like to selectively block outbound CallerID on a SIP trunk. I've come up with two methods to block the CLID, but I'd like to know if there are better methods.
From CUCM
Create a secondary SIP Trunk with Privacy enabled. Create a Route List pointing to the SIP Trunk. Create and assign CSS on devices you'd like to have blocked CLID.
From CUBE
Setup SIP Profile, such as the below example. Apply to PSTN-Outbound Dial Peers.
voice class sip-profiles 1 request INVITE sip-header Privacy add "Privacy: id"
Issue
If blocking the CLID using the CUCM method then either you must block all CLID on a particular device or use Line CSS for PERMIT purposes, which I'm not fond of.
If blocking the CLID using the CUBE method then all matches to the dial-peer would have blocked CLID. I could potentially create a dial-peer that uses a special prefix in order to avoid overlapping, but I thought I'd check with the experts.
Ideally, I'd like to be able to tweak the sip-profile rule so that it checks the From header for particular Calling Numbers and applies Privacy based on that. However, I don't know of a way to do an if statement in sip-profiles. Any thoughts on how to best handle selective outbound CLID blocking?
Thanks as always for your invaluable support!

I'd like to be able to tweak the sip-profile rule so that it checks the From header for particular Calling Numbers and applies Privacy based on that. However, I don't know of a way to do an if statement in sip-profiles -  I can help you on this.
Here is the sample test config. Calling number - 6060 , Called number- 2444 , CUBE ip -10.0.2.3
voice class sip-profiles 1
request INVITE sip-header Remote-Party-ID modify "" ""
request REINVITE sip-header Remote-Party-ID modify "" ""
request INVITE sip-header From modify "" ""
request REINVITE sip-header From modify "" ""
dial-peer voice 100 voip
destination-pattern 2...
voice-class sip profiles 1
session protocol sipv2
session target ipv4:10.0.0.2
Now see the INVITE message.
*Jan  7 15:21:55.895: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
INVITE sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 10.0.2.3:5060;branch=z9hG4bK6582
Remote-Party-ID: [email protected]>;party=calling;screen=no;privacy=off
From: [email protected]>;tag=21DB24-2270
To:
Date: Tue, 07 Jan 2014 15:21:55 GMT
Call-ID: [email protected]
Supported: 100rel,timer,resource-priority,replaces,sdp-anat
Min-SE:  1800
Cisco-Guid: 1185875884-1994789347-2150037246-3764791837
Now the calling number is 6090
INVITE sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 10.0.2.3:5060;branch=z9hG4bK745A
Remote-Party-ID: [email protected]>;party=calling;screen=no;privacy=off
From: [email protected]>;tag=26ACB0-15F2
To:
Date: Tue, 07 Jan 2014 15:27:12 GMT
Call-ID: [email protected]
Supported: 100rel,timer,resource-priority,replaces,sdp-anat
Min-SE:  1800
Cisco-Guid: 48467858-1994854883-2150430462-3764791837
Rate all the helpful post.
Thanks
Manish

Similar Messages

  • Cube selection

    Hi All,
    1. In cube selection screen, Is it possible to disappear SID 's ( Vendor (SID)/Material (SID) ?
    2. I have a load contains 25 laks records, I can use both Doc numbers(P.key) or year wise. When I am using year wise it takes long time/Process over due error. Why? .For Doc.numbers it works fine.
    Please advise me 1 &2.Thanks in advance.
    Sri.

    Hi Edwin/Vishwesh,
    Thanks for your response.
    1. Can I disapper SID selection @ IC-> Manage--> Contents level?
    2. Not viewing the contents.Load the Data Records- Huge load.
    Last time we did a load without selection in Doc num, it loads 40 packets successfully, and remaining 12 are failed due to space problem)
    ORA 1632 problem we faced, Max extent 300 exceeded.
    We would like create multiple Ipacks now and run with different selections under a infopack Group. All Ipacks are under IpackGroup, maintained sequence numbers also.
    A Shall I get any space problem using selections?
    B. Let me know your Ideas about this huge load?
    C.  Let me know the procedure how to schedule an IPackGroup using BackGround?
    Cheers,
    Sri.

