[ethernet] eth0 connection does not run

My ethernet connection does not run! This is the reply from ifconfig:
$ ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:23:8B:FD:F5:48
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:47244640245 errors:283467841470 dropped:94489280490 overruns:47244640245 frame:236223201225
TX packets:47244640245 errors:188978560980 dropped:0 overruns:47244640245 carrier:94489280491
collisions:236223201225 txqueuelen:1000
RX bytes:47244640245 (45055.9 Mb) TX bytes:47244640245 (45055.9 Mb)
Interrupt:27
So my computer is connected, but all messages are dropped or in error.
Does somebody knows how to solve that problem, please.
Last edited by rafmav (2009-12-14 08:16:20)

Thanks for these replies! and fast!
I am not connected with a hub or a switch: it is a MODEM/ROUTER TrendNet TEW435BRM which goes well for DSL.
I cannot run dmesg for know... I will look in it later.
The computer is a new laptop (netbook type): Acer Aspire 1410 722G25n, Intel Celeron Mobile processor 723 (1.2 GHz, 800 MHz FSB, 1 Core, 64 Bits, 1M cache..., 10Watts max...), VGA: Intel GMA 4500MHD UP to 732 MB DVMT, 11.6" HD LED LCD
RAM: 2 GB memory, STORAGE: 250 GB HDD, WLAN: Acer Nplify 802.11b/g/Draft-N,
BATTERY: 6-cell 4400mAh Li-ion, SE: Windows Vista Home Premium OEM (EULA refuse by myself and deleted so not tested with it!).
$ lspci
01:00.0 Ethernet controller: Attansic Technology Corp. Device 1063 [1969:1063]
On the internet, some said that it is known as an Atheros AR8131 PCI-E Gigabit under Windows... and that the useful linux package is AR81Family-v1.0.0.10.tar.gz for them, but impossible to find on the internet (official site is down, the archive found elsewhere do not uncompress, etc...)
Linux is archlinux x86_64. The kernel driver in use is "atl1c" (on my ASUS eeepc beside, it is atl2 and runs well).
Ok, so:
- 1 read dmesg
- 2 try with another cable (the wire I used is old).
- 3 try with another kernel driver (have to find it)
- 4 send back the computer to be repaired!
Bye
Last edited by rafmav (2009-12-14 13:17:21)

Similar Messages

Cisco Connect does not run with Mac OSX Mountain Lion (10.8.2)

When I first installed Cisco Connect that came with my E1500 router, I was running Mac OSX Snow Leopard (10.7) and it worked fine. I upgraded my OSX to Mountain Lion and now when I start Cisco Connect, I get:
Unsupported operating system
The router software supports these operating systems:
- Mac OS X 10.5.8 or later
- Mac OS X 10.6.1 or later
- Mac OS X 10.7 or later
I saw some other thread/info/download on Cisco Connect with Lion (10.7) but nothing for Moutain Lion (10.8) - is there a fix forthcoming?
Thanks
Gary

All i want to do is disable the guest function through cisco. i live in an apartment and everyone logs into my guest account. i was at my neighbours and they were laughing saying they done need to subscribe for the internet cause they just log onto local wi fi. and mine is one of them. i dont know if that'll slow down my internet with so many people using it. but all i want to do is just avoid it all together and get rid of it. but in this case i am having the same problem as all of you. to disable the guest function you need to go through cisco connect and it is not compatible with mac osx mountain lion. grrrrrrr

I m working in an organization where web-sense is installed to block all irrelevant sites, i have installed itunes but it does not run a window pops up with message 'itunes is not connected to the network' can anyone help me out?

i m working in an organization where web-sense is installed to block all irrelevant sites, i have installed itunes but it does not run a window pops up with message 'itunes is not connected to the network' can anyone help me out?

There's a whole lot to read in your post, and frankly I have not read it all.
Having said that, this troubleshooting guide should help:
http://support.apple.com/kb/TS1538
In particular, pay attention to the mobile device support sections near the bottom, assuming you have already done the items above it.

User gets "This network connection does not exist" when she tries to log on to Terminal Server (2008 R2)

User gets "This network connection does not exist" when she tryes to log on to Terminal Server (2008 R2)
I got more than 100 users. Shes the only one getting is. We tried four computers (All Windows 7 Pro)
Nothing useful in event viewer to mention.

