Dialer Watch List on Pri dialer????????

Dear All,
I have a 2811 router...
In which I want to configure the dialer watch list..
Plz clarify which ip shud we put on dialer watch list...????
Is it the route . plz find the example below..
boot-start-marker
boot system flash c2800nm-entbase-mz.123-8.T11.bin
boot-end-marker
controller E1 1/0
framing NO-CRC4
pri-group timeslots 1-31
interface Serial0/2/0
description
ip address 139.158.79.89 255.255.255.252
encapsulation ppp
fair-queue
interface Serial1/0:15
no ip address
ip accounting output-packets
encapsulation ppp
dialer pool-member 10 max-link 2
dialer pool-member 20 max-link 2
isdn switch-type primary-net5
ppp multilink
interface Dialer1
description
ip address 139.158.79.93 255.255.255.252
encapsulation ppp
dialer pool 20
dialer idle-timeout 2147483
dialer string 08041259117
dialer load-threshold 1 either
dialer watch-group 10
dialer-group 1
no fair-queue
ppp multilink
interface Dialer10
description
ip address 139.158.79.85 255.255.255.252
encapsulation ppp
dialer pool 10
dialer idle-timeout 2147483
dialer string 02240057435
dialer load-threshold 1 either
dialer-group 1
fair-queue 64 32 0
ppp multilink
ip route 10.179.27.0 255.255.255.0 139.158.79.90
ip route 10.179.27.0 255.255.255.0 Dialer1 100
ip http server
dialer-list 1 protocol ip permit
Plz give me the solution for the back up for the serial link...using the dialer watch list..
Thanks...

configuring dialer-watch
~~~~~~~~~~~~~~~~~~~~~
1) check the ip routing table for the particular route for which you have to create a dialer watch and note it down as it is.
2) create a watch list using the command # Dialer watch-list ip < exact mask>
3) go to the dialer interface and bind it using the command # dialer watch-group
4) Bind it to the interface
For more information regarding the configuration of dialer watch follow the url given below ,
http://www.cisco.com/en/US/products/sw/iosswrel/ps1828/products_configuration_guide_chapter09186a00800872ed.html#18075
4)

Similar Messages

Multiple entries in dialer watch-list

Hi,
If I have multiple entries in my dialer watch-list:
dialer watch-list 1 ip 192.168.10.3 255.255.255.255
dialer watch-list 1 ip 192.168.20.3 255.255.255.255
And just one of the routes gets removed (for example 192.168.10.3) - will this trigger my router to dial the backup link? OR Do both the routes have to be removed before the router will dial?
(Just a little background - the host routes I'm watching are loopback interfaces of head-end MPLS routers and I'd only like the remote router with the dialer watch-list to dial if BOTH loopbacks are removed from the routing table)
Thanks!
Brad

Brad
In my limited experience with dialer watch, I believe that you are going to get the results that you want. Dialer Watch will initiate the backup when all of the specified routes are removed from the routing table.
HTH
Rick

Is there a problem if I use dialer watch without dialer-group?

I use isdn as back up intface,and use dialer watch to monitor.
my configuration is :
interface BRI0/0
description ***To 11.228.244.1***
ip address 11.228.244.2 255.255.255.128
encapsulation ppp
no ip route-cache
no ip mroute-cache
dialer map ip 11.228.244.1 name C-3640-01 broadcast 02080000759
dialer map ip 11.228.8.62 name C-3640-01 broadcast 02080000759
dialer watch-disable 10
dialer watch-group 1
isdn switch-type basic-net3
no peer neighbor-route
no cdp enable
ppp authentication chap
dialer load-threshold 128 either
ppp multilink
dialer watch-list 1 ip 11.228.8.62 255.255.255.255
dialer watch-list 1 ip 11.228.8.61 255.255.255.255
dialer watch-list 1 delay disconnect 10
As you can see,no "dialer-group" command in my configuration.
When I shut down the primary interface,my isdn dialer up correctly,and learn the route from bri0/0.When my primary interface up again,my isdn interface disconnect as expected.
All seems good,so is the "dialer-group" needed in the configuration of dialer watch ?

