Detecting and configuring a Bosch G-Sensor accelerometer

Wondering if anyone is able to help.
My tablet has a Bosch G-Sensor accelerometer, and I cannot for the life of me find anything on getting it working in linux.
Googling produces a lot of vague info, but I have found that the device most likely hangs off the i2c bus, and there is the bma150 driver in the kernel since 3.1.
Now I am uncertain if this driver will work as I have not found any info on the device version in my tablet, and I cannot seem to find any way to probe the device for stats.
My device is an Acer Iconia Tab W501. I currently have everything working perfectly except for bluetooth and the accelerometer.
All help is greatly appreciated.
Cheers.

.:B:. wrote:
Google gives me this:
https://www.codeaurora.org/git/projects … sc/sensors
Doesn't seem to be in the official kernel tree yet.
Yes, I did find this. I pulled all the files for the driver but I can't get them to compile. Unfortunately, I do not know enough to port the driver from the android tree. Anyway, this is the Froyo branch which is based on the 2.6 kernel series (which is probably why I can't get it to compile). Maybe I need to pull it from the ICS branch (but I still think this is the 2.6 kernel series)
Hopefully someone else may be able to help with this or know of another solution to getting this driver.
Cheers.
Last edited by Padfoot (2012-01-28 20:07:44)

Similar Messages

Configuration for JMS Adapter Sensor action and JMS Queue sensor action..!!

Hi,
Id like my BPEL process to send an XML message to JMS on Websphere,I was able to do this through a JMS adapter.But I would more like to add sensors into my process which would really do the same thing - send an XML message to JMS Q.
Now I understand that there are two ways to do this,JMS Queue and JMS Adapter - thorugh bpel sensor action.
I am able to use JMS Queue and it works fine , but adds its own xml tags to the message,Is there any way I could send only my xml payload as a message to the queue??
Also could any1 tell me what is the configuration for JMS Adapter sensor action?
Any suggestions how do I go about it??

Hey Anirudh,
Thanx for the response :-)
All these hold good when I have an AQ adaptor right,But the thing is I want to send a message to a 'JMS' queue with out actually using an adapter configuration wizard and everythng..So I resolved to JMS queue Sensor action..Heres the xml snippet from the sensorAction.xml files which is generated..
<actions targetNamespace="http://xmlns.oracle.com/Test_JMS_Logging" xmlns="http://xmlns.oracle.com/bpel/sensor" xmlns:tns="http://xmlns.oracle.com/Test_JMS_Logging" xmlns:pc="http://xmlns.oracle.com/bpel/sensor">
<action name="JMS_LogEntry" publishName="" publishType="JMSQueue" enabled="true" filter="" publishTarget="jms/L_Queue">
<property name="JMSConnectionFactory">jms/L_QueueCF</property>
<sensorName>ActivitySensor_JMS</sensorName>
</action>
</actions>
This works grt and adds messages to the queue..But adds its own header info according to the sensor.xsd loacted at the Oracle_home\bpel\system\xmllib\ folder.
Right now the XML message added to the Queue is:-
<actionData xmlns="http://xmlns.oracle.com/bpel/sensor">
<header>
<sensor sensorName="ActivitySensor_JMS" classname="oracle.tip.pc.services.reports.dca.agents.BpelActivitySensorAgent" kind="activity" target="AddLEntr
y" xmlns:pc="http://xmlns.oracle.com/bpel/sensor" xmlns:ns2="http://www.ulrhome.com/2008/10/L_Entry" xmlns:tns="http://xmlns.oracle.com/Test_JMS">
<activityConfig evalTime="completion">
<variable outputDataType="string" outputNamespace="http://www.w3.org/2001/XMLSchema" target="$WriteL_Produce_Message_InputVariable/L_Entry/ns2:L_Entry/ns2:LCName"/>
</activityConfig>
</sensor>
<instanceId>950016</instanceId>
<processName>Test_JMS</processName>
<processRevision>v2009_04_15__40833</processRevision>
<domain>default</domain>
<timestamp>2009-04-15T11:21:23.596-04:00</timestamp>
<midTierInstance>app01.ulrhome.com:9700</midTierInstance>
</header>
<payload>
<activityData>
<activityType>scope</activityType>
<evalPoint>completion</evalPoint>
<durationInSeconds>0.011</durationInSeconds>
<duration>PT0.011S</duration>
</activityData>
<variableData>
<dataType>12</dataType>
<data>
<ns0:LCName xmlns:ns0="LC_Test1http://www.ulrhome.com/2008/10/L_Entry">LC_Test1</ns0:LCName>
</data>
<queryName/>
<target>$WriteL_Produce_Message_InputVariable/L_Entry/ns2:L_Entry/ns2:LCName</target>
<updaterName>AddL_Entry</updaterName>
<updaterType>scope</updaterType>
</variableData>
</payload>
</actionData>
My requirement is that I need to add a sensor to the BPEL process which posts 'Only my payload message to the JMS queue'..
What I would want the message in the Queue to be is : -
<data>
<ns0:LCName xmlns:ns0="LC_Test1http://www.ulrhome.com/2008/10/L_Entry">LC_Test1</ns0:LCName>
</data>
Also while creating a Sensor action I get another option as JMS Adaptor,I am not sure of what value to type in this wizard..Heres what I keyed in..M sure this is not right..Cos it dosnt work :-)
<action name="SensorAction_JMS" publishName="" publishType="JMSAdapter" enabled="true" filter="" publishTarget="jms/LoggingQueue">
<property name="JMSConnectionName">Log</property>
</action>
</actions>
Could any 1 tel me what values are the right values..And does JMS Adapter mean that I have to create a JMS Apator in the project and give that connection name as a Value..
I am not finding sufficiant Documentation for 'JMS Adapter' so M clueless and right now any help will be appriciated :-)
Regards,
Akshatha.

