Error message from a thermotron set temp VI

Hello,
   I am getting the following error code from the Load temp vi for a Thermotron temp chamber -1073807339. Does anyone know how to figure out what this error means? I am am to succesfully initalize the temp chamber, but when I try to set the chamber temp and get errors.
Regards,
Kaspar

Hi Kaspar,
You are correct, rrror 1073807339 refers to a timeout error. A timeout on the read is usually caused by sending an incorrect command. The instrument may not recognize the command and does not generate a response.
I know this may be a silly question, but here goes:  How do you communicate to the chamber? ( eg: serial port - most likely)
Since it is likely serial, here is some info.
You can set the timeout by running the VISA Configure serial settings VI from the Instrument Control>>Serial palette. However, the default timeout is 10 seconds.  But without seing your application, it is difficult to give proper advice.
It could be a simple matter of setting the correct parameters.  If serial, are you able to "talk to it" using somthing like HyperTerminal?  If so, duplicate the settings.  Also, try opening the Example Finder (Help>>Find Examples) and searching for "Serial".
As for a solution - A timeout occures when the time passed and you don't get the number of bytes you asked for. How many bytes are you asking for? You can use the Bytes at Serial Port property node to determine how many bytes are waiting and wire that into the Read VI.
Hopefully this is a start.. or it helped..
RayR

Similar Messages

  • Error Message "Delete price or set "Invoice Expected Indicator" in PO.

    Hi Gurus,
    We are in extended classic scenario with version 5.0.
    We are getting error message "Delete price or set "Invoice Expected Indicator" when we are releasing the PO from Release PO option.
    We are getting this error message in below situation:
    We created shopping carts without vendor then after approval PO gets created in "Held status". When we edit the PO & add vendor then system gives error message "Delete price or set "Invoice Expected Indicator" (Line 1).
    In this case the invoice expected indicator is not sets when we add vendor in the PO but if we create Shopping cart with vendor & when PO create din that case the invoice expected indicator is automatialy comes.
    Can any one please help me to resolve this issue.
    Thanks & Regards,
    Manish
    Edited by: Manish Mamidwar on Jul 30, 2010 5:40 PM

    Hi All,
    I have the same problem, Delete price or set "Invoice Expected Indicator" in PO
    I have an Item Position of the PO that is Limit of Liability and for this position type I will not make invoice, then I would like remove the flag of invoice execution, but a recived your same message, can you tell me how did you resolve this problem?
    Kind regards
    Valentina Mari
    Edited by: Fuffo Fuffi on Nov 10, 2010 12:51 PM

  • A way to display error messages from the program

    Dear all,
    I am looking forward to display a set of error messages(in a internal table) during the execution of the program to the user.
    I wanted to know the better way of displaying error messages from my program with more options.
    Well I tried out using displaying errors as ALV list/Grid or as simple list processing.
    But I found some  stanadard transactions (Like in MM and FI  where errors are shown in a better way, but failed to find out how they are done.
    Please guide me.
    Thanks in advance
    Aryan

    Try to use application logging it has a very good way to display a set of messages.
    [http://abap4.tripod.com/Using_Application_Logging.html|http://abap4.tripod.com/Using_Application_Logging.html]
    Run this report in se38 an example sap report to understand logging way to show a set of messages
    Report Name  :  SBAL_DEMO_01
    Edited by: Vighneswaran CE on Dec 19, 2010 3:01 PM
    Edited by: Vighneswaran CE on Dec 19, 2010 3:11 PM

  • Java - Axis2: How to get an error code / error message from the Javascript via SOAP

