Dhcpcd-based network fails during boot

Hi,
My fully updated Arch_X86-64/KDE is connected to the Internet router via (on-board wired) eth1, and is configured to get an auto IP address.
This has worked flawlessly for years till two days ago.
Ever since,  eth1 service fails during boot, and requires several manual dhcpcd command to finally kick in. The same applies after waking from sleep mode. (see terminal output below)
As can be seen the system is configured to load the (correct) r8169 mode.
Please advise.
Thanks
Miki Badt
---------copy of respective commands---------------
# journalctl -b | grep eth
Sep 15 15:50:17 Miki_Arch systemd[1]: Expecting device sys-subsystem-net-devices-eth1.device...
Sep 15 15:50:17 Miki_Arch systemd[1]: Expecting device sys-subsystem-net-devices-eth0.device...
Sep 15 15:50:17 Miki_Arch kernel: r8169 0000:05:00.0 eth0: RTL8168d/8111d at 0xffffc900119d2000, 6c:f0:49:ed:b3:e9, XID 083000c0 IRQ 49
Sep 15 15:50:17 Miki_Arch kernel: r8169 0000:05:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
Sep 15 15:50:17 Miki_Arch kernel: r8169 0000:06:00.0 eth1: RTL8168d/8111d at 0xffffc900119e6000, 6c:f0:49:ed:b3:eb, XID 083000c0 IRQ 50
Sep 15 15:50:17 Miki_Arch kernel: r8169 0000:06:00.0 eth1: jumbo features [frames: 9200 bytes, tx checksumming: ko]
Sep 15 15:50:23 Miki_Arch dhcpcd[339]: eth1: waiting for carrier
Sep 15 15:50:23 Miki_Arch dhcpcd[336]: eth0: waiting for carrier
Sep 15 15:50:29 Miki_Arch kernel: r8169 0000:06:00.0 eth1: link down
Sep 15 15:50:29 Miki_Arch kernel: r8169 0000:06:00.0 eth1: link down
Sep 15 15:50:29 Miki_Arch kernel: IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Sep 15 15:50:29 Miki_Arch kernel: r8169 0000:05:00.0 eth0: link down
Sep 15 15:50:29 Miki_Arch kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Sep 15 15:50:53 Miki_Arch systemd[1]: [email protected]: control process exited, code=exited status=1
Sep 15 15:50:53 Miki_Arch systemd[1]: Failed to start dhcpcd on eth0.
Sep 15 15:50:53 Miki_Arch systemd[1]: Unit [email protected] entered failed state.
Sep 15 15:50:53 Miki_Arch systemd[1]: [email protected]: control process exited, code=exited status=1
Sep 15 15:50:53 Miki_Arch systemd[1]: Failed to start dhcpcd on eth1.
Sep 15 15:50:53 Miki_Arch systemd[1]: Unit [email protected] entered failed state.
#manual commands
[root@Miki_Arch miki]# dhcpcd eth1
dhcpcd[1039]: version 6.0.5 starting
dhcpcd[1039]: eth1: waiting for carrier
dhcpcd[1039]: timed out
dhcpcd[1039]: exited
[root@Miki_Arch miki]# ping www.ynet.co.il
ping: unknown host www.ynet.co.il
[root@Miki_Arch miki]# dhcpcd eth1
dhcpcd[1046]: version 6.0.5 starting
dhcpcd[1046]: eth1: soliciting an IPv6 router
dhcpcd[1046]: eth1: rebinding lease of 192.168.1.13
dhcpcd[1046]: eth1: leased 192.168.1.13 for 3600 seconds
dhcpcd[1046]: eth1: adding host route to 192.168.1.13 via 127.0.0.1
dhcpcd[1046]: eth1: adding route to 192.168.1.0/24
dhcpcd[1046]: eth1: adding default route via 192.168.1.1
lspci -v | grep Ethernet
05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller (rev 03)
06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller (rev 03)
lspci -k
05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Motherboard
Kernel driver in use: r8169
Kernel modules: r8169
06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Motherboard
Kernel driver in use: r8169
Kernel modules: r8169
cat /etc/modules-load.d/realtek.conf
r8169
Last edited by mibadt (2013-09-15 13:29:25)

Hi,
I've some errors with the new dhcpcd, you should downgrade.
https://wiki.archlinux.org/index.php/Do … g_Packages

