Error while applying the Service Policy
Hi,
I am getting the below error while applying the service policy to the Interface.
I have set the mpls exp 4 as well as want to limit the bandwidth to 1Mbps
PE#sh policy-map setexp-GBoIP
Policy Map setexp-GBoIP
Class GBoIP-traffic
set mpls experimental imposition 4
police cir 1024000 bc 32000
conform-action transmit
exceed-action drop
PE(config-if)#int vlan 2007
PE(config-if)#service-policy input setexp-GBoIP
QoS-ERROR: Addition/Modification made to policymap setexp-GBoIP and class GBoIP-traffic is not valid, command is rejected
As well as I have created new clas--map with priority and Bandwidth and applied in output direction, I got the belwo error while applying the Service policy in
PE(config-if)#service-policy out TEST
bandwidth command is not supported in output direction for this interface
PE(config-if)#service-policy output TEST
priority command is not supported in output direction for this interface
Any idea why so ?
Thanks in Advance.
Regards,
Nilesh
Check the current value of IGW_AWARDS_S sequence and make sure the MINVALUE in the patch (i.e. 10000) is not greater than the current one.
OERR: ORA 4007 MINVALUE cannot be made to exceed the current value (Doc ID 19824.1)
You may also log a SR.
Thanks,
Hussein
Similar Messages
-
Error : While applying the Patch 4440000
Error : While applying the Patch 4440000
FAILED: file igwprop.odf on worker 1 for product igw username IGW.
When i check the worker log file i got this error
The sequence IGW_AWARDS_S in the database is defined as:
MINVALUE = 1 MAXVALUE = 2147483647 INCREMENT BY = 1
CYCLE = NO ORDER = NO CACHE = 1000
which should be defined as:
MINVALUE = 10000 MAXVALUE = 2147483647 INCREMENT BY = 1
CYCLE = NO ORDER = NO CACHE = 1000
(Note: The cache value for sequence IGW_AWARDS_S is 20 in the ODF file. The value 1000 is being used instead because this provides better performance when selecting from the sequence.)
Alter the sequence with :
Start time for statement below is: Sun Oct 06 2013 22:16:28
ALTER SEQUENCE IGW.IGW_AWARDS_S MINVALUE 10000
AD Worker error:
The following ORACLE error:
ORA-04007: MINVALUE cannot be made to exceed the current value
occurred while executing the SQL statement:
ALTER SEQUENCE IGW.IGW_AWARDS_S MINVALUE 10000
AD Worker error:
Unable to compare or correct sequences
because of the error above
Time when worker failed: Sun Oct 06 2013 22:16:28
plz help me in solving this.Check the current value of IGW_AWARDS_S sequence and make sure the MINVALUE in the patch (i.e. 10000) is not greater than the current one.
OERR: ORA 4007 MINVALUE cannot be made to exceed the current value (Doc ID 19824.1)
You may also log a SR.
Thanks,
Hussein -
Error while executing the service - The service method not defined error
Hi,
I am using Oracle UCM Content server 11g. I have created a custom service using component wizard. I have provided class name and method correct in the service declarations. The method should return manipulated Revision Label value. I am executing the service as a direct service and not subservice from a resource file using the following command.
<$executeService("servicename")$>
The serice is getting called but I am getting the following error log
Event generated by user 'weblogic' at host 'localhost:16200'. Unable to execute service Edit_Revision_Label and function generateRevLabelInfo.
The service method 'generateRevLabelInfo' is not defined. [ Details ]
An error has occurred. The stack trace below shows more information.
