Error: DAQ-STC Counter functions missing from library

Using LabView 6.1, NI-DAQ 6.6.1 for MacOS on a laptop.
DAQ Hardware: DAQCard 16E-4.
When trying to use the advanced counter functions (for DAQ-STC type counters), LabVIEW generates an error saying that it can't find the function in the library. The code interface nodes for the VIs don't seem to be attached to anything. I've installed the latest version of DAQ Drivers for Mac; am I missing something here? Any insight into this problem would be appreciated.
Regards,
jdk

Hi jdk,
I think it could be just an installation issue. I assume that you are using Mac 9.1. I've run LV 6.1 with NIDAQ 6.6.1 on Mac 9.1 and it works just fine, including DAQ-STC counter functions.
If LabVIEW 6.1 was installed without DAQ support, run the LabVIEW 6.1 installer and perform a custom installation for DAQ support. Then, run
the NI-DAQ 6.6.1 installer to upgrade NI-DAQ.
Hope this helps.
Regards,
Pravin Borade
Applications Engineer, National Instruments

Similar Messages

Files missing from library after archive and install

Hi forum folk
any help you could give would be much appreciated.
I can't seem to verify my permissions on HD. I have run disk utility both from finder and from my OSX startup disk and consistently get the error message "Disk Utility has lost its connection with the Disk Management Tool and cannot continue." I then reinstalled the operating system all together making sure to archive and install as well as archive previous network and preference settings. This means I am running 10.3.4 at the moment (and I can't verify any of the software updates at the moment). After reinstalling I still cannot verify my permissions, so now I am trying to back up all my files so that I can reinstall the OSX again, erase everything, and start from scratch. But I'm running into some very strange problems while doing this. select files are missing from ~/library. there is no Safari file, for example. I tried looking in HD/previous systems/library where my library files were saved before I reinstalled the operating system but there is no such folder in there either. this means all of my bookmarks are gone. additionally, under library/preferences (in both the old and new library folders) there is no file named com.apple.itunes.plst. so all of my itunes playlists are gone as well. these are the only missing files I have found thus far and i can't explain why they selectively would not have been saved after the archive and install. Everything else seems to be intact. Any ideas?
thanks
jb
powerbookG4 Mac OS X (10.3.9) running 10.3.4 at the moment - can't verify permissions on 10.3.9

jbeep:
my HD has a capacity of 8.85 GB available. When I reinstalled panther I had little more than 3 GB available (I deleted a bunch of unneeded things since then)
Thanks for this update. What is the total formatted capacity of your HDD? I ask because I suspected that you might be cutting it pretty close. The rule of thumb is that you should have 10-15% of your total capacity available as free space. My personal rule is 15%-20%. This allows for more efficient perfomrance of OS X.
I am in the process of backing up everything on my seagate combo USB 2.0/firewire 200 GB external (I am using the firewire cord)
Having an up-to-date backup is one of the primary rules, often observed more in the breach than not. Since you have an HDD that supports Firewire, I suggest that you make a bootable clone of your entire HDD using SuperDuper. You can then use this backup as an emergency boot drive. However, it must be Firewire, as PPC Macs don't boot from USB devices.
I also have heard that it is advisable to reinstall the OS "every now and again" and I hadn't done this for at least two years. was I ill-advised?
Most experienced Mac users never re-install, except under dire circumstances. Since installing my new HDD in this computer I have never re-installed. Re-installation is the utlimate intrusive measure, and it exposes one to all kinds of issues, from lost data, to flawed installaton, to installations that fail midstream. Re-installation is not an effective maintenace procedure. Here are some helpful links in terms of maintenance:
Mac OS X 10.3/10.4: System maintenance
Macintosh OS X Routine Maintenance
Maintaining OS X.
I'm going to restart now and try and verify my permissions again using the procedure on the above link. I'll let you know what happens.
Instead of verifying permissions, just go ahead and Repair Disk Permissions. Verifying permissions does nothing, and wastes your time, as it is difficult to tell whether you need to repair, and you have to repair anyway.
Do post back with an update of your progress and any further questions or comments.
Good luck.
cornelius
Message was edited by: cornelius

HT201210 Itunes will no longer open with the error message MSVCR80.dII is missing from the computer, and I'm advised to reinstall itunes but that hasn't worked. What else can I try?