Similar Messages

  • Loading Modules and Mounting Local Filesystems failed during boot

    Hi all,
    since 2-3 weeks I've had some FAIL during the boot (after having upgraded the system, I remember that there was involved an upgrade of init script probably, or something connected with the booting process).
    [gianluca@gianluca-laptop ~]$ dmesg
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Linux version 2.6.39-ARCH (thomas@evey) (gcc version 4.6.1 (GCC) ) #1 SMP PREEMPT Sat Jul 9 15:31:04 CEST 2011
    [ 0.000000] BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
    [ 0.000000] BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
    [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    [ 0.000000] BIOS-e820: 0000000000100000 - 000000007ba60000 (usable)
    [ 0.000000] BIOS-e820: 000000007ba60000 - 000000007babf000 (reserved)
    [ 0.000000] BIOS-e820: 000000007babf000 - 000000007bb80000 (usable)
    [ 0.000000] BIOS-e820: 000000007bb80000 - 000000007bbbf000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 000000007bbbf000 - 000000007bbe2000 (usable)
    [ 0.000000] BIOS-e820: 000000007bbe2000 - 000000007bbf7000 (ACPI data)
    [ 0.000000] BIOS-e820: 000000007bbf7000 - 000000007bc00000 (usable)
    [ 0.000000] BIOS-e820: 000000007bc00000 - 0000000080000000 (reserved)
    [ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fed10000 - 00000000fed14000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fed18000 - 00000000fed1a000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    [ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
    [ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
    [ 0.000000] DMI 2.6 present.
    [ 0.000000] DMI: Acer Aspire 1810TZ/JM11-MS, BIOS v1.3314 08/31/2010
    [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
    [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
    [ 0.000000] last_pfn = 0x7bc00 max_arch_pfn = 0x100000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-FFFFF write-through
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 000000000 mask FC0000000 write-back
    [ 0.000000] 1 base 0FFE00000 mask FFFE00000 write-protect
    [ 0.000000] 2 base 040000000 mask FC0000000 write-back
    [ 0.000000] 3 base 07C000000 mask FFC000000 uncachable
    [ 0.000000] 4 base 07BC00000 mask FFFC00000 uncachable
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] initial memory mapped : 0 - 01c00000
    [ 0.000000] Base memory trampoline at [c009a000] 9a000 size 16384
    [ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
    [ 0.000000] 0000000000 - 0000400000 page 4k
    [ 0.000000] 0000400000 - 0037400000 page 2M
    [ 0.000000] 0037400000 - 00377fe000 page 4k
    [ 0.000000] kernel direct mapping tables up to 377fe000 @ 1bfb000-1c00000
    [ 0.000000] RAMDISK: 7b8a0000 - 7ba50000
    [ 0.000000] Allocated new RAMDISK: 3764e000 - 377fdbda
    [ 0.000000] Move RAMDISK from 000000007b8a0000 - 000000007ba4fbd9 to 3764e000 - 377fdbd9
    [ 0.000000] ACPI: RSDP 000fe020 00024 (v02 ACRSYS)
    [ 0.000000] ACPI: XSDT 7bbf6120 0006C (v01 ACRSYS ACRPRDCT 00000001 01000013)
    [ 0.000000] ACPI: FACP 7bbf4000 000F4 (v04 ACRSYS ACRPRDCT 00000001 1025 01000013)
    [ 0.000000] ACPI: DSDT 7bbe8000 073EA (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
    [ 0.000000] ACPI: FACS 7bb8d000 00040
    [ 0.000000] ACPI: DMAR 7bbf5000 00068 (v01 ? 00000001 00000000)
    [ 0.000000] ACPI: HPET 7bbf3000 00038 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
    [ 0.000000] ACPI: APIC 7bbf2000 0006C (v02 ACRSYS ACRPRDCT 00000001 1025 01000013)
    [ 0.000000] ACPI: MCFG 7bbf1000 0003C (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
    [ 0.000000] ACPI: ASF! 7bbf0000 000A5 (v32 ACRSYS ACRPRDCT 00000001 1025 01000013)
    [ 0.000000] ACPI: SLIC 7bbe7000 00176 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
    [ 0.000000] ACPI: BOOT 7bbe6000 00028 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
    [ 0.000000] ACPI: SSDT 7bbe2000 00655 (v01 PmRef CpuPm 00003000 INTL 20051117)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] 1092MB HIGHMEM available.
    [ 0.000000] 887MB LOWMEM available.
    [ 0.000000] mapped low ram: 0 - 377fe000
    [ 0.000000] low ram: 0 - 377fe000
    [ 0.000000] Zone PFN ranges:
    [ 0.000000] DMA 0x00000010 -> 0x00001000
    [ 0.000000] Normal 0x00001000 -> 0x000377fe
    [ 0.000000] HighMem 0x000377fe -> 0x0007bc00
    [ 0.000000] Movable zone start PFN for each node
    [ 0.000000] early_node_map[5] active PFN ranges
    [ 0.000000] 0: 0x00000010 -> 0x0000009e
    [ 0.000000] 0: 0x00000100 -> 0x0007ba60
    [ 0.000000] 0: 0x0007babf -> 0x0007bb80
    [ 0.000000] 0: 0x0007bbbf -> 0x0007bbe2
    [ 0.000000] 0: 0x0007bbf7 -> 0x0007bc00
    [ 0.000000] On node 0 totalpages: 506587
    [ 0.000000] free_area_init_node: node 0, pgdat c14a1980, node_mem_map f66d5200
    [ 0.000000] DMA zone: 32 pages used for memmap
    [ 0.000000] DMA zone: 0 pages reserved
    [ 0.000000] DMA zone: 3950 pages, LIFO batch:0
    [ 0.000000] Normal zone: 1744 pages used for memmap
    [ 0.000000] Normal zone: 221486 pages, LIFO batch:31
    [ 0.000000] HighMem zone: 2185 pages used for memmap
    [ 0.000000] HighMem zone: 277190 pages, LIFO batch:31
    [ 0.000000] Using APIC driver default
    [ 0.000000] ACPI: PM-Timer IO Port: 0x408
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)
    [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
    [ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
    [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
    [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
    [ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:78000000)
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 12 pages/cpu @f6000000 s27648 r0 d21504 u1048576
    [ 0.000000] pcpu-alloc: s27648 r0 d21504 u1048576 alloc=1*4194304
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 502626
    [ 0.000000] Kernel command line: root=/dev/disk/by-uuid/2bef0cce-027d-44fa-a086-056c390cd847 ro quiet
    [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [ 0.000000] Initializing CPU#0
    [ 0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
    [ 0.000000] allocated 8109824 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] ------------[ cut here ]------------
    [ 0.000000] WARNING: at drivers/pci/dmar.c:634 warn_invalid_dmar+0x98/0xb0()
    [ 0.000000] Hardware name: Aspire 1810TZ
    [ 0.000000] Your BIOS is broken; DMAR reported at address 0!
    [ 0.000000] BIOS vendor: INSYDE; Ver: v1.3314; Product Version: v1.3314
    [ 0.000000] Modules linked in:
    [ 0.000000] Pid: 0, comm: swapper Not tainted 2.6.39-ARCH #1
    [ 0.000000] Call Trace:
    [ 0.000000] [<c1046112>] warn_slowpath_common+0x72/0xa0
    [ 0.000000] [<c11e3dd8>] ? warn_invalid_dmar+0x98/0xb0
    [ 0.000000] [<c11e3dd8>] ? warn_invalid_dmar+0x98/0xb0
    [ 0.000000] [<c10461a2>] warn_slowpath_fmt_taint+0x32/0x40
    [ 0.000000] [<c11e3dd8>] warn_invalid_dmar+0x98/0xb0
    [ 0.000000] [<c14cba32>] check_zero_address+0x57/0x12b
    [ 0.000000] [<c12250cd>] ? acpi_get_table_with_size+0x59/0xb3
    [ 0.000000] [<c14cbb18>] detect_intel_iommu+0x12/0x78
    [ 0.000000] [<c14ad67e>] pci_iommu_alloc+0x35/0x5a
    [ 0.000000] [<c14b92c3>] mem_init+0xe/0x26d
    [ 0.000000] [<c14c3396>] ? __alloc_bootmem_node_nopanic+0x72/0x98
    [ 0.000000] [<c1342afc>] ? printk+0x1d/0x1f
    [ 0.000000] [<c14c5183>] ? page_cgroup_init_flatmem+0x8f/0xbc
    [ 0.000000] [<c14a85cc>] start_kernel+0x1a0/0x357
    [ 0.000000] [<c14a81bd>] ? loglevel+0x18/0x18
    [ 0.000000] [<c14a80b3>] i386_start_kernel+0xb3/0xb9
    [ 0.000000] ---[ end trace a7919e7f17c0a725 ]---
    [ 0.000000] Disabling lock debugging due to kernel taint
    [ 0.000000] Initializing HighMem for node 0 (000377fe:0007bc00)
    [ 0.000000] Memory: 1993572k/2027520k available (3376k kernel code, 32776k reserved, 1390k data, 512k init, 1117500k highmem)
    [ 0.000000] virtual kernel memory layout:
    [ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
    [ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    [ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
    [ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
    [ 0.000000] .init : 0xc14a8000 - 0xc1528000 ( 512 kB)
    [ 0.000000] .data : 0xc134c3bf - 0xc14a7c00 (1390 kB)
    [ 0.000000] .text : 0xc1000000 - 0xc134c3bf (3376 kB)
    [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
    [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Preemptable hierarchical RCU implementation.
    [ 0.000000] RCU-based detection of stalled CPUs is disabled.
    [ 0.000000] Verbose stalled-CPUs detection is disabled.
    [ 0.000000] NR_IRQS:512
    [ 0.000000] CPU 0 irqstacks, hard=f540c000 soft=f540e000
    [ 0.000000] Console: colour VGA+ 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] hpet clockevent registered
    [ 0.000000] Fast TSC calibration using PIT
    [ 0.000000] Detected 1296.656 MHz processor.
    [ 0.003337] Calibrating delay loop (skipped), value calculated using timer frequency.. 2594.36 BogoMIPS (lpj=4322186)
    [ 0.003344] pid_max: default: 32768 minimum: 301
    [ 0.003415] Security Framework initialized
    [ 0.003422] AppArmor: AppArmor disabled by boot time parameter
    [ 0.003458] Mount-cache hash table entries: 512
    [ 0.003763] Initializing cgroup subsys ns
    [ 0.003768] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
    [ 0.003772] Initializing cgroup subsys cpuacct
    [ 0.003793] Initializing cgroup subsys memory
    [ 0.003809] Initializing cgroup subsys devices
    [ 0.003813] Initializing cgroup subsys freezer
    [ 0.003816] Initializing cgroup subsys net_cls
    [ 0.003819] Initializing cgroup subsys blkio
    [ 0.003876] CPU: Physical Processor ID: 0
    [ 0.003879] CPU: Processor Core ID: 0
    [ 0.003883] mce: CPU supports 6 MCE banks
    [ 0.003894] CPU0: Thermal monitoring enabled (TM2)
    [ 0.003899] using mwait in idle threads.
    [ 0.005672] ACPI: Core revision 20110316
    [ 0.016682] ftrace: allocating 15225 entries in 30 pages
    [ 0.020059] Enabling APIC mode: Flat. Using 1 I/O APICs
    [ 0.023598] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.056606] CPU0: Genuine Intel(R) CPU U4100 @ 1.30GHz stepping 0a
    [ 0.056663] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
    [ 0.056663] ... version: 2
    [ 0.056663] ... bit width: 40
    [ 0.056663] ... generic registers: 2
    [ 0.056663] ... value mask: 000000ffffffffff
    [ 0.056663] ... max period: 000000007fffffff
    [ 0.056663] ... fixed-purpose events: 3
    [ 0.056663] ... event mask: 0000000700000003
    [ 0.073511] NMI watchdog enabled, takes one hw-pmu counter.
    [ 0.100013] CPU 1 irqstacks, hard=f54f6000 soft=f54f8000
    [ 0.100017] Booting Node 0, Processors #1
    [ 0.100021] smpboot cpu 1: start_ip = 9a000
    [ 0.006666] Initializing CPU#1
    [ 0.196688] NMI watchdog enabled, takes one hw-pmu counter.
    [ 0.203327] Brought up 2 CPUs
    [ 0.203331] Total of 2 processors activated (5188.93 BogoMIPS).
    [ 0.204780] devtmpfs: initialized
    [ 0.204780] PM: Registering ACPI NVS region at 7bb80000 (258048 bytes)
    [ 0.206812] print_constraints: dummy:
    [ 0.206898] NET: Registered protocol family 16
    [ 0.207056] ACPI: bus type pci registered
    [ 0.207200] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
    [ 0.207205] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
    [ 0.207209] PCI: Using MMCONFIG for extended config space
    [ 0.207212] PCI: Using configuration type 1 for base access
    [ 0.207951] bio: create slab <bio-0> at 0
    [ 0.211250] ACPI: EC: Look up EC in DSDT
    [ 0.214102] ACPI: Executed 1 blocks of module-level executable AML code
    [ 0.217442] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
    [ 0.218088] ACPI: SSDT 7ba6fc98 001E1 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
    [ 0.218783] ACPI: Dynamic OEM Table Load:
    [ 0.218788] ACPI: SSDT (null) 001E1 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
    [ 0.219036] ACPI: SSDT 7ba6d598 00537 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
    [ 0.219702] ACPI: Dynamic OEM Table Load:
    [ 0.219706] ACPI: SSDT (null) 00537 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
    [ 0.237115] ACPI: SSDT 7ba6ee18 001CF (v01 PmRef ApIst 00003000 INTL 20051117)
    [ 0.237838] ACPI: Dynamic OEM Table Load:
    [ 0.237843] ACPI: SSDT (null) 001CF (v01 PmRef ApIst 00003000 INTL 20051117)
    [ 0.246829] ACPI: SSDT 7ba6ff18 0008D (v01 PmRef ApCst 00003000 INTL 20051117)
    [ 0.247515] ACPI: Dynamic OEM Table Load:
    [ 0.247520] ACPI: SSDT (null) 0008D (v01 PmRef ApCst 00003000 INTL 20051117)
    [ 0.257074] ACPI: Interpreter enabled
    [ 0.257081] ACPI: (supports S0 S3 S4 S5)
    [ 0.257124] ACPI: Using IOAPIC for interrupt routing
    [ 0.265711] ACPI: EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62
    [ 0.265982] ACPI: No dock devices found.
    [ 0.265985] HEST: Table not found.
    [ 0.265991] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.266509] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.267544] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
    [ 0.267549] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
    [ 0.267553] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
    [ 0.267560] pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xfebfffff]
    [ 0.267579] pci 0000:00:00.0: [8086:2a40] type 0 class 0x000600
    [ 0.267613] DMAR: Forcing write-buffer flush capability
    [ 0.267616] DMAR: Disabling IOMMU for graphics on this chipset
    [ 0.267647] pci 0000:00:02.0: [8086:2a42] type 0 class 0x000300
    [ 0.267668] pci 0000:00:02.0: reg 10: [mem 0x90000000-0x903fffff 64bit]
    [ 0.267681] pci 0000:00:02.0: reg 18: [mem 0x80000000-0x8fffffff 64bit pref]
    [ 0.267691] pci 0000:00:02.0: reg 20: [io 0x30d0-0x30d7]
    [ 0.267738] pci 0000:00:02.1: [8086:2a43] type 0 class 0x000380
    [ 0.267756] pci 0000:00:02.1: reg 10: [mem 0x92400000-0x924fffff 64bit]
    [ 0.267863] pci 0000:00:1a.0: [8086:2937] type 0 class 0x000c03
    [ 0.267945] pci 0000:00:1a.0: reg 20: [io 0x30a0-0x30bf]
    [ 0.268041] pci 0000:00:1a.7: [8086:293c] type 0 class 0x000c03
    [ 0.272125] pci 0000:00:1a.7: reg 10: [mem 0x94504c00-0x94504fff]
    [ 0.296690] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
    [ 0.296698] pci 0000:00:1a.7: PME# disabled
    [ 0.296734] pci 0000:00:1b.0: [8086:293e] type 0 class 0x000403
    [ 0.296759] pci 0000:00:1b.0: reg 10: [mem 0x94500000-0x94503fff 64bit]
    [ 0.296845] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.296852] pci 0000:00:1b.0: PME# disabled
    [ 0.296883] pci 0000:00:1c.0: [8086:2940] type 1 class 0x000604
    [ 0.296968] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.296974] pci 0000:00:1c.0: PME# disabled
    [ 0.297011] pci 0000:00:1c.3: [8086:2946] type 1 class 0x000604
    [ 0.297098] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
    [ 0.297105] pci 0000:00:1c.3: PME# disabled
    [ 0.297148] pci 0000:00:1d.0: [8086:2934] type 0 class 0x000c03
    [ 0.297230] pci 0000:00:1d.0: reg 20: [io 0x3080-0x309f]
    [ 0.297313] pci 0000:00:1d.1: [8086:2935] type 0 class 0x000c03
    [ 0.297391] pci 0000:00:1d.1: reg 20: [io 0x3060-0x307f]
    [ 0.297471] pci 0000:00:1d.2: [8086:2936] type 0 class 0x000c03
    [ 0.297552] pci 0000:00:1d.2: reg 20: [io 0x3040-0x305f]
    [ 0.297646] pci 0000:00:1d.7: [8086:293a] type 0 class 0x000c03
    [ 0.302125] pci 0000:00:1d.7: reg 10: [mem 0x94504800-0x94504bff]
    [ 0.328820] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    [ 0.328828] pci 0000:00:1d.7: PME# disabled
    [ 0.328858] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
    [ 0.328949] pci 0000:00:1f.0: [8086:2917] type 0 class 0x000601
    [ 0.329112] pci 0000:00:1f.2: [8086:2929] type 0 class 0x000106
    [ 0.329145] pci 0000:00:1f.2: reg 10: [io 0x30c8-0x30cf]
    [ 0.329159] pci 0000:00:1f.2: reg 14: [io 0x30dc-0x30df]
    [ 0.329172] pci 0000:00:1f.2: reg 18: [io 0x30c0-0x30c7]
    [ 0.329185] pci 0000:00:1f.2: reg 1c: [io 0x30d8-0x30db]
    [ 0.329199] pci 0000:00:1f.2: reg 20: [io 0x3020-0x303f]
    [ 0.329212] pci 0000:00:1f.2: reg 24: [mem 0x94504000-0x945047ff]
    [ 0.329268] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.329274] pci 0000:00:1f.2: PME# disabled
    [ 0.329302] pci 0000:00:1f.3: [8086:2930] type 0 class 0x000c05
    [ 0.329328] pci 0000:00:1f.3: reg 10: [mem 0x94505000-0x945050ff 64bit]
    [ 0.329362] pci 0000:00:1f.3: reg 20: [io 0x3000-0x301f]