!csUserEventMessage,weblogic,localhost:16200!$!csServiceDataException,Edit_Revision_Label,generateRevLabelInfo!$!csMethodNotDefined,generateRevLabelInfo
intradoc.common.ServiceException: !csServiceDataException,Edit_Revision_Label,generateRevLabelInfo!$
*ScriptStack Edit_Revision_Label
Edit_Revision_Label,dDocName=3:generateRevLabelInfo,dDocName=
at intradoc.server.ServiceRequestImplementor.buildServiceException(ServiceRequestImplementor.java:2115)
at intradoc.server.Service.buildServiceException(Service.java:2260)
at intradoc.server.Service.createServiceExceptionEx(Service.java:2254)
at intradoc.server.Service.createServiceException(Service.java:2249)
at intradoc.server.ServiceRequestImplementor.handleActionException(ServiceRequestImplementor.java:1766)
at intradoc.server.ServiceRequestImplementor.doAction(ServiceRequestImplementor.java:1716)
at intradoc.server.Service.doAction(Service.java:477)
at intradoc.server.ServiceRequestImplementor.doActions(ServiceRequestImplementor.java:1458)
at intradoc.server.Service.doActions(Service.java:472)
at intradoc.server.ServiceRequestImplementor.executeSubServiceCode(ServiceRequestImplementor.java:1322)
at intradoc.server.Service.executeSubServiceCode(Service.java:3866)
at intradoc.server.ServiceRequestImplementor.executeServiceEx(ServiceRequestImplementor.java:1200)
at intradoc.server.Service.executeServiceEx(Service.java:3861)
at intradoc.server.ServiceRequestImplementor.executeSafeServiceInNewContext(ServiceRequestImplementor.java:1231)
at intradoc.server.Service.executeSafeServiceInNewContext(Service.java:3856)
at intradoc.server.script.ServiceScriptExtensions.evaluateFunction(ServiceScriptExtensions.java:269)
at intradoc.common.DynamicHtmlMerger.computeFunction(DynamicHtmlMerger.java:1430)
at intradoc.common.DynamicHtmlMerger.evaluateGrammarElement(DynamicHtmlMerger.java:908)
at intradoc.common.DynamicHtmlMerger.substituteVariable(DynamicHtmlMerger.java:623)
at intradoc.common.DynamicHtml.substituteVariable(DynamicHtml.java:1394)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1110)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtml(DynamicHtml.java:991)
at intradoc.common.DynamicHtmlMerger.outputDynamicHtmlPage(DynamicHtmlMerger.java:2007)
at intradoc.server.Service.buildResponsePage(Service.java:1267)
at intradoc.server.Service.doResponse(Service.java:2076)
at intradoc.server.ServiceRequestImplementor.doRequest(ServiceRequestImplementor.java:802)
at intradoc.server.Service.doRequest(Service.java:1890)
at intradoc.server.ServiceManager.processCommand(ServiceManager.java:435)
at intradoc.server.IdcServerThread.processRequest(IdcServerThread.java:265)
at intradoc.idcwls.IdcServletRequestUtils.doRequest(IdcServletRequestUtils.java:1343)
at intradoc.idcwls.IdcServletRequestUtils.processFilterEvent(IdcServletRequestUtils.java:1715)
at intradoc.idcwls.IdcIntegrateWrapper.processFilterEvent(IdcIntegrateWrapper.java:222)
at sun.reflect.GeneratedMethodAccessor1173.invoke(Unknown Source)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at idcservlet.common.IdcMethodHolder.invokeMethod(IdcMethodHolder.java:87)
at idcservlet.common.ClassHelperUtils.executeMethodEx(ClassHelperUtils.java:305)
at idcservlet.common.ClassHelperUtils.executeMethodWithArgs(ClassHelperUtils.java:278)
at idcservlet.ServletUtils.executeContentServerIntegrateMethodOnConfig(ServletUtils.java:1600)
at idcservlet.IdcFilter.doFilter(IdcFilter.java:352)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
at oracle.security.jps.ee.http.JpsAbsFilter$1.run(JpsAbsFilter.java:111)
at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:313)
at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:413)
at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:94)
at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:161)
at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
at oracle.dms.servlet.DMSServletFilter.doFilter(DMSServletFilter.java:136)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
at oracle.security.jps.ee.http.JpsAbsFilter$1.run(JpsAbsFilter.java:111)
at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:313)
at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:413)
at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:94)
at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:161)
at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.wrapRun(WebAppServletContext.java:3715)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3681)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:120)
at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2277)
at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2183)
at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1454)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:209)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:178)
Caused by: intradoc.data.DataException: !csMethodNotDefined,generateRevLabelInfo
