Datasocket calls from Fieldpoint - performanc​e issues
I'm noticing that it takes A LONG TIME for the fieldpoint units to READ data from a Datasocket Server. My program is currently looping and reading 4 Datasocket Items from a server computer(in a for loop) but it takes around 3 seconds for this process to occur. Any suggestions as to how i can "speed" up these datasocket reads? Would using a different protocol (to read datasockets item) be quicker?
Regis
"the loop time dropped from 3 seconds
to under 1 sec (about 750ms)"
I wanted to mention that the 750ms was a pre-defined wait time i placed
in the loop. Without a wait time, I dropped the loop time
to about 80ms.
Also, can anyone please help me with this issue?
Datasocket ReadWrite Mode
Message Edited by RegisPhilbin on 07-20-2005 11:00 AM
Similar Messages
-
My IPhone 6 128GB with current software using AT&T is dropping 5-10 calls a day. I am calling from an office with good signal strength and in the same location as i did with my 5S which almost never had dropped calls. Is this a hardware or software issue? Is this a common issue with the new IPhones?
Hi jackneedshelp,
Thanks for visiting Apple Support Communities.
If calls are not going through on your iPhone 6, I recommend going through the troubleshooting method found at this link:
iPhone: Troubleshooting issues making or receiving calls - Apple Support
These steps can help identify and resolve the symptom that might be causing the connection issue.
All the best,
Jeremy -
Quality issues with calls from US to Korea
I've always been a big fan of Skype. I have a premium account and I use "Skype to go" to call from the US to South Korea. Starting about 5 months ago, the quality of these calls has severely degraded. It is almost not worth the call. It is very difficult for me to hear the people I've called and for them to hear me as well. There is no Skype customer support contact phone number listed anywhere on the Skype website that I can find. Otherwise, I'd be addressing this issue with a real person. Is there a reason for this call quality degradation? Is there a fix in work? Is there a customer service number I can call? Is it time for me to leave Skype?
rates are available on http://www.skype.com/en/rates/ just enter Itay in the destination and check the rates lower down the page.
If you are going to make a lot of calls - check the subscriptions available too...
There are subscriptions that include landlines and mobiles as well -
Call script from script; exit code issues
I have verified in a very simple pair of scripts that I can feed an exit code back to the calling script. My "Parent" test is little more than
powershell.exe -file "$ScriptPath\child.ps1"
Write-Host "$LASTEXITCODE!!!"
and the child script is just
Exit 1
And that Write-host comes back correctly. I have even tried it with two different child scripts, with different rerun codes, being called from Parent back to back. All good.
However, in a more complicated script, where the child script has conditional exits, I am getting 0 all the time. The conditional looks like this
if ($Global:MemberofSet) {
if ($Global:ErrorOccured) {
Write-Host '1'
Exit 1
else {
Write-Host '0'
Exit 0
And even when the 1 echoes, I still get a $LASTEXITCODE of 0.
Is there some known issue here that I am not aware of? Using PS 2.0, FWIW.
Thanks!Um, no, more that I remmed out
[CmdletBinding()] at the top of each child script and with no other changes everything is working exactly as it should. Not sure why it worked, but I am certainly not imagining it.
For shits and giggles I also added the binding in my little test script set, and that is now broken,
with no other changes. I really hadn't created a good test obviously, but I wasn't expecting binding to matter. Would love to hear an explanation as to why it would
For anyone wanting to see the behavior, these are the three test scripts, and you run the Arch script. With binding enabled DTV will show 1, but return 0. Rem the
bindings and DTV will correctly return 1. I also tested RVT to not be MemberofSet, so -1 is returned, and $LASTEXITCODE shows a wonky number as expected given the bug in 2.0 and negative return codes.
NOTE: In the test the argument in the child scripts is not used, it's just there to avoid the error you otherwise get when binding. In my "live" code the
arguments are mandatory and used.
Arch_2015.ps1
powershell.exe -file "RVT_2015.ps1"
Write-Host "$LASTEXITCODE!"
powershell.exe -file "DTV_2015.ps1"
Write-Host "$LASTEXITCODE!"
DTV_2015.ps1
[CmdletBinding()]
Param ([string]$Mode)
$Global:MemberofSet = $True
$Global:ErrorOccured = $True
if ($Global:MemberofSet) {
if ($Global:ErrorOccured) {
Write-Host 'DTV 1'
Exit 1
else {
Write-Host 'DTV 0'
Exit 0
else {
Write-Host 'RVT -1'
Exit -1
RVT_2015.ps1
[CmdletBinding()]
Param ([string]$Mode)
$Global:MemberofSet = $True
$Global:ErrorOccured = $False
if ($Global:MemberofSet) {
if ($Global:ErrorOccured) {
Write-Host 'RVT 1'
Exit 1
else {
Write-Host 'RVT 0'
Exit 0
else {
Write-Host 'RVT -1'
Exit -1 -
Sound issues making phones calls from Mac
When making or receiving calls thru continuity on my Mac (27" Late 2013; IOS 8.1 iPhone 5S), the person on the other end says the call sounds like I'm in a tunnel, has some distortion and is at times not clear enough to understand what I'm saying. I have used the internal microphone on the mac and have also used a "Yeti" external microphone with the same results. I did try "Face Time" audio as a test and the sound was much improved and satisfactory at the caller's end. There are no issues with the sound from my end sitting at the computer.
Making iPhone Calls from Mac Doesn't Work
Your points 1 & 2 have nothing to do with it.
On 3, is it turned on on your iPhone and your Mac? -
Bluetooth and direct call from Outlook 2010 issue
Hello.
I connect Nokia 5300 via Bluetooth and can call from Nokia Communication Center. But when i try to call from Outlook, phone begins dialing and immediately shows strange icon "D" and break dialing.
If i connect via USB - all work without any problems - form Nokia Communication Center and from Outlook also.
