Dual VXI System Sometimes Locks Up

I have a dual mainframe VXI system and at random times (always during the initialization phase), the green light will stay lit on the 1394 controller in the first mainframe and all communication stops. I'm using VB.Net with NI-VISA. After a lock up, I have to cycle power on the VXI chassis, sometimes more than once to get Resman to run successfully again. Sometimes, Resman will error out and give the message: There is more than one device in frame 0 configured for Slot 0 operation. I was wondering what could happen to cause this message when there is only one controller in each frame? Could something be happening in the software that causes the NI software to think that both mainframes are actually one system?

Are both chassis being powered up simultaneously? If so try staggering the boot sequence, chassis 1 then chassis 2. Also, are you daisy-chaining the second controller off the 1394 ports from the first controller, or do you have both contollers connected directly to the PC? Try connecting both chassis directly to the PC. If you are powering up both chassis at the same time and are daisy-chaining the connection, this might cause some problems.
Michael Chaney
Systems Engineer - TestStand
National Instruments

Similar Messages

System may lock up when playing games

Having a T61P
I had a deffected Planner, I claimed the planner,
and Lenovo changed the Mboard
after 2 days , I found my laptop staked when playing games
I checked lenovo support
and found this website, which stating 100% my problem
http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-69684
refering to the website above, the solution to my problem is :
Contact the help center and reference this tip to get your planar replaced
The issue is that : even the New one they changed(FRU 44C3931) , is giving the same problem
(System may lock up when playing games)
What do you advice
Thanks

This is what OCZ recommends for the board:
Upgrade Configuration for: MSI
Model: MSI 790FX-GD70
System Specs
Type of system:   Motherboards
Bus Architecture:   PCI
CPU Type:   Phenom II X4
Memory Specs
Standard Memory:
Maximum Memory:   16384 MB
Memory Expansion:   4
Model Specs
Model Comments:   AMD 790FX, 2600 FSB, ATX
CPU Comments:   Phenom II X4
COMPATIBLE MEMORY
Description    Mfr SKU/OEM#    OCZ Technology Part No.
512MB, 1066MHz, DDR3-1066 PC3-8500, 240p DIMM, 1.5v
512MB, 1333MHz, DDR3-1333 PC3-10600, 240p DIMM, 1.5v
512MB, 800MHz, DDR3-800 PC3-6400, 240p DIMM, 1.5v
1GB, 1066MHz, DDR3-1066 PC3-8500, 240p DIMM, 1.5v         OCZ310661GB
1GB, 1333MHz, DDR3-1333 PC3-10600, 240p DIMM, 1.5v         OCZ313331GB
1GB, 800MHz, DDR3-800 PC3-6400, 240p DIMM, 1.5v
2GB, 1066MHz, DDR3-1066 PC3-8500, 240p DIMM, 1.5v         OCZ310662GB
2GB, 1333MHz, DDR3-1333 PC3-10600, 240p DIMM, 1.5v         OCZ313332GB
2GB, 800MHz, DDR3-800 PC3-6400, 240p DIMM, 1.5v
4GB, 1066MHz, DDR3-1066 PC3-8500, 240p DIMM, 1.5v
4GB, 1333MHz, DDR3-1333 PC3-10600, 240p DIMM, 1.5v
4GB, 800MHz, DDR3-800 PC3-6400, 240p DIMM, 1.5v
OCZ3P20004GK is not listed. That it won't boot with one stick in slot 1 is telling.
The OCZ configurator is motherboard centered and did not give me an option to select an AMD Phenom II X2 550 Black Edition Callisto 3.1GHz 2 x 512KB L2 Cache 6MB L3 Cache Socket AM3 80W Dual-Core Processor. Still, assuming the processor would handle it, which is a big assumption, it does not appear to be AMD happy ram. You might get a more authoritative answer if you can find a box with same mobo and processor and check that system but I'm thinking you need new RAM.

