Error 0xBFF60492 on IMAQ USB snap.vi RT Video not support displaying selected color depth

Attempting to snap a picture with NI-IMAQ for USB in LabVIEW 8.0 using the following procedure.
1)I get the first enumerated camera, 2) open a session, with returned
string [0], 3) start a session, 4) snap a picture and 5) close
vi. My problem is that in step 4 with the IMAQ USB Snap.vi, I get
the following error.
Error -1074396014 occurred at IMAQ USB snap.vi
The image passed is not valid.
Possible Reasons(s):
IMAQ Vision: (Hex 0xBFF60492) RT Video Out does not support displaying the supplied image type at the selected color depth.
I give the snap.vi an Image in from rightclick->Create->Control
or rightclick->Create->Constant. The output image (on the
Front Panel) created by rightclick->Create->Indicator.
LabVIEW should insert the correct data structure to match the expected
input/output, and there is nothing I can that changes he color
depth. The GetImageInfo.vi reports that the camera is set up for
4 Bytes Per Pixel, with the rectangle 352x288.
Also the error message refers to RT Video Out, but I am using USB. This distinction is significant in NI Vision Assistant.

Hello together,
I wanted to use a Sanyo Xacti CG 10 video camara in LabView.
By using the NI-IMAQ for USB Snap I get the following error: IMAQ Vision: (Hex 0xBFF60492) Ungültige Blit-Funktion des Videoausgangs.
Is it possible, that I can not use this camera in LabView?
Thanks a lot for your reply

Similar Messages

Error 1074396024 occur at imaq usb snap.vi

hallo, ich habe labview 8.0 mit dem vision development modul und
benutze eine logitech webcam zur bilderfassung. ich habe ein vi
erstellt das im zeitraum von 1s ständig neue bilder macht und diese mit
einem referenzbild vergleicht. mein problem ist das so bei ungefähr
1000 vergleichen eines neuen bildes mit dem referenzbild der fehler
1074396024 occur at imaq usb snap.vi auftritt und ich aber nicht weiß
warum. würde mich freuen wenn mir jemand helfen kann

Please have a look at this thread which discusses similar issues in detail.
Best regards,
Jochen Klier
National Instruments Germany

IMAQ USB Snap.vi time out

I'm trying to capture an image in LabView using a veo stingray webcam.
I'm using LabView 7.1 with Vission Assistant 7.1. I've attached my
block diagram. When I press run LabView recognizes my camera, but I
always get the following error.
Error -1074396030 occured at IMAQ USB Snap.vi Time Out.
Any suggestions would be appreciated.
Attachments:
labview.JPG ‏30 KB

The QuickCam is indeed USB. The error appears when the vi is closed without using the IMAQ USB Close.vi (for instance when aborting the execution using the toolbar stop button). So, problem solved. Unfortunatelly this was not the only issue : Now my vi does not crash LV... but returns only a black image...
For professionnal use, I have several NI frame grabbers. For teaching, I don't have a budget for 16 firewire adaptators and cameras . I'll try re-installing the software one more time.
This is not a big problem because as I said before, the grab function is working. However, I don't like giving my students the idea that sometimes only 50 % of LabVIEW functions are working properly.
Chilly Charly (aka CC)
E-List Master - Kudos glutton - Press the yellow button on the left...

Why is IMAQ USB Snap.vi constantly giving out a 32-bit image?

Hi.
I'm using some USB cameras (uEye) with Direct Show. I use the IMAQ USB camera tools (with Labview 7.1, Vision 7.1.1) as in the examples. In particular I'm working in the snap mode.
I create an U8 image (IMAQ Create) which I use as input to IMAQ USB Snap.vi and I set the camera's video mode to grayscale (Y8) using IMAQ USB PropertyPage.vi
But, I don't get an 8-bit image out of IMAQ USB Snap.vi. The image is always converted to 32-bit RGB. In principal It works like this, but it costs me valuable time to convert the image to 8-bit at some points of the program where I need the image grayscale array.
Cheers,
mirola
Labview 5.1 - 2011

