Diver conflect on windows 7. How to correct?

I have a new powerbook pro. I have had problems booting into Windows 7. It appears that there is a conflect with my external hardware. When I take all devices out of the loop, Windows 7 boots up and is ok. have one Seagate external hard drive and two Western Digital external hard drive. I also have a LACIE DVD drive, an external logictek keyboard and a Dell flat screen display. One of these devices is causing a problelm. How do I correct the problem external device?
Thanks

You find which one at a time.
And leave it turned off.
Anything that is a Mac array, say WD MyBook with two drives inside? you would need to use MacDrive or not have present.
That is a lot of "stuff" on the desk.

Similar Messages

When I click on a web link and hold down ctrl the page will not open into a new tab, it is just opening in a new window. How do I correct this?

When I use to hold down the ctrl key and left click on a web link, the page use to open into a new tab. For some reason this is not working anymore. Instead when I hold down the ctrl key and left click on a web link, the link will open into a new window. How do I fix this?

I figured out how to correct it. Not sure what exactly was happening. But I started into private browsing and then turned it off. It's been working correctly ever since I did private browsing.

Downloaded safari 5.0.3 to my Windows 7 64 bit operating system. Now screen shows all money amounts in Euros instead of US dollars. How to correct?

I downloaded Safari browser 5.0.3 to my Windows 7 operating system (64 bit) on a desktop computer and now when I look at webpages that show money amounts (dollars and cents) they are all written in Euros instead of american currency. How to correct?

Rysz wrote:
So you are suggesting that Safari does an on-the-go conversion of currency? I don't think so. Safari just displays whatever is coded on the web site.
Localization (Windows settings) might be the culprit, as the user is re-directed to a web-site created for that region. It's also possible, that a foreign web site was chosen or suggested by Google.
Well he states that is all webpages that show any kind of currency. He can go to Control Panel> Region Options> Region & Language Configuration (something like that).
The onthe thing that makes me think that this could be a Safari issue more than a regional issue is that the OP stated that it downloaded Safari 5.0.3, which is not the latest version. This implies to some extent that the installer that was downloaded from a source other than Apple as it is no longer available in Apple's Website (the latest Safari is 5.1.4 which was released today), and there's no certainty on the region from where that Safari 5.0.3 installer was uploaded from which could have very well be a user in Europe; but that's speculation at this point.
Let's see how the issue works out for the OP and then move forward with other possible suggestions

My iMac is connected to a Brother printer. I have Snow Leopard 10.7.3 As of yesterday, when I try to print a PDF it prints as a blank black page. Does anyone know how to correct this so that the PDF will print as I see it on screen?

My iMac is connected to a Brother printer. I have Snow Leopard 10.7.3 As of yesterday, when I try to print a PDF it prints as a blank black page. Does anyone know how to correct this so that the PDF will print as I see it on screen?

If you are running Mac OS X 10.7.3 then you have Lion installed, not Snow Leopard. It's probably not important to this discussion, but something you should be aware of.
What application are you printing the PDF files from? Have you tried opening the PDF file using the Preview application that can be found in the Applications folder? Does the issue still occur? Have you tried other PDF files from a different source?
Another poster in the following discussion thread reported that this method resolved their black blank PDF issue when viewing (and presumably printing) PDF files from Safari.
https://discussions.apple.com/thread/3890509?start=0&tstart=0
This solved my question by mcbuffy on Apr 20, 2012 11:29 AM
There's a solution if you want to see the PDF inside Safari's window :
Go to the folder : Your Hard Drive / Library / Internet Plug-ins.
If you see a file with PDF in its name drag it to the trash.
Quit and restart Safari to test with a PDF.
If it works you can empty the trash.

I have two email accounts, an aol account and a corp. outlook account. When I enable the WI-FI connection I do not receive aol emails, yet I receive the outlook emails on my iphone4. Any ideas how to correct this?

When I enable WI-FI on my iphone4 and connect to my network I do not receive emails from my AOL account, however, I receive emails from my corporate outlook exchange account. When WI-FI is disabled I receive emails from each account. Any ideas how to correct this? Thanks in advance.

