Date and time configuration

Can configure the date and time

Hi NVN1979,
Welcome to the Support Communities!
Below is the basic troubleshooting guide for Apple TV.
Restarting the modem and the Apple TV is a good first step.
Apple TV: Basic troubleshooting
http://support.apple.com/kb/ht1551
Reset Apple TV by unplugging it from the power outlet, waiting about five seconds, then plugging it in again.
Power off your TV, wait five seconds, then power it back on.
Apple TV (2nd and 3rd generation): Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS4546
Ensure that Apple TV is within range of your Wi-Fi router or base station.
Confirm that your Wi-Fi router and cable/DSL modem are connected to power and turned on.
Make sure other devices (computers, iPhone, iPad, for example) are able to connect to the Wi-Fi network and access the Internet.
Check your Wi-Fi network settings on Apple TV:
Select Settings > General > Network > Wi-Fi and press the center button on the remote to display nearby networks.
Choose your Wi-Fi network from the list.
If your Wi-Fi network uses a password, make sure you are entering it correctly.
Restart your Apple TV by selecting Settings > General > Restart.
Try restarting your Wi-Fi router or modem by turning it off and then on again.
If possible, connect an Ethernet cable and verify your Internet connection. If you can connect to the Internet using an Ethernet connection, verify that your Apple TV is using the latest software by selecting Settings > General > Software Update. If your Apple TV can be updated, install the update and then try the steps again.
Apple TV (2nd and 3rd generation): Restoring your Apple TV
http://support.apple.com/kb/ht4367
On Apple TV, choose Settings > General > Reset, and then click Restore.
Your Apple TV will restore to its factory settings, and will also download and install the latest Apple TV software update. This process may take some time. Do not disconnect your Apple TV's power cable during the restore process.
If you cannot use this process, and you have a micro USB cable, try the steps in the next section.
If your Apple TV (2nd and 3rd generation) still does not respond
If have a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
Disconnect the power and HDMI cables from Apple TV. Note: If you do not disconnect the power cable before connecting the micro USB cable, you will not see Apple TV in the iTunes Source list.
Connect one end of a micro USB cable to the back of your Apple TV, and the other end to one of your computer's USB ports.
Apple TV (3rd generation) only: Reconnect the power cable to your Apple TV.
Open iTunes on your computer.
Select your Apple TV in the Source list, and then click Restore.
Your Apple TV will restore to its factory settings, and will also download and install the latest Apple TV software update. This process may take some time.
Do not disconnect any cables from the Apple TV until the restore process is completed.
I hope this information helps ....
Have a great day!
- Judy

Similar Messages

WLC date and time configuration

Hi, I have a problem with a 4402 Wireless LAN Controller running 7.0.116.0 versión. The equipment is working fine, but after a hard reset i lost date and time
configuration.No other configuration is affected, only date and time. What can be the cause of this?

Hi Leo, mabuti naman po ako. Ikaw kumusta? You can speak tagalog pala. << OT.
WLC don't have NTP configured because they don't have NTP server. Anyway, I must agree with you in terms of unstable power source here in Philippines, but in this case, the client datacenter do have redundant UPS standing-by incase power interruption occurs. Actually, my client have 2x 5508 sitting side by side. The other one is working properly because we tried them to switch off and then unplugged the power cord from power source. When we plugged it again and they boot up, one WLC retains its clock and date but the other one reverts to January 1, 2000.
I think we better request for an RMA for this unit.

