Event ID 1135 When Node Paused

I have a three node Server 2012 cluster with Hyper-V running on the cluster. When I pause a server, and then restart it, I am getting Event ID 1135:
Cluster node 'COTTONMILL' was removed from the active failover cluster membership. The Cluster service on this node may have stopped. This could also be due to the node having lost communication with other active nodes in the failover cluster. Run the Validate
a Configuration wizard to check your network configuration. If the condition persists, check for hardware or software errors related to the network adapters on this node. Also check for failures in any other network components to which the node is connected
such as hubs, switches, or bridges.
and also Event ID 1177:
The Cluster service is shutting down because quorum was lost. This could be due to the loss of network connectivity between some or all nodes in the cluster, or a failover of the witness disk.
Run the Validate a Configuration wizard to check your network configuration. If the condition persists, check for hardware or software errors related to the network adapter. Also check for failures in any other network components to which the node is connected
such as hubs, switches, or bridges.
All of my virtual servers stay up though.
Quorum is set at NodeMajority with no witness.
Should I be getting these errors when I pause one node to do maintenance and the other two nodes are running? Thanks.

Hi,
The 1135 event will be logged on all nodes in the Cluster except for the node that was removed. The reason for this event is because one of the nodes in the Cluster marked
that node as down. It then notifies all of the other nodes of the event. When the nodes are notified, they discontinue and tear down their heartbeat connections to the downed node.
And the 1177 event may cause by your restart, you can refer the following article for the more detail reason:
Having a problem with nodes being removed from active Failover Cluster membership?
http://blogs.technet.com/b/askcore/archive/2012/02/08/having-a-problem-with-nodes-being-removed-from-active-failover-cluster-membership.aspx
Event ID 1177 — Quorum and Connectivity Needed for Quorum
http://technet.microsoft.com/en-us/library/cc773498(v=ws.10).aspx
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Similar Messages

Auditing cluster events - can we see who paused a node?

Hello
We have a 2 node cluster with an active passive configuration - running server 2008 r2 / SQL 2008
We had an issue today where one of the nodes was paused; and the active node had an issue with the cluster services, which ended up taking the resources offline (as you would expect)
I fixed the issue via resuming the paused node; failing over the resources and restarting the cluster services - and bringing the resources back online
Im trying to find out the 'why' behind the inactive node being left paused, as such i want to know if there are any events logged when a node is paused (i.e. a security event)
I did a test scenario on the server, I paused the node but nothing is logged in any of the usual event places. Does the inactive node have to be left paused for a certian period of time before the cluster events / cluster operations log start logging things?
Any help would be appreciated

Hello,
After checking the cluster related logs and systme/application logs, it appears that there're no logs recorded when pausing a cluster node.
And generally, pausing a node is usually done when applying software updates to the node, where the recommended sequence is to move all services and applications off of the node, pause the node, then apply software updates to the node.
You may refer to the following link for more information.
Pause or Resume a Node in a Failover Cluster
http://technet.microsoft.com/en-us/library/cc731291.aspx
Best Regards,
Sophia Sun
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.
Thanks - I was afraid of that
I know that pausing a node is only usually done when updating / patching etc, but windows updates fore this cluster are not done whatsoever - which put me down this path to begin with
Appreciate everyones input on this

OnMouseClicked event with overlapping custom nodes

I'm having a bit of an issue with overlapping nodes.
Essentially what I have are rectangular shaped custom nodes which, when an onMouseEntered event occurs, has an extended set of icons that fade in that are located on the above top right portion of the node. If I may use ASCII to illustrate :)
X
[ MyCustomNode ]
+(Blank spaces don't work too well so let's pretend the X is sitting on top of the node on the upper left corner)+
The X is an icon that simply deletes the node.
The problem occurs when the nodes are overlapping (i.e. one above the other, where the X icon is overlapping with the node above it). When I click on the X, the onMouseClicked event fires for the node above.
I've tried mucking around with disabling the node and using toFront() and toBack() as well, but no luck.
Now that I think about it (I'm sure this is related), I've noticed issues with text/labels interfering with the "click-ability" of an object that it is overlapping. Since the text generally occupies little pixels in terms of the width of the actual text, it just seems to only sometimes interfere with onMouseClicked events - if you click on the right spot that is. If you disable the node, do the pixels the text/label occupy become "dead"? as in that space cannot be used to initiate the onMouseClicked event of an object behind the text? Make sense?
Any ideas?