    Hi
    In our Java applicsation we call a Javascript in a Indesign CS Server using the following code:
    --- SNIP BEGIN ---
    // calls the remote service on the indesign server
    try {
    // create service
    ServiceStub oIndsgnSrvStub = new
    ServiceStub(sIndesignServer);
    // create service parameter
    ServiceStub.RunScriptParameters
    oIndsgnSrvRSParams = new ServiceStub.RunScriptParameters();
    // create arguments with source- and target-file for parameter
    ServiceStub.IDSPScriptArg[] oIndsgnSrvSArgs = new ServiceStub.IDSPScriptArg[2];
    oIndsgnSrvSArgs[0] = new
    ServiceStub.IDSPScriptArg();
    oIndsgnSrvSArgs[0].setName("xml-input");
    oIndsgnSrvSArgs[0].setValue(sSourceFile);
    oIndsgnSrvSArgs[1] = new
    ServiceStub.IDSPScriptArg();
    oIndsgnSrvSArgs[1].setName("output-file");
    oIndsgnSrvSArgs[1].setValue(sTargetFile);
    // define service parameter
    oIndsgnSrvRSParams.setScriptArgs(oIndsgnSrvSArgs);
    oIndsgnSrvRSParams.setScriptFile(sScriptFile);
    oIndsgnSrvRSParams.setScriptLanguage("javascript");
    oIndsgnSrvRSParams.setScriptText("");
    // create runscript
    ServiceStub.RunScript oIndsgnSrvRS = new ServiceStub.RunScript();
    // set parameter
    oIndsgnSrvRS.setRunScriptParameters(oIndsgnSrvRSParams);
    //$$$ there should be an answer returned by the InddSrvr
    // execute SOAP call
    ServiceStub.RunScriptResult oIndsgnSrvRes = oIndsgnSrvStub.RunScript(oIndsgnSrvRS);
    if(oIndsgnSrvRes.getErrorNumber() == 0) {
    oServerProdJob.setProdState(CBP_Constant.REMOTEPRODUCTIONSTATE_SUCCESS);
    bOK = true;
    } else {
    oServerProdJob.setProdState(CBP_Constant.REMOTEPRODUCTIONSTATE_FAILURE);
    bOK = false;
    //$$$ should be set, if there is something returned by inddsrvr
    //oServerProdJob.setErrorMsg(sErrorMsg);
    } catch(Exception e) {
    sError += e.getMessage() + "\n";
    bOK = false;
    --- SNIP END -----
    The problem is that we don't get the error code and/or the error message from the Javascript in oIndsgnSrvRes. The error code is always 0 if I set an Integer value as return in the Javascript. If I set a String, there is an Exception in the Java application.
    Here is the Java script we use:
    --- SNIP BEGIN ---
    main();
    main()
    var sError = "";
    var sXMLInput = "";
    var sLayoutPath = "";
    // get the SDKCodeSnippetRunner object
    var cbpAdapter = app.cbpCbpadapterObject
    if (cbpAdapter) {
    sXMLInput=app.scriptArgs.get("xml-input");
    sLayoutOutputFile=app.scriptArgs.get("output-file");
    sError = cbpAdapter.doProcess(sXMLInput, sLayoutOutputFile);
    return sError; // This give an Exception; if I return an Integer the ScriptResult is always 0
    --- SNIP END -----
    If I try this with the test application from Adobe I get the error code correctly. But in the Java application, using SOAP, I can't get the error code.
    What could be wrong?
    Any ideas?
    Thanks a lot for the support.
    Kind regards
    Hans

    user11340104 wrote:
    Hello -
    i am calling sqlplus from a bash shell script. If the sql statement generates an error, how can I return that error code (unsuccessful) back to the bash shell?
    Well, let google be your friend,
    http://www.google.co.in/search?rlz=1C1GGLS_enIN327IN327&sourceid=chrome&ie=UTF-8&q=sqlplus+error+codes
    There are many threads I guess talking about the same issue.
    HTH
    Aman....

  • 'Cannot obtain error message from server' when trying to use ODBC

    Post Author: Grant C
    CA Forum: Data Connectivity and SQL
    Hi, I'm developing some reports using Crystal XI on my local PC, using an Oracle 10i back end on a separate server.  The SQL for the report is in a method in an oracle package.
    When I set the datasource location, selecting 'Oracle Server' then entering the details works fine, and the report runs.  However, when I try to use an ODBC connection I get the following error:
    Database Connection Error: 'Cannot obtain error message from server.'
    The ODBC link is set up as a System DSN, which works fine when I test it.  I think I need to use ODBC as some of the reports (which I inherited) seem to fail when run on the Crystal Server, and it seeme to be the ones set up with ODBC which work.
    Any thoughts?  Thanks.

    Hi Mars-
    It sounds like your NI-DAQ installation may have become corrupted. I would suggest uninstalling and reinstalling the DAQmx 7.4 driver to correct this problem and ensure that you're up to date. This download is available here: NI-DAQ 7.4
    If the problem persists you may want to uninstall and reinstall LabVIEW and then NI-DAQ in that order. The error message will usually give an indication as to which VI the error occurred in. Please let us know which VI is failing if you're unable to avoid the error with these suggestions.
    Have a good day-
    Tom W
    National Instruments

  • Every time I sign into my Macbook, I get an error message from Automator; "The data couldn't be read because it has been corrupted.". I have never created an Automator workflow. How do I find out what Automator is trying to run and stop it?