Hello,
that is actually the default behaviour of dialer watch, it does not depend solely on interesting traffic to trigger the backup. As soon as the primary link goes down, dialer watch brings up the secondary link.
Check the explanation on CCO regarding dialer watch:
Dialer Watch Overview
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fdial_c/fnsprt6/dcdbakdw.htm#wp1000889
HTH,
GP

Dialer watch over Ethernet

I want to use DSL for backup of my MPLS network. I plan to use an external ethernet connected device for DSL access. I plan to use a GRE tunnel over the DSL connection. Can I use dialer watch to bring up the tunnel interface?

I do not know the answer for sure, but I believe that Dialer Watch will not work for the Ethernet/DSL connection. And I wonder why the original post believes that they want it. The motivation for dialer watch is for traditional dial environments where you pay connect time charges and do not want to pay for connectivity when the primary link is available. But with DSL you are not paying connect time charges. You pay the same whether the DSL is actively carrying traffic or not. So why would you want to try to keep the Ethernet or the GRE down while the MPLS was up?
It seems to me that what is needed here is a reliable fail-over mechanism so that traffic is sent over the MPLS when it is available and is sent over the Ethernet/DSL/GRE when MPLS is not available. Without knowing a little more about the environment it is hard to suggest an optimum solution. But I have implemented something that seems a bit similar where DSL/GRE was a backup connection. We ran a dynamic routing protocol over the primary link and over the backup DSL/GRE and configured it so that the protocol preferred the main link and would use the DSL/GRE only when it lost the neighbor relationship on the primary link. It seems like the same approach should work here.
HTH
Rick

ISDN dialer watch feature with

Hi Friends,
Iam running bgp as PE-CE routing protocol with MPLS service provider. we use ISDN for backup, I want to know is dialer watch feature supported with bgp.
regards
ravi

According to the documentation, the dialer watch feature for dial backup is only applicable for EIGRP and IGRP.
The dialerwatch list needs to have an exact match on the route watched and needs to present at the time dialer watch is initialized.
See also:
http://www.cisco.com/warp/public/471/backup_cookbook.html#ts_watch
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/dial_c/dcdbakdw.htm

Dialer Watch failure

All, I have numerous international sites with leased connections that are backed up via ISDN using Dialer Watch. I have noticed that after about a year, the dialer watch stops working. I have performed a "Debug ISDN Events" and cleared the IP route which should trigger the dialer watch, and nothing happens even though the route is not present in the routing table. It almost sounds like there is some kind of memory leak associated with ISDN processes. If I perform a test call or reboot the router everything starts working again. I have noticed this 3 times on 3 seperate platforms; 2600, 2811, and 3640. I am also using various IOS's on each. I scoured Cisco's website and found nothing. Has any experienced anything like this?

Verify that the DDR connection is working properly before you configure dialer watch. Verify there are two dialer map statements on the backup interface.
http://www.cisco.com/en/US/tech/tk801/tk379/technologies_configuration_example09186a0080094143.shtml#troubleshootingdialerwatch

1280 dial call list empty and 2 strange sign ???

1280 dial call list empty and 2 strange sign ???
Already Tried
full flash
full reset
write pm
self test
any solution plz
also tell me about these 2 sign
Attachments:
1280unknownsign.png ‏162 KB
dialempty.png ‏151 KB

The second sign is of headset connected. If it is present without any headset connected then contact Nokia Care. The first sign is not that clear. Is it a lock? Also sice when is the dialled number shown as empty? If its recent you will have to contact Nokia care as you've done all that can be done by a user.
Please mark the post as solution if it solves your problem.
Current Device - Nokia Lumia 1020/920

OK since midday today firefox 3.6.24 apparently no longer executes javascript on ebay. Can't use the "add to watch list" buttons or the enlarge photo buttons. It says 'javascript at the bottom of the firefox window but nothing happens.

