Error code 10 for Intel 5300 Wireless Card

Hi,
I tried to install a new Intel 5300 Wireless Card in my Thinkpad T400.
However, it is not very successful.
After I installed the driver, I find a yellow exclamation point on the 5300 Wireless Card on the device manager and an error code 10 (can't start device).
I have tried to re-install the driver but still no luck.
Could anyone help for this?
Thanks a lot
Here is some information might be useful:
Operating System: Windows XP (SP3)
Driver download from Lenovo: http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-70504
Wireless Card bought from ebay (The seller said this card can support IBM/LENOVO T400).

Unless the card is a Lenovo Branded card, it won't work. But since you aren't complaining about an error in BIOS about an unauthorized card, then you also might have put it in the wrong slot.
Check the Hardware Maintenance Manual for your particular system and make sure you have it in the WLAN slot, not the WWAN slot.

Similar Messages

Tip: Temp work around for Intel 7260 wireless card problems

I am currently having lot of issues with the Intel 7260 wireless card relating to unstable network connections (i.e. limited or no network connections, frequent dropouts). These problems are quite widespread, so it is not limited to Lenovo branded machines, many other brand of laptops are also having similar problem. This workaround is temporary until the laptop company and intel provides an official fix.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Step 1. Go into your control panel -> System Security -> System
Step 2. Click on Device Manager on the left hand side of the window.
Step 3. Click on Network Adapters
Step 4. Right click on Intel Wireless 7260, and click on properties
Step 5. Click on Advanced Tab
Step 6. Click on HT Mode and then select disable as an option.
Disabling the HT mode means you are operating the wireless card in G mode (54 mbps), for some people this is too slow, but it is an acceptable short term solution for preventing frequent network connection dropouts.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Intel 5300 wireless card not working

if i run a scan in terminal i get the following:
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=70/70 Signal level=-39 dBm
Encryption key:off
ESSID:"linksys"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s
Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
which means it is detecting my wireless router. why can i not connect to it at all?
Cheers

This should get it going
sudo ifconfig wlan0 up
sudo iwconfig wlan0 essid network key password
sudo dhcpcd wlan0
network = network name and password = network key
https://wiki.archlinux.org/index.php/Ne … _interface

Intel pro wireless card can not connect

Since some weeks, i can not use my wireless network, it does not associate the access point.
The cared is a intel pro, using the agn driver.
I can not connect to my wep key protected home network, or public, unprotected accesspoints.
I tried various parameters with iwconfig, without success, so I assume the kernel module is broken.
Any help would be appreciated.

B wrote:
sredna wrote:Yes, I read the wiki page. Yes, everything is installed. It worked for a long time. I read the various manuals. I do it the correct, recomended way. It just does not work.
Rather than blaming devs for putting out faulty software, if I were you I'd look at myself - the PEBKAC problem . So an upgrade broke it. When was this? What packages where upgraded? Check your pacman log (yes, it exists).
You are aware the module name for Intel's wireless cards changed? Instead of referring to the card model it's now iwlcore and iwlagn. But then again, if you let udev figure it out, there shouldn't be the slightest problem in that upgrade.
Care to share any of your cherished errors? Without them there's not much we can do. The BBS has been out of crystal bowls for a long time.
Dear mr. B, I do not blame anybody anything. I report, as is, it does not work. On my system, in the hope that someone have something meaningful to say, not because I hoped for you to call me names. I do not know what your acronym means, and I do not wish to find out, since it appearently is there to make me less. I do not care for that.
The kernel modules that are loaded on my system, and was back when I had working wifi support, are iwlcore and iwlagn. I do not know that the iwlwifi-4965-ucode package is used for anything, I installed it because the before-mentioned wiki page recommends that, and I did get working support. I do not try to configure it by hand, I trust udev/hal/whatever is there to handle the hardware.
But, sorry for repeating, since some time, I can not connect to an access point. No matter if I try cli commands or use wicd or networkmanager applets. The result appears to be the same, there is no error from iwconfig, which does not succeed.
I can't even remember the date it went wrong, but i know that the kernel was updated as a part of that particular update. rolling back the kernel did not help though.

