DKA790GX Platinum and memory issues
I've had my dka790gx platinum now for approximately 2 weeks.
Build is as follows
DKA790GX-Plat - bios v1.6
AMD Phenom II X4 940
2 x 2gb Corsair Dominator 1066 (5-5-5-15 @ 2.1)
Gigabyte HD 4870x2
Creative X-Fi Extreme GF-PS
Tagan 900BZ
It has been working fine but all off a sudden I started getting the dreaded BSOD in vista 'apc_index_mismatch' and 'memory_management' - I've ran memtest and on the first test @ 45% the system reboots with 4gb of memory in. This happens whether it is running @ 800mhz or 1066mhz, I've also tried 4 x 1gb of corsair xms2 ddr 800mhz and get actually the same issue. If I run 2gb of memory then all tests are ran without any problems and again this is for both the dominator memory running @ 800 and 1066mhz, and also the xms2 memory.
I've then ran another test using the 2 x 1gb xms2 + 2 x 512mb xms2 (all ddr2 800) to give total of 3gb and ensuring all 4 memory slots are populated, and again all tests run fine.
I've tried the memory in ganged mode and unganged mode, but it doesn't make a difference, once i go over 3gb I have the problem, so is this a motherboard fault (i've opened support ticket but had to miss some info as it meant fully stripping down the pc to get hold of the sticker on the side of the pci slot) or a cpu fault seeing the memory controllers are on the cpu?
Quote from: BuD_Sp3NcER on 06-March-09, 03:35:29
As far as overheating is concerned, it really shouldn't be a problem. Before getting a cooler for my RAM, it would get too hot to touch during full load, but would never run into any sort of problem. If you don't believe me have a look at what a SUPER*TALENT Stick looks like: http://www.pcstats.com/articleimages/200702/supertalentT1000UX2G4_full.jpg - Compare that to the dominator, The SuperTalent has to be just about the ugliest MEM-SINK you could ever lay eyes on EXCELLENT RAM though
Kind of a really silly question here: when testing below 4gb, you are testing both sticks, right? I mean they look identical, a small distraction & you're putting the same one back in...happened to me...
yep memory was tested as single chips, also as stated previously testing 4 x 1gb of other memory caused memtest to fail, but 4 x 512mb passed, so did 2 x 1gb + 2 x 512mb
memtest fails all the time when have 4gb of memory in this mother in any combination, but using pc-check all memory passes, if my works had a ddr-2 memory checker then I would have also teste the memory in that as that will pick out memory faults better than any software
Also when the dominator is in slot 1 there is about 1cm between heatsink and dominator fins at the most, so this be a possible cause of the memory getting too hot especially as I would leave the machine on 24/7, but as I've re-setup another machine to do the stuff this machine was doing then i'm hoping i don't see the problem..
Similar Messages
-
DKA790GX Platinum and Gigabyte ATI Radeon 4870X2 2GB
Hi all, was wondering if anyone has had issues with this Gigabyte card in the DKA790GX Platinum. About to purchase but thought I would check here first.
Thank you in advace.
Mark
-MB DKA790GX Platinum
-Bios version 1.6
-Cpu - AMD Phenom2 940
-RAM - Kingstons 2x2G-UDIMM 1066mhz
-Video - Gigabyte ATI Radeon 4870X2 2GB
-Power - Antec Signature 650 +5V 0A 24.0A ±3% 50 50
+12V1 0A 22.0A ±3% 120 120
+12V2 0A 22.0A ±3% 120 120
+12V3 0A 25.0A ±3% 120 120
-12V 0A 0.5A ±7% 120 120
+5VSB 0A 3.0A ±3% 50 50
+3.3V 0A 24.0A ±3% 50 50
+3.3V, +5V max. load: 140W +12V1, 12V2, 12V3 max. load: 43A
+5V, +12V1, +12V2, +12V3 & +3.3V
-Hard Drives: Western Digital 320gb SATA Raid 0
-Windows XP Pro 64bit SP2.I have a gigabyte hd 4870x2 in my dka790gx platinum and it works, just having other problems with getting the board to work with 4gb or more
-
MSI DKA790GX Platinum and AM3 CPU - BIOS Update
Hi,
I am going to upgrade my current computer from an older AMD socket 939 setup to an AMD Phenom II based system
I am thinking of the MSI DKA790GX Platinum motherboard and AMD Phenom II X3 720 (Black edition) CPU (AM2+ Motherboard and AM3 CPU), but I need to clear up the BIOS update for AM3 issue before buying the components.
