Everything is working (wifi out), but arch pc is not pingable
Hi there!
Please excuse any formal errors, this is my first post here. I tried to find some
helpful post in the forum but didn't get anything helping me with this situation.
Setup: Router(Fritzbox), Windows 7, Arch,....
On my Arch I have a RealTek 8192CE wifi module, which I got working very well
by disabling ips and fwlps)
Workin right now on the Arch and wifi is just working fine, but there is no chance
to get pinged by other machines.
My Settings:
(wicd is doing the wifi connection)
# /etc/rc.conf - Main Configuration for Arch Linux
# See 'man 5 rc.conf' for more details
# LOCALIZATION
HARDWARECLOCK="localtime"
TIMEZONE="Europe/Berlin"
KEYMAP="de-latin1-nodeadkeys"
CONSOLEFONT=
CONSOLEMAP=
LOCALE="de_DE.UTF-8"
DAEMON_LOCALE="yes"
USECOLOR="yes"
# HARDWARE
MODULES=()
USEDMRAID="no"
USEBTRFS="no"
USELVM="no"
# NETWORKING
HOSTNAME=idearch
INTERFACE=
address=
netmask=
broadcast=
gateway=
NETWORK_PERSIST="no"
# DAEMONS
DAEMONS=(syslog-ng dbus wicd mpd mpdscribble sshd crond)
ifconfig
wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 metric 1
inet 192.168.178.34 netmask 255.255.255.0 broadcast 192.168.178.255
inet6 fe80::2210:7aff:fe39:466d prefixlen 64 scopeid 0x20<link>
ether 20:10:7a:39:46:6d txqueuelen 1000 (Ethernet)
RX packets 9846 bytes 5316090 (5.0 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 9987 bytes 1929228 (1.8 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 192.168.178.1 0.0.0.0 UG 303 0 0 wlan0
192.168.178.0 0.0.0.0 255.255.255.0 U 303 0 0 wlan0
wicd.log
2012/07/10 22:48:18 :: enctype is wpa-psk
2012/07/10 22:48:18 :: Attempting to authenticate...
2012/07/10 22:48:18 :: ['wpa_supplicant', '-B', '-i', 'wlan0', '-c', '/var/lib/wicd/configurations/1caff7de7331', '-Dwext']
2012/07/10 22:48:18 :: ['iwconfig', 'wlan0', 'essid', '--', 'D-Link oben']
2012/07/10 22:48:18 :: iwconfig wlan0 channel 1
2012/07/10 22:48:18 :: iwconfig wlan0 ap 1C:AF:F7:DE:73:31
2012/07/10 22:48:18 :: WPA_CLI RESULT IS DISCONNECTED
2012/07/10 22:48:19 :: iwconfig wlan0
2012/07/10 22:48:19 :: WPA_CLI RESULT IS COMPLETED
2012/07/10 22:48:19 :: Running DHCP with hostname idearch
2012/07/10 22:48:19 :: /usr/sbin/dhcpcd -h idearch --noipv4ll wlan0
2012/07/10 22:48:19 :: dhcpcd[4600]: version 5.5.6 starting
2012/07/10 22:48:19 ::
2012/07/10 22:48:19 :: dhcpcd[4600]: wlan0: sending IPv6 Router Solicitation
2012/07/10 22:48:19 ::
2012/07/10 22:48:19 :: dhcpcd[4600]: wlan0: sendmsg: Cannot assign requested address
2012/07/10 22:48:19 ::
2012/07/10 22:48:19 :: dhcpcd[4600]: wlan0: broadcasting for a lease
2012/07/10 22:48:19 ::
2012/07/10 22:48:21 :: iwconfig wlan0
2012/07/10 22:48:23 :: dhcpcd[4600]: wlan0: sending IPv6 Router Solicitation
2012/07/10 22:48:23 ::
2012/07/10 22:48:23 :: iwconfig wlan0
2012/07/10 22:48:25 :: dhcpcd[4600]: wlan0: offered 192.168.178.34 from 192.168.178.1
2012/07/10 22:48:25 ::
2012/07/10 22:48:25 :: dhcpcd[4600]: wlan0: acknowledged 192.168.178.34 from 192.168.178.1
2012/07/10 22:48:25 ::
2012/07/10 22:48:25 :: dhcpcd[4600]: wlan0: checking for 192.168.178.34
2012/07/10 22:48:25 ::
2012/07/10 22:48:26 :: iwconfig wlan0
2012/07/10 22:48:27 :: dhcpcd[4600]: wlan0: sending IPv6 Router Solicitation
2012/07/10 22:48:27 ::
2012/07/10 22:48:28 :: iwconfig wlan0
2012/07/10 22:48:30 :: iwconfig wlan0
2012/07/10 22:48:31 :: dhcpcd[4600]: wlan0: leased 192.168.178.34 for 864000 seconds
2012/07/10 22:48:31 ::
2012/07/10 22:48:31 :: dhcpcd[4600]: forked to background, child pid 4659
2012/07/10 22:48:31 ::
2012/07/10 22:48:31 ::
2012/07/10 22:48:31 :: DHCP connection successful
2012/07/10 22:48:31 :: not verifying
2012/07/10 22:48:31 :: Connecting thread exiting.