Hi,
Thank you for posting in Windows Server Forum.
Does that user able to login previously?
From your comment, it seems that there is some permission issue with that user. As you have checked that user with different system also. Please check that user is added under “Remote Desktop User” local group and also allowed “Allow log on through
Remote Desktop service” permission under group policy. Also please check that when user tries to login it uses “Domainname\Username” format.
In addition for a try, also check by disabling firewall on one particular system.
To add users and groups to the Remote Desktop Users group by using Local Users and Groups snap-in:
1. Click Start > Administrative Tools, Open Computer Management.
2. In the console tree, click the Local Users and Groups node.
3. In the details pane, double-click the Groups folder.
4. Double-click Remote Desktop Users, and then click
Add.
5. In the Select Users dialog box, click Locations to specify the search location.
6. Click Object Types to specify the types of objects you want to search for.
7. Type the name you want to add in the Enter the object names to select (examples) box.
8. Click Check Names.
When the name is located, click OK.
More information:
Remote Desktop disconnected or can’t connect to remote computer or to Remote Desktop server (Terminal Server) that is running Windows Server 2008 R2
http://support.microsoft.com/kb/2477176/en-us
Hope it helps!
Thanks,
Dharmesh

REPORT DOES NOT RUN CORRECTLY , URGENT PLEASE HELP

Hi,
I am trying to run a report from visul basic screen, but it does not run correctly. Here is how I am running the report. There is a screen developed in VB This screen prompts the user for user id and password. Once it gets that, it connects to the oracle database and pulls out a column from a table. And passes that value as a parameter to the report. Now I am calling the the report for each individual value . There are 21 value being pulled out of the database and it invokes the report 21 times. So there are 21 report engines gets started. Is there a better way to do that ? Secondly when I pass the parameter , some parameters does not pass correctly I guess , because its not generating any out put . Like out of 21 may be 10 or 11 reports gets generated correctly but rest of the reports are blank. I debug the screen i saw that the parameter value is correct, everything seems good. But still the reports are comming blank. Any Idea why it is so ? The command line that i am using in VB screen is
Shell "C:\progra~1\ora95_2\bin\rwrun60.exe P:\Business_Analysis_&_Reporting_Tool\Test_REPORT_Templates\STORE_TYPES\Baby_Distribution_Report.Rdf USERID=" & UID & "/" & PWD & "@cposp201 DESFORMAT=PDF DESTYPE=FILE DESNAME=" & txtPath.Text & Replace(strName, " ", "_") & ".PDF BRND='" & adoRecBrand!Brand & "' PRINTJOB=NO PARAMFORM=NO"
In the above command " adoRecBrand!Brand " is the parameter thats being passed. This is actually a recordset and brand is the column in it. When I debug the screen , I see the value also there. But the report comes out blank. Please help. This is urgent.
Thanks
Feroz

The way you call reports is not scalable. If you have 100 records come back from database, you would end up launch 100 engines at the same times, which probably will blow up your machine. You should use oracle reports server to do that. You can either use rwcli60 to submit the job to reports server, or invoke rwcgi60 from URL.
I am afraid some of reports engine failed to start and you get nothing back in your case.
After switch to use reports server achitecture, if you still see some report is blank in your application, then you can run that report with that special set of parameters manually and see if any problem with the report itself.
Hope this helps.
Thanks,
-Shaun

Add does not run with sql server 2008

Hi all,
My add on in the development environment does not run with SQL SERVER 2008. It ran well with SQL Server 2005 and sap b1 2207 B.
On executing the project file system throws an error "YOU ARE NOT CONNECTED TO THE COMPANY"
we are trying this scenario on a test machine where SAP B1 2007B with temporary license for one month and SQL server 2008
is installed.
Help needed.
Thanking you
Pradnya

Hi Use this
Dim i as integer
i=oCompany.Connect()
if i<> 0 Then
msgbox(ocompany.GetLastErrorDescription ())
end if
the you will get the error description also use try catch wherever necessary
Alternatively you can use
Dim SboGuiApi As SAPbouiCOM.SboGuiApi
Dim sConnectionString As String
Set SboGuiApi = New SAPbouiCOM.SboGuiApi
sConnectionString = Command
SboGuiApi.Connect sConnectionString
Set SBO_Application = SboGuiApi.GetApplication()
Set ocompany = New SAPbobsCOM.Company 'initialate DI company object
ocompany = SBO_Application.Company.GetDICompany
HTH,
Atul