at intradoc.server.Service.doCodeEx(Service.java:561)
at intradoc.server.Service.doCode(Service.java:505)
at intradoc.server.ServiceRequestImplementor.doAction(ServiceRequestImplementor.java:1643)
at intradoc.server.Service.doAction(Service.java:477)
at intradoc.server.ServiceRequestImplementor.doActions(ServiceRequestImplementor.java:1458)
at intradoc.server.Service.doActions(Service.java:473)
at intradoc.server.ServiceRequestImplementor.executeSubServiceCode(ServiceRequestImplementor.java:1323)
at intradoc.server.Service.executeSubServiceCode(Service.java:3867)
at intradoc.server.ServiceRequestImplementor.executeServiceEx(ServiceRequestImplementor.java:1200)
at intradoc.server.Service.executeServiceEx(Service.java:3862)
at intradoc.server.ServiceRequestImplementor.executeSafeServiceInNewContext(ServiceRequestImplementor.java:1231)
at intradoc.server.Service.executeSafeServiceInNewContext(Service.java:3857)
at intradoc.server.script.ServiceScriptExtensions.evaluateFunction(ServiceScriptExtensions.java:269)
at intradoc.common.DynamicHtmlMerger.computeFunction(DynamicHtmlMerger.java:1430)
at intradoc.common.DynamicHtmlMerger.evaluateGrammarElement(DynamicHtmlMerger.java:908)
at intradoc.common.DynamicHtmlMerger.substituteVariable(DynamicHtmlMerger.java:623)
at intradoc.common.DynamicHtml.substituteVariable(DynamicHtml.java:1394)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1110)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtmlEx(DynamicHtml.java:1227)
at intradoc.common.DynamicHtml.outputHtmlFromStart(DynamicHtml.java:1020)
at intradoc.common.DynamicHtml.outputHtml(DynamicHtml.java:991)
at intradoc.common.DynamicHtmlMerger.outputDynamicHtmlPage(DynamicHtmlMerger.java:2007)
at intradoc.server.Service.buildResponsePage(Service.java:1267)
at intradoc.server.Service.doResponse(Service.java:2076)
at intradoc.server.ServiceRequestImplementor.doRequest(ServiceRequestImplementor.java:802)
at intradoc.server.Service.doRequest(Service.java:1890)
at intradoc.server.ServiceManager.processCommand(ServiceManager.java:435)
at intradoc.server.IdcServerThread.processRequest(IdcServerThread.java:265)
at intradoc.idcwls.IdcServletRequestUtils.doRequest(IdcServletRequestUtils.java:1346)
at intradoc.idcwls.IdcServletRequestUtils.processFilterEvent(IdcServletRequestUtils.java:1715)
at intradoc.idcwls.IdcIntegrateWrapper.processFilterEvent(IdcIntegrateWrapper.java:222)
at sun.reflect.GeneratedMethodAccessor1173.invoke(Unknown Source)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at idcservlet.common.IdcMethodHolder.invokeMethod(IdcMethodHolder.java:88)
at idcservlet.common.ClassHelperUtils.executeMethodEx(ClassHelperUtils.java:305)
at idcservlet.common.ClassHelperUtils.executeMethodWithArgs(ClassHelperUtils.java:278)
at idcservlet.ServletUtils.executeContentServerIntegrateMethodOnConfig(ServletUtils.java:1600)
at idcservlet.IdcFilter.doFilter(IdcFilter.java:352)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:57)
at oracle.security.jps.ee.http.JpsAbsFilter$1.run(JpsAbsFilter.java:111)
at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:313)
at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:413)
at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:94)
at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:161)
at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:57)
at oracle.dms.servlet.DMSServletFilter.doFilter(DMSServletFilter.java:136)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:57)
at oracle.security.jps.ee.http.JpsAbsFilter$1.run(JpsAbsFilter.java:111)
at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:313)
at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:413)
at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:94)
at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:161)
at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:57)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.wrapRun(WebAppServletContext.java:3715)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3681)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:120)
at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2277)
at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2183)
at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1454)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:209)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:178)
Please let me know the suggestions and the resolution on the above issue
Thanks in advance,
SarangHirva wrote:
Trying to get access to the sun convergence we get this error
"Error while executing the service request : : Login to Mail Service failed " after a look around we found out that the problem was that some one had deleted the msg-admin-server user from the ldap.What else was "accidentally" deleted? Do you have audit logging enabled for Directory Server?