Work Status Report Date and Time Setting

Hi all
We are running BPC10 on servers configured with Central European Time which is currently 2 hours ahead of GMT allowing for Daylight Savings Time.
From what i can see in BPC10 date and times are now stored in GMT (Zulu time) in the Audit activity tables so when a user updates the work status at say 11:00AM local CET time then a value of 09:00AM GMT is stored in the Audit Activity Header table.
We have a report in excel that uses the EVLCK formula and will return the correct value of 11:00 am however if we run the Work Status Audit report on the Planning and Consolidation home page with user preferences set to Central European Time +1 then the time is displayed as 10:00am suggesting that daylight savings time is not accounted for. We need to set the time to Eastern European time +2 hours to display the correct figure.
Can anyone explain why this happens? Has DST been overlooked?
Rgds
Alan

Hi Alan,
probably it's a bug, I think it's better you open an OSS message to SAP.
Regards
Roberto

Can't remotely connect to my server if I automatically set date and time

Hello.
I have configured my OS X 10.6.2 server and am able to remotely manage it.
The only ports I have opened on my router is for Mail and VPN services.
Things work perfectly because I can connect using VPN to iChat, iCal, Address Book, Server Admin, Workgroup Manager, AFP, FTP and such.
The problem is that on my laptop from home, or wherever, if its time is set to update automatically from an NTP server (I have tried with Apple's as well as my server for the NTP Servers) then I cannot connect to my server at all...
The moment I turn off the auto date and time and reconnect to the office's VPN, I am able to use Server Admin, AFP, FTP, Workgroup Manager, Screen Sharing, etc, etc, etc.
It's utterly frustrating because I have to open system preferences, disable the automatic date and time update, connect to the VPN and do stuff on the server. Then I have to disconnect from VPN and re enable the auto date and time.
Could someone explain why this is happening and any possible solutions I might be able to try?
Thanks in advance,
Felipe.

OK, after some testing things seem to be working now.
I opened the NTP port for my server (So I don't have to be on VPN to update the time)....But regardless of that, Server admin and my corporate site work fine.
Here is my problem, I don't understand why it's working now when 30 minutes ago I was having trouble connecting to my server regardless of what NTP Server I used.
The only service I can't access is Workgroup Manager, but I don't know if that is supposed to be accessible only locally (though it doesn't matter since I can screen share but I would still like to know).
Thanks in advance,
Felipe.

Microsoft Date and Time Picker Control 6.0 (SP6) errors

One of our functioning VBA projects in Outlook 2010, running under Windows 7 Professional (64-bit), unexpectedly stopped functioning a few months ago. When running the VBA macro we started receiving the compile error message:
"Object library invalid or contains references to object definitions that could not be found"
PROBLEM FORM CONTROL: The message was extremely frustrating because it gave no detailed indication of the source of the problem. With a little research, however, we found that the
Microsoft Date and Time Picker Control 6.0 (SP6), on a userform accessed by the macro, was generating the error. A number of older articles, such as the one included below, indicated that we needed
to re-register the MSCOMCT2.OCX form control, which we did successfully (as did the original author in his question link below). Unfortunately, as the original author found, simply re-registering the form control did not resolve the problem.
UNRESOLVED QUESTIONS:
1. Does anyone know why this functioning control would unexpectedly cease to function?
2. Can anyone help us restore the functionality of the 'Microsoft Date and Time Picker Control 6.0 (SP6)'?
3. How come the form control is listed in the object library, is available in the 'Additional Controls' dialog, and can be inserted into a form, without any indication that it is broken?
SUPPORT ENGINEER RUN-AROUND: Another frustration is that a responding support engineer, in the prior article, keeps referring the author back to this forum, yet the question is apparently never answered back here in
the TechNet forum (which ironically refers us back to the original article in the other forum - a game of musical chairs!).
We suspect that the solution to this problem may be similar to resolving this issue for other similar form controls in other Office 2010 application, not just Outlook. After several years, and a myriad questions on the internet regarding
this exact subject, is there someone who can definitively resolve this issue with this control?
Thank you for any help.
LINK TO THE ORIGINAL UNANSWERED QUESTION (i.e., regarding the MSCOMCT2.OCX control and reference back to this forum):
http://answers.microsoft.com/en-us/office/forum/office_2013_release-excel/ms-date-and-time-picker-contol-60-sp-6-w-excel/9b0cc596-5e13-48bc-b03e-13dbfd1c7f9d

