Disable password for privileged Exec mode via Telnet

I've looked around for an answer for this specific issue but haven't been able to find one yet.  Hoping this is easy and someone can point me in the right direction. 
When logging into a 2950 switch via Telnet, I'm prompted for a password when attempting to "enable" privileged mode.  I want to disable the password requirement for now (home lab, not production).  When I initiate the "no enable password" or "no enable secret" command (via a console connection), and try to initiate the enable command, I receive the message "% No password set".  If I now attempt to enable privileged mode from the console, I'm not asked for a password.  How can I disable the password prompt for VTY mode?
Thanks!

Thanks for the suggestion;  I've tried it but am still asked for a password.  
From global config, I entered:
line vty 0 15
privilege level 15
exit
Am I missing any steps there?
Thanks!

Similar Messages

  • ACS 5.3 Different password for privilege exec mode

    This is what I would like to do for our Core Routers. Not too familiar with ACS, so please excuse me if I don't provide you will all the details.
    Right now I have ACS 5.3 which is tide to Active Directory. When a user logs in they use there AD credentials to access the CLI and use that same password to access privileged exec mode.
    What I want to do is have users log in using their AD credentials like normal but have a unique password to access privileged exec mode, different for each user.
    So far this is what I have done:
    1) Created a test user (same as AD user name) in the Internal Identity Store
    Password Type: Internal Users
    normal password set differently that Enable Password (I think Enable Password will only be relevant)
    2) Created a rule under Access Policies > Device Admin - Commands > Identity
    - Created Rule with Current Condition Set    (TACACS+:Authen-Type match ASCII And (TACACS+:Action match Login AND TACACS+Service match Enable))
    - Identity Source: Internal Users
    When I enable the rule. I can login with my AD credentials, but when I try to access privilege exec mode the password that I created for the local user (regular and enable) does not work.
    Question: Do I need to create a shell profile with Maximum privilege value set to something under 15 for the authorization policy and apply it so it will try and use the internal user's enable password?
    Not to familiar with how this works. One of my co-workers said I needed to demote the users in order for my rule to work.

    Hey Tushar,
    That is our current setup. Right now each user logs in with their AD credentials to get into user exec mode and the same password to get into privileged exec mode. I would like to have a user login with their normal AD credentials to get into user exec mode and a different password (specific to each user, not locally on the device) to login to privileged exec mode. We are doing this for security reasons. Hopefully that clarifys what I'm trying to do.
    Thanks

  • How to disable password for Diagnositics

    Hi,
    I want to disable the password option while I am doing Diagnostics. It is asking for password everytime when I select
    Navigation Menu -> Help -> Examine -> Diagnostics
    Please let me know how to disable this.
    Thanks in Advance!!
    Madhu Kumar

    Hi,
    To disable password protection, set 'Utilities: Diagnostics' profile option to 'Yes'.
    Note: 160151.1 - How to Make Help Diagnostics Examine be Password Protected?
    https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=160151.1
    Regards,
    Hussein

  • How to disable password for mount partitions

    Hi.
    I want disable password Aunthenticate for mounting partitions.
    I searched in wiki and google. But nothing found.
    Thanks.

    And/or https://wiki.archlinux.org/index.php/Udisks
    What exactly did you search for?  How did you not find these (and other) results?  Or have you ruled these out?

  • How to reset password for a web user via GUI?

    Hi,
    How to reset password for a web user ID via GUI? is it possible?
    Thanks.

    Hi,
    You can  reset the pwd for the user through trascn SU01.
    BR,
    Disha.
    *Pls reward points for useful answers.*

  • Unable to enter to user Privilege EXEC Mode with catalyst 1900

    Hello
    I am setting up some lab network . I have 10  Cisco 1900 series switches . But when i try to power up it shows the below message. I am not able to get into user privilege mode.
    Catalyst 1900 Management Console
    Copyright (c) Cisco Systems, Inc.  1993-1997
    All rights reserved.
    Ethernet address: 00-C0-1D-81-43-65
    1 user(s) now active on Management Console.
    Enter password:
    Catalyst 1900 - Main Menu
         [C] Console Password
         [S] System
         [N] Network Management
         [P] Port Configuration
         [A] Port Addressing
         [D] Port Statistics Detail
         [M] Monitoring
         [V] Virtual LAN
         [R] Multicast Registration
         [F] Firmware
         [I] RS-232 Interface
         [U] Usage Summaries
         [H] Help
         [X] Exit Management Console
    Enter Selection:
    could you pls tell me how can i get into the user mode such as 
    Switch1#
    Thanks
    Navaz