Oracle Enterprise Manager Agent deployment (Installation and Configuration) Error

Hello,
I am trying to create an agent on a linux server using Oracle Enterprise Manager 12.1.0.3. The user is created with root privilege on the server, by change /etc/sudoers entry username the same as the root entry. After that I tried to add host target by clicking Setup->Add Target->Add target Manually->Add Host Targets in the Oracle Enterprise Manager.
In the Add Target view: I clicked on add, then I entry host and platform information. After that I click next. Then I provided the Linux x86-64 : Installation Details for
Installation Base Directory, Instance Directory, Name Credential ... then click next. then click Deploy Agent.
In the Add Host Status view: stages Initialization and Remote Prerequisite Check successfully passed, but in the stage Agent Deployment, it failed in the Installation and Configuration phrase of the Agent Deployment stage.
The log content is shown below. There are numerous SEVERE Errors. But I don't have much experience in dealing with these type of problems. I thank you in advance for all the helps.
lf
WARNING: Validation of XML schema is disabled because AggregateDescriptions.xsd could not be found
INFO: Creating new CFM connection
INFO: Creating a new logger for oracle.sysman.top.agent
INFO: Unmarshalling /users/ncgf/em_agent/core/12.1.0.3.0/inventory/ContentsXML/ConfigXML/oracle.sysman.top.agent.12_1_0_3_0.xml
INFO: Creating a new logger for OuiConfigVariables
INFO: Unmarshalling /users/ncgf/em_agent/core/12.1.0.3.0/inventory/ContentsXML/ConfigXML/OuiConfigVariables.1_0_0_0_0.xml
INFO: Aggregate Description oracle.sysman.top.agent:12.1.0.3.0:common successfully loaded
INFO: Aggregate Description OuiConfigVariables:1.0.0.0.0:common successfully loaded
INFO: Successfully returning from CfmFactory.connect()
INFO: Cfm.save() was called
INFO: Cfm.save(): 2 aggregate instances saved
INFO: oracle.sysman.top.agent:IAction.perform() was called on {Action state:configuration in CfmAggregateInstance: oracle.sysman.top.agent:12.1.0.3.0:common:family=CFM:oh=/users/ncgf/em_agent/core/12.1.0.3.0:label=1}
INFO: Framework waiting for Action to complete at 15:08:10.272
INFO: CfwProgressMonitor:actionProgress:About to perform Action=configuration Status=is running with ActionStep=0 stepIndex=0 microStep=0
WARNING: Skipping environment variable line: "}": oracle.sysman.emCfg.common.CfwException: A non-empty environment line must contain "=": }
WARNING: Failed to read environment variable file /users/ncgf/em_agent/core/12.1.0.3.0/install/envVars.properties: java.io.FileNotFoundException: /users/ncgf/em_agent/core/12.1.0.3.0/install/envVars.properties (No such file or directory)
INFO: oracle.sysman.top.agent:About to execute plug-in Agent Configuration Assistant
INFO: oracle.sysman.top.agent:The plug-in Agent Configuration Assistant is running
INFO: oracle.sysman.top.agent:Internal PlugIn Class: oracle.sysman.agent.config.AgentConfiguration
INFO: oracle.sysman.top.agent:Classpath = /users/ncgf/em_agent/core/12.1.0.3.0/oui/jlib/srvm.jar:/users/ncgf/em_agent/core/12.1.0.3.0/jlib/agentConfig.jar:/users/ncgf/em_agent/core/12.1.0.3.0/jlib/emConfigInstall.jar:/users/ncgf/em_agent/core/12.1.0.3.0/sysman/jlib/emagentSDK.jar:/users/ncgf/em_agent/core/12.1.0.3.0/modules/oracle.http_client_11.1.1.jar:/users/ncgf/em_agent/core/12.1.0.3.0/sysman/jlib/log4j-core.jar
INFO: oracle.sysman.top.agent:AgentConfiguration:agent configuration has been started
INFO: oracle.sysman.top.agent:Parametes passed to agent configuration are:
1.ORACLE_HOME=/users/ncgf/em_agent/core/12.1.0.3.0
2.AGENT_PORT=3872
3.ORACLE_HOSTNAME=nsn175-89.us.oracle.com
4.b_doDiscovery=false
5.AGENT_BASE_DIR=/users/ncgf/em_agent
6.AGENT_INSTANCE_HOME=/users/ncgf/em_agent/agent_inst
7.s_hostname=nsn175-89.us.oracle.com
8.OMS_HOST=nsn175-105.us.oracle.com
9.b_startAgent=false
10.b_secureAgent=true
11.b_chainedInstall=false
12.b_forceConfigure=false
13.EM_UPLOAD_PORT=4904
14.b_forceAgentDefaultPort=false
15.s_staticPorts=
16.PROPERTIES_FILE=
b_skipValidation=false
INFO: oracle.sysman.top.agent:Validating OMS_HOST and EM_UPLOAD_PORT
INFO: oracle.sysman.top.agent:Validating with http protocol ...