Hi,
Would you like to tell me your Excel version number (Go to Account>About Excel). I tested in my version :15.0.4569.1504 and the Date and Time Picker Control 6.0 still could be used.
Then,>> My PC is 64 bit. I believe my version of Office is also 64 bit.<< Office 2013 32 bit also could be installed in 64bit operation system. We could check it with Account>About Excel.
Next, as you said >>After I exited 'Design Mode,' it started working again. I tested it, along with my 'Clear Form' button multiple times. It seemed to be working fine. I closed the document and reopened it. Enabled Macros.
When I tried to use it after reopen, it doesn't work again.<<
I recommend we recreate a new blank Excel file and insert the Date and Time Picker Control 6.0 to test.
If it still does not work well, please try to reinstall and re-registry it. Follow the link:
https://social.msdn.microsoft.com/Forums/office/en-US/36f83f24-cd76-4f8e-aa7b-5f166666e7d3/excel-2013-popup-calendar
https://social.msdn.microsoft.com/Forums/en-US/91cf3127-70fe-4726-8a27-31b8964430c5/registering-mscomct2ocx-in-64-bit-windows-7?forum=sbappdev
If it works well, I suppose this issue is related to macros. I recommend you post the question to MSDN forum to debug them:
https://social.msdn.microsoft.com/Forums/office/en-US/home?forum=exceldev
Regards,
George Zhao
TechNet Community Support
It's recommended to download and install
Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
programs.

Cisco SPA525g2 Date and time Not Synced with the PBX server

Hello,
We have a couple of SPA525g2 phone connected and registered to our PBX server. We were able to configure 3 extensions on different lines of the phone. However, at times we were encountering issues with the other lines configured on the phone. There are times wherein 1 extension configured on the phone is having one way audio issue, but the other extensions configured on the same phone is working fine. and we have to reboot/reset the phone several times for all the extesions configured on the phone to work.
Also, whenever we reset the phone, the date and time will be way way behind the current date and time, eventhough we have already set the correct date and time before we reset the phone.
How can we resolve the one way audio issue on 1 or 2 extensions of the phone, while the other extensions configured to it is working fine?
How can we make the phone sync the date and time with the PBx server?
Any input and help regarding this issue is greatly appreciated...
Btw, date and time issue not sync with the PBX server is just happening on SPA525g2, we have other phones like SPA303, SPA504, and SPA232D/SPA302D. All other phones' date and time is in sync with the server even though we reset them except SPA525g2.
Thank you very much,

PeterMacSF,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://forums.novell.com)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://forums.novell.com/faq.php
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://forums.novell.com/

Date and Time Sync at boot for Active Directory/Open Directory Authenticati

All the macs in my school district are set to automatically sync their time with a network time server. They do not do this unless the system preference is opened. This poses a problem as all our users must authenticate against an Active Directory and an Open Directory server. If the time is out of sync they can not login, and therefore can not fix the time. I must then login in with a local admin account set the time and then the network account can login. I have tried using direct IP addresses for the NTP server. That doesn't work either. I have adjusted the tolerance of the AD server to accept a large discrepancy in time (did not work). Set the users to be mobile accounst (local home folders), did not work. The only fix will be to ensure that the time does sync at boot, before login. Is there a way to force the computer to sync at boot to a given NTP server, prior to the login window appearing?

I have come up with my own solution for this issue. It is a two part solution. We found that the computers are experiencing time drift and that after they get out of sync by 5 minutes they can no longer login. One would think that the setting in the Date and Time system preference to automatically synchronize the time would take care of this. That however is not the case that check mark does not affect the ntp service at all. It merely eliminates the need to click a button when entering the system preference. How did we discover this? well that is part of the solution. We used webmin (http://www.webmin.com) to look at the ntp configuration. No matter what changes we made with the Date & Time preferences nothing changed in the system ntp settings. So on to the solution: Install webmin, and configure the ntp protocol manually to sync at your desired interval (I did hourly). This stops time drift. Next create a startup item and associated plist to force time sync at boot (be sure to loop it as different machines initialize their network cards slower). I have made ours available for download (http://www.manheimcentral.org/~getzt/netTime.zip). I hope this helps others. We have found that this works fairly well.