The motherboard advertisement states that the BIOS has to be upgraded to support AM3 CPU
My issue is this: I do not have an AM2/AM2+ CPU, and I am looking to jump right into buying an AM3 CPU - so will the unit power-up/POST with the combination of the newer AM3 CPU and older BIOS to allow me to update the BIOS using either FDD or Bootable USB Pen in a DOS environment?
Does anyone have any knowledge or experience of this? Any help on this would be appreciated
ThanksQuote from: Scottike on 12-April-09, 00:18:13
The 1.74 Bios is one I got from MSI tech support. We're trying to work through a problem with my new board. nothing major, but we're not quite there yet.
I know that Nvidia was The chipset to have for several years, but I think AMD has upset that applecart a bit with the 780 & now 790 chipsets, and with Intel
getting into the chipset game as well, Nvidia could see some rough times ahead. They may even end up dropping out of the chipset game, since Intel's new CPUs have the memory controller built on die. Hence, Intel has no real need for NVidia any more, Nvidia may end up just focusing on the video card market, unless?
My board defaults to 800mhz as well and I'm running a 720. You have to keep in mind that they have to make the boards default to the lowest common denominator as not everyone runs 1066 capable memory on their board (even though Manufacturers may spec the memory so). I also have to manually bump up the voltage, as well as timings and ratio for 1066. But, my Mushkin ram plugged in and booted with no problems, but I did have to bump up the voltage and tighten up the timings even at 800.
Interesting (Abut BIOS version 1.74). I guess it is not yet available for downloads.
So now Intel CPU's have the memory controller on the die (just like AMD). So does this prove as an advantageous concept? I expect Intel to implement better memory management than AMD. AMD drops speed when all 4 memory banks are occupied... what is the use of utilizing max RAM capability if memory controller cannot sustain the max RAM speed?
I may agree with you on the concept that motherboard should support the lowest (RAM) denominator...
However if someone uses lower than 1066 MHz sticks, system should detect accordingly, and when 1066 sticks are used, auto-detect as 1066... I still do not see the issue here. On former nVidia based boards like my MSI K9A Platinum SLI (with an AMD X2 CPU), 800 MHz modules are detected as 800 on auto, no need to manually tweak anything in BIOS. I still have to see an nVidia EPP profile enabled board which is claimed to auto detect 1066 MHz capable memory sticks by default.
On my system it is also the same... I have to up the RAM voltage to 2.2V (otherwise system is not stable), as well as setting up the timings and of course the RAM/FSB speed ratio to 1:2.66.
I am running currently 4 chips of OCZ platinum 2 GHZ (for a total of 8 GB RAM, for 64 bit Vista and Linux). Also with mine (as we know Phenom II does not support 4 sticks of 1066 MHz) it drops to 800 MHz. As well as, I needed to bump the voltage to 2.2 V... otherwise in the middle of operation, system reboots. We know what this is about, dont we ? -
Firefox 3.6.8 and memory issues
After the last update to 3.6.6, I disabled plugin-container per the instructions given on the forum, and my RAM problems went away. However, after the automatic update to 3.6.8, the memory problems came back, with memory usage going up to 92%. I downgraded to 3.6.4, and turned plugin-container off again; while memory usage is currently at 84%, it is not as low as it was before the upgrade to 3.6.8. (79-80%) (There is very little difference in the websites being opened on the various tabs.)
== This happened ==
Every time Firefox opened
== I upgraded to 3.6.8ffs guys. It's a free browser. It's cool. We love it. But can we do something about memory issues? Almost every release has huge memory leaks.
How about halving the release points and focus on memory issues for the other half of the time. I am a long time user since way back in the day and it seems to me that instead of trying to release so many versions, we should be focused more fixing the current release.
I say put a moratorium on new features until bloat can be fixed. These experiences are starting to give me a hardon for IE again.