    Every time I sign into my Macbook, I get an error message from Automator; "The data couldn't be read because it has been corrupted.". I have never created an Automator workflow. How do I find out what Automator is trying to run and stop it?

    Maybe it's set as a login item:
    - System Preferences: Users and Groups:
    - Highlight your user account in the left pane/list
    - Click "Login" tab at the top.
    See if you have an Automater action on the list
    - Note, you can select it, then right-click, and can then select "Reveal in Finder". That way you might have an idea what installed it.

  • Database Connection Error: Cannot obtain error message from the server

    I have a SQL statement that wants to add a temp table to the database.   The SQL statement works fine but when I try to add it via 'Add Command' feature in Crystal XI R2, I get the following error message:
    Database Connection Error: Cannot obtain error message from the server
    Any ideas?
    Thanks in advance,
    Zack H.

    Hi Raghavendra,
    I am using this in the 'Add Command' feature but I get the error message displayed in the subject line:
    CREATE TABLE #TibetanYaks(
    YakID char(4),
    YakName char(20) )
    INSERT INTO #TibetanYaks (YakID, YakName)
    SELECT  LastName, FirstName
    FROM      Employee
    WHERE      EmployeeID between '2000' and '3000'
    I haven't tried to add this as a stored procedure but I imagine it will work as I have no problems yet with stored procedures.  I simply want to be able to use temporary tables for the sole purpose of that session and not creating anything static in the database.
    By the way, even though I get the error message, when I look on the backend database, I see that the temporary table was successfully created...its just not brought across correctly in Crystal.
    Any ideas?
    Zack H.

  • IPhone error message from iPad

    In the middle of syncing my iPad (3G) this week it hung, and I had to shut the computer down as it froze too.
    Since then, I cannot use the 3G connection when I'm away from my wi-fi; Settings does not work (I can open it, tap General, tap Wi-Fi then it freezes); and I get an iPhone error message from iTunes when I connect my iPad(!) to my Powerbook (OS 10.6.7, iTunes 10.3.1). And iTunes sometimes recognizes the iPad as a Device, but often does not.
    I do have an iPhone 4 connected but it works fine.
    The iPad connection error message is:
    Any clues?
    BeemOs

    Did you set up Gmail as a mailbox in the Mail App on your iPad?

  • Suppress Flash Player Error Messages from Browser?

    I'm well aware of try catch functions, but in general is
    there a simple setting to suppress browsers from displaying
    stackTraces on errors?

    I have searched through every book, forum, and found nothing
    on suppressing Flash Player error messages from the browser. If
    it's really not possible, this is terrible news. It's nice to think
    that we'd encapsulate everything in try catch methods, but come
    on....

  • When I use the shortcut to open a new window in safari (command N), I get a 404 error message from Google. How do I change where 'Command N' routes to?

    When I use the shortcut to open a new window in safari (command N) on my Macbook Pro, I get a 404 error message from Google. How do I change where 'Command N' routes to? 

    It's not necessary to change the Command N keystroke..
    From your Safari menu bar click Safari > Preferences then select the Privacy tab.
    Click:   Remove All Website Data
    Then delete the cache.
    Open a Finder window. From the Finder menu bar click Go > Go to Folder
    Type or copy paste the following
    ~/Library/Caches/com.apple.Safari/Cache.db
    Click Go then move the Cache.db file to the Trash.
    Quit and relaunch Safari to test.
    If that didn't help, troubleshoot Safari extensions.
    From the Safari menu bar click Safari > Preferences then select the Extensions tab. Turn that OFF, quit and relaunch Safari to test.
    If that helped, turn one extension on then quit and relaunch Safari to test until you find the incompatible extension then click uninstall.

  • I am unable to print PDF's using either Adobe Reader or Safari. In Adobe Reader, I get an error message from my Cannon printer that says, "/usr.libexec/cups/filter/pstocupsraster failed". In Safari, I can only print the first page of a PDF.

    To try to resolve this problem, I have done the following actions.
    1 - I have run Disk Warrior.
    2 - I have repaired permissions.
    3 - I have deleted all plist that are either Cannon or Adobe.
    4 - I have downloaded and installed the lastest versions of Adobe Reader and the Cannon printer drivers.
    I am still unable to print PDF's.
    In Safari, I can print only the first page. In a multipage PDF, Safari only seems to recognize the first page.
    In Adobe Reader, I get an error message from my printer: "/usr/libexec/cups/filter/pstocupsraster failed".
    Any help would be greatly appreicated!