Itunes will no longer open with the error message MSVCR80.dII is missing from the computer, and I'm advised to reinstall itunes but that hasn't worked. What else can I try?
Thanks for your help
Pippa

Click here and follow the instructions.
(98708)

I can no longer access my itunes. Receive error message "MSVCR80.dll is missing from your computer....must reinstall" ????

I can no longer access my itunes on desk top computer. Receive error message "MSVCR80.dll is missing from your computer....must reinstall" ???? Solutions? Cause?

See Troubleshooting issues with iTunes for Windows updates.
tt2

HT2731 Can not open Itunes on my computer,i get error msg MSVCR80.dill is missing from your computer . What do i do?

Can not open itunes on my computer,I get error msg MSVCR80.dill is missing from your machine. What do I do?

Work through the user tip: https://discussions.apple.com/docs/DOC-6562

Error creating index (trailing null missing from STR bind value)

I'm having the following error:
ERROR at line 1:
ORA-29855: error occurred in the execution of ODCIINDEXCREATE routine
ORA-20000: interMedia Text error:
DRG-50857: oracle error in dreii0fsh
ORA-01480: trailing null missing from STR bind value
ORA-06512: at "CTXSYS.DRUE", line 157
ORA-06512: at "CTXSYS.TEXTINDEXMETHODS", line 176
ORA-06512: at line 1
my script is:
create index IDX_XML on EN_TESTE_XML(TXT_XML_CURRICULO)
indextype is ctxsys.context;
My Oracle is 9.0.1
TXT_XML_CURRICULO -> XMLTYPE then
the section group is PATH_SECTION_GROUP by default.
thanks.
Marlon

If you get an OCI error when simply updating a record in PL/SQL Developer, it sounds like a PL/SQL Developer issue, although not one I've come across. You might try Allround Automations tech support. They'll need your exact versions of Oracle server, Oracle client and PL/SQL Developer.
SQL*Plus is part of the Oracle Client software so you should have it somewhere, or you can download it free.

Reinserting Preview/Images missing from Library and Project

After ingesting my images from CF reader into a project, I started working on them. For some reason after working on them for awhile, I started noticing that previews were missing from the project. I looked in the Library and they were not there either. However, when I looked in to the project folder (via the Aperture "folder" in Finder), the images and associated Aperture information files were all there in their respective folders.
I'm not sure how I lost/deleted so many images from my folder and Library (I may have accidently deleted a stack, but when I searched the number of images missing I know I could not have accidently deleted that many that way if I did). But since the files are still on my hard drive in their respective folders, in the right location, is there a way to bring them back into Aperture?
Thanks,
Ed

bump...if anyone can tell me that would be great. I know it sounds like a dumb question, but for the life of me I cannot do any command - import, etc. - that can get these files that reside in the actual folder to show up in Aperture's Library or its original project.
Thx,
Ed

Songs on my iphone are missing from library, how do I load them back in?

I noticed when I was about to back up my iphone that some of the songs on my phone are missing from my library. They appear not to be on my Windows based computer either. Can I "push" or create a new library for the songs on my iphone?
Thanks for any help you can provide

See Empty/corrupt iTunes library after upgrade/crash or
Recover your iTunes library from your iPod or iOS device.
tt2

Error Customizing for feedback functionality missing

Hi
We have Configured Service Desk in our Solution Manager and we are able to Send messages in Solution Manager Box.
When we are trying to send from External Box i am getting an Warning "Customizing for feedback functionality missing"
RFC between Solman to ERP system Configured and Working
Could any one please tell me i need to do any other config
Question number 2.
we have 11000 users when we configure Service Desk do we need to create 11000 USerd id in Solman?
Points will be rewarded

Hi,
When creating a support message from a satellite. Solution Manager first creates an ABA Notification.
Check your ABA Notification SLF1settings in tcode DNO_CUST01 (number range, action profile).
Regards,
Remy Piets

Illustrator CC2014 Error message "Alcid.dll is missing from your computer. etc."

I have been experiencing a problem with Illustrator CC2014. This occurs after I get out of Illustrator and then attempt to open the software up the next morning. I get the following message; "The program can't start because Alcid.dll is missing from your computer. Try reinstalling the program to fix the problem." Uninstalling and reinstalling fixes the problem initially but then it reoccurs every time I restart the computer.

