Error Message from Tech Tool Pro

I've run Tech Tool Pro and got the following message:
File is corrupt or is an unsupported file format: /Library/Frameworks/TSLicense.framework/Versions/A/Resources/EWSMac-GC.framewor k/Versions/A/Resources/lock_black.png
I've opened the hidden Library folder and can't find a folder "Frameworks" in it so I'm at a dead end. I'm not sure what that lock_black.png file does but I don't seem to have any problems.
I was going to go in and delete it and see if a shut down/restrart would replace it with a good file.
Can anyone help with this? Thanks

Ignore it; that appears to be normal. In any case, the item in question is just a picture.
(79117)

Similar Messages

G5 will not boot from system disk or from Tech Tool Pro 5

Hi everyone - Having a bit of trouble and hoped I might find some answers here.
I suspect my system drive was having some issues as it sounded like it was being taxed and strained as I would open up applications from it. Upon verifying the disk using Disk Utilities, the test would stop short with the following message:
First Aid Failed
Disk Utility stopped verifying "Macintosh HD" because the following error was encountered
Filesystem verify or repair failed
In addition, an error message came up (in red) on the disk utility screen as well saying:
Volume header needs minor repair
The volume Macintosh HD needs to be repaired
Error: Filesystem verify or repair failed
Normally from here, I'd start up the computer from the Tech Tool Pro 5 disk (holding down C key upon restart). But when I did this, the computer never responded. Instead, the power was on but the screens went black and the computer went into a very quiet "idle" mode.
After about a minute, the fans began ramping up pretty high (and loud). This went on until I finally had to manually shut down the computer by holding the power switch down for a few seconds. I didn't know what else to do. Those fans were not coming down (not even after 10 minutes).
Anyway, I pushed the power button again and held the C key down. Still, nothing.... The fans stayed idle, for a little while and then ramped up again just like last time. I hit that same dead end and powered down the computer via the power button.
Is there an alternate way to boot the computer from Tech Tool Pro or the original start up disks? I'm having no luck, here.
I'm on my way into town to purchase a new internal drive (something with about 1TB of space) so that my pro apps can swim a little instead of being being bogged down on a 250G drive.
Thanks for any assistance, folks!
Oh yeah.... Happy New Year to everyone!!
Steve

The Install disk has version 10.4 on it. I have also tried booting from my OS 10.5 disk but with no avail.
However, here is an update on my plight.
Apple tech says that after hearing the symptoms, he thinks that one of the processors is shot. Being that my particular model of G5 (dual 2.7 processors) is a liquid cooled machine, it's possible that some sort of leak has formed and has either taken out a processor or has caused a processor to overheat. He says that this model of G5 has been known to do that. In this case, nothing will boot which makes me think that my original system drive may actually be okay. I'm taking it in for the tech to look at it and just be sure that's the problem. However, if it is a dead processor, the part alone would run $799 plus labor to install it. Frankly, that's just too much for me to pay to keep this old G5. I'd rather put that money towards a new or reconditioned Mac Pro 8 core or quad core machine.
I've owned several Mac computers in the past and perhaps this is the frustration talking but it seems that no matter how diligent you are in maintaining your Macintosh, these machines only seem to last about 5 years before something majorly wrong happens (mother board, processor, etc). Can I expect this same, limited time frame from a new Mac Pro? I mean, am I just being paranoid?

Tech Tool Pro and iMac 2009

There is a disturbing message re: Tech Tool Pro 5 at its place in the Apple Store website
(http://store.apple.com/us/product/TT757LL/A?fnode=MTY1NDA1Mw&mco=MTA4NTE4NzE).
Basically he says it corrupted his hard drive totally.
I used to rely on an earlier version this software for my old G4 desktop and would like to know if the current version is safe to use on the iMac. Anybody using it regularly?