2012/07/10 22:48:31 :: ifconfig wlan0
2012/07/10 22:48:31 :: IP Address is: 192.168.178.34
2012/07/10 22:48:32 :: Sending connection attempt result success
2012/07/10 22:48:32 :: ifconfig eth0
2012/07/10 22:48:32 :: Reading wired profile wired-default
2012/07/10 22:48:32 :: found ip in configuration None
2012/07/10 22:48:32 :: found broadcast in configuration None
2012/07/10 22:48:32 :: found netmask in configuration None
2012/07/10 22:48:32 :: found gateway in configuration None
2012/07/10 22:48:32 :: found search_domain in configuration None
2012/07/10 22:48:32 :: found dns_domain in configuration None
2012/07/10 22:48:32 :: found dns1 in configuration None
2012/07/10 22:48:32 :: found dns2 in configuration None
2012/07/10 22:48:32 :: found dns3 in configuration None
2012/07/10 22:48:32 :: found beforescript in configuration None
2012/07/10 22:48:32 :: found afterscript in configuration None
2012/07/10 22:48:32 :: found predisconnectscript in configuration None
2012/07/10 22:48:32 :: found postdisconnectscript in configuration None
2012/07/10 22:48:32 :: found encryption_enabled in configuration None
2012/07/10 22:48:32 :: found default in configuration True
2012/07/10 22:48:32 :: found dhcphostname in configuration idearch
What I know:
Until yesterday everything worked (could be caused by the install of the samb
server, but no hints in what way it could be the culprit)
tcpdump shows no incoming or failed transfers for ping or ssh attempts from other
units in the local network.
The error from outside is a "connection time out"
The router does not receive the hostname (I suspect this being essential since the
showed up before)
What I'd like to know:
Where can I search further, what log files should I go through?
Thanks a lot!
bene
Edit:
While browsing there are interesting entries in tcpdump:
ARP, Request who-has 192.168.178.34 tell fritz.box, length 46
Last edited by bene (2012-07-10 21:15:41)
Figured it out by myself, there were invalid ARP entries, due to an old firmware on the second access point.
Similar Messages
-
I just downloaded Mountain Lion and everything is working great. But i keep getting an error in the app store and i can't download 'Pages' or any other apps. I keep getting an "error" and it says credit card processing is temporarily unavailable......help
Try deleting the cache associated with the App Store.
Quit the App Store if it's open.
Open the Finder. From the Finder menu bar click Go > Go to Folder
Type this exactly as you see it here:
~/Library/Caches/com.apple.appstore/Cache.db
Click Go
Move the Cache.db file to the Trash.
Launch the App Store. See if that made a difference... -
I am able to log onto my work wifi network but my Iphone
I am able to log onto my work wifi network but my Iphone keeps disconnecting - requiring me to re-enter my username and password to rejoin the network continuoulsy. Is there a solution to this?
Rds
ShawnThanks, checked all of that at work. It seems from other users I am not alone. Hopefully the updated IOS will fix this. In the meantime, a considerable inconvenience.
-
i buy my ipod touch like 6 months ago it was working very well but yesterday it is not connecting to the internet when i am connect to my internet it said unable to connect can you please tell me plz help me
Do other devices successfully connect to the router?
Does the iPod successfully connect to other networks/routers?
Does the iPod show wifi bands in the upper left?
Try:
- Resetting the iPod:
Reset iPod touch: Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
- Powering off and then back on the router
- Resetting networksettings: Settings>General>Reset>Reet Network Setting
- The troubleshooting here
iPhone and iPod touch: Troubleshooting Wi-Fi networks and connections -
I had my iphone 4s synced to itunes on my work laptop. The IT group at work stripped out that installation and will not allow me to reinstall. My iphone insists it has to sync to my work laptop itunes. How do I change iphone settings to look at an itunes installation on my personal laptop?
dcotejr wrote:
I had my iphone 4s synced to itunes on my work laptop. ... How do I change iphone settings to look at an itunes installation on my personal laptop?
You cannot.
By Design the iPhone can Only Sync to One iTunes Library at a time. -
Hi, the FaceTime just did not work between my mom and I. It used to work weeks ago, but now it does not work after showing"connecting". I feel frustrated and try all the method I can think of. Still do not work. Hope u can help me. Thanks!
Was it just this one time? Could be that you, or your mom, were experiencing network problems. Try again at a later time.
-
Hi, I'm trying to extract the nano sim tray on my new Ipad air. I know how it should come out but the tool does not seem to release the tray. Any ideas?
Thanks. It needed more pressure than I expected!
Didn't want to break it when it's less then 24 hours old!
BB -
The Apple ID that is coming up on my App Store is my wife's but I am logged in under my own, I have logged out and back in but it is still logging in on hers can anyone help???