    Quit Safari.
    Open the Library folder in your home folder as follows:
    ☞ If running OS X 10.7 or later, hold down the option key and select Go ▹ Library from the Finder menu bar.
    ☞ If running an older version of OS X, select Go ▹ Go to Folder… from the Finder menu bar and copy the line below into the text box that opens:
    ~/Library
    Delete the following items from the Library folder:
    Caches/com.apple.Safari/Cache.db
    Preferences/com.apple.quicktime.plugin.preferences.plist
    Preferences/QuickTime Preferences
    Relaunch Safari and test.
    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ If you’re running OS X 10.7 or later, open LaunchPad. Click Utilities, then Console in the page that opens.
    Select "/var/log/cups/error_log" from the file list. Post the messages from the time of the last printing attempt.
    Post the log text, please, not a screenshot. If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message.

  • Error message from the source system, Caller 09 contains an error message.

    Hi,
        Guru's, i got an error massage when my process chain is running(Daily) in BIW 7.0, the error got in Data Loading from source to PSA or data targets. The errors having the below details
    Error message from the source system
    Diagnosis
    An error occurred in the source system.
    System Response
    Caller 09 contains an error message.
    Further analysis:
    The error occurred in Extractor .
    Refer to the error message.
    Procedure
    How you remove the error depends on the error message.
    Note
    If the source system is a Client Workstation, then it is possible that the file that you wanted to load was being edited at the time of the data request. Make sure that the file is in the specified directory, that it is not being processed at the moment, and restart the request.   "
    Can any body help me out of this situation what to do and how to resolv ethe problem.
    Thanks and Regards,.
    Taps....

    Caller 09 is a very common issue - please search the forums before posting....
    Arun

  • Error message from source system

    Hi All,
    We have an infocube and ods which is being loaded from another ods. This is included in a process chain.
    In the process chain the Infopackage execution step has failed. When I right click and go for display messages, I found the following message in Messages tab:
    Error message from the source system
    Diagnosis
    An error occurred in the source system.
    System response
    Caller 09 contains an error message.
    Further analysis:
    The error occurred in Extractor .
    Refer to the error message.
    Procedure
    How you remove the error depends on the error message.
    Note
    If the source system is a Client Workstation, then it is possible that the file that you wanted to load was being edited at the time of the data request. Make sure that the file is in the specified directory, that it is not being processed at the
    And in Indiv Messages tab,
    Delta upload is only possible after successful initialization.
    Errors in source system.
    I tried to update the data targets from the initial ODS manualy but in vain.
    Any Help is awarded with points.
    Thanks
    AP

    Hi,
      Goto Info pack -> on menu bar select scheduler -> select init options for source system -> one request with green status -> select it and  click on delete symbol , it will delete the init. you can cross verify this in the base ODS where you dint find data mart status(after refresh). now  select init delta process under that select init without data transfer and schedule the load it will update one record and init flag to your source ODS.
    Note: if the last request is not updated from soruce ods to targets for that also you will find data mart status for this select the particular data mart -> click on delete symbol it will delete for the particular request (if it is updated to target it will not allow you to delete) then do delta load it will update the request which is not loaded from source ods to next targets.
    Regards
    Sankar

  • Error Message from  SAP GUI

    Hi,
    I have designed a Custom screen for one of my requirements. However when the screen is displayed, I am facing an error message from SAP Front End Server that  says " Erroneous data received from server. Application may not work correctly".
    What could be the reason ?
    Thanks & Regards,
    Venkatesh.

    Hi,
    Please check the belos SAP notes
    1453114    Maximum string length
    1161022    Dialog box "Erroneous data received from server"
    1524462 - Erroneous Data received from server. Application may not work correctly.
    Regards,
    Naveen.

  • Error message from Adobe Reader. cannot extract the embedded font 'LICCMC+MyriadPro-Light'. some characters may not display or print correctly. Print looks like gibberish

    Trying to view/print PDF documents from website. Print looks like gibberish and is unreadable. Problem is with the embedded fonts. Error message from Adobe says cannot extract the embedded font 'LICCMC+MyriadPro-Light'. some characters may not display or print correctly.

    Try Adobe support, that's not a Firefox support issue. <br />
    http://forums.adobe.com/index.jspa

Maybe you are looking for