I am a little touchy since one of my older Macs was ruined recently by a well-known anti-virus utility. The hard disk was rendered irreparable.
Software cannot generally ruin drive hardware; it can cause data corruption, but a reformat should resolve that type of problem. In the case you mentioned, I would suspect that the hard drive was already becoming somewhat unreliable. The extra stress from doing frequent malware scans (which basically makes the drive accesses every used sector on the drive repeatedly) caused it to fail completely.
Now that my data is backed up to within one hour using Time Machine, I am less likely to need a tool like TechTool Pro. If I had data corruption, I am more likely to use the +erase the drive and restore from backup+ approach, not the +repair the errors with TechTool Pro+ approach. The maintenance checks are useful, but the important checks can be done with Disk Utility. The optimization features are useful too, but not something that has to be done.

Tech Tool Pro and/or Drive Genius (Background monitor)

I have both Tech Tool Pro 6 and Drive Genius 3, acquired independently through software bundles. I installed both to test them out and now I have both background services running as well: DrivePulse (from Drive Genius 3) and Tech Tool Protection (from Tech Tool Pro 6).
Both background processes monitor my system but I am pretty sure running both is overkill. Hence my questions:
Would running both all the time cause problems? (so far so good for me...)
If it is overkill, which one should I run and why? What are you preferences?
Or should I not run any at all and just test my system once in a while with either app?
Thanks so much for your input!

In fact you don't need either. If you don't have a problem I would not use either one.

I've recently received an error message from Time Machine that my Macbook Pro's sparsebundle is in use. What is this and what can I do about it?

I've recently received an error message from Time Machine that my Macbook Pro's sparsebundle is in use. What is this and what can I do about it?

This is asked at least 5-6 times a day here.
Look at the right hand column.. more like this.
It is a bug in Mountain Lion.
Read C12 http://pondini.org/TM/Troubleshooting.html
But the fast solution.. unplug the TC.. count to 10.. plug it back in.

Disk utility says SMART error but Tech Tools Pro says SMART passed

Disk Utility on my Mac Pro (6GB ram, dual dual, 10.5.5) is saying my primary HD (a Seagate 1TB, one of three) has failed SMART. Tech Tools pro says it's fine and passes SMART (and all the other tests). I've got backups (Time Machine and tar files) and a new disk on the way. However I'd like to be able to know what exactly Disk Utility thinks the SAMRT error is - is there any way of finding our or is it opaque to the user?

If the drive is possible defective, then you may be able to have it replaced at no cost because it's in warranty. Most drives carry at least a 3 year manufacturer's warranty. You would contact the manufacturer about a warranty replacement if your Apple warranty has expired. If you still have Apple's warranty in effect then contact AppleCare about the replacement.

Hung during Tech Tool Pro volume rebuild- what to do?

Working on my ex's messed up 2007 MacBook 2.2ghz OS 10.5.8.
Extreme heat problems, was hanging a lot, and Disk First Aid failed immediately with volume errors. With some diffculty, i got his critical files backed up to an external drive (he had no backup... i have no comment) and booted it with Tech Tool Pro 5 -retail DVD, not the applecare version- with OS 10.5.7 and it also immediately found trouble with the disk directory, tho the SMART parameters were all PASS except for internal temperature (which has been high enuf to warp the bottom of the case).
But when i clicked Run Volume Rebuild, it hung in Acquiring Directory Structures. TTP's Elapsed Time clock stopped at 07:18... an hour ago. Fan is running like crazy.
does this indicate what i think it might... a non-repairable hard drive?
meanwhile, how do i get out of the TTP volume repair hang, pref without further damage? (HD was at least mounting and files accessible)
clicking the "X" to stop it just makes it "tink" with no change.
Trying to quit TTP causes an endless "canceling running jobs" loop.
Should i just force shutdown and call it a day?
He will probably buy a new Macbook rather than replace the drive in this one, and it'd be nice if the apple store could migrate directly from this drive ... unless it's really easy to migrate across two generations, leopard to lion, from the Time Machine backup i got on an external drive after the internal drive was already having trouble...? (i've never restored or migrated from Time Machine).