I've put up a picture for your reference: [http://imagebin.ca/view/Lj9C7q.html]
How it works is that each node can be clicked on, thus increasing its opacity to 1.0. Once "selected" there is a mouse enter/exit event for that particular node which allows the X icon to fade in/out to delete the node.
What's happening is that if you click on the X of the selected node, the node directly above (1432-1481) is being selected, although the deletion of the original node works fine.
Also the onMouseEnter event is firing for the "1432-1481" node if you hover over the X. As you can tell in the screenshot, the opacity is increased if you hover over an unselected node. You can see that the "1432-1481" is slightly brighter than the other nodes above it. Obviously the cursor is missing from the screenshot but it should make sense.

Cluster Node paused

Hi there
My Setup:
2 Cluster Nodes (HP DL380 G7 & HP DL380 Gen8)
HP P2000 G3 FC MSA (MPIO)
The Gen8 Cluster Node pauses after a few minutes, but stays online if the G7 is paused (no drain) My troubleshooting has led me to believe that there is a problem with the Cluster Shared Volume:
00001508.000010b4::2015/02/19-14:51:14.189 INFO [RES] Network Name: Agent: Sending request Netname/RecheckConfig to NN:cf2dec1d-ee88-4fb6-a86d-0c2d1aa888b4:Netbios
00000d1c.0000299c::2015/02/19-14:51:14.615 INFO [API] s_ApiGetQuorumResource final status 0.
00000d1c.0000299c::2015/02/19-14:51:14.616 INFO [RCM [RES] Virtual Machine VirtualMachine1 embedded failure notification, code=0 _isEmbeddedFailure=false _embeddedFailureAction=2
00001508.000010b4::2015/02/19-14:51:15.010 INFO [RES] Network Name <Cluster Name>: Getting Read only private properties
00000d1c.00002294::2015/02/19-14:51:15.096 INFO [API] s_ApiGetQuorumResource final status 0.
00000d1c.00002294::2015/02/19-14:51:15.121 INFO [API] s_ApiGetQuorumResource final status 0.
000014a8.000024f4::2015/02/19-14:51:15.269 INFO [RES] Physical Disk <Quorum>: VolumeIsNtfs: Volume
\\?\GLOBALROOT\Device\Harddisk1\ClusterPartition2\ has FS type NTFS
00000d1c.00002294::2015/02/19-14:51:15.343 WARN [RCM] ResourceTypeChaseTheOwnerLoop::DoCall: ResType MSMQ's DLL is not present on this node. Attempting to find a good node...
00000d1c.00002294::2015/02/19-14:51:15.352 WARN [RCM] ResourceTypeChaseTheOwnerLoop::DoCall: ResType MSMQTriggers's DLL is not present on this node. Attempting to find a good node...
000014a8.000024f4::2015/02/19-14:51:15.386 INFO [RES] Physical Disk: HardDiskpQueryDiskFromStm: ClusterStmFindDisk returned device='\\?\mpio#disk&ven_hp&prod_p2000_g3_fc&rev_t250#1&7f6ac24&0&36304346463030314145374646423434393243353331303030#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
000014a8.000024f4::2015/02/19-14:51:15.386 ERR   [RES] Physical Disk: HardDiskpGetDiskInfo: GetVolumeInformation failed for
\\?\GLOBALROOT\Device\Harddisk3\ClusterPartition2\, status 3
000014a8.000024f4::2015/02/19-14:51:15.386 ERR   [RES] Physical Disk: HardDiskpGetDiskInfo: failed to get partition size for
\\?\GLOBALROOT\Device\Harddisk3\ClusterPartition2\, status 3
00000d1c.00001420::2015/02/19-14:51:15.847 WARN [RCM] ResourceTypeChaseTheOwnerLoop::DoCall: ResType MSMQ's DLL is not present on this node. Attempting to find a good node...
00000d1c.00001420::2015/02/19-14:51:15.855 WARN [RCM] ResourceTypeChaseTheOwnerLoop::DoCall: ResType MSMQTriggers's DLL is not present on this node. Attempting to find a good node...
000014a8.000024f4::2015/02/19-14:51:15.887 INFO [RES] Physical Disk: HardDiskpQueryDiskFromStm: ClusterStmFindDisk returned device='\\?\mpio#disk&ven_hp&prod_p2000_g3_fc&rev_t250#1&7f6ac24&0&36304346463030314145374646423434393243353331303030#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
