Equium M40X: System information and devices issue.

I have just purchased a Equium M40X and done a complete new install with Windows XP Pro.. I saved the drivers from the original software loaded and all have loaded sucessfully apart from a PCI driver. I went to Sys information and problem devices and this is what it came up with..PCI\VEN_104C&DEV_8034&SUBSYS_FF031179&REV_00\4&AD1 B67F&0&24F0 Can anyone enlighten me as to what this could be as it is driving me nuts.
many thanks

Hi, according to http://www.pcidatabase.com/vendor_details.php?id=308 PCI Vendor 104C belongs to Texas Instruments. Although DEV 8034 isn't listed I am certain this is the firewire port (OHCI-Lynx IEEE 1394 Controller) since it is in the rage of 0x8000. As for fixing your problem I have no idea you could try deleting the PCI entry and let XP re-detect hardware again. If that doesn't work maybe a driver update from TI perhaps??
Richard S.

Similar Messages

Hi folks, you might know how to fix this: my wifi shows (no hardware installed) then I went to system preferences and deleted the wifi connection, I went also to system information and I can not see wifi listed on Network, how can I create a new wifi ?

Hi folks, you might know how to fix this: my wifi shows (no hardware installed) then I went to system preferences and deleted the wifi connection, I went also to system information and I can not see wifi listed on Network, how can I create a new wifi or simply solve this, I have tryied shotdown pressing keys like P and R, option, etc. Please help me .

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

How do I uninstall Mackeeper? I have dragged it into trash, but it still showing in systems information and causing problems!

How do I uninstall Mackeeper? I have dragged it into trash, but it still showing in systems information and causing problems!
Please advise

How to uninstall MacKeeper - updated
How to Remove MacKeeper
Uninstalling Software: The Basics
Most OS X applications are completely self-contained "packages" that can be uninstalled by simply dragging the application to the Trash. Applications may create preference files that are stored in the /Home/Library/Preferences/ folder. Although they do nothing once you delete the associated application, they do take up some disk space. If you want you can look for them in the above location and delete them, too.
Some applications may install an uninstaller program that can be used to remove the application. In some cases the uninstaller may be part of the application's installer, and is invoked by clicking on a Customize button that will appear during the install process.
Some applications may install components in the /Home/Library/Applications Support/ folder. You can also check there to see if the application has created a folder. You can also delete the folder that's in the Applications Support folder. Again, they don't do anything but take up disk space once the application is trashed.
Some applications may install a startupitem or a Log In item. Startupitems are usually installed in the /Library/StartupItems/ folder and less often in the /Home/Library/StartupItems/ folder. Log In Items are set in the Accounts preferences. Open System Preferences, click on the Accounts icon, then click on the LogIn Items tab. Locate the item in the list for the application you want to remove and click on the "-" button to delete it from the list.
Some software use startup daemons or agents that are a new feature of the OS. Look for them in /Library/LaunchAgents/ and /Library/LaunchDaemons/ or in /Home/Library/LaunchAgents/.
If an application installs any other files the best way to track them down is to do a Finder search using the application name or the developer name as the search term. Unfortunately Spotlight will not look in certain folders by default. You can modify Spotlight's behavior or use a third-party search utility, EasyFind, instead.
Some applications install a receipt in the /Library/Receipts/ folder. Usually with the same name as the program or the developer. The item generally has a ".pkg" extension. Be sure you also delete this item as some programs use it to determine if it's already installed.
There are many utilities that can uninstall applications. Here is a selection:
    1. AppZapper
    2. AppDelete
    3. Automaton
    4. Hazel
    5. AppCleaner
    6. CleanApp
    7. iTrash
    8. Amnesia
    9. Uninstaller
10. Spring Cleaning
For more information visit The XLab FAQs and read the FAQ on removing software.