INFO: oracle.sysman.top.agent:URL framed is:http://nsn175-105.us.oracle.com:4904/empbs/genwallet
SEVERE: oracle.sysman.top.agent:Connection refusedUnexpected end of file from server
INFO: oracle.sysman.top.agent:Validating with https protocol ...
INFO: oracle.sysman.top.agent:URL framed is:https://nsn175-105.us.oracle.com:4904/empbs/genwallet
SEVERE: oracle.sysman.top.agent:The EM_UPLOAD_PORT passed is a secure port. Hence AGENT_REGISTRATION_PASSWORD or s_encrSecurePwd should be passed
INFO: oracle.sysman.top.agent:EM Protocol Switch determined: https
INFO: oracle.sysman.top.agent:Performing free port detection..
INFO: oracle.sysman.top.agent:Trying for host : nsn175-89/10.134.175.89 and port : 3872
INFO: oracle.sysman.top.agent: Trying for host : /127.0.0.1 and port : 3872
INFO: oracle.sysman.top.agent:** Agent Port Check completed successfully.**
INFO: oracle.sysman.top.agent:Agent Port from User Passed Port3872
INFO: oracle.sysman.top.agent:Paths after canonical format conversions are :
1. state_dir=/users/ncgf/em_agent/agent_inst
2. agentBaseDir=/users/ncgf/em_agent
3. oraHome=/users/ncgf/em_agent/core/12.1.0.3.0
INFO: oracle.sysman.top.agent:Parent directory of agent instance home:/users/ncgf/em_agent
INFO: oracle.sysman.top.agent:AgentConfiguration:perform:AgentPortHandler for /users/ncgf/em_agent/core/12.1.0.3.0 and hosts=nsn175-89.us.oracle.com returned Port to Use=3872
INFO: oracle.sysman.top.agent:Instantiating emctl.template file #DEFAULT_EMSTATE# with /users/ncgf/em_agent/agent_inst
INFO: oracle.sysman.top.agent:Writing the following contents into /users/ncgf/em_agent/core/12.1.0.3.0/install/oragchomelist
INFO: oracle.sysman.top.agent:/users/ncgf/em_agent/core/12.1.0.3.0:/users/ncgf/em_agent/agent_inst
INFO: oracle.sysman.top.agent:Both /etc/oragchomelist and /var/opt/oracle/oragchomelist does not exist.
INFO: oracle.sysman.top.agent:Executing emctl deploy agent command...
INFO: oracle.sysman.top.agent:AgentConfiguration: Executing emctl deploy agent command...
INFO: oracle.sysman.top.agent:Executing the command: /users/ncgf/em_agent/core/12.1.0.3.0/bin/emctl deploy agent -L -o nsn175-105.us.oracle.com:4904 -N /users/ncgf/em_agent/agent_inst nsn175-89.us.oracle.com:3872 nsn175-89.us.oracle.com
INFO: oracle.sysman.top.agent:Creating shared install...
INFO: oracle.sysman.top.agent:Source location: /users/ncgf/em_agent/core/12.1.0.3.0
INFO: oracle.sysman.top.agent:Destination (shared install) : /users/ncgf/em_agent/agent_inst
INFO: oracle.sysman.top.agent:Secure Mode: No
INFO: oracle.sysman.top.agent:DeployMode : agent
INFO: oracle.sysman.top.agent:
INFO: oracle.sysman.top.agent:Creating directories...
INFO: oracle.sysman.top.agent:Creating private.properties...
INFO: oracle.sysman.top.agent:Creating blackouts.xml...
INFO: oracle.sysman.top.agent:Creating targets.xml...
INFO: oracle.sysman.top.agent:Creating emctl control program...
INFO: oracle.sysman.top.agent:Creating emtgtctl control program...
INFO: oracle.sysman.top.agent:Agent will not be secured.
INFO: oracle.sysman.top.agent:Secure REPOSITORY_URL found. New agent should be configured for secure mode
INFO: oracle.sysman.top.agent:Secure emdWalletSrcUrl found. New agent should be configured for secure mode
INFO: oracle.sysman.top.agent:Oracle Enterprise Manager Cloud Control 12c Release 3
INFO: oracle.sysman.top.agent:Copyright (c) 1996, 2013 Oracle Corporation. All rights reserved.
INFO: oracle.sysman.top.agent:Property 'agentTZRegion' is missing from /users/ncgf/em_agent/agent_inst/sysman/config/emd.properties. Updating it...
INFO: oracle.sysman.top.agent:An agentTZregion of 'US/Pacific' is installed in /users/ncgf/em_agent/agent_inst/sysman/config/emd.properties.
INFO: oracle.sysman.top.agent:The command: /users/ncgf/em_agent/core/12.1.0.3.0/bin/emctl deploy agent -L -o nsn175-105.us.oracle.com:4904 -N /users/ncgf/em_agent/agent_inst nsn175-89.us.oracle.com:3872 nsn175-89.us.oracle.com completed with status=0
SEVERE: oracle.sysman.top.agent:Securing of agent step will be skipped because of the following reasons:
1. Agent Registration Password was not passed.
2. b_secureAgent was passed as false
3. The flag -forceConfigure was assed from agentDeploy.sh
INFO: oracle.sysman.top.agent:Plugin File:/users/ncgf/em_agent/plugins.txt