What do i need to do to share TB and Lightning files between W7 and Ubuntu 14.04 on a dual boot system?

I recently installed Ubuntu 14.04 alongside W7. Since I'm not comfortable dropping Windows completely yet, I want my W7 Thunderbird and my Ubuntu TB to have access to the same data file holding current messages, so I don't have to get out of one to use TB on the other. I rely on Lightning and also want my reminders to be consistent from either OS. I have a separate NTFS data partition which, I understand, can be used to house the profile directory (though I've not seen that as a solution for Lightning).
In trying to set it up, I've run into questions that I can't find a good answer for -- want sources that address the problem and are recent. I'm pretty patient, and I can stumble through a lot of things (like learningn about partitions). But I'm not a programmer, and this start-stop-sort-through-dozens-of-old-incomplete-and-irrelevant-answers process is frustrating. (Nor do I lift the hood and tune my own car engine.) I also recognize that some things I want to do aren't necessarily common, so they're not at the top of anyone's "tell the world how to do this" list.
1. My profiles directory has 6 *.default files. I assume the current one is the most recent. Do I need the older ones? How did I get them, since I've never knowingly created a new one? I'm the only user of my machine and thus the only user for TB.
2. I saw the following before setting up the dual boot system, so it's likely not related -- but if someone who knows TB well can comment I'll appreciate it: when I view All folders, I see 58(!) folders with names nstmp-##. The contents overlap with normally-named folders, but the sets of messages are not identical. Do these indicate a problem and/or should I change something? Does this have to do with compacting or archiving, neither of which I do? Never saw the need, and never saw an article saying that they're important. I just want to use mail and reminders. And BTW I've been using TB/Lightning for years and am Very happy with them, so I want to keep using them.
3. Is there a way to set up Lightning to hit the same data file(s) on my data partition? Or somewhere? Where are Lightning's files? I remember one source mentioned linking to "storage.sdb", but (1) I can't find the reference again, and (2) links to some of my files don't always work. Broken links aren't Mozilla's problem, but someone might know how to geet around the problem for the sake of Lightning. Also, storage.sdb and calendar* directories exist inside my *.default profile directory -- so why would I need to link anything? Are these not where calendar data is stored? If not, where?
I'd rather understand the reasons behind recommended procedures ("do A because Y is how Lightning/TB works" -- vs "do A, then B, then C...and it will/should(!) work."). But if you can point me to a clear procedure that will get me where I want to go, that will be enough.
Last, the following two URLs looked like they would help but don't -- so you don't need to point me to them again:
http://kb.mozillazine.org/Sharing_a_profile_between_Windows_and_Linux -- this is only 2 years old but:
(1) it only says that "settings" specify file locations, without saying which settings. Stumbling around, I found "Local directories" under Server Settings. For more detail the page refers to an article that's 10 years old. Neither source says which subdirectory under *.default should be the target. The older one references ".../mail", but when I enter that value in Local Directories under Ubuntu, nothing shows up. When I went down one more level to "/Local Folders", the folders appear and the new-message counts seem(!) ok. But I also got a couple "folder missing...will adjust filters" messages. I never got those under Windows. So am I good to go, or am I missing messages?
(2) The above page only says that Lightning is a "potential problem", with no suggestion of a solution or link to a discussion. Searching results in many hits, but I haven't found anything helpful.
http://ubuntuforums.org/showthread.php?t=1624973 -- this looked promising, but the comments are dated 2009-2010, deal with ubuntu 10 and XP, and don't seem to address my problem -- unless I'm not savvy enough to recognize it, which is entirely possible.
Thanks for any insights.