The setting date and time is not working

Bought an apple TV, installed it as per instruction, connected to my internet but the seting date and time is not occuring and the activation cannot occur either. Spent 1 hr on the phone with Apple support staff - they told me it may be a router blockage and to contact my internet provider. contacted internet provider , they tell me everything is working from their end so must be the apple TV device. I was told this was easy techonology and that I would not have issues - I have spent 3 hrs on this and truly frustrated as its not working . any suggestions would help!

That would be a network issue as you were initially advised. When the date and time can not be set it means it is having trouble connecting to the network.
Make sure router is up to date, reboot router and ATV. Make sure location is set correctly via ATV and also DNS (settings - general - network - configure DNS - automatic)
Make sure your router allows access over port 123.
Failing that try a restore on the unit

Microsoft Date and Time Picker Control 6.0 - Need help!

I am working on a form in Office 365 Excel 2013 that uses the Microsoft Date and Time Picker Control 6.0. When I set the form up last week, this Active X control was working perfectly. The weekend goes by...and now it's not working at all?
My PC is 64 bit. I believe my version of Office is also 64 bit. When I researched this issue online, I found lots of people who indicated that this control was missing in their development kit. It was and has always been available in mine
(i.e. I didn't have to load an MSCOMCT2 file). Further, this control WAS WORKING when I created it last week. Now it is not, even though no changes have been made to it. I can place the control on the sheet and even set properties for it.
But once I click out of Design Mode, it is not functioning. It doesn't open or respond to any clicks on it.
Can anyone help me identify a reason why it may have suddenly stopped working? I don't think it is macro-related because I have a 'Clear Form' button on the same page and it works just fine.
UPDATE: I've noticed something else peculiar but relevant. My office 365 just did some updates. When updates were completed, it auto-reopened my file. I noticed that the Date/Time Picker button looked funny (really pixelated).
So I hit 'Design Mode' and resized it. After I exited 'Design Mode,' it started working again. I tested it, along with my 'Clear Form' button multiple times. It seemed to be working fine. I closed the document and reopened it.
Enabled Macros. When I tried to use it after reopen, it doesn't work again. Won't respond to ANY attempts to click on it. I can click on 'Design Mode' and it sees the control, edits properties, etc. But when you click out of 'Design Mode,'
it's a dead button again. I also went to someone else's desk to test this form. Same problem. Date/Time picker button doesn't work, even after enabling macros. The Clear Form Button has no problems though.
Thanks!

Hi,
Would you like to tell me your Excel version number (Go to Account>About Excel). I tested in my version :15.0.4569.1504 and the Date and Time Picker Control 6.0 still could be used.
Then,>> My PC is 64 bit. I believe my version of Office is also 64 bit.<< Office 2013 32 bit also could be installed in 64bit operation system. We could check it with Account>About Excel.
Next, as you said >>After I exited 'Design Mode,' it started working again. I tested it, along with my 'Clear Form' button multiple times. It seemed to be working fine. I closed the document and reopened it. Enabled Macros.
When I tried to use it after reopen, it doesn't work again.<<
I recommend we recreate a new blank Excel file and insert the Date and Time Picker Control 6.0 to test.
If it still does not work well, please try to reinstall and re-registry it. Follow the link:
https://social.msdn.microsoft.com/Forums/office/en-US/36f83f24-cd76-4f8e-aa7b-5f166666e7d3/excel-2013-popup-calendar
https://social.msdn.microsoft.com/Forums/en-US/91cf3127-70fe-4726-8a27-31b8964430c5/registering-mscomct2ocx-in-64-bit-windows-7?forum=sbappdev
If it works well, I suppose this issue is related to macros. I recommend you post the question to MSDN forum to debug them:
https://social.msdn.microsoft.com/Forums/office/en-US/home?forum=exceldev
Regards,
George Zhao
TechNet Community Support
It's recommended to download and install
Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
programs.