Javaee6 sample does not run on remote GF 3.1

I installed javaee6 with samples:
java_ee_sdk-6u2-jdk-linux-x64-ml.sh
I can run "automatic-timer" sample properly, when GF 3.1 runs on localhost.
If GF 3.1 runs on a remte host.
I set the remote GF 3.1 in bp-project/build.properties:
javaee.server.name=192.168.1.101
Now automatic-timer sample does not run:
[java] Waiting for the timer to expire
[java] Logged timeouts :
[java] org.omg.CORBA.COMM_FAILURE: FINE: IOP00410001: Connection failure: socketType: IIOP_CLEAR_TEXT; hostname: localhost; port: 3700 vmcid: OMG minor code: 1 completed: No
[java]      at sun.reflect.GeneratedConstructorAccessor30.newInstance(Unknown Source)
[java]      at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27)
[java]      at java.lang.reflect.Constructor.newInstance(Constructor.java:513)
[java]      at com.sun.corba.ee.spi.orbutil.logex.corba.CorbaExtension.makeException(CorbaExtension.java:248)
[java]      at com.sun.corba.ee.spi.orbutil.logex.corba.CorbaExtension.makeException(CorbaExtension.java:95)
[java]      at com.sun.corba.ee.spi.orbutil.logex.WrapperGenerator.handleFullLogging(WrapperGenerator.java:387)
[java]      at com.sun.corba.ee.spi.orbutil.logex.WrapperGenerator.access$400(WrapperGenerator.java:107)
[java]      at com.sun.corba.ee.spi.orbutil.logex.WrapperGenerator$2.invoke(WrapperGenerator.java:511)
[java]      at com.sun.corba.ee.spi.orbutil.proxy.CompositeInvocationHandlerImpl.invoke(CompositeInvocationHandlerImpl.java:99)
[java]      at $Proxy26.connectFailure(Unknown Source)
[java]      at com.sun.corba.ee.impl.transport.SocketOrChannelConnectionImpl.<init>(SocketOrChannelConnectionImpl.java:257)
[java]      at com.sun.corba.ee.impl.transport.SocketOrChannelConnectionImpl.<init>(SocketOrChannelConnectionImpl.java:270)
[java]      at com.sun.corba.ee.impl.transport.SocketOrChannelContactInfoImpl.createConnection(SocketOrChannelContactInfoImpl.java:129)
[java]      at com.sun.corba.ee.impl.protocol.CorbaClientRequestDispatcherImpl.beginRequest(CorbaClientRequestDispatcherImpl.java:223)
[java]      at com.sun.corba.ee.impl.protocol.CorbaClientDelegateImpl.request(CorbaClientDelegateImpl.java:228)
[java]      at com.sun.corba.ee.impl.protocol.CorbaClientDelegateImpl.is_a(CorbaClientDelegateImpl.java:393)
[java]      at org.omg.CORBA.portable.ObjectImpl._is_a(ObjectImpl.java:112)
[java]      at org.omg.CosNaming.NamingContextHelper.narrow(NamingContextHelper.java:69)
[java]      at com.sun.enterprise.naming.impl.SerialContext$ProviderCacheKey.getNameService(SerialContext.java:1241)
[java]      at com.sun.enterprise.naming.impl.SerialContext.getRemoteProvider(SerialContext.java:411)
[java]      at com.sun.enterprise.naming.impl.SerialContext.getProvider(SerialContext.java:347)
[java]      at com.sun.enterprise.naming.impl.SerialContext.lookup(SerialContext.java:504)
[java]      at com.sun.enterprise.naming.impl.SerialContext.lookup(SerialContext.java:455)
[java]      at javax.naming.InitialContext.lookup(InitialContext.java:392)
[java]      at enterprise.automatic_timer_client.AutomaticTimerJavaClient.getRecords(AutomaticTimerJavaClient.java:64)
[java]      at enterprise.automatic_timer_client.AutomaticTimerJavaClient.main(AutomaticTimerJavaClient.java:53)
[java] Caused by: java.lang.RuntimeException: java.net.ConnectException: Connection refused
[java]      at org.glassfish.enterprise.iiop.impl.IIOPSSLSocketFactory.createSocket(IIOPSSLSocketFactory.java:340)
[java]      at com.sun.corba.ee.impl.transport.SocketOrChannelConnectionImpl.<init>(SocketOrChannelConnectionImpl.java:242)
[java]      ... 15 more
[java] Caused by: java.net.ConnectException: Connection refused
[java]      at sun.nio.ch.Net.connect(Native Method)
[java]      at sun.nio.ch.SocketChannelImpl.connect(SocketChannelImpl.java:500)
[java]      at com.sun.corba.ee.impl.orbutil.ORBUtility.openSocketChannel(ORBUtility.java:110)
[java]      at org.glassfish.enterprise.iiop.impl.IIOPSSLSocketFactory.createSocket(IIOPSSLSocketFactory.java:325)
[java]      ... 16 more
[java] javax.naming.NamingException: Lookup failed for 'java:global/automatic-timer-ejb/StatelessSessionBean' in SerialContext[myEnv={java.naming.factory.initial=com.sun.enterprise.naming.impl.SerialInitContextFactory, java.naming.factory.url.pkgs=com.sun.enterprise.naming, java.naming.factory.state=com.sun.corba.ee.impl.presentation.rmi.JNDIStateFactoryImpl} [Root exception is javax.naming.NamingException: Unable to acquire SerialContextProvider for SerialContext[myEnv={java.naming.factory.initial=com.sun.enterprise.naming.impl.SerialInitContextFactory, java.naming.factory.url.pkgs=com.sun.enterprise.naming, java.naming.factory.state=com.sun.corba.ee.impl.presentation.rmi.JNDIStateFactoryImpl} [Root exception is org.omg.CORBA.COMM_FAILURE: FINE: IOP00410001: Connection failure: socketType: IIOP_CLEAR_TEXT; hostname: localhost; port: 3700 vmcid: OMG minor code: 1 completed: No]]