My ipod wont let me buy any apps because it says i have an invalid security code for my moms credit card but its the right one. and it also says i owe money for upgrading an app does anyone know how to remove my moms credit card cause i cant figure itout

my ipod wont let me buy any appps because it says i have an invalid security code for my moms credit card but its the right one. and it also says i owe money for upgrading an app does anyone know how to remove my moms credit card cause i cant figure itout

To change asccount information see:
Changing Account Information
For the code issue this may help.
iTunes Store: My credit card's security code or zip code does not match my bank's records
For a standard iTunes account you need a valid payment method even for free apps and app updates.
What is making it think that you own money for an app upgrade?

Same error code for two different errors

I have a simple state machine with a few states, two of which are read ini file and read GPIB data. I also have an error handling state where I would like to handle all errors. Errors are checked for on each iteration of the loop, passed by shift register. However, I can't just unbundle the error cluster and wire the error code to a case structure because if the ini file doesn't exist (error code 7) I want to exit the program. But if I get error 7 from the gpib (Nonexistent GPIB interface) I want the program to continue running. What is the best way to track where the error is coming from so I know how to handle it when two error codes for different errors have the same error code value?
Message Edited by for(imstuck) on 01-27-2010 03:47 PM
CLA, LabVIEW Versions 2010-2013

Another option is to check the existence of the file before opening the config file, then exit the program if nessecary. Relying on error codes might be a bad option.
Ton
Free Code Capture Tool! Version 2.1.3 with comments, web-upload, back-save and snippets!
Nederlandse LabVIEW user groep www.lvug.nl
My LabVIEW Ideas
LabVIEW, programming like it should be!

Where to find LED error codes for Portege 4010?

Hi,
My Portege 4010 isn't working, and the AC indicator is blinking an error code (either 0xA or 0x50 depending if I should interpret the first bit as least or most significant). I've tried searching, and I've found a fairly detailed guide that includes these error codes for the Portege M100 and M300 (at http://tim.id.au/laptops/toshiba/portege%20m100.pdf and http://tim.id.au/laptops/toshiba/portege%20m300.pdf) but I can't find anything for the 4010. So can anyone give me a location (ideally official Toshiba) for a document detailing the meaning of the error codes for my model?
Thanks,
Jes

See for 'REP messages' in help menu.

Ora (OCI) error codes for TAF failure

Hi,
I am working on project where in I have to support Transparent Application Failover (TAF) in GUI (using Java). From web (by googling) I found that this is automatically done by JDBC Thick (OCI) drivers.
I also found in some web site that there are lot of Ora Error Codes for various senarios like SELECT TAF failure(Ora 25401), or for DML command TAF failure(Ora 25402).
Is there any set/range of Ora(OCI) Error Code which is specifically for all TAF failure senario?
Thanks
Ram

:-)

Error Code 10 Intel 82579LM LAN connection on Portege R830-13C

After recent Windows 7 32 Bit update, the LAN connection is failing to start (Code 10) under device manager
"This device cannot start. (Code 10)"
I have tried uninstalling drivers / rolling back / and installing the following files from Toshiba support pages, but does not resolve the issue.
- lan-20110330164846
- fareg-20110331130330
How do I get Intel 82579LM Gigabit Network Connection on Portege 830 -13C to work?
(wireless is fine)

Hi
Error Code 10 is generated when Device Manager can't start the hardware device and usually its caused by outdated or corrupted drivers.
Therefore I think that driver installation should help to sort out this issue.
I would recommend doing this:
- Go to device manager and uninstall the LAN driver
- Reboot the notebook but dont install the driver
- Install the CCleaner and clean the registry
- Reboot the notebook once again
- Then go to device manager, choose the LAN card (Ethernet controller) and install the downloaded driver
As option I would recommend testing the LAN driver from Intel page.

Intel 5300 wireless not working (iwalgn)