000014a8.000024f4::2015/02/19-14:51:15.888 ERR   [RES] Physical Disk: HardDiskpGetDiskInfo: GetVolumeInformation failed for
\\?\GLOBALROOT\Device\Harddisk3\ClusterPartition2\, status 3
000014a8.000024f4::2015/02/19-14:51:15.888 ERR   [RES] Physical Disk: HardDiskpGetDiskInfo: failed to get partition size for
\\?\GLOBALROOT\Device\Harddisk3\ClusterPartition2\, status 3
00000d1c.00001420::2015/02/19-14:51:15.928 WARN [RCM] ResourceTypeChaseTheOwnerLoop::DoCall: ResType MSMQ's DLL is not present on this node. Attempting to find a good node...
00000d1c.00001420::2015/02/19-14:51:15.939 WARN [RCM] ResourceTypeChaseTheOwnerLoop::DoCall: ResType MSMQTriggers's DLL is not present on this node. Attempting to find a good node...
000014a8.000024f4::2015/02/19-14:51:15.968 INFO [RES] Physical Disk: HardDiskpQueryDiskFromStm: ClusterStmFindDisk returned device='\\?\mpio#disk&ven_hp&prod_p2000_g3_fc&rev_t250#1&7f6ac24&0&36304346463030314145374646423434393243353331303030#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
000014a8.000024f4::2015/02/19-14:51:15.969 ERR   [RES] Physical Disk: HardDiskpGetDiskInfo: GetVolumeInformation failed for
\\?\GLOBALROOT\Device\Harddisk3\ClusterPartition2\, status 3
000014a8.000024f4::2015/02/19-14:51:15.969 ERR   [RES] Physical Disk: HardDiskpGetDiskInfo: failed to get partition size for
\\?\GLOBALROOT\Device\Harddisk3\ClusterPartition2\, status 3
00000d1c.00001420::2015/02/19-14:51:16.005 WARN [RCM] ResourceTypeChaseTheOwnerLoop::DoCall: ResType MSMQ's DLL is not present on this node. Attempting to find a good node...
00000d1c.00001420::2015/02/19-14:51:16.015 WARN [RCM] ResourceTypeChaseTheOwnerLoop::DoCall: ResType MSMQTriggers's DLL is not present on this node. Attempting to find a good node...
000014a8.000024f4::2015/02/19-14:51:16.059 INFO [RES] Physical Disk: HardDiskpQueryDiskFromStm: ClusterStmFindDisk returned device='\\?\mpio#disk&ven_hp&prod_p2000_g3_fc&rev_t250#1&7f6ac24&0&36304346463030314145374646423434393243353331303030#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}'
000014a8.000024f4::2015/02/19-14:51:16.059 ERR   [RES] Physical Disk: HardDiskpGetDiskInfo: GetVolumeInformation failed for
\\?\GLOBALROOT\Device\Harddisk3\ClusterPartition2\, status 3
000014a8.000024f4::2015/02/19-14:51:16.059 ERR   [RES] Physical Disk: HardDiskpGetDiskInfo: failed to get partition size for
\\?\GLOBALROOT\Device\Harddisk3\ClusterPartition2\, status 3
00000d1c.00002568::2015/02/19-14:51:17.110 INFO [GEM] Node 1: Deleting [2:395 , 2:396] (both included) as it has been ack'd by every node
00000d1c.0000299c::2015/02/19-14:51:17.444 INFO [RCM [RES] Virtual Machine VirtualMachine2 embedded failure notification, code=0 _isEmbeddedFailure=false _embeddedFailureAction=2
00000d1c.0000299c::2015/02/19-14:51:18.103 INFO [RCM] rcm::DrainMgr::PauseNodeNoDrain: [DrainMgr] PauseNodeNoDrain
00000d1c.0000299c::2015/02/19-14:51:18.103 INFO [GUM] Node 1: Processing RequestLock 1:164
00000d1c.00002568::2015/02/19-14:51:18.104 INFO [GUM] Node 1: Processing GrantLock to 1 (sent by 2 gumid: 1470)
00000d1c.0000299c::2015/02/19-14:51:18.104 INFO [GUM] Node 1: executing request locally, gumId:1471, my action: /nsm/stateChange, # of updates: 1
00000d1c.00001420::2015/02/19-14:51:18.104 INFO [DM] Starting replica transaction, paxos: 99:99:50133, smartPtr: HDL( c9b16cf1e0 ), internalPtr: HDL( c9b21
This issue has been bugging me for some time now. The Cluster is fully functional and works great until the node gets paused again. I've read somewhere that the MSMQ errors can be ignored, but can't find anything about the
HardDiskpGetDiskInfo: GetVolumeInformation failed messages. No errors in the san or the Server Event logs. Driver and Firmware are up to date. Any help would be greatly appreciated.
Best regards

