EEM detector SNMP OID does not work

i want to use EEM to detector policy-map class traffic rate, if class traffic is more than a number, trigger syslog message.
below is my EEm script on ASR1002 ( asr1000rp1-adventerprisek9.02.04.02.122-33.XND2.bin)
event manager applet Rate-limit
event snmp oid ".1.3.6.1.4.1.9.9.166.1.15.1.1.10.50.196608" get-type exact entry-op gt entry-val "100" poll-interval 10
action 1.0 syslog msg "policy Rate-limit"
but i did not see anything showing on syslog. from debug, i got below error msg :
Jun 1 02:21:49.160 GMT: fh_fd_snmp_process_async
Jun 1 02:21:49.160 GMT: fh_fd_snmp_process_poll_timer: re=0x3D144824, timer_type=POLL
Jun 1 02:21:49.160 GMT: fh_fd_snmp_process_poll_timer: OID unavailable, value check skipped
Jun 1 02:21:49.160 GMT: fh_fd_snmp_start_poll_timer: start_t=10000
but i could get number from snmpwalk command :
xchen-mac:~ xchen$ snmpwalk -v 2c -c <string> -m ALL stde1002a .1.3.6.1.4.1.9.9.166.1.15.1.1.10.50.196608
SNMPv2-SMI::enterprises.9.9.166.1.15.1.1.10.50.196608 = Counter64: 112938
please help me where is wrong ?

Duplicate post.
Go here: https://supportforums.cisco.com/discussion/12219976/eem-detect-snmp-event-not-working

Similar Messages

The cisco snmp oids do not work, I can't get cpu or memory data.

Hello. I want to monitor the cpu and memory usages on my cisco devices using snmp. I found the snmp oids related to cpu in the following page :
http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a94.shtml
I just copy the table here:
But the oids in the table do not work on my devices. For example, I have a cisco 3550 switch with the ip 192.168.1.211, version 12.2(25)when I want to get the informations about the oids up in the table, I got these results:
It shows that the oids cisco given up in the table are not existed in my 3550 switch's MIB. More weird is that when i add a number "1" to
the end of the oid cisco given, I can get some meaningless data for some unkonwn item names like "entreprises.x.x".
For most mib items, the snmp oids work well on my switch. For example, the following graph shows the interface out rate of the swtich:
I think the essence is when I executed the following command:
in all the output results, there's not any item relevant with "cpu" or "memory", but most other items are ok, such as interfaces, as shown below:
IF-MIB::ifDescr.47 = STRING: FastEthernet0/39
IF-MIB::ifDescr.48 = STRING: FastEthernet0/40
IF-MIB::ifDescr.49 = STRING: GigabitEthernet0/1
IF-MIB::ifDescr.50 = STRING: GigabitEthernet0/2
IF-MIB::ifDescr.51 = STRING: Null0
IF-MIB::ifDescr.52 = STRING: Vlan1
IF-MIB::ifType.1 = INTEGER: ethernetCsmacd(6)
IF-MIB::ifType.2 = INTEGER: ethernetCsmacd(6)
IF-MIB::ifType.3 = INTEGER: ethernetCsmacd(6)
IF-MIB::ifType.4 = INTEGER: ethernetCsmacd(6)
IF-MIB::ifType.5 = INTEGER: ethernetCsmacd(6)
So why the cisco given oids won't work on my cisco switch, and how can I get the datas I want? Anyone has some advices? Thanks in advance!
In case the pictures I inserted missing, I attach my problem in the doc.

Have you looked at this previous discussion:
Can't Activate FaceTime

SQLDEVELOPER 2.5 and above on WinXP/Win7 does not work with OID auth ?

Hi,
I have SQLDEVELOPER 1.5 on my WinXP which works fine with database local users as well as global users(OID) authentication. But with SQLDEVELOPER 2.5 and above it throws below error with OID authentication.. local user authentication is however fine.
Status:Failure-test failed:unsupported verified type
Any idea why Sqldeveloer 2.5 and above does not work with OID auth?
Thanks for help
Sivaji

It might be to do with the oracle client version or the JDBC version. (for example v3 needs the 11i jdbc drivers and associated dlls for oci connections.