but still doesnt work? where else should we look?Messaging Server also creates a msg-admin group ("cn=Messaging End User Administrators Group") which is used for Directory Server ACI purposes. You can see the entries that Messaging Server added during initial configuration by reviewing the *.ldif files under the following directory (MS7.0 32bit):
/var/opt/sun/comms/messaging/install/Regards,
Shane. -
Error while creating the service entry sheet in PRD
Hi All,
We are in SAP R/3 4.7 Version. OF39 settings are 58 & 61 Statistical update only ! Now my case is i assigned Rs.100 Budget agaisnt one FC & Comitmetn item & created one service Purchase order Rs.80 & Make down payment against same PO Rs.80.
Now as per above mentioned scenario ,system should allow new Purchase order creation for Rs. 20. But my system is allowing to create up to Rs.100. I am very much sure system not allowed the same and also allow for service entry creation for first PO. But system given error message while doing the Service sheet.
Kindly advice. OF39 settings are OK .Both are statistical only
Rgds
ManiSumaHi Manisuma, statistical update is recommended to be used only at the begining of a document chain (i.e.purchase requisition or funds reservation) cause if you set it in intermediate documents as you did the budget is set as available, in your example the downpayment reduces the purchase order commitment, and as the downpayment is statistical it does not affect the Availability Control, so the amount (80 in your example) becomes available again so new commitments/actual can be created.
Regards
Cesar -
Error While applying the maintenance pack12.1.1
Hi All,
While upgradeing the applications from12.0.4 to 12.1.1 ,While applying the maintenance pack patch(7303030) iahave encountered the below error
worker failed with the below Error
sqlplus -s APPS/***** @/oracle/AMALCRP/apps/apps_st/appl/zx/12.0.0/patch/115/sql/zxmigratefc.sql
DECLARE
ERROR at line 1:
ORA-01422: exact fetch returns more than requested number of rows
ORA-06512: at "APPS.ZX_FC_MIGRATE_PKG", line 386
ORA-06512: at "APPS.ZX_FC_MIGRATE_PKG", line 978
ORA-06512: at "APPS.ZX_FC_MIGRATE_PKG", line 5017
ORA-06512: at line 6
Please let me know if ther is any possible solution for this
Thanks iN Advance
SagiFor the first Error
Sol:1. Download patch 8593634:R12.ZX.B and unzip the patch to a temoprary folder.
2. Backup the file $ZX_TOP/patch/115/sql/zxfcmigrateb.pls
cp $ZX_TOP/patch/115/sql/zxfcmigrateb.pls $ZX_TOP/patch/115/sql/zxfcmigrateb.pls-BKP
3. Copy the file zxfcmigrateb.pls from the patch location (/<PatchUnzipLocation>/zx/patch/115/sql/zxfcmigrateb.pls) to $ZX_TOP/patch/115/sql/zxfcmigrateb.pls
4. Execute the newly copied file using SQLPLUS:
sqlplus apps/<apps password>
SQL> @ $ZX_TOP/patch/115/sql/zxfcmigrateb.pls
5. Now re-start the failed worker for patch
Next i got the Error which is mentionedin the note 1299350.1
Sol:
1. Download patch 10250232:R12.ZX.A and unzip the patch to a temoprary folder.
2. Backup the file $ZX_TOP/patch/115/sql/zxfcmigrateb.pls
cp $ZX_TOP/patch/115/sql/zxfcmigrateb.pls $ZX_TOP/patch/115/sql/zxfcmigrateb.pls-BKP
3.