Thank you for your replies.
First some information I left out in my original post. We're using Windows Server 2012 R2 Datacenter and are currently only hosting virtual machines on the cluster.
I did some testing over the weekend, including a firmware update on the san and cluster validation.
The problem doesn't seem to be related to backup. We use Microsoft DPM to make a full express backup once every day, the getvolumeinformation Failed error gets logged periodically every half an hour.
Excerpts from the validation report:
Validate Disk Failover
Description: Validate that a disk can fail over successfully with
data intact.
Start: 21.02.2015 18:02:17.
Node Node2 holds the SCSI PR on Test Disk 3
and brought the disk online, but failed in its attempt to write file data to
partition table entry 1. The disk structure is corrupted and
unreadable.
Stop: 21.02.2015 18:02:37.
Node Node1 holds the SCSI PR on Test Disk 3
and brought the disk online, but failed in its attempt to write file data to
partition table entry 1. The disk structure is corrupted and unreadable.
Validate File System
Description: Validate that the file system on disks in shared
storage is supported by failover clusters and Cluster Shared Volumes (CSVs).
Failover cluster physical disk resources support NTFS, ReFS, FAT32, FAT, and
RAW. Only volumes formatted as NTFS or ReFS are accessible in disks added as
CSVs.
The test was canceled.
Validate Simultaneous Failover
Description: Validate that disks can fail over simultaneously with
data intact.
The test was canceled.
Validate Storage Spaces Persistent Reservation
Description: Validate that storage supports the SCSI-3 Persistent
Reservation commands needed by Storage Spaces to support clustering.
Start: 21.02.2015 18:01:00.
Verifying there are no Persistent Reservations, or Registration
keys, on Test Disk 3 from node Node1. Issuing Persistent Reservation REGISTER AND IGNORE EXISTING KEY
using RESERVATION KEY 0x0 SERVICE ACTION RESERVATION KEY 0x30000000a for Test
Disk 3 from node Node1.
Issuing Persistent Reservation RESERVE on Test Disk 3 from node
Node1 using key 0x30000000a.
Issuing Persistent Reservation REGISTER AND IGNORE EXISTING KEY
using RESERVATION KEY 0x0 SERVICE ACTION RESERVATION KEY 0x3000100aa for Test
Disk 3 from node Node2.
Issuing Persistent Reservation REGISTER using RESERVATION KEY
0x30000000a SERVICE ACTION RESERVATION KEY 0x30000000b for Test Disk 3 from node
Node1 to change the registered key while holding the
reservation for the disk.
Verifying there are no Persistent Reservations, or Registration
keys, on Test Disk 2 from node Node1.
Issuing Persistent Reservation REGISTER AND IGNORE EXISTING KEY
using RESERVATION KEY 0x0 SERVICE ACTION RESERVATION KEY 0x20000000a for Test
Disk 2 from node Node1.
Issuing Persistent Reservation RESERVE on Test Disk 2 from node
Node1 using key 0x20000000a.
Issuing Persistent Reservation REGISTER AND IGNORE EXISTING KEY
using RESERVATION KEY 0x0 SERVICE ACTION RESERVATION KEY 0x2000100aa for Test
Disk 2 from node Node2.
Issuing Persistent Reservation REGISTER using RESERVATION KEY
0x20000000a SERVICE ACTION RESERVATION KEY 0x20000000b for Test Disk 2 from node
Node1 to change the registered key while holding the
reservation for the disk.
Verifying there are no Persistent Reservations, or Registration
keys, on Test Disk 0 from node Node1.
Issuing Persistent Reservation REGISTER AND IGNORE EXISTING KEY
using RESERVATION KEY 0x0 SERVICE ACTION RESERVATION KEY 0xa for Test Disk 0
from node Node1.