System Preferences and Safari issues

Hi I have a very concerning issue with system preferences and a smaller issue with Safari (7.0). When I open system preferences and navigate to the "internet accounts" page and try to remove an account or click the "Advanced" button, nothing happens. I see a faint flicker of the system prefs window but nothing changes. Another example is when I click on the "networks" page and try and open the "Advanced" window, nothing happens. I also can't sign out of iCloud or view my iCloud account information the buttons seem to do nothing. I've already tried installing mavericks again, deleting appropriate plists, resetting PRAM/NVRAM, repairing the disk and repairing disk permissions to no avail and I really need to find a solution. If this helps, the guest account does not have any issues described above. The safari issue is minor but when Safari opens, there is a gray box around the page title in the top bar of safari no matter what webpage im on. I have tried resetting safari, deleting caches and extensions but nothing works. I really appreciate any help with these issues.
Here is an example of the Safari issue.

Do you have the installer DVD? If you do:
Clean Install of Snow Leopard
Be sure to make a backup first because the following procedure will erase
the drive and everything on it.
     1. Boot the computer using the OS X Installer Disc or the Disc 1 that came
         with your computer. Insert the disc into the optical drive and restart the computer.
         After the chime press and hold down the "C" key. Release the key when you see
         a small spinning gear appear below the dark gray Apple logo.
     2. After the installer loads select your language and click on the Continue
         button. When the menu bar appears select Disk Utility from the Utilities menu.
         After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
         size.) Click on the Partition tab in the DU main window. Set the number of
         partitions to one (1) from the Partitions drop down menu, click on Options button
         and select GUID, click on OK, then set the format type to MacOS Extended
         (Journaled, if supported), then click on the Apply button.
     3. When the formatting has completed quit DU and return to the installer. Proceed
         with the OS X installation and follow the directions included with the installer.
     4. When the installation has completed your computer will Restart into the Setup
         Assistant. Be sure you configure your initial admin account with the exact same
         username and password that you used on your old drive. After you finish Setup
         Assistant will complete the installation after which you will be running a fresh
         install of OS X. You can now begin the update process by opening Software
         Update and installing all recommended updates to bring your installation current.

Retrieving Creative System Information and Software Autoupdate Iss

Hello,
I've been having a problem with a few things in my X-Fi Platinum software.
First when I attempt to retrieve the System Information using the Creative tool, I get an MS error report stating a problem with ctsi.exe and as such I've been unable to send proper information to tech support, so I'm attempting here.
Second whenever I attempt the Software Autoupdate I get another MS error report and the program closes down stating a problem with iexplore.exe . I get as far as installing the Acti've X controls, but shortly after installation the error report pops up and my browser closes down. I've attempted to remove the Acti've X controls and reinstall it but to no avail. I've un then reinstalled the software and drivers but with no hope towards this issue. I have reinstalled IE
These features were working for me on my last configuration, however after changing motherboards when the previous died, it has come to an abrupt end. The previous motherboard was an older version from the newly installed. I am unable to determine if this is a mobo issue as the only problem I have with this system is certain aspects of the sound cards' software, and the mobo is the only change that has been made.
My relevant system specs are as follows:
Motherboard: Asus P4P800 SE
CPU: 3.0 GHz Intel Pentium Prescott
RAM: Gb Kingston
Chipset: Intel 865PE, ICH5R
OS: Windows Media Center 2005 Edition
I have attempted a clean install of the operating system itself, installed all Windows updates aside from .NET Framework 2.0, and also reintalled Direct X.
I looked into other trouble threads with no solution found although there may seem to be Asus issues, the only difference is a slightly different model, (previous motherboard was an Asus P4P800X and everything ran fine with the Creative software). These are the only two features that are not working for me, every other aspect runs perfectly fine. On my previous configuration, there were a few critical updates installed, however when searching the downloads section, those same updates are not available there. MCE and XP I understand are almost hand in hand, but would rather not use the wrong firmware or drivers by any means.
I am at a loss, any help would be greatly appreciated including any relevant threads I may have overlooked. If any other information is needed to troubleshoot the issue, please let me know.
Thanks

You might just try reinstalling the drivers & software first, see this http://forums.creative.com/creativel...d=23573#M23573