Copy the file zxfcmigrateb.pls from the patch location
(/<PatchUnzipLocation>/zx/patch/115/sql/zxfcmigrateb.pls) to
$ZX_TOP/patch/115/sql/zxfcmigrateb.pls
4. Execute the newly copied file using SQLPLUS:
sqlplus apps/<apps password>
SQL> @ $ZX_TOP/patch/115/sql/zxfcmigrateb.pls
5. Now re-start the failed worker for patch
But Theses patches require passcode which we getonly by logging an SR
Thanks
Vinay Varma -
Oracle Security Patch Error while applying --The filename, directory name,
Hello,
I am running into strange error while applying Oracle Security Patch 68 by using Opatch.
Supposedly, All the environment variables are set properly.
ACTIVE_STATE_PERL=true
DBMS_TYPE=ORA
dbs_ora_tnsname=YBQ
JAVA_HOME=C:\jdk1.3.1_10
OPATCH_DEBUG=TRUE
ORACLE_HOME=E:\oracle\ora92
ORACLE_SID=YBQ
Path=E:\oracle\OPatch;C:\jdk1.3.1_10\bin;E:\oracle\Perl\bin;E:\oracle\ora92\jre\1.4.2\bin\client;E:\oracle\ora92\jre\1.4.2\bin;E:\oracle\ora92\bin;C:\Program Files\Oracle\jre\1.3.1\bin;C:\Program Files\Oracle\jre\1.1.8\bin;C:\Program Files\Common Files\VERITAS Shared;\NetBackup\bin;C:\Program Files\Windows Resource Kits\Tools\;C:\Program Files\Support Tools\;C:\Windows\system32;C:\Windows;C:\Windows\System32\Wbem;E:\usr\sap\YBQ\SYS\exe\run
Installed Active Perl. latest version
downloaded Opatch 1.0.0.50
and the patch number 3738339
I went to that directory and run the command :
perl opatch.pl apply
It started of well.
OPatch version is: 1.0.0.0.50
Using ORACLE_HOME/oui to look up oui libs...
Oracle Home = E:\oracle\ora92
Location of Oracle Inventory = E:\oracle\ora92\inventory
Oracle Universal Installer shared library = E:\oracle\ora92\oui\lib\win32\oraInstaller.dll
Path to Java = "E:\oracle\ora92\jre\1.4.2\bin\java.exe"
Location of Oracle Inventory Pointer = N/A
Location of Oracle Universal Installer components = E:\oracle\ora92\oui
Required Jar File under Oracle Universal Installer = jlib\OraInstaller.jar
find under OH/oui/jlib
found OraInstaller.jar
Checking if this is a RAC system...
Accessing inventory... This may take up to 300 seconds.