    [ 0.329486] pci 0000:01:00.0: [1969:1063] type 0 class 0x000200
    [ 0.329519] pci 0000:01:00.0: reg 10: [mem 0x93500000-0x9353ffff 64bit]
    [ 0.329537] pci 0000:01:00.0: reg 18: [io 0x2000-0x207f]
    [ 0.329645] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.329653] pci 0000:01:00.0: PME# disabled
    [ 0.333336] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
    [ 0.333343] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
    [ 0.333349] pci 0000:00:1c.0: bridge window [mem 0x93500000-0x944fffff]
    [ 0.333360] pci 0000:00:1c.0: bridge window [mem 0x90400000-0x913fffff 64bit pref]
    [ 0.333454] pci 0000:02:00.0: [8086:0083] type 0 class 0x000280
    [ 0.333498] pci 0000:02:00.0: reg 10: [mem 0x92500000-0x92501fff 64bit]
    [ 0.333662] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
    [ 0.333671] pci 0000:02:00.0: PME# disabled
    [ 0.340004] pci 0000:00:1c.3: PCI bridge to [bus 02-02]
    [ 0.340011] pci 0000:00:1c.3: bridge window [io 0x1000-0x1fff]
    [ 0.340018] pci 0000:00:1c.3: bridge window [mem 0x92500000-0x934fffff]
    [ 0.340028] pci 0000:00:1c.3: bridge window [mem 0x91400000-0x923fffff 64bit pref]
    [ 0.340121] pci 0000:00:1e.0: PCI bridge to [bus 03-03] (subtractive decode)
    [ 0.340128] pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
    [ 0.340135] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
    [ 0.340145] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    [ 0.340150] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
    [ 0.340154] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
    [ 0.340158] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
    [ 0.340163] pci 0000:00:1e.0: bridge window [mem 0x80000000-0xfebfffff] (subtractive decode)
    [ 0.340186] pci_bus 0000:00: on NUMA node 0
    [ 0.340192] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    [ 0.340631] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
    [ 0.340734] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT]
    [ 0.340832] pci0000:00: Requesting ACPI _OSC control (0x1d)
    [ 0.340835] Unable to assume _OSC PCIe control. Disabling ASPM
    [ 0.348405] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
    [ 0.348504] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
    [ 0.348599] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
    [ 0.348693] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12)
    [ 0.348788] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
    [ 0.348886] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
    [ 0.348981] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 *11 12)
    [ 0.349075] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
    [ 0.349214] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.349232] vgaarb: loaded
    [ 0.349386] PCI: Using ACPI for IRQ routing
    [ 0.349389] PCI: pci_cache_line_size set to 64 bytes
    [ 0.349500] reserve RAM buffer: 000000000009e000 - 000000000009ffff
    [ 0.349504] reserve RAM buffer: 000000007ba60000 - 000000007bffffff
    [ 0.349510] reserve RAM buffer: 000000007bb80000 - 000000007bffffff
    [ 0.349514] reserve RAM buffer: 000000007bbe2000 - 000000007bffffff
    [ 0.349518] reserve RAM buffer: 000000007bc00000 - 000000007bffffff
    [ 0.349695] NetLabel: Initializing
    [ 0.349698] NetLabel: domain hash size = 128
    [ 0.349700] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.349720] NetLabel: unlabeled traffic allowed by default
    [ 0.349740] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
    [ 0.349748] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
    [ 0.349756] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
    [ 0.359999] Switching to clocksource hpet
    [ 0.363178] Switched to NOHz mode on CPU #0
    [ 0.363276] Switched to NOHz mode on CPU #1
    [ 0.370116] pnp: PnP ACPI init
    [ 0.370143] ACPI: bus type pnp registered
    [ 0.370722] pnp 00:00: [bus 00-ff]
    [ 0.370727] pnp 00:00: [io 0x0000-0x0cf7 window]
    [ 0.370731] pnp 00:00: [io 0x0cf8-0x0cff]
    [ 0.370735] pnp 00:00: [io 0x0d00-0xffff window]
    [ 0.370739] pnp 00:00: [mem 0x000a0000-0x000bffff window]
    [ 0.370743] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
    [ 0.370747] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
    [ 0.370751] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
    [ 0.370755] pnp 00:00: [mem 0x000cc000-0x000cffff window]
    [ 0.370759] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
    [ 0.370763] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
    [ 0.370767] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
    [ 0.370770] pnp 00:00: [mem 0x000dc000-0x000dffff window]
    [ 0.370774] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
    [ 0.370778] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
    [ 0.370782] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
    [ 0.370786] pnp 00:00: [mem 0x000ec000-0x000effff window]
    [ 0.370790] pnp 00:00: [mem 0x000f0000-0x000fffff window]
    [ 0.370794] pnp 00:00: [mem 0x80000000-0xfebfffff window]
    [ 0.370798] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
    [ 0.370911] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
    [ 0.371140] pnp 00:01: [io 0x002e-0x002f]
    [ 0.371144] pnp 00:01: [io 0x004e-0x004f]
    [ 0.371148] pnp 00:01: [io 0x164e-0x164f]
    [ 0.371151] pnp 00:01: [io 0x0061]
    [ 0.371154] pnp 00:01: [io 0x0070]
    [ 0.371157] pnp 00:01: [io 0x0080]
    [ 0.371160] pnp 00:01: [io 0x0092]
    [ 0.371163] pnp 00:01: [io 0x00b2-0x00b3]
    [ 0.371167] pnp 00:01: [io 0x0063]
    [ 0.371170] pnp 00:01: [io 0x0065]
    [ 0.371173] pnp 00:01: [io 0x0067]
    [ 0.371176] pnp 00:01: [io 0x0600-0x060f]
    [ 0.371180] pnp 00:01: [io 0x0610]
    [ 0.371183] pnp 00:01: [io 0x0800-0x080f]
    [ 0.371186] pnp 00:01: [io 0x0810-0x0817]
    [ 0.371190] pnp 00:01: [io 0x0820-0x0823]
    [ 0.371193] pnp 00:01: [io 0x0400-0x047f]
    [ 0.371196] pnp 00:01: [io 0x0500-0x053f]
    [ 0.371200] pnp 00:01: [mem 0xf8000000-0xfbffffff]
    [ 0.371203] pnp 00:01: [mem 0xfed1c000-0xfed1ffff]
    [ 0.371211] pnp 00:01: [mem 0xfed10000-0xfed13fff]
    [ 0.371215] pnp 00:01: [mem 0xfed18000-0xfed18fff]
    [ 0.371218] pnp 00:01: [mem 0xfed19000-0xfed19fff]
    [ 0.371222] pnp 00:01: [mem 0xfec00000-0xfec00fff]
    [ 0.371225] pnp 00:01: [mem 0xfed20000-0xfed3ffff]
    [ 0.371229] pnp 00:01: [mem 0xfed40000-0xfed44fff]
    [ 0.371232] pnp 00:01: [mem 0xfed45000-0xfed8ffff]
    [ 0.371236] pnp 00:01: [mem 0xfee00000-0xfee00fff]
    [ 0.371273] pnp 00:01: disabling [io 0x164e-0x164f] because it overlaps 0000:00:1c.3 BAR 13 [io 0x1000-0x1fff]
    [ 0.371372] system 00:01: [io 0x0600-0x060f] has been reserved
    [ 0.371377] system 00:01: [io 0x0610] has been reserved
    [ 0.371381] system 00:01: [io 0x0800-0x080f] has been reserved
    [ 0.371386] system 00:01: [io 0x0810-0x0817] has been reserved
    [ 0.371390] system 00:01: [io 0x0820-0x0823] has been reserved
    [ 0.371394] system 00:01: [io 0x0400-0x047f] has been reserved
    [ 0.371399] system 00:01: [io 0x0500-0x053f] has been reserved
    [ 0.371405] system 00:01: [mem 0xf8000000-0xfbffffff] has been reserved
    [ 0.371410] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 0.371414] system 00:01: [mem 0xfed10000-0xfed13fff] has been reserved
    [ 0.371419] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
    [ 0.371424] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
    [ 0.371429] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
    [ 0.371434] system 00:01: [mem 0xfed20000-0xfed3ffff] has been reserved
    [ 0.371438] system 00:01: [mem 0xfed40000-0xfed44fff] has been reserved
    [ 0.371443] system 00:01: [mem 0xfed45000-0xfed8ffff] has been reserved
    [ 0.371448] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
    [ 0.371453] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.371471] pnp 00:02: [io 0x0000-0x001f]
    [ 0.371474] pnp 00:02: [io 0x0081-0x0091]
    [ 0.371478] pnp 00:02: [io 0x0093-0x009f]
    [ 0.371481] pnp 00:02: [io 0x00c0-0x00df]
    [ 0.371485] pnp 00:02: [dma 4]
    [ 0.371537] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.371576] pnp 00:03: [io 0x0070-0x0077]
    [ 0.371630] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.371735] pnp 00:04: [irq 0 disabled]
    [ 0.371750] pnp 00:04: [irq 8]
    [ 0.371753] pnp 00:04: [mem 0xfed00000-0xfed003ff]
    [ 0.371809] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
    [ 0.371828] pnp 00:05: [io 0x00f0]
    [ 0.371835] pnp 00:05: [irq 13]
    [ 0.371889] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.371907] pnp 00:06: [mem 0xff800000-0xffffffff]
    [ 0.371965] pnp 00:06: Plug and Play ACPI device, IDs INT0800 (active)
    [ 0.371991] pnp 00:07: [io 0x0060]
    [ 0.371995] pnp 00:07: [io 0x0064]
    [ 0.372003] pnp 00:07: [irq 1]
    [ 0.372061] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)
    [ 0.372090] pnp 00:08: [irq 12]
    [ 0.372150] pnp 00:08: Plug and Play ACPI device, IDs SYN1b20 PNP0f13 (active)
    [ 0.372300] pnp: PnP ACPI: found 9 devices
    [ 0.372303] ACPI: ACPI bus type pnp unregistered
    [ 0.409749] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
    [ 0.409755] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
    [ 0.409764] pci 0000:00:1c.0: bridge window [mem 0x93500000-0x944fffff]
    [ 0.409772] pci 0000:00:1c.0: bridge window [mem 0x90400000-0x913fffff 64bit pref]
    [ 0.409782] pci 0000:00:1c.3: PCI bridge to [bus 02-02]
    [ 0.409787] pci 0000:00:1c.3: bridge window [io 0x1000-0x1fff]
    [ 0.409795] pci 0000:00:1c.3: bridge window [mem 0x92500000-0x934fffff]
    [ 0.409802] pci 0000:00:1c.3: bridge window [mem 0x91400000-0x923fffff 64bit pref]
    [ 0.409812] pci 0000:00:1e.0: PCI bridge to [bus 03-03]
    [ 0.409815] pci 0000:00:1e.0: bridge window [io disabled]
    [ 0.409823] pci 0000:00:1e.0: bridge window [mem disabled]
    [ 0.409829] pci 0000:00:1e.0: bridge window [mem pref disabled]
    [ 0.409853] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    [ 0.409861] pci 0000:00:1c.0: setting latency timer to 64
    [ 0.409875] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
    [ 0.409881] pci 0000:00:1c.3: setting latency timer to 64
    [ 0.409891] pci 0000:00:1e.0: setting latency timer to 64
    [ 0.409897] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 0.409901] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 0.409905] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.409909] pci_bus 0000:00: resource 7 [mem 0x80000000-0xfebfffff]
    [ 0.409914] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
    [ 0.409918] pci_bus 0000:01: resource 1 [mem 0x93500000-0x944fffff]
    [ 0.409922] pci_bus 0000:01: resource 2 [mem 0x90400000-0x913fffff 64bit pref]
    [ 0.409927] pci_bus 0000:02: resource 0 [io 0x1000-0x1fff]
    [ 0.409931] pci_bus 0000:02: resource 1 [mem 0x92500000-0x934fffff]
    [ 0.409935] pci_bus 0000:02: resource 2 [mem 0x91400000-0x923fffff 64bit pref]
    [ 0.409940] pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7]
    [ 0.409943] pci_bus 0000:03: resource 5 [io 0x0d00-0xffff]
    [ 0.409947] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.409952] pci_bus 0000:03: resource 7 [mem 0x80000000-0xfebfffff]
    [ 0.410023] NET: Registered protocol family 2
    [ 0.410132] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    [ 0.410465] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
    [ 0.411087] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
    [ 0.411362] TCP: Hash tables configured (established 131072 bind 65536)
    [ 0.411366] TCP reno registered
    [ 0.411370] UDP hash table entries: 512 (order: 2, 16384 bytes)
    [ 0.411381] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    [ 0.411559] NET: Registered protocol family 1
    [ 0.411580] pci 0000:00:02.0: Boot video device
    [ 0.440052] PCI: CLS 64 bytes, default 64
    [ 0.440120] Unpacking initramfs...
    [ 0.493687] Freeing initrd memory: 1728k freed
    [ 0.494435] Simple Boot Flag value 0x5 read from CMOS RAM was invalid
    [ 0.494439] Simple Boot Flag at 0x44 set to 0x1
    [ 0.494754] apm: BIOS not found.
    [ 0.494943] audit: initializing netlink socket (disabled)
    [ 0.494958] type=2000 audit(1312551622.493:1): initialized
    [ 0.495391] highmem bounce pool size: 64 pages
    [ 0.495398] HugeTLB registered 4 MB page size, pre-allocated 0 pages
    [ 0.498715] VFS: Disk quotas dquot_6.5.2
    [ 0.498846] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [ 0.499018] msgmni has been set to 1714
    [ 0.499314] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
    [ 0.499357] io scheduler noop registered
    [ 0.499361] io scheduler deadline registered
    [ 0.499380] io scheduler cfq registered (default)
    [ 0.499553] pcieport 0000:00:1c.0: setting latency timer to 64
    [ 0.499624] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
    [ 0.499729] pcieport 0000:00:1c.3: setting latency timer to 64
    [ 0.499792] pcieport 0000:00:1c.3: irq 41 for MSI/MSI-X
    [ 0.500070] intel_idle: MWAIT substates: 0x22220
    [ 0.500074] intel_idle: does not run on family 6 model 23
    [ 0.500082] ERST: Table is not found!
    [ 0.500103] isapnp: Scanning for PnP cards...
    [ 0.857044] isapnp: No Plug & Play device found
    [ 0.857122] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 1.060716] i8042: PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOUE] at 0x60,0x64 irq 1,12
    [ 1.068400] i8042: Detected active multiplexing controller, rev 1.1
    [ 1.071789] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 1.071804] serio: i8042 AUX0 port at 0x60,0x64 irq 12
    [ 1.071809] serio: i8042 AUX1 port at 0x60,0x64 irq 12
    [ 1.071813] serio: i8042 AUX2 port at 0x60,0x64 irq 12
    [ 1.071818] serio: i8042 AUX3 port at 0x60,0x64 irq 12
    [ 1.072099] mousedev: PS/2 mouse device common for all mice
    [ 1.072185] rtc_cmos 00:03: RTC can wake from S4
    [ 1.086817] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
    [ 1.086852] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
    [ 1.086887] cpuidle: using governor ladder
    [ 1.086890] cpuidle: using governor menu
    [ 1.087261] TCP cubic registered
    [ 1.087265] NET: Registered protocol family 17
    [ 1.087276] Registering the dns_resolver key type
    [ 1.087307] Using IPI No-Shortcut mode
    [ 1.087437] PM: Hibernation image not present or could not be loaded.
    [ 1.087445] registered taskstats version 1
    [ 1.087957] rtc_cmos 00:03: setting system clock to 2011-08-05 13:40:23 UTC (1312551623)
    [ 1.088039] Initializing network drop monitor service
    [ 1.088128] Freeing unused kernel memory: 512k freed
    [ 1.088469] Write protecting the kernel text: 3380k
    [ 1.088507] Write protecting the kernel read-only data: 1028k
    [ 1.093885] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    [ 1.106227] udevd[54]: starting version 171
    [ 1.236052] SCSI subsystem initialized
    [ 1.269724] libata version 3.00 loaded.
    [ 1.282619] ahci 0000:00:1f.2: version 3.0
    [ 1.282637] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
    [ 1.282703] ahci 0000:00:1f.2: irq 42 for MSI/MSI-X
    [ 1.282767] ahci: SSS flag set, parallel bus scan disabled
    [ 1.282814] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
    [ 1.282820] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led pmp pio slum part ccc ems
    [ 1.282828] ahci 0000:00:1f.2: setting latency timer to 64
    [ 1.301035] scsi0 : ahci
    [ 1.301194] scsi1 : ahci
    [ 1.301318] scsi2 : ahci
    [ 1.301438] scsi3 : ahci
    [ 1.301557] scsi4 : ahci
    [ 1.301679] scsi5 : ahci
    [ 1.301772] ata1: SATA max UDMA/133 abar m2048@0x94504000 port 0x94504100 irq 42
    [ 1.301778] ata2: SATA max UDMA/133 abar m2048@0x94504000 port 0x94504180 irq 42
    [ 1.301782] ata3: DUMMY
    [ 1.301784] ata4: DUMMY
    [ 1.301788] ata5: SATA max UDMA/133 abar m2048@0x94504000 port 0x94504300 irq 42
    [ 1.301793] ata6: SATA max UDMA/133 abar m2048@0x94504000 port 0x94504380 irq 42
    [ 1.496710] Refined TSC clocksource calibration: 1296.749 MHz.
    [ 1.496717] Switching to clocksource tsc
    [ 1.786699] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 1.787736] ata1.00: ATA-8: Hitachi HTS543225L9A300, FBEOC40C, max UDMA/133
    [ 1.787741] ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
    [ 1.788946] ata1.00: configured for UDMA/133
    [ 1.789123] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54322 FBEO PQ: 0 ANSI: 5
    [ 2.106690] ata2: SATA link down (SStatus 0 SControl 300)