In OS Nokia is shown as Standard Modem via Bluetooth (Microsoft)
PC Suite 7.1.6
Windows 7 x64 Ultimate RUS SP1
Outlook 2010 x64Workstations are on a domain
Also it may appear to be more of a issue with 2000 .pub type of files. As users can create a 2010 .pub file and it works great fine. But every time a user opens a 2000 .pub file via outlook and tries to edit and save it requests the
user to do a save as, vs. save to outlook temp location. -
Issue with selecting or copying a phone no. in dialing or direct calling from websites
Dear All,
I remarked that in Z10 I cannot use in dialing screen neither copy/paste phone numbers nor calling direct from email or websites by selecting the phone no. and taping on it.
This seems to be a bit annoying when you try to make a call from web or inside the email text, because you do not have even the possibility to paste the copied number into the dialing screen.
Somebody knows if is possible to do it, as in the other phones ?
Thanks !The dial pad does not allow you to paste a number. But within an email, text message, web site, BBM message, if its a valid phone number example 416-967-1111, it shows the number as blue, Just clik and hold it and a slider appears on the right(copy, call, send text message, View contact, share/NFC, share, ope in). If you just tap it, it will start to dial the number.
-
Error while calling ejb service call from BPM service
Hi,
We are using the Oracle 11.1.1.5.0
We are calling ejb service call from BPM service to update the data to Oracle database.
We are getting the below error when we executing the ejb service call from BPM Service.
<Error> <EJB> <BEA-010026> <Exception occurred du
ring commit of transaction Name=[EJB oracle.bpm.bpmn.engine.ejb.impl.BPMNDeliver
yBean.handleCallback(java.lang.String,java.lang.String,java.lang.String,int,bool
ean)],Xid=BEA1-45B91984D57960994897(30845116),Status=Rolled back. [Reason=javax.
transaction.xa.XAException: JDBC driver does not support XA, hence cannot be a p
articipant in two-phase commit. To force this participation, set the GlobalTrans
actionsProtocol attribute to LoggingLastResource (recommended) or EmulateTwoPhas
eCommit for the Data Source = EBSConnection],numRepliesOwedMe=0,numRepliesOwedOt
hers=0,seconds since begin=1,seconds left=60,XAServerResourceInfo[SOADataSource_
base_domain]=(ServerResourceInfo[SOADataSource_base_domain]=(state=rolledback,as
signed=soa_server1),xar=SOADataSource,re-Registered = false),XAServerResourceInf
o[ArCnTaskForms@EBSConnection@EBSConnection_base_domain]=(ServerResourceInfo[ArC
nTaskForms@EBSConnection@EBSConnection_base_domain]=(state=rolledback,assigned=s
oa_server1),xar=weblogic.jdbc.wrapper.JTSEmulateXAResourceImpl@fa5476,re-Registe
red = false),SCInfo[base_domain+soa_server1]=(state=rolledback),properties=({web
logic.jdbc.remote.EBSConnection=t3://192.168.10.114:8001, weblogic.transaction.n
ame=[EJB oracle.bpm.bpmn.engine.ejb.impl.BPMNDeliveryBean.handleCallback(java.la
ng.String,java.lang.String,java.lang.String,int,boolean)]}),local properties=({w
eblogic.jdbc.jta.SOADataSource=[ No XAConnection is attached to this TxInfo ]}),
OwnerTransactionManager=ServerTM[ServerCoordinatorDescriptor=(CoordinatorURL=soa
server1+192.168.10.114:8001+basedomain+t3+, XAResources={eis/tibjms/Queue, eis
/activemq/Queue, WLStore_base_domain_BPMJMSFileStore, WLStore_base_domain__WLS_s
oa_server1, eis/fioranomq/Topic, eis/jbossmq/Queue, eis/Apps/Apps, eis/websphere
mq/Queue, eis/AQ/aqSample, WLStore_base_domain_SOAJMSFileStore, eis/aqjms/Queue,
WSATGatewayRM_soa_server1_base_domain, eis/sunmq/Queue, eis/pramati/Queue, SSCo
nnectionDS_base_domain, eis/tibjms/Topic, eis/tibjmsDirect/Queue, eis/wls/Queue,
eis/tibjmsDirect/Topic, EDNDataSource_base_domain, eis/wls/Topic, eis/aqjms/Top
ic, RL3TST_base_domain, ArCnTaskForms@EBSConnection@EBSConnection_base_domain, S
OADataSource_base_domain, WLStore_base_domain_UMSJMSFileStore_auto_2},NonXAResou
rces={})],CoordinatorURL=soa_server1+192.168.10.114:8001+base_domain+t3+): weblo
gic.transaction.RollbackException: Could not prepare resource 'ArCnTaskForms@EBS
Connection@EBSConnection_base_domain
JDBC driver does not support XA, hence cannot be a participant in two-phase comm
it. To force this participation, set the GlobalTransactionsProtocol attribute to
LoggingLastResource (recommended) or EmulateTwoPhaseCommit for the Data Source
= EBSConnection
at weblogic.transaction.internal.TransactionImpl.throwRollbackException(
TransactionImpl.java:1881)
at weblogic.transaction.internal.ServerTransactionImpl.internalCommit(Se
rverTransactionImpl.java:345)
at weblogic.transaction.internal.ServerTransactionImpl.commit(ServerTran
sactionImpl.java:239)
at weblogic.ejb.container.internal.BaseLocalObject.postInvoke1(BaseLocal
Object.java:622)
at weblogic.ejb.container.internal.BaseLocalObject.__WL_postInvokeTxRetr
y(BaseLocalObject.java:455)
at weblogic.ejb.container.internal.SessionLocalMethodInvoker.invoke(Sess
ionLocalMethodInvoker.java:52)
at oracle.bpm.bpmn.engine.ejb.impl.BPMNDeliveryBean_of8dk6_ICubeDelivery
LocalBeanImpl.handleCallback(Unknown Source)
at com.collaxa.cube.engine.dispatch.message.instance.CallbackDeliveryMes
sageHandler.handle(CallbackDeliveryMessageHandler.java:47)
at com.collaxa.cube.engine.dispatch.DispatchHelper.handleMessage(Dispatc
hHelper.java:140)
at com.collaxa.cube.engine.dispatch.BaseDispatchTask.process(BaseDispatc
hTask.java:88)
at com.collaxa.cube.engine.dispatch.BaseDispatchTask.run(BaseDispatchTas
k.java:64)
at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExec
utor.java:886)
at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor
.java:908)
at java.lang.Thread.run(Thread.java:662)
Caused by: javax.transaction.xa.XAException: JDBC driver does not support XA, he
nce cannot be a participant in two-phase commit. To force this participation, se
t the GlobalTransactionsProtocol attribute to LoggingLastResource (recommended)
or EmulateTwoPhaseCommit for the Data Source = EBSConnection
at weblogic.jdbc.wrapper.JTSXAResourceImpl.prepare(JTSXAResourceImpl.jav
a:83)
at weblogic.transaction.internal.XAServerResourceInfo.prepare(XAServerRe
sourceInfo.java:1327)
at weblogic.transaction.internal.XAServerResourceInfo.prepare(XAServerRe
sourceInfo.java:513)
at weblogic.transaction.internal.ServerSCInfo$1.run(ServerSCInfo.java:36
8)
at weblogic.work.SelfTuningWorkManagerImpl$WorkAdapterImpl.run(SelfTunin
gWorkManagerImpl.java:528)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:209)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:178)
.>
<12 Oct, 2012 12:34:40 PM IST> <Error> <oracle.soa.bpel.engine.dispatch> <BEA-00
0000> <failed to handle message
javax.transaction.xa.XAException: JDBC driver does not support XA, hence cannot
be a participant in two-phase commit. To force this participation, set the Globa
lTransactionsProtocol attribute to LoggingLastResource (recommended) or EmulateT
woPhaseCommit for the Data Source = EBSConnection
at weblogic.jdbc.wrapper.JTSXAResourceImpl.prepare(JTSXAResourceImpl.jav
a:83)
at weblogic.transaction.internal.XAServerResourceInfo.prepare(XAServerRe
sourceInfo.java:1327)
at weblogic.transaction.internal.XAServerResourceInfo.prepare(XAServerRe
sourceInfo.java:513)
at weblogic.transaction.internal.ServerSCInfo$1.run(ServerSCInfo.java:36
8)
at weblogic.work.SelfTuningWorkManagerImpl$WorkAdapterImpl.run(SelfTunin
gWorkManagerImpl.java:528)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:209)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:178)
>
<12 Oct, 2012 12:34:40 PM IST> <Error> <oracle.soa.bpel.engine.dispatch> <BEA-00
0000> <Failed to handle dispatch message ... exception ORABPEL-05002
Message handle error.
error while attempting to process the message "com.collaxa.cube.engine.dispatch.
message.instance.CallbackDeliveryMessage"; the reported exception is: Error comm
itting transaction:; nested exception is: javax.transaction.xa.XAException: JDBC
driver does not support XA, hence cannot be a participant in two-phase commit.
To force this participation, set the GlobalTransactionsProtocol attribute to Log
gingLastResource (recommended) or EmulateTwoPhaseCommit for the Data Source = EB
SConnection
This error contained an exception thrown by the message handler.
Check the exception trace in the log (with logging level set to debug mode).
ORABPEL-05002
Message handle error.
error while attempting to process the message "com.collaxa.cube.engine.dispatch.
message.instance.CallbackDeliveryMessage"; the reported exception is: Error comm
itting transaction:; nested exception is: javax.transaction.xa.XAException: JDBC
driver does not support XA, hence cannot be a participant in two-phase commit.
To force this participation, set the GlobalTransactionsProtocol attribute to Log
gingLastResource (recommended) or EmulateTwoPhaseCommit for the Data Source = EB
SConnection
This error contained an exception thrown by the message handler.
Check the exception trace in the log (with logging level set to debug mode).
at com.collaxa.cube.engine.dispatch.DispatchHelper.handleMessage(Dispatc
hHelper.java:207)
at com.collaxa.cube.engine.dispatch.BaseDispatchTask.process(BaseDispatc
hTask.java:88)
at com.collaxa.cube.engine.dispatch.BaseDispatchTask.run(BaseDispatchTas
k.java:64)
at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExec
utor.java:886)
at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor
.java:908)
at java.lang.Thread.run(Thread.java:662)
>
Could any body help on this issue.It is little bit urgent for us to resolve.
Thanks in advance.Thanks Sudipto Desmukh,
The link is helpful me to resolve this issue.
Thanks,
Narasimha E -
Okay so I barely use the calling/phone app (the one that comes on it) on my iPhone but most of the calls I get are from random people who I do not know who have the wrong number asking for the same people! I block them all I can but they're not always the same number there's different numbers all the time it's extremely annoying and driving me crazy, the one person left a voice mail again asking for the same person so I called them back and they denied they ever called I kept telling them I got a voicemail from that number and they kept saying no one called from that number. I literally cannot take this anymore. I remember seeing somewhere when I was setting up my phone where I can set it so people cannot call you if they're not in your contacts list. Is there a way to do that? If there is could you please let me know and how to do so? I seriously really need this please. I have an iPhone 4s that's on ios 7.1.2 if that helps any. Thanks so much.
hi, this thread already deals with the issue:
How can I prevent getting calls from number that are not in my address book? -
CUPC 8.5.5 click to call from outlook 2007 challenges
Hello all,
The challenge I am having is that some ckient users are not recieving the abilty to click to call from there outlook address book. The actions button is greyed out (picture attached) from the address book.
version we are using currently is 8.5.5.19839. Windows 7 64 bit, Office 2007.