I am afraid all apps are tied to the Apple ID they are purchased with and are not transferable.
Your son have to buy those apps with his own Apple ID and start from scratch. -
Connected to Airport WiFi Net but Airport Utility does not "see" the AE(n)
Have both the Airport Extreme (g) and (n). Have no problems with the AE(g) which I am using now, but the AE(n) somehow does not appear in the "Airport Utility".
I see the new AE(n) in the Airport Finder selection tool and I connect to the AE(n) network WiFi. The connection is successful and I get all of the vertical black semi-circles showing connection. Then I open Airport Utility and attempt to scan to see the AE(n) and it does not appear.
I've tried to hard reset the AE(n) and configure using Ethernet. The AE(n), appears in Airport Utility when attached by Ethernet. Once configured. I disconnet the Ethernet cable and connect to the new WiFi network but the Amber light flashes, the AE(n) does not connect successfully to the DSL modem and my iMac (Core Duo) Airport Utility program fails to "see" the new base station. I am going nuts. Pls help.
I did read through other problems and the troubleshooting section and did not come accross this same problem.Spent 75 minutes on the phone with Apple support. At the end of the day learned a few things.
1) Hold down control key to get additonal wireless config options including one which allows 802.11b/g only
2) Using "Other" as a network option in the Internet Connect application solves the problem that only "WPA" password is allowed while I have configured my AE to WEP. You need to type in the AE network name but you are allowed to choose the correct password schema
3) Using "Network Utility" and pinging 10.0.1.1 found out that I had 90% packet loss and that my new AE(n) is most likely defective and in need of replacement...
After all that am back to using my AE(g). -
I have tried everything I know to try, but I cannot get my Ipad to connect to my HP laserjet P1102W printer. Any suggestions.
http://h30434.www3.hp.com/t5/Printer-Networking-and-Wireless/P1102w-and-AirPrint /td-p/734491
-
All of a sudden the internet on our Macbook Pro does not work. We connect through an Airport Extreme and other mac works fine. It shows that wifi is fully connected but when i go to diagnostics, i see the internet and server are failing. I tried connecting an ethernet cable and it doesn't work that way either. Have restarted and reset modem and router, nothing is working… help!
Hi ehamzic1,
Welcome to the Apple Support Communities!
I understand how frustrating it can be when your computer cannot connect to the internet. In your situation, you will need to isolate to find what is causing the issues connecting. I would recommend reading over and working through the attached article. The article should help you troubleshoot and resolve this situation.
Solutions for connecting to the Internet, setting up a small network, and troubleshooting
http://support.apple.com/kb/HT1714
Have a great day,
Joe -
Wifi on but internet and youtube not working?
I currently have three bars of signal but my internet and youtube do not connect. I have tried re-booting but this does not seem to work. My tilt is also being slow.
- Reset the iPod. Nothing will be lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on the router.
- Reset networks settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- iOS: Recommended settings for Wi-Fi routers and access points
Did it successfully connect before?
Do other deviceses sucsessfully connect now? -
I can connect to the internet with no problems ,but I am unable to connect to the App Store. Error message reads--- Cannot connect to App Store.
Hey William,
It sounds as though you are having difficulty with your Mac being unable to connect to the Mac App Store. This article has some steps that may help you troubleshoot -
Can't connect to the iTunes Store - Apple Support
Note that the title is for the iTunes Store, the steps are still relevant.
Thanks for using Apple Support Communities.
Happy computing,
Brett L -
I have tried everything you told me to do I have only had this for three months it should not be having this much problems
Check your Settings > General > Restrictions > Camera?
-
Please help me!!
1) Apple ID: All about Apple ID security questions
If necessary...
2) See Here... ask to speak with the Account Security Team...
Apple ID: Contacting Apple for help with Apple ID account security
Or Email Here > Apple Support iTunes Store Contact
Maybe you are looking for
-
Hi guys, here is the scenario : we have a weblogic server running fine with a domain name "casa1" with 4 JVM's ( two on same machine and two on different machine ). And we created a newdomain "casa2" with 4 JVM's ( 2 on same machine and 2 on differen
-
Hi while i am monitoring in RWB under message monitoring Status System Error Error Category XI_J2EE_ADAPTER_FILE Error Code PROCESSING_ERROR It is in adapter engine In auditlog i am getting error like this Delivery of the message to the application
-
I cannot block some advertisements in the journal De Telegraaf, in The Netherlands. When I move the mouse to blokkeren (Dutch) this blokkeren disappers. How to solve it? edit
-
Combining max, average and group by
Hi! I have a simple table called Rates consisting of RateTime (datetime), Ask (decimal) and OrderSymbol (char) I'm trying to create a select statement that will give me one row for each unique value in OrderSymbol consisting of columns for "CurrentAs
-
Show popup in front of the applet
JDEVADF_11.1.1.2.0_GENERIC_091029.2229.5536 I use an applet in jspx when I open a popup with modal dialog appears the popUp in the background of applet :-(