$ lspci | grep -i net
03:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300 (rev ff)
$ uname -a
Linux westley 3.1.2-1-ARCH #1 SMP PREEMPT Tue Nov 22 09:17:56 CET 2011 x86_64 Intel(R) Core(TM)2 Duo CPU T9400 @ 2.53GHz GenuineIntel GNU/Linux
My wireless card worked perfectly for quite a long time, but lately it's been a bit flakey. Coming out of standby often causes it to fail, and rebooting will sometimes, but not always, fix the problem.
The indicator light won't come on, and trying to bring the card up manually gives this:
The laptop's a T400, if that's any help.
$ sudo ifconfig wlan0 up
SIOCSIFFLAGS: Connection timed out
And dmesg looks like this:
[34123.748035] iwlagn 0000:03:00.0: L1 Enabled; Disabling L0S
[34123.750915] iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
[34123.750915] iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
[34123.784661] iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
[34123.798853] iwlagn 0000:03:00.0: Radio type=0x0-0x2-0x0
[34123.802162] iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
[34123.818812] iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
-- snip --
[34124.383259] iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
[34129.396705] iwlagn 0000:03:00.0: Could not load the INST uCode section
[34129.396712] iwlagn 0000:03:00.0: Failed to start RT ucode: -110
[34129.396739] iwlagn 0000:03:00.0: Unable to initialize device.
Any help would be greatly appreciated.
Last edited by stillinbeta (2011-11-28 04:18:20)

Until you get it fixed, you can tell pm-suspend to unload the wireless driver before suspending, then loading it again after resuming?

Can't set Intel 3945AGB wireless card to Ad-Hoc

When I try to set my wireless card to ad-hoc ...
[root@pwn max]# iwconfig wlan0 mode Ad-Hoc
Error for wireless request "Set Mode" (8B06) :
I was always able to do this until recently ... did an update break this? This is on what lspci reports as ...
03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
Last edited by synthead (2009-04-14 03:22:52)

I'm having the same issue with Arch64 on kernel 2.6.29.
lspci output:
0c:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
uname -a output:
Linux charon 2.6.29-ARCH #1 SMP PREEMPT Fri Apr 17 14:14:28 CEST 2009 x86_64 Intel(R) Core(TM)2 Duo CPU T5850 @ 2.16GHz GenuineIntel GNU/Linux
I've been able to get this working before with kernel 2.6.28 and wicd, but now it's not working with wicd or iwconfig. I've tried Googling around for a solution and found some bug reports, but haven't come up with anything recent. Any help is appreciated.
UPDATE: I found this bug report. Apparently it's an issue with the kernel itself that has been fixed numerous times. Any chance we could get this fixed permanently in the Arch64 kernel?
Last edited by lumpy211 (2009-04-24 22:31:38)

Event ID 1 for Intel Bluetooth Wireless High Speed after Windows Update

After the automatic update for Windows I received the following error message in the Event viewer, telling me that Intel Bluethooth Wireless High Speed has to be reinstalled after the update.
How do I reinstall Intel Bluethooth Wireless High Speed on my notebook?
Source: ApplicationExperienceInfrastructure
"Bei der Anwendung (Intel Bluethooth Wireless High Speed, von Lieferant Intel) sind folgende Probleme aufgetreten: Um eine einwandfreie Funktion zu gewhrleisten, muss Intel Bluethooth Wireless High Speed nach der Aktualisierung von Windows neu installiert werden."
+ System
- EventData
DBType 15
AppNameCount 36
AppName Intel Bluetooth Wireless High Speed
VendorNameCount 6
VendorName Intel
SummaryCount 149
Summary Um eine einwandfreie Funktion zu gewhrleisten, muss Intel Bluetooth Wireless High Speed nach der Aktualisierung von Windows neu installiert werden.
SessionID 0

Yeah, I tried it exactly as described.
I use the Satellite U940-11X (PSU6SE) which has as network adapters the Realtek PCIe FE Family Controler and the Intel Centrino Wireless Adapter N 2230. The OS platform is Windows 8, 64bit.
I first uninstalled the existing Intel Bluetooth driver, then the Intel ProSet Wireless software.
I downloaded the newest software from Intel's website which is:
- BT_2.6.1212_e64.exe, version 2.6.1212, 19-3-2013, for the Intel bluetooth software and
- Wireless_15.6.1_e64.exe, version 15.6.1, 19-3-2013, for the Intel PROSet/Wireless Software and Drivers
I have installed both software packages correctly and did not receive any error messages.
The installation seems to be faultless.
However, the bluetooth switch in PC settings (wireless tab) remains gray.
I cannot switch it from off to on.
In the device manager the bluetooth button is listed under hidden devices.
Where is the mistake?
Is it possible that my notebook requires specially modified drivers from the Toshiba website and/or additional drivers like to "bluetooth filter driver package" provided by Toshiba for my notebook model?
As to the bluetooth filter driver package it reads on the website that this driver is needed to enable bluetooth on your Atheros wlan-combo-card.
I am confused now because the notebook Satellite U940 11X (PSU6SE) doesn't have the Atheros card.
Any advice for me?
Thanks in advance
Rafu
Message was edited by: Rafu