    [ 2.426689] ata5: SATA link down (SStatus 0 SControl 300)
    [ 2.746690] ata6: SATA link down (SStatus 0 SControl 300)
    [ 2.760584] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
    [ 2.760671] sd 0:0:0:0: [sda] Write Protect is off
    [ 2.760676] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 2.760709] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.798506] sda: sda1 sda2 sda3 sda4
    [ 2.799028] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 3.310879] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
    [ 4.653828] udevd[228]: starting version 173
    [ 4.958869] ACPI: acpi_idle registered with cpuidle
    [ 4.959125] Monitor-Mwait will be used to enter C-1 state
    [ 4.959159] Monitor-Mwait will be used to enter C-2 state
    [ 4.959167] Marking TSC unstable due to TSC halts in idle
    [ 4.959208] Switching to clocksource hpet
    [ 5.052561] fuse init (API version 7.16)
    [ 5.094399] acerhdf: Acer Aspire One Fan driver, v.0.5.24
    [ 5.094431] acerhdf: unknown (unsupported) BIOS version Acer/Aspire 1810TZ/v1.3314, please report, aborting!
    [ 5.377790] Linux agpgart interface v0.103
    [ 5.381930] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
    [ 5.382452] ACPI: AC Adapter [ACAD] (off-line)
    [ 5.389644] wmi: Mapper loaded
    [ 5.390172] iTCO_vendor_support: vendor-support=0
    [ 5.532413] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
    [ 5.532424] ACPI: Power Button [PWRB]
    [ 5.532507] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
    [ 5.548014] acer_wmi: Acer Laptop ACPI-WMI Extras
    [ 5.550648] acer_wmi: Brightness must be controlled by generic video driver
    [ 5.554953] ACPI: Lid Switch [LID0]
    [ 5.555062] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
    [ 5.555072] ACPI: Sleep Button [SLPB]
    [ 5.555166] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
    [ 5.555173] ACPI: Power Button [PWRF]
    [ 5.560994] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    [ 5.569140] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
    [ 5.569153] ACPI: Battery Slot [BAT1] (battery present)
    [ 5.570951] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
    [ 5.573564] iTCO_wdt: Found a ICH9M-E TCO device (Version=2, TCOBASE=0x0460)
    [ 5.573653] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 5.602755] usbcore: registered new interface driver usbfs
    [ 5.602793] usbcore: registered new interface driver hub
    [ 5.606733] usbcore: registered new device driver usb
    [ 5.623405] input: PC Speaker as /devices/platform/pcspkr/input/input5
    [ 5.659329] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 5.659373] ehci_hcd 0000:00:1a.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
    [ 5.659401] ehci_hcd 0000:00:1a.7: setting latency timer to 64
    [ 5.659407] ehci_hcd 0000:00:1a.7: EHCI Host Controller
    [ 5.659455] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
    [ 5.670065] ehci_hcd 0000:00:1a.7: debug port 1
    [ 5.673944] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
    [ 5.673971] ehci_hcd 0000:00:1a.7: irq 19, io mem 0x94504c00
    [ 5.690924] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
    [ 5.691336] hub 1-0:1.0: USB hub found
    [ 5.691345] hub 1-0:1.0: 2 ports detected
    [ 5.691477] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
    [ 5.691508] ehci_hcd 0000:00:1d.7: setting latency timer to 64
    [ 5.691514] ehci_hcd 0000:00:1d.7: EHCI Host Controller
    [ 5.691528] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
    [ 5.702271] cfg80211: Calling CRDA to update world regulatory domain
    [ 5.706752] ehci_hcd 0000:00:1d.7: debug port 1
    [ 5.710655] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
    [ 5.710683] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x94504800
    [ 5.723379] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    [ 5.723603] hub 2-0:1.0: USB hub found
    [ 5.723610] hub 2-0:1.0: 6 ports detected
    [ 5.724256] agpgart-intel 0000:00:00.0: Intel GM45 Chipset
    [ 5.724463] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
    [ 5.725927] agpgart-intel 0000:00:00.0: detected 65536K stolen memory
    [ 5.726502] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000
    [ 5.802604] uhci_hcd: USB Universal Host Controller Interface driver
    [ 5.802687] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 5.802702] uhci_hcd 0000:00:1a.0: setting latency timer to 64
    [ 5.802709] uhci_hcd 0000:00:1a.0: UHCI Host Controller
    [ 5.802732] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
    [ 5.813675] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000030a0
    [ 5.814571] hub 3-0:1.0: USB hub found
    [ 5.814580] hub 3-0:1.0: 2 ports detected
    [ 5.814712] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
    [ 5.814725] uhci_hcd 0000:00:1d.0: setting latency timer to 64
    [ 5.814730] uhci_hcd 0000:00:1d.0: UHCI Host Controller
    [ 5.814748] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
    [ 5.823482] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00003080
    [ 5.824221] hub 4-0:1.0: USB hub found
    [ 5.824230] hub 4-0:1.0: 2 ports detected
    [ 5.824360] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
    [ 5.824373] uhci_hcd 0000:00:1d.1: setting latency timer to 64
    [ 5.824378] uhci_hcd 0000:00:1d.1: UHCI Host Controller
    [ 5.824392] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
    [ 5.836745] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003060
    [ 5.836988] hub 5-0:1.0: USB hub found
    [ 5.836995] hub 5-0:1.0: 2 ports detected
    [ 5.837118] uhci_hcd 0000:00:1d.2: PCI INT D -> GSI 16 (level, low) -> IRQ 16
    [ 5.837130] uhci_hcd 0000:00:1d.2: setting latency timer to 64
    [ 5.837135] uhci_hcd 0000:00:1d.2: UHCI Host Controller
    [ 5.837148] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
    [ 5.846757] uhci_hcd 0000:00:1d.2: irq 16, io base 0x00003040
    [ 5.846997] hub 6-0:1.0: USB hub found
    [ 5.847004] hub 6-0:1.0: 2 ports detected
    [ 5.869833] sd 0:0:0:0: Attached scsi generic sg0 type 0
    [ 5.909784] [drm] Initialized drm 1.1.0 20060810
    [ 5.926221] atl1c 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 5.926238] atl1c 0000:01:00.0: setting latency timer to 64
    [ 6.014499] atl1c 0000:01:00.0: version 1.0.1.0-NAPI
    [ 6.022590] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 6.022599] i915 0000:00:02.0: setting latency timer to 64
    [ 6.033370] usb 2-5: new high speed USB device number 2 using ehci_hcd
    [ 6.045183] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:
    [ 6.045188] iwlagn: Copyright(c) 2003-2010 Intel Corporation
    [ 6.045269] iwlagn 0000:02:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
    [ 6.045281] iwlagn 0000:02:00.0: setting latency timer to 64
    [ 6.045314] iwlagn 0000:02:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C
    [ 6.066230] iwlagn 0000:02:00.0: device EEPROM VER=0x15d, CALIB=0x6
    [ 6.066236] iwlagn 0000:02:00.0: Device SKU: 0X9
    [ 6.066240] iwlagn 0000:02:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3
    [ 6.066261] iwlagn 0000:02:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels
    [ 6.066513] iwlagn 0000:02:00.0: irq 43 for MSI/MSI-X
    [ 6.071614] i915 0000:00:02.0: irq 44 for MSI/MSI-X
    [ 6.071623] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
    [ 6.071626] [drm] Driver supports precise vblank timestamp query.
    [ 6.167372] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
    [ 6.236519] iwlagn 0000:02:00.0: loaded firmware version 39.31.5.1 build 35138
    [ 6.236889] Registered led device: phy0-led
    [ 6.309104] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
    [ 6.435863] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000
    [ 6.480908] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input6
    [ 6.507822] Linux media interface: v0.10
    [ 6.580021] Linux video capture interface: v2.00
    [ 6.591629] uvcvideo: Found UVC 1.00 device WebCam (064e:a102)
    [ 6.608274] input: WebCam as /devices/pci0000:00/0000:00:1d.7/usb2/2-5/2-5:1.0/input/input7
    [ 6.608368] usbcore: registered new interface driver uvcvideo
    [ 6.608371] USB Video Class driver (v1.0.0)
    [ 6.624890] fbcon: inteldrmfb (fb0) is primary device
    [ 6.671041] Console: switching to colour frame buffer device 170x48
    [ 6.678170] fb0: inteldrmfb frame buffer device
    [ 6.678173] drm: registered panic notifier
    [ 6.679734] acpi device:03: registered as cooling_device2
    [ 6.679988] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input8
    [ 6.680104] ACPI: Video Device [OVGA] (multi-head: yes rom: no post: no)
    [ 6.680793] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
    [ 6.680840] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
    [ 6.680937] HDA Intel 0000:00:1b.0: irq 45 for MSI/MSI-X
    [ 6.680975] HDA Intel 0000:00:1b.0: setting latency timer to 64
    [ 6.802470] hda_codec: ALC269: BIOS auto-probing.
    [ 6.803832] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
    [ 6.833736] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
    [ 6.833855] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
    [ 8.406870] EXT4-fs (sda3): re-mounted. Opts: (null)
    [ 8.676079] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
    [ 8.886041] Adding 265068k swap on /dev/sda2. Priority:-1 extents:1 across:265068k
    [ 12.277210] atl1c 0000:01:00.0: irq 46 for MSI/MSI-X
    [ 12.600410] /dev/vmmon[897]: Module vmmon: registered with major=10 minor=165
    [ 12.600421] /dev/vmmon[897]: Module vmmon: initialized
    [ 12.646908] /dev/vmci[905]: VMCI: Driver initialized.
    [ 12.647204] /dev/vmci[905]: Module vmci: registered with major=10 minor=58
    [ 12.647209] /dev/vmci[905]: Module vmci: initialized
    [ 12.827251] ppdev: user-space parallel port driver
    [ 13.786476] /dev/vmnet: open called by PID 979 (vmnet-dhcpd)
    [ 13.786488] /dev/vmnet: hub 1 does not exist, allocating memory.
    [ 13.786521] /dev/vmnet: port on hub 1 successfully opened
    [ 13.801438] /dev/vmnet: open called by PID 981 (vmnet-netifup)
    [ 13.801452] /dev/vmnet: port on hub 1 successfully opened
    [ 13.854670] /dev/vmnet: open called by PID 983 (vmnet-dhcpd)
    [ 13.854683] /dev/vmnet: hub 8 does not exist, allocating memory.
    [ 13.854720] /dev/vmnet: port on hub 8 successfully opened
    [ 13.915864] /dev/vmnet: open called by PID 987 (vmnet-natd)
    [ 13.915881] /dev/vmnet: port on hub 8 successfully opened
    [ 13.936302] /dev/vmnet: open called by PID 988 (vmnet-netifup)
    [ 13.936317] /dev/vmnet: port on hub 8 successfully opened
    [ 38.702663] NET: Registered protocol family 10
    [ 38.704338] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 38.704788] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 39.752832] EXT4-fs (sda3): re-mounted. Opts: commit=600
    [ 40.413933] EXT4-fs (sda4): re-mounted. Opts: commit=600
    [ 48.976756] vmnet8: no IPv6 routers present
    [ 49.523376] vmnet1: no IPv6 routers present
    [ 105.125369] wlan0: authenticate with 00:15:e9:27:b5:38 (try 1)
    [ 105.127031] wlan0: authenticated
    [ 105.137382] wlan0: associate with 00:15:e9:27:b5:38 (try 1)
    [ 105.140390] wlan0: RX AssocResp from 00:15:e9:27:b5:38 (capab=0x471 status=0 aid=1)
    [ 105.140396] wlan0: associated
    [ 105.144018] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    [ 105.447100] /dev/vmnet: open called by PID 971 (vmnet-bridge)
    [ 105.447115] /dev/vmnet: hub 0 does not exist, allocating memory.
    [ 105.447150] /dev/vmnet: port on hub 0 successfully opened
    [ 105.447175] bridge-wlan0: device is wireless, enabling SMAC
    [ 105.447181] bridge-wlan0: up
    [ 105.448675] bridge-wlan0: attached
    [ 107.324643] wlan0: deauthenticating from 00:15:e9:27:b5:38 by local choice (reason=3)
    [ 107.400201] cfg80211: Calling CRDA to update world regulatory domain
    [ 107.423712] bridge-wlan0: disabling the bridge
    [ 107.440034] bridge-wlan0: down
    [ 107.440043] bridge-wlan0: detached
    [ 107.440111] /dev/vmnet: open called by PID 971 (vmnet-bridge)
    [ 107.440124] /dev/vmnet: hub 0 does not exist, allocating memory.
    [ 107.440157] /dev/vmnet: port on hub 0 successfully opened
    [ 107.440172] bridge-wlan0: device is wireless, enabling SMAC
    [ 107.440177] bridge-wlan0: up
    [ 107.440182] bridge-wlan0: attached
    [ 107.860411] bridge-wlan0: disabling the bridge
    [ 107.869871] wlan0: authenticate with 00:15:e9:27:b5:38 (try 1)
    [ 107.872071] wlan0: authenticated
    [ 107.872466] wlan0: associate with 00:15:e9:27:b5:38 (try 1)
    [ 107.875411] wlan0: RX ReassocResp from 00:15:e9:27:b5:38 (capab=0x471 status=0 aid=1)
    [ 107.875417] wlan0: associated
    [ 107.876696] bridge-wlan0: down
    [ 107.876705] bridge-wlan0: detached
    [ 107.904358] /dev/vmnet: open called by PID 971 (vmnet-bridge)
    [ 107.904374] /dev/vmnet: hub 0 does not exist, allocating memory.
    [ 107.904409] /dev/vmnet: port on hub 0 successfully opened
    [ 107.904423] bridge-wlan0: device is wireless, enabling SMAC
    [ 107.904428] bridge-wlan0: up
    [ 107.905917] bridge-wlan0: attached
    [ 118.910106] wlan0: no IPv6 routers present
    This is the output of /var/log/boot
    Fri Aug 5 15:40:30 2011: :: Adjusting system time and setting kernel timezone ^[[71G [BUSY] ^[[71G [DONE]
    Fri Aug 5 15:40:30 2011: :: Starting UDev Daemon ^[[71G [BUSY] ^[[71G [DONE]
    Fri Aug 5 15:40:30 2011: :: Triggering UDev uevents ^[[71G [BUSY] ^[[71G [DONE]
    Fri Aug 5 15:40:30 2011: :: Loading Modules ^[[71G [BUSY] ^[[71G [FAIL]
    Fri Aug 5 15:40:30 2011: :: Waiting for UDev uevents to be processed ^[[71G [BUSY] ^[[71G [DONE]
    Fri Aug 5 15:40:30 2011: :: Bringing up loopback interface ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:30 2011: :: Checking Filesystems ^[[161G [BUSY] /dev/sda3: clean, 190178/480496 files, 1530694/1921775 blocks
    Fri Aug 5 15:40:30 2011: /dev/sda4: clean, 49123/14761984 files, 38814365/59034858 blocks
    Fri Aug 5 15:40:30 2011: /dev/sda1: clean, 30/26104 files, 19115/104388 blocks
    Fri Aug 5 15:40:30 2011: ^[[161G [DONE]
    Fri Aug 5 15:40:30 2011: :: Remounting Root Read/Write ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:30 2011: :: Creating mtab ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:30 2011: :: Mounting Local Filesystems ^[[161G [BUSY] ^[[161G [FAIL]
    Fri Aug 5 15:40:31 2011: :: Activating Swap ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:31 2011: :: Configuring Time Zone ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:31 2011: :: Initializing Random Seed ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:31 2011: :: Removing Leftover Files ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:31 2011: :: Setting Hostname: gianluca-laptop ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:31 2011: :: Setting Locale: en_GB.UTF-8 ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:31 2011: :: Setting Consoles to UTF-8 mode ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:32 2011: :: Loading Keyboard Map: it ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:32 2011: :: Saving dmesg Log ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:32 2011: INIT: Entering runlevel: 5
    Fri Aug 5 15:40:32 2011: :: Starting Syslog-NG ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:32 2011: :: Starting D-BUS system messagebus ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:33 2011: :: Starting Avahi mDNS/DNS-SD Daemon ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:33 2011: :: Starting NetworkManager ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:33 2011: :: Mounting Network Filesystems ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:34 2011: :: Starting crond daemon ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:34 2011: :: Restoring ALSA Levels ^[[161G [BUSY] ^[[161G [DONE]
    Fri Aug 5 15:40:34 2011: Starting VMware services:
    Fri Aug 5 15:40:34 2011: VMware USB Arbitrator^[[71G done
    Fri Aug 5 15:40:34 2011: Virtual machine monitor^[[71G done
    Fri Aug 5 15:40:35 2011: Virtual machine communication interface^[[71G done
    Fri Aug 5 15:40:35 2011: VM communication interface socket family^[[71G done
    Fri Aug 5 15:40:35 2011: Blocking file system^[[71G done
    Fri Aug 5 15:40:35 2011: Virtual ethernet^[[71G done
    Fri Aug 5 15:40:36 2011: Shared Memory Available^[[71G done
    Fri Aug 5 15:40:36 2011: :: Starting Up Sensors ^[[161G [BUSY] ^[[161G [DONE]
    What could be the problem?
    Thanks

