Deploy a image by Task Sequence - then can't see it in software centre after a rebuild.

i've made a task sequence for installing an OS, that works fine, i've created a collection, added my machine in there gone to the software library --> task sequence --> created a deployment and targeted the collection.
Log onto the machine in that collection open up software centre, i rebuild the machine using that task sequence, but then when i log back into the machine the TS isn't there anymore.
i've checked to see if the machine is still in the SCCM device collection (it is) i've checked to see if it's the right machine and not some duplicate (it isn't) i've made sure there is only one machine with that name in the all systems collection and they
have the same SCCM ID.
I want people to be able to rebuild their machines whenever they want to.

Hi,
are the Deployment Settings : Deployment settings action is install, purpose available. Make available to configmgr clients, media, and PXE.
also check advance properties of the task sequence, on which platforms you have enabled task sequence to run & also check advertisement interaction properties.
The above two checks are from This
https://social.technet.microsoft.com/Forums/en-US/ea34254c-261e-46c1-a288-a6f5c8531c89/computers-not-displaying-task-sequences-in-software-center?forum=configmanagerosd
Regards
Tanoj
OSLM ENGINEER - SCCM 2007 & 2012

Similar Messages

I usually have annexes in my outlook tasks, but I can´t see them in the apps I downloaded, is there any app I can use yo do this?

I usually have annexes in my outlook tasks, but I can´t see them in the apps I downloaded, is there any app I can use yo do this?

With the iPad connected to the computer, while iTunes is running, click on the iPad name on the left side under devices. Click on the Movies tab and look for Movie Rentals. You want to "Move" the films to the iPad.

MacBook can't see my home wireless network after upgrade to OSX 10.8.5

After upgrading to OSX 10.8.5, my MacBook does not detect any wireless nertworks. My iPad and iPhone work fine, my router has been rebooted, WiFi is turned on, and the ethernet connection is how I am writing this message to you via broadband. There are a half dozen wireless networks in range (according to my iPhone) but the MacBook cannot find the router I am sitting next to. Any ideas on how to correct this issue?

It appears an SMC reset was required:
HT5815 I've just done the 10.8.5 update on my MacBook Pro end of 2008, and WiFi don't work after reboot... Impossible to activate it...
Here is your other post: MacBook can't see my home wireless network after upgrade to OSX 10.8.5
If you reply to it and marked it "solved", perhaps with a link to that post (copy and paste it, or just say you performed the SMC reset) it will help others find a solution. Thanks!

Powershell commands to change operating system image in task sequence

Hello,
I am looking for a way to script changing a task sequence to use a different OS image file. So far the only thing I can find using the powershell MDT module is the "import-mdttasksequence" command, but it looks like that can only create a whole
new task sequence.
My end goal is to automate our master image builds and the last step is to take the captured master wim file, import it into the Operating Systems folder, and then update the associated custom image task sequence to use that new OS image. With
"import-mdttasksequence" I have to create a new task sequence with a new ID, when I already have one present that would be easier to just update to point to a different OS image. I do not see anyway to edit task sequence steps using the powershell
module.
Is this possible? Maybe using Get-Item to get the OS GUID and then editing the task sequence XML file directly?
MDT 2013
Server 2008 R2
Regards,
Darren

Hi Darren,
If I understand correctly, you can use the same name for the captured WIM file? Then you can just copy it to the operating systems and it will be picked up by your TS.
I've found this
thread on the forums that probably has your solution in it.
From that thread:
I now capture to the Captures folder and name the WIM file after the task sequence ID. So for example, my "Update Windows 8 General Purpose" task sequence with ID "8_GP" now creates "\\server\DeploymentShare$\Captures\8_GP.wim"
In the Scripts folder on the deployment share I created "Relocate.cmd" with the following contents:
MOVE /Y "%DEPLOYDRIVE%\Captures\%1.wim" "%DEPLOYDRIVE%\Operating Systems\%1"
And finally, I added a step at the end of my task sequences that runs this custom command (no
Start in value defined):
cmd /c %SCRIPTROOT%\relocate.cmd %TaskSequenceID%
This works great and MDT does in fact recognize the changed .wim file in Operating Systems and copies it to linked deployment shares, so no worries there.
Hope this helps.