Issuing Persistent Reservation RESERVE on Test Disk 0 from node
Node1 using key 0xa.
Issuing Persistent Reservation REGISTER AND IGNORE EXISTING KEY
using RESERVATION KEY 0x0 SERVICE ACTION RESERVATION KEY 0x100aa for Test Disk 0
from node Node2.
Issuing Persistent Reservation REGISTER using RESERVATION KEY
0xa SERVICE ACTION RESERVATION KEY 0xb for Test Disk 0 from node
Node1 to change the registered key while holding the
reservation for the disk.
Verifying there are no Persistent Reservations, or Registration
keys, on Test Disk 1 from node Node1.
Issuing Persistent Reservation REGISTER AND IGNORE EXISTING KEY
using RESERVATION KEY 0x0 SERVICE ACTION RESERVATION KEY 0x10000000a for Test
Disk 1 from node Node1.
Issuing Persistent Reservation RESERVE on Test Disk 1 from node
Node1 using key 0x10000000a.
Issuing Persistent Reservation REGISTER AND IGNORE EXISTING KEY
using RESERVATION KEY 0x0 SERVICE ACTION RESERVATION KEY 0x1000100aa for Test
Disk 1 from node Node2.
Issuing Persistent Reservation REGISTER using RESERVATION KEY
0x10000000a SERVICE ACTION RESERVATION KEY 0x10000000b for Test Disk 1 from node
Node1 to change the registered key while holding the
reservation for the disk.
Failure. Persistent Reservation not present on Test Disk 3 from
node Node1 after successful call to update reservation holder's
registration key 0x30000000b.
Failure. Persistent Reservation not present on Test Disk 1 from
node Node1 after successful call to update reservation holder's
registration key 0x10000000b.
Failure. Persistent Reservation not present on Test Disk 0 from
node Node1 after successful call to update reservation holder's
registration key 0xb.
Failure. Persistent Reservation not present on Test Disk 2 from
node Node1 after successful call to update reservation holder's
registration key 0x20000000b.
Test Disk 0 does not support SCSI-3 Persistent Reservations
commands needed by clustered storage pools that use the Storage Spaces
subsystem. Some storage devices require specific firmware versions or settings
to function properly with failover clusters. Contact your storage administrator
or storage vendor for help with configuring the storage to function properly
with failover clusters that use Storage Spaces.
Test Disk 1 does not support SCSI-3 Persistent Reservations
commands needed by clustered storage pools that use the Storage Spaces
subsystem. Some storage devices require specific firmware versions or settings
to function properly with failover clusters. Contact your storage administrator
or storage vendor for help with configuring the storage to function properly
with failover clusters that use Storage Spaces.
Test Disk 2 does not support SCSI-3 Persistent Reservations
commands needed by clustered storage pools that use the Storage Spaces
subsystem. Some storage devices require specific firmware versions or settings
to function properly with failover clusters. Contact your storage administrator
or storage vendor for help with configuring the storage to function properly
with failover clusters that use Storage Spaces.
Test Disk 3 does not support SCSI-3 Persistent Reservations
commands needed by clustered storage pools that use the Storage Spaces
subsystem. Some storage devices require specific firmware versions or settings
to function properly with failover clusters. Contact your storage administrator
or storage vendor for help with configuring the storage to function properly
with failover clusters that use Storage Spaces.
Stop: 21.02.2015 18:01:02
Thank you for your help.
David