    Wed Aug 10 08:49:11 2011: :: Adjusting system time and setting kernel timezone ^[[119G [BUSY] ^[[119G [DONE]
    Wed Aug 10 08:49:11 2011: :: Starting UDev Daemon ^[[119G [BUSY] ^[[119G [DONE]
    Wed Aug 10 08:49:11 2011: :: Triggering UDev uevents ^[[119G [BUSY] ^[[119G [DONE]
    Wed Aug 10 08:49:11 2011: :: Loading Modules ^[[119G [BUSY] ^[[119G [DONE]
    Wed Aug 10 08:49:11 2011: :: Waiting for UDev uevents to be processed ^[[119G [BUSY] ^[[119G [DONE]
    Wed Aug 10 08:49:11 2011: :: Bringing up loopback interface ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:11 2011: :: Checking Filesystems ^[[161G [BUSY] /dev/sda3: clean, 190755/480496 files, 1567027/1921775 blocks
    Wed Aug 10 08:49:11 2011: /dev/sda4: clean, 39914/14761984 files, 39001242/59034858 blocks
    Wed Aug 10 08:49:11 2011: /dev/sda1: clean, 29/26104 files, 19024/104388 blocks
    Wed Aug 10 08:49:11 2011: ^[[161G [DONE]
    Wed Aug 10 08:49:11 2011: :: Remounting Root Read/Write ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:11 2011: :: Creating mtab ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:11 2011: :: Mounting Local Filesystems ^[[161G [BUSY] ^[[161G [FAIL]
    Wed Aug 10 08:49:11 2011: :: Activating Swap ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:11 2011: :: Configuring Time Zone ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:11 2011: :: Initializing Random Seed ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:11 2011: :: Removing Leftover Files ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:12 2011: :: Setting Hostname: gianluca-laptop ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:12 2011: :: Setting Locale: en_GB.UTF-8 ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:12 2011: :: Setting Consoles to UTF-8 mode ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:12 2011: :: Loading Keyboard Map: it ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:12 2011: :: Saving dmesg Log ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:12 2011: INIT: Entering runlevel: 5
    Wed Aug 10 08:49:12 2011: :: Starting Syslog-NG ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:13 2011: :: Starting D-BUS system messagebus ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:13 2011: :: Starting Avahi mDNS/DNS-SD Daemon ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:14 2011: :: Starting NetworkManager ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:14 2011: :: Mounting Network Filesystems ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:14 2011: :: Starting crond daemon ^[[161G [BUSY] ^[[161G [DONE]
    Wed Aug 10 08:49:14 2011: :: Restoring ALSA Levels ^[[161G [BUSY] Found hardware: "HDA-Intel" "Intel Cantiga HDMI" "HDA:10ec0269,1025029b,00100004 HDA:80862802,80860101,001000
    Wed Aug 10 08:49:14 2011: Hardware is initialized using a generic method
    Wed Aug 10 08:49:14 2011: ^[[161G [FAIL]
    Wed Aug 10 08:49:15 2011: Starting VMware services:
    Wed Aug 10 08:49:15 2011: VMware USB Arbitrator^[[71G done
    Wed Aug 10 08:49:15 2011: Virtual machine monitor^[[71Gfailed
    Wed Aug 10 08:49:15 2011: Virtual machine communication interface^[[71Gfailed
    Wed Aug 10 08:49:15 2011: VM communication interface socket family^[[71Gfailed
    Wed Aug 10 08:49:15 2011: Blocking file system^[[71Gfailed
    Wed Aug 10 08:49:15 2011: Virtual ethernet^[[71Gfailed
    Wed Aug 10 08:49:15 2011: :: Starting Up Sensors ^[[161G [BUSY] ^[[161G [DONE]
    Ok, I still have that fail during the 'Mounting Local Filesystems'.
    If there isn't the swap partition it should be something else from my fstab..
    # /etc/fstab: static file system information
    # <file system> <dir> <type> <options> <dump> <pass>
    devpts /dev/pts devpts defaults 0 0
    shm /dev/shm tmpfs nodev,nosuid 0 0
    UUID=1b52b0c4-5b56-4bee-8966-65bcaffbf2ee /home ext4 defaults 0 1
    UUID=22475d68-29e5-4a22-8942-38cb30110d30 swap swap defaults 0 0
    UUID=2bef0cce-027d-44fa-a086-056c390cd847 / ext4 defaults 0 1
    UUID=59d811ed-2920-45c1-a5cc-e0675e212721 /boot ext2 defaults 0 1
    UUID=325220A852207331 /media/MyPassport ntfs defaults,nofail 0 2
    UUID=FDC0-6FEA /media/CowonIvana auto defaults,nofail 0 2
    UUID=7AEB-F44F /media/CentralEurope auto defaults,nofail 0 2
    UUID=287B-C290 /media/CowonGian auto defaults,nofail 0 2
    UUID=3F9D788B3774630C /media/SanDisk ntfs defaults,nofail 0 2
    But I can't find anything that looks unusual into my /etc/fstab