INFO: oracle.sysman.top.agent:Plugin Homes found.
INFO: oracle.sysman.top.agent:Executing command :/users/ncgf/em_agent/core/12.1.0.3.0/perl/bin/perl /users/ncgf/em_agent/core/12.1.0.3.0/bin/AgentPluginDeploy.pl -oracleHome /users/ncgf/em_agent/core/12.1.0.3.0 -agentDir /users/ncgf/em_agent -pluginIdsInfoFile /users/ncgf/em_agent/plugins.txt -action configure -emStateDir /users/ncgf/em_agent/agent_inst
INFO: oracle.sysman.top.agent:
INFO: oracle.sysman.top.agent:
INFO: oracle.sysman.top.agent:The Agent emStateDir location passed is /users/ncgf/em_agent/agent_inst
INFO: oracle.sysman.top.agent: The log file is /users/ncgf/em_agent/agent_inst/install/logs/agentplugindeploy_2013_10_16_15_08_11.log
INFO: oracle.sysman.top.agent: The temp file created to check R/W permissions in Oraclehome: /users/ncgf/em_agent/core/12.1.0.3.0 is /users/ncgf/em_agent/core/12.1.0.3.0/rwFile
INFO: oracle.sysman.top.agent:Plugin command completed with status=0
INFO: oracle.sysman.top.agent:Executing command :/users/ncgf/em_agent/agent_inst/bin/emctl listplugins agent -type all
INFO: oracle.sysman.top.agent:Oracle Enterprise Manager Cloud Control 12c Release 3
INFO: oracle.sysman.top.agent:Oracle Enterprise Manager Cloud Control 12c Release 3
INFO: oracle.sysman.top.agent:Copyright (c) 1996, 2013 Oracle Corporation. All rights reserved.
INFO: oracle.sysman.top.agent:Copyright (c) 1996, 2013 Oracle Corporation. All rights reserved.
INFO: oracle.sysman.top.agent:---------------------------------------------------------------
INFO: oracle.sysman.top.agent:---------------------------------------------------------------
SEVERE: oracle.sysman.top.agent:ERROR: The Management Agent configuration failed. The plug-in configuration for the oracle.sysman.oh monitoring plug-in may have failed, or this plug-in may not be present in the Management Agent software. Ensure that the Management Agent software has the oracle.sysman.oh monitoring plug-in, if not then retry the operation. If the agent software has the oracle.sysman.oh monitoring plug-in, view the plug-in deployment log /users/ncgf/em_agent/agent_inst/install/logs to check if the plug-in configuration for the oracle.sysman.oh monitoring plug-in failed.
SEVERE: oracle.sysman.top.agent:Agent configuration has failed
INFO: oracle.sysman.top.agent:AgentConfiguration:agent configuration finished with status = false
INFO: oracle.sysman.top.agent:AgentConfiguration:agent configuration finished with status = false
INFO: oracle.sysman.top.agent:The plug-in Agent Configuration Assistant has failed its perform method
INFO: Cfm.save() was called
INFO: Cfm.save(): 2 aggregate instances saved
INFO: done waiting for Action from 15:08:10.272
Thank you for your help AkankshaSheoranKaler. I have executed the following command based on your request. If there is any issue, please let me know. Thanks!
"Can you run this command to make sure that the agents bits were downloaded correctly : oms home /bin /emcli verify_updates
Share the output of the command. I am suspecting this is a know issue (Bug 17300008) but i will wait for your output. Also if you can open an SR with oracle support to track this issue and its resolution. "
[ncgf@nsn175-105 bin]$ ./emcli setup -url=https://nsn175-105.us.oracle.com:7803/em -u sername=SYSMAN
Oracle Enterprise Manager 12c 3.
Copyright (c) 1996, 2013 Oracle Corporation and/or its affiliates. All rights reserve d.
The configuration directory "/users/ncgf" may not be local. See the "dir" option in t he help for the setup command.
Do you want to continue using this directory? [yes/no] yes
Enter password
Emcli setup successful
[ncgf@nsn175-105 bin]$ ./emcli verify_updates
Verifying updates. Starting validation...
Type       : Plug-in
Description: Demo Hostsample Test Plugin
Attributes
        Version: 1201000100
        Revision: 0
        OS Platform: Generic Platform
        Plug-in Name: Demo Host Sample Plugin
Archives are missing from the Software Library. Unable to determine the URL for downloading the update. The update might not have come from Oracle Enterprise Manager Store.
For each update with missing archives, emcli import_update can be used with a -force option to re-upload the archives to the Software Library.

