"Do Not use setup Cartridges" message when setting up Officejet Pro 8600

Just trying to set up a new Officejet Pro 8600 and installed the catridges that were in the box but I just get a message on th ediplay that says  "Do not use setup cartridges - Y" and I can't get any further. I've taken them all out and put them back in to no avail.
Can't find any referenct to this error message on HP or google...HELP!!!
This question was solved.
View Solution.

Hi GraGra,
Thank you for the update. Glad to hear the issue has been resolved. Have a wonderful day.
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"

Similar Messages

  • Single Vertical Line When Using ADF for Scan or Copy on HP Officejet Pro 8600

    HP Officejet Pro 8600 Premium Printer (CN577A)
    OS: MS 7 64 bit
    When using the ADF for my CN577A HP Officejet Pro 8600 Premium printer, I get a single vertical line on the document that is produced. This occurs when copying or scanning, both in black and white, and in color. If I scan or copy using the glass, I don't get the vertical line.
    I already tried the troubleshooting.  I unplugged the printer, left it without power for several minutes; that didn't correct the problem.  Next, I cleaned the rollers and the glass; I still get the vertical line, but only when using the ADF.
    My firmware version used is current (CLP1CN1150CR).
    What should I check next?
    This question was solved.
    View Solution.

    The ADF uses its own glass area on the scanner bed, it is the narrow (about 1" wide) strip on the left.  Cleaning this area should resolve the issue.  A single small spot would cause the issue you are seeing.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • How do I tak out the ink cartridge on HP Officejet Pro 8600?

    Need to remove my ink cartridge to buy a set backup.  How do you remove the old cartridge?

    The HP Office Pro 8600 series consists of 3 model variations. I have the Plus version. All functions similiar.
    With the power 'ON', grip the side of the front panel (left handed) just below the HP logo. The entire panel will swing down. The ink cartridge bay will move from the right to the left. Push on the cartridge, and it will pop-out.
    Manual, see pg 13 and 92.    WARNING per HP:    Never turn off the printer when ink cartridges are missing.
    I am a volunteer. I am not an HP employee.
    To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
    The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
    (2) HP DV7t i7 3160QM 2.3Ghz 8GB
    HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
    Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Both Customs use Rosewill Blackhawk case.
    Printer -- HP OfficeJet Pro 8600 Plus

  • Officejet Pro 8600 will NOT print on MAC OSX 10.7.5

    I'm using Mac OSX 10.7.5 
    New Officejet Pro 8600 is set-up and wireless is connected with Bonjour.  When printing the printer utility opens and shows me that the printer is connecting.  For example: "Printing Microsoft Word - Document 1".  Printing page is shown as "100% complete". However, nothing prints.
    I am able to print the 'Print Self Test Page' but nothing else (ie. word documents). I have the printer setup on an HP Laptop and it is working just fine over the network.
    I have tried every solution under the following link and nothing worked:
    http://h10025.www1.hp.com/ewfrf/wc/document?docnam​e=c02205477

    HI, I also had this same issue and finally worked out a solution.
    Just to summarise: I had two Macbooks 10.7.4, iPhone, iPad, airport express and netgear evg2000 router. They all worked wirelessly one minute then stopped. I could wirelessly connect to the printer, print test pages, view the queue, view supplies but any print would appear in the queue as 100% complete or 1% or 12% but never actually print out.
    I logged in to the embedded web server (ews) on the printer, went to network, advanced settings-bonjour and changed the Bonjour Highest Priority Service to '9100 printing' instead of 'LDP'. I then deleted the printer from the print function in system prefs, re added it and it worked. I had to turn the iPhone and iPad off and on and they worked.

  • Officejet Pro 8600 Plus will not print but is connected and says that the print job is 100% Complete

    Hi All,
    I'm printing from a MacBook Pro using OSX Lion. It says that Officejet Pro 8600 Plus is connected and that the print jop is 
    100% complete except that nothing comes out of the printer. I've done all of the test prints and they've printed just fine.
    I tired all of the troubleshooting steps listed on the support guide and still nothing. HELP!