The date and time in Hebrew?

hi
i need to show the current date and time. i see that i can
use :
var now:Date = new Date();
trace(now);
the result is:
Wed Jun 11 16:47:18 GMT+0300 2008
but what if i need it in Hebrew?
and how do i lose the "GMT+0300 "?
and maybe more: how can i format the date and time myself?
best regards
ron

This doc should help you set the time:
http://www.cisco.com/en/US/docs/wireless/access_point/12.3_7_JA/configuration/guide/s37adm.html#wp1036858

Snow Leopard users: Turn off automatic date and time in System Preferences immediately

http://arstechnica.com/apple/2014/12/apple-automatically-patches-macs-to-fix-sev ere-ntp-security-flaw/
When exploited, the NTP flaw can cause buffer overflows that allow remote attackers to execute code on your system.
What this means is that, if you allow date and time to be set automatically by outside servers, you risk having your computer taken over.
This is a critical issue, it's being exploited as we speak, and Apple has not provided the update to Snow Leopard users, only to 10.8/Mountain Lion and above. I strongly doubt Apple will ever get around to issuing an update for Snow Leopard, or they would have already. Chances of that happening are close to zero

To me 10.6.8 is still the best OS X Apple ever released and I patched my system just like the shellshock back in September. It's really easy if you have some basic shell skills and XCODE installed,
Here is what I did, it may save you some time:
open the terminal app
1) Download the source code, apply the patch (I got the source code links from the ntp site)
cd ~
mkdir ntpd-fix
cd ntpd-fix
curl http://www.eecis.udel.edu/~ntp/ntp_spool/ntp4/ntp-4.2/ntp-4.2.8.tar.gz | tar zxf -
2) Patch and compile the ntp source code
cd ntp-4.2.8/ntpd
curl http://bugs.ntp.org/attachment.cgi?id=1165 | patch -p1
cd ..
./configure && make
3) Open the system preferences - Date & Time - uncheck Set date and time automatically (to stop the process)
4) Rename the old object and then replace/copy them with the new objects
cd /usr/bin
sudo mv sntp sntp.old
sudo mv ntpq ntpq.old
sudo mv ntp-keygen ntp-keygen.old
cd /usr/sbin
sudo mv ntpdc ntpdc.old
sudo mv ntpdate ntpdate.old
sudo mv ntpd ntpd.old
cd ~/ntpd-fix/ntp-4.2.8
sudo cp sntp/sntp /usr/bin
sudo cp util/ntp-keygen /usr/bin
sudo cp ntpq/ntpq /usr/bin
sudo cp ntpdc/ntpdc /usr/sbin
sudo cp ntpdate/ntpdate /usr/sbin
sudo cp ntpd/ntpd /usr/sbin
sudo chown root:wheel /usr/bin/sntp
sudo chown root:wheel /usr/bin/ntp-keygen
sudo chown root:wheel /usr/bin/ntpq
sudo chown root:wheel /usr/sbin/ntpdc
sudo chown root:wheel /usr/sbin/ntpdate
sudo chown root:wheel /usr/sbin/ntpd
5) Open the system preferences - Date & Time - uncheck Set date and time automatically (to start the process)
6) Done.
-- update time manually
sudo ntpdate -u time.apple.com
-- check ntpd version (should now be: ntpd [email protected])
sudo ntpd --version