What shoul I be looking at for these users? I have the same set up with no issues. Any suggestions in the right direction would be helpful.
cheers
scottThere is an enhancement bug already filed for this feature. http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtd16602
Internally, I could see some activity on it during October 2011 as of recent.The action is still pending. For further details, yes TAC can be very much approached.
If the info helps, please rate the post.
GP. -
Video doesn't work when calling from Jabber to DX650
Hi,
I just added a DX650 to our CUCM 9.1.2. When I call from either Jabber to the DX650 or Lync to DX650, the video doesn't work and the call is audio only. The message i'm seeing on Jabber is something like "the other endpoint is not accepting video." Sorry i don't remember the exact message. Has anyone seen this issue before? Thanks!Lync is not standards based and has proprietary codecs for video. You will need a Expressway with the MS Interop key to get video both ways.
https://www.cisco.com/c/dam/en/us/td/docs/telepresence/infrastructure/vcs/config_guide/X8-2/Cisco-VCS-Microsoft-Lync-Deployment-Guide-X8-2.pdf -
Stolen iPhone 4 and follow-up Call from Apple
Hey guys,
My girlfriends iPhone 4 (32GB locked to Rogers) was stolen about a week and a half ago. She had Find My iPhone on it and we used it to lock and clear the phone right away, but since the phone was already turned off we were not able locate it. We get an e-mail the next day from the app saying that the lock and message were sent, which means the person who stole it probably turned it on. We still weren't able to locate the phone using the app so we just assumed they re-formatted the phone, cleared it, and logged out of iCloud. We thought end of story, we lost an iPhone, but there's nothing we could do. We go to an Apple store, tell them the phone was stolen and they proceed to use Find My iPhone to clear and lock the phone again (they say they weren't allowed to brick it and we weren't given the option to report it stolen).
Anyways, fast forward to a week later (night of Monday, Nov 5, 2012). We get a call from apple (call center 512-674-2000). The caller is Betty who works for Apple and she asks us if we have sold an iPhone on kijiji/eBay recently. We tell them that we've actually recently had the phone stolen and ask if someone's returning it. They say not quite, just that someone was tryign to contact apple with the iPhone's serial code. Unfortunately at this point the phone is very low on batter (<10%) so we ask if they can call back at another number. Betty says okay. We don't get a call back.
We call back the apple number that called us, but the call center is closed (it was around 8:15 EST). So we call the Apple Canada Hotline (we're from Toronto). The issue gets escalated to a manager and they're pretty much saying there's no notes on why the call was made. There definately has to be a reason for apple to call us asking if the phone was sold right? They tell us to call the number that called us earlier the following day to see if we can contact Betty who called us earlier. However, they do tell us that they ahve on their record that Betty called us, and prior to that, someone called with an issue about the stolen iPhone's serial code (we had not called in).
So we wait until the next day can call the 512 number. Pretty much we keep getting passed around with people telling us they can't do anything since there's no notes on the file and they can't redirect us to Betty.
My question is: There HAD to be a reason why they called us right? The phone was stolen at a friends house, where we thought we knew everybody. If we can get any information on who the original call was from maybe we can find out who stole the phone? Has anyone had a similar experience or does anyone have any advice on what to do? I'm sure apple knows something, but they are just not telling us. Sorry for the lengthy post, just wanted to get all the details out there! Thanks for any help!But if an issue is reported using the serial code of the stolen product, could they not tell me what number it was called from?
I understand that they can't do much, but I just wanted to know the original reason why Apple called us in the first place to ask whether we sold the iphone on kijiji or eBay recently. -
I have 3 different apple devices (iPod Touch, iPad and MacBook Pro) using the same Apple ID and would like to use FaceTime to call from one device to the other. Do I need a different Apple ID for one of the devices in order to do that?
I found this on a related question in the Community:
Yes you can do it. I do it with 4 different devices all using the same Apple ID.
You need to associate different email addresses for each device in order to use those email addresses as the "contact at" email address. The reason the calls are dropping on you now is that what you are trying to do is like calling yourself on your own phone.
You can also create new iCloud accounts on each device simply to use for FaceTime, but I'm guessing that the users of the other two devices have their own email addresses which will make this work for you quite easily.
Take a look at this for more information.
The seems to go against what Gail said and the issue you raised about buying dup apps was my first concern. If this other post is correct, how to I set a different "contact at" in the iPod Touch?
Goose -
How can i transfer a call from SIP 9971 to PBX system on CME router
hello everybody,
I have a critical problem about interaction of transfering feature between CME router and pbx panasonic system in some status. let me explain more detail about this issue..i have a SIP 9971(CP-9971) registered on CME at the one site and a voice gateway that is connect with PBX system through a E1 pri trunk connection at the other site. totally the integration between CME and PBX is ok and there is no problem in two direction, i mean i can call pbx system from cp-9971 and vise versa but when i call from a phone which is registered on PBX site to SIP 9971 which is registered on cisco CME call is connected,then when i try to transfer that call to another phone at PBX site, the session is open between two panasonic phones but no audio transmited in two direction. in addition every thing works fine about SCCP phones(transfer feature works fine). here is my configuration file. i hope someone could help me because i've searched a lot but no result help help help plz....
cme router 3845 configuration
VOIP-3845#show running-config
Building configuration...