    There were two versions of software for the 1900 series switches, one that purely menu based configuration and management and the Enterprise version, which had an option to exit the menu and get access to a CLI. Note though that this is not Cisco IOS.
    There's a post, Catalyst 1900 Enterprise software, on the forum from 2002 that will give you some more details. As indicated in that post there's an option to upgrade to the Enterprise edition, but you obviously need to acquire the software.
    As per the reponses from Richard and Leo, these are very old switches and depending upon what you're trying to do with them, may not serve your purpose.
    Regards

  • How to remove password for the recovery mode wizard which you get by pressing command   r while booting mac with mac os 10.10?

    I've set that password long ago and now forgot on how to remove it.
    Should I go to Apple store for this?

    It's possible you set a firmware password, see if the password dialog is similar to the one on this site…
    http://osxdaily.com/2014/01/06/set-firmware-password-mac/
    Those passwords prevent ALL startup key combinations. Confirm it also happens when you boot holding T (target disk mode - How to use and troubleshoot FireWire target disk mode - Apple Support) If that goes to the password dialog you have a firmware password set.
    Apple suggest you take it to an Apple store to get it reset, you can't remove the battery or remove RAM to reset this, so only Apple should reset it.

  • How to disable password for free apps/songs?

    Is there a way to disable having to enter your password in the App Store or on iTunes to download free songs or apps?  I've looked all over in settings, so perhaps I've just overlooked it?

    If you purchase again within 15 minutes of the first purchase it will not ask for your password. After that it will. I don't believe it can be changed.

  • Svrmgrl - disable password for connect internal

    I have installed Oracle 8.1.5.
    When I tried to create a database using svrmgrl manually, I entered the following:
    svrmgrl
    svrmgrl> connect internal;
    Password:
    Please advise how I can turn off the Password option for connect internal as in previous version of Oracle.
    Thanks

    Christian is absolutely right. The user must be a member of the
    dba group which you identified as the default database grup
    during the installation.
    The default is dba. If you chose another group, run the installer
    again and choose Perform Adminstration Tasks, relink the
    executables and try again.
    Peter CARON
    Senior Technical Consultant
    Oracle Internal Training
    Munich, GERMANY
    Christian Pomar (guest) wrote:
    : M.Menzel (guest) wrote:
    : : Hello linux-users,
    : : if i start svrmgrl i have the ora-12546 error, and
    : : i have no idea of the password from user internal!
    : : Whats my fault?
    : : Thanks
    : : Mikel
    : There is not too much information about your problem, but ...
    : are you in the dba group? I you are working directly on the
    : server and you are in the dba group, you should be able to
    : connect as internal with no problem...
    : Hope it helps.
    : Christian Pomar
    null

  • CISCO 700 and privileged EXEC mode

    Hi!
    I have a CISCO 765 and trying to connect to another 765 and the result of the dailing is
    "L08 1 0498291725 Call Connected
    Connection 11 Add Link 1 Channel 1
    Connection 11 Remove Link 1 Channel 1
    L13 1 Disconnecting Call
    L27 1 Disconnected"
    This dosent say so much so I need to enter the debug mode. But how do I do that on the 765?

    Are you getting any other error messages through the console. Try enabling "debug isdn q931" on the router and check for the reason the call is getting disconnected. Check which end is disconnecting the call. Whether it is the calling side or the called side. This will help in narrowing down the issue.

  • Changing default command mode to Privileged EXEC

    I am currently setting up a 2800 Series router, and prefer a username/password type authentication rather than a single enable password. To do this, I did:
    Router(config)# username <myuser> privilege 15 secret 0 <mypassword>
    Router(config)# username2 <myuser> privilege 15 secret 0 <mypassword>
    Router(config)# aaa new-model
    Router(config)# aaa authentication login default local
    This basically does what I want - when I connect to the router through console, it immediately asks me for a username and password. The thing is - as soon as I provide the right credentials, it takes me to USER EXEC mode (the default command mode). Is it possible to change that so that after entering the credentials, I go right into privileged exec mode?
    Bonus question: As it is now, I just have no enable password, so when I login with my credentials, I issue "enable" to enter privileged exec mode without it prompting for an additional password. Is it safe to do it this way - having no enable password but requiring a username and password for login?