    Not a reply but another plea for help.
    There seem to be so many people with wireless problems that a) it seems silly to start a new thread and b) which one to enter my own plea.
    -Printer bought about 2~3 weeks into Sept 2012
    -Installed onto Macbook Pro running Lion (full updated at that time)
    -Both wireless scanning from printer to computer and initiated from computer worked fine.
    -Printer, with full choice of duplex, layout etc, worked fine. (Even left 5star feedback somewhere!)
    -Set up eprint. That OK, too. Fine from iPad2 and SE Arc S printing photos.
    -Somewhere along the line it stopped communicating with my MBP
    -Out of interest, since there seemed to be no problems with an Acer laptop running Vista, I booted the MBP from an external drive on which I'd done a backup of my 10.6 system iMac (>300Km away: can't try that). Installed HP software from disc. Seemed fully functional. Odd. Very odd.
    -Restarting with Lion on MBP, tried again. Looks as if it might work, but loses connectivity. Tried manual address on printer.
    -Booting from 10.6 system again, reinstalled Lion on MBP (wondering if conflict between HP and Apple updates)
    -Reinstalled HP software from disc.
    Still didn't work.
    -Brought Lion up to date. Downloaded most recent dmg file from HP. Looked for updates. Have applied firmware update to printer
    8600 doesn't list my MBP as available computer to scan to
    [But all the test pages done whilst in HP Utility, and others, get sent through]
    Am getting rather fed-up with all this; never, ever before have I had so much printer problem.
    There seem to be a number of Lion users out there with the same problem. So far -but very infrequently tried- other machines/systems seem OK, therefore I am coming to the conclusion that it is an Apple<> HP conflict. If not sorted soon the printer will be returned as it is not fit for purpose. I'll revert to using my seldom problematic, non duplex A3 Brother.
    Hrumph
    Please help, someone! Either with a pointer to something I've not yet tried or by analysis and rapid availablity of updated software.
    Thanks,
    Mike W

  • Getting following message: hp officejet pro 8600 built-in network capabilities have been disabled

    Getting the following message. I am the administrator and person who setup the printer.  Built in networking capabilities have been disabled. 

    Hey ,  Welcome to the HP Support Forum.  I see that you're encountering a disconcerting message about your HP Officejet Pro 8600 e-All-in-One Printer's network capabilities being disabled.  I would like to assist you with this.  Just for clarity, are you seeing this error message on your PC or the 8600's front panel? Is your printer still connected to your network in light of this error status? Your answers will determine which direction to go troubleshooting-wise.  Please reply at your leisure.  Thank you, 

  • Re: Photosmart 5514; must you use setup cartridges and not standard 564 cartridges during setup?

    Re: Photosmart 5514; must you use setup cartridges and not standard 564 cartridges during setup?

    Yes.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Error message when setting up Road Runner Email on my new Macbook Pro

    I get the following error message when setting up my RR account. 
    Logging in to the neo.rr.com POP server “pop-server.neo.rr.com” failed. Make sure the user name and password you entered are correct, then click Continue. If the information isn’t correct, you cannot receive messages.
    I go to the next steps and everything looks like it should. 
    Help

    Hello Jen,
    Congratulations on your new MacBook Pro!  I understand how important is to have your email account setup on your new computer. I found a couple of resources that I think might help.
    You can check the Mail Setup Assistant for the server settings for common email providers.  I recommend checking your email settings here first to verify they match what you have in the Mail application:
    Mail Setup Assistant
    https://www.apple.com/support/macosx/mailassistant/
    If the Mail Setup Assistant does not provide settings for your email account, you can use the following article when contacting your email service provider to gather the necessary information to setup your account:
    Configuring Mail for your email account
    http://support.apple.com/kb/HT1277
    If you are able to setup your account but messages are not being downloaded, I recommend reviewing the following article:
    OS X Mail: Troubleshooting sending and receiving email messages
    http://support.apple.com/kb/TS3276
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • 3070A setup cartridge message

    Hi I have had a 3070A all in one for a year or so (it is out of warranty). I have just replaced the cartridges, we must have used about 10 sets over the time we have had the printer. The cartridges are genuine HP, although we have used other brands one or twice.
    Suddenly I am getting the message "use SETUP cartridges for initialisation" and it won't print or copy.
    I have tried unplugging the mains and rebooting it to no avail. I have long since lost the setup cartidges.
    Is there any way around this?
    Any help very much appreciated -  I need to print some tickets out urgently!!!
    Thanks

    Thank you for this information.
    Since none of these steps worked, I would recommend contact HP technical support for further assistance. Click here to find out: HP Worldwide Contact.
    I worked on behalf of HP.

