DELL XPS 12 BSOD when not used for several minutes

Dear all,
since one month I'm experiencing a strange behavior from my DELL XPS 12 9Q33, Mid 2013 with Windows 8.1 Pro. When the notebook is left unattended for more than 5 minutes, it freezes with the BSOD with two different causes: KERNEL_SECURITY_CHECK_EXCEPTION
and
IRQL_NOT_LESS_OR_EQUAL. I already activated the Verifier Utility and debugged the results of the memory dump, obtaining following reason:
DRIVER_IRQL_NOT_LESS_OR_EQUAL (d1)
An attempt was made to access a pageable (or completely invalid) address at an
interrupt request level (IRQL) that is too high. This is usually
caused by drivers using improper addresses.
If kernel debugger is available get stack backtrace.
Arguments:
Arg1: ffffcf80c94c2fb8, memory referenced
Arg2: 0000000000000002, IRQL
Arg3: 0000000000000000, value 0 = read operation, 1 = write operation
Arg4: fffff800b76aa534, address which referenced memory
Debugging Details:
READ_ADDRESS: GetPointerFromAddress: unable to read from fffff80157965138
unable to get nt!MmNonPagedPoolStart
unable to get nt!MmSizeOfNonPagedPoolInBytes
ffffcf80c94c2fb8
CURRENT_IRQL: 2
FAULTING_IP:
ndis!ndisNsiGetInterfaceInformation+5f5
fffff800`b76aa534 498b8e98050000 mov     rcx,qword ptr [r14+598h]
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: VERIFIER_ENABLED_VISTA_MINIDUMP
BUGCHECK_STR: AV
PROCESS_NAME: svchost.exe
ANALYSIS_VERSION: 6.3.9600.17298 (debuggers(dbg).141024-1500) amd64fre
TRAP_FRAME: ffffd001775b82c0 -- (.trap 0xffffd001775b82c0)
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=0000000000000005 rbx=0000000000000000 rcx=0000000000000000
rdx=0000000000000005 rsi=0000000000000000 rdi=0000000000000000
rip=fffff800b76aa534 rsp=ffffd001775b8450 rbp=0000000000000002
r8=0000000000000007 r9=fffff800b87dd054 r10=0000000000000000
r11=ffffd001775b87f0 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0         nv up ei ng nz na pe nc
ndis!ndisNsiGetInterfaceInformation+0x5f5:
fffff800`b76aa534 498b8e98050000 mov     rcx,qword ptr [r14+598h] ds:00000000`00000598=????????????????
Resetting default scope
LAST_CONTROL_TRANSFER: from fffff8015775e7e9 to fffff80157752ca0
STACK_TEXT:
ffffd001`775b8178 fffff801`5775e7e9 : 00000000`0000000a ffffcf80`c94c2fb8 00000000`00000002 00000000`00000000 : nt!KeBugCheckEx
ffffd001`775b8180 fffff801`5775d03a : 00000000`00000000 00000000`00000002 ffffd001`775b3000 ffffd001`775b9000 : nt!KiBugCheckDispatch+0x69
ffffd001`775b82c0 fffff800`b76aa534 : 00000000`00000002 ffffe000`e5677200 00000000`00000000 ffffe000`e56771a0 : nt!KiPageFault+0x23a
ffffd001`775b8450 fffff800`b6f84572 : ffffd001`775b85c0 ffffe000`e8d98d02 ffffe000`e8d98d00 00000000`00000000 : ndis!ndisNsiGetInterfaceInformation+0x5f5
ffffd001`775b8500 fffff800`b87d6a25 : 00000000`00000050 00000000`00000050 ffffe000`e42c2de0 00000000`00000000 : NETIO!NsiGetParameterEx+0x222
ffffd001`775b8660 fffff800`b87d6be3 : 00000000`00000000 ffffe000`e86900e0 ffffe000`e8690010 ffffe000`e768e9f0 : nsiproxy!NsippGetParameter+0x195
ffffd001`775b87f0 fffff801`57c7b911 : ffffe000`e8690010 00000000`00000002 00000000`00000000 fffff801`578a5701 : nsiproxy!NsippDispatch+0x53
ffffd001`775b8830 fffff801`57a2777f : 00000000`00000000 ffffd001`775b8b80 ffffe000`e8690010 ffffe000`e768e950 : nt!IovCallDriver+0x3cd
ffffd001`775b8880 fffff801`57a26d22 : ffffd001`775b8a38 00000000`00000000 00000000`00000000 00000000`00000000 : nt!IopXxxControlFile+0xa4f
ffffd001`775b8a20 fffff801`5775e4b3 : ffffe000`e61fd080 00000000`001f0003 0000009c`1f6ff658 00000000`00000001 : nt!NtDeviceIoControlFile+0x56
ffffd001`775b8a90 00007fff`88a9123a : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiSystemServiceCopyEnd+0x13
0000009c`1f6ff6d8 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : 0x00007fff`88a9123a
STACK_COMMAND: kb
FOLLOWUP_IP:
NETIO!NsiGetParameterEx+222
fffff800`b6f84572 8bd8            mov     ebx,eax
SYMBOL_STACK_INDEX: 4
SYMBOL_NAME: NETIO!NsiGetParameterEx+222
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: NETIO
IMAGE_NAME: NETIO.SYS
DEBUG_FLR_IMAGE_TIMESTAMP: 546029c5
IMAGE_VERSION: 6.3.9600.17485
BUCKET_ID_FUNC_OFFSET: 222
FAILURE_BUCKET_ID: AV_VRF_NETIO!NsiGetParameterEx
BUCKET_ID: AV_VRF_NETIO!NsiGetParameterEx
ANALYSIS_SOURCE: KM
FAILURE_ID_HASH_STRING: km:av_vrf_netio!nsigetparameterex
FAILURE_ID_HASH: {f5408a12-c1db-c14f-1bc7-98a11ba14432}
Followup: MachineOwner
Thanks in advance
Dr. Paolo Casoto

