EEM variable for show command output and create a filename

I'm configuring EEM applet, example CPU High event. When it triggers the event, action is "show tech | redirect tftp://x.x.x.x/showtechoutput". The EEM event is working fine and triggered the show tech output into the tftp server. My question is, i'd like to add maybe date/time in the filename so it will not overwrite the file everytime there is a triggered event.
The EEM event variable i'm seeing in doc is "_event_pub_sec" but it won't work when i add after or before the filename. any idea?
thanks in advance ...

Adding $_event_pub_sec to the end of the filename should work:
action 1.0 "show tech | redirect tftp://x.x.x.x/showtech.$_event_pub_sec"
That said, TFTP is very particular about how files can be created. Typically, a TFTP server will require the file to exist before a remote host can copy to it. If the filename changes each second, this will not work. Using a protocol like FTP or SCP may work better.

Similar Messages

Sending 'show' command outputs to console/terminal using EEM

Hi Everyone,
I'm new to EEM and was wondering if it would be possible to send 'show' commands (like 'show interface' or 'show crypto ipsec sa') to the terminal/console session after every, let's say, 10 minutes using watchdog timer. I know how to send it to the flash but would like to know if something of this sort is possible.
Any suggestions would be really appreciated!
Regards,
Nikhil

Hi Nithakur,
you can try the "action puts" from EEM
event manager applet SHOWI
event timer watchdog time 600
action 1.0 cli command "enable"
action 2.0 cli command "show int X/Y"
action 3.0 puts "$_cli_result"
for this to work, you would need to have "logging monitor informational" in your run and "terminal monitor" activated. The other option is to use IOS send command
event manager applet SHOWI2
event timer watchdog time 600
action 1.0 cli command "enable"
action 2.0 cli command "show int XY"
action 3.0 set A "$_cli_result"
action 4.0 cli command "send *" pattern "C:"
action 5.0 cli command "$A\032" pattern "confirm"
action 6.0 cli command "yes"
Note that the \032 is an equivalent for CTRL+Z (^Z) so after you configure it, you will see this line as
action 5.0 cli command "$A^Z" pattern "confirm"
in your ruiining config.
Regards,
Alex

Sun Studio 11 do not parse make output and create link to file?

Hi,
Running Sun Studio 11 and can only get file links in the output window when I run a make command that uses CC -g (debug option). We have integrated other tools into our make system (flexlint, cppUnit..) and even though we make sure that the syntax is exactly the same as the compiler output and matches regular expression under tools->options->building->make settings->error expression, it doesn't work. Why do you have to debug compile to get sun studio to create a file link in the output window? Doesn't sun studio just parse the text from the make command?
example of flexlint output for which no link is created:
"/vobs/project/oss/fm/fm4/fm-fmalib/fmbal/fmaaulib/src/FMA_List.cc", line 440: Error 84: sizeof object is zero or object is undefined'�
example of make debug output for which we do get a link:
"/vobs/project/oss/fm/fm4/fm-fmalib/fmbal/SunOS5.10/inc/FMA_alarm_record.hh", line 1310: Warning (Anachronism):Info "static" is not allowed and is being ignored.
Regards,
Ola

I'd second Maxim's suggestion: try NetBeans 5.5 with C/C++ Development Pack. The official release of NetBeans C/C++ Development Pack 5.5 has happened a few days ago. You can download it from
http://www.netbeans.info/downloads/all.php?b_id=2284
Some of the changes between the beta3 build and FCS are:
* Significant performance improvements in the code parser resulting in faster results in the Class View and Code Completion
* Programs now run in an external terminal (system dependent) by default. This allows better input control
* Significant performance improvement in the debugging module
* Significant functionality improvement in the debugging module
* New project type "C/C++ Project From Existing Code" which simplifies creating a project from existing code
* Macro support in code completion
* Hyperlink navigation for macro usages and #include directives
* Reformat code
* Code folding
* Code completion
All these features will appear in next Sun Studio release, so you can
consider NetBeans C/C++ Development Pack 5.5 as a preview of new
Sun Studio IDE.

How can I use a variable for an interface log and error fle

I want to use a variable for the interface's log and error file so that when I migrate from Dev to QA to Prod I don't have to do a lot of editing.
Specifically on the "flow" tab for the "target", I want a variable to be the first part of the path for the log (\\sundev1\fnd1-hypd1) and join this with the rest (\update\log\logfile.log) within the LOG_FILE_NAME field.
Thank you!

Hi,
It is quite simple....
just use the <%=odiRef.getSchemaName("D")%> before the file name and configure both path in the topology linked to each context.