Screw new features. I can deal with plain old tabs like they are. I don't need more bells and whistles. This browser has been kicking ass and taking names for a loonnnggggg time. We don't need more bloat. Keep the security fixes coming but everything else can wait. Take a breath. Stop and smell the roses for a few weeks. -
I mean this thing is slooowwww. Many apps crash back to the home screen. I have an app called System and it is showing Wired: 59MB at 36.56% What is this? Apps that are automatically on my iPad? Active shows 2MB at 13.90% and I have nothing running except this app. The reason I am bringing all this up is I was wondering is there any way to speed this iPad up? I mean the memory is atrocious! This thing is slow. And it is a brand new one that I got from the Apple store. Granted, it is not an iPad 2, as I do not have unlimited wealth, as Apple assumes we all do, it is the iPad 1. Maybe the memory issue is having too many apps downloaded? I have absolutely nothing running in the background as I close every app I open because the iPad is so slow and crashes even default email back to the home screen at times! I just want to make this thing faster like the day I first got it. Right now, it is serving as a paper weight as I can't keep anything running for very long. Things run smoothly, yes, but many things do not. Still wondering what this Wired section is, as it is taking up so much of my memory. I have only 88MB free and as soon as I open any app, that diminishes rather quickly.
No it's not jailbroken. I will never do that to any of my devices. I am talking about memory. I have plenty of storage. Just tired of apps crashing back to the home screen.
-
I have a battery and Memory issue - late macbook pro 2011
Macbook Pro 13" Late 2011 Model
Battery Issue
After upgrading to Lion, my batter life is 3 hours after full charge. It was 7-8 hours in leopard.
Hoping this is a common issue and someone has a quick solution.
Memory Issue
I had 4GB Ram and found it would run to virtually nothing and not free any inactive RAM. I though the solution to this was to buy more RAM, which I did.
I now have 8GB RAM and it agains runs to virtually nothing on non labour intensive software like safari or mail. It doesnt free up any RAM when it reaches a certain point. Instead it freezes and I'm forced to restart the computer. I use Final Cut Pro X and Photoshop/Illustrator fairly regualry. I'm assuming the RAM is is used with those but even when these are closed the RAM is low.
Any ideas?
CheersYou should take your Mac to an official apple retail store, as it is not common to have these problems regarding battery and memory.
-
DKA790GX Platinum and Phenom 2 1100T
Hello,
Currently i am running DKA790GX Platinum with BIOS 1.G0 and AMD Phenom 2 X4 965 Deneb C3.
I am going to upgrade my CPU to Phenom 2 X6 1100T Thuban.
The problem is that X6 1100T is not on the list of supported processor by that Board. http://www.msi.com/index.php?func=prodcpu2&prod_no=1552&maincat_no=1
Maximum Supported CPU only 1090T, according to that list.
My question is :
I am in needs to upgrade to more powerful CPU.
(Considering that, X6 1035T - X6 1090T are supported)
will 1100T be working on my Board?
Thanks
When will MSI update the BIOS to support 1100T?
All six cores Thuban are already supported except 1100T.
I think it is not that difficult for MS to edit BIOS and add support for 1100T.
C'mon, i am your loyal customer. Pleaaseee...
Thx -
Neo2 Platinum: 4gb Memory issues
Hi,
I have just installed 2 sets of Corsair TWINX2048-3200C2PT (pair of 1024 MByte DDR SDRAM). This means in total I have 4 x 1gb modules. These are currently running at 2-3-3-6. However the system is only picking up 3gb. I understand the motherboard wont pick up full 4gb but losing a whole gig is madness. I also understand about the single and double sided ram thing aswell. Is there anything to resolve this issue?
Motherboad: MSI K8N Neo2 Platinum
Graphics: Gainward Bliss 7800gs+ 512MB
Sound Card: Creative Audigy 2 ZS
Coolermaster 650W Powersupply
2 X TWINX2048-3200C2PT (4gb RAM)
ChazQuote from: BOSSKILLER on 20-February-07, 20:21:30
Cell Menu, DRAM Configuration, H/W memory hole Remapping & S/W memory hole Remapping available there.
i done this for both H/W memory and S/W memory. It seems that it is now picking up 4gb in the bios but only 3gb in windows.