Intel 5300 wireless issues

My fresh Arch 64 install doesn't appear to be recognizing the Intel 5300 interface at all.
I've reinstalled wireless_tools, iwlwifi-5000-ucode,
hwdetect --show-net results in:
NET : e1000e ppp_generic slhc mac80211 rfkill
ifconfig gives me:
eth0 Link encap:Ethernet HWaddr 00:21:70:B9:C0:FB
inet addr:149.166.142.83 Bcast:149.166.142.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:42407 errors:0 dropped:0 overruns:0 frame:0
TX packets:24349 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:48974218 (46.7 Mb) TX bytes:2501692 (2.3 Mb)
Memory:f6ae0000-f6b00000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:40 errors:0 dropped:0 overruns:0 frame:0
TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2000 (1.9 Kb) TX bytes:2000 (1.9 Kb)
The iwlagn module should be loaded:
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(e1000e iwlagn iwlcore snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-pcsp snd-$
bash-3.2# lsmod | grep iwl
iwlagn 102148 0
iwlcore 86468 1 iwlagn
rfkill 12068 1 iwlcore
led_class 6408 1 iwlcore
mac80211 182184 2 iwlagn,iwlcore
cfg80211 29840 3 iwlagn,iwlcore,mac80211
Am I missing something obvious? The kernel is current as of today, which would make it kernel26 2.6.27.10-1.
Thanks for your help,
Chris

I'm getting this same error with the latest kernel
Linux koi 2.6.33-ARCH #1 SMP PREEMPT Mon Apr 26 20:00:20 CEST 2010 i686 Intel(R) Core(TM)2 Duo CPU T7250 @ 2.00GHz GenuineIntel GNU/Linux
~ % lspci
0c:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 2.6.33-ARCH-ks
iwlagn: Copyright(c) 2003-2009 Intel Corporation
iwlagn 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
iwlagn 0000:0c:00.0: setting latency timer to 64
iwlagn 0000:0c:00.0: Detected Intel Wireless WiFi Link 5100AGN REV=0x50
iwlagn 0000:0c:00.0: Unsupported (too old) EEPROM VER=0x114 < 0x11a CALIB=0x1 < 0x4
iwlagn 0000:0c:00.0: PCI INT A disabled
iwlagn: probe of 0000:0c:00.0 failed with error -22
~ % rfkill list
0: dell-wifi: Wireless LAN
Soft blocked: no
Hard blocked: no
1: dell-bluetooth: Bluetooth
Soft blocked: no
Hard blocked: no
2: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
The iwlagn is loaded. and this is 32bit arch
Last edited by el mariachi (2010-04-29 20:28:59)

Error Code 10 with GPIB PCI Card

PC used: Dell optiplex GX110, lastest Bios release, Windows 2000 SP4, GPIB Drivers version 2.2, Local Admin session.
After having install the driver (without the GPIB)and plug the card, this one is automaticaly recognised by the Os.
But, after the reboot (asked by the OS to validate the installation), the GPIB card appears, in the device manager, with an error code 10 (not started)....
I tried with two (new) differents GPIB PCI Card, two OS (First time with NT4.0 SP6 Drivers 1.7 and now, Win2000 SP4 Drivers 2.2) and with two PCs Dell Optiplex GX110 !
I even tried with a "Ghost" from an other PC (also an Optiplex GX110, with the same model of GPIB Card)
-> I obtain the same error each time !
Help me please..........

Hello,
Could you give me the exact reference of the board (PCI-GPIB, PCI-GPIB+, AT-GPIB, AT/GPIB-TNT...)?
Is the error code displayed on the Windows device manager (in the properties dialog box of the device)?
What is the exact description of the error code?
A PCI-GPIB installation do not need to reboot the OS if the NI-488.2 driver is correctly installed. The board should be recognized in MAX and you must be able to scan for instruments and start I/O communication with the device from test panels in MAX.
Update me as soon as you receive another feedback.
Regards.