  • [svn:fx-trunk] 8732: Do not need to invalidateDisplay list when setting either the horizontalScrollPosition or verticalScrollPostion since the

    Revision: 8732
    Author:   [email protected]
    Date:     2009-07-22 08:00:53 -0700 (Wed, 22 Jul 2009)
    Log Message:
    Do not need to invalidateDisplay list when setting either the horizontalScrollPosition or verticalScrollPostion since the
    ContainerController's setters call updateForScroll(), if scrolling needs to happen, which updates the container.
    Also do not need to invalidate the display list when the scroller calls clipAndEnableScrolling install or uninstall the RET as a viewport.  The scroller should do it if necessary.
    QE notes:
    Doc notes:
    Bugs: SDK-22293
    Reviewer: will be Gordon and Corey
    Tests run: performance tests mentioned in the bug
    Is noteworthy for integration:
    Ticket Links:
        http://bugs.adobe.com/jira/browse/SDK-22293
    Modified Paths:
        flex/sdk/trunk/frameworks/projects/spark/src/spark/primitives/RichEditableText.as

    The same id shows at the top of the Settings > iCloud screen on both your iPad and iPhone - if they are different then they are not being synced. And for contacts and calendars you need Settings > iCloud > Contacts and Settings > iCloud > Calendars 'on' on both devices

  • I keep getting not connected to internet message when i fill out bank forms or back page, i keep getting not connected to internet message when i fill out bank forms or back page

    getting not connected to internat message when i back page or fill out forms

    If you are using Safari, go to the Safari menu bar click Safari / Preferences then select the Autofill tab.
    Click the Edit button next to: Other forms. Click Remove All.
    Back to the menu bar, click Safari / Empty Cache.
    Restart your Mac.

  • Screen Saver does not use selected Screen Saver when activated

    Screen Saver does not use selected Screen Saver when activated. After "Start screen saver" elapse time has been reached, a blank black full screen is displayed. I can activate the selected screen saver by using the hot corners function. Any help with this matter will be greatfully received.

    Hi again sassey,
    You're assuming correctly. Simply change the settings so that your screen saver activates before the sleep settings.
    Hope this solves your problem...

  • I have the iPhone 4 recently became weak Wi-Fi where I can not use the Internet only when sitting Bejjani router, Can anyone help me in solving this problem please iPhone 4, iOS 7.0.3

    I have the iPhone 4 recently became weak Wi-Fi where I can not use the Internet only when sitting Bejjani router, Can anyone help me in solving this problem please
    iPhone 4, iOS 7.0.3

    There's a whole lot to read in your post, and frankly I have not read it all.
    Having said that, this troubleshooting guide should help:
    http://support.apple.com/kb/TS1538
    In particular, pay attention to the mobile device support sections near the bottom, assuming you have already done the items above it.

  • Officejet Pro 8600 not able to be set as default printer

    I've just installed the Officejet Pro 8600 on my wireless network.  It was added correctly using WPS andindicated no problems found on the wireless network test results that the printer did. All items were listed as 'PASS'. It is showing up in the device and printers on my Windows7  64-bit machine. When I right-click on the printer icon, it does not allow me any option to set it as my default printer and it also doesn't show up as an available printer from any application to print (like from MS Office). The device driver was auto-located by Windows, so there is also no option for me to update it. Anyone have a solution for what I need to do to get the printer available to actually print too?? Thanks.