Table name for Customer Account Group and created by Data

Dear Gurus,
Kindly le t me know the table name having a list of Customer a/c groups and created by data. if there is no such table thn pls let me know the alternatives for fetching the same data.
Wishes
Abhishek

hI
Go to Se11 and give table name KNA1 and go to display
you can able to see the Customer AccountGroup field :KTOKD
Thanks
Vasu

Table Name for Partner Determination Procedure and created by data

Dear Gurus,
kindly let me know the table name for a list of "Partner Determination Procedure" and "created by" data under a client.
if there is no such table for this, kindly let me know how can i fetch these details.
Wishes,
Abhishek

Hi Abhishek,
You can get your required information by combining these 2 table by using SQVI
TPAER where it gives PartnDet.Proc and Part.funct.
TPAR where it gives Part.funct inforamtion.
By using these tables i.e. by using Common field Part.funct. - PARVW
Regards
Durga Sana

Has the options for custom command buttons and scripts been removed from speedgrade?

I run alot of framecyclerDI machines and am looking to upgrade them but i cant seem to find any method of adding command bars and buttons like you could in the iridas versions of speedgrade i also cant see a way of executing any external scripts which for me is a big issue as i have a hell of alot of pipeline scripts that the artist could execute.... any ideas or have i just missed somthing ?.......(would love it if they added a python sdk)

Hi Dennis,
Thanks for replying,
Its actually more the other way getting speed grade to control outher things.
i.e
take the in and out points and send the track to a dcp creator
rendering and sending anotated frames directly into my databases notes system
taking the shotname and seeing if theres is a new version avaliable and pull it from the server to the local machine drive/cache
Theres a load more..but you get the idea .. using the buttons to execute these commands in the interface made these functions editor friendly...
I can get round some of the issues by reading from the autosave.ircp and setting up a PYQT GUI but that seems like a bit of a hack.
I understand the reasons to keep the UI uniform (editors dont like it when you move buttons) but Im suprised these options got removed as intergrating software into pre-existing pipelines would seem to be a selling point for any software..
Are there any plans in the roadmap for speedgrade that would help me in the future?
S.P.F

How to Install IHAT10.1.3 for both command line and web

Hi,
I am trying to install iHAT10.1.3 onto my linux x86 machine. However the instruction I am following in the README is not working for me. Can anyone give me an example of how to install and view iHat for command line and the web
Cheers
Jat

What stage during the instructions are you encountering problems. Can you provide the error details if any?
The 10.1.3 iHAT is only Web based using Flash at the client for displaying compopnents. Unlike the old iHAT, there is not thick client provided to invoke from the command line.
null

"Command I" shortcut in Preview - designated for show/hide toolbar AND show inspector?

In the Mac Preview App, I tried using the the 'command I' shortcut to show/ hide the toolbar, but it brings up the inspector instead. Is the shortcut is designated for both these functions?

Actually the Toolbar hide/show isn't "cmd i" it's "cmd shift |"
That little key on the far right edge between the "delete" and "return" keys. The same key that has "\" as the main function.
KOT

ACE Sticky Connections, Show Conn Output and Show serverfarm

Hi Community,
I'm deploying a Cisco ACE module and I have some questions about sticky connections and about the output of the show conn command and show serverfarm command.
I have the follwoing configuration:
rserver host srv_1 ip address 10.4.11.14 inservicerserver host srv_2 ip address 10.4.11.18 inserviceserverfarm host farm_144 rserver srv_1 144    weight 1    inservice rserver srv_2 144    weight 3    inservice
sticky ip-netmask 255.255.255.255 address source st_host144
timeout 10080
serverfarm farm_144
class-map match-all vip_144
2 match virtual-address 10.4.11.208 tcp eq 143
policy-map type loadbalance first-match lb_144
class class-default
policy-map multi-match policy_vip_webcache
class vip_webcache_144
    loadbalance vip inservice
    loadbalance policy lb_144
    loadbalance vip icmp-reply active
    nat dynamic 411 vlan 411
We can assume that service policy was applied at the interface vlan. So, let's go to the questions:
1- If sticky is enabled the output command "show conn" should show just one entry by ip address?
The real output is:
DC01-ACE-01-PRIMARY-SW1/context_servidores# show conn | inc :143333046     1 in TCP   411 10.2.158.87:3616      10.4.11.208:143       ESTAB 286390     3 in TCP   411 10.2.158.87:3562      10.4.11.208:143       ESTAB310233     1 in TCP   411 10.1.5.87:3424        10.4.11.208:143       ESTAB
Look that the ip address 10.2.158.87 is shown 2 times. In same times, the same ip address is shown 4 times to the same VIP and the same port. Is it a normal behavior?
2- According to the configuration, the srv_2 has weight 3 and srv_1 has weigth 1, but the output of show serverfarm show somethin strange:
DC01-ACE-01-PRIMARY-SW1/context_servidores# show serverfarm farm_144 serverfarm     : farm_144, type: HOST total rservers : 2 state          : ACTIVE DWS state      : DISABLED ---------------------------------                                                ----------connections-----------       real                  weight state        current    total      failures    ---+---------------------+------+------------+----------+----------+---------   rserver: srv_1       10.4.11.14:144        1   OPERATIONAL     11         386        0   rserver: srv_2       10.4.11.18:144        3   OPERATIONAL     35         66         0
We can see that the weight is working good, but the total of connections is higher at srv_1 than srv_2. Why?
Somebody can help me to understand better this problem of if its a normal behavior?
Thanks in advance!!