The Protection module of the Safety suite saves directory structure information from each of my four drives to each of the four drives. The Diagnostics module checks the volume structures of each of the drives, and the Smart module runs the SMART routines to check each of the two compatible drives for any impending troubles.
When I asked whether I could be assured the new version wouldn't behave the same way, the reply I received was:
"There are very few reports of problems with the features configured in the TechTool Protection system preferences pane as of version 5.0.7. The previously-reported problems were difficult to reproduce, and solving them required a substantial rewrite of the code in earlier versions in the TechTool Pro 5.0.x series."
I'm not convinced that was a 'yes.'
Your iCal idea sounds interesting, but keep in mind that the Safety suite of modules are within the Tech Tool Pro application itself and, when automatically launched, run in the background without the main application itself launching. Meaning, that iCal might launch Tech Tool Pro at the correct time, but will it launch the modules within?

When I use the shortcut to open a new window in safari (command N), I get a 404 error message from Google. How do I change where 'Command N' routes to?

When I use the shortcut to open a new window in safari (command N) on my Macbook Pro, I get a 404 error message from Google. How do I change where 'Command N' routes to?

It's not necessary to change the Command N keystroke..
From your Safari menu bar click Safari > Preferences then select the Privacy tab.
Click: Remove All Website Data
Then delete the cache.
Open a Finder window. From the Finder menu bar click Go > Go to Folder
Type or copy paste the following
~/Library/Caches/com.apple.Safari/Cache.db
Click Go then move the Cache.db file to the Trash.
Quit and relaunch Safari to test.
If that didn't help, troubleshoot Safari extensions.
From the Safari menu bar click Safari > Preferences then select the Extensions tab. Turn that OFF, quit and relaunch Safari to test.
If that helped, turn one extension on then quit and relaunch Safari to test until you find the incompatible extension then click uninstall.

Error Message from VM TMS 13.0

Dear all,
We have receive some error message from the VM TMS 13.0, that is installed a month ago.
<ErrorCode 1000>
Message="Faulting application name: TMSSNMPService.exe, version: 1.0.4008.29206, time stamp: 0x4d12159c Faulting module name: mscorlib.ni.dll, version: 4.0.30319.18444, time stamp: 0x52717d7e Exception code: 0xc0000005 Fault offset: 0x0000000000cd5bf7 Faulting process id: 0x116c Faulting application start time: 0x01cf68076319516f Faulting application path: C:\\Program Files (x86)\\TANDBERG\\TMS\\Services\\TMSSNMPService.exeFaulting module path: C:\\Windows\\assembly\\NativeImages_v4.0.30319_64\\mscorlib\\abf62e6545d2802fc60286678a67e6bf\\mscorlib.ni.dll Report Id: 371654ff-d3fb-11e3-98ea-005056b1027a"
<ErrorCode 1026>
Message="Application: TMSSNMPService.exe Framework Version: v4.0.30319 Description: The process was terminated due to an unhandled exception. Exception Info: System.AccessViolationException Stack: at System.Runtime.InteropServices.Marshal.ReadInt64(IntPtr, Int32) at Tandberg.CommLib.SnmpLib.TrapHandling.SnmpTrapHandler.VbToObject(Tandberg.CommLib.SnmpLib.WinSnmp.SMIVALUE ByRef) at Tandberg.CommLib.SnmpLib.TrapHandling.SnmpTrapHandler.VblToHashtable(IntPtr) at Tandberg.CommLib.SnmpLib.TrapHandling.SnmpTrapHandler.OnSnmpMessage(IntPtr, IntPtr, Int32, UInt32, UInt32, IntPtr)"
<ErrorCode 7031>
Message="The TMSSnmpService service terminated unexpectedly. It has done this 1 time(s). The following corrective action will be taken in 60000 milliseconds:
Any comments on the above error?
Best Regards,
Ben Lai