    Hi,
    I had a smiliar problem for the same printer that I bought just yesterday.
    Despite numerous troubleshooting tasks, I was still unable to make the printer my default one.
    I tried
    - switching from wireless to USB connected
    - uninstalling and reinstalling
    - cleaning registry entires as directed here:
    http://h30434.www3.hp.com/t5/Printer-All-in-One-Install-Setup-e-g-Windows-8/Cannot-Set-HP-Officejet-...
    - running troubleshooting wizards and more...
    So... after yet another re-installation, I went here:
    https://h30495.www3.hp.com/help/about
    and clicked on Printer Support under Additional Help (down at the bottom)
    - choose North America
    - choose HP Support - United States (English) --> Product Support and Troubleshooting -
    - now - here - IMPORTANT - http://www8.hp.com/us/en/support-drivers.html :
    DO NOT  Enter a product name/number
    - but choose
    Or automatically find your products and solutions - click on START button
     you may need to ALLOW your antivirus software to scan your computer and after a minute or so you will get a response like this:
    1 HP products were discovered
    »HP Officejet Pro 8600 Plus e-All-in-One Printer - N911g                 Serial Number:                                 Product #  here                                               Product Number:                                 Number here                               
    Now got to Start - Devices and Printers and RIGHT CLICK on the HP printer device and choose Printer Properties:
    The GENERIC NAME  "HP Officejet Pro 8600" needs to be replaced with FULL NAME of your printer:
    HP Officejet Pro 8600 Plus e-All-in-One Printer - N911g
    Click "Apply"  - click OK
    Now make your printer DEFAULT
    GOOD LUCK!

  • HP OfficeJet Pro 8600 - Text Gray not Black - HP Utility Crashes - Hundreds of Ethernet Messages

    I bought an HP OJP 8600 for home use, hoping for quality and speed, and little intervention on my part.  Using the printer from both an HP Windows 7 Laptop, and a MacBook Pro OS X 9.5, but mostly the MacBook Pro.
    I recently started working ten hours a day and weekends at home.  I am printing a lot of letters for business and for work.
    I've got a bit of color blindness toward pastel and light colors, so I always have my artist daughter double check my work when necessary.
    Both of us were looking at a letter I received from a state agency and then looking at my reply letter from the 8600.  The letter from the agency had dark black, clear text.  By comparison my letter looked to have "thinner" text (even using the same font the agency selected) and the text in my letter is noticably gray by comparison.  I get the same results on both computers.
    I double checked all the settings, made sure the print quality is "best" and I even use 98 brightness paper.
    The "HP Utility" made by HP for the MacBook Pro is almost useless.  The HP Utility fills up my folders with CRASH reports, is always running, and the Activity Monitor always shows the "HP Utility" using some unexpected extra amount of CPU.
    With the poor wireless radio on the OJP 8600 I finally shut it off, and connected the printer by ethernet to the router.   But while looking for computer performance problems I used a packet sniffer on the connection.  I found about 40 HP OJP 8600 messages a SECOND sending the same routine information over and over and over.
    My warrenty is up in December.  Do I let it expire and junk the printer?  Or is there a fix for some of these problems?
    I appreciate any suggestions, but please, tell me it is a suggestion if it is.  If you haven't tried it and found it to work please don't tell me "here is a solution."

    Hello @UThrewError ,
    I have read your post as well as your post and thread history. I do have a suggestion for you, in regards to your "quality" issues with your print outs. I would suggest to you, to try the steps listed in this certain guide below to see if the steps help with the quality.
    Fixing Print Quality Problems for the HP Officejet Pro 8600 e-All-in-One Printer
    If they do not help at all, and to add to the history of issues you've experienced, I would next suggest calling HP technical support directly. My reason behind that would be, if the printer is coming up to the warranty end period, and you have had ongoing unresolved problems with the printer, and presently print quality troubles, it's best to have a technician hear about it. If they see fit an in-warranty replacement, they could make that happen with you before the warranty expires. I will leave their contact info below if you decide to call HP.
    HP's contact info:
    If you are calling within North America, the number is 1-800-474-6836 and if you are calling outside of the US/Canada,: click here.
    Best wishes to you, thank you for visiting the forums
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Maybe you are looking for