   Hello AkankshaSheoranKaler
We have done the following, but we aren't able to resolve this issue. Thank you for your help!
lf
“This happen if the software library is not accessible, readable or unmounted (if it is in shared file system).”
On Enterprise Manager server [nsn175-105], we did the following:
1. we modified /etc/exports to include this line: /export *(rw,no_root_squash,sync)
we start nfs service by executing command “service nfs start”.
On Management Agent server (nsn175-89), we verified that we are able to mount /export directory of EM server.
On Management Agent server, we started firefox browser and were able to run successfully https://nsn175-105.us.oracle.com:4904/empbs/genwallet
After making this change, we ran agent deployment again. We encountered the same error as shown above.
“You can fix the software library or you can download the agent bits in offline mode.”
For fixing the software library, select Setup->Provision and Patching->Offline Patching, then select Offline Patching radio button, download: https://updates.oracle.com/download/em_catalog.zip. Next upload this zip file.
“Try downloading the bits again”
We are not sure what agent bits are. Would you please explain this and provide procedure how we can download this?
(Here I have attempted to fix the software library, but I am new to Enterprise Manager and not sure how to interpret this).

How to install and configure Eclipse???

Can any one guide me how to install and configure Eclipse to use it with jdk 1.5??

how to install eclipse?
you don't need to install eclipse just extract it to a specific path...
install j2se 1.5 then eclipse will automatically detect it...

SAP Personas: An unexpected behaviour has been detected and you have been disconnected – please log in again.

Hallo everyone,
We are installing Personas and facing several challenges.
Personas 2 SP02 was installed according to instructions of Note '1848339 - Installation and Upgrade note for Personas' and configured according to the Config Guide v1.3 (rel. May 2014). The referenced notes were also applied as well as the 'How to config - FAQ' blog by Sushant.
We are able to log on and execute transactions and perform activities successfully (e.g. SE80, SPRO, KB15, etc.).
When trying to copy a screen the following error appears: 'An unexpected behaviour has been detected and you have been disconnected - please log in again.'
Thereafter one can simply continue executing transactions without having to log in again.
Please see the download of the error attached as per blog: SAP Screen Personas Support Tips – client side logging
The HAR is unfortunately too large to attach. Are there any alternatives?
Thank you in advance for you assistance!
Kind regards,
Daniel
Message was edited by: Daniel K

Hi,
I have never worked on SAP PERSONA but you can try below things
1)try to use different user or J2ee_admin since it might be same user multiple session case
2) Try with different browser since plugins can behave unexpectedly
3)Make entry in host file also
4) check dev_icm logs
5) check on ABAP side for dumps in ST22
Warm Regards,
Sumit

%IP-3-LOOPPAK: Looping packet detected and dropped -

Hello All,
Recenlty we have upgraded the IOS from c2800nm-ipvoicek9-mz.124-15.T14.bin to c2800nm-ipvoicek9-mz.151-4.M8.bin. After that the gateways are hitting the below error message. The src IP is voice gateway IP address and dst IP is muliticast MOH IP configured under call manager fall back. Assistance are much appreciated..
%IP-3-LOOPPAK: Looping packet detected and dropped -
src=10.0.XXX.XXX, dst=239.X.XXX.254, hl=20, tl=116, prot=17, sport=16803, dport=16385
in=local, nexthop=239.X.XXX.254, out=GigabitEthernet0/0
options=none -Process= "VOIP_RTCP", ipl= 0, pid= 299
-Traceback= 425C9758z 425CAA30z 425CBBFCz 425CC0D4z 425CD214z 425CD524z 425CD590z 42AC4178z 43AA20DCz 43AA9B44z 437F3094z 437F3078z
Thanks
Murali

CSCtn83520 is a suspect but you are already on an IOS version that contains the fix to this defect.
Are you facing any issues with calls or MOH?

Detecting (And Killing) Abandoned Threads

Hi All,
I'm going to try to make my question as simple as possible: I'm trying to use the service guardian to automatically detect an abandoned thread and kill the originating process. So basically I set up a test that ends up with an abandoned thread and configured service Guardian... but it didn't work :D
What I first did is setting the guardian's timeout to be very short (6 seconds). When I do that, what I get is:
2010-03-26 10:03:29.389/0.859 Oracle Coherence GE 3.5.3/465 <Info> (thread=main, member=n/a): Loaded cache configuration from "file:/C:/workspaces/POC/InvocableTest/bin/coherence-cache-config.xml"
2010-03-26 10:03:29.952/1.422 Oracle Coherence GE 3.5.3/465 <D5> (thread=Cluster, member=n/a): Service Cluster joined the cluster with senior service member n/a
2010-03-26 10:03:35.295/6.765 Oracle Coherence GE 3.5.3/465 <Error> (thread=Cluster, member=n/a): Attempting recovery (due to soft timeout) of Guard{Daemon=TcpRingListener}
2010-03-26 10:03:35.904/7.374 Oracle Coherence GE 3.5.3/465 <Error> (thread=Cluster, member=n/a): Terminating guarded execution (due to hard timeout) of Guard{Daemon=TcpRingListener}
Coherence <Error>: Halting JVM due to unrecoverable service failure
2010-03-26 10:03:36.904/8.374 Oracle Coherence GE 3.5.3/465 <Error> (thread=Termination Thread, member=n/a): Full Thread Dump
ThreadCluster
     java.lang.Object.wait(Native Method)
     com.tangosol.coherence.component.util.Daemon.onWait(Daemon.CDB:18)
     com.tangosol.coherence.component.util.daemon.queueProcessor.service.Grid.onWait(Grid.CDB:6)
     com.tangosol.coherence.component.util.Daemon.run(Daemon.CDB:39)
     java.lang.Thread.run(Unknown Source)
So that's before the thread gets abandoned... it seems that it detects a deadlock when starting coherence. But that's ok, I know the service guardian is working. The problem comes when I set the timeout to something more realistic: 35 seconds for instance. I run my test, the thread gets to an abandoned state and the service guardian does not see it :(
Any Ideas?
h4. My override config is:
<coherence>
<cluster-config>
     <service-guardian>
          <timeout-milliseconds system-property="tangosol.coherence.guard.timeout">6000</timeout-milliseconds>
          <service-failure-policy>exit-process</service-failure-policy>
     </service-guardian>
</cluster-config>
<logging-config>
<severity-level system-property="tangosol.coherence.log.level">5</severity-level>
<character-limit system-property="tangosol.coherence.log.limit">0</character-limit>
</logging-config>
</coherence>
Thanks!
Fernando
Edited by: ZeoS on Mar 26, 2010 7:13 AM