Current configuration : 12657 bytes
! Last configuration change at 11:44:01 UTC Mon Oct 31 2011 by admin
! NVRAM config last updated at 11:44:02 UTC Mon Oct 31 2011 by admin
! NVRAM config last updated at 11:44:02 UTC Mon Oct 31 2011 by admin
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname VOIP-3845
boot-start-marker
boot-end-marker
no aaa new-model
clock calendar-valid
dot11 syslog
ip source-route
ip cef
no ipv6 cef
multilink bundle-name authenticated
voice-card 0
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
sip
bind control source-interface Loopback10
bind media source-interface Loopback10
registrar server
voice register global
mode cme
source-address 192.168.2.1 port 5060
max-dn 720
max-pool 262
load 9971 sip9971.9-1-1SR1.loads
authenticate register
authenticate realm cisco.com
tftp-path flash:
file text
create profile sync 0063544528862458
camera
video
voice register dn 1
number 500
voice register dn 2
number 600
voice register dn 3
number 700
name test
voice register template 1
softkeys idle Newcall Redial Cfwdall
softkeys connected Confrn Endcall Hold Trnsfer
voice register pool 1
id mac B8BE.BF23.5242
type 9971
number 1 dn 1
template 1
username test password test
camera
video
blf-speed-dial 4 600 label "test"
voice register pool 2
id mac B8BE.BF9C.5476
type 9971
number 1 dn 2
template 1
username bank password bank
camera
video
voice register pool 3
id mac B8BE.BF9C.51D4
type 9971
number 1 dn 3
template 1
username test1 password test1
camera
video
voice register pool 4
id mac B8BE.BF9C.4FA2
number 1 dn 1
camera
video
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-1576175886
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1576175886
revocation-check none
rsakeypair TP-self-signed-1576175886
crypto pki certificate chain TP-self-signed-1576175886
certificate self-signed 01
30820241 308201AA A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31353736 31373538 3836301E 170D3131 31303038 30393034
34365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 35373631
37353838 3630819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100D6EC 47BCDC3C 82F43FF3 23522678 2616868D 9910DCD2 E36016B3 D7B40DA7
53A6E339 4978D451 21F051BE B21F8AD5 86B952DC 1ECCE371 3E094B54 26A41E14
A3055C06 AE860756 425E5C50 E62B3287 631B1E87 9BAC2E39 2810E120 DA3BF823
947EA591 81CA5489 1B868239 E835EC7C 0AA7651A 22D6E47F 545EBEF3 A172C9A3
5A0D0203 010001A3 69306730 0F060355 1D130101 FF040530 030101FF 30140603
551D1104 0D300B82 09564F49 502D3338 3435301F 0603551D 23041830 1680146C
934AD072 99DDC600 ECD6F389 8F71E0C2 18EC2E30 1D060355 1D0E0416 04146C93
4AD07299 DDC600EC D6F3898F 71E0C218 EC2E300D 06092A86 4886F70D 01010405
00038181 000E82F6 5FBB847C 49226955 6F7DECE7 0B093513 D57C35D5 4CD22FA7
8144A080 B0D56C8D 86AF8156 0152443A A3FBE59F B1AEFFBC BEB43E09 35757BAD
4C06FC4A 0F3695E0 B00FBD30 4E8F36CE 7748F39C F9602650 7A1D2D48 DBC31237
AE3D63CE 593D31F5 62E4916F D20E30E8 30DC55C0 120FBD26 D2768DBC A67DDC34
5BDB66B1 E3
quit
license udi pid CISCO3845-MB sn FOC14421Q1Y
archive
log config
hidekeys
username admin privilege 15 secret 5 $1$Zf7j$P93opukmmEBIioVpjmHB3.
redundancy
interface Loopback10
ip address 192.168.2.1 255.255.255.0
interface Tunnel1
ip address 172.25.10.1 255.255.255.0
no ip redirects
ip nhrp map multicast dynamic
ip nhrp network-id 10
tunnel source GigabitEthernet0/1.1
tunnel mode gre multipoint
tunnel key 100
interface Tunnel2
ip address 172.25.11.1 255.255.255.0
no ip redirects
ip nhrp map multicast dynamic
ip nhrp network-id 20
tunnel source GigabitEthernet0/1.2
tunnel mode gre multipoint
interface Tunnel14
ip address 192.168.13.129 255.255.255.252
tunnel source GigabitEthernet0/1.1
tunnel destination 10.2.68.25
interface Tunnel18
ip address 192.168.13.137 255.255.255.252
tunnel source GigabitEthernet0/1.1
tunnel destination 10.9.160.236
interface GigabitEthernet0/0
no ip address
shutdown
duplex auto
speed auto
media-type rj45
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
media-type rj45
interface GigabitEthernet0/1.1
encapsulation dot1Q 10
ip address 10.9.160.25 255.255.255.0
interface GigabitEthernet0/1.2
encapsulation dot1Q 50
ip address 10.10.9.25 255.255.255.0
router eigrp 202
network 172.25.11.0 0.0.0.255
network 192.168.2.0 0.0.0.15
redistribute static route-map MYMAP1
router eigrp 201
network 172.25.10.0 0.0.0.255
network 192.168.2.0 0.0.0.15
redistribute static route-map MYMAP1
ip forward-protocol nd
ip http server
ip http secure-server
ip http path flash:/gui
ip route 10.2.68.0 255.255.255.0 10.9.160.1
ip route 10.10.0.0 255.255.0.0 10.10.9.1
ip route 10.64.164.30 255.255.255.255 10.9.160.1
ip route 192.168.14.0 255.255.255.0 192.168.13.130
ip route 192.168.17.0 255.255.255.0 Tunnel18
ip access-list standard REDIS1
permit 192.168.14.0
permit 192.168.17.0
route-map MYMAP1 permit 10
match ip address REDIS1
snmp-server community test RO