Hi Gaurav,
About question 1, I got some informations too. It's perfectly normal the client open 2 or more connections at the same time. The client's application is the responsable. We removed the ACE and put the client directly to the server and the result of the total connections opened was the same.
About question 2, I made some "clears" on the serverfarm, the sticky database and after that, the numbers were more real.
DC01-ACE-02-SECONDARY-SW1/context_servidores# sh serverfarm farm_webcache_144
serverfarm     : farm_webcache_144, type: HOST
total rservers : 2
state          : ACTIVE
DWS state      : DISABLED
                                                ----------connections-----------
       real                  weight state        current    total      failures
   ---+---------------------+------+------------+----------+----------+---------
   rserver: srv_webcache_1
       10.4.11.14:144        1   OPERATIONAL     1025       15499      4436
   rserver: srv_webcache_2
       10.4.11.18:144        2   OPERATIONAL     1794       33471      471
DC01-ACE-02-SECONDARY-SW1/context_servidores#
Anyway thank you very much for your feedback.
Plínio Monteiro

Custom Infotype : Only for Disply Mode Change and Create Should be disable

Dear Experts,
I Created a custom infotype in PM01 for Exit process , my client requirement is this infotype only shows the details .
Could you please tell me how to disable the Create and change button in PA30 Screen ?
Regards,
Sivakumar.A

hi siva
In PM01 itself you have option module pool, select that option go to screen program.
there select field->dbl clk-> screen attributes pop up will come.
there you have to change the input/output option
Regards
Deva

EEM TCL for interface commands

I am working on a script that will make interface changes. I am trying to do the following:
1) save the output from the following command: #show cdp nei detail | i Interface
2) this will most likely give a list of interfaces some of which will be repeated. If the interface is listed more than once then i would like to remove the
    repeated interface. (note i am not concerned about the outgoing interface)
3)using the above information i would then like to make configuration to the interfaces with the following commands
     #config t
     #interface $intf
     #no mls qos vlan-based
     #mls qos trust dscp
i have started this script (please see attached file) and would really appreciate some assistance especially with how to eliminate multiple instances of the same interface.
thanks!!

I am having issues running scripts on my 3750x. One of the few commands i am getting to work is the
router(tcl)#puts "testing this command"
most all other commands are not working for example: ios_config, set
I am attaching a file with more details. Any help would be greatly appreciated!

Show policy-map interface | Question about QOS show command output

I hope this is the correct place for this question. If not, please let me know.
When I issue the show policy-map interface command (in this case on a 3845) there is some output I don't understand. I have included some output below and formatted the lines I am confused about as "computer code" which show up as red on my screen. A list of the individual lines i'm confused about is below, followed by those liens in the context of the show policy-map command's output.
Any help with this will be greatly appreciated. Thanks in advance.
5 minute offered rate 46000 bps, drop rate 0 bps
5 minute rate 10000 bps
bandwidth remaining 50% (768 kbps)
show policy-map interface
--- previous output omitted ---
GigabitEthernet0/0
Service-policy input: QoS_IN
class-map: Silver (match-any)
      164691299 packets, 23570752398 bytes
      5 minute offered rate 46000 bps, drop rate 0 bps
      Match: access-group name MAINFRAME
        4371992 packets, 2311242335 bytes
        5 minute rate 0 bps
      Match: access-group name KRONOS
        13334297 packets, 3051409140 bytes
        5 minute rate 5000 bps
      Match: access-group name EMAIL
        97652823 packets, 10323856470 bytes
        5 minute rate 10000 bps
      Match: access-group name VOIP-CONTROL
        20782858 packets, 1481676784 bytes
        5 minute rate 0 bps
      Match: access-group name LOGIXWEB
        0 packets, 0 bytes
        5 minute rate 0 bps
      Match: access-group name GRINDLOG
        0 packets, 0 bytes
        5 minute rate 0 bps
      Match: access-group name CITRIX
        46895 packets, 14669179 bytes
        5 minute rate 0 bps
      Match: access-group name CORP_WEB
        28502414 packets, 6387897396 bytes
        5 minute rate 4000 bps
      QoS Set
        dscp af31
          Packets marked 164691269
show policy-map interface s0/0/0:0
Serial0/0/0:0
Service-policy output: QoS_OUT
--- previous output omitted ---
    Class-map: Silver (match-any)
      86590227 packets, 12051546524 bytes
      5 minute offered rate 3000 bps, drop rate 0 bps
      Match: access-group name MAINFRAME
        7641084 packets, 2701232492 bytes
        5 minute rate 0 bps
      Match: access-group name KRONOS
        6975052 packets, 1555404656 bytes
        5 minute rate 0 bps
      Match: access-group name EMAIL
        58438150 packets, 5433636586 bytes
        5 minute rate 3000 bps
      Match: access-group name VOIP-CONTROL
        355083 packets, 41252455 bytes
        5 minute rate 0 bps
      Match: access-group name LOGIXWEB
        0 packets, 0 bytes
        5 minute rate 0 bps
      Match: access-group name GRINDLOG
        0 packets, 0 bytes
        5 minute rate 0 bps
      Match: access-group name CITRIX
        19 packets, 4967 bytes
        5 minute rate 0 bps
      Match: access-group name CORP_WEB
        13180836 packets, 2320015236 bytes
        5 minute rate 0 bps
      Queueing
      queue limit 64 packets
      (queue depth/total drops/no-buffer drops) 0/18156/0
      (pkts output/bytes output) 86421413/12004278837
      bandwidth remaining 50% (768 kbps)