SNMP does not work

The SNMP on my new TC does not work. I have enabled it disabled it at least 50 times. Rebooted the TC. Unplugged the TC. You name it. It worked once and only once for about 4 hours.
Any suggestions?

Assuming you can ping both firewalls, the problem is that the firewall pair shares the same config and therefore, the same SNMPv3 engineID. Some NMSs (e.g. WhatsUp Gold) do not support this and therefore only 1 firewall in the pair can be queried.
Doesn't look like this has been fixed yet:
Bug info: CSCtl88556 - ASA5520 failover pair has duplicate snmp v3 engine id

My Time Capsule does not work with existing WiFi

Following a question solved on March 24 by LaPastenague, but gone bad again.
Apple AirPort Time Capsule
I felt the need for a physical backup of my data, as I would not completely trust the different clouds. I use, and have used Dropbox for 4-5 years and are very satisfied with that, but I am still not sure if or when a political lunatic will shut off the internet.
I purchased the Apple AP Time Capsule 2T, because all my other stuff are Apple, and that it's wireless. My old backup is Maxtor 300 GB.
Since we stay 2-3 weeks on two locations, one in Norway and one in Sweden (two different countries) we must use Mobile Broadband 4G, cables or fibre connections are useless for us, and we don't have it up to the houses. I have one mini router for each country, we bring with us iPhones, iPads, iMac, Apple TV, APExpress. When we pass the boarder I change the mini router, and the system continues working perfect on the WiFi, except the APExpress that needs to be reconfigured, but then it works.
The APTC was difficult to make working as it would not accept to be in an existing network, but with good help from the Apple Community, LaPastenague, with forcing the TC connect to the APE with Ethernet cable in bridge mode, ref "My Time Capsule does not work with existing WiFi" from March 24, the problem was solved and all gadgets worked together in a perfect harmony, until we changed location.
Now, as I have my second WiFi network, and the APExspress is reconfigured, it's like the TC thinks, I am the base boss here, I am not taking orders from APE one more time, and it simply does not work, not only that, it fluctuates all the time.
I have a slight feeling that the two WiFi bands are making the trouble as during the configuration of the TC sometime the last figure 6 and 7 pops up, and that has something two do with the two different 2,4 and 5 GHZ bands
So, I am curious if you have any idea ?
I am thinking of returning the TC if I don't make it work now, but how do I delete all the data that's on it?

I can deal with the last question first and easily.
I am thinking of returning the TC if I don't make it work now, but how do I delete all the data that's on it?
Open the airport utility .. go to the disk tab and select erase.
When you select erase you will get mulitiple options.
Quick removes the file table but does not delete the files,, it takes 2min or less.
A Zero out data is the secure way,, by writing 0 ie low level drive format.
It can take several hours..
7 pass will take a week.. not recommended..
35 pass erase is ridiculous.. it would take a month.. put an ax through the TC. It is quick and better.
Now, as I have my second WiFi network, and the APExspress is reconfigured, it's like the TC thinks, I am the base boss here, I am not taking orders from APE one more time, and it simply does not work, not only that, it fluctuates all the time.
The fact that it did work and has now failed might point to faulty unit.
The only way to tell is reset it properly to factory and start over.
Universal Factory Reset.. any model TC or AE.
Unplug your TC/AE from power or turn off at the power point.
Hold in reset. and power the TC/AE back on.. all without releasing reset and keep holding in for about 10sec. (this is often difficult without a 2nd person or a 3rd arm).
Release it when the status light flashes rapidly. If it doesn’t flash rapidly you have missed it and try again.
Note..
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations of the router.
No files are deleted on the hard disk in a TC.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
Generally having multiple wireless AP should not cause problems.. but it is better to set channels manually.. so it doesn't go beserk rotating channels.
Remember to keep all names short, no spaces and pure alphanumeric.
Sadly though the Apple routers have no logging now and no SNMP and almost nothing to help diagnose a problem, so if it continues .. take it back to apple.. they have given you no other method of fixing it.

After upgrading to mavericks my epson scanner v 600 does not work

After upgrading to Mavericks my scanner V600 epson does not work, I keep getting a message to re-install the software, but even then is does not work

I'm having the same issue. The scanning software doesn't launch, the scanner appears in system preferences after a few unplugs and plugins, and software update doesn't give me the recommended ICA update.
Also the Epson scan utilities aren't updated either and will be "released soon" according to here:
http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?BV_UseBVCookie=yes&oid= 139863&prodoid=63084673&infoType=Downloads&detected=yes&platform=OSF_M_X9
They recommend to use image capture (which is a joke) in the mean time or you could buy vuescan but thats not much better for some things.