You have a permissions problem and your changes to your computer don't stick or Windows System Restore is interfering. Impossible to tell without more info.
Mylenium

Apps missing from Library sidebar after 10.1 update

Installed 10.1 yesterday and ever since the apps selection from the library is missing.
I experienced problems installing 10.1 yesterday, would not run via the update selection from within iTunes.
Instead, I manually downloaded and ran each component separately.
That was when I first noticed the problem.
I have completely uninstalled iTunes and all related programs.
Re-installed iTunes 10.1, no change.
I have reverted to a previous library file, no change.
All the apps still exist in the iTunes/MobileApplication folder.
Any ideas?

Sorted. In Edit/Preferences, General tab, Sources, the "Apps" checkbox was unselected. Lots of options there now - is this new?
Not sure why it got unselected...

Aperture 3.5 projects: Some are missing from Library listing

I use Aperture 3.5.1 with OS 10.9.2, and I have studied the various pages of Aperture manuals, and read quite a few Questions, and I think I understand the difference between projects and albums and between managed and referenced files. But I am puzzled about a few project locations.
To the left of the Aperture display window is a vertical pane about 2 inches wide, with tabs labeled "Library, Info, Adjustments."
In that left-hand pane of the window, under the tab “Library” is a heading “APERETURE LIBRARY-MASTER” and under that is the icon of “Projects”. When I select this, the right hand portion of the full window shows thumbnails representing of all my projects. These are organized by year and for each year, by date. This is the organization that Aperture did when I imported the photos, mostly from cameras. Fine.
In that left hand pan, under the Library tab, further down, there is a heading “PROJECTS”. It shows a list of folders and albums and projects.
I see that in this library there are folders marked 2011 and 2012. In each of those there are folders for the months. In 2012 these include “May”, “Jun UK", "Jun US", “Jul" and others. When I select any of these the associated thumbnails are all visible in the main display window to the right.
In the 2012 > Jun UK folder are 5 projects, with dated names such as "Jun 06, 2012 Chicheley". The word “Chicheley” and “UK" I added, but the rest of the structure 2012 > Jun was created by Aperture when I imported the photos.
However, and here is what puzzles me. In the thumbnail display to the right, of several hundred projects, there are 15 contiguous projects, all from June 2012, that are not listed in the library panel of projects in the Library tab pane at the left.
I can look at the “info” tab and see what the “Project Path” is for any photo. To judge by the badges, All of my photos are managed, not referenced. Indeed, I cannot find any photos in my Aperture library that are referenced.
The projects that show up in the Library listing at the left pane have Project paths that start with a year, for example
2012 > Jun UK > Jun 06, 2012
The projects that do not show up in the Library listing have names such as
Jun UK Chicheley > Jun 05, 2012 Aston
At the top of the Library pane is a search box. It finds Jun 06 but not Jun 05.
I have looked inside the Aperture Library package and I see the organization there for the projects that show up in the library listing. But that is missing the days that are not in the listing — it is missing the projects that show up in the main window but not in the Library list..
Those thumbnailed of the missing projects are of photos that are not referenced, I have used the main menu at the top of the screen to check that.
I can edit all the photos, wherever they may be. No problem. But why do all the projects not show up in the library listing? Where are they?
I have used EasyFind to search for a folder “Jun UK Chicheley”, allowing search in packages, but did not find it. Same problem with any of the other 15 projects that show up in PROJECTS on the right, but not in the Library listing on the left.
I may have imported the missing projects not from the camera but from a travel Aperture library, using the import library option.
Maybe I should select all of these photos and then do a “Consolidate”. I have read about this, in the Manual and in the Suppport questions, but it is not clear whether that will do what I want. I see that Consolidate is something I can do for any of my photos, not just for those that are not shown in the library. So what happens with Consolidate of a photo that is already in the listing of projects? Should I choose “copy” or “move”? If I choose “move” then what happens to whatever collection these came from?
“Show in Project” and “Show in Finder” seem to be unavailable for all of my photos.
I will appreciate help.