tftp-server flash:term11.default.loads
tftp-server flash:dkern9971.100609R2-9-0-3.sebn
tftp-server flash:kern9971.9-0-3.sebn
tftp-server flash:rootfs9971.9-0-3.sebn
tftp-server flash:sboot9971.111909R1-9-0-3.sebn
tftp-server flash:sip9971.9-0-3.loads
tftp-server flash:skern9971.022809R2-9-0-3.sebn
tftp-server flash:sccp11.9-0-2sr1s
tftp-server flash:SCCP11.9-1-1SR1S.loads
tftp-server flash:apps11.9-1-1TH1-16.sbn
tftp-server flash:cnu11.9-1-1TH1-16.sbn
tftp-server flash:cvm11sccp.9-1-1TH1-16.sbn
tftp-server flash:dsp11.9-1-1TH1-16.sbn
tftp-server flash:jar11sccp.9-1-1TH1-16.sbn
tftp-server flash:term06.default.loads
tftp-server flash:sip9971.9-1-1SR1.loads
tftp-server system:cme/sipphone
tftp-server flash:Desktops/320x212x12/NantucketFlowers.png
tftp-server flash:Desktops/320x212x12/TN-CampusNight.png
tftp-server flash:Desktops/320x212x12/TN-CiscoFountain.png
tftp-server flash:Desktops/320x212x12/TN-Fountain.png
tftp-server flash:Desktops/320x212x12/TN-MorroRock.png
tftp-server flash:Desktops/320x212x12/TN-NantucketFlowers.png
tftp-server flash:Desktops/320x212x12/Fountain.png
tftp-server flash:Desktops/320x212x12/CiscoLogo.png
tftp-server flash:Desktops/320x212x12/TN-CiscoLogo.png
tftp-server flash:Desktops/320x212x12/List.xml
tftp-server flash:Desktops/320x216x16/List.xml
tftp-server flash:Desktops/320x212x16/List.xml
tftp-server flash:gui/admin_user.html
tftp-server flash:gui/admin_user.js
tftp-server flash:gui/CiscoLogo.gif
tftp-server flash:gui/Delete.gif
tftp-server flash:gui/dom.js
tftp-server flash:gui/downarrow.gif
tftp-server flash:gui/ephone_admin.html
tftp-server flash:gui/logohome.gif
tftp-server flash:gui/normal_user.html
tftp-server flash:gui/normal_user.js
tftp-server flash:gui/Plus.gif
tftp-server flash:gui/sxiconad.gif
tftp-server flash:gui/Tab.gif
tftp-server flash:gui/telephony_service.html
tftp-server flash:gui/uparrow.gif
tftp-server flash:gui/xml-test.html
tftp-server flash:gui/xml.template
tftp-server flash:ringtones/Analog1.raw
tftp-server flash:ringtones/Analog2.raw
tftp-server flash:ringtones/AreYouThere.raw
tftp-server flash:ringtones/AreYouThereF.raw
tftp-server flash:ringtones/Bass.raw
tftp-server flash:ringtones/CallBack.raw
tftp-server flash:ringtones/Chime.raw
tftp-server flash:ringtones/Classic1.raw
tftp-server flash:ringtones/Classic2.raw
tftp-server flash:ringtones/ClockShop.raw
tftp-server flash:ringtones/DistinctiveRingList.xml
tftp-server flash:ringtones/Drums1.raw
tftp-server flash:ringtones/Drums2.raw
tftp-server flash:ringtones/FilmScore.raw
tftp-server flash:ringtones/HarpSynth.raw
tftp-server flash:ringtones/Jamaica.raw
tftp-server flash:ringtones/KotoEffect.raw
tftp-server flash:ringtones/MusicBox.raw
tftp-server flash:ringtones/Piano1.raw
tftp-server flash:ringtones/Piano2.raw
tftp-server flash:ringtones/Pop.raw
tftp-server flash:ringtones/Pulse1.raw
tftp-server flash:ringtones/Ring1.raw
tftp-server flash:ringtones/Ring2.raw
tftp-server flash:ringtones/Ring3.raw
tftp-server flash:ringtones/Ring4.raw
tftp-server flash:ringtones/Ring5.raw
tftp-server flash:ringtones/Ring6.raw
tftp-server flash:ringtones/Ring7.raw
tftp-server flash:ringtones/RingList.xml
tftp-server flash:ringtones/Sax1.raw
tftp-server flash:ringtones/Sax2.raw
tftp-server flash:ringtones/Vibe.raw
tftp-server flash:APPS-1.2.1.SBN
tftp-server flash:SYS-1.2.1.SBN
tftp-server flash:GUI-1.2.1.SBN
tftp-server flash:CP7921G-1.2.1.LOADS
tftp-server flash:TNUX-1.2.1.SBN
tftp-server flash:TNUXR-1.2.1.SBN
tftp-server flash:WLAN-1.2.1.SBN
tftp-server flash:apps37sccp.1-2-1-0.bin
tftp-server flash:APPSH-1.3.1.SBN
tftp-server flash:GUIH-1.3.1.SBN
tftp-server flash:CP7925G-1.3.1.LOADS
tftp-server flash:SYSH-1.3.1.SBN
tftp-server flash:TNUXH-1.3.1.SBN
tftp-server flash:WLANH-1.3.1.SBN
tftp-server flash:SCCP11.9-2-1S.loads
tftp-server flash:Desktops/320x212x12/CampusNight.png
tftp-server flash:Desktops/320x212x12/CiscoFountain.png
tftp-server flash:Desktops/320x212x12/MorroRock.png
tftp-server flash:skern9971.022809R2-9-2-1.sebn
tftp-server flash:sip9971.9-2-1.loads
tftp-server flash:sboot9971.031610R1-9-2-1.sebn
tftp-server flash:rootfs9971.9-2-1.sebn
tftp-server flash:dkern9971.100609R2-9-2-1.sebn
tftp-server flash:kern9971.9-2-1.sebn
tftp-server flash:United_States/g4-tones.xml
tftp-server flash:English_United_States/gd-sip.jar
tftp-server flash:sboot9971.031610R1-9-1-1SR1.sebn alias sboot9971.031610R1-9-1-1SR1.sebn
tftp-server flash:rootfs9971.9-1-1SR1.sebn alias rootfs9971.9-1-1SR1.sebn
tftp-server flash:kern9971.9-1-1SR1.sebn alias kern9971.9-1-1SR1.sebn
tftp-server flash:dkern9971.100609R2-9-1-1SR1.sebn alias dkern9971.100609R2-9-1-1SR1.sebn
tftp-server flash:skern9971.022809R2-9-1-1SR1.sebn alias skern9971.022809R2-9-1-1SR1.sebn
control-plane
mgcp profile default
dial-peer voice 1 voip
description connection-trough-PBX
destination-pattern 0....