MAC Authentication does not work

My MAC Authentication does not work.
I have a ACS 3.0 server set. the MAC address is set in the user name field and in the password field.
I can ping the ACS, I can ping my AP, I can ping my client.
I don't want WEP and I don't want LEAP just MAC. So I set my authentication to "Open with MAC" My client has WEP set to NO WEP and authentication to OPEN
I have the latest drivers for both AP and my 350 Client.
I see that the client is associating and disassociating back and forth non stop. My AP log is full with the following message:
Station 0009.7c9f.xxxx Authentication failed
this is my config:
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname GOM_1200IOS
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
server 10.1.2.197 auth-port 1812 acct-port 1812
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa group server radius wlccp_rad_infra
aaa group server radius wlccp_rad_eap
aaa group server radius wlccp_rad_leap
aaa group server radius wlccp_rad_mac
aaa group server radius wlccp_rad_any
aaa group server radius wlccp_rad_acct
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authentication login wlccp_infra group wlccp_rad_infra
aaa authentication login wlccp_eap_client group wlccp_rad_eap
aaa authentication login wlccp_leap_client group wlccp_rad_leap
aaa authentication login wlccp_mac_client group wlccp_rad_mac
aaa authentication login wlccp_any_client group wlccp_rad_any
aaa authorization exec default local
aaa authorization ipmobile default group rad_pmip
aaa accounting network acct_methods start-stop group rad_acct
aaa accounting network wlccp_acct_client start-stop group wlccp_rad_acct
aaa session-id common
enable secret xxxxxx
username Cisco password xxxx
ip subnet-zero
iapp standby timeout 5
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption key 1 size 40bit 7 9DF1C10BF11A transmit-key
ssid GOM_1230
authentication open mac-address mac_methods
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0
rts threshold 2312
channel 2462
station-role root
no cdp enable
dot1x reauth-period server
dot1x client-timeout 600
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no cdp enable
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 172.16.43.45 255.255.240.0
no ip route-cache
ip default-gateway 172.16.47.254
ip http server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag/ivory/1100
ip radius source-interface BVI1
access-list 700 permit 000a.b74c.e8c9 0000.0000.0000
access-list 700 permit 0009.7c9f.d6e0 0000.0000.0000
access-list 700 permit 0006.25b1.2f79 0000.0000.0000
access-list 700 permit 000a.b78b.2d19 0000.0000.0000
access-list 700 permit 000b.5f6e.77c8 0000.0000.0000
access-list 700 deny 0000.0000.0000 ffff.ffff.ffff
access-list 701 deny 000b.5f6e.77c8 0000.0000.0000
access-list 701 permit 0000.0000.0000 ffff.ffff.ffff
no cdp run
snmp-server community GOM_AP1230 RO
snmp-server enable traps tty
radius-server local
group AP1230
user brazil nthash 7 1249523544595F517972017912677A3055325A25770B08770D5C5B4E4478087605 group AP1230
radius-server host 10.1.2.197 auth-port 1812 acct-port 1812 key 7 00233C2B
radius-server retransmit 3
radius-server attribute 32 include-in-access-req format %h
radius-server authorization permit missing Service-Type
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 5 15
end
What is wrong?
Thanks very much for your help.

I figured out what was wrong so thank you for stopping by.
I will publish the config for other people to see.
Regards,

Directory Naming with OFM 11g - Identity Management Does Not Work.

I tried to find document about how to setup/implement Directory Naming with Oracle Fusion Middleware 11g- Identity Management, but without luck. We implement Directory Naming with IM 10.1.4.3 on Linux that is 32-bit only and doesn't coexist very well with OEM GC (64-bit). So we are very eager to try 64-bit of IM 11.1.1. Any information is highly appreciated. Thanks huge.
Edited by: bhqu888 on Aug 16, 2009 6:51 PM
Edited by: bhqu888 on Aug 16, 2009 6:56 PM

I installed OFM IM 11.1.1 on RHEL 4.8 (x64) successfully and OID is up and running. Using Net Manager in the $ORACLE_HOME/bin dir I can upload TNS to OID. But Directory Naming does not work. Dbs client could not log into any dbs server through this 11g OID. Our 10.1.4 OID works fine.
Edited by: bhqu888 on Aug 16, 2009 6:51 PM
Edited by: bhqu888 on Aug 16, 2009 6:58 PM

Installed Premiere Pro CS4 but video display does not work?