Hi Elmar,
Thanks for answering.
Of course, the "not officially supported" thing is a killer argument. But the device shall work with a laptop and, as I know, the firewire cameras need an additional power supply when connected to a laptop 1394.
The camera I use is grayscale and only works properly when I write 8-bit grayscale in its settings (e.g. using IMAQ USB PropertyPage.vi).
As I said, everything I can set is set to 8-bit. The Snap.vi converts the input IMAQ image to 32-bit.
But maybe you are right and it's just that NI's USB Direct Show dll is not treated with high priority (note: I use the most recent one, although I combine it with older LV and Vision versions.) Otherwise I guess I would get more answers here.
On the other hand, if I ask the manufacturer he will probably say I should use his SDK which I don't want at this point.
Best regards,
mirola
Labview 5.1 - 2011

I get the error message in QuickTime "operation stopped the operation is not supported for this media" most times when I try and export an .AVI file as something else (.m4v). I have not touched the file in any way (no trimming, clipping or other editing)

I get the error message in QuickTime "operation stopped the operation is not supported for this media" most times when I try and export an .AVI file as something else (e.g. .m4v). I have not touched the file in any way (no trimming, clipping or other editing), all I want QuickTime to do is export the file in a compressed format. Bizzarely, if I shutdown and open QuickTime many times I can occasionally export a clip as another format (maybe one in 10 times). I have seen that other users have had a similar problem after clipping files in QuickTime but this seems to be a slightly different bug in that all I do is open the file and then try and export the file as is - either way, this is a very annoying bug

@Z_B-B, thank you for taking the time to respond to my cry for help. However, the link you supplied does not address the problem: I am not trying to export from Final Cut Pro to QuickTime, I am trying to export from QuickTime to the rest of the world (like people's iPhones and Ipads) in .m4v format (so I am not emailing my freinds such huge files).
If I were to spend hundreds of Dollars on a copy of Final Pro I could export directly from there and not have to bother with QuickTime, but I do not take enough video clips to justify the cost. I must say that I never had any of these problems before I decided to switch from Snow Leopard to Mountai Lion.

IE Error: "The content you are trying to view is not supported in the current Document Mode..."

My Captivate 7 project (HTML5) runs just fine on my computer in IE11. My client tried to run it from IE9 and got the following error:
"The content you are trying to view is not supported in the current Document Mode of Internet Explorer. Change the Document Mode to Internet Explorer 9 Standards and try to view the content again. To change the Document Mode, press F12, Click Document Mode:, and then select Internet Explorer 9 Standards."
My guess is that they're running it over their LAN, and IE is subsequently running in quirks mode.
I've changed the metadata in index_SCORM.html from
<meta http-equiv="x-ua-compatible" content="IE=10">
to
<meta http-equiv="X-UA-Compatible" content="IE=edge,chrome=1">
we'll see if that fixes it....

TLCMediaDesign wrote:
I've seen a lot of threads about getting rid of these kind of messages. Those messages are there for a reason most of the time. If you have CSS animations or other HTML5 standards that cannot be rendered in IE9 they won't magically start working becuse you got rid of a message. I use IE9 since that is the minimum standard for the client. I have never seen that message publishing to HTML5 content.
IMO, if your client has IE9 I think that you should develop with IE9 in mind not IE11.
When you say "develop with IE9 in mind not IE11" do you mean use SWF instead of HTML5? I used the standard question types, and a converted PowerPoint presentation. I didn't add anything out of the ordinary.

Avorcldb verify - ERROR: specified version 10.2.0.1.0 is not supported

Hello all,
I got this error when verify operation of source compatibility with the Collectors:
Audit Vault Server: Windows Server 2003, Oracle 10.2.0.3
Audit Vault Client: Windows Server 2003, Oracle 10.2.0.1
Run this command on Audit Vault Server:
E:\>avorcldb verify -src 10.10.70.51:1521:orcl -srcusr system/oracle -colltype ALL
source ORCL.REGRESS.RDBMS.DEV.US.ORACLE.COM verified for OS File Audit Collector collector
source ORCL.REGRESS.RDBMS.DEV.US.ORACLE.COM verified for Aud$/FGA_LOG$ Audit Collector collector
ERROR: specified version 10.2.0.1.0 is not supported
Please provide me any infomation to fix this error.
Do I need to upgrade the Audit Vault Client to 10.2.0.3 ?
Thanks.

Thank Damorgan,
It's ok after upgrading to 10.2.0.3.
But now I get another errors, please help:
urgent: could not get AV agent connection using jdbc:oracle:oci:@AV
Thanks.