Lightning is a problem for you because it hooks into Thunderbird at a low level and you need a version compiled for the platform Thunderbird is running on. So you can't do the preferred solution, which is to put your whole profile in a shared folder and have both instances of Thunderbird reference the same profile. (Ditto for Enigmail). Lightning may become an integral part of Thunderbird in an upcoming release, at which point this limitation due to Lightning should disappear.
And if you can't use a shared profile, you can't set your Lightning, or your Address Book, to share a common set of files. Put another way, the linkage from Thunderbird to its address book files and calendar data is hard-coded, and not exposed where we can adjust it. :-(
The halfway house is to place your mail stores in a shared place, and use the Local Directory setting in each account's settings to connect to it. They don't need to be in the profile; what's more important in your case is that they are in a folder accessible to both operating systems.
Look in your profile; everything under Mail and ImapMail needs to be moved out to a shared folder. Note the entries in Thunderbird under Local Directory before you do this, and reconstruct those pathnames in Thunderbird, but adjusted to suit their new locations.
(You can see here that you need to make many adjustments, one per account, in each instance of Thunderbird, so it's a high-maintenance solution and this is why we don't recommend it when the alternative, moving the whole profile, is possible.)
I share address books and calendars between Thunderbirds on various computers (and my phone and tablet) by syncing to something in the cloud; Google Contacts and Google Calendar are my choices, using gContactSync and CalDav.
Having made the break myself some years ago, I'd recommend you break away from Windows. ;-)

If I buy a new macbook with Apple, will they help me install a dual operating system?

I've heard Bootcamp does this, but I've never owned a Mac before, and am daunted by the change. I would love a Mac for ease of use, as many of my friends seem to love it, but for school purposes, my PC laptop is better. My PC needs to be updated, though, and I really want to spring for the Mac, I just don't want to lose being able to not have to do my homework in a computer lab. A friend has dual operating systems on hers, and says it works beautifully for running both, though I don't know what macbook she's got. If I go to an Apple store and get a laptop from them, even bring the Windows 7 operating system (I'm NOT doing Windows 8), will they help do this for me? Does anyone know if it is alright to have the dual systems, or if it takes away from the hardware's ability to work? ANY advice is welcome.

It is not hard. Boot Camp allows running Windows natively, same as on a laptop PC would be with a few differences in fan and thermal control and drivers.
Once installed natively which would be dual-boot setup, you can then install and use VMware or Parallels to assign the Windows partition for use as a VM inside OS X, no more need to dual boot unless you want to.
All of the information can be printed out from Boot Camp Assistant utility, or from the support help page and link to the manual:
http://www.apple.com/support/bootcamp
Paragon CampTune is a commercial product that is designed expressly for this task. http://www.paragon-software.com/home/camptune/ It consists of a downloadable ISO that needs to be burned to a disc and booted from in order to resize the partitions costs US$19.95.
Mac 101: Using Windows on your Mac via Boot Camp
https://support.apple.com/kb/HT1461
http://www.apple.com/support/bootcamp/
Helpful Apple Support Resources (Forum Overview)
Boot Camp Support
Boot Camp Manuals
Frequently asked question
http://support.apple.com/kb/HT4818
Older Lion version for the manual:
http://manuals.info.apple.com/en_US/boot_camp_install-setup_10.7.pdf

I have a macbook and it is a dual boot system, I would like to be able to see the mac side of the system on a larger monitor. I can hook to a hdmi cable and see the pc side, but not the mac side, any suggestions?

I have a macbook that I bought second hand. The mac has a dual boot system with bootcamp on one side and snow leopard on the other. I would like to be able to hook to a larger hdmi monitor so that in both systems I could see better since on the leopard side the computer has PS4. I have purchased the dvi to HDMI accessory and purchased the HDMI to DVI cable, and can see fine on the bootcamp side, but nothing on the leopard side. Could somebody help me with configuring things so that it will see both side?
Also on a minor note, I need to purchase a new battery for this item and don't know which one to purchase. Any help would be greatly appreciated, especially with the display/monitor issue.
Thanks Sue
ps sorry but the operating system is OS X

When you try to use the Mac side on your external monitor do you get a blank screen or do you see the aurora background?
It would help to know which one of the 9 different models of MacBook you have. To see which model you have go to the Apple in the upper left corner and select About This Mac, then click on More Info. When System Profiler comes up check the Model Identifier and post it back here.