When i download any file it start in a second but when i pause the downloading file & after some time when i open it amessage flash 'download error' source file could not be read please try again later or contact the server administrator.

when i download any file it works frequently and downloading start in a second but when i pause the downloading file & after some time when i open it,The downloading not start proper and after some time a message flash 'download error' source file could not be read please try again later or contact the server administrator.

I downloaded the Microsoft Autoruns package and ran it. There are no programs in the LSA Providers tab, and Apple's Bonjour is the only program in the Winsock Providers tab. I also did the "netsh winsock reset" and rebooted. It didn't fix the problem. Any more ideas?

I have a iPhone 4S and when watching videos on the internet sound cuts out as the video is playing. The rest of the video plays with no sound. Sometimes when I pause It and play again sound comes back but not all the time. can anyone help?

I have a iPhone 4S and when watching videos on the internet sound cuts out as the video is playing. The rest of the video plays with no sound. Sometimes when I pause It and play again sound comes back but not all the time. can anyone help?

The "restore disk" is built into the Mac. See About Recovery.
Need more specifics about what error messages you got while installing Adobe Flash.
However, you can almost avoid Flash altogether by setting YouTube to play the HTML5 version instead.
Click the Try something new! link at the bottom of the YouTube page.
I don't know about the sound issue. Might be hardware as you think. Try other headphones to check.

When I stream videos from my laptop onto my Apple TV via my iPad 2 using the Air Video app/server the video plays great however when I pause the video the Apple TV reverts back to the home screen within a few seconds and then when I want to restart watchi

When I stream videos from my laptop onto my Apple TV via my iPad 2 using the Air Video app/server the video plays great however when I pause the video the Apple TV reverts back to the home screen within a few seconds and then when I want to restart watching the video I have to re-buffer the video. Is there any way I can stop the Apple TV from reverting back to the home screen when I pause the video I’m watching?

Welcome to the Apple Community.
Contact the developer of the Air Video app.

HT5148 i am using final cut pro x. i have imported some images and video in my timeline. when i play back my video it looks fuzzy. but, when i pause it, it looks clear. how do i get my video to play clear.

i am using final cut pro x. i have imported some images and video in my timeline. when i play back my video it looks fuzzy. but, when i pause it, it looks clear again. how do i get my video to play clear and not fuzzy?

Same reply.

Imported analog video successfully and it is normal in the "Event" pane but when I move a clip into the "Project" pane, it enlarges it slightly and distorts it. How can I keep that from happening?