[java]      at com.sun.enterprise.naming.impl.SerialContext.lookup(SerialContext.java:518)
[java]      at com.sun.enterprise.naming.impl.SerialContext.lookup(SerialContext.java:455)
[java]      at javax.naming.InitialContext.lookup(InitialContext.java:392)
[java]      at enterprise.automatic_timer_client.AutomaticTimerJavaClient.getRecords(AutomaticTimerJavaClient.java:64)
[java]      at enterprise.automatic_timer_client.AutomaticTimerJavaClient.main(AutomaticTimerJavaClient.java:53)
[java] Caused by: javax.naming.NamingException: Unable to acquire SerialContextProvider for SerialContext[myEnv={java.naming.factory.initial=com.sun.enterprise.naming.impl.SerialInitContextFactory, java.naming.factory.url.pkgs=com.sun.enterprise.naming, java.naming.factory.state=com.sun.corba.ee.impl.presentation.rmi.JNDIStateFactoryImpl} [Root exception is org.omg.CORBA.COMM_FAILURE: FINE: IOP00410001: Connection failure: socketType: IIOP_CLEAR_TEXT; hostname: localhost; port: 3700 vmcid: OMG minor code: 1 completed: No]
[java]      at com.sun.enterprise.naming.impl.SerialContext.getProvider(SerialContext.java:352)
[java]      at com.sun.enterprise.naming.impl.SerialContext.lookup(SerialContext.java:504)
[java]      ... 4 more
[java] Caused by: org.omg.CORBA.COMM_FAILURE: FINE: IOP00410001: Connection failure: socketType: IIOP_CLEAR_TEXT; hostname: localhost; port: 3700 vmcid: OMG minor code: 1 completed: No
[java]      at sun.reflect.GeneratedConstructorAccessor30.newInstance(Unknown Source)
[java]      at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27)
[java]      at java.lang.reflect.Constructor.newInstance(Constructor.java:513)
[java]      at com.sun.corba.ee.spi.orbutil.logex.corba.CorbaExtension.makeException(CorbaExtension.java:248)
[java]      at com.sun.corba.ee.spi.orbutil.logex.corba.CorbaExtension.makeException(CorbaExtension.java:95)
[java]      at com.sun.corba.ee.spi.orbutil.logex.WrapperGenerator.handleFullLogging(WrapperGenerator.java:387)
[java]      at com.sun.corba.ee.spi.orbutil.logex.WrapperGenerator.access$400(WrapperGenerator.java:107)
[java]      at com.sun.corba.ee.spi.orbutil.logex.WrapperGenerator$2.invoke(WrapperGenerator.java:511)
[java]      at com.sun.corba.ee.spi.orbutil.proxy.CompositeInvocationHandlerImpl.invoke(CompositeInvocationHandlerImpl.java:99)
[java]      at $Proxy26.connectFailure(Unknown Source)
[java]      at com.sun.corba.ee.impl.transport.SocketOrChannelConnectionImpl.<init>(SocketOrChannelConnectionImpl.java:257)
[java]      at com.sun.corba.ee.impl.transport.SocketOrChannelConnectionImpl.<init>(SocketOrChannelConnectionImpl.java:270)
[java]      at com.sun.corba.ee.impl.transport.SocketOrChannelContactInfoImpl.createConnection(SocketOrChannelContactInfoImpl.java:129)
[java]      at com.sun.corba.ee.impl.protocol.CorbaClientRequestDispatcherImpl.beginRequest(CorbaClientRequestDispatcherImpl.java:223)
[java]      at com.sun.corba.ee.impl.protocol.CorbaClientDelegateImpl.request(CorbaClientDelegateImpl.java:228)
[java]      at com.sun.corba.ee.impl.protocol.CorbaClientDelegateImpl.is_a(CorbaClientDelegateImpl.java:393)
[java]      at org.omg.CORBA.portable.ObjectImpl._is_a(ObjectImpl.java:112)
[java]      at org.omg.CosNaming.NamingContextHelper.narrow(NamingContextHelper.java:69)
[java]      at com.sun.enterprise.naming.impl.SerialContext$ProviderCacheKey.getNameService(SerialContext.java:1241)
[java]      at com.sun.enterprise.naming.impl.SerialContext.getRemoteProvider(SerialContext.java:411)
[java]      at com.sun.enterprise.naming.impl.SerialContext.getProvider(SerialContext.java:347)
[java]      ... 5 more
[java] Caused by: java.lang.RuntimeException: java.net.ConnectException: Connection refused
[java]      at org.glassfish.enterprise.iiop.impl.IIOPSSLSocketFactory.createSocket(IIOPSSLSocketFactory.java:340)
[java]      at com.sun.corba.ee.impl.transport.SocketOrChannelConnectionImpl.<init>(SocketOrChannelConnectionImpl.java:242)
[java]      ... 15 more
[java] Caused by: java.net.ConnectException: Connection refused
[java]      at sun.nio.ch.Net.connect(Native Method)
[java]      at sun.nio.ch.SocketChannelImpl.connect(SocketChannelImpl.java:500)
[java]      at com.sun.corba.ee.impl.orbutil.ORBUtility.openSocketChannel(ORBUtility.java:110)
[java]      at org.glassfish.enterprise.iiop.impl.IIOPSSLSocketFactory.createSocket(IIOPSSLSocketFactory.java:325)
[java]      ... 16 more
[java] Exception in thread "main" java.lang.NullPointerException
[java]      at enterprise.automatic_timer_client.AutomaticTimerJavaClient.main(AutomaticTimerJavaClient.java:54)
Why does it use localhost instead of 192.168.1.106 ?
How can I run the sample against a remote GF 3.1 ?
Thank you