CHAZ -
FMIS restarting and memory issue
I have Flash Media Interactive Server 3.5.5 on Windows 2008 server. I developed video chat application (many to many), it's only 1 FMS application with about 50-100 room instances and 1 lobby instance to which all users are connected. There are up to 600 - 700 users at a time which produce about 2000-2500 connections to FMS.
Problem I have is with steady raise of memory usage, which if goes little above 2GB will make FMS unresponsive and it would restart itself after about 1-2hours. To avoid that Im restarting FMS manualy every 3-4 days. Interesting thing I noticed is that if I restart FMS from admin console, used RAM memory won't fall at levels as if it would right after whole Windows server is restarted.
In my Application.xml there are following configs:
<Scope></Scope>
<Distribute numprocs="3">Instances</Distribute>
These are things from logs during FMS unresponsive period or right before it:
master.log
2011-05-21 22:01:11 996 (i)2581223 Core (3592) is no longer active. -
2011-05-21 22:01:16 996 (i)2581223 Core (1868) is no longer active. -
admin.log
2011-05-21 22:01:06 2832 (i)2581242 Core (3592) disconnected : _defaultRoot_:_defaultVHost_:::_0. -
2011-05-21 22:01:09 2832 (i)2581242 Core (1868) disconnected : _defaultRoot_:_defaultVHost_:::_1. -
edge.log
2011-05-21 14:22:23 840 (e)2661034 Connect failed ( , -1 ) : Connect failed: (10061) -
2011-05-21 14:23:05 840 (e)2661034 Connect failed ( , -1 ) : Connect failed: (10061) -
2011-05-21 22:01:06 840 (i)2581250 Edge disconnected from core (3592). -
2011-05-21 22:01:09 840 (i)2581250 Edge disconnected from core (1868). -
access.log
session disconnect 2011-05-21 21:29:06 6632 68.191.113.251 29476 39743 - - - - 200 -
session disconnect 2011-05-21 21:29:06 6632 72.198.193.1 4759 6837 - - - - 200 -
session disconnect 2011-05-21 21:29:06 6632 83.70.249.91 11996 14797 - - - - 200 -
session disconnect 2011-05-21 21:29:06 6632 108.8.209.2 57227 76111 - - - - 200 -
session disconnect 2011-05-21 21:29:06 6632 212.183.140.17 3073 3595 - - - - 200 -
Please help me with this issue.Thanks for your answers, I'm replying with delay because I wanted to check these things some more.
When I said 'memory is not less', I meant that total memory in Windows after FMS restart doesn't return to memory levels when Windows is restarted, but I guess that's because of some Windows processes and not connected to FMS.
As for FMS processes, these are the things are notice, few hours after FMS restart I get 1 FMSCore.exe that is around 200-220MB, and 3-4 FMSCore's that are around 40-70MB. Size of that largest FMSCore.exe doesn't go down even when there are much less users connected to FMS. And like I said before, after 3 or more days of running FMS becomes unresponsive, and restarts itself. Right after FMS restart largest FMSCore.exe weights around 70MB but 15mins after it's already 120MB as users connect to video chat application.
As for logs, my core.log files have several lines like:
2011-07-04 03:59:24 3308 (e)2611392 Exception while processing message: Unexpected virtual message from client 6446421578071032403: 93 { # 92 " : t 00 00 00 02 -
2011-07-04 03:59:24 3308 (e)2611029 Bad network data; terminating connection : chunkstream error:message length 12086012 is longerthan max rtmp packet length -
2011-07-04 03:59:24 3308 (e)2631029 Bad network data; terminating connection : (Adaptor: _defaultRoot_, VHost: _defaultVHost_, IP: 94.4.57.121, App: chatcity/stream, Protocol: rtmp, Client: 6446421578071032403, Handle: 2497053121) : 88 1E & D7 FB / 8D 7 99 CB X ...