Imported analog video successfully and it is normal in the "Event" pane but when I move a clip into the "Project" pane, it enlarges it slightly and distorts it. How can I keep that from happening?

Hi
Turn off analyze/image stabilization.
Yours Bengt W

Pixelated images when in preview mode on iMovie, but when I pause it the images become clear. How do I fix this?

I just bought the latest version of iMovie and I am on 10.9.4. I transferred my slideshow from the old iMovie to the new one and almost all the pictures become pixelated when in preview mode. Yet when I pause it, the picture becomes clear. What do I do? It's driving me insane!

After more attemps at cropping Im noticing that the saved version is unzoomed, so if I move the zoom bar just a tad the image becomes instantly sharp. But sadly that doesnt help me because iphoto will only let me save it and post it online as the unsharp pixulated version. Can anyone please help me!

When I "pause" shows on apple tv , the menu resets

Starting last week, whenever I pause a program on my apple TV for more than a minute, it kicks back to the basic apple TV screen.
It's as if I hit tha "back" button (but I didn't).
This happens with netflix, hulu plus and watching shows from my computer on the Apple TV.
I don't have any issues with buffering or streaming content, only when I pause a show.
I didn't see anything in the settings that I could change.
I used to be able to pause shows for 5-10 minutes with no issues and come back to unpause and watch the rest.
Now I have to go back into the netflix or hulu plus app and navigate back to my show, which is a pain.
Any suggestions?

mirror mean that it display the same resolution as the ios device
if it does not fill your whole screen use your tv remote to pull the images sides or to cut top and buttom
as ios devices are not widescreen like the tv

When I pause the sound still continues

When I pause the sound still continues. When will I test the movie in the timeline and use the timeline buttons not break the sound along with the image , it continues until it stops , the problem is that I have very long sounds and he plays to the end.

I'm guessing that the sound is embedded in the timeline. If this is the case, then select the keyframe where the sound starts and then, in the Properties window, set the Sync property for the selected sound to "Stream".

Is there any event that triggers when you switch between components?

is there any event that triggers when you switch between components?
like for example... when i switch between components, i need a function to fire everytime i switch...
ive tried show, hide, and initialize... and none of them work...
any ideas or help is greately appretiated!!

Depends on what you are trying to do,
you have mouseover and mouseout and mouseclick events which you can use on the component and write code to deal with what you want to happen when you change focus. You have keypress event which would allow you to monitor tabbing between components, remember that in most events the currentTarget and target values will give you the information you need to handle component interaction.
so
[Bindable] private var CurrentObject: Object; <------- use this as a pointer to what ever object you are currently focused on or just to indicate things have changed
addeventListener(MouseEvent.CLICK,myCompponentSwap);
protected function myComponentSwap(e:event): void
    if (CurrentObject !=e.currentTarget && CurrentObject != null)
         do what you want becuase a component switch just happened
    CurrentObject = e.currentTarget;
Hope this gets you started.
David

The new event are created when i import photo in the top. Before they where put in the end. All my event are classified. Where i can set the event at the end ? Thank's.

The new event are created when i import photo in the top.
Before they where put in the end.
All my event (around 600) are classified on the top the old and a the end the new.
Where i can set the event at the end ?
Thank's.

View menu ==> sort events
LN

Bluetooth Disconnected when playback paused and never resume again

I am using Nokia BH-111 with my Dell Inspiron N4110. I am facing issues from last week that when I paused playback of audio/video, the Audio never resumes. I won't hear any voice at all. I need to turn off the Bluetooth adapter and have to restart it again.
But it was working fine before that and Nokia BH-111 is also working fine with my other devices. Could you provide some assistance.

Hi,
Did you do any changes for your computer? Since your had mentioned that it worked fine before. Please try system restore to roll back to a time when everything worked fine to see if the issue could be resolved.
Karen Hu
TechNet Community Support

Event ID 1135 When Node Paused

Similar Messages

Maybe you are looking for