session target ipv4:192.168.13.130
dtmf-relay h245-alphanumeric
no vad
dial-peer voice 100 voip
description K
destination-pattern 9T
session target ipv4:192.168.13.130
dtmf-relay h245-alphanumeric
no vad
dial-peer voice 5 voip
shutdown
destination-pattern *3709
session protocol sipv2
session target ipv4:192.168.13.130
session transport tcp
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
dial-peer voice 2 pots
incoming called-number .
dial-peer voice 10 voip
gatekeeper
shutdown
telephony-service
em logout 0:0 0:0 0:0
max-ephones 262
max-dn 400
ip source-address 192.168.2.1 port 2000
load 7911 SCCP11.9-2-1S
max-conferences 12 gain -6
web admin system name admin secret 5 $1$IKnn$tyKyuBcGqXFl6nhxCSu.z0
dn-webedit
time-webedit
transfer-system full-consult
transfer-pattern .T
create cnf-files version-stamp 7960 Oct 29 2011 12:39:25
ephone-template 1
softkeys connected Confrn Endcall Trnsfer Hold
keep-conference endcall
ephone-dn 1 dual-line
number 200
label test
name test
ephone-dn 2 dual-line
number 300
label Sepahbod
name Sepahbod
ephone-dn 4 dual-line
number 666
ephone-dn 5 dual-line
number 660
ephone-dn 6 dual-line
number 670
ephone-dn 7 dual-line
number 770
ephone-dn 8 dual-line
number 770
ephone-dn 9 dual-line
number 999
ephone 1
device-security-mode none
mac-address 18EF.639F.BCB0
keep-conference endcall
button 1:1
ephone 2
device-security-mode none
mac-address 0025.8418.B017
ephone-template 1
keep-conference endcall
button 1:2
ephone 3
device-security-mode none
mac-address F04D.A243.3154
keep-conference endcall
button 1:4
ephone 4
device-security-mode none
mac-address 6CF0.496A.69E9
button 1:4
ephone 5
device-security-mode none
mac-address 0015.E987.345F
keep-conference endcall
button 1:5
ephone 6
device-security-mode none
mac-address 0024.1DEA.614A
keep-conference endcall
button 1:6
ephone 9
device-security-mode none
mac-address 001D.7D4D.4DCB
button 1:9
line con 0
line aux 0
line vty 0 4
login local
transport input telnet
scheduler allocate 20000 1000
end
and Voice Gateway connected two PBX system configuration
Current configuration : 3486 bytes
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Voice-GW
boot-start-marker
boot-end-marker
card type e1 0 2
no aaa new-model
network-clock-participate wic 2
dot11 syslog
ip source-route
ip cef
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-net5
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
h323
voice-card 0
crypto pki token default removal timeout 0
license udi pid CISCO2811 sn FHK1352F0E9
username admin privilege 15 secret 5 $1$O6AN$1kvvqiLdIl3/ZTHoyYRy0/
redundancy
controller E1 0/2/0
framing NO-CRC4
pri-group timeslots 1-31
controller E1 0/2/1
interface Tunnel14
ip address 192.168.13.130 255.255.255.252
tunnel source FastEthernet0/1
tunnel destination 10.9.160.25
interface Tunnel17
ip address 192.168.13.134 255.255.255.252
tunnel source FastEthernet0/1
tunnel destination 10.9.160.25
interface FastEthernet0/0
ip address 192.168.14.252 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
ip address 10.2.68.25 255.255.255.0
duplex auto
speed auto
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn overlap-receiving
isdn incoming-voice voice
no cdp enable
router eigrp 201
network 172.25.10.0 0.0.0.255
network 192.168.14.0
ip forward-protocol nd
no ip http server
no ip http secure-server
ip route 10.9.160.0 255.255.255.0 10.2.68.1
ip route 10.128.0.69 255.255.255.255 Tunnel14
ip route 192.168.2.1 255.255.255.255 192.168.13.129
ip route 192.168.17.0 255.255.255.0 Tunnel14
tftp-server flash:SCCP11.9-2-1S.loads
tftp-server flash:jar11sccp.9-2-1TH1-13.sbn
tftp-server flash:dsp11.9-2-1TH1-13.sbn
tftp-server flash:cvm11sccp.9-2-1TH1-13.sbn
tftp-server flash:cnu11.9-2-1TH1-13.sbn
tftp-server flash:apps11.9-2-1TH1-13.sbn
control-plane
voice-port 0/0/0
caller-id enable
voice-port 0/0/1
voice-port 0/0/2
supervisory disconnect dualtone mid-call
dial-type pulse
disc_pi_off
output attenuation 1
echo-cancel coverage 32
timeouts call-disconnect 5
timeouts wait-release 1
timing hookflash-out 50
timing sup-disconnect 50
connection plar 600
caller-id enable
voice-port 0/0/3
caller-id enable
voice-port 0/2/0:15
mgcp profile default
dial-peer voice 1 pots
description connection-to-PBX
destination-pattern 0....
direct-inward-dial
port 0/2/0:15
forward-digits 4
dial-peer voice 10 voip
destination-pattern ...
session target ipv4:192.168.13.129
dtmf-relay h245-alphanumeric
no vad
dial-peer voice 20 pots
description FXO-K
destination-pattern 9T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
direct-inward-dial
port 0/0/2
prefix 9
dial-peer voice 30 pots
description FXO-K2
destination-pattern 9T
direct-inward-dial
port 0/0/1
prefix 9
telephony-service
max-ephones 20
max-dn 100
ip source-address 192.168.14.252 port 2000
cnf-file location flash:
load 7911 term11.default.loads
max-conferences 8 gain -6
transfer-system full-consult
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-dn 1
number 770
line con 0
line aux 0
line 1/0 1/15
line vty 0 4
login local
transport input telnet
scheduler allocate 20000 1000
endHaving looked at your spreadsheet I see you're failing H323 transfers back to your ISDN system, but only under certain circumstances. Quite why, I'm not sure, possibly because you haven't codec defined on your H323 dial peers. or it could be something else
I think you may be able to work around the problem by adding
" supplementary-service h450.12 " under voice service voip on your CME router as a quick fix.
reference
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmetrans.html#wpxref44614
worth a try
Adam -
Random call to 911 and other issues
(Yes, mods I did search the boards for this issue and I didn't see it. Most people want to know how to call 911. I want to know how to stop my phone from doing it by itself!)