this is my configuration
DGMGRL> show configuration
Configuration
Name: matrix
Enabled: YES
Protection Mode: MaxPerformance
Databases:
stdby1 - Primary database
stdby2 - Physical standby database
stdby3 - Physical standby database
Fast-Start Failover: DISABLED
Current status for "matrix":
SUCCESS
--- this is my first successful switchover -----
DGMGRL> switchover to stdby2
Performing switchover NOW, please wait...
New primary database "stdby2" is opening...
Operation requires shutdown of instance "stdby1" on database "stdby1"
Shutting down instance "stdby1"...
ORA-01109: database not open
Database dismounted.
ORACLE instance shut down.
Operation requires startup of instance "stdby1" on database "stdby1"
Starting instance "stdby1"...
ORACLE instance started.
Database mounted.
Switchover succeeded, new primary is "stdby2"
-------------------this is my second switchover -------------
DGMGRL> switchover to stdby1
Performing switchover NOW, please wait...
New primary database "stdby1" is opening...
Operation requires shutdown of instance "stdby2" on database "stdby2"
Shutting down instance "stdby2"...
ORA-01109: database not open
Database dismounted.
ORACLE instance shut down.
Operation requires startup of instance "stdby2" on database "stdby2"
Starting instance "stdby2"...
Unable to connect to database
ORA-12514: TNS:listener does not currently know of service requested in connect descriptor
Failed.
You are no longer connected to ORACLE
Please connect again.
Unable to start instance "stdby2"
You must start instance "stdby2" manually
Switchover succeeded, new primary is "stdby1"
DGMGRL>
Edited by: user6981287 on Jan 7, 2010 12:57 AM
Edited by: user6981287 on Jan 7, 2010 1:00 AM

Understanding 7-Mode 'license show' command output

What does the "-"/hyphen/dash mean in the Expiration field? How does one determine the current expiration of installed licenses based on this output? Package           Type    Description           Expiration
NFS               license NFS License           -
CIFS              license CIFS License          -
FCP               license FCP License           -
SnapRestore       license SnapRestore License   -
SnapMirror        license SnapMirror License    -
FlexClone         license FlexClone License     -
SnapVault         license SnapVault License     - These services are currently active and in use yet, the Expiration field doesn't appear to reflect that we are licensed for them. I would expect it to at least say something other than the current output. This is confusing when trying to troubleshoot a potential licensing issue. Thank you in advance. I greatly appreciate it!

Flippin Mango - Those are licenses with no expiration date, hence the blank field.See also the license command man page https://library.netapp.com/ecmdocs/ECMP1511537/html/man1/na_license.1.htmlThe only time I've seen expiration dates listed is when I've given a customer a temporary demo license for a feature.We also use temp license keys for lab excercises in the NetApp classes we teach. Noticed your login name.Had to share that my home in the US is in Flippin, Arkansas. : )
I hope this response has been helpful to you.
At your service,
Eugene E. Kashpureff, Sr.
Independent NetApp Consultant http://www.linkedin.com/in/eugenekashpureff
Senior NetApp Instructor, IT Learning Solutions http://sg.itls.asia/netapp
(P.S. I appreciate 'kudos' on any helpful posts.)

Can i amalgamate two apple accounts into one? I had one for itunes years ago and created a new one when I got my iphone recently.

I have two apple IDs, one I created years ago for itunes and another I just created for my new iPhone 4S. Is there a way to merge the two accounts into one?

"Is there a way to merge the two accounts into one?"
No.
Why did you create a new one?
Just change the e-mail address associated with the original.

EEM variable for show command output and create a filename

Similar Messages

Maybe you are looking for