  • Start network connection during boot [KDE4]

    I want to able to connect to a network (with key) during boot.
    Right now, when my arch is booting, it is trying to connect to a dhcpcd during boot, but fails (after several seconds). Then knetworkmanager and even wicd doesn't seem to work correctly. Knetworkmanager (from KDEmod) seems like doesn't work at all.
    What can I do to make it connect during boot? (I usually connect only to one network).

    I got it working.. however, I am wondering if I have everything right in my rc.config file, in DAEMONS section (maybe I have there something extra, which I can turn off).
    #Static IP example
    #eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
    #eth0="dhcp"
    #INTERFACES=(eth0)
    # Routes to start at boot-up (in this order)
    # Declare each route then list in ROUTES
    # - prefix an entry in ROUTES with a ! to disable it
    gateway="default gw 192.168.0.1"
    ROUTES=(!gateway)
    # Enable these network profiles at boot-up. These are only useful
    # if you happen to need multiple network configurations (ie, laptop users)
    # - set to 'menu' to present a menu during boot-up (dialog package required)
    # - prefix an entry with a ! to disable it
    # Network profiles are found in /etc/network.d
    # This now requires the netcfg package
    NETWORKS=(wireless-wep)
    # DAEMONS
    # Daemons to start at boot-up (in this order)
    # - prefix a daemon with a ! to disable it
    # - prefix a daemon with a @ to start it up in the background
    DAEMONS=(syslog-ng network netfs net-profiles hal !networkmanager crond alsa kdm)
    Which one do I need? network, netfs? net-profiles?
    Last edited by kdar (2009-12-16 02:17:01)

  • Fail during boot up?

    Once in a while, my MacAir's screen does not come up right during booting up and had to restart.

    Try the following:
    Reinstalling Lion/Mountain Lion Without Erasing the Drive
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

  • [SOLVED] "Filesystem check failed" during boot process

    I was using XFCE on my netbook recently and clicked "shutdown".  It logged out to the command prompt and nothing happened.  Assuming that I'd clicked "logout" by mistake, I typed "pacman -Syu" to run an update...  And moments later it suddenly started the shutdown process.
    Now, whenever I boot up, I see the message below.  I tried booting from a GParted CD to check the filesystems for errors, but none were detected.
    Can anyone suggest what I might need to do to fix the problem?
    rootfs: clean, 11026/246512 files, 477083/984576 blocks
    home: clean, 4386/527280 files, 237183/2105344 blocks
    /dev/sdb2 is mounted. e2fsck: Cannot continue, aborting.
    ************* FILESYSTEM CHECK FAILED ************
    * Please repair manually and reboot. Note that the root
    * file system is currently mounted read-only. To remount
    * it read-write type: mount -n -o remount,rw /
    * when you exit the maintenance shell the system will
    * reboot automatically.
    Give root password for maintenance
    (or type Control-D to continue):
    Last edited by esuhl (2012-03-27 01:20:07)

    Thank you all for your replies :-)
    hadrons123 wrote:What happens when you do try the suggestion given by it?
    I don't exactly know how I should "repair manually"...  I thought a filesystem check in GParted would have been enough...
    lijpbasin wrote:You can boot the system using a archlinux live cd, and run fsck manually on every linux partition in the old system with options.
    DON'T mount any of the filesystems before running fsck, or your data will probably be lost. If you want to check the partition information first, run fdisk -l with root privileges.
    Thanks.  I tried booting from an ArchBang live CD last night and ran "e2fsck -pcv" on each partition.  The check completed, but the problem persists...  I just tried again using "fsck" as you suggested and got the following output (but the machine still fails to boot with the same error as before):
    fsck from util-linux 2.20.1
    e2fsck 1.41.14 (22-Dec-2010)
    usr was not cleanly unmounted, check forced.
    Pass 1: Checking inodes, blocks, and sizes
    Pass 2: Checking directory structure
    Pass 3: Checking directory connectivity
    Pass 4: Checking reference counts
    Pass 5: Checking group summary information
    usr: 115811/458752 files (1.7% non-contiguous), 783161/1834496 blocks
    Gcool wrote:
    /dev/sdb2 is mounted. e2fsck: Cannot continue, aborting.
    As mentioned already, the reason it's failing is because the /dev/sdb2 partition is mounted before it can be fsck'd. What is this partition exactly (which filesystem, what's on it, mountpoint,...)?
    I'm not overly familiar with the Linux boot process, but why would it suddenly be mounting this partition before fsck-ing it?  Even if it was mounted when the netbook shutdown, surely the boot process starts with all partitions unmounted...?  Anyway, the partition details from /etc/fstab are below.
    <file system> <dir> <type> <options> <dump> <pass>
    tmpfs /tmp tmpfs nodev,nosuid 0 0
    /dev/sda1 / ext2 defaults,noatime 0 1
    /dev/sdb1 /home ext2 defaults,noatime,user_xattr 0 1
    /dev/sdb2 /usr ext2 defaults,noatime 0 1
    I'm (now) aware that mounting /usr as a separate partition is a bad idea and (having read the "Error when booting with the new initscripts" thread), I have told pacman to ignore updates to the initscripts package (until I figure out how best to work round or fix that issue).
    Shark wrote:Write umount /dev/sdb2 in konsole or unmount partition in gparted by right click on problematic partition and click unmount. Than proced.
    If I type "umount /dev/sdb2" at the prompt, I get the following error:
    umount: /usr: device is busy.
    (In some cases useful info about processes that use
    the device is found by lsof(8) or fuser(1))
    I tried "umount -l /dev/sdb2" to unmount when the device becomes free... but it never does.
    I also booted into GParted, but there is no option to "unmount" /dev/sdb2.  There is a "mount" option in the menu, but it is greyed out.  If I open a terminal window from the GParted Live environment and type "sudo umount /dev/sdb2" I get the following message:
    umount: /dev/sdb2: not mounted
    DSpider wrote:Are you mounting the root drive with "ro" (read only) in fstab?
    No (as shown above).  I don't *think* I've messed anything up with fstab or any other config files -- everything was working perfectly till the netbook shutdown whilst pacman was running.

  • [solved] netctl (/usr/lib/network/network) fails at boot, sometimes

    Hi,
    Since I reinstalled a new HD in my old laptop (8 years old) I have a problem with my netctl-profile: in about 1 in 4 boots the wireless does not connect. I appreciate it if someone could take a look at what happens, because I cannot seem to find the cause because the logs and errors do not give much information.
    Some general info:
    1) Wireless interface is wlan0; I turned off dynamic naming of systemd/udev. Network driver is RT2500pci.
    2) I use an old kernel version, 3.3.8, because any newer version effectively hard blocks the radio signal without any possibility to change this (rfkill etc).
    3) The power saving option of the network interface must be off. An udev rule does this effectively.
    4) The ip link of the wireless interface must be off before netctl can start the network profile.
    5) When the connection fails, I enter "ip link set wlan0 down" and then start the network profile by entering "netctl start Sorryvoordehobo". This *always* works.
    The following logs and outputs perhaps give information about the issue. Particularly the last might be helpful, because it shows that some authentication indeed takes place, but there is no network.
    netctl profile:
    Description='Sorryvoordehobo'
    Interface=wlan0
    Connection=wireless
    Security=wpa-configsection
    IP=dhcp
    TimeoutCarrier=60
    TimeoutDHCP=90
    WPAConfigSection=(
    'ssid="sorry voor de hobo"'
    'key_mgmt=WPA-PSK'
    'proto=WPA'
    'pairwise=CCMP'
    'group=CCMP'
    'psk=1234-etc'
    ExecUpPost='/usr/bin/ntpd -q || true'
    systemctl --failed:
    UNIT LOAD ACTIVE SUB DESCRIPTION
    [email protected] loaded failed failed Sorryvoordehobo
    LOAD = Reflects whether the unit definition was properly loaded.
    ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
    SUB = The low-level unit activation state, values depend on unit type.
    1 loaded units listed. Pass --all to see loaded but inactive units, too.
    To show all installed unit files use 'systemctl list-unit-files'.
    systemctl status -l [email protected]:
    [email protected] - Sorryvoordehobo
    Loaded: loaded (/etc/systemd/system/[email protected]; enabled)
    Active: failed (Result: exit-code) since Tue 2013-12-17 21:19:04 CET; 3min 26
    s ago
    Docs: man:netctl.profile(5)
    Process: 176 ExecStart=/usr/lib/network/network start %I (code=exited, status=
    1/FAILURE)
    Main PID: 176 (code=exited, status=1/FAILURE)
    dmesg:
    [ 2.879915] Adding 255996k swap on /dev/sda2. Priority:-1 extents:1 across:255996k SS
    [ 3.001917] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: data=ordered
    [ 3.037816] systemd-journald[90]: Received request to flush runtime journal from PID 1
    [ 3.210237] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x1f0-0x1f7 0x290-0x297 0x370-0x377
    [ 3.212449] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x3e0-0x3e7 0x3f0-0x3f7 0x400-0x40f 0x4d0-0x4d7
    [ 3.213304] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: excluding 0x820-0x87f
    [ 3.213995] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
    [ 3.215231] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xc7fff 0xcc000-0xd3fff 0xe0000-0xfffff
    [ 3.215280] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: clean.
    [ 3.215324] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: clean.
    [ 3.215367] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
    [ 3.400147] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
    [ 3.401565] Registered led device: rt2500pci-phy0::radio
    [ 3.401645] Registered led device: rt2500pci-phy0::quality
    [ 3.401959] snd_via82xx 0000:00:11.5: setting latency timer to 64
    [ 3.586063] psmouse serio4: synaptics: Touchpad model: 1, fw: 5.1, id: 0x8f40
    b1, caps: 0x80471b/0x0/0x0
    [ 3.625577] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/seri
    o4/input/input6
    [ 9.541467] Installing knfsd (copyright (C) 1996 [email protected]).
    [ 9.690039] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery d
    irectory
    [ 9.690680] NFSD: starting 90-second grace period
    [ 10.513803] wlan0: authenticate with 00:1a:70:9e:3a:70 (try 1)
    [ 10.515334] wlan0: authenticated
    [ 10.527175] wlan0: associate with 00:1a:70:9e:3a:70 (try 1)
    [ 10.529457] wlan0: RX AssocResp from 00:1a:70:9e:3a:70 (capab=0x411 status=0
    aid=4)
    [ 10.529464] wlan0: associated
    [ 10.529472] wlan0: moving STA 00:1a:70:9e:3a:70 to state 1
    [ 10.529476] wlan0: moving STA 00:1a:70:9e:3a:70 to state 2
    [ 10.577870] Intel AES-NI instructions are not detected.
    [ 11.367009] wlan0: moving STA 00:1a:70:9e:3a:70 to state 3
    Any ideas as to what exactly fails here? Thanks!
    Last edited by anadyr (2013-12-21 21:32:44)

    I don't think there is anything wrong with the kernel. Note that with the previous HD everything started perfectly, with the same kernel version. The new HD is a lot faster as it is an SSD; maybe this has anything to do with the issue?
    To continue: the connection always works when I manually enter "ip link set wlan0 down" and then start netctl. I figured that I should execute this command before netctl starts, but I cannot seem to get this to work. What I tried is to edit /etc/systemd/system/netctl.service, by entering this command with the options ExecStartPre and ExecStartPost (see the two commented lines):
    [Unit]
    Description=(Re)store the netctl profile state
    Before=network.target
    [Service]
    Type=oneshot
    RemainAfterExit=yes
    #ExecStartPre=-/usr/bin/ip link set wlan0 down
    ExecStart=-/usr/bin/netctl restore
    #ExecStartPost=-/usr/bin/ip link set wlan0 down
    ExecStop=/usr/bin/netctl store
    KillMode=none
    [Install]
    WantedBy=multi-user.target
    Nevertheless, with either of these lines uncommented I get boots without the netctl-profile starting.
    In the original post I did not give the output of ip link. So here it is:
    1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN mode DEFAULT
    group default
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group
    default qlen 1000
    link/ether 00:40:45:25:dc:4b brd ff:ff:ff:ff:ff:ff
    3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DORM
    ANT group default qlen 1000
    link/ether 00:13:d3:6c:f3:78 brd ff:ff:ff:ff:ff:ff
    To conclude: authentication succeeds (see the output of dmesg), but I do not seem to get an IP-address (see above). But I have no idea why, and the error messages are not very clear.
    I am still figuring out what happens here, but maybe somebody knows what goes wrong here? Thanks!