I just got my copy of CS$. After installing Premiere I found two things that seem very wrong:
1) video display does not work, not even the little playback viewer next to improted film clips located on the project / sequence window. Audio works fine.
2) the UI is way too slow for my big beefy system.
My pc is a dual boot Vista-32 and XP system with 4GB of memory installed and nvidia geforce 280 graphics board with plenty of GPU power. The CS4 is installed on the Vista-32 partition. My windows XP partition on the same PC with Premiere CS2 works great and real fast.
Any ideas how to solve this CS4 install issue?
Ron

I would like to thank Dan, Hunt, and Haram:
The problem is now very clear to me. The problem only shows up with video footage imported into PP CS4 encoded with "MS Video 1" codec. So this seems to be a bug. The codec is very clearly called out and supported within various menues but video with this codec just will not play in any monitor or preview window. In addition the entire product looks horrible with respect to performance while PP CS4 trys its best to play the video. Audio will start playing after about 30 seconds. And once in awhile part of video shows up at the wrong magnification before blanking out again.
My suggestion to the Adobe team: fix the bug and add some sample footage to the next release so new installations can test their systems with known footage.
My PC is brand new with the following "beefy" components:
Motherboard
nForce 790i SLI FTW
Features:
3x PCI Express x16 graphics support
PCI Express 2.0
NVIDIA SLI-Ready (requires multiple NVIDIA GeForce GPUs)
DDR3-2000 SLI-Ready memory w/ ERP 2.0 (requires select third party system memory)
Overclocking tools
NVIDIA MediaSheild w/ 9 SATA 3 Gb/sec ports
ESA Certified
NVIDIA DualNet and FirstPacket Ethernet technology
Registered
CPU: Intel Core 2 Quad Q9550
S-Spec: SLAWQ
Ver: E36105-001
Product Code: BX80569Q9550
Made in Malaysia
Pack Date: 09/04/08
Features:
Freq.: 2.83 GHz
L2 Cache: 12 MHz Cache
FSB: 1333 MHz (MT/s)
Core: 45nm
Code named: Yorkfield
Power:95W
Socket: LGA775
Cooling: Liquid Cooled
NVIDIAGeForce GTX 280 SC graphics card
Features:
1 GB of onboard memory
Full Microsoft DirectX 10
NVIDIA 2-way and 3-way SLI Ready
NVIDIA PureVideo HD technology
NVIDIA PhysX Ready
NVIDI CUDA technology
PCI Express 2.0 support
Dual-link HDCP
OpenGL 2.1 Capaple
Output: DVI (2 dual-link), HDTV
Western Digital
2 WD VelociRaptor 300 GB SATA Hard Drives configured as Raid 0
Features:
10,000 RPM, 3 Gb/sec transfer rate
RAM Memory , Corsair 4 GB (2 x 2 GB) 1333 MHz DDR3
p/n: TW3X4G1333C9DHX G
product: CM3X2048-1333C9DHX
Features:
XMS3 DHX Dual-Path 'heat xchange'
2048 x 2 MB
1333 MHz
Latency 9-9-9-24-2T
1.6V ver3.2

A2109 tablet autorotate does not work

The autorotation on my recently purchased tablet A2109 does not work. I look in settings and the auto rotate field is not highlighted, I therefore cannot choose to turn it on.The tablet has the Android jellybean OS and I did update it but to no avail. Can anyone help?
Thanks
Solved!
Go to Solution.

Dear tdsouza
Welcome in lenovo forums
just a clarification , do you mean option Rotate is dimmed in setting
Please let me know
Thanks
Alaa
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

For what reason on my tablet with OS Android 4.1 does not work flash on the sites?