What you're seeing when you try to view the original file is the warning that iPhoto had broken the file path/link to the orignal file. Try this: make a temporary, backup copy of your library if you don't already have one (Control-click on the library and select Duplicate from the contextual menu) and apply the two fixes below in order as needed:
Fix #1
Launch iPhoto with the Command+Option keys held down and rebuild the library.
Since only one option can be run at a time start with Option #1, followed by #3 and then #4 as needed.
Fix #2
Using iPhoto Library Manager to Rebuild Your iPhoto Library
Download iPhoto Library Manager and launch.
Click on the Add Library button, navigate to your Home/Pictures folder and select your iPhoto Library folder.
Now that the library is listed in the left hand pane of iPLM, click on your library and go to the File ➙ Rebuild Library menu option
In the next window name the new library and select the location you want it to be placed.
Click on the Create button.
Note: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments but not books, calendars or slideshows. The original library will be left untouched for further attempts at fixing the problem or in case the rebuilt library is not satisfactory.
OT

Error when calling webutil functions in a library.

I have installed and configured webutil on my Linux machine and I can successfully run the webutil_demo.
I have a form with webutil library attached and object group added calling webutil_file.File_save_dialog successfully.
But when I want another form to a procedure in a PL/SQL library (pll_window.pll ) which call webutil_file_transfer.as_to_client,, It reports an error saying
The WEBUTIL object group is not available in this Form. WebUtil cannot work
and pop out a small alert "Please acknowledge"
When I click OK, it says FRM_40734: Internal Error: PL/SQL error occurred
So what might be the problem ? I had webutil.pll attached to my library file pll_window.pll also.

frank1018 wrote:
I have installed and configured webutil on my Linux machine and I can successfully run the webutil_demo.
I have a form with webutil library attached and object group added calling webutil_file.File_save_dialog successfully.
But when I want another form to a procedure in a PL/SQL library (pll_window.pll ) which call webutil_file_transfer.as_to_client,, It reports an error saying
The WEBUTIL object group is not available in this Form. WebUtil cannot work
and pop out a small alert "Please acknowledge"
When I click OK, it says FRM_40734: Internal Error: PL/SQL error occurred
So what might be the problem ? I had webutil.pll attached to my library file pll_window.pll also.Do you subclass from webutil.olb to your form ?
Hope this helps

Error Code 150:30 - Photos Missing From My Catalog and LR Can't Load Them

LightRoom 5.5 stopped functioning and cannot find the catalogs or files I was using for the last several days. I receive Error Code 150:30 and am advised to contact Adobe Support, though I can't seem to find a direct link to do so. Is the issue possibly related to licensing issues? I purchased a copy of LR 5 from B&H and later received two licenses through purchases of Leica cameras. I am trying to get myself setup on LR, but seem to be locked out until I can reestablish the links to my photo files which seem to be grayed out. Thanks for any help or guidance. Robert

See if anything here helps;
http://helpx.adobe.com/creative-suite/kb/error-licensing-stopped-windows.html

Imported Music is missing from library

I've recently started having problems seeing imported music in my iTunes library.
I put a CD into my computer, and the CD is visible within iTunes in the devices Tab, as normal. I import the CD, and can watch the tracks as they are added to my computer (in the devices tab). However, after the import is completed, the tracks are not visible in the Library:Music window. The files are there on my hard drive (I can see the .m4a files in Music-->iTunes-->iTunes Music), and the folders are appropriately named by artist, but after I eject the CD I can't find them within iTunes. All of my old music is there, just not the new stuff.
I've tried moving the file of the music from the iTunes folder onto my desktop, and then adding it back into iTunes. I get the window saying the files are being copied into my iTunes library, and they go back into the iTunes folder, but I still can't see them from within iTunes. I can even drag and drop the files onto my iPod within the Devices tab within iTunes, and add the music to my iPod that way, but I don't know why I can't see the tracks in my Library:Music.
This has only become a problem within the last week, but I don't think I've changed any preferences that would cause this problem.
Any and all suggestions would be greatly appreciated. Thanks!

I'm having the same problem, it started like 2 days ago! Songs that I imported from burned CD's a few years ago are suddenly not available on iTunes because iTunes can't find them. And I can't remember their file paths either, so that's a bit of an issue...
A few songs that I downloaded from random sites are also missing...is this a temporary iTunes bug?

Error: DAQ-STC Counter functions missing from library

Similar Messages

Maybe you are looking for