PC
We do need the actual log files (called a DMP files) as they contain the only record of the sequence of events leading up to the crash,
what drivers were loaded, and what was responsible.
Please follow our instructions for finding and uploading the files we need to help you fix your computer. They can be found here
If you have any questions about the procedure please ask
Wanikiya and Dyami--Team Zigzag

Similar Messages

Mail app closes when not used for a while how fix?

mail app closes when not used for a while how fix?

This may also be due to the Sudden Termination feature built into OS X, which will effectively quit a process if the system is demanding resources. Mail can be a RAM hog at times, and if your system only has a few GB of RAM, then when other programs demand more and you have not been using Mail then the system will invoke Sudden Termination to quit it so more RAM is available elsewhere.
Do you have only ~2-4GB of RAM in your system? Check for this in the About This Mac option in the Apple menu, and if so then consider upgrading to more if your system supports it. Alternatively you can try quitting other applications to free up more RAM.
To see which programs are using the most RAM, open the Activity Monitor utility and choose My Processes from the drop-down menu. Then ensure Real Memory is checked in the View > Columns menu, and click this menu's title to sort the items by it.
Keep in mind that sudden termination does not fully quit the program, so Mail may still show up in Activity Monitor when you open it even though it may be closed from the Dock.

My ipad disconnect to wifi when not using for a while

My ipad disconnect to wifi when not using for a while. is that normal?

This is absolutely normal, the iPad is turning off after a certain time to conserve energy…
If you are making large downloads, go to the "Settings", "General", "Auto-Lock" and set it to a higher value…
enjoy your magic machine

HP B210a goes into a sleep mode if not used for several hours,

Running my B210a eprinter in windows vista. The printer goes into a sleep mode if not used for several hours. The power button is slowly flashing dim then bright, and I need to manually touch the printer's screen to enable it to print. If printer not used for several days, the only way I can make it work is to unplug and plug. Any suggestions or help appreciated. J Rice

What OS? Wired or wireless connection?
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Firefox does not respond for several minutes when coming logging on after locking my vista laptop

This has happened for several days in a row but it happened sporadically before the update to 6.02. The laptop is a Compaq Presario C700 2GB RAM, plenty of space on the hard drive, Vista 32-bit SP2. I do not have a problem using IE or Chrome. I do have about 10 tabs open (this varies to less to more depending on what I'm working on) however, it has happened with less and more.