Hello, I'm a brand new Verizon customer and was so excited to switch carriers and pick up a new smart phone!
Now I'm not so excited to be a verizon customer with a new smart phone.
Last night I went to use my Samsung charge and of course, it was locked up (again). All the icons were inoperable and the screen was frozen. So, for at least the 5th time of the day, I had to remove and replace the battery and wait for the phone to reboot.
Within a few minutes, I received a call from a number I didn't recognize and the man on the other end identified himself as a county sheriff. He said they received a 911 hang up and it came from my number! I was so confused because I'd done no such thing. He said it was the departments policy to followup and make sure I was okay. I tried to assure him that I was okay, that my phone had been sitting on the table and I had NOT called 911. He then insisted that I give him my address so he could come over to make sure I was okay. Then I got scared....Really really scared since my husband was not home and I was alone and the call seemed so bizarre. I refused to give him any more information, told him I didn't believe him and hung up. I checked my call log and it didn't show any call to 911.
I was freaked out, so I called my city's non emergency police line and and city officer called me back. I told him what happened and he decided to call the number and call me back. A few minutes later he did.
It turns out that it really WAS a county sheriff and apparently my phone had made a random call to 911 and pinged a tower on the other end of the valley!
I've learned to live with pulling and replacing the battery multiple times per day. I've learned to live with the lack of battery life. I've learned to live with not having workable bluetooth.
After owning this phone for about 4 months, I already hated it for all the glitches and issues it has but now I am very very very alarmed that my phone makes random calls to 911 and hangs up !! You can be issued a citation and fined ! This I will not live with!!
Verizon, is this the phone causing this? Is it something in your network? How do I stop this from happening again?? This was extremely stressful for me and I can't have it continue to happen!Hi GoDaisy,
I can definitely understand your frustration regarding the scenario with the sheriff's office contacting you about a 911 call! I have completed some troubleshooting with the Charge, as I use this device myself. With this phone, if you create an additional lock with either a passcode or a pattern that has to be entered, there is a button on the bottom of the phone that says "Emergency Call." If this button is pressed, a 911 call, or any number that has been entered as the emergency number, is able to be dialed.
I see that you mentioned that you were in the middle of resetting the device because the screen was frozen. Do you recall if the screen was frozen on the lock screen when this happened? If so, you may have inadvertently pressed the button for the emergency call.
If you do not have a lock pattern or a pin code set up for the device, the standard lock (where you connect the puzzle piece) is the default. This screen does not have an option for an emergency call. If you have the additional lock screen set up on the device, you could remove it and set up a different number for the emergency call.
You also have the option of downloading a free application from the Android Market called "ICE," or "In Case of Emergency." You can set up this application with your own personal preferences. Press the Market icon and use ICE as a keyword search.
Below I have provided the steps on how to remove the lock code/pattern for you, if needed.
Removing the lock code/pattern:
Press "Applications" icon from main screen
Press "Settings"
Press "Location & Security"
Press "Change Screen Lock"
Confirm your current unlock code or pattern by entering it
Press "None"
To set up an emergency call, you can simply program the number as a contact, and then save the number as a speed dial.
Assigning Speed Dials
1. From the Home screen, touch Contacts.
2. Press the Menu Key, then touch More-> Speed dial.
3. A list of speed dials displays.Touch a speed dial, then touch a contact to assign the contact to the speed dial.
Please let us know if you are still having issues with your phone locking up and having to re-boot it by removing the battery. Do you notice any pattern about when this happens? Are you performing any specific function when the screen freezes?
Additionally, I want to clarify that any calls to 911 are not listed in your call records online or on your bill due to the fact that these calls are free. Your statement only shows billable calls, so this is the reason you do not see the call in the call log.
I hope this information is helpful for you. Please post back with any findings or results.
Thanks very much,
Maybe you are looking for
-
My brother-in-law recently passed away. My sister gave his MacBook Pro to my niece. When she opens and starts the laptop, it shows my brother-in-laws name. Is there a way to change his name to her name without formatting the device and starting over?
-
HT204088 I have put in two iTunes gift cards and a visa pre-paid giftcard
the visa is out and i cant change my billing info. I cannot re-redeem my iTunes cards and i cleared my billing numbers and that hasnt worked. What do I do?
-
Refurbished iBook...no install disks???
My husband just bought a refurbished 12-inch iBook. Of course, it has all of the standard software loaded on it, but he tells me that he no CDs or any materials with the iBook. Should he have? I'm thinking, so what happens when he has a huge meltdown
-
Will PC and Mac be able to get together this Valentine's?
Hello! My flatmate has an Apple eMac and I have a Windows 98 Dell Dimension XPS R450. We have just signed up to NTL Broadband and have the modem connected to the Windows 98 PC. Broadband is running fine on the PC. One of us is a student and the other
-
Front Row won't display station information of radio streams.
Hi, I love to use Front Row to listen to internet radio stations. While iTunes displays the station information correctly (mostly artist and title) Front Row only shows blank. Does anybody know if it's possible to activate station information in Fron