Dual Core Center working in Vista but not XP on a dual boot system?

Hi All.
My system specs are:
Dual Boot Windows XP Pro SP2 and Windows Vista Ultimate
Temps for CPU in Vista averaging at 43 - 45 degrees in XP averaging at 38 to 42 degrees. It never seems to go much higher than 53 on Load.
Thermaltake Soprano tower
MSI K9N Diamond Motherboard
Hiper 580watt Modular PSU
4GB OCZ Gold 6400
AMD X2 6000+
2 X 300gb diamond maxtor 10 HDD
MSI Geforce 7800gt
DVD Rom
LG Dual Layer DVDRW+/-
I am running a dual boot system with Windows XP Pro SP2 on one partition and Windows Vista Ultimate on the other. Both operating systems seem to be operating properly except for an odd situation with Dual Core Center. In Windows XP Dual Core Center only indicates the Mainboard properties - No VGA, whereas on Windows Vista Ultimate Dual Core Center indicates both VGA & Motherboard properties. I have installed MSI Nvidia drivers for the Graphics card & also tried straight Nvidia drivers for the card but it has made no difference VGA will not show up in XP. Yet on installing Dual Core Center on the Vista partition VGA showed up immediately. Can anyone help.
If anyone can come up with an answer to this it would be a real help.
Many Thanks in advance.

have you try to update/install the dual core driver from amd?

How to install PS CS4 64bit in a Dual Boot system

Hi,
I have just created a dual boot system.
Dell XPS 600 3 gig of ram (soon to be 6 gig
Windows XP Pro 32 bit
Windows Vista Home Premium 64 bit
The windows OS can not see above 2 gig (and that is a long story but believe me I have had it confirmed - even though a 32 bit system should be able to see up to 3.5 gig). That is why I created the dual boot (into Vista 64) OS.
The Vista 64 bit OS CAN see the current 3 gig (soon to be 6 gig).
Each has its own partition and I dual boot via a 3rd party BootIt NG
Question:
1. What is the proper way (if I even can do it) install PS CS4 on to the Vista 64 bit (in another partition) to take advantage of PS CS4 64?
2. Do I have to delete the XP 32 bit version and reactivate?
3. I do not use Bridge (or do I have to in order to get the 64 bit)? I have seen some threads here about using Bridge so I was wondering about that.
4. I also have IL CS4, ID CS4 and plan to do the same. Is that possible?
5. I know there is an issue with plugins so I will address that matter as it comes up. Hopefully, though the downloaded brushes will work ok in both the 32 and 64 bit envrionments.
Thanks in advance,
Bob

Thanks for the responses. Perhaps more of an explanation as to what I have done is in order.
I purchased this Dell XPS 600 XP Pro system some time ago. It was a "boomer" (powerful) system in its' day.
I subsequently increased the Ram to 2gb. I also have a internal 160gb 10K (rpm) Raptor and and another internal WD 250bg (7500 rpm) HD. I drive 3 monitors with a Nvidia 6800 and a Nvidia Dual port 7800 Gt.
So, all in all, the system is still (by today's standards) fairly robust.
BUT, with PS CS4, I tried to up the Ram from my installed Windows XP Pro 2gb system to 3 gb (given that every spec in the world says a 32bit system can see a max of 3 to 3.5 gb).
On my system. Wrong. It (the Windows XP My Computer Properties system would not see over 2 gb (even though BIOS said there was 3gb!) Additionally, BIOS said my board was capable of 64 bit processing.
After hours with DELL tech support (what a waste), I just concluded I should make a Dual boot with Vista Home Premium 64 bit.
I did, and Vista 64 does see the current 3gb in the system. I should add, I am going to make it an 8gb system and my memory will arrive from crucial.com tomorrow.
So Bob, to address your comment. I started (2 years ago?) with Windows XP Pro 32 bit. I have a ton of applications (32 bitters) on the C drive now. But I want the extra addressing (AKA speed potential) capability of a 64bit system. In short, that is the reason for the Dual Boot.
I just cannot burn the 32 bit bridge due to the number of 32 bit apps on it, but I can now utilize a 64 bit architecture for PS CS4, (and as I now am reading ID, and IL CS4 flavors)
Hope I cleared things up.
And as always, thanks
Bob