just as I wrote above.. ebay loads and functions. I can bid and view auctions but trying to either use the "add to watch list" or "add to wish list" buttons or to switch between different posted photos of an item just gives me javascript:; at the bottom left of my screen but clicking the button has no effect.I'm still running 10.4.11 with the last java download.. is this an ebay change to a newer java version not supported by my os or is it a firefox error..oh and one more thing each page seems to have become 4 times longer..ie there is a huge empty space as I scroll down the page before I hit the bottom.Only appears to do this on ebay..haven't found any other sites showing similar errors and everything works fine on my imac running firefox 4 under 10.5

Craig Stenton: at 12:13:04
but I can't install windows! During the install I am asked for the product key and it tells me that it is not valid and so I can't proceed.
Craig Stenton: at 12:14:16
I can't use the usual methods of activation because I cannot get an activation code. I can't use the activation wizard. I can't call the number because it requires an activation code.
Hi,
I'm a bit confused with this paragraph, as you said Vista already install on your computer, why did you say Windows can't be installed?
According to your description with your problem, it is Product edition and key are not match. Firstly of all, we must make sure the system you installed on your computer was
Windows Vista Business, not matter 32 or 64 bit.
Note: you can check current system edtion at System Properties.
After that, you can try to input your product key and activate your system for test.
If problem still presists, it would be better to provide the activation error message.
Roger Lu
TechNet Community Support

How to create a Watch List using JSF

I'd like to build a HTML UI which includes the toggling of items from a watch list. For example, stocks or system alerts which are important to the user. First of all are there any JSF example which demonstrate this type of application? What is the best approach for building such an interface so that individual lines can be added and removed from the watch list and the view mode can be toggled from watch list only items to all items?
I've looked at the data repeater component example and tried to make that work for this purpose but I'm struggling with some of the details and wondering if the approach taken is good or if there is a better approach. Basically what I have is a List of line items held in a managed bean class. This List is associated to my repeater's value tag. The managed bean also has a UIData element and a UISelectBoolean with the former associated to the repeater's binding and the latter associated to a invisible selectboolean_checkbox (rendered="false").
As the user presses an "Add" watchlist button with an action of toggleWatch the UISelectedBoolean.setSelected (onWatchList) is toggled between true and false for the current UIData.getRowIndex(). However, in tracing the code with a debugger, I see as the component tree is rendered that suddenly all UIData rows appear to have their onWatchList.isSelected() toggled to the new value.
Additionally, when I toggle between the view modes of show watchlist and show all my method to determine what gets rendered doesn't appear to have any effect. This is, when pressing the Show Watch button, the viewType is set to "watch" and then a setRendered method is called to setRendered() for each UIData row as follows. Again, this appears to have no effect.
public void setRendered()
for (int i=0; i< myList.size(); i++)
data.setRowIndex(i);
if ( viewType.equals("watch") && !onWatchList.isSelected() ) <-UISelectBoolean type
data.setRendered(false);
else if ( viewType.equals("raised") && !raised.isSelected() )
data.setRendered(false);
else
data.setRendered(true);
Am I making this too hard or am I just missing something minor???

Upon further debugging it looks like the current issues may be caused by only one onWatchList (UISelectBoolean) existing instead of one for each row in the UIData group. So, what builds the association here? In the RepeaterBean example class the checked UISelectBoolean is simply declared as a instance variable but is never associated to the UIData. How are these glued together?
Of course, I'm still wondering if the is a much better / easier way to get the same results...

Suddenly cannot add items to ebay watch list or view extra photos.

When I click on extra photos, shipping info tab or try to add an item to my ebay watch list nothing happens. I now have to add items from my cell phone. This has never happened before. Had problem for 3 days.

Clear the cache and the cookies from sites that cause problems.
"Clear the Cache":
* Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
"Remove Cookies" from sites causing problems:
* Tools > Options > Privacy > Cookies: "Show Cookies"
Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.com/kb/Safe+Mode
*https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes

Can't get off the watch list

I can't seem to get off the watch list for this forum. Can somone at Sun help?
Thanks,
Tariq

Hello,
Yes, I agree it someimtes annoying.. If I forget to unsubscribe, I'll be reminded when I see next day "Recieving messages 1 of 370..."
Have you tried going to "My Subscriptions", check-marking "GarageBand" category, and clicking "Delete". You may need to refresh the page to view the change you've made in "My Subscriptions" area.