it's an Invovable running on the server.
The description in the debugger is: InvocationServiceWorker
Maybe this helps:
10-03-26 12:03:41.279/72.663 Oracle Coherence GE 3.5.3/465 <Error> (thread=Abandon, member=1): A worker thread "InvocationServiceWorker:0 executing task "Message "InvocationRequest"
FromMember=Member(Id=1, Timestamp=2010-03-26 12:02:29.866, Address=10.31.106.86:8088, MachineId=32598, Location=site:someSite.com,machine:ZeoSWorkStation,process:1084, Role=TestInvocableExpiration)
FromMessageId=0
Internal=false
MessagePartCount=0
PendingCount=0
MessageType=1
ToPollId=0
Poll=null
Packets
Service=InvocationService{Name=InvocationService, State=(SERVICE_STARTED), Id=3, Version=3.1, OldestMemberId=1}
ToMemberSet=MemberSet(Size=1, BitSetCount=2, ids=[1])
NotifySent=false
InvocationRequest{Query, Task=TestInvocableExpiration.SocketInvocable@16b352c}
}", did not respond to 8 interrupt requests. The execution was canceled. The thread is abandoned...
Fernando

Diff b/w alert Categories and configurations

Hi Experts,
Could you please help me here, what is diff b/w Alert Categories and configurations.
Ans also what is the use of Container elements in Categories.
You ans is very helpful for me.
Thanks in Advance all.
Regards,
Madhu.

Hi Madhu,
In Alert configuration alert rules are defined based on Alert Categories. So Alert Categories has defined using t code ALRTCATDEF. Container Elements fetches the appropriate dynamic message base on the container variable.
Go through the below doc:
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/00e97ba2-85ce-2b10-20bc-bc05cd172154?QuickLink=index&…
Regards,
Krupa

I have LabView but I do not have the Calibration and Configuration Palette,and I could not download it, how can I download it or if i cannot,can I work with the NI-DAQ Calibration_1200?

I have read in a tutorial for the board 1200 that I can calibrate it with the Calibration and Configuration Palette in LabVIEW, but I do not have them and I could not download it to access its libraries, so I can only download the NI-DAQ software,What's my best choice and if it is to download the palette with its libraries, how can download it with them?I'd appreciate your answers

If you wish to use your 1200 device in LabVIEW, you must download and install NI-DAQ. When you install NI-DAQ, it will ask you if you would like to install support for LabVIEW. By installing this support, you will then have access to the DAQ pallette in LabVIEW. The DAQ pallette requires that you have NI-DAQ installed.
For more information on installing and using your device, you can refer to the DAQ Quick Start Guide. You can download it from:
http://digital.ni.com/manuals.nsf/14807683e3b2dd8f8625677b006643f0/0eca53fe80911b1f862568560068295d
Regards,
Erin

How to properly create and configure SharePoint 2013 Search service with PowerShell?

Hello Forum,
I have installed SharePoint 2013 across three tier servers:
WFE Server (Of course, SharePoint is installed here. Bsically this is just a Web server)
APP Server (Of course, SharePoint is installed here + Central Admin + Service Apps).
SQL Server
I now want to create and configure the Search service, obviously on the APP Server, But of course the search functionality should work correctly on the WFE server to.
I want to do this via a proper PowerShell script. I found Spence Harbar's script on: (http://www.harbar.net/articles/sp2013mt.aspx), But it has three problems, and they are as follows:
1) Spence Harbar himself literally stated on his article that this script is for: "deploying on a single server farm", But what if I have three tier servers? Could anyone please help me out in suggesting the required tweaks in the
script?
2) By default Search uses the SP_Farm account, So, How can I change the script to use other dedicated account for the search service e.g. SP_SearchAcc ?
3) How can I modify the script to specify a default Search center?
4) Apart from all the three aforementioned point - Is the script missing anything?
I would greatly appreciate your inputs - Thanks !

the only differences are where you place the components. if you are doing a small server farm with a 1-1-1, most likely you just need to change the script so that you set the index and query processing component on the front end, but the others on
the app server. just a 2 second update... just keep in mind this will work, but I am making several assumptions without any knowledge of your farm, users, capabilities.
generally, there would be more of a breakout on the topology than that, but im guessing for this farm that you wont have dedicated search servers. also, a lot depends on # users (rps really), # items in index, size of VMs (RAM for query processing,
Disk for index, etc, etc), and making sure the topology works for your particular environment and needs.
if you want more detailed topology help, which aligns as closely as possible to "best practices" (not that those exist in SharePoint, go ahead and provide the total # users, average/peak RPS for search, current index size, content source types,
VM specs RAM, CPU, #/Size of drives, HA concerns/priority (obviously isn't, since only 1-1-1)
Christopher Webb | MCM: SharePoint 2010 | MCSM: SharePoint Charter | MCT | http://christophermichaelwebb.com