TOAD ERROR : OCI version 10.2.0.1.0 is not supported

Hi all,
Previously i have oracle 9i in my system, now i installed oracle 10.2.., after this when i am trying to retrieve data from tables im getting this error "OCI version 10.2.0.1.0 is not supported". Please help me how can i solve this problem.
Thanks in advance

You need deinstall the old version of toad and install version higher than V 8.5 which will fix the issue. Because the default home is read by Toad sometimes reinstallation will fix the issue.
--kccrga

Sub-items not supported for selected item(s) error in LSMW

Hi gurus,
Am working on BOM's data load via LSMW. Most of the item are stock items (L) but some of the items i am loading are Text items (T). Because of the customizing done in OS13 (that can't be changed apparently), the LSMW executed in foreground gives the message "Sub-items not supported for selected item(s)" (only as information, green message) and the dataload IS STOPPED.
Is there a way to :
-> change OS13 (allow sub-items for text items) : When i try i have an error message.
-> or to force LSMW program no to go on the sub items screens (this way the program does not stop and the BOM is created)
Thanks in advance for your answers,
Olivier

Found the solution my self all relations between dataload file and sub-items structure had to be suppressed in LSMW.

Secure zone - ERROR: The payment gateway that you are using does not support recurring payments

So I want to sell a product that is made up of 4 downloadable products. (Totalling ~ 200meg)
The only way I have found is to sell membership to a secure area where the files are linked.
When I create the secure zone, I want a one-time-fee, but the system says:
"ERROR: The payment gateway that you are using does not support recurring payments"
The payment isn't recurring!
Micah

"Note that you have to use seamless gateway to process such payments."
Right, but that's the problem, we're not usiong a seamless gateway and thus we get the error. Again, the system should note that we're doing a one-time charge and not throw the seamless gateway error.
Micah

I have air port express 802.11n and imac ver 10.7.5. When I try to set up my wifi I get error message 'that the version mac os x is not supported' Help?

I am trying to set up wifi using air port express 802.11n version 1.3 on my imac os x ver 10.7.5. Get error message Air port can't be installed on this disk that the ver of mac not supported - Help????

Please check the model number on the side of the AirPort Express in the faint print. It will start with an "A" followed by four numbers, as in A x x x x.
Post back with your findings.

Getting this error when saving: Names longer than 31 characters are not supported on the destination volume

I've just tried to save a document in Pages and got this error
Names longer than 31 characters are not supported on the destination volume
Never had a problem like this before. I haven't changed disks or formatted disks. Running latest Yosemite 10.10
The only reference I can find to this error on the internet says that it's for applications prior to OS X which I think we can discount.
The only other reference I can find in the support community relates to one person with problems saving attachments in Mail and dates from early 2014.
Can anybody give me a suggestion on what I might need to do?
Thanks

What format are you saving to?
Where are you saving the files to and what is that volume formatted as?
Have you tested with files from other applications, such as TextEdit?
Peter

Error-Grant Evalution posting-"Account assignment to grant is not supported

In t-code PQ_GRANT_CALC Grant evaluation, i can see the line for the Grant Info. But the same is not getting posted.
while posting it is showing the error "Account assignment to grant is not supported".
I can see the fee calculation for the student and posted the same to the student account.the fee is not getting posted aganist the grant.
(even we have tried grant evalaution posting before posting to the stuent account)
Pls hlep me, i have assigned the grant in the FMDERIVE and also in GMDERIVE.
In the Student master file, in the GRANT Assignment tab, i have mentioned the required data,i,e
assigned Grant and internally managed also.
I can able to post the Budget DOC in Grant.
Hope ,if i post the Student Doc in SLCM(t-code PIQST00 ), for the Grant amount entered in Student, it will reduce the amount of Grant created in the Budget?

not done

Roving error message on black screen at start up "Input not supported)

HP Pavilion media center a1547c, running XP. Changed the resolution because the icons appeared larger and the screen went black with a roving error message "Attention: Input not supported" message box is white with grey stripes top and bottom. On restarting, WindowsXP logo comes up, then error message appears but I can hear the Windows "chimes". Anyone?