  • 75% of my messages when selected show proper header, but empty main body?

    most of the messages arriving in my inbox, look normal in the message list area, but when selected, the correct header shows, but nothing follows - i.e. the body of the message is empty. i import from gmail and hotmail - both are affected. odd;y. as i said, this is only for 3/4 the messages. an apparent 1/4 are fine. thoughts?

    fixed itself?

  • List Cube Selections

    Hi,
      In List Cube of an Info cube selection screen if i apply restriction on Company Code the cube doesn't show any data where as if i apply a restriction on Cal Year then the cube shows data and there i can find data for that particular company code....
    Why is this happening
    Thanks

    Hi,
    Just see whether improvised listcube mentioned in link below help you in getting the required result
    http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/70e092a3-9d8a-2d10-6ea5-8846989ad405?QuickLink=index&overridelayout=true
    Thanks and regards
    Kiran

  • How set disable select matrix column header

    How set disable select matrix column header same Inventory-->Pick List Form
    Thanks Advance.

    Hi ,
    do u mean Price List Form Header...
    If Yes Means Try the Following,
    select case pVal.FormType
    case "155"
    Select Case pVal.Before_Action
    case True
    select case pval.ItemUid
    case "3"
    Select Case pVal.EventType
    Case SAPbouiCOM.BoEventTypes.et_CLICK
    if pval.row = 0  Then BubbleEvent = False : Exit Sub
    End Select
    End Select
    End Select
    Regards,
    Ganesh k

  • Picture to right of outgoing mail header

    I can't be the only one to have somehow set up Mail to send a picture on my outgoing mail (it appears to the right of the header), and not been able to remove it or turn it off. Can somebody help me remove this annoyance with out destroying the rest of my Mail setup?
    Powerbook G4 aluminum   Mac OS X (10.3.9)  

    is it the same picture as you have in your login window? Do you have a "Me" card in AddressBook? Try eliminating your "Me" card (at least temporarily for verification purposes) if you don't want to look at it. If your concern is whether or not the picture is not transmitted with your message, it isn't. If you had pictures of people in your address book, when you received an email from them, you would see those pictures. But they are not sending them to you, just like you are not sending your picture out.
    As a test, if you temporarily removed your "Me" card from the address book and sent yourself a message, you would see that it isn't in your sent mail, it isn't in your received mail. Then if you sent another "pictureless" one out, and then after that, you reinstalled your "Me" vcf card in Address Book and selected a picture for that card, , then downloaded new mail, your picture is back. But you didn't send it out. Try it.
    (if you find that this solves your problem, or is actually helpful towards arriving at a solution to your problem, please consider clicking on either the "helpful" or "solved" buttons above)

  • Non Cumulative Cube selective deletion and Reload

    Hi,
    We have a typical scenario, where in the company code displays # when we execute the inventory reports at plant level,
    Upon analysis, we did find the Plant to Company code mapping was not maintained at R/3. Now this was fixed, hence we are planning to do selective reload for that particular plant alone.
    Keeping in mind the loading sequence/scenarion for Inventory, can any one advise if we need to do stock init again for this plant and reload the data after selective deletion.
    Or can we directly load from the material movement datasource. Will there be any impact ie: at marker update etc.
    Note: We already have data into this inventory cube for last 2 years.
    The cube contain aggregate compression.
    Thanks
    Ramesh

    Any inputs please
    Ramesh

  • Mail.app: Select outgoing (SMTP) server per message?