Making a Windows 7 Toshiba laptop a dual boot system (w/ XP)

I am looking to probably get a Toshiba laptop here in the next month. Most likely it will be one that will include WIndows 7. While I have another desktop with Windows 7 installed on it and like it for the most part, there are a few pieces of hardware I have that aren't running correctly right now under W7 due to drivers not being availble for it. Therefore, I made this custom desktop a dual boot system with XP & W7 on it.This way I have XP on it for when I might have to use these pieces of hardware.
I would like to possibly do the same thing for this new Toshiba laptop as well. Have XP on it in case I need it for incompatible hardware & compatibility issues that may arise. Can I easily put XP on a Toshiba laptop with W7 already installed? I would have to create a separate partition to possibly put XP on as this is the way I prefer to have it when making a dual boot system. However, I have several concerns if trying to do this. They include the following:
If I create/add another hard drive partition for XP, will I essentially make the recovery partition/software useless?
When I have made dual boot systems in the past, I usually have to start with the older OS. Then add the newer OS and it will do it automatically. Take care of everything for the dual boot menu. I have experienced problems when going backwards (like this) though. Will that happen as well & I'll then have problems getting back into W7?
If this is the case for both, do most Toshiba Laptops come with recovery software on CDs? This way I can maybe wipe the drive out, install XP and then install W7 (w/ the CDs) in order to make a correct dual boot system. Or does the recovery software/CDs need to be speically ordered directly from Toshiba & that is generally why they just put it on a recovery partition instead?
Solved!
Go to Solution.

Wise of you to investigate in advance.
Your best bet by far nowadays is to get a laptop with hardware virtualization and either the Professional or Ultimate versions of Windows 7 installed. That way, you can use XP Mode.
Windows XP Mode (Toshiba)
Windows XP Mode (Microsoft)
You can even open an XP program directly from a shortcut in Windows 7.
For current models suitable to run XP Mode, I suggest you call ToshibaDirect at 888-520-3926.
-Jerry

Troubles in dual boot system after BIOS update

Hello:
PC: Thinkpad T500
1. I had for one year Linux Fedora 10 and Vista Ultimate working in dual boot with Grub, no problems at all.
Three days ago Lenovo support recommended I update my BIOS from 2.07 to 3.12, as I had some intermitent Sleep problems in Vista. Then my problems started.
2. First, after updating the BIOS from Vista (dowloaded the exe, double clicked it, gone through the whole sequence with no errors), upon the first restart, the screen was black and I couldn't get in BIOS with F1 and the same happened during other power-off/power on sequences.
3. Now, I've discovered that the best I can do is wait for 10 min after restart in order to get a prompt from ThinkVantage, then Grub boots only the Linux system which works OK.
4. I can't get the dual boot message from Grub, and I can't get any Windows DVD to be taken at boot (I've got full backups from both Control Panel and from ThinkAdvantage backup facility) in order to ru Windows repair.
5. I can go during the ThinkAdvantage to BIOS, the new version seems there (not sure if completely operational), but whey can't I see it with F1?
Is the presence of ThinkAdvantage something special in dual-boot systems or wrt to the BIOS install? Should I do something special about it? I just don't know.
Any ideas?