Clear Cookies & Cache
* https://support.mozilla.com/en-US/kb/Template:clearCookiesCache
Clear the Network Cache
* https://support.mozilla.com/en-US/kb/How%20to%20clear%20the%20cache#w_clear-the-cache
Troubleshooting extensions and themes
* https://support.mozilla.com/en-US/kb/Troubleshooting%20extensions%20and%20themes
Check and tell if its working.

Tried to sing into my ipad after not using for several months. it asked me for a 4 digit passcode, can't recall having to do that before. tried some common ones i use. it finally locked up. what do i do?

after several months not using it, i tried to start up my ipad. it asked me for a passcode (4 digit). after i tried some possible ones, it locked me out. what do i do??

Recovery Mode Step by Step
1. Hold Sleep/Wake button down and slide to turn off iPad
2. Turn on computer and launch iTune (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port. Do not release button until you see picture of iTune and plug.
5. Release Home button.
On Computer
6. iTune has detected iPad in recovery mode. You must restore this iPad before it can be used with iTune.
7. iPad Recovery Mode on computer screen
8. Select "Restore iPad"...

Unplug if not using for several days?

If I am going out of town for several days, I always turn off my mac. Would it be a good idea to unplug it too? I never have before, but I was thinking today that that tangle of wires plugged into the surge protector seems like a waste of energy.
Advice appreciated.
Thanks very much in advance.

Thank you all so much for your advice. Sorry to be so long in saying 'thanks', I was out of town. I decided against unplugging the computer. The storm chances are fairly low, and it would be awful to run down the memory battery, as the closest Apple store is over an hour away in Austin. Thank you all again for your help.
Regards,
Jane

What to do with Time Capsule when not using for Wireless Internet

I previously connected my Time Capsule to my fiber optic router but in my no home this is no longer needed as the cable TV company now provides 160 MPS Internet in a router that contains a wireless router built in. It works fine. My computer is now connected wirelessly to that router (too far to take advantage of the wired connection).
Therefore I want my Time Capsule to just be connected to the computer for backups. I gather I have to connect it via Lan and make sure it does not transmit r receuve wirelessly. In fact, other wireless computers in the huse occasionally try to log into the old Time Capsule PPoE settings, so I want to erase them and start fresh.
This seems to be similar to what I want t do, but I want to make sure and ask:
https://discussions.apple.com/message/8256674#8256674
If this is not correct, can someone advise.
By the way, I have a first generation Aiport Express that I hope to use with my new cable router (modem?). I assume it will work as it did with the Time Capsule. Purpose is for Airplay with an audio system.
Thanks!