Equium M40X-149: DirectX (Direct 3D) issue playing Loaded Silent Hunter III

Loaded Silent Hunter III in December 2005 after adding 512Mb RAM (total now 1Gb). Game has been running fine until now. Suddenly game fails to load with error message 'Cannot start 3D engine'. Have loaded latest Intel driver (dated Feb 06). Have loaded latest DirectX (v 9c) from MS site (dated Dec 05). Have uninstalled and reinstalled game from DVD. Still fails. DxDiag states 'Direct 3D functionality not available'....but it has been.
Game suppliers have run out of ideas.
You folks are my final hope...I'm going 'cold turkey' without being able to launch torpedos at ships!
All help gratefully accepted.
Peter

Hi
As far as I know this unit was delivered with a Mobile Intel 915GM Express Chipset AlvisoGM graphic card.
Toshiba recommend to use the own graphic card drivers because they are especially designed for notebook usage.
Please check this driver website:
http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=EU
There you should find a driver version 6.14.10.3943.
But generally its not easy to say why you game wont run.

No System Information in Service Desk message creation

Hello,
I'm trying out all the ways to use de message creation in service desk.
When i try to create a message directly from SOLMAN_WORKCENTER\Incident Management
No infos are filled in System Information and so i can't send the message. I can't even choose one
I checked in transaction BP but i can't put the finger on it..
Thanks in advance for your help

Hello,
Please check in IB52 if there is an Ibase with external ID SOL_MAN_DATA_REP.
Best regards,
Miguel Ariñ

Equium M40x-189: DVD DL Formats

Hi,
I've recently bought a Toshiba Equium M40x 189 laptop, and have read the manual regarding DVD formats that can be written to. However, I would like to know whether or not this laptop can write a DVD-DL dvd, I know in the manual it says it can write a DVD+DL, so i'd just like to know....Hope someone can help.
Thanks
David.

Hi,
Yesyou can write DL discs with this machine.
I would reccomend that you stick to major brands like Maxell, TDK or Verbatim.
Regards,
Nick

Why are there two graphics cards listed in system information?

I have a MacBook Pro 5,1 2.53 Ghz. I am using Photoshop which brings the machine to a standstill, or so it seems. I looked in system information and discovered that there are two different nvidia GEFORCE graphics adapters listed...one 9400 and one 9600. Is there a way to select the 9600 which shows 512 mb or video ram versus the 9400 which only shows 256 mb? I am hoping that the extra video memory will improve performance. Or is this 9600 connected only to the video output and not to the built in screen?
Thanks for your assistance in advance!

Thanks very much Niel!
I guess I knew about that setting, but did not realize it actually changed the graphics card that was selected! Already seems to be better after logging back in on the MBP!
Shawn

How to find System information Of Enterprise Portal from OS/DB level

HI All.
How to find the system information of Enterprise Portal from OS/DB level. like system name, version, stack.
ITS VERY URGENT
Thanks in Advance.
Mahesh

Hi Mahesh,
here is where you can find the system information about your EP installation (i.e. O/S, DB, components release, etc):
1- Goto the Web AS Java URL (http://<host>:<port>)
2- Select "System Information" and log in as an administrator user
3- After logging in, the system information page displays the O/S, DB, application server level
4- Select "Software Components", select the link "all components" (upper right corner of the table) and then you should be able to see the version of your components/applications
Hope this answers your question.
Regards,
Joseph

What type of files are in "Other" under "System Information Storage" on MacBook Pro?

Hi happy folks,
I need to clear up space on my MacBook Pro. When I open System Information and click on Storage, it says that 200G of my 250G are taken up by "Other." Not photos, not movies, not apps. I don't have that many documents. What constitutes this massive Other and how can I clear off some of this space?
Thanks!

This article explains what is contained in "other."
OS X: What is "other" space in About This Mac?
Barry

USB storage devices not shown in Finder, yet function, and show in System Information?