    Dear community members,
    I'm looking for a solution to the following problem:
    I do have multiple e-mail accounts which are configured in the following way: One of them is the master account (let's say [email protected]) added to Mail.app as a POP account. The other ones (let's call them [email protected] and [email protected]) are on different servers and are configured to forward all incoming mail to [email protected] They are, however, not added to Mail.app as additional accounts. That is because it's not necessary for receiving mail with these addresses, since all incoming mail is forwarded to [email protected], anyway, and therefore immediately available in Mail.app.
    The problem arises when sending e-mails within Mail.app. I can easily add all three addresses in the "Mail" > "Settings" > "Accounts" settings window by entering them in the e-mail-address-field separated by comma (e.g. "[email protected], [email protected], [email protected]“). This allows me to select the desired outgoing address on a per-message basis in the compose window.
    There is, however, a problem with this: This setting means that mail from all three addresses is being sent using the same SMTP server. This can cause problems for domains that do have SPF-records, for example. Therefore, I'd very much prefer to not only select the outgoing mail address on a per-message-basis, but also the SMTP-server I'd like to use. Since Mail.app allows me to add multiple SMTP servers in the account's settings window, I believe there has to be a way to select which one to use on a per-message-basis? Whenever there's a problem with an SMTP-server, a window opens up asking me which of the alternative SMTP servers I'd like to use, instead. This indicates that this function exists – it's just far from obvious for me where to find it in a normal usage scenario.
    Does anyone have an idea? Any hint is welcome!
    Thanks
    Nick

    That has nothing to do with it. I ended up working around the problem by changing the account name.
    But I still think this is a bug, so I won't mark the topic as answered (a workaround is not the solution).

  • How to select outgoing server automatically?

    The code below is part of Apple Mail templates. Where you see the "Trial", this is a code that automatically writes Trial into the subject line of an email when using this template.
    I have several accounts with outgoing servers. How can I put in the code below that it selects a given outgoing server that I want to pre-set?
    <?xml version="1.0" encoding="UTF-8"?>
    <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
    <plist version="1.0">
    <dict>
    <key>Background Images</key>
    <array>
    <string>bg_pattern.jpg</string>
    <string>bg_letter.jpg</string>
    </array>
    <key>Folder Name</key>
    <string>INR.mailstationery</string>
    <key>HTML File</key>
    <string>content.html</string>
    <key>Headers</key>
    <dict>
    <key>Subject</key>
    <string>Trial</string>
    </dict>
    <key>Images</key>
    <array>
    <string>top.jpg</string>
    <string>bottom.jpg</string>
    </array>
    <key>Stationery ID</key>
    <string>A978C3B3-4E0A-4045-9759-EF0690326CA8</string>
    <key>Thumbnail Image</key>
    <string>thumbnail.png</string>
    </dict>
    </plist>

    I don't think it can be don in this plist, but I think you can enable only one outgoing server in Mail, or set a default.

  • Unable to select podcast sort header

    For some reason, when I'm in my 'Podcast' library or my 'Party Shuffle' playlist, I am unable to select a different column/change the column my content is sorted by.
    With the podcasts, it is currently sorted by 'Release Date'. I can click on the that column header, inverting the order. However, if I click on the header of a different column, e.g. 'Description' or 'Track #' it responds by making the fist as if I'm trying to rearrange the order of the columns, even though I'm not moving my (track ball) mouse at all.
    The same behavior exists in the 'Party Shuffle' playlist.

    Thanks for replying, I appreciate the help.
    So I don't understand, are you saying you think that's "just the way it is"? I could have sworn I was able to column sort before, maybe I'm crazy.
    Can anyone else corroborate this is simply a "weakness" of iTunes?
    If so, any suggestions on automatically migrating my podcasts to my music library?
    Thanks

  • Can't select text in header

    Man... Just found out after build several web sites that, if you want a browser to show a title other than the explicit name of the page in the left column, you need to edit the text in the header.
    Easy enough. So now, in an existing web site I've built, I turn "show navigation menu" back on so I can see the header text. problem is, I can't select it. All the names up there are the names of my pages. If I click on the box, I can resize it, but I can't select the text at all to change it. If I click on one of the page names, it takes me to that page, so the links are working.
    To calrify... I don't want to show this header nav bar. I just want to be able to control the name that comes up in the browser frame, without actually changing the name of the page.
    Am I missing something? probably.
    Thanks.
    B