This seems to be happening on 14.2.2 as well.
Component: Application Error
Severity: Warning
Event class: /App/Failed
Device class: /Server/Windows/WMI/TMS
Systems: None
Summary: Faulting application name: wmiprvse.exe, version: 6.1.7600.16385, time stamp: 0x4a5bc794
Faulting module name: ole32.dll, version: 6.1.7600.16624, time stamp: 0x4c2984e3
Exception code: 0xc0000005
Fault offset: 0x00000000000393a9
Faulting process id:
Message:
Faulting application name: wmiprvse.exe, version: 6.1.7600.16385, time stamp: 0x4a5bc794
Faulting module name: ole32.dll, version: 6.1.7600.16624, time stamp: 0x4c2984e3
Exception code: 0xc0000005
Fault offset: 0x00000000000393a9
Faulting process id: 0x39c4
Faulting application start time: 0x01d04d36eb9b6c36
Faulting application path: C:\Windows\system32\wbem\wmiprvse.exe
Faulting module path: C:\Windows\system32\ole32.dll
Report Id: e334bd6f-b990-11e4-aa1d-842b2b6be310
http://tools.cisco.com/security/center/viewAlert.x?alertId=29142

Internal hard drive won't mount after running Tech Tools Pro 5

HELP.
We have an imac 2ghz Intel Core 2 running OS 10.6.8.
I ran Tech Tools Pro 5 to rebuild directory, optimize files, optimize volume. It ran over nightbut seemed to hang up optimizing the volume.
Now the HD doesn't mount.
I've tried a few fixes. Including running disk utility from a CD. The disk utility says the directory is okay but doesn't see the HD to verify or repair permissions.
I've tried zapping the pram and safe boot, neither of which worked.
I've been able to use the computer by booting from an external start up hd.
Oddly, I ran a Time Machine back up prior to running TTP, but for some reason the only back up I see is from 3 months ago.
Not sure why the recent back up didn't happen, but were missing some very important recent docs.
I downloaded a trial version of Stellar Pheonix Mac Data Recovery and it seems to be able to see all of the data on the main HD.
I'm wondering whether or not to spend $100 for full version to attempt to restore content of HD to an external.
If I do this, I assume I'll have to erase the HD and reinstall data from the Stellar Pheonix collection, hoping that it's all intact.
Does anyone have any other suggestions to get the HD mounted????

Hi, never "Optimize" a drive before Repairing it AND having a backup clone to boot from.
I assume I'll have to erase the HD and reinstall data from the Stellar Pheonix collection, hoping that it's all intact.
No, I don't think you want an erase at all, you want a freah external drive to recover to first off.

On starting up firefox i am getting an error message from javascript application telling me that my username is an invalid username/password combination.If i continue to get this error message,try entering my email address as my username.

Hi,on starting firefox which i have used solely as my browser for years i am now getting an error message from java script application that shows my username followed by a message saying; 'username'-Invalid username/password combination.If you keep getting this error,try entering your email address as your username'. I then press the OK button within that error message box and it dissapears and everything seems ok although hover my cursor over the mail(envelope) icon and it says not connected.
I only started having this problem since downloading firefox 4.It also does not tell me where this problem is occuring so i do not know where to log on with this information.I would be most grateful for any help with this matter.Many thanks.

Take a look in the Error Console for details about that.
Tools > Error Console <br />
Right-click the message and use '''Copy''' to get that complete message.

Getting more detailed error messages from Adobe Acrobat

Hi
Is there a way to get more detailed error messages from Adobe Acrobat reader when he detecs an error in a PDF file?
My program generates PDF files. There is one that throws an error in Acrobat while GhostScript and Google Chromes PDF Reader display it correctly.
I wonder where the error is, but the error message is just "expected dictionary", when I hold CTRL and press "OK".
GhostScript usually gives useful error messages, but it has no error this time.