Try disabling graphics hardware acceleration. Since this feature was added to Firefox, it has gradually improved, but there still are a few glitches.
You might need to restart Firefox in order for this to take effect, so save all work first (e.g., mail you are composing, online documents you're editing, etc.).
Then perform these steps:
*Click the orange Firefox button at the top left, then select the "Options" button, or, if there is no Firefox button at the top, go to Tools > Options.
*In the Firefox options window click the ''Advanced'' tab, then select "General".
*In the settings list, you should find the ''Use hardware acceleration when available'' checkbox. Uncheck this checkbox.
*Now, restart Firefox and see if the problems persist.
Additionally, please check for updates for your graphics driver by following the steps mentioned in the following Knowledge base articles:
* [[Troubleshoot extensions, themes and hardware acceleration issues to solve common Firefox problems]]
* [[Upgrade your graphics drivers to use hardware acceleration and WebGL]]
Did this fix your problems? Please report back soon.

How to correct "service 'apple mobile device' failed to start" error?

How to correct " service 'Apple Mobile Device' failed to start" error?

How to restart the Apple Mobile Device Service (AMDS) on Windows
Solving MSVCR80 issue and Windows iTunes install issues.

How to correct bad PDF display of Excel 2007 graph-Adobe Pro X?

Just installed Adobe Acrobat Pro X; previously had Adobe Pro 8, which worked fine. Have Excel 2007 files with an Excel graph and a JPG image on the spreadsheet tab. Both the graph and the JPG are too big, are displaced, and hide spreadsheet data, when the Excel file is Saved As a PDF using Adobe Pro dialog or Excel dialog, or the Excel Plug-In to Create PDF. For some strange reason, printing to PDF works, although that is limiting. All of the settings are the same for the Adobe Printer as Adobe Pro settings. Changing them or going to default did not help. Just did the latest update; that did not help.
The graph and JPG are too large for the PDF page. Paper printing from Excel still works fine. Producing a PDF on another machine with Pro 8 still works fine. Could not find this problem discussed anywhere. Using XP, fully patched. This should not be a complicated process, nor a complex spreadsheet. What is going on?
Thanks

Regardless of the method and Adobe product used to create the PDF, including the Excel tool button, the single common factor whether the PDF correctly displays a JPG or graph in the Excel file that is being done at anything other than 100% size is whether the Adobe Printer or a Physical Printer is selected as the default printer in the Windows Printers and Faxes-Settings. This is true even though the printer is not being used. I have created the same PDF using every method/product and the results are always the same, and only properly display when either the setting is 100% size or the system printer is selected as Adobe Printer. This is true only after installing Adobe X (8 was previously installed, and worked as expected).
Jeffry Calhoun
Workforce Analytics Manager
Ohio Department of Job & Family Services
P.O. Box 1618, Columbus, OH 43216-1618
InterAgency: F376, 4020 E. 5th Avenue
614-644-0564
Fax 614-728-5938
[email protected]
OhioMeansJobs.com -
The next best thing to having an HR department.
OhioMeansJobs.com -
Ohio's premier website for connecting businesses and job seekers - quickly, easily, and for free!
>>> "Bill@VT" <[email protected]> 4/7/2012 7:21 AM >>>
Re: How to correct bad PDF display of Excel 2007 graph-Adobe Pro X? created by Bill@VT ( http://forums.adobe.com/people/Bill%40VT ) in Creating, Editing & Exporting PDFs - View the full discussion ( http://forums.adobe.com/message/4319297#4319297 )
You say the settings for the printer work fine, but do not for PDF Maker (I am assuming this is what you meant). PDF Maker no longer uses the printer and the settings are independent. Check the settings for PDF Maker under the create PDF menu.
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4319297#4319297
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4319297#4319297. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Creating, Editing & Exporting PDFs by email ( mailto:discussions-community-acrobat-creating__editing_%[email protected] ) or at Adobe Forums ( http://forums.adobe.com/choose-container!input.jspa?contentType=1&containerType=14&contain er=4697 )
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.
Ohio Means Jobs
You're looking for something unique. Use more than an ordinary site.
http://www.ohiomeansjobs.com
This e-mail message, including any attachments, is for the sole use of the intended recipient(s) and may contain private, confidential, and/or privileged information. Any unauthorized review, use, disclosure, or distribution is prohibited. If you are not the intended recipient, employee, or agent responsible for delivering this message, please contact the sender by reply e-mail and destroy all copies of the original e-mail message.