    Hi,
    We do this all the time. It works the same way on telnet
    Line vty 0 4
    Priveledge level 15
    This way when we telnet in, it takes us right to priv. exec mode. Most people have the enable password the same as the telnet / console password anyway so IMHO its the same thing. If you are trying to be ultra secure, than make your enable password something different and do not use this little trick....But like I said...I use it all the time.
    Paul

  • ACS 4.2 authentication and Privelged exec mode on Test Router.

    The goal is to have ACS authenticate my username via ssh and allow me to get into privileged exec mode once authenticated. Details below.
    I have ACS 4.2 Solution Engine and I have a test router with the following commands setup:
    aaa new-model
    aaa authentication login default group tacacs+ local
    aaa session-id common
    tacacs-server host 10.4.4.21 single-connection
    tacacs-server key $#$&$*#
    The problem is this. I can SSH and logon to the router which uses a user in the ACS database but the router will not allow me to use the enable command to get to exec mode. The error it gives me is:
    AAA_ROUTER_CLIENT>enable
    % Error in authentication.
    AAA_ROUTER_CLIENT>
    I must be missing something in the ACS. Any help would be appreciated.

    You are missing this command
    aaa authorization exec default group tacacs+ if-authenticated
    This is what you need on router
    Router(config)# username [username] password [password]
    tacacs-server host [ip]
    tacacs-server key [key]
    aaa new-model
    aaa authentication login default group tacacs+ local
    aaa authorization exec default group tacacs+ if-authenticated
    On ACS
    Bring users/groups in at level 15
    1. Go to user or group setup in ACS
    2. Drop down to "TACACS+ Settings"
    3. Place a check in "Shell (Exec)"
    4. Place a check in "Privilege level" and enter "15" in the adjacent field
    Regards,
    ~JG
    Do rate helpful posts

  • How do i reset the password for secure photo video by Easy to Use Apps?

    I have recently upgraded to the newer versions of the free product and am no longer able to log in to the program.  I believe the new version moved from a simple 4-number password to a complex scheme.  However, I can't find any tutorial on how to change to the new system and there is no support for the company (I end up at some web domain sale site when clicking the line in iTunes Store)

    If you haven't already done so then you can reset the password for your iTunes account via http://iforgot.apple.com, and after doing that log out of the account on your iPad by tapping on the id in Settings > iTunes & App Store and then log back in so as to 'refresh' the account on it. And similarly if using the account for iCloud then Settings > iCloud > Sign Out and then log back in
    You say that you 'have a new account', if you have created a new iTunes account then all of your downloads from your old account will remain tied to your old account, so only that account can potentially redownload those purchases for free and/or download updates to its apps.

  • Portal user creation- Disable password Option

    Hi all,
    Can i disable password for all my users.
    we have an option to disable password while creating users.
    i tried creating but it doesnot allow me to login with password field left balnk--it says "Authentication failed. Logon with password not allowed"
    hari

    Hi,
       Disable password doesn't mean you can login without password. It doesn't allow the user to logon directly i.e., This deactivates password-based logon. This means that the user can no longer log on using a password, but only with Single Sign-On variants (X.509 certificate, logon ticket).
    This is useful if you do not require password-based logon because logon is performed exclusively in other ways (such as using logon tickets, see SAP Note 177895). In this case, deactivating the password increases security, as passwords that are not used are usually still initial.Although the deactivation of passwords cannot be made retrospectively, the administrator can define a new initial password at any time.
    Check this out.
    http://help.sap.com/saphelp_nw04s/helpdata/en/f6/0edf3d0eb8af5ee10000000a114084/frameset.htm
    Regards,
    Harini S

  • Want reset my password for my IPAD

    we forgot our password for our IPAD2 ,can i reset it with my ICOULD account ?

    If you haven't already done so then you can reset the password for your iTunes account via http://iforgot.apple.com, and after doing that log out of the account on your iPad by tapping on the id in Settings > iTunes & App Store and then log back in so as to 'refresh' the account on it. And similarly if using the account for iCloud then Settings > iCloud > Sign Out and then log back in
    You say that you 'have a new account', if you have created a new iTunes account then all of your downloads from your old account will remain tied to your old account, so only that account can potentially redownload those purchases for free and/or download updates to its apps.

Maybe you are looking for