  • Netcfg2 not providing menu during boot

    Hi,
    I've spent the morning configuring netcfg2 on my system, and it's certainly easier than my last experience with Ubuntu Server.
    I have no problems connecting when running the #netcfg2 wireless (where wireless is my configuration).  My issue is that this command needs to be run as root, manually.
    The instructions and what I have gleaned off of forum posts indicate I should disable the network daemon in /etc/rc.conf, as it isn't needed anymore.  I also have ensured NETWORKS=(menu) or NETWORKS=(wireless) so that the menu or just the wireless comes up during the boot process.  Except no menu comes up, and neither does the wireless during boot.
    Some context:  I'm running this old IBM thinkpad i1500 (celeron 450MHz) without a GUI, to force myself to learn eLinks, Mutt, vim and w3m, so my goal is to have the network connect during boot, so I don't have to use root or su.
    I have somehow missed whatever config setting launches the NETWORKS=(menu) as part of the boot process.  Any suggestions?
    Thanks,
    Rob

    Hi.
    What about, instead of using NETWORKS=(menu), having one of the startup scripts (rc.local or similar) run /usr/bin/netcfg-menu?  You can also try asking in the netcfg2 thread; I think iphitus is monitoring that thread for questions and problems:  http://bbs.archlinux.org/viewtopic.php?id=43863.

  • How to mount network drive on boot up

    I'd like to mount a network drive on my OS X v10.6 system during the *boot sequence* so that the drive is available to Time Machine to write its backups there. I can mount the drive manually and know how to add it to an user account's loginn items so that it gets mounted when that user logs in. But I want it always mounted regardless of which user is logged in or even if no user is logged in. That way TM can run whenever it needs to.
    So how can I mount the network drive during boot up?
    The network drive is on a machine running OS X v10.5.
    This related thread was my original question in the Time Machine forum: http://discussions.apple.com/thread.jspa?threadID=2807393&tstart=0
    Message was edited by: NikD

    not sure it will work for you but you could try this:
    if you are comfortable with AppleScript, you could edit this script to suit your situation:
    try
    mount volume "afp://<devicename>.local/<volumename>" as user name "<accountname>" with password "<accountpassword>"
    end try
    this script just places the drive's icon on the desktop.
    save it as an application and add that to the account's login items.
    credit for the script goes to Tesserax.

  • Dhcpcd fails at boot (SOLVED)

    Hi peoples.....
    this is a very common problem in arch so i've seen, but i followed many instructions and looked at the wiki,
    and so far i can't fix it....
    when i boot into arch... when it gets to "network" it says busy... and ends up failing... dhcp fails.........
    to get internet working, i have to open a konsole, log in as root, and enter "dhcpcd" then my internet works....
    i've tried quite a few suggestions... such as adding to my /etc/rc.local file... which is this:
    #!/bin/bash
    # /etc/rc.local: Local multi-user startup script.
    dhcpcd -k eth0 dhcpcd -nd eth0
    here is my rc.conf file which to me, looks right
    # /etc/rc.conf - Main Configuration for Arch Linux
    # LOCALIZATION
    # LOCALE: available languages can be listed with the 'locale -a' command
    # HARDWARECLOCK: set to "UTC" or "localtime"
    # USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
    # TIMEZONE: timezones are found in /usr/share/zoneinfo
    # KEYMAP: keymaps are found in /usr/share/kbd/keymaps
    # CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
    # CONSOLEMAP: found in /usr/share/kbd/consoletrans
    # USECOLOR: use ANSI color sequences in startup messages
    LOCALE="en_US.utf8"
    HARDWARECLOCK=""
    USEDIRECTISA="no"
    TIMEZONE="Australia/Perth"
    KEYMAP="us"
    CONSOLEFONT=
    CONSOLEMAP=
    USECOLOR="yes"
    # HARDWARE
    # MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
    # MOD_BLACKLIST: Prevent udev from loading these modules
    # MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
    # NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
    MOD_AUTOLOAD="yes"
    #MOD_BLACKLIST=() #deprecated
    MODULES=()
    # Scan for LVM volume groups at startup, required if you use LVM
    USELVM="no"
    # NETWORKING
    # HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
    HOSTNAME="archbox"
    # Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
    # Interfaces to start at boot-up (in this order)
    # Declare each interface then list in INTERFACES
    #   - prefix an entry in INTERFACES with a ! to disable it
    #   - no hyphens in your interface names - Bash doesn't like it
    # DHCP:     Set your interface to "dhcp" (eth0="dhcp")
    # Wireless: See network profiles below
    #Static IP example
    #eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
    eth0="dhcp"
    INTERFACES=(eth0)
    ROUTES=(!gateway)
    # Routes to start at boot-up (in this order)
    # Declare each route then list in ROUTES
    #   - prefix an entry in ROUTES with a ! to disable it
    gateway="default gw 192.168.0.1"
    ROUTES=(!gateway)
    # Enable these network profiles at boot-up.  These are only useful
    # if you happen to need multiple network configurations (ie, laptop users)
    #   - set to 'menu' to present a menu during boot-up (dialog package required)
    #   - prefix an entry with a ! to disable it
    # Network profiles are found in /etc/network.d
    # This now requires the netcfg package
    #NETWORKS=(main)
    # DAEMONS
    # Daemons to start at boot-up (in this order)
    #   - prefix a daemon with a ! to disable it
    #   - prefix a daemon with a @ to start it up in the background
    DAEMONS=(syslog-ng network xorg hal kdm netfs crond)
    I even tried making a profile copied from examples..... which for me... was wired ethernet-dhcp, since im using a wired connection with dhcp...... and trying to connect to it using netcfg then profile name..... here is my profile input
    CONNECTION="ethernet-iproute"
    DESCRIPTION="A basic dhcp ethernet connection using iproute"
    INTERFACE="eth0"
    IP="dhcp"
    and theres also 1 other suggestion that i tried... which was adding "dhcp eth0" to my /etc/rc.d/network but dhcpcd still fails on reboot and i have to keep manually enabling it.....
    any suggestions???
    thanx in advance
    kaddy
    Last edited by kaddy (2009-09-28 15:53:04)

    lol. anybody?????
    I've tried everything in the wiki under networking, i've tried several other suggestions that helped others, but it seems i can only get my internet to work by manually runniny "dhcpcd"
    but it is annoying to do that everytime i boot.....(i wonder if i can make it start during boot...? but how? its not a daemon.....?"
    anyways.....
    more than happy to try any suggestions..... theres bound to be something wrong here... unless dhcpcd is buggy!
    I even tried wicd and couldn't get it to work properly.... but thats another story.....
    I've tried removing ! from gateway in rc.conf...... i've tried moving the hal daemon last, as i found out it can effect other daemons if run before network........
    funny thing is, about 1 out of 10 times, everything starts up ok, with no fails... but after another reboot, back to the norm.
    im out of ideas........
    im almost gonna give up on this issue........ i don't know what else i can try
    Last edited by kaddy (2009-09-27 16:29:00)

  • Network fails upon load, run dhcpcd and it gets an ip and works

    Here is my /etc/rc.conf:
    # /etc/rc.conf - Main Configuration for Arch Linux
    # LOCALIZATION
    # LOCALE: available languages can be listed with the 'locale -a' command
    # HARDWARECLOCK: set to "UTC" or "localtime"
    # USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
    # TIMEZONE: timezones are found in /usr/share/zoneinfo
    # KEYMAP: keymaps are found in /usr/share/kbd/keymaps
    # CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
    # CONSOLEMAP: found in /usr/share/kbd/consoletrans
    # USECOLOR: use ANSI color sequences in startup messages
    LOCALE="en_US.utf8"
    HARDWARECLOCK="UTC"
    USEDIRECTISA="no"
    TIMEZONE="US/Eastern"
    KEYMAP="us"
    CONSOLEFONT=
    CONSOLEMAP=
    USECOLOR="yes"
    # HARDWARE
    # MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
    # MOD_BLACKLIST: Prevent udev from loading these modules
    # MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
    # NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
    MOD_AUTOLOAD="yes"
    #MOD_BLACKLIST=() #deprecated
    MODULES=(forcedeth b43 !bcm43xx snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore !snd_pcsp !pcspkr)
    # Scan for LVM volume groups at startup, required if you use LVM
    USELVM="no"
    # NETWORKING
    # HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
    HOSTNAME="laptop"
    # Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
    # Interfaces to start at boot-up (in this order)
    # Declare each interface then list in INTERFACES
    # - prefix an entry in INTERFACES with a ! to disable it
    # - no hyphens in your interface names - Bash doesn't like it
    # DHCP: Set your interface to "dhcp" (eth0="dhcp")
    # Wireless: See network profiles below
    eth0="dhcp"
    INTERFACES=(eth0)
    # Routes to start at boot-up (in this order)
    # Declare each route then list in ROUTES
    # - prefix an entry in ROUTES with a ! to disable it
    gateway="default gw 192.168.0.1"
    ROUTES=(!gateway)
    # Enable these network profiles at boot-up. These are only useful
    # if you happen to need multiple network configurations (ie, laptop users)
    # - set to 'menu' to present a menu during boot-up (dialog package required)
    # - prefix an entry with a ! to disable it
    # Network profiles are found in /etc/network.d
    # This now requires the netcfg package
    #NETWORKS=(main)
    # DAEMONS
    # Daemons to start at boot-up (in this order)
    # - prefix a daemon with a ! to disable it
    # - prefix a daemon with a @ to start it up in the background
    DAEMONS=(syslog-ng network @openntpd netfs hal crond gdm fam alsa)
    I was able to manually place the dhcpcd commands in /etc/rc.local. Why is this necessary, though?

    MarcoRosso wrote:The reason why it is happening is because it is timing out. Thats it for me. Since it says timeout after the status fail message. Unless i am wrong?
    This is unlikely because the OP stated that adding dhcpcd eth0 in /etc/rc.local works. If it was timing out that solution would not work. Unless if the OP modified /etc/conf.d/dhcpcd and set a very low timeout limit, I doubt that is the problem here.
    aglarond wrote:
    I had commented those lines out because the first time I loaded Arch my default gateway wasn't being set, even though I was using dhcp. I commented both of those lines and everything started working. It's possible I messed with something else, though.
    -mS
    I find that hard to believe. When you comment those lines out no gateway would be being set. You probably did not have ! before routes=(GATEWAY), which would then set an incorrect gateway, if you don't use 192.168.0.1.
    @OP
    /etc/rc.d/network should be calling dhcpcd to activate the networking on eth0. You haven't modified /etc/conf.d/wireless by some odd chance have you?