(retry 10 times, delay 30 seconds each time)
System Command: ""E:\oracle\ora92\jre\1.4.2\bin\java.exe" -Dopatch.retry=10 -Dopatch.delay=30 -DTRACING.ENABLED=TRUE -DTRACING.LEVEL=2 -Dopatch.debug=true -classpath "E:\oracle\ora92\oui\jlib\OraInstaller.jar;E:\oracle\ora92\oui\jlib\srvm.jar;jlib\opatch.jar;E:\oracle\ora92\oui\jlib\xmlparserv2.jar;E:\oracle\ora92\oui\jlib\share.jar;.:E:\oracle\ora92\jlib\srvm.jar" opatch/O2O "e:\oracle\ora92" "E:\oracle\ora92\oui" opatch.pl 1.0.0.0.50"
Result:
----- DEBUG is ON -------
oracle.installer.startup_location will be set to E:\oracle\ora92\oui
oracle.installer.oui_loc will be set to E:\oracle\ora92\oui
oracle.installer.scratchPath will be set to /tmp
opatch.local_node_only is OFF
retryOption is ON: 10
delayOption is ON: 30
Few more stuff here .. not pasting the entire contents
System Command: ""E:\oracle\ora92\jre\1.4.2\bin\java.exe" -Dopatch.retry=10 -Dopatch.delay=30 -DTRACING.ENABLED=TRUE -DTRACING.LEVEL=2 -Dopatch.debug=true -classpath "E:\oracle\ora92\oui\jlib\OraInstaller.jar;E:\oracle\ora92\oui\jlib\srvm.jar;jlib\opatch.jar;E:\oracle\ora92\oui\jlib\xmlparserv2.jar;E:\oracle\ora92\oui\jlib\share.jar;." opatch/CheckConflict "E:\oracle\ora92\oui" "e:\oracle\ora92" opatch.pl 1.0.0.0.50 3738339 "3741539 3528282 3516951 3622875 3668572 3371796 3239873 3356103 3543125 3666502 2800494 2824035 2964252 3617042 3320622 3571233 3253770 3492040 3566469 3354470 3625370 3583686 3150750 3617519 3635177 3597640 3749394 3542588 3698501 2954891 2918138 3559212 3518909 3412818 3430832 3172282 3358490 3637624 3458446 3179637 2810394 3668224 3609791 3566813 3475932 2338704 3412136 3388633 3540576 3571226 3575743 2690205 3240280 3509265 3177513 3575747 3811906 3554319 3752406 3323435 " E:\3738339\etc\config\actions"
Result:
opatch.pl version: 1.0.0.0.50
Copyright (c) 2001-2004 Oracle Corporation. All Rights Reserved.
The filename, directory name, or volume label syntax is incorrect.
Error in executing Java program to check conflict
ERROR: OPatch failed during pre-reqs check.
Now there is no problem with executing the last java program in the same prompt by removing the first and the last double quote "
Please advise.
Thanks in advance.hi somnath,
this is the portal content management forum. for your database question please use the database forums:
http://forums.oracle.com/forums/index.jsp?cat=18
thanks,
christian -
Error while testing the Service Provider
Hi All,
I have developed a WebService model for Purchase Requisition scenario and followed all the steps of the Duet Developer Guide up to creating the SCL Business Object.
While testing the service on SAP side, when I execute the server proxy and in XML editor I passed the inpur values
Release Group :B1
Release Code : A1 for bapi BAPI_REQUISITION_GETITEMSREL,
Got the errors as below:
- <n0:StandardMessageFault xmlns:n0="http://myDuet.com/xi/PR">
- <standard>
<faultText>Proxy Class (generated)</faultText>
- <faultDetail>
<severity>error</severity>
<text>Non-Retriable Exception with message: The SAP system could not process your request. Contact your administrator</text>
<id>110(/IWFND/CM_COS)</id>
</faultDetail>
- <faultDetail>
<severity>error</severity>
<text>0 GSI implementations for Object Type 'ZPRGET_ITEMS_REL', Version 'ECC_604', Consumer ''</text>
<url>http://DUETBCCPL.bharathicement.com:8000/sap/xi/docu_apperror?ID=NA&OBJECT=%2fIWFND%2fCM_COS010&LANGUAGE=E&MSGV1=0&MSGV2=ZPRGET_ITEMS_REL&MSGV3=ECC_604</url>
<id>010(/IWFND/CM_COS)</id>
</faultDetail>
- <faultDetail>
<severity>error</severity>
<text>The SAP system could not process your request. Contact your administrator</text>
<url>http://DUETBCCPL.bharathicement.com:8000/sap/xi/docu_apperror?ID=NA&OBJECT=%2fIWFND%2fCOD011&LANGUAGE=E</url>
<id>011(/IWFND/COD)</id>
</faultDetail>
</standard>
</n0:StandardMessageFault>
And got the status message as
Call Failed
I tested the bapi in SAP Backend system, its working fine.