Start Windows XP in safe mode. Press the power button and then begin tapping the F8 key before Windows boots up. Choose Safe Mode with command prompt. While in safe mode, start system restore by typing rstrui.exe and pressing enter. Choose a restore point dated before before the initial problem began. This may resolve the issue. If it does, fantastic. If not, then continue with the troubleshooting as described below.
When Windows restarts consider two troubleshooting scenarios to isolate the issue. What you need to know is whether the problem lies with the PC's video output of the LCD display.
1) connect a different display to the PC and log into Windows to see if the windows desktop is normal.
2 )install a low powered (inexpensive and less than 1GB VRAM) PCI Express x16 video card. You need to see if that corrects the display issue with the original display connected. That will show you if the motherboard's video output is the issue.
Don't forget to post your result here in your thread.
Best regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

WindowsAzure REST API AddDataDisk "Error 404 : The resource service name hosted services is not supported"

Hello I am trying to create a secondary disk attached to a Windows Azure LINUX VM.
I sent the HTTP POST message body
    <?xml version="1.0" encoding="UTF-8"?>
   <DataVirtualHardDisk xmlns="http://schemas.microsoft.com/windowsazure"xmlns:i="http://www.w3.org/2001/XMLSchema-instance">
       <HostCaching>ReadWrite</HostCaching>
       <DiskLabel>49192cf1-cd65-4750-83bf-1fb5a337493d-sdf</DiskLabel>
       <DiskName>49192cf1-cd65-4750-83bf-1fb5a337493d-sdf</DiskName>
       <Lun>1</Lun>
       <LogicalDiskSizeInGB>40</LogicalDiskSizeInGB>
       <MediaLink>https://accordscentralus.blob.core.windows.net/vhds/49192cf1-cd65-4750-83bf-1fb5a337493d-sdf.vhd</MediaLink>
   </DataVirtualHardDisk>
to the endpoint URL ( the url has been line split for clarity here only )
https://management.core.windows.net
       /{subscription-identifier}
       /services/hostedservices/54f84578testsmallubuntuw
       /deployments/9e8e1e43-d13a-4cfb-bd5b-19f6421f40dd
       /role/54f84578-testsmall-ubuntu-with-cosacs-volume
       /DataDisks
with the header
x-ms-version : 2014-05-01
and receive the same response no matter what I try:
404   Not Found
   <Error xmlns="http://schemas.microsoft.com/windowsazure" xmlns:i="http://www.w3.org/2001/XMLSchema-instance">
       <Code>ResourceNotFound</Code>
       <Message>The resource service name hostedservices is not supported.</Message>
   </Error>
The virtual machine has been correctly started, and is perfectly useable, but the secondary disk can not be created.
I have seen a few blogs and posts that say that I should not send the DiskName in the message but I need to be able to predict the name of the disk in order to be able to restart the VM with the correct disk.
Is there anyone that can help me to make sense of this.

Ok I have tested this again several times and have consistantly observed the following results.
The first time round for an new instance and a VHD that does not exist:
The request
POST https://management.core.windows.net:443/{subscription}/services/hostedservices/54f8cc27testsmallubuntuw/deployments/80388771-1cd2-4fe2-9637-6a06659840df/roles/54f8cc27-testsmall-ubuntu-with-cosacs-volume/DataDisks
<?xml version="1.0" encoding="UTF-8"?>
<DataVirtualHardDisk xmlns="http://schemas.microsoft.com/windowsazure" xmlns:i="http://www.w3.org/2001/XMLSchema-instance">
   <HostCaching>ReadWrite</HostCaching>
   <DiskLabel>d-80388771-1cd2-4fe2-9637-6a06659840df-sdf</DiskLabel>
   <Lun>0</Lun>
   <LogicalDiskSizeInGB>40</LogicalDiskSizeInGB>
   <MediaLink>https://accordscentralus.blob.core.windows.net/vhds/d-80388771-1cd2-4fe2-9637-6a06659840df-sdf.vhd</MediaLink>
</DataVirtualHardDisk>
Returns
HTTP/1.1 202 Accepted
and the VHD disk is created and attached to the virtual machine instance.
Inspection of the instance through the Windows Azure Portal using virtual machines->instances->dashboard we see the two disks attached to the instance.
The second time round, after terminating and deleting the instance and root disk VHD but not the extension disk VHD, whn creating and deploying a new virtual machine instance to use the existing VHD created in the first case.
The same request is sent as above, but with a different instance, role and deployment information, and it returns the same
202 Accepted signalling success but the already existant VHD does not get used and does not get attached to the virtual machine instance. In fact no extension disk gets attached to the instance at all.
Inspection of the instance through the Windows Azure Portal using virtual machines->instances->dashboard we see only one disk attached to the instance.

Error 0xBFF60492 on IMAQ USB snap.vi RT Video not support displaying selected color depth

Similar Messages

Maybe you are looking for