Non-Deployed Applications in OSD Task Sequence Are Deployed To Collection Members where OSD TS is deployed

Hello,
I have a situation where an application (which is not deployed) that is part of an OSD Task Sequence is being deployed to computers that are in the same collection my TS for OSD is deployed.
For OSD I have created an application to check the BIOS version and upgrade the BIOS if there is a newer one available. The application has numerous deployment types (13) due to various hardware models and the requirement to go to several intermediary BIOS
versions to reach the current newest version. There are dependencies configured to handle these incremental bumps.
The OSD TS is deployed to a collection that contains all windows desktop class operating systems. What I have seen happen once is that one users workstation somehow discovered and installed the BIOS Upgrade package and their BIOS was upgraded on their workstation.
I've checked the logs on several other machines and this same application has been run as well.
The application is configured "Allow this application to be installed from the Install Applications
task sequence action without being deployed" which allows it to be ran from a TS even though it is not deployed.
I have verified the application is not deployed. I have verified there are no superceedence rules configured. As I stated, there are dependencies, but all dependencies are within this one application.
What I do not understand is, how can an application that is not
deployed and is only referenced in an Operating System Deployment Task Sequence able to be ran outside the task sequence?
This is/has occurred with computers imaged with cm2012 and with computers imaged with cm2007 who have now been migrated to cm2012.
I'm fairly sure that it is due to the task sequence and where it is advertised. Computers that are not in this collection do not show the application being applied in the AppEnforce.log. If it is the TS that is causing this, how can something that is designed
to be a "sequence of tasks", allow something to occur out of that sequence?
Current environment is CM2012R2.
Any thoughts to what might be happening?
Thanks

Hello,
After working with Microsoft Support, we were able to resolve the issue.
Turns out there was something (old policies) "stuck" in the SCCM database that was causing this to be advertised outside the task sequence and not visible on the console. While they didn't call this "a bug" since it has happens with CM2007 as well, it definitely
was not normal behavior. Still not sure how that could happen as I'm 99.99% sure I never deployed this to any collection, but that's what they said.
It took several hours of support rooting through the database to figure out what was going on but after some SQL magic it was fixed. Sorry I don't have more specifics regarding the fix. MS basically said "If it happens again you can do this this and this
in the db and voila its fixed". Since I'm likely to cause more damage (messing with the database) then good if it were to happen again I'd contact them.
Anyway, this odd behavior has spooked me and I've reverted back to deploying the TS to the unknown computer collection. As much as it disappoints me to take a step back and cause more work for the guys doing the imaging, the extra safety this grants (if
something like this or worse were to happen) I think is better than an OSD task sequence gone wild.
Thanks,
Mark

Sysprep and Capture Task Sequence Fails "Can not find script file C:\LTIBootstrap.vbs"

I've just installed Windows 8 on a Lenovo ThinkPad T440s using Lenovo's recovery discs. I did not join it to a domain. I logged in as Administrator, navigated to our deployment share, and ran Scripts\LiteTouch.wsf. I selected the new Sysprep and Capture
Task Sequence that I just made, told it to upload to DeploymentShare$\Captures, then started the Task Sequence.
It seemed to run fine until after the first reboot. Windows 8 configured the PC for a while, then displayed an error that it had been shut down unexpectedly. I wasn't sure if this was normal, so I just clicked OK. Then I got an error that said "Can
not find script file C:\LTIBootstrap.vbs". After clicking OK on that, I am brought to the desktop.
The image cannot be found in DeploymentShare$\Captures. Under the Monitoring section of the DeploymentWorkbench, I can see that MDT thinks the Task Sequence is still running on the machine (though it is not), with progress stuck on step 16 of 23: Execute
Sysprep. There are 0 errors and 0 warnings listed.
BDD.log is too long to post all of it, but here's the last few lines in case that's helpful.
<![LOG[BCD> The operation completed successfully.]LOG]!><time="11:20:35.000+000" date="12-26-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[BCDEdit returned ErrorLevel = 0]LOG]!><time="11:20:35.000+000" date="12-26-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Run Command: C:\windows\SYSTEM32\bcdedit.exe /default {d22e7e91-9ee7-46eb-89d7-c5859e4302f0}]LOG]!><time="11:20:35.000+000" date="12-26-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[BCD> The operation completed successfully.]LOG]!><time="11:20:35.000+000" date="12-26-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[BCDEdit returned ErrorLevel = 0]LOG]!><time="11:20:36.000+000" date="12-26-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Property BootPE is now = True]LOG]!><time="11:20:36.000+000" date="12-26-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[LTI Windows PE applied successfully]LOG]!><time="11:20:36.000+000" date="12-26-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Event 41019 sent: LTI Windows PE applied successfully]LOG]!><time="11:20:36.000+000" date="12-26-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[LTIApply processing completed successfully.]LOG]!><time="11:20:36.000+000" date="12-26-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
<![LOG[Event 41001 sent: LTIApply processing completed successfully.]LOG]!><time="11:20:36.000+000" date="12-26-2014" component="LTIApply" context="" type="1" thread="" file="LTIApply">
I would greatly appreciate any assistance determining what went wrong and how to correct it. Thank you.