Strange. I don't have a clue, but I have seen posts here that recoverd from strangeness after a BIOS update by unplugging from the AC mains, removing the battery, and then pressing the power button several times. The last time, hold the button for 10 seconds or so.
That is really a total WAG, but maybe worth a try.
Out of curiousity, what do you see when grub finally loads. I take it that it isn't your original boot menu. Do you have grub installed in the MBR, the boot sector of the Linux partition, or both? Is the Linux partition (or Linux boot partition if you have boot + root) the 1st one on the drive, or _after_ the vista partition.
[edit] You didn't ask, but IMNSHO multibooting a modern laptop isn't really the easiest way to run multiple OSs. I run Linux, Solaris, and OS X in VMs under Win 7 on my T400. They run well, and that approach avoids issues like you are having. The Lenovo ThinkVantage boot-time stuff and R&R are rather fragile. Changes in partitioning and MBR configuration can break them. BIOS and other updates, and Windows repairs can break the multi-boot setup.
There are several ways to set up VMs, but VMWare Player is what I use. The latest version is free and quite usable.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

System Status Lock

In my company I am creating project, with reference to WBS / Activity we are creatin Purchase order. We want a temporary status in project by virtue of which we can avoid any further PO against the particular project. How to achieve this ?
I tried to do this with lock status in PS but although I set up Lock for Header level WBS still I can make PO against the project.
Wht is significance of system stastus lock ?
Pl suggest.
Regds

You can either use user status for controlling this, I've mentioned about how this needs to be done is previous post, link below:
Re: Project Purchase order
Else you can set Lock Account Assignment for the WBS, this will stop PO creation against the WBS.
Regards
Sreenivas
Pls close the post if satisfied

[S] Latest Xorg crashes on dual head system when web browser is opened

Due to the long Subject line I abbreviated, the issue is solved but I would still like it if someone could answer my question if someone knows why
After updating Xorg and the Radeon drivers on my dual head system opening any kind of web browser causes Xorg to crash. Any other application: Dolphin, Kopete, Amarok, urxvt open and run just fine with no issues from Xorg (which is baffling me). I have a bunch of single head systems that use ATI video cards that don't have this issue, like the one I am currently on that has Chrome open with four tabs.
I caused a couple of these crashes and grabbed /var/log/Xorg.0.log, can be viewed from here http://sprunge.us/bNZC, as well as grabbed my /etc/X11/xorg.conf.d/10-monitor.conf file, which is here http://sprunge.us/gbNW. SLiMs log file has a little bit more in it as far as errors go, http://sprunge.us/UjVK, mostly how it is trying to load VDPAU which if I remember correctly that is a Nvidia thing is it not? There are also errors how it can't load the RANDR extension. Anyone have any helpful pointers of solving this?
Package details:
xorg-server: 1.12.0-1
xorg-xinit: 1.3.2
xorg-utils: 7.6-8
xorg-server-utils: 7.6-3
xf86-video-ati: 6.14.3-2
ati-dri: 8.0.1-2
udev: 181-2
kernel: 3.2.9-1
Last edited by vendion (2012-03-14 12:10:18)

It seams that my 10-monitor.conf file was causing the issue, why I am not sure... and it would be nice to know what the problem with it was, but after moving that file out of /etc/X11/xorg.conf.d directory and restarting X11 and using xrandr to get my screens setup the way I like them to be X11 no longer crashes when a web browser is opened. I wonder if this will also solve my issue of Awesome randomly crashing after long periods of inactivity...

Setting up a dual boot system with OS 9 and OS 10

I am currently running OS 9.2 on the G4 and want to run OS 10.4 as a dual boot system. Can I go as far as 10.4 with dual boot? Is there any more to it than partitioning the system drive in two and installing the two OS's on the two partitions?