Hi! I recently bought a Google Nexus 7 tablet with Android 4.1 operating system and on my tablet does not work flash sites. Why adobe does not release a new version of flash for android 4.1? Why it was necessary to buy a company Macromedia, if adobe does not want to develop web technology? I think against Adobe can sue for violation of antitrust

I found this for example:
http://www.slashgear.com/adobe-no-jelly-bean-flash-flash-player-pulled-altogether-august-1 5-29236404/

My flash flayer does not work on my Windows 8 Surface Tablet, it also won't let me see if i already

My flash flayer does not work on my Windows 8 Surface Tablet, it also won't let me see if i already have it installed...

1.      Are you getting any error message?
2.      Which browser are you using?
3.      Were there any recent changes made on the computer prior to the issue?

My flash player does not work on my tablet.

My flash player does not work on my tablet

Your tablet uses Android OS.
There is no more Flash Player for Android and there won't be another. Android is no longer compatible with Flash Player. Playing Flash content is very processor consumptive and it drains your battery, also shortening the life of it. Android (Google) recommends using either "Dolphin" or "Puffin" as your browser if you need to view Flash content with a mobile device running Android. They're both free in the GooglePlay store. These browsers use "server side" rendering to reduce the load on your device.

Dynamic image does not work in the template builder plug-in (Apex-BI Intgr)

Hi all, I posted this problem in the BI Publisher topic but nobody responded maybe this is because mods thought this is an Apex-BI integration issue.
If I'm in the wrong place, please do warn me.
The documentation says:
Direct Insertion
Insert the jpg, gif, or png image directly in your template.
...This works obviously
URL Reference
1. Insert a dummy image in your template.
2. In Microsoft Word's Format Picture dialog box select the Web tab. Enter the following syntax in the Alternative text region to reference the image URL:
url:{'http://image location'}
For example, enter: url:{'http://www.oracle.com/images/ora_log.gif'}
...This works too when I hardcode an url as url:{'http://www.google.com.tr/images/firefox/mobiledownload.png'}
Element Reference from XML File
1. Insert a dummy image in your template.
2. In Microsoft Word's Format Picture dialog box select the Web tab. Enter the following syntax in the Alternative text region to reference the image URL:
url:{IMAGE_LOCATION}
where IMAGE_LOCATION is an element from your XML file that holds the full URL to the image.
...This, however, does not work.
I use Apex' report query tool and My query is like
select 'http://www.google.com.tr/images/firefox/mobiledownload.png' IMAGE_LOCATION from ... (a single result set for my template)
the xml data is generated with an IMAGE_LOCATION tag. I load it to word template plug-in. The Url successfully displays in the report if I make it a plain-simple field.
But when it's in the image format->web->alt text as url:{IMAGE_LOCATION} no image displayed.
I need to keep this design procedure simple so a simple word user could design a report via using just template builder plug-in. I don't wish to explore the xsl-fo area...yet.
Could you tell me why I can't get this url:{IMAGE_LOCATION} to work?
Regards
PS: My BI version: 10.1.3.4.1

Hi Oeren,
your steps seem basically to be correct. I have a tutorial how to do this here (in german)
http://www.oracle.com/webfolder/technetwork/de/community/apex/tipps/pdf-dyn-images/index.html
when you see the URL corrently as long as you have it as a plain text field, the XML tag and the
referencing seem to be OK.
Here are two thought - the issue might be one of these ...
How did you insert the dummy image into the word document - did you do it via "insert" or
via "link to file". "Link to File" does not work - you must choose the simple "insert".
Another one: Does your BI Server have a connection to the internet - is the proxy server correctly set ..?
Does this help ..?
Regards
-Carsten
Cloud Computing mit APEX umsetzen. Jetzt!
http://tinyurl.com/apexcloudde
SQL und PL/SQL: Tipps, Tricks & Best Practice
http://sql-plsql-de.blogspot.com

I have an event in my calendar that was sent by someone who does not work for the company anymore and I am reminded 2 times a week. How can I remove it?

I have an event in my calendar that was sent by someone that does not work for the company anymore and I am reminded 2 times a week. How do I delete it?

Tap on the event to open the event. Click the 'Edit' button in the event bubble, then press the 'Delete Event' button at the bottom of the Edit pop-up. It's a little different for events that come through Microsoft Exchange, you tap the event to bring up bubble and click the 'Details' button, and then press 'Decline' to remove the event.

EEM detector SNMP OID does not work

Similar Messages

Maybe you are looking for