Occurring starting about last month, this has gone from a seldom, to all the time situation. plugging in any USB memory device either directly to the computer, or with cables, will allow the files to be accessed/changed/deleted by programs, but the device with it's files will not show in finder. The device shows in System information. I have set Finder to show everything, but they no longer apear. Before failing entirely, I would sometimes have the device show for a short time, then get an "Improper removal" error, without touching the device, after a few moments. All these memory devices still function properly when used in external devices and when direcly accesed by software. Not being able to use finder to modify content is a significant problem.

Well I'm about out of ideas. Going off what you described, these devices work fine elsewhere and gradually failed on your computer.
Unless someone else can post other ideas, I only can suggest a reinstall of Lion from scratch. I would make sure I had a good backup from TM and an additional backup of your important files just in case.
Probably the easiest way would be to make a bootable USB stick or drive to work from. Procedure here: http://osxdaily.com/2011/07/08/make-a-bootable-mac-os-x-10-7-lion-installer-from -a-usb-flash-drive/
If you can accomplish that, see if you can boot from it. If so, use Disk Utility to erase the main drive and reformat it. Verify the drive is OK. Then quit Disk Utility abd procede to install Lion.
When the installation is finished, reboot and use Setup Assistant imediately to migrate your user data and applications back from the TM drive. Don't use migration assistant later.
I doubt it will help since the Comb-Update didn't fix it, but who knows.

How to get the health , performance information and about the services run on devices that have connected to the system center?

Hi All,
I want to know how to get the health , performance information and about the services run on devices that have connected to the system center to my c# application. Also I need to know about the information of databases that have connected to system center.
I will appreciate your feedback
Thank you

Hi,
You can configure service monitor for the required service on the server
refer below link for how to configure service monitoring
http://www.bictt.com/blogs/bictt.php/2011/03/17/scom-monitoring-a-service-part3
You can use SCOM SDK to connect to the scom server using c# and get required information
http://msdn.microsoft.com/en-us/library/hh329086.aspx
you can find the database in below registry path on management server
HKLM:\SOFTWARE\Microsoft\Microsoft Operations Manager\3.0\Setup\DatabaseName
Regards
sridhar v

If in my Hardware section of System Information, when I select Thunderbolt and the reply is: Thunderbolt: No hardware was found, does that mean the computer does not contain Thunderbolt or that no Device using Thunderbolt is attached?

If in my Hardware section of System Information, when I select Thunderbolt and the reply is:
Thunderbolt: No hardware was found,
does that mean the computer does not contain Thunderbolt or that no Device using Thunderbolt is attached and that the computer does have thunderbolt?
I have Lion and both my Mini Server and Macbook Pro are less than a year old, however both were bought from Apple as reconditioned units so they might be older, and I expected they would have Thunderbolt but when I connect a Black Magic Intensity Extreme unit which is a thunderbolt powered and driven Device using a Thunderbolt Cable to either computer, it is not recognized.

No other information in Sys Info and I guess as both units, Mini and MBPro, were reconditioned, they were pre July and February , 2011, respectively.
I don't suppose there is any way to add Thunderbolt or USB 3.0 to prior generation Mac Products or get similar performance.

T500 Base System Device and PCI Device issue

Hello everyone,
I cant seem to find the right driver for the Base System Device. Earlier this morning, I had 4 ?s named Base System Device (under Other Devices in the Device manager). Once I ran the ThinkVantage System Update, the other 2 Base System Device have disappeared. How come I still have 2 listed that need to be updated? Also, the PCI Device has a ! sign. Any ideas?
I've already tried running the system update, and installed the Ricoh 4 in 1 card reader.
Thanks for your help.

Hello vondorsupport,
please take a look at these thinkpad superguide.
May be it will provide some usefull information for you.
Follow @LenovoForums on Twitter! Try the forum search, before first posting: Forum Search Option
Please insert your type, model (not S/N) number and used OS in your posts.
I´m a volunteer here using New X1 Carbon, ThinkPad Yoga, Yoga 11s, Yoga 13, T430s,T510, X220t, IdeaCentre B540.
TIP: If your computer runs satisfactorily now, it may not be necessary to update the system.
English Community Deutsche Community Comunidad en Español

Equium M40X: System information and devices issue.

Similar Messages

Maybe you are looking for