Hi, Matt -
Is there any more to it than partitioning the system drive in two and installing the two OS's on the two partitions?
No.
As Dave Hamilton said, if using OSX's Disk Utility to do the partitioning, be sure you select the option to install OS 9 drivers. If that option is not selected, then OS 9 will not be able to mount the volume(s), nor use one for booting.
Reminder - partitioning a drive requires that it be re-initialized. This will erase everything on the drive, so be sure you have backed up anything you do not want to lose.
And, be sure to select Mac OS Extended as the format for all partitions. That is the only format which can be used by both OS 9 and OSX for booting.
<hr>
Although many folk do partition a drive (or use two separate drives - your DA model is pre-equipped to accept a second internal drive), you do not need to do that in order to install OSX.
OSX should install smoothly onto the same drive where OS 9 is located. There is no conflict between the two - machines which originally came with both OS 9 and OSX pre-installed had both installed on an unpartitioned drive.
However, there are distinct advantages to having OS 9 and OSX on separate volumes or drives -
• Maintenance and/or repair of each OS and its files is easier
• Re-installation of either OS, should that ever be necessary, is easier
• Startup Manager can be used

Homogeneous system copy ECC 6.0 EHP4 dual stack system

Hello ,
I have a requirement of homogeneous system for the below Source system
Source system :
ECC6.0 EHP1 ABAP+java dual stack system with DB2 AIX
Required Target system:
ECC 6.0 EHP1 (same as target system except single stack java not required)
1 .I was trying to use db specific homogeneous system copy method wiht redirected restore script
2. Not possible to get downtime on source system hense it's a production system , then i used target system installaion with homogeneous system copy database specific mehthod
Problem is - it's asking migration export while creating the target system , but i don't have any migration export since i have not exported from source system .
please help us to proceed further.
Thanks in Advance.

2. Not possible to get downtime on source system hense it's a production system , then i used target system installaion with homogeneous system copy database specific mehthod
What did you choose to do in database specific method - DB2 backup/restore ?
//Backup Restore
Homegeneous system copy(database specific method)
Target -
As I understand, you have started IMPORT using SAPinst for target system installation. During IMPORT, what target system installation (only ABAP or what ?) you chose ?
//I took ABAP+JAVA
'Problem is - it's asking migration export while creating the target system , but i don't have any migration export since i have not exported from source system .'
This is because the source system is ABAP+Java, and now during target system installation, then IMPORT procedure is asking for Java Export dump.
Thanks

Error whiel activating cross system object lock

Hi ,
when I am trying to activate the cross system object lock functionality for developement system in tcode /TMWFLOW/CMSCONF from our solman system , it showing the following error
'Error RFC destination SM_SMDCLNT000_TRUSTED: You are not authorized to logon to the target system (error code 1).
Message no. /TMWFLOW/TRACK_N106'
In the above RFC connection the 'Current user' is provided.
Can anyone please let me know what I am missing in this?

Hi Farzan,
I dont have autorization in Client 000 of SMD system thats why its giving authorization error but when I am trying to activate the object locking for SMD client 321 why the system is trying to logging into the SMD : 000 can we somewhere modify the RFC conection which needs to be used.
Regards,
Amar Kamat

How to change Java UME to point to LADP in dual Stack System.

Hi,
We are in the process of CRM upgrade from 5.x to 7.0. Our 5.x system is dual stack system and Java UME authentication is set to dataSourceConfiguration_r3_roles_db.xml
Right now CRM users login to Enterprise Portal using ADS authentication and access CRM using Single Sign On.
But in 7.0 they want to use JAVA stack in CRM directly using ADS.
According to this note 718383, we can't change UME to LDAP if it's set to dataSourceConfiguration_r3_roles_db.xml.
Please suggest how we can change UME to ADS during CRM upgrade to 7.0.
Thanks for your help!!
Kiran

> According to this note 718383, we can't change UME to LDAP if it's set to dataSourceConfiguration_r3_roles_db.xml.
Correct. Otherwise you will loose the 'connection' between the ABAP user and the roles.
> Please suggest how we can change UME to ADS during CRM upgrade to 7.0.
You can't. A dual stack instance requires the Java user store being in ABAP.
I would recommend anyway separating the two instances and making two out of them and no more use double stack systems. This will make changes easier and also does not force you to keep them both in sync (supportpackages).
Markus

Dual VXI System Sometimes Locks Up

Similar Messages

Maybe you are looking for