2011-07-02 14:09:57 1228 (e)2611363 Server detected a backward timestamp from 7990 to 7985 in file: C:\Program Files (x86)\Adobe\Flash Media Server 3.5\applications\chatcity\streams\_definst_\captured_16627033 -
While edge.log has:
2011-07-04 04:58:56 1384 (e)2661034 Connect failed ( , 8134 ) : Connect failed: (10061) -
2011-07-02 21:09:05 6864 (e)2661034 Connect failed ( , -1 ) : Connect failed: (10061) -
And master.log has:
2011-07-04 00:30:27 7128 (i)2581223 Core (6280) is no longer active. -
2011-07-04 00:30:27 7128 (i)2581223 Core (4352) is no longer active. - -
Related to RealtimeThread creation and memory issue
I wrote a sample program
public static void main(String args[]) {
try{
System.out.println("Creating mainScopedMem scoped memory ");
LTMemory mainScopedMem = new LTMemory(10240);
System.out.println("Setup, in memory Area "+ RealtimeThread.getCurrentMemoryArea().size());
new RealtimeThread( null, null, null, mainScopedMem, null,
new Runnable () {
public void run() {
final ScopedMemory orderManagerScope = new LTMemory(240960);
try{
orderManagerScope.enter( new OrderManagerListener() );
}catch( OutOfMemoryError err){
System.out.println("OutOfMemoryError inner Runnable");
err.printStackTrace();
}).start();
}catch( OutOfMemoryError err){
System.out.println("OutOfMemoryError Outer Runnable");
err.printStackTrace();
and executed this code from netbeans, linux in virtual box
-Xms512m -Xmx1024m -Xss1000 -XX:ThreadStackSize=0 -XX:ScopedSize=440960
ulimit -s in linux gave me 10240
I monitored memory via system monitor. I found that my memory started to grow from 786MB to 1.8G
I tried creating a thread pool for 3000 Realtime thread.... My Single CPU got utilized 100% and its used 3.1GB for memory out of 3.3 and code started to hang..
My question is. How much memory does a normal realtimeThread consumes... Is there any limit in creating Realtime thread... and Why does is consumes a lot of memory. If i need to do any fine tuning please do let me know.
Hardware is not an issue in my case....
Right now i am using viritual box. We are running our code in seperate RTLinux box.
- LemuriaHi Ashok ,
Cost Component Structure Applies for both Plan and Actuals ...hence mentioning admin o/h as not relevant for inventory will not serve your purpose.
Only workaround i see it to use a negligible quantity as Admin overhead is routing . Like (0.00001) Hour .
Standard Cost will have a negligible Admin overhead and in actual you will book actual hours will be be part of actual cost
This will solve your Issue..
Regards
Sarada -
I had a customer with a UC540 call approx. three or four days ago, and he couldn't get from his home PC into his work PC via RDP. The work PC is behind a UC540. He restarted the UC540 (power cycle) and it seemed to start behaving.
Today he was having voice quality issues and I noticed a decent amount of jitter on the line (I use PingPlotterPro to monitor his Internet connection). So I had him power-cycle his AT&T U-Verse modem. After that, he was unable to get any Internet connections so he had to power-cycle his UC540.
Things seemed to improve a bit for a while, but then call quality suffered and I started to dig into the UC540 a bit, looking at its built-in diagnostics page. The output on the diagnostics page had this:
UC_540
Home Exec Configure
Syslog logging: enabled (0 messages dropped, 10 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
Console logging: level debugging, 287 messages logged, xml disabled,
filtering disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
filtering disabled
Buffer logging: level debugging, 294 messages logged, xml disabled,
filtering disabled
Exception Logging: size (4096 bytes)
Count and timestamp logging messages: disabled
Persistent logging: disabled
No active filter modules.
Trap logging: level informational, 340 message lines logged
Logging Source-Interface: VRF Name:
Log Buffer (4096 bytes):
DNSOVERLOAD: Low available memory: dropping <id# 37096> from <cli 192.168.10.3>.
000270: Aug 15 22:28:32.467: %DNSSERVER-3-UDPDNSOVERLOAD: Low available memory: dropping <id# 20075> from <cli 192.168.10.3>.
000271: Aug 15 22:28:32.603: %DNSSERVER-3-UDPDNSOVERLOAD: Low available memory: dropping <id# 44542> from <cli 192.168.10.3>.
000272: Aug 15 22:28:33.407: %DNSSERVER-3-UDPDNSOVERLOAD: Low available memory: dropping <id# 39508> from <cli 192.168.10.2>.