I got solution:
Re: Can't access remote EJBs (GF3.1)
I followed the instructions from http://www.java.net/node/676636
and changed "/etc/hosts" file:
1) commented out the "internal" IP addresses in the first two lines
2) and added a the external IP address
#127.0.0.1 localhost
#127.0.1.1 lennyserver
192.168.0.202 lennyserver
The following lines are desirable for IPv6 capable hosts
::1 localhost ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
ff02::3 ip6-allhosts
Now the InitialContext.lookup() can find the bean.

IBook does not run on battery

My Ibook does not run on battery when it reaches 48%. It just shutsdown with no warnings. I have to connect the AC adapter to work if i disconnect it the ibook just shuts down. I have to waut until it reaches 100% and then i take the AC adapter. I book shuts down and after i turn it on with out the AC and it stays running on bat until the 48%. Then i have to go through everything again.

Jobbaman wrote:
Till now my battery has been working perfectly. The machine is about 1 year old and I use it heavily for my work. I prefer to unplug my battery when it's full, and use it till it go's to sleep before plugging it in again. This results in a very high Cycle count (453) but a still perfectly working battery (98% according to CoconutBattery), I can use the machine for about 4 hours on a full battery.
The amperage would be 0 since your battery is not in a charge cycle.
Part of your problem could honestly be your cycle count and method of caring for your battery. If you check some of the research about Li_ion batteries this is the worse way to use it. Li-Ion batteries work best with little charges. Deep cycling Li-Ion can kill the cells. There is no good reason to charge the battery and then use it as you have been doing. This just kills your battery for no reason. The MacBook is designed to cut the charge off when the battery is full and it does not hurt the battery to lie idle like this. The method you're using can prematurely kill your battery.
Either the battery has a problem that is not showing on you readings or the battery circuit is fried. Do you know someone that has a MacBook or live near an Apple store so you can test your battery on a known good MacBook. Or you could try one of their batteries in it.