WLC 5508 : WPA2 enabled SSID - especially Intel & Dell wireless cards are not getting connected

Hi ,
I have one pecular issue in my wireless lan set-up. I have some laptop users who are using below inbuilt wireless adapter/cards :
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
1 ) Dell wireless 1397 WLAN Minicard
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
2 ) Intel Centrino Advanced N6200 AGN
above card are having issue with WPA2 enabled ssid connecitivity. strange is , the same users are getting connected to other wep enabled SSID but its not working for WPA2 SSID.
I have external ACS server which is used for radius authentication. Last time I had put same query in support forum did some workaround.
eq. disabling DHCP proxy option in WLC and moving all DHCP scope in external server.
After doing this workaround this mentioned users are still facing issue. I gone through some cisco document and some forums and came across that there is something to be done in " Session Timed Out " optionin WLC
which is default 1800 sec based on that I tried to capture debug outputs for mentioned above problematic clients and user who is working fine .
I gone through the same debug output and observed :
User who is working fine :
Processing Access-Accept for mobile 00:22:5f:8d:55:84
00:xx:xx:xx:xx:xx Setting re-auth timeout to 1800 seconds, got from WLAN config.
00:xx:xx:xx:xx:xx Station 00:22:5f:8d:55:84 setting dot1x reauth timeout = 1800
00:xx:xx:xx:xx:xx Creating a PKC PMKID Cache entry for station 00:22:5f:8d:55:84 (RSN 2)
00:xx:xx:xx:xx:xx Adding BSSID 00:1f:ca:2c:f3:01 to PMKID cache for station 00:22:5f:8d:55:84
New PMKID: (16)
The User / card which is having issue :
Processing Access-Accept for mobile 00:22:5f:90:a2:ac
00:xx:xx:xx:xx:xx Setting re-auth timeout to 0 seconds, got from WLAN config.
00:xx:xx:xx:xx:xx Station 00:22:5f:90:a2:ac setting dot1x reauth timeout = 0
00:xx:xx:xx:xx:xx Stopping reauth timeout for 00:22:5f:90:a2:ac
00:xx:xx:xx:xx:xx Creating a PKC PMKID Cache entry for station 00:22:5f:90:a2:ac (RSN 2)
00:xx:xx:xx:xx:xx Adding BSSID 00:26:cb:1d:fe:31 to PMKID cache for station 00:22:5f:90:a2:ac
New PMKID: (16)
Please suggest me to do workaround.