Main Viewer Window does not display correctly

Ever since I upgraded to Aperture 3.3 through 3.4.1, the main viewer window does not display correctly. Everything is justified to the right of the screen. When viewing images, the are not in teh center, they are over to the right. I can't even see the import controls when trying to import... actually I can't even press the import button or add metada. I am really in a bad position here. Need help with this... anyone out there have a solution please? my clients are waiting for their photos. Yikes!
Right justified?
No Import Controls?
Faces - Everything displayed in a single row, runs off the end of the right side of the screen

Have a read through this page and follow the directions to delete your application preferences,
Let us know how you go.
Tony
http://support.apple.com/kb/HT3805
Message was edited by: Tony Gay

HT1925 I receive error code 2349 when trying to install iTunes. Any idea what that code means and how to correct?

receive error code 2349 when trying to install iTunes. Any idea what that code means and how to correct?

It's a better bet with a 2330, but the first thing I'd try with that is running a disk check (chkdsk) over your C drive.
XP instructions in the following document: How to perform disk error checking in Windows XP
Vista instructions in the following document: Check your hard disk for errors
Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards?

In Fluid Grid layout, I have hidden 2 div for mobile layout. How do I unhide them?

In Fluid Grid layout, I have hidden 2 <div> for mobile layout. How do I unhide them?

Hi there,
I visited your site using Dreamweaver CC and tested it using the default Desktop, Tablet and Mobile sizes, followed by the Smart Phone Size.
The CSS you currently have sets the featurest <div> to 'display: none' when viewed on screen sizes lower than 480px:
Another helpful way to find out what is going on with your CSS is to test the site with Firefox using Web Developer Tools to inspect the element (or alternatively, Adobes Inspect tool). You can right-click the image and "Inspect Element" then resize the browser window so you can see exactly which CSS rule is being applied and overrided.
My suggestion would be to add an additional media query in Dreamweaver to handle all screen sizes below 480px and then set divs or elements you want to hide or show display property to visible.
Hope this helps!

All should read, HOW TO CORRECT SCP on X-FI Fatal

OK, I'll start of by saying I've been having problems with my X-FI Sound Card. SCP especially in Battlefield 2 during an artillery barrage and problems occurred in Rome Total War when the calvary charge was occurring. I spent many months trying to resolve my problem, but in the end I didn't succeed. I even dished out $2500 on a new PC system. I used to have an AMD FX-57 CPU, Gigabyte N-Force 4 Ultra motherboard, X-FI Fatalty sound card, 600 Watt power supply, Corsair DDR 400 (2Gig), and a Geforce 7900 GTX.
The system I just purchased is an ASUS P965 Chipset motherboard, Intel Core 2 Duo Extreme processor, new power supply rated at 600 Watts, DDR2 Memory at 800MHZ using 4-4-4-2 timings, I used the same video card and sound card (Geforce 7900GTX and X-FI Fatalty). Even after purchasing a new system: believe it or not, the same SCP problem occurred in the same games. Note: The new Intel Chipset P965, CPU, power supply, and memory DID NOT CORRECT the SCP problem.
This is how I corrected the problem so far. First, I lowered my speaker volume on my Logitech Z5500 speakers to 40%. Next I went into the Game Console of the X-FI. My adjustments are as follows:
CMSS-3D is disabled
24-bit Crystalizer is enabled and set at 00%
EQ (Equalizer settings from left to right)
0, 6, 6, 3., .3, 2.8, 4.4, ., -2, -2. (Note: 8k and 6k eq settings may cause the SCP, so set them both to -2)
Mixer: Both wave and midi synth are at 80%, all others are disabled
EAX is enabled and set at 2db or 00%
Speakers are set at 5.
Bass Boost is disabled
Master volume is 40%
A few notes:
If volume panel for X-FI starts up (the icon near the system clock)
be sure to right click the icon and select "select audio device" then select X-FI from the menu. I think "Windows Default" is the default value so change it.
I think the EQ (Equalizer) settings really helped out.
Let me know if SCP is cured by setting both 8k and 6k to -2.
Please keep me informed if this helped anybody.
Thanks.

What you just did is to lower the SCP sound level by lowering the medium/high-end of the audio spectrum. It might be acceptable for you, but I don't think enybody else would accept to listen music ao even play games with the sounds over 8kHz attenuated to the maximum. That defeats the purpouse of buying the soundcard - you would be better with on-board.
Try to cancel the Crystalizer (that you have pushed now to 00% and is no use in games anyway) and bring the EQ back to center position (or better - don't use it at all).
About the "windows default" issue - did you disable from BIOS and Windows the on-board sound? It is te first thing to do when you add a Creative soundcard.
Message Edited by SoNic2367 on 09-3-2006 06:27 AM

On my screen my iChat name shows as my AIM handle, but other people are showing a completely different name. Anyone know how to correct this?