The connection does not exist

Hi Guys,
We are trying to extract data from AS/400 TO ORACLE through ODI Interfaces,most of the time they wilkl work well.
Sometimes suddenly in the middle of the load it will fails with an error message 'The connection does not exist'
The following is the full error message any help here guys?It will work perfectly when we run it again:-
-99999 : 08003 : java.sql.SQLException: The connection does not exist.
java.sql.SQLException: The connection does not exist.
at com.ibm.as400.access.JDError.throwSQLException(JDError.java:389)
at com.ibm.as400.access.AS400JDBCConnection.checkOpen(AS400JDBCConnection.java:418)
at com.ibm.as400.access.AS400JDBCConnection.send(AS400JDBCConnection.java:2541)
at com.ibm.as400.access.AS400JDBCConnection.send(AS400JDBCConnection.java:2516)
at com.ibm.as400.access.JDCursor.close(JDCursor.java:119)
at com.ibm.as400.access.AS400JDBCStatement.notifyClose(AS400JDBCStatement.java:3272)
at com.ibm.as400.access.AS400JDBCResultSet.close(AS400JDBCResultSet.java:470)
at oracle.odi.runtime.agent.execution.sql.concurrent.FastJDBCRecordSet.close(FastJDBCRecordSet.java:124)
at oracle.odi.runtime.agent.execution.DataMovementTaskExecutionHandler.handleTask(DataMovementTaskExecutionHandler.java:103)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.processTask(SnpSessTaskSql.java:2913)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTask(SnpSessTaskSql.java:2625)
at com.sunopsis.dwg.dbobj.SnpSessStep.treatAttachedTasks(SnpSessStep.java:558)
at com.sunopsis.dwg.dbobj.SnpSessStep.treatSessStep(SnpSessStep.java:464)
at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java:2093)
at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java:1889)
at oracle.odi.runtime.agent.processor.impl.StartScenRequestProcessor$2.doAction(StartScenRequestProcessor.java:580)
at oracle.odi.core.persistence.dwgobject.DwgObjectTemplate.execute(DwgObjectTemplate.java:216)
at oracle.odi.runtime.agent.processor.impl.StartScenRequestProcessor.doProcessStartScenTask(StartScenRequestProcessor.java:513)
at oracle.odi.runtime.agent.processor.impl.StartScenRequestProcessor$StartScenTask.doExecute(StartScenRequestProcessor.java:1066)
at oracle.odi.runtime.agent.processor.task.AgentTask.execute(AgentTask.java:126)
at oracle.odi.runtime.agent.support.DefaultAgentTaskExecutor$1.run(DefaultAgentTaskExecutor.java:49)
at org.springframework.core.task.SyncTaskExecutor.execute(SyncTaskExecutor.java:49)
at oracle.odi.runtime.agent.support.DefaultAgentTaskExecutor.executeAgentTask(DefaultAgentTaskExecutor.java:41)
at oracle.odi.runtime.agent.processor.TaskExecutorAgentRequestProcessor.doExecuteAgentTask(TaskExecutorAgentRequestProcessor.java:92)
at oracle.odi.runtime.agent.processor.TaskExecutorAgentRequestProcessor.process(TaskExecutorAgentRequestProcessor.java:83)
at oracle.odi.runtime.agent.RuntimeAgent.startScenario(RuntimeAgent.java:433)
at oracle.odi.StartScen.run(StartScen.java:229)
at oracle.odi.StartScen.main(StartScen.java:343)

Hi,
In which step, it is giving error. did you check the source and target connection properly when this problem arrives.
Thanks

Wi-fi connection does not auto connect on 21.5-inch mid 2010 imac help?