Can any body look into it where it is going wrong.
Thanks & Regards,
KrisHi all,
Issue has been resolved.
Thanks
Kris. -
ERROR WHILE DOING THE SERVICE ENTRY SHEET
Hi All,
I have budget INR 3000 & i created PR INR 2500 ,PO for the same amount INR 2500.Against the same i made INR 2000 down payment and it would as statistical in SAP. But while doing the service entry for same PO ,budget exceeded error coming.
I seen Program RFFMS009 program also all DP figures updated as statistical ,but while clearing the DP through F-54 system getting budget exceeded error message.
Kindly help me .we are in 4.7
Former budgeting
Rgds
ManisumaHi All,
There is problem in Field status varaint
Rgds
Suma -
Budget exceed error while unreleasing the service entry.
Hi experts,
My problem is the systm generating budget exceed error while unreleasing the entry sheet in current fiscal year.
Entry sheet is released in privious fiscal year. User want to reverse this in current year. All budget(actual/commitment) are carryforwarded to current year. While unreleasing the entry sheet, system throwing the budget exceed error. There is suficent budget in current fiscal year.
Request you to pl suggest what might be the cause of problem.
Regards
shrikantHi
Thanks for reply
For WBS element A-101.01
For year 2009
current budget is 100000
Distrubutable budget is 100000
Assigned budget is 100000
For year 2010
current budget is 300000
Distrubutable budget is 300000
Assigned budget is 200000
Service PO created in 2009 year for amount 20000/-. Service Entry sheet created and released in 2009 .Vendor invoice has not be generated. Error budget exceed is raised for year 2009 while reversing the service entry sheet in current posting date.(privious posting period /year closed). -
I keep getting a pop up of "error while trying to access the service" when I am trying to convert a pdf to a doc?
Hi snork8253,
Please let me know the exact workflow you are following when you get this error.
Are you trying to convert from within Reader or from Browser?
If from Reader then make sure you are signed in within Reader
Also try updating Reader to the latest v11.0.09 and check.
Regards,
Florence -
Error while applying the patch 9909156
while applying patch 9909156. I am getting jsp compilation errors in the patch log
[1634474] !!COMPILATION ERROR(0) ibeCRgpPartnerPriCreate.jsp:
this is similar MOS doc 579439.1 - Application Of Patch 5720979 Results In COMPILATION ERROR(0) ibeCOtdOrdCancelMain.jsp. Can you confirm please?
Patch 6128322 is for module iStore which is inactive on our system . Patch 5720979 was applied to the system (most likely as cumulative CPU). Can you confirm that given the module is inactive if we need to apply patch 6128322This is the error in the log file we are using 11.5.10.2
[1634474] !!COMPILATION ERROR(0) ibeCRgpBusinessCreate.jsp:
_ibeCRgpBusinessCreate.java:856: cannot find symbol
symbol : variable USERNAME_NOT_FOUND
location: class oracle.apps.ibe.um.UserManager
String usernameTestStatusCode=UserManager.USERNAME_NOT_FOUND;
^
_ibeCRgpBusinessCreate.java:858: cannot find symbol
symbol : variable SELF_REGISTRATION
location: class oracle.apps.ibe.um.UserManager
usernameTestStatusCode=UserManager.checkUsernameExists(usernameUpper, UserManager.SELF_REGISTRATION);
^
_ibeCRgpBusinessCreate.java:896: cannot find symbol
symbol : variable USERNAME_NOT_FOUND
location: class oracle.apps.ibe.um.UserManager
else if(ibeRegKnownUser==null && ! usernameTestStatusCode.equals(UserManager.USERNAME_NOT_FOUND)) -
Error while releasing the service order .
Hi,
After creating sales order from service order (ZOR3), when I am trying to release the service order by clicking on the green flag it is giving me error 'WBS for the Variant Service Line selected does not exist'.