VCenter SRM Installation and Configuration

Hello,
We have installed and configured SRM 5.5.1 in Main site and DR site. In DR site we have two hosts and no shared storage.
Each have one vsphere replication appliance deployed and both the sites connected and we have also replicated two virtual machines successfully.
Next step we have configured protection group and recovery plan as well.
But when we test a recovery plan it gives a error "unable to access virtual machine configuration file"
Is it necessary we must have a shared storage? Can't we use local datastore on each host to power on the machines.
Regards
Karthik

Hi,
No, shared storage is not required:
Array/ vendor types
Requires same storage replication solution at both sites (eg. EMC RecoverPoint, NetApp vFiler, IBM SVC, etc)
Can support any storage solution at either end including local storage as long as it is covered by the vSphere HCL
SRM - Array Based Replication vs. vSphere Replication | VMware vSphere Blog - VMware Blogs
Michael.

Ibase and configuration error while creating a Service Contract

Hi,
I am creating a Service Contract programatically and not manually through the T-code CRMD_ORDER.
I am using the Function module CRMXIF_ORDER_SAVE for the same as the FM BAPI_BUSPROCESSND_CREATEMULTI and CRM_ORDER_MAINTAIN did not work for me because of the number of parameters that needs to be passed for creating the Service contract.
The Service contract does get created but there are errors corresponding to the Point of delivery and configuration missing.
The error corresponding to the point of delivery says "IS-U:allocate a point of delivery to the item" even though I am passing the values in the REF_OBJECTS field of the CRMXIF_BUSTRANS_ITEM structure.
Structure for the same is :
ls_objects_i-TYPE_REF_OBJ = 'B'.
ls_objects_i-object_task = 'I'.
ls_objects_i-PRODUCT_GUID = lv_product_guid.
ls_objects_i-PRODUCT_ID = p_product_id.
ls_objects_i-IBASE_COMP_GUID = ls_output-IBASE_GUID.
ls_objects_i-IB_INSTANCE = 1582.
ls_objects_i-IB_COMP_VALID = '20070926093651'.
ls_objects_i-SERIAL_NUMBER = '0102 46CC9C278B92025BE10000000AD5920E'.
append ls_objects_i to lt_objects_i.
p_ls_item-REF_OBJECT-data = lt_objects_i.
p_ls_item-REF_OBJECT-datax = 'X'.
Similarly,the error for the configuration says "Configuration for the item missing" and here again I am passing the values in the CONFIGURATION structure.
Structure for this is :
p_ls_item-configuration-data-consist = 'T'.
p_ls_item-configuration-data-kbname = 32.
p_ls_item-configuration-data-kbvers = '0.0'.
p_ls_item-configuration-data-kbprofile = 'E_H_B'.
p_ls_item-configuration-data-complete = 'T'.
p_ls_item-configuration-data-spras = 'E'.
p_ls_item-configuration-data-cfginfo = 'VCOND=VARIANT_CONDITION_KEY'
ls_cuins-OBJ_TYPE = 'SERV'.
ls_cuins-class_type = 300.
ls_cuins-obj_key = 'E_H_B'.
ls_cuins-obj_txt = 'E_H_B'.
ls_cuins-QUANTITY = '1.0'.
ls_cuins-COMPLETE = 'T'.
ls_cuins-CONSIST = 'T'.
append ls_cuins to lt_cuins.
ls_config_i-instance = lt_cuins.
p_ls_item-configuration-data = ls_config_i.
p_ls_item-configuration-datax = 'X'.
clear ls_config_i.
ls_cuval-charc = 'DISCOUNT_EUR'.
ls_cuval-charc_txt = 'DISCOUNT_EUR'.
ls_cuval-value = '0.0'.
ls_cuval-value_txt
append ls_cuval to lt_cuval.
ls_instance-value = lt_cuval.
insert ls_instance into table lt_instance.
ls_config_i-instance = lt_instance.
p_ls_item-configuration-data = ls_config_i.
p_ls_item-configuration-datax = 'X'.
clear ls_config_i.
Kindly help if anyone has worked on this.......
Regards,
Puneet Jhari.