Wi-fi connection does not auto connect on 21.5-inch mid 2010 imac running OS X 10.8.3 (12D78) help? My wife's imac with OS X 10.6.8 has no problem getting on wi-fi automatically as well as my Ipad 2 running iOS 6.1.2

If you get a green light then you did not do a factory reset - you must disconnect all wires and follow the instructions above - you will end up with the Extreme blinking yellow - then use the Airport utility to set up the Extreme - you can put in your own names for the network, device etc. - when it comes to the passwords you can use ones of your own choice - it is not asking for the old one - if it is then it was not reset completely - try to reset again if necessary - it may take more than one try - if it still asks for a password then use "public" - it is the default - once you have set it up with your new information, and you have a green light, test the connection with your computer - if you can access the internet then you are all set - then try to a use the Apple TV with the new password - if the computer still asks for a password, then it is asking for the computer password and not the extreme or network password - I can't help you with that - you would have to ask that question on the iMac discussion group.

ICal does not run one event that has a Applescript attached to it. 24u?

I have a number of reoccurring events in iCal that run a Applescript. Tow of them refuses to run. I have tried it as a Applescript and saved it as a run only and neither works (the script run fine if I test them by hand).
so I thought I have a look in the log and found this 24u information.
can anybody help out here? I am not sure why it appears, if it is good or bad, how to fix it and if it is at all realted to my problem. Other scripts seem to run well, it is this one and an other one that do not get activated by iCall.
They run on a MM running 10.6.8, iCall 4.0.4 (1395.7)
Thanks.
Log today:
19/09/2011 07:00:00          iCal Helper[211]          Error loading /Library/ScriptingAdditions/24U Appearance OSAX.osax/Contents/MacOS/24U Appearance OSAX: dlopen(/Library/ScriptingAdditions/24U Appearance OSAX.osax/Contents/MacOS/24U Appearance OSAX, 262): no suitable image found. Did find:
          /Library/ScriptingAdditions/24U Appearance OSAX.osax/Contents/MacOS/24U Appearance OSAX: mach-o, but wrong architecture
19/09/2011 07:00:00          [0x0-0x12012].com.apple.iCal.helper[211]          iCal Helper: OpenScripting.framework - scripting addition "/Library/ScriptingAdditions/24U Appearance OSAX.osax" declares no loadable handlers.
19/09/2011 07:45:01          iCal Helper[317]          Error loading /Library/ScriptingAdditions/24U Appearance OSAX.osax/Contents/MacOS/24U Appearance OSAX: dlopen(/Library/ScriptingAdditions/24U Appearance OSAX.osax/Contents/MacOS/24U Appearance OSAX, 262): no suitable image found. Did find:
          /Library/ScriptingAdditions/24U Appearance OSAX.osax/Contents/MacOS/24U Appearance OSAX: mach-o, but wrong architecture
19/09/2011 07:45:01          [0x0-0x28028].com.apple.iCal.helper[317]          iCal Helper: OpenScripting.framework - scripting addition "/Library/ScriptingAdditions/24U Appearance OSAX.osax" declares no loadable handlers.
19/09/2011 14:30:02          iCal Helper[1019]          Error loading /Library/ScriptingAdditions/24U Appearance OSAX.osax/Contents/MacOS/24U Appearance OSAX: dlopen(/Library/ScriptingAdditions/24U Appearance OSAX.osax/Contents/MacOS/24U Appearance OSAX, 262): no suitable image found. Did find:
          /Library/ScriptingAdditions/24U Appearance OSAX.osax/Contents/MacOS/24U Appearance OSAX: mach-o, but wrong architecture
19/09/2011 14:30:02          [0x0-0x73073].com.apple.iCal.helper[1019]          iCal Helper: OpenScripting.framework - scripting addition "/Library/ScriptingAdditions/24U Appearance OSAX.osax" declares no loadable handlers.

Hi,
It looks like the version of 24U's Appearance OSAX you have installed does not run on Lion.
I would contact the developer to see if they have a version that does yet. See http://www.24usoftware.com/AppearanceOSAX
Alternatively you could look to see if the Applescript really needs to use it.
Best wishes
John M
Edit: If you are running Snow Leopard, I think you may need to make the application "iCal Helper" (which you'll find in iCal's application package) run as 32 bit. I'd also suggest you check this with 24U.

Premiere elements 12, new installation, serial no. accepted, installation completed and new started, but does not run. I get following msg-box: "LoadLibrary failed with error 126: Das angegebene Modul wurde nicht gefunden."

premiere elements 12, new installation, serial no. accepted, installation completed and new started, but does not run. I get following msg-box: "LoadLibrary failed with error 126: Das angegebene Modul wurde nicht gefunden." Installation in German Language on WIN7 professional 64bit, Samsung SSD. What can I do to run that program?