You might get teh c:\LTIBootStrap.vbs error if you are running SysPrep with a unattend.xml template that contains the c:\bootstrap.vbs template, yet you are *NOT* deploying the image with MDT Litetouch, instead just applying the image to the final machine.
Crack open your install.wim file and search for the unattend.xml file in the normal places to see what it is.
I am concerned about the "shut down unexpectedly" error. There should be no shutdown state information left from a captured *.wim file.
If you still need assistance, please feel free to copy the bdd.log file to a public site like OneDrive, and share the link.
Keith Garner - Principal Consultant [owner] -
http://DeploymentLive.com

OS Deployment - Unable to read task sequence, WpeInit.exe does not start automatically

Ok so this is a very very weird one.
this is my first time actually coming to the community for help. I need assistance asap.
I have 4517 systems in SCCM 2007, we have a mixture of PXE enabled offices and offices with just DPs that use boot media for OSD. I use the SAME boot image for our PXE enabled task sequence as I do for our boot media. I create an ISO file for our remote
staff and they in turn use it to OSD in those offices.
We have three offices where no matter what I do WPEInit doesn't seem to run and it either instantly reboots (no network) or prompts with the error message in the title. Interestingly enough if you PXE boot that SAME machine it works fine using the identical
boot image.
We have tired:
- New USB keys
- Different machines
- BIOS defaults
- Legacy settings for UFEI / Defaults
- PXE boot (works fine...)
- Another SCCM Boot image from an earlier Task Sequence (still doesn't work)
- MDT Boot image, works fine...
any clues? What makes these three offices so special that they refuse to work with a boot image that works everywhere else in our Canadian offices?!

I believe this issue has to do with how the USB drive reports its "type." In my testing, a USB drive that reports itself as a "fixed" disk will not work as an SCCM boot disk. They have to be "removable." USB drives that
are certified for Windows To Go for example have NOT worked in my experience, because they report as a "fixed" disk. This is usually a problem with high capacity USB drives.
We found some 16GB USB drives that work great, and they report to the OS as being "removable." DISKPART can tell you whether a driver is fixed or removable. In the screenshot below, the second drive will not boot SCCM. The first drive will.

MDT 2012, Task Sequence Comments, can I change to have line breaks?

I added comments to a few Task Sequences. They all run into each other, I'd like to be able to type a sentence, press enter, then put another, but when I do this, that's not how it looks in LiteTouch.vbs.

I wanted to do the same thing and could not come up with a nice way to do it. Ended up using the hidden character Alt+0160 to space it out. Looks good now but took some trial and error to get it all lined up.

How can I see my ipad on itunes after cut the restore?

I was restoring my ipad then I accidently closed the itunes by Task Manager and now I can't see my ipad in itunes or any similar program but when I plug my ipad to the PC I can hear the alert means it's plugged , and I can see it in Device Manager , and I can't put it in DFU mode or anything else because I have no screen or home&power button.
sorry for my English.
t

Hello moamal,
Welcome to the Apple Support Communities!
I understand that when you connect your iPad to your Windows computer, iTunes does not recognize that it has been connected. For this situation, I would recommend working through the troubleshooting steps outlined in the attached article to resolve this.
iPhone, iPad, or iPod touch not recognized in iTunes for Windows - Apple Support
Cheers,
Joe

Can't see anything in external drive after renaming a folder

Hi all,
I can't see anything on my external drive after renaming a folder. I have the drive set up as a Windows drive with access through the volumes folder (I had to transfer large amount of files from a PC and have it be readable on my MacBook Air); I read a FAQ to set it up a few months ago and it has been working fine since then. I saw the same issue come up with a PC HD on a PC, but the solution was for a PC. I don't see anything else like that in the support community (or if it's there, then I'm not searching for it the right way). There is no partition on the drive and it still shows as having the same amount of data written on the drive as before the accident.
Many thanks in advance!
anj

If you upgrade the your router, it would be the firmware that will be upgraded. For more information regarding upgrading the firmware, try this link.
For your external drive, you might need to map the drive again with a different name.
Hope this helps.