Thank you for your replies. I really appreciate it.
To answer your questions in order, but first I should mention that due to work reasons, I will be away from my computer until Friday night Japan time, or Friday AM US time.
Anyway, probably better I go slowly,as I tend to get overwhelmed by technical things.
1) You said: "The TC does NOT require an Internet connection for network connectivity. You DO have to connect the TC by Ethernet to the Fiber Optic router in order for it to gain network connectivity AND to allow network clients to access it."
-->Ok, this is in reference to my Time Capsule and the previous network n myold apartment. But your next question makes me wonder:
2) "Is this Motorola device the one that replaced the Fiber Optic router that you mentioned in your original post? What is its model number? Do you have the TC connected directly to it by Ethernet?"
Ok, this is what I have:
Wall--> Cable modem with wireless (Motorola SURFboard SBG6580J Wireless Cable Modem Gateway.)
Other Room IMAC connected wirelessly to Cable Modem (no Ethenet connection to it since there is no jack and too far to run a cable (permanently--I can do for setup if needed)---> connected to TC and Time Capsule is backing up ok. Time Capsule is also not connected to the Modem
3) "Since you will only want to use the Time Capsule for Time Machine backups, I understood that you wanted to disable its wireless network. If this is still the case, the Express would need to be configured to join the wireless network provided by the Motorola wireless router."
Yes, This is what I am wondering. Do I have to connect it by LAN to the Motorola? A few times, when it was just plugged into the Wall, my Mac airport utility found but them could not connect to my Express. maybe because I did not configure it to work with the Motorola as you say.
4)
"By default the Express will broadcast its own wireless network with a network name of something like: Apple Network NNNNNN. You would need to connect to this network with your computer prior to attempting to access it with the AirPort Utility. Another option would be to temporarily connect it, by Ethernet, to the Motorola router during its setup phase. Once completed you can move it to the desired location."
Ok, this confirms what I guessed. Connecting the computer to the Expressby Lan? Is that what you mean?
I do understand the second option---connecting the Express to the Motorola.
If that is right, I can try that. Do I need to do anything other than connect it?
I will be able to try this Friday or Saturday I hope.
Once again. thanks for all your help. Really appreciate your taking the time to explain it.
paul

How to store printer when not used for extended period.

Printer will remain in unheated summer cottage. I plan to remove print head with cartridges for storage in a heated home. Will the cartridges dry out and/or would ink congeal in printhead as one instruction says not to remove cartridges until ready to replace with new. Any suggestions?

Printer will remain in unheated summer cottage. I plan to remove print head with cartridges for storage in a heated home. Will the cartridges dry out and/or would ink congeal in printhead as one instruction says not to remove cartridges until ready to replace with new. Any suggestions?

Photoshop Elements not working right after not using for several months?

Have Photoelements #10 on this computer. Have been away, using #10 on another computer, now back and PhotoElements #10 is NOT working properly?

Hi,
Please try couple of probable solutions as mentioned below:
Solution 1:
1. Close Elements.
2. Launch the Photoshop Elements Welcome Screen and hold down ctrl + alt + shift as you click Editor.
3. Continue to hold the keys until you see a message box asking if you want to delete Photoshop Elements settings file; click Yes. Elements will open with default preferences.
Solution 2: In case any network printer is attached try to launch without network or printer uninstall or make different printer as default.
Solution 3: Try launching with anti-virus off or removing PSE from conflicting list.
Solution 4:
On the drive on which you have installed PSE,on my machine it is on C:
Go to C:\Program Files\Adobe\Photoshop Elements 10\Locales\<locale>\Plug-Ins\Import-Exportand you will find twain plug-in. Remove that plug-in from that location and copy it somewhere else.
Now launch PSE and check if it works.
For related post for Twain please see this:http://forums.adobe.com/message/2954743#2954743
Thanks,
Garry

Why when I try to update certain app it require an old email address and password I have not used for years and I do I get to update them on my new details

Why when I try to update certain app it require an old email address and password I have not used for years and I do I get to update them on my new details

Apps are tied to the Apple ID that was used to purchase them and you will always need to use that ID and password in order to update them.
Saying that you do get to update them on your new details makes no sense at all.

Should I unplug my AE when not using it for months at a time?

should I unplug my AE when not using it for months at a time?

Yes, in my opinion.....unless you really like to have a green light "on" all the time.

I downloaded Firefox 7 and when I click on the browser icon nothing happens, the browser does not load on desktop.I had no problems with Firefox 4 I had been using for several years and liked very much

I downloaded Firefox 7 and when I click on the browser icon nothing happens, the browser does not load on desktop.I had no problems with Firefox 4 I had been using for several years and liked very much

Most people have no problems with installing firefox as an upgrade, but there are quite a few things that can cause problems. Please have a look at the articles
* [[software Update Failed]] <-- clickable link (blue ) --
* [[firefox will not start]]
* [[firefox does not work]]
Post back after you read them and say what you tried. Have you ensured you used an admin account, possibly needing to check the UAC setting, and that security software is not blocking the changes. You should certainly try starting in firefox's [[safe mode]] either from a menu/icon option or by holding the shift key as you attempt to run firefox.
Is the browser icon you see on the desktop, and a firefox icon ?