How to show Date and Time with TimeZone

Dear All,
I have to show Date and Time with TimeZone abbreviation,
for example:
1) 31 March 2011 2:30 in india standard time - it should show in screen 31 March 2011 2:30 IST.
2) 31 March 2011 2:30 in Australia/New Zealand - Eastern time zone it should show in screen 31 March 2011 2:30 AEST.
how can i show *Australia/New Zealand - Eastern time zone to AEST*,
I tried with format DD MMM YYYY HH:MM zzz, and i looked time zone API too.
Appreciate your help
Thanks
Daya

Dayananda wrote:
ok, than i have to use zzzz format, as z won't help in my case, so i have to use zzzz which display descriptive value like, Indian Standard Time i.e. ISTPer the javadocs there is a very specific reason why that is a problem especially if you intend to support many timezones in one application.
"+For compatibility with JDK 1.1.x, some other three-letter time zone IDs (such as "PST", "CTT", "AST") are also supported. However, their use is deprecated because the same abbreviation is often used for multiple time zones (for example, "CST" could be U.S. "Central Standard Time" and "China Standard Time"), and the Java platform can then only recognize one of them+."
Thus you have one single case where there can be many and moreover it can change (twice a year I believe.)
There is a standard source for this information although when I tried it it appears to not work.
If the app only needs to display one zone then provide a configuration value that allows a user to overload the display value.
If the app needs to display many values then you MUST inform business users of the problem because there are duplicates and they, not you, need to decide specifically what happens in those cases.

Actual Finish date and time

Hii
How can we set the actual finish date and time to be logged at the time of Technical completion ??
Thanks and Regards
BK

BK,
The "Work ends on" field should be open for edit in IW41.
This field entry populates the "Actual finish date" in the operation when the "Final confirmation" flag is switched on in posting the time confirmation.
Check the settings in the IMG for: Set Field Selection for Completion Confirmation.
It sounds as though this has been set to "display only". There is no reason to have this control unless the system is set to enable posting in the future. Then folks would be able to cheat on their time.
The future date posting should only be switched on in development or test clients for test purposes.
However, from your description of the process, I would have expected the date and time to have defaulted as the current date and time.
Could there be a user exit at work?
We seem to have wandered away from the original question you were asking about setting the order "finish" date from technical completion. Were you refering to "Basic Finish Date"?
The configuration in Define Proposed Reference Time for Technical Completion can be configured to be Current, Created on, Basic start, Basic finish, but this relates to the reference date of the order.
Or are we on track now with the problem around the operation "actual finish date"?

Error: 0271: Real Time Clock Error - Check Date and Time settings.

Hello all,
I have lenovo T430s laptop that is configured with Bitlocker encruptions and TPM PIN entry. I don't think that has anything to do with the error msg I am getting but here it is. Error: 0271: Real Time Clock Error - Check Date and Time settings.
Press Esc to continue or F1 to enter setup. I am unable to get into BIOS or even the login screen for Windows 7.
Any advice would be appreciated.

Thanks to everyone for the help. Just want to close this out. I had a IBM/Lenovo technician here today and he replaced the CMOS battery. Upon the change, the computer is fine being reconnected to the dock (the three times I tried it). So it has been resolved with the battery. Surprised by the incompatibility claim because I am not having issues now. Wondering if it's just a USB 2.0 vs. 3.0 thing (and Lenovo trying to sell more peripherals, of course).
Thanks!

Not able to set date and time

I have a problem with automatic date and time will not initiate. I have wireless connection verified; my DHCP is properly configured, the latest i-Tunes software update, homesharing ID matched with computer and security firewall verified configured properly for allowing all incoming connections. Second Apple TV 2 bought in past two days where it will not update wirelessly. Is this a port problem, NTP, or related to software update that went wrong?
Contacted router vendor to troubleshoot their device. Verified with my computer, the wireless router works. Has anyone seen this problem before?
Thanks!

Welcome to the Apple Community.
If you have previously been able to use your Apple TV without this problem, you might try restarting the Apple TV by removing ALL the cables for a 30 seconds. if this doesn't help try a restore.

Date and time configuration

Similar Messages

Maybe you are looking for