On my screen my iChat name shows as my AIM handle, but other people are showing a completely different name. Anyone know how to correct this?

Hi,
I still have you in my Buddy list.
Whereas you were showing just plain "Norma" you are now showing "Norma Howe" in Capital Letters.
The only way I know to achieve that at my end is to View any Display Name that was set up or Add those "First Name, Last Name" Details to my address Book and list your Screen Name against them.
IF the AIM Settings Display Name items does not List NORMA HOWE and in fact lists something else the only thing I can think of is another App allows the Display name to be set from there and this is overriding the AIM Setting info.
I fired up an old version of AIM for Mac (version 4.7 from 2005) on my G4 computer running Leopard.
This Identifies Buddies that have entered Display Names (puts them in the Quotes as in "NORMA HOWE")
In the Preferences of this version of AIM for Mac it has a Sign On tab.
This has a box to enter how you show up (i.e. the Display Name) This version hints at adding Capitalisation and Spaces to your Screen Name.
Actually when I tried to change it to anything this version refused to let me.
So I changed my regular Name to "Ralph Johns r"
This however does not change the AIM settings page
Uploaded with Skitch!
This would suggest that if the AIM setting page does not have this info then it is an AIM app somewhere.
Boot Camp and windows Version ?
AIM for Mac (Any versions) ? (I am prettry sure it will be alter version than mine as the Self Listing shows the changed Name but still lists it as the Screen Name in the info Screen)
AIM on a Phone or iPad ?
8:38 PM Thursday; April 5, 2012
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 iMac 2.5Ghz 5i 2011 (Lion 10.7.3)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
"Limit the Logs to the Bits above Binary Images."  No, Seriously

The color red is turned to rust in Photoshop CS 5. It looks fine in Windows. How can I fix this?

Reds turned to rust in CS 5, Reds are accurate in Windows. How can I correct this.

Good day!
Reds turned to rust in CS 5, Reds are accurate in Windows.
The screenshot you provided seems to show Bridge – which is not Photoshop, but an appplication of its own and for which a Forum exists, too.
http://forums.adobe.com/community/bridge/general
Do the images have their Color Profiles embedded?
Regards,
Pfaffenbichler

I am using system 10.7.3 and my I photo 9.2.3 keeps crashing upon start up. Does anyone know how to correct this without losing my photos?

I am using system 10.7.3 and my I photo 9.2.3 keeps crashing upon start up. Does anyone know how to correct this without losing my photos?

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Console in the page that opens.
Step 1
Enter the name of the crashed application or process in the Filter text field. Post the messages from the time of the last crash, if any — the text, please, not a screenshot.
Important: Some private information, such as your name, may appear in the log. Edit it out by search-and-replace in a text editor before posting.
Step 2
Still in the Console window, look under User Diagnostic Reports for crash reports related to the process. The report name starts with the name of the crashed process, and ends with ".crash". Select the most recent report and post the contents — again, the text, not a screenshot. For privacy’s sake, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.) Please don’t post shutdownStall or hang logs — they're very long and not helpful.

How to correctly use ThinkVantage System Update?

Hello,
I have ThinkPad E520 for two months and I still don't know how to correctly use System Update. From the beginning I've downloaded and installed all updates, but now I want to do it right. How do you do it? Do you install only updates that you need? Or all updates of program that you use? Or just all updates that System Update offers?
Here is interesting sentence: "If it's not broken, don't fix it!". So how?
I don't want to risk and do unnecessary things... But there is a problem with me, that I don't know, which update do I need... So I really need know, how to do it correctly...
Thank you.

Do only use System Update if you have problems with a driver or Thinkvantage Tool - feature.
In my company we never used System update and the laptops are running without any changes (except Windows update) since 5 to 6 years. So i have removed TVSU from all computers.
System Update is a very excellent tool after a clean install from a Windows CD/DVD to install all Lenovo drivers and tools you want to use. A disadvantage of cyclic updates via System Update is, that parts of old drivers in most cases will be kept because the newer driver will be installed over the old one in most cases, which leads after several updates to an instability of the system.
Just my private opinion...
My home-forum: http://www.thinkpad-forum.de
Wiki: Deutsches ThinkPad-Wiki English ThinkWiki
My ThinkPad-Collection

Diver conflect on windows 7. How to correct?

Similar Messages

Maybe you are looking for