How do I turn off background ni file activity when not using Labview? files such as nimxs.exe, nipalsm.exe, nipalsm.exe, nisvcloc.exe, nicitdl5.exe

How do I turn off background ni file activity when not using Labview? I use labview rarely, and I also use my computer for demanding multimedia applications, including multitrack digital audio recording. I need to reduce as much background activity as possible, and taking a look with task manager I see files such as nimxs.exe, nipalsm.exe, nipalsm.exe, nisvcloc.exe, and nicitdl5.exe running even when I haven't used Labview (8 I believe). These files run even after I right click the NI icon on the lower right and turn off the application. I would like the computer to boot up without these files, and for the necessary files to be activated only when I start the program.
Can this be done or do I have to remove labview from the system to improve performance?
Thanks

Hello, those processes are part of running NI services that start when Windows boots. These processes serve varied purposes and stopping them can have undefined and unknown consiquences for your NI products. These products run at "normal" priority meaning that they should be preempted by any process running at a higher priority which I would expect your other application to be doing given their time sensitivity. That being said, in Windows XP (I can't speak for other OSes), you can lower their priorities even greater through task manager (right click the process»set priority) to further remove them from contention for resources. If you want to prevent them from running you can set the service startup type to "manual" in Control Panel»Administrative Tools»Services. Right click the process go to Properties and Under the General tab choose Startup Type»Manual. This will start up the processes only when something directly starts it up. LabVIEW will start these processes up as it attempts to use them. When you shut down LabVIEW you will need to manually shut down these processes through task manager. Again, doing this can cause problems with your NI products on your system and it is not advised.
Travis M
LabVIEW R&D
National Instruments

Is there any way to turn off airport without removing the electrical plug and should I unplug it when not using it??

I just got the 5G Airport Extreme base station. Set-up was a snap! Maybe 10-15 minutes compared to a friend who got another name brand for his pc and took a couple hours, even having to call customer support! Been working great so far, but am concerned about never turning it off, not only about the possibe harm that could be done to the unit, but also about having an active, open Internet connection 24/7. Before I got my Airport Extreme I was using Ethernet cable with a cable modem that could be placed on "standby" whenever I was not using my Mac for Internet, but since AE5G doesn't have a power switch on the unit, have left it turned on rather than unplugging it by the electrical cord. I did turn AirPort "off" in the menu bar when not using it wth my Mac, but AE is still apparently constantly active, showing a steady green light. Would there be any harm done by plugging it in only when I want to use Wi-Fi, then unplugging it?
Thanks for the help!

Would there be any harm done by plugging it in only when I want to use Wi-Fi, then unplugging it?
That is a matter of debate, since there are two schools of thought regarding power status on a router.
One school maintains that you can turn the device on and off as needed. Makes sense for some folks. The advantage of this is that it might save a bit of electricity, although the Extreme draws very little power most of the time.
Another school believes that there is a reason why Apple did not even place an "Off" switch on the device. It's designed to run 24/7.
Leaving the Extreme on will place far less stress on the electrical components in the device since they stay in an "idle" state most of the time, drawing very little current. Powering any electrical device up sends a sudden rush of current through the device, which places far more stress on a device than if it is simply left on.
It depends on your priorities. If you want to save electricity, your decision is already made. If you intend to prolong the life of the router, then consider leaving it on, as Apple intended.
A compromise position might be to leave the Extreme on most of the time and power if off for long weekends or vacation periods when you will be away. Remember that the Extreme must establish all new network connections every time that it powers back up....perhaps another reason to simply leave it on.

DELL XPS 12 BSOD when not used for several minutes

Similar Messages

Maybe you are looking for