Kindly advice a solution.
regards,
SDGWhat is the error message number ?? If it starts with "Z", then through some user exit, this control is applied which you have to check with your ABAPer on the coding.
thanks
G. Lakshmipathi -
Error while starting the service "oracle client cache"
hello everyone,
I keep getting an error message: while i'm starting the service "oracle
client cache "
The instruction at 0x7c911e58 referenced memory at 0x00000000. The
memory
could not be read.
please help me in rectifying this error ASAP
so that i can proceed further in my work
thanks in advanceHi
i have got the answer for this question, i updated the registry with the correct file path, and then closed the registry, the services.msc file is automatically updated with the correct path
and then started the CSService, then went to the OEM setup i clicked Retry buton, then it went through.
Thanks to all the viewers. -
Facing an error while restarting the services : Process Manager is not initialized.
while setting up the MDM environment I somehow messed up all the database connections.
Now im unable to start or stop the services properly.
Below is the error shown in the event viewer log for process MDM Ntier Process manager :
The description for Event ID ( 3 ) in Source ( MDM NTier Process Manager ) cannot be found. The local computer may not have the necessary registry information or message DLL files to display messages from a remote computer. You may be able to use the /AUXSOURCE= flag to retrieve this description; see Help and Support for details. The following information is part of the event: Exception Emdm_Exception with message 'Process Manager is not initialized.'.
Kindly help
I suspect this is because incorrect password for Engine login MDM_SYSTEM or incorrect configuration file (config.xml), However i may be wrong.As far as the "Process Manager is not initialized" error is concerned, we got the same error recently.
What we did was restart the DRM services on the server - The N-Tier Client and the Web-Publisher.
However, after doing it - we still got the error or DRM would not respond. On looking through it again, we saw that the Task Manager on the Server did not kill the DRM processes and so we did it manually. Then we restarted the services and it worked fine this time. See if this works for you - first kill all the services on the client sides and then on the server side, check for the client and server side process task manager and then restart the service. This worked for us, hopefully it works for you too.
-- Adi -
Error while creating the service pr
Dear All,
i have one Currency change while creating the PR issue
i have co code currenecy is USD while creating the material PR sysytem is
allowing to change the USD currency in AED Currency modifible condition where as if iam creating the Service pr system is default USD In hide mode but my user want to create the Service pr in AED.
So please help me ASAP.
Rgards
kishore EdagaliHi,
The currency in service PR/PO is fetched from service condition master,
Change the Currency in Deliv/Inv Tab, which will change the currency in service condition or manually change in the service condition master, so each time currency in PR needs not to be changed by user.
Regards,
Ahmad Farhan Khalid
Edited by: Ahmad Farhan Farhan on May 16, 2011 3:50 PM
Maybe you are looking for
-
Hi, In our company various versions (V7, R8.1 and R8.3) of Primavera being used in various locations. To bring all the location to a common platform, management has decided to implement / upgrade Primavera EPPM P6 R8.3 and also planned to integrate
-
Photosmart 6510 not printing in black
My 6510 recently stopped printing in black. (It is out of warranty.) I have tried most of the ideas posted in this forum, including multiple cartridge cleanings, deep cleanings, and various reboots. As with another poster, when I try to realign,
-
Upgrade to xorg 7.0 causes ati-driver panic
Not sure what is different with xorg 7.0 but ati-drivers cause a kernel panic after starting up X. Or is it because ATI hasn't released 7.0 drivers?
-
Clarification needed on the behaviour of count with null values
Hi friends, I am confused about the result given by the count aggregate function when dealing with null. Please can anybody clarify about that to me. Here is what i tried CREATE TABLE Demo ( a int); INSERT INTO Demo VALUES (1), (2), (NULL), (NULL); S
-
Can I use Java Card Development Kit 2.2.1 on Windows XP?
Can I use Java Card Development Kit 2.2.1 on Windows XP? If no, which kit supports XP?