Hi,
I am creating a Service Contract programatically and not manually through the T-code CRMD_ORDER.
I am using the Function module CRMXIF_ORDER_SAVE for the same as the FM BAPI_BUSPROCESSND_CREATEMULTI and CRM_ORDER_MAINTAIN did not work for me because of the number of parameters that needs to be passed for creating the Service contract.
The Service contract does get created but there are errors corresponding to the Point of delivery and configuration missing.
The error corresponding to the point of delivery says "IS-U:allocate a point of delivery to the item" even though I am passing the values in the REF_OBJECTS field of the CRMXIF_BUSTRANS_ITEM structure.
Structure for the same is :
ls_objects_i-TYPE_REF_OBJ = 'B'.
ls_objects_i-object_task = 'I'.
ls_objects_i-PRODUCT_GUID = lv_product_guid.
ls_objects_i-PRODUCT_ID = p_product_id.
ls_objects_i-IBASE_COMP_GUID = ls_output-IBASE_GUID.
ls_objects_i-IB_INSTANCE = 1582.
ls_objects_i-IB_COMP_VALID = '20070926093651'.
ls_objects_i-SERIAL_NUMBER = '0102 46CC9C278B92025BE10000000AD5920E'.
append ls_objects_i to lt_objects_i.
p_ls_item-REF_OBJECT-data = lt_objects_i.
p_ls_item-REF_OBJECT-datax = 'X'.
Similarly,the error for the configuration says "Configuration for the item missing" and here again I am passing the values in the CONFIGURATION structure.
Structure for this is :
p_ls_item-configuration-data-consist = 'T'.
p_ls_item-configuration-data-kbname = 32.
p_ls_item-configuration-data-kbvers = '0.0'.
p_ls_item-configuration-data-kbprofile = 'E_H_B'.
p_ls_item-configuration-data-complete = 'T'.
p_ls_item-configuration-data-spras = 'E'.
p_ls_item-configuration-data-cfginfo = 'VCOND=VARIANT_CONDITION_KEY'
ls_cuins-OBJ_TYPE = 'SERV'.
ls_cuins-class_type = 300.
ls_cuins-obj_key = 'E_H_B'.
ls_cuins-obj_txt = 'E_H_B'.
ls_cuins-QUANTITY = '1.0'.
ls_cuins-COMPLETE = 'T'.
ls_cuins-CONSIST = 'T'.
append ls_cuins to lt_cuins.
ls_config_i-instance = lt_cuins.
p_ls_item-configuration-data = ls_config_i.
p_ls_item-configuration-datax = 'X'.
clear ls_config_i.
ls_cuval-charc = 'DISCOUNT_EUR'.
ls_cuval-charc_txt = 'DISCOUNT_EUR'.
ls_cuval-value = '0.0'.
ls_cuval-value_txt
append ls_cuval to lt_cuval.
ls_instance-value = lt_cuval.
insert ls_instance into table lt_instance.
ls_config_i-instance = lt_instance.
p_ls_item-configuration-data = ls_config_i.
p_ls_item-configuration-datax = 'X'.
clear ls_config_i.
Kindly help if anyone has worked on this.......
Regards,
Puneet Jhari.

Install and configure report service on Oracle Application Server 10g

i want to know how to install and configure report service on Oracle Application Server 10g Release 3 (10.1.3.1.0)
Thanks

the case is that we developed an ADF Application, so we want to deploy it on the latest version of Oracle Application server.
our application communicate with Oracle reports (run oracle reports from our Application) as there are no Oracle report products for JEE Application.
so if there are not report service that can run on Oracle Application Server 10g Release 3 (10.1.3.1.0),
what is the other choices that oracle supports that can help us in this case ???

EIS Installation and Configuration

Hi Everybody,
I am trying to install EIS 9.31 on my laptop (i.e Win2k3 Server), I have successfully installed Essbase and EIS
But I have no idea how to configure(Creating DSN Catalog) in EIS.
I am using Oracle 10g. Can any one please help me on thsi installation.
Already I gone through the installation document but I didn't understand how to configure.
If anyone having installation and Configuring Screen shots please send me to my mail
Mail Id: [email protected]
This is very urgent I need to give presentation on the EIS
Thanks in Advance for your help
Awaiting for your quick Response

I'm not sure what version of software you are looking to install, but for 9.3.1, we just installed our application server (Weblogic), installed Shared Services, supplied the database info and we were good to go. I do believe; however, your mileage will vary depending on the application server you use as some of them have an option for 'automatic' installation and some are manual. (I went the 'automatic' route) You will need to refer to the installation documentation for all of the relevant details, though.

What is BDI or BDS spelled out? Jabber for Mac 9.2(1) Installation and Configuration Guide

I’m spending the day catching up on Jabber/IM&P release notes across the server/clients.
So I’m used to EDI and UDS, but we have a new acronym in the Jabber for Mac 9.2(1) Installation and Configuration Guide called BDI and BDS. However they don’t define what BDI stands for other than BDI is LDAP for non-windows
Clients and suggests it should be used for Jabber for Mac.
What is BDI or BDS spelled out? Something directory integration, but what is the B ?
Then to add to the mix they reference BDS which sounds like the old UDS (is UDS changing to BDS?)
How can Jabber get any more confusing…
I also noted in the Jabber Video for iPad 9.3.4 release notes that Apple is removing the Always Connect option in the near future. Manually launching Cisco AnyConnect Secure Mobility Client before making a call. This is going to upset some customers who like how Lync uses https and just works from anywhere with enhanced directory integration…

Basic Directory Integration. It's not new, we had it in the Windows clients as far back as CUPC. The distinction got introduced when EDI was introduced, relying on Windows ADSI APIs instead of the client making a native LDAP bind.
To my knowledge BDI/BDS are the same thing; I'm guessing S is 'service'. UDS remains unchanged.
I also noted in the Jabber Video for iPad 9.3.4 release notes that Apple is removing the Always Connect option in the near future.
Well, they lost a patent infringement lawsuit and chose to change the functionality instead of pay the troll. That's not Jabber's fault. Collaboration Edge will be the way to avoid this in the near future.
Please remember to rate helpful responses and identify helpful or correct answers.

Detecting and configuring a Bosch G-Sensor accelerometer

Similar Messages

Maybe you are looking for