  • Systemd dhcpcd service failing on boot

    Hi folks,
    I'm trying to convert my workstation to "pure" systemd configuration (no initscripts-systemd):
    [csingley@quadrupel ~]$ pacman -Qs systemd
    local/libsystemd 185-3
    systemd client libraries
    local/systemd 185-3
    system and service manager
    local/systemd-arch-units 20120612-5
    Arch specific Systemd unit files
    local/systemd-sysvcompat 185-3
    sysvinit compat for systemd
    local/systemd-tools 185-3
    standalone tools from systemd
    Per the instructions on the wiki, I enabled [email protected], but the service fails to start upon boot.
    [root@quadrupel csingley]# systemctl status [email protected]
    [email protected] - dhcpcd on eth0
    Loaded: loaded (/usr/lib/systemd/system/[email protected]; enabled)
    Active: failed (Result: exit-code) since Thu, 28 Jun 2012 12:36:16 -0500; 39s ago
    Process: 299 ExecStart=/sbin/dhcpcd -A -q -w %I (code=exited, status=1/FAILURE)
    CGroup: name=systemd:/system/[email protected]/eth0
    However, I can start the service manually after the boot process is complete:
    [root@quadrupel csingley]# systemctl start [email protected]
    [root@quadrupel csingley]#
    Presumably not all dependencies have been satisfied when systemd tries to run dhcpcd during boot.
    I'm very new to systemd; any tips for troubleshooting this issue?
    TIA

    dj-x-cess wrote:
    I have the same problem.
    It seems, at least for my machine, dhcpcd starts before eth0 gets initialized on boot time:
    Sep 05 07:38:39 vostro dhcpcd[180]: version 5.6.0 starting
    Sep 05 07:38:39 vostro dhcpcd[180]: eth0: interface not found or invalid
    Sep 05 07:38:39 vostro kernel: r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
    Sep 05 07:38:39 vostro kernel: r8169 0000:13:00.0: irq 47 for MSI/MSI-X
    Sep 05 07:38:39 vostro kernel: r8169 0000:13:00.0: eth0: RTL8168d/8111d at 0xf9c00000, a4:ba:db:a6:a6:33, XID 083000c0 IRQ 47
    Sep 05 07:38:39 vostro kernel: r8169 0000:13:00.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
    Yes. Same thing here with the latest install. I put "tg3" in /etc/modules-load.d/tigon.conf. Guess it loads it sooner then and now it gets an IP. Couldn't you make dhcpcd wait for eth0 to come up? It looks important, I mean dhcp should work I'm a newbie with Arch, installed it for the first time.
    Here are my logs before the fix (I was looking in /var/log/, but then I found out that there is a journalctl command):
    Nov 14 15:33:40 neimastina dhcpcd[176]: version 5.6.2 starting
    Nov 14 15:33:40 neimastina dhcpcd[176]: eth0: interface not found or invalid
    Nov 14 15:33:44 neimastina systemd[1]: [email protected]: control process exited, code=exited status=1
    Nov 14 15:33:45 neimastina kernel: EDAC MC: Ver: 3.0.0
    Nov 14 15:33:45 neimastina kernel: wmi: Mapper loaded
    Nov 14 15:33:45 neimastina kernel: iTCO_vendor_support: vendor-support=0
    Nov 14 15:33:45 neimastina kernel: tg3.c:v3.124 (March 21, 2012)
    Nov 14 15:33:45 neimastina kernel: EDAC MC0: Giving out device to 'x38_edac' 'x38': DEV 0000:00:00.0
    Nov 14 15:33:45 neimastina kernel: tg3 0000:34:00.0: eth0: Tigon3 [partno(BCM95751A519FLP) rev 4201] (PCI Express) MAC address 00:10:18:53:12:b7
    Nov 14 15:33:45 neimastina kernel: tg3 0000:34:00.0: eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
    Nov 14 15:33:45 neimastina kernel: tg3 0000:34:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
    Nov 14 15:33:45 neimastina kernel: tg3 0000:34:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit]
    Nov 14 15:33:45 neimastina kernel: gpio_ich: GPIO from 195 to 255 on gpio_ich

  • Network fails every other boot [SOLVED]

    I seem to have a small prob when I startup my pc the network fails every other time. I had some probs w/ dhcp starting when I used gentoo, and found a workaround, putting "dhcpcd -k" in etc/conf.d/local.stop ran the dhcpcd -k command when I shutdown my pc, apparently arch's syntax is a bit different so I doubt etc/conf.d/local.stop exists, I tried /etc/rc.local.shutdown, but that didn't seem to do it either. Could someone please tell me the arch way to enter this command every shutdown?

    Snowman wrote:
    Haiyadragon wrote:
    I'm having the same problem. My motherbord has two network devices. It seems that the designations (eth0 and eth1) switch every boot. So every other boot eth0=dhcp is the right one.
    Will "dhcpcd -k" fix it?
    Check this: http://wiki.archlinux.org/index.php/Ude … _Each_Boot
    Thanks.
    Altough I find it quite weird they switch like that.
    "Because udev loads all modules at once, devices are sometimes initialized in a different order. For example, with two network cards, you may notice they switch designations between eth0 and eth1"
    Yeah, I don't buy it. They switched every boot.
    I'm trying the udev-sanctified method. Will find out in a day or so (when I (re)boot).

  • RV180 (wired only) problems with firmware 1.0.4.14, fails to boot correctly + LAN ports power off during boot (downgrading to 1.0.3.10 = fine again).

    Hi All,
    A few months ago when 1.0.4.14 was released I was quick to update to this version from 1.0.3.10 but very quickly ran into issues.
    Bit of background info...  I am not doing anything complex with this box, basic IP4 network over all LAN ports, no VLANs, firewall enabled and allowing 2 port access rules to a static IP address.  Any static IPs are assigned manual at host level but all other devices receive DHCP IP addresses.  I don’t host VPN on this RV180 but I do with another.  Routing VPN has no issues. WAN is connected to another switch provided by my ISP who provides DHCP IP Address with their DNS etc.  Only LAN ports 1 and 2 are connected, port 1 to my Wireless AP (AP mode passing all requests to the RV180, DHCP etc.), port 2 connects to a 8 port Smart Switch (but all 'Smart' features are currently not in use, so basic switching only).  All other settings on the RV180 are on recommended defaults.
    Everything is working fine on 1.0.3.10 but I have all kinds of issues after updating to 1.0.4.14.  Here are the actions and experiences I had...
    1) Backup my RV180 config to txt file.
    2) Navigate to the firmware upgrade page and follow steps to complete the upgrade process from 1.0.3.10 to 1.0.4.14.  *router does the normal process of upgrading*
    3) RV180 reboots to complete but doesn’t come back up even after waiting 5-10 mins.   LAN ports enable during boot up (link lights on) but after about 2mins turn off (no link lights).  WAN light is on alongside the Power Light.
    4) Power cycle even with rest... Same results.
    5) Reset the RV180 to default settings.  I can sometimes get the unit to boot up and the LAN remains active and powered up.  The web UI is VERY slow compared with 1.0.3.10.  Internet sometimes works and sometimes doesn't (I would expect it all work without issue on default settings).
    6) I repeat this a few times, various resets, powered off waiting periods, etc. but I always have issues.  I did manage to get some log file information and the Kernel appears in the Alert, Error and also the Warning logs (please see attached files).
    7) I gave up at this point.  No major issues like this reported on the internet from a few google searches etc.  So I then reset to defaults (1.0.4.14), downgrade to 1.0.3.10 and finally reset to defaults again + restore backup config settings (with some manual changes).
    The router has remained like this and seem to be working fine, but I would like any security improvements from 1.0.4.14 firmware on my device.
    Anyone able to help, have the same issue or can advise me in any other ways?
    I see 1.0.3.10 isn’t displayed as a firmware download on the standard support page for the RV180 now.  Only 1.0.2.6 and 1.0.4.14.  Do I need to downgrade again to 1.0.2.6 before upgrading to the latest version?
    Regards,
    ~FAZ~

    Hi,
    I recently bought a RV180 router and immediately I encountered the same problem; practically I am not able to access the web GUI.
    The PC is directly connected to the router, nothing else is connected; the TCP/IP configuration is as follows:
    PC: 192.168.1.100
    RV180: 192.168.1.1
    GATEWAY: 192.168.1.1
    SUBNET MASK: 255.255.255.0
    Once the router is turned on, the power LED flashes fastly, the Ethernet LED is on but after few minutes it disappears and the PC detects a disconnection of the Ethernet cable.
    The router is not pingable and, as I said, the web interface is not reachable.
    I have tried to power cycle the router, to reset it (pressing the reset button for more than 3 second and for more than one minute), to access the rescue mode and download a new firmware through TFTP, but nothing worked.
    Few times, after many boot and reset trials,I was able to access the web interface and in one of these occasions I updated the firmware to 1.0.4.14 but once the router is powered off the problem arises again at the next power on.
    I have not tried yet to downgrade to an older firmware version.
    Can you suggest any solution? thank you.

  • [SOLVED] Boot problem - network fail

    Hi
    This is my first time to use ArchLinux. I have used for 3 years Ubuntu and now i feel to step forward in my computing life. So, my first problem is that when i boot my computer network fail - so it writes (i use wireless atheros - i have laptop). When i login i can connect via wpa_supplicant to internet via router without problems. What am i doing wrong?
    Some excerpts from rc.conf:
    MODULES=(fuse network usblp)
    #Static IP example
    #eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
    eth0="dhcp"
    wlan0="dhcp"
    INTERFACES=(eth0 lo wlan0)
    gateway="default gw 192.168.0.1"
    ROUTES=(!gateway)
    DAEMONS=(dbus network @syslog-ng netfs @crond)
    Last edited by Shark (2011-03-01 11:13:22)

    Hi
    Thx for responding
    I follow this site http://www.cdavis.us/wiki/index.php/Ins … Networking and my rc.conf look like this now:
    MODULES=(fuse usblp)
    eth0="dhchp"
    wlan0="dhcp"
    INTERFACES=(eth0 wlan0)
    DAEMONS=(syslog-ng dbus hal !network netfs crond alsa gdm networkmanager)
    Then i did "gpasswd -a username network" and everything works fine now.

  • G580 Upgrade to Windows 10 failed in the SAFE_OS phase with an error during BOOT operation

    0xC1900101-0x20017 I could not successfully upgrade from windows update, nor from the straight download site.   The installation failed in the SAFE_OS phase with an error during BOOT operation.  I see w10 bios updates for other models.  Has anyone been successful in upgrading to W10 from W8?

    2015-07-31 21:36:19, Error CDiagnosticsHelper:etSQMDatapoint: Attempting to set a datapoint in an invalid SQM session
    2015-07-31 21:36:19, Error CDiagnosticsHelper:etSQMDatapoint: Attempting to set a datapoint in an invalid SQM session
    2015-07-31 21:36:21, Error MOUPG CDlpActionImpl<class CDlpErrorImpl<class CDlpObjectInternalImpl<class CUnknownImpl<class IMoSetupDlpAction> > > >:uspend(1066): Result = 0xC18001042015-07-31 21:36:21, Error MOUPG CSetupManager::ExecuteInstallMode(656): Result = 0x800705BB
    2015-07-31 21:36:21, Error MOUPG CSetupManager::ExecuteDownlevelMode(376): Result = 0x800705BB
    2015-07-31 21:36:21, Error MOUPG CSetupManager::Execute(222): Result = 0x800705BB
    2015-07-31 21:36:21, Error MOUPG CSetupHost::Execute(370): Result = 0x800705BB
    2015-07-31 21:36:21, Error MOUPG CDlpManager::AsyncSerializeDisable(471): Result = 0x80070216
    2015-07-31 21:36:36, Error CallPidGenX: PidGenX function failed on this product key. (hr = 0x8a010101)
    2015-07-31 21:36:40, Error CallPidGenX: PidGenX function failed on this product key. (hr = 0x8a010101)
    2015-07-31 21:37:02, Error CDiagnosticsHelper:etSQMDatapoint: Attempting to set a datapoint in an invalid SQM session
    2015-07-31 21:37:03, Error CDiagnosticsHelper:etSQMDatapoint: Attempting to set a datapoint in an invalid SQM session
    2015-07-31 21:37:04, Error CDiagnosticsHelper:etDeferredSQMDatapoint: Attempting to set a deferred SQM datapoint in an invalid SQM session[gle=0x000000b7]
    2015-07-31 21:37:04, Error CDiagnosticsHelper:etDeferredSQMDatapoint: Attempting to set a deferred SQM datapoint in an invalid SQM session[gle=0x000000b7]
    2015-07-31 21:37:11, Error CDiagnosticsHelper:etSQMDatapoint: Attempting to set a datapoint in an invalid SQM session
    2015-07-31 21:39:15, Error CDiagnosticsHelper:etSQMDatapoint: Attempting to set a datapoint in an invalid SQM session
    2015-07-31 21:39:18, Error CDiagnosticsHelper:etDeferredSQMDatapoint: Attempting to set a deferred SQM datapoint in an invalid SQM session[gle=0x000000b7]

Maybe you are looking for

  • General Ledger report with Op Bal , Trans Line Items and Closing Balance

    Hi Experts, My clients needs a General Ledger report which should show Opening balance and all transactions line items with closing figure in a single report for a fiscal year in the given date range wise. Can I get a report in standard sap. Waiting

  • Authorization Object Error

    Hi All, I added an object M_MATE_WRK in the master role and generated the profile for derived role as well. The necessary derived roles have the object now. When user runs a custom t-code which needs this object the su53 still shows that access for M

  • TP4 / ADF Rich client demo just downloaded from otn / 41 compiling errors !

    I just downloaded ADF Riche client demo and installed it jdev tp4. Rebuild causes 41 compilation errors and the application is not runnable. Is it a way to solve this ? Some of the errors: Error: cannot read: C:\JDeveloper\myWork\adf-richclient-demo\

  • Planning for 11.5.10 Oracle E-Business Suite Consolidated Update 2 (CU2)

    Hello All, I have instance with version 11.5.10 I want to apply CU2 I am referring document 316366.1 for above. I found many patches are there. So my question can I apply 2 patches everyday after 5.00 p.m. ?? So user can continue their work during wo

  • After 10.6.7 upgrade - Safari Jitters and more

    after 10.6.7 upgrade - safari windows  jitters / (like screen refresh) and calculator now shows blank content in window - no numbers etc. anybody else see this - or know how to fix this?