000273: Aug 15 22:28:33.467: %DNSSERVER-3-UDPDNSOVERLOAD: Low available memory: dropping <id# 20075> from <cli 192.168.10.3>.
000274: Aug 15 22:28:35.467: %DNSSERVER-3-UDPDNSOVERLOAD: Low available memory: dropping <id# 20075> from <cli 192.168.10.3>.
000275: Aug 15 22:28:36.247: %DNSSERVER-3-UDPDNSOVERLOAD: Low available memory: dropping <id# 11572> from <cli 192.168.10.3>.
000276: Aug 15 22:28:50.224: %SYS-2-CHUNKEXPANDFAIL: Could not expand chunk pool for CCSIP CCB Pool . No memory available -Process= "Chunk Manager", ipl= 6, pid= 1
-Traceback= 8177F9F8z 82FA951Cz 803043E0z 802E9ECCz
000277: Aug 15 22:29:03.652: %DNSSERVER-3-UDPDNSOVERLOAD: Low available memory: dropping <id# 46135> from <cli 192.168.10.3>.
000278: Aug 15 22:29:04.660: %DNSSERVER-3-UDPDNSOVERLOAD: Low available memory: dropping <id# 46135> from <cli 192.168.10.3>.
000279: Aug 15 22:29:05.648: %DNSSERVER-3-UDPDNSOVERLOAD: Low available memory: dropping <id# 46135> from <cli 192.168.10.3>.
000280: Aug 15 22:29:05.848: %SYS-2-MALLOCFAIL: Memory allocation of 736768 bytes failed from 0x82FE819C, alignment 8
Pool: Processor Free: 2282616 Cause: Memory fragmentation
Alternate Pool: None Free: 0 Cause: No Alternate pool
-Process= "Chunk Manager", ipl= 6, pid= 1
-Traceback= 8177F9F8z 82FAB350z 82FCF168z 82FE81A0z 82FA924Cz 82FA9478z 803043E0z 802E9ECCz
000281: Aug 15 22:29:05.848: %SYS-2-CHUNKEXPANDFAIL: Could not expand chunk pool for CCSIP CCB
[snip]
I did a couple of restarts of the UC540 via a telnet "reload" and kept getting that same result. Then I rebooted the PC I was using (which was 192.168.10.3) and made sure CCA wasn't started, then did another reload and now I'm getting this:
UC_540
Home Exec Configure
Syslog logging: enabled (0 messages dropped, 10 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
Console logging: level debugging, 256 messages logged, xml disabled,
filtering disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
filtering disabled
Buffer logging: level debugging, 263 messages logged, xml disabled,
filtering disabled
Exception Logging: size (4096 bytes)
Count and timestamp logging messages: disabled
Persistent logging: disabled
No active filter modules.
Trap logging: level informational, 304 message lines logged
Logging Source-Interface: VRF Name:
Log Buffer (4096 bytes):
Processor Free: 5774524 Cause: Memory fragmentation
Alternate Pool: None Free: 0 Cause: No Alternate pool
-Process= "Chunk Manager", ipl= 6, pid= 1
-Traceback= 8177F9F8z 82FAB350z 82FCF168z 82FE81A0z 82FA924Cz 82FA9478z 803043E0z 802E9ECCz
000245: Aug 15 22:48:51.765: %SYS-2-CHUNKEXPANDFAIL: Could not expand chunk pool for CCSIP CCB Pool . No memory available -Process= "Chunk Manager", ipl= 6, pid= 1
-Traceback= 8177F9F8z 82FA951Cz 803043E0z 802E9ECCz
000246: Aug 15 22:48:56.593: %DNSSERVER-3-UDPDNSOVERLOAD: Low available memory: dropping <id# 19106> from <cli 192.168.10.2>.