Third party app can only see but not use library after current update

An application that has been using the iTunes library to play music from play lists can no longer read and use the library but can only see the library. This is happening since running the iTunes update to 12. I have corrected the problem by reloading maverick and loading music into iTunes after a fresh install. The app works again with a fresh mavericks install. So, now what is the order of operations to backdate to an earlier version of iTunes? My library can no longer be read by the mavericks install as it has been updated by iTunes 12.
I am using an external drive FYI.
I was thinking I would use the mavericks install and create a new library on the external and move the music folder to the same directory and then add the whole directory. Then one by one import the play lists.
I don't know what to do about the artwork directory? Do I move it and replace the same folder in the new mavericks library directory? Will the above process complicate the assignments?
If apple reads this... The version update that did away with coverflow was the beginning of iTunes decline. It wasn't broke. It was close enough to perfect as a library management tool. You should make the next version closer to that one.

I had a similar problem when trying to install Zinio.air. I have made it all work out. What i did was remove Adobe Air 15 entirely from the Utiliites and Library/ accounts and preferences. I then downloaded Adobe Air 13 and installed and then clicked on Zinio .air and it all installed ok. I also had to temporarily change security settings from Apple approved to Anywhere. All functioning now.

Can't see audio wave in viewer after FCP5 project updated into FCP2

After updating my project from old FCP 5 version running on Tiger to FCP2 running on Leopard, I can't see the audio wave picture inthe viewer window. Is there an explanation for this?
Thanks assistance.
Ray

You can try clearing the waveform cache in your project folder. Press Shift Q to open the System Preferences window. Look for the location that is set as your Waveform Cache location, then use the Finder to navigate to that folder. Remove the cache files from there, and then try relaunching your project to see if that solves your issue.

I can not see my husbands Itunes library after he has shared his library

My husband has shared his Itunes Library, but I can not see it on my computer. Any suggestions?

So what sync settings do you currently have enabled from under the iPod's Summary and Music tabs? Any error messages when you try to sync?
To be sure, reset sync warnings. To do this, right->click the iPod under Devices and choose Reset Warnings. Then resync your iPod.
B-rock

Can't see library itunes in iphoto after Yosemite upgrade

I can't see my itunes library in iphoto following upgrade to Yosemite. I can't use my music in iphoto slideshows.

In iTunes go File -> Library -> Organise Library -> Reorganise Library.
Then quit and restart iPhoto.
Credit to user keysandfood who figured that one out.

Need advice.Can't see Business Transactions in CRMD_ORDER after 7.1 upgrade

Hello Experts,
We've done 7.1 upgrade and somehow now I can't see all our Business Transactions in CRMD_ORDER.
I executed TCode CRMD_ORDER > went to Business Transaction > Create > and I can see just few Business Transactions, not full list of them as in 7.0.
Now I can create only Business Activity, Outgoing E-Mail & Task. No option to create and see Change Order, Change Document, Corrections (Normal, Urgent, etc) etc.
Any idea why? Please advice.
Thanks
123
Edited by: SOLMAN123 on Nov 23, 2011 11:31 AM

Hello Prakhar
Thanks for advice, really useful!
Can you please clarify where exactly I can create the Busines Transactions, such as Norman Correction?
I would like to create Normal Correction via SOLMAN_WORCENTER,so I navigated to Change Management > Common Tasks > New Request for Change (for instance)
After that I'm getting the list of various roles, such as:
Select a business role: AIC_MANAGER-AIC Manager
IC_AIC_AGENT-Accounting IC Agent
AUT-PM-Automotive Partner Manager
CASEWORKER-Case Worker (Social Services)
.....etc..
and I don't know which one to use.
Can I still use "old-fashioned" CRM transactions for this?
It all has been changed dramatically if you compare it with 7.0
Thanks,
123
Edited by: SOLMAN123 on Nov 23, 2011 7:11 PM

Deploy a image by Task Sequence - then can't see it in software centre after a rebuild.

Similar Messages

Maybe you are looking for