Jurgen Freund
Premiere Elements 12 on Window 7 64 bit. What video card/graphics card does your computer use - AMD Radeon?
I have found this YouTube video on the subject of Error 126 with details for resolving the problem.
How to fix the ERROR 126 when you open OpenGL programs - YouTube
The link was contributed in an old 2013 thread here by the ID danneomarre (see post 6 of the following thread)
LoadLibrary failed with error 126: cant find the required
Please let us know if that worked for you.
Thank you.
ATR
Add On...When all is OK and working, please update 12 to 12.1 Update using an opened project's Help Menu/Update.

Adobe Connect does not show tool pointer/cursor when sharing Photoshop...

I am an online instructor and one of the courses I teach is a Photoshop course. Each week I host a Live Lecture session where we use Adobe Connect to demonstrate techniques and tools in Photoshop CS6.
I am receiving several complaints from students because Adobe Connect does not correctly show my cursor/pointer when it changes for each tool in Photoshop. All the students see is an arrow with a small icon of a face/monitor.
This is confusing to the students, because I am trying to demonstrate how to use a tool and they are unable to see the actual tool. For example, when I select the brush tool - they should be able to see the brush circle as the cursor. I then demonstrate how to resize the brush - but they cannot see it. Another example is any of the healing/cloning tools. If I select the healing brush tool, they cannot see the circle (brush). I then demonstrate how to record a healing point by selecting the Option (alt) key - but again the students cannot see the pointer change to the crosshairs to record the healing point - as all they see is the arrow with icon at all times.
Students are complaining that they are not able to comprehend what I am demonstrating because they are not able to get the full affect of the demonstration without seeing it how it should be. Prior to switching to Adobe Connect, we used WebEx - which showed the students everything correctly as I was demonstrating it. I was amazed to learn that Adobe Connect does not show everything - especially since I am using another Adobe program within Adobe Connect - you would think they would be fully compatible and able to show everything.
Thank you

I just saw this option for the first time last week. Very exciting to see it finally in Connect! There is a small amount of lag for the viewers, but nothing that can't be compensated for.

My Firefox version is 13.0.1, I use Windows Seven 64-bit, when I click on Firefox, but the program does not run! But Firefox is seen in the list of Windows proc

My Firefox version is 13.0.1, I use Windows Seven 64-bit, when I click on Firefox, but the program does not run! But Firefox is seen in the list of Windows processes, while Firefox does not run.
I manually deleted Firefox from the list once I have Windows processing.
And when I clicked on Firefox, Firefox will open quickly and easily.
Firefox process in Windows Processes names list called "firefox.exe * 32" is.
Please try to solve my problem, my problem is how to solve?

Hi, are you saying that you start Firefox and it stalls -- you can see it in the Task Manager but it never displays -- but if you kill that process and start Firefox again it starts up properly that second time?
If you look at the statistics available in the Task Manager's processes tab such as bytes read or other bytes, can you see whether Firefox is doing anything at all? ''Note: You might need to add columns if your Processes tab isn't set up to display statistics. You can do that from the View menu.''
You might already have seen these troubleshooting articles. If not, does anything here help:
* [[Firefox won't start - find solutions]]
* [[Firefox hangs or is not responding - How to fix]]

Lightroom 5.6 does not run following latest CC Photoshop 2014 and Bridge updates

I am running Creative Cloud Photography on OSX 10.9.4. Yesterday I updated Photoshop 2014 and Bridge using the CC desktop app as prompted by CC. Since then Lightroom does not run. When I open it the blue intro screen flashes up for less than a second. To try and recover I have uninstalled Lightroom (5.6) and re-installed it several times using both the CC app and directly from the Adobe website. The result is always the same. I can find nothing about this on Adobe Support although I can find others who have had the same symptoms on a web search. Their solution was to re-install Lightroom from the web site but that hasn't worked for me. I had Lightroom installed before I went to CC and before CC included Lightroom in the Photography package. Does anyone understand this issue and can you please advise me what to try next? Many thanks.

Okay, Solution 1 from this link Error "Unable to start correctly - 0Xc00007b" fixed it for me. But now it's asking me for the serial number which I can't find anywhere... shouldn't that go without with the cloud?

[ethernet] eth0 connection does not run

Similar Messages

Maybe you are looking for