Hi,
According to output of working as well as not working wireless cards ,
below is my observations :
Not working wireless cards observation :
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin-top:0cm;
mso-para-margin-right:0cm;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0cm;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
The client passed the L2 authentication and that, after successful association, it is now going into the DHCP_REQD state
Not-working wirelss card :
*Apr 06 11:58:15.866: 0c:60:76:3e:8c:49 10.10.232.137 RUN (20) Successfully plumbed mobile rule (ACL ID 255)
*Apr 06 11:58:15.866: 0c:60:76:3e:8c:49 Stopping retransmission timer for mobile 0c:60:76:3e:8c:49
*Apr 06 11:58:15.869: 0c:60:76:3e:8c:49 10.10.232.137 Added NPU entry of type 1, dtlFlags 0x0
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin-top:0cm;
mso-para-margin-right:0cm;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0cm;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
The client entry is added to the Network Processing Unit (NPU) of the controller with an IP address of 10.10.232.137 but after that , I am getting below output
*Apr 06 11:58:22.742: 0c:60:76:3e:8c:49 Copy AP LOCP - mode:0 slotId:0, apMac 0x0:1f:ca:2c:ea:e0
*Apr 06 11:58:22.742: 0c:60:76:3e:8c:49 Copy WLAN LOCP EssIndex:2 aid:50 ssid:USTRI_SECURE
*Apr 06 11:58:22.742: 0c:60:76:3e:8c:49 Copy Security LOCP ecypher:0x0 ptype:0x2, p:0x0, eaptype:0x2 w:0x1 aalg:0x0, PMState:        RUN
*Apr 06 11:58:22.742: 0c:60:76:3e:8c:49 Copy 802.11 LOCP a:0x0 b:0x0 c:0x0 d:0x0 e:0x1 protocol2:0x3 statuscode 0, reasoncode 99, status 3
*Apr 06 11:58:22.742: 0c:60:76:3e:8c:49 Copy Username LOCP :   U25744
*Apr 06 11:58:22.743: 0c:60:76:3e:8c:49 Copy IP LOCP: 0xa0ae889
*Apr 06 11:58:22.743: 0c:60:76:3e:8c:49 Copy CCX LOCP 4
*Apr 06 11:58:22.743: 0c:60:76:3e:8c:49 Copy MobilityData LOCP status:1, anchorip:0x0
*Apr 06 11:59:14.002: 0c:60:76:3e:8c:49 10.10.232.137 RUN (20) State Update from Mobility-Complete to Mobility-Incomplete
*Apr 06 11:59:14.002: 0c:60:76:3e:8c:49 Clearing Address 10.10.232.137 on mobile
*Apr 06 11:59:14.002: 0c:60:76:3e:8c:49 10.10.232.137 RUN (20) Change state to DHCP_REQD (7) last state RUN (20)
*Apr 06 11:59:14.002: 0c:60:76:3e:8c:49 apfMmProcessDeleteMobile (apf_mm.c:522) Expiring Mobile!
*Apr 06 11:59:14.002: 0c:60:76:3e:8c:49 apfMsExpireMobileStation (apf_ms.c:4427) Changing state for mobile 0c:60:76:3e:8c:49 on AP 00:1f:ca:2c:ea:e0 from Associated to Disassociated.
working cards ouput :
*Apr 06 12:16:28.038: 00:22:5f:8d:55:84 10.10.232.190 RUN (20) Successfully plumbed mobile rule (ACL ID 255)
*Apr 06 12:16:28.038: 00:22:5f:8d:55:84 Stopping retransmission timer for mobile 00:22:5f:8d:55:84
*Apr 06 12:16:28.042: 00:22:5f:8d:55:84 10.10.232.190 Added NPU entry of type 1, dtlFlags 0x0
The client entry is added to the Network Processing Unit (NPU) of the controller with an IP address of 10.10.232.190 and as expected , I am getting below output
*Apr 06 12:16:28.749: 00:22:5f:8d:55:84 DHCP received op BOOTREQUEST (1) (len 321, port 29, encap 0xec03)
*Apr 06 12:16:28.751: 00:22:5f:8d:55:84 DHCP processing DHCP REQUEST (3)
*Apr 06 12:16:28.751: 00:22:5f:8d:55:84 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
*Apr 06 12:16:28.752: 00:22:5f:8d:55:84 DHCP   xid: 0x6eefbbb8 (1861204920), secs: 0, flags: 0
*Apr 06 12:16:28.752: 00:22:5f:8d:55:84 DHCP   chaddr: 00:22:5f:8d:55:84
*Apr 06 12:16:28.752: 00:22:5f:8d:55:84 DHCP   ciaddr: 10.10.232.190, yiaddr: 0.0.0.0
*Apr 06 12:16:28.752: 00:22:5f:8d:55:84 DHCP   siaddr: 0.0.0.0, giaddr: 0.0.0.0
*Apr 06 12:16:28.753: 00:22:5f:8d:55:84 DHCP successfully bridged packet to DS
*Apr 06 12:16:30.751: 00:22:5f:8d:55:84 Copy AP LOCP - mode:0 slotId:0, apMac 0x0:1f:ca:2c:f3:0
*Apr 06 12:16:30.751: 00:22:5f:8d:55:84 Copy WLAN LOCP EssIndex:2 aid:10 ssid:USTRI_SECURE
*Apr 06 12:16:30.751: 00:22:5f:8d:55:84 Copy Security LOCP ecypher:0x0 ptype:0x2, p:0x0, eaptype:0x2 w:0x1 aalg:0x0, PMState:        RUN
*Apr 06 12:16:30.752: 00:22:5f:8d:55:84 Copy 802.11 LOCP a:0x0 b:0x0 c:0x0 d:0x0 e:0x1 protocol2:0x3 statuscode 0, reasoncode 99, status 3
*Apr 06 12:16:30.752: 00:22:5f:8d:55:84 Copy Username LOCP : USTR\U17967
*Apr 06 12:16:30.752: 00:22:5f:8d:55:84 Copy IP LOCP: 0xa0ae8be
*Apr 06 12:16:30.752: 00:22:5f:8d:55:84 Copy CCX LOCP 4
*Apr 06 12:16:30.752: 00:22:5f:8d:55:84 Copy MobilityData LOCP status:1, anchorip:0x0
Finally client is getting stuck with DHCP-REQD state ..................
Please look into this and put light on this ............

Error code 10 for Intel 5300 Wireless Card

Similar Messages

Maybe you are looking for