More specifically, Acrobat Pro!
- Dov

I am unable to print PDF's using either Adobe Reader or Safari. In Adobe Reader, I get an error message from my Cannon printer that says, "/usr.libexec/cups/filter/pstocupsraster failed". In Safari, I can only print the first page of a PDF.

To try to resolve this problem, I have done the following actions.
1 - I have run Disk Warrior.
2 - I have repaired permissions.
3 - I have deleted all plist that are either Cannon or Adobe.
4 - I have downloaded and installed the lastest versions of Adobe Reader and the Cannon printer drivers.
I am still unable to print PDF's.
In Safari, I can print only the first page. In a multipage PDF, Safari only seems to recognize the first page.
In Adobe Reader, I get an error message from my printer: "/usr/libexec/cups/filter/pstocupsraster failed".
Any help would be greatly appreicated!

Quit Safari.
Open the Library folder in your home folder as follows:
☞ If running OS X 10.7 or later, hold down the option key and select Go ▹ Library from the Finder menu bar.
☞ If running an older version of OS X, select Go ▹ Go to Folder… from the Finder menu bar and copy the line below into the text box that opens:
~/Library
Delete the following items from the Library folder:
Caches/com.apple.Safari/Cache.db
Preferences/com.apple.quicktime.plugin.preferences.plist
Preferences/QuickTime Preferences
Relaunch Safari and test.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running OS X 10.7 or later, open LaunchPad. Click Utilities, then Console in the page that opens.
Select "/var/log/cups/error_log" from the file list. Post the messages from the time of the last printing attempt.
Post the log text, please, not a screenshot. If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message.

Error message from the source system, Caller 09 contains an error message.

Hi,
Guru's, i got an error massage when my process chain is running(Daily) in BIW 7.0, the error got in Data Loading from source to PSA or data targets. The errors having the below details
Error message from the source system
Diagnosis
An error occurred in the source system.
System Response
Caller 09 contains an error message.
Further analysis:
The error occurred in Extractor .
Refer to the error message.
Procedure
How you remove the error depends on the error message.
Note
If the source system is a Client Workstation, then it is possible that the file that you wanted to load was being edited at the time of the data request. Make sure that the file is in the specified directory, that it is not being processed at the moment, and restart the request. "
Can any body help me out of this situation what to do and how to resolv ethe problem.
Thanks and Regards,.
Taps....

Caller 09 is a very common issue - please search the forums before posting....
Arun

Error message from source system

Hi All,
We have an infocube and ods which is being loaded from another ods. This is included in a process chain.
In the process chain the Infopackage execution step has failed. When I right click and go for display messages, I found the following message in Messages tab:
Error message from the source system
Diagnosis
An error occurred in the source system.
System response
Caller 09 contains an error message.
Further analysis:
The error occurred in Extractor .
Refer to the error message.
Procedure
How you remove the error depends on the error message.
Note
If the source system is a Client Workstation, then it is possible that the file that you wanted to load was being edited at the time of the data request. Make sure that the file is in the specified directory, that it is not being processed at the
And in Indiv Messages tab,
Delta upload is only possible after successful initialization.
Errors in source system.
I tried to update the data targets from the initial ODS manualy but in vain.
Any Help is awarded with points.
Thanks
AP

Hi,
Goto Info pack -> on menu bar select scheduler -> select init options for source system -> one request with green status -> select it and click on delete symbol , it will delete the init. you can cross verify this in the base ODS where you dint find data mart status(after refresh). now select init delta process under that select init without data transfer and schedule the load it will update one record and init flag to your source ODS.
Note: if the last request is not updated from soruce ods to targets for that also you will find data mart status for this select the particular data mart -> click on delete symbol it will delete for the particular request (if it is updated to target it will not allow you to delete) then do delta load it will update the request which is not loaded from source ods to next targets.
Regards
Sankar

Error Message from Tech Tool Pro

Similar Messages

Maybe you are looking for