    When you first create a page there is a text box at the top just under the navbar with the name of the theme in it. Whatever is in that text box will be the text that shows in the top of the browser's window, i.e. Welcome, About Me, My Photos, etc. (that is if you don't change that text).
    If you don't want to change what you currently have you can use the following code in an HTML snippet to set the title of the page to be displayed by the browser:
    <script type='text/javascript'>
    parent.document.title = "PAGE NAME TO SHOW IN BROWSER TAB/BAR";
    </script>
    OT

  • Grouping of selections into one heading in BEX

    Dear all,
    I have a scenario
    wherein
    KF1,KF2 - Monthly
    KF3,KF4- Quarterly
    KF5,KF6 - Yearly
    The titles shoulld appear in  the columns for the key figures as the Curr month, Curr Qtr and Current year.
    I can do Key figure selections ;But to group the set of keyfigures in one heading.. How is possible?
    Please help
    Regards,
    Rajarathnam.S

    Hi Parth,
    Thanks for the reply. The key figures in each group are different. So there cant be a common structure above them
    As for ur first approach Itried that but a selection in the structure with KF demands for a KF to be aded in all the selections (This means in all the Heading selections too I need to put some Keyfigures else it is throwing up an error)
    And as u said, there are no business Logics ,these are simple headings for each group.
    Can you help more on this.
    Regards,
    Rajarathnam.S

  • Selecting outgoing mail server

    Hi All,
    I am using Mac Mail 8.1
    With previous versions I could select the outgoing mail server when composing a new email.  This option is not present in Yosemite.
    Am I wright or there is something I am not taking into consideration?
    Thanks,
    Nicolas

    Thank you Eric.
    Actually, I have followed these steps when setting up my email account on OS X Maverics, but the selection of the outgoing smtp server disappeared with OS X Yosemite.
    When composing the email, I can chose the "From" account, but on Maverics beside the From option I could also choose the outgoing server.
    This way could handle different combinations of accounts and smtp servers.  Now on Yosemite I can not do it any more.
    Thanks,
    Nicolas

  • URL, title etc of webpages do not print on pages printed off internet despite selecting these in header/footers in page set up. How do I get URL etc to print on the page?

    No matter how I try I cannot get the URL of a webpage or other options such as page title, date etc to print if I print up a webpage. I have done the necessary selections in file>page setup>headers & footers choosing the options from the drop downs. I have even tried making top or bottom margin bigger thinking there was not space on the page. This is still the case if I try to print to different printers.
    Is there something I am missing that needs to be done via some other setting or menu item?

    Thanks, this was a good idea to try, however it doesn't seem to have helped.
    I reset:
    print.print_printer
    Also tried resetting:
    print.printer_Lexmark_6500_Series.print_footercenter
    print.printer_Lexmark_6500_Series.print_footerleft
    print.printer_Lexmark_6500_Series.print_footerright
    print.printer_Lexmark_6500_Series.print_headercenter;
    print.printer_Lexmark_6500_Series.print_headerleft
    print.printer_Lexmark_6500_Series.print_headerright
    Closed and restarted the browser.
    I then selected URL in footer right in page setup but still it refuses to show in print preview or print on the page in hard print. It is most peculiar. Any other ideas? Thanks.

  • Fixed width file outgoing with header,detail and trailer in one map

    we have a scenario where in we have to create an output file. the file is fixed width with three different kinds of records namely header, details and trailer. if the specification of the metadata of the file is specified how will we incorporate the creation of the file in one map since the map produces only one call to UTL_FILE and writes it.
    there is a work around in a crude way where in we can define the file as a CSV and pass everything in an appanded string in one column. but i wanted to know how we can get the three logical records in one map..
    thanks
    kamal

    The problem is not with generating the records.. i mean header , detail and trailer.
    it is how we put them into a fixed width sampled file. if we look at the code generated we will see only one call being made to generate the file.

Maybe you are looking for