Recently, (I'm not sure if this is your issue or not) I'd been having a problem when I click on "Cancel Subscription to Category" inside the iPod category, which I sometimes subscribe to, it says "You are not logged in, you have read-only access".
My solution to that was:
Logout.
Refresh the page.
Login again.
Refresh the webpage.
Click on "Cancel Subscription to category".
I believe that's what I do when that happens to me (it might be a variant of that, but along those lines).
It's a laborious method I will say, but it does work.
I hope this helps,
-Kylene
If any post helps or solves your issue, please mark it that way accordingly. Thank you for helping the boards!

Cannot open anything in my evay watch list since update

When I go to my watch list in Ebay and click on an item it give me an error message to check item location. If I add something new to watch list I can open it until I have left this page and then it doesn't work again. This works in other browser.

Awesome, thank you very much.

How to vote, add to watch list or comment on a bug in the Java Bug Database

Sorry, could not fine a better place where to post this question.
I'm successfully logged-in but I cannot add a particular bug to my bug watch list, comment on it or vote for it (ok, here I may have already used all my 3 votes but I could also not find where to check this in my profile).
I am particular interested in this bug #4787931:
http://bugs.sun.com/view_bug.do?bug_id=4787931
Thanks for you support!

The Java bug DB was a Sun-time idea. Oracle hasn't put much effort into it since the merger:
- the performance has been horrible, see e.g. {thread:id=2173553}), and it is not clear whether they intend to keep maintaining it as such (open, vote-able,...)
- the "recently closed bugs" page (http://bugs.sun.com/recently_closed.do) seems out of date
- At the time of this writing, I cannot even find a link to log on it from the welcome page http://bugs.sun.com/ :(
Until Oracle openly declares that they will maintain this resource, I wouldn't put much hope nor effort into it...
Much luck,
J.
Edited by: jduprez on Sep 17, 2012 11:59 AM

Strange behavior in watch list

I'm getting a behavior in the watch list that I can't explain. While examining an object in the watch list, its value collumn reads "'VariableName' is not declared. It may be inaccessible due to its protection level." This is from a break
point after it has been declared and initialized. For example:
Dim a As New List()
-- break point here ----
At first I though there was a problem with my custom objects but I get the same thing with any and all framework objects. It does not do this with value objects but if the value objects are declared after the class objects I get the same error. I tried
rebooting and I can't get it back to its normal behavior. Could this be a VS2010 bug?

Today I got the error again even after removing the Linq references. So it may not have anything to do with that. This time I declared a variable like this:
Dim item as List(Of MyTestClass)
When I later used the variable I got the error again. I kept playing around with it when I tried this:
Dim [item] as List(Of MyTestClass)
Now the error went away as long as I referred to this variable with [] everywhere. Then I tried it with a different variable name without the [] and it worked fine. Then on a whim I tried "item" again without the []. This time I could not
get the error anymore. The previous compile had fixed it somehow even though I now had the exact same code that failed previously.
So something seems to trigger it intermitently but I have not clue how to reproduce it now.
Here is another clue. I have a big project (around 10,000 lines of code) targeted for .NET v3.5. When I change the target to .NET v4.0. I get a ton of errors (max number that VS can show) for every variable in my project. "'VariableName' is not declared.
It may be inaccessible due to its protection level." When I go back to v3.5 all errors go away.
I'm starting to wonder if it has to do with the combination of DLL references that I am using. Maybe there is a namespace resolution problem that VS2010 seems to be getting confused when reflecting.

Everyone needs to check their Watch List and Forum Settings

Recently Sun's Java and Developer forums were consolidated into a single, large instance of the Jive forums infrastructure. Some users are no longer getting automatic email notifications on topics they have posted to. If your settings in Developer forums differed from settings in Java forums, then some settings may not be what you expect. Log into any forum, then verify your Forum Settings and Watch List options. In the Forum Profile and Settings, make sure your Watch List Preferances are correct, especially the Email My Watches Updates setting. In Your Watch List, make sure each topic has the Email Updates option set correctly.

Thanks for the info.
K

Dialer Watch List on Pri dialer????????

Similar Messages

Maybe you are looking for