000247: Aug 15 22:49:09.914: %SYS-2-CHUNKEXPANDFAIL: Could not expand chunk pool for CCSIP CCB Pool . No memory available -Process= "Chunk Manager", ipl= 6, pid= 1
-Traceback= 8177F9F8z 82FA951Cz 803043E0z 802E9ECCz
000248: Aug 15 22:49:27.947: %SYS-2-MALLOCFAIL: Memory allocation of 736768 bytes failed from 0x82FE819C, alignment 8
Pool: Processor Free: 5231612 Cause: Memory fragmentation
Alternate Pool: None Free: 0 Cause: No Alternate pool
-Process= "Chunk Manager", ipl= 6, pid= 1
-Traceback= 8177F9F8z 82FAB350z 82FCF168z 82FE81A0z 82FA924Cz 82FA9478z 803043E0z 802E9ECCz
000249: Aug 15 22:49:27.947: %SYS-2-CHUNKEXPANDFAIL: Could not expand chunk pool for CCSIP CCB Pool . No memory available -Process= "Chunk Manager", ipl= 6, pid= 1
-Traceback= 8177F9F8z 82FA951Cz 803043E0z 802E9ECCz
000250: Aug 15 22:49:31.595: %DNSSERVER-3-UDPDNSOVERLOAD: Low available memory: dropping <id# 8676> from <cli 192.168.10.2>.
000251: Aug 15 22:49:36.595: %DNSSERVER-3-UDPDNSOVERLOAD: Low available memory: dropping <id# 8676> from <cli 192.168.10.2>.
000252: Aug 15 22:49:45.859: %SYS-2-CHUNKEXPANDFAIL: Could not expand chunk pool for CCSIP CCB Pool . No memory available -Process= "Chunk Manager", ipl= 6, pid= 1
-Traceback= 8177F9F8z 82FA951Cz 803043E0z 802E9ECCz
[snip]
I'm truncating those logs a bit, I'm not sure how many lines helpers here may need telling us we're low on memory.
So I'm not sure how to proceed. After a reload, the SIP trunk takes maybe a call or two, and then I can't call in any more. I'm not sure about calling OUT, I'm remote to the site.
Any ideas on where to start?Hi
I have seen this in the past as well. I recommend the following:
1) Disable DNS Server on UC540, then point all LAN PCs to using public DNS such as Google: 8.8.8.8, 8.8.4.4 This can be done manually for static or by changing DHCP Server scope options
2) Make sure that the firewall is enabled on the UC540 WAN interface
3) Ensure you are using the latest IOS version for the UC540 platform.
It could be that your router is under attack or is participating in a DNS attack via your client computers.
Kind regards. -
I am having trouble. I have a fairly large string buffer that I use instead of a file. The String Buffer can grow to 5-10 MB.
When it grows, it seems that the memory of the JVM basically doubles each time.
To grow the string buffer, I append to it each time, and I have tried making its initial size 1-2 mb for testing purposes.
Is there some way to prevent the jvm from growing it's memory by 2 X each time? It seems wasteful, and when many users are logged in, 10 mb per 10 users gets to be a lot. Please advise??A StringBuffer will indeed double the storage it uses every time an overflow occurs. Given that it has no idea how large its contents will ultimately be, doubling its size on overflow is statistically the best possible approach.
Seems to me, by choosing a StringBuffer instead of a file, you have considered the memory/speed trade-off and chosen higher speed, higher memory instead of lower speed, lower memory. And isn't it true that the issue is mostly that you are using multi-megabytes of memory, rather than that more megabytes of memory are potentially being wasted? If you are only concerned about the extra allocation that StringBuffer makes, you could call its setLength() method to clean up the waste after it reaches its maximum size. -
IMessage and Memory issues since updating iPhone to ios 8.1.3
I stupidly updated my iPhone 5S due to the idea of a wider variety of emojis and now everything has gone wrong. My iMessage keep disappearing and reappearing or not coming through at all on my phone but they're all still coming through perfectly fine on my Macbook. As well as the iMessage issue my iPhone keeps on insisting me memory is full even though I've deleted pretty much everything, nothing loads my screen just crashes then goes back to homepage...my patience is running low and by the looks of Twitter I'm not the only one facing these issue my only wonder now is what, if anything can I do?
Greetings Nezza80,
After reading your post, it sounds like you are experiencing an error when viewing videos. You may want to consider restarting the device first, and then resetting if that does not work. This article provides detailed instructions for Restarting, and Reseting:
Restart or reset your iPhone, iPad, or iPod touch - Apple Support
How to restart
Press and hold the Sleep/Wake button until the red slider appears.
Drag the slider to turn your device completely off.
After the device turns off, press and hold the Sleep/Wake button again until you see the Apple logo.
How to reset
You should reset your device as a last resort and only if you can't restart it.
To reset, press and hold both the Sleep/Wake and Home buttons for at least 10 seconds, until you see the Apple logo.
Thank you for contributing to Apple Support Communities.
Best,
Bobby_D -
890FXA-GD70-Not Posting and Memory Issues
Purchased new 890FXA-GD70 board over the weekend and I am having problems after new build. Board will not post with 2 stick of Corsair DDR3 4GB PC1600 in slots 1 and 2. I removed one stick in slot 2 and board posted. I installed all drivers and Win 7 pro and added the second stick into slot 2 and will not post again. I moved the 2GB stick to slot 3 and the computer boots and seems to run fine. Should'nt DDR3 be run in slots 1 and 2?
System
CPU-AMD Phenom II x4 945
Motherboard-890FXA-GD70
Memory-Corsair DDR3 4GB 2 sticks at 2GB each PC1600 Dual
Video Card-EVGA GTS250 512MB
Hard Drives-Western Digital Black Edition 500Gb
OS-Windows 7 Professional
Power Supply-Corsair 750After checking the boards and google search, it appears that several other people are having the same issue. If the memory sticks are placed in dimm1 and dimm3 the board seems to post and runs fine. But that will not produce dual channel memory. Should I change memory to another brand? What is the best memory for this board. The computer has been running all day and seems to be stable but, just worried that memory is still incorrect and only have 10 days to return to Frys. I have also flashed the bios to 1.6! It appears that after reading several other post on this forum, they had to return the board, could I have a bad board?
-
Fan runs too much i think and memory issue
hi.,I have a gateway gt4016, amd athlon (tm) 64 processor, 3700+ 2.21 GHZ,896 mg of ram
My fan seems to run very often even when its in sleep mode. Also it gets very sluggish at times. i don't have anything running in background, i don't think and when i try to download a video to attach to email it takes forever. Do you know if more memory would help any of this or make things go faster and not sluggish. i have dsl with comcast.Hi there I have the exact same computer as you do. I have it maxxed out on memory (4GB) and I have upgraded the graphics card. Mine ran fine new and after I added the graphics card I noticed the fan ran alot more. I think that is because the graphics card generates alot more heat. When I added the memory everything was much quicker but the fans were the same. It will speed up as you put more demand on the machine. So if you are playing games or doing anything graphic intensive it will cause the fans to speed up. Be sure to have the insides blown out at least once a year and if you have pets at least twice a year. You see dust and pet fur will get inside and settle on components causing them to run hotter and thus the cooling fans will come on alot more to try to keep things cool. Also the fan on the back side up near the top will collect dust and hair, so you need to clean it off once in a while. Mine has been a good machine and never failed as far as hardware goes. Hope this helps you out. Post back and let me know what you find out.
Bob
Maybe you are looking for
-
How to display a html file without tags?
Hello, I am new for Java programming. Now i have to display a html file without all the tags. My code is the fllowing: u = new URL("http://www.ncbi.nlm.nih.gov/entrez/viewer.fcgi?db=protein&val=55584070"); BufferedReader in = new BufferedReader(new I
-
Why Oracle9i statement can not add " ; " in java ?
Hi, I have a following java programme: import java.sql.*; public class Result1 { public static void main(String args[]) { Connection con = null; try { Class.forName("oracle.jdbc.driver.OracleDriver").newInstance(); System.out.println("JDBC drive
-
IPhoto 11 (9.3) Why won't date range work for 2012?
We upgraded to the new iMac and iPhoto 11 a couple weeks ago. The Smart Albums look to have converted correctly, including the ones I created for any one years' photos "All - 2011," "All - 2010," and "All - Best of 2009," etc. Those converted albums
-
my documents are not moving from pages on my iphone to my ipad
-
Hello, I am making a simple address book, and I seem to have come to a block in the road. I have the panel with two different viewstacks, one to show the addresses, and one to add them. I was wondering if anyone could tell me how to set the datagrid