Exchange Mail on Local LAN

I have a user that has an Exchange email account setup on his iPad (Wi-Fi only) and it works fine when he is away from the company. When he is connected to the companies Wi-Fi and is on the same local subnet as the Exchange server he can't connect to the server. He receives this error "Cannot Get Mail The connection to the server failed" Does anybody have any ideas, thanks?
Joe

My guess would be that your LAN's DNS server can't do internal routing. Many low-cost firewall/routers can't resolve a external domain name that point's back to itself. Assuming you have Outlook Web Access enabled, you can test this from a PC or Mac. In a browser, type in the domain name you used to configure the iPad.
For example, Outlook Web Access for my Exchange Server when I'm outside of the office is www.mycompany.com/owa. With my old router, if I typed that in while I was in the office, it would give me page not found. Typing in the local LAN IP address of the server rather than the domain name would work. (e.g.: 192.168.1.2/owa) Because www.mycompany.com pointed back to the LAN I was on, the routing failed. But of course, using the internal IP address wouldn't work when outside the office unless I also configured a VPN. (The VPN would connect the iPad to the "directly" to the internal LAN.)
I don't have any simple solution. What I did was replaced my router. There were other reasons I needed to replace the router, but one of the additional benefits was to get the internal routing.
So either get a different router or internal DNS server (or reconfigure the internal DNS server to route correctly, if possible. Or setup a VPN and configure the iPad to only use the internal IP address of the Exchange server.

Similar Messages

When I send e-mail messages with file by using a POP3 in Exchange 2010 I received delivered message with file. How I can disable this functions that file do not include to delivery message. I use Exchange 2010 only local users.

When I send e-mail messages with file by using a POP3 in Exchange 2010 I received delivered message with file. How I can disable this functions that file do not include to delivery message. I use Exchange 2010 only local users.

I think there is not native rule for this, but you could try a transport rule which removes all attachments over a very small file size like 1KB.
http://blogs.technet.com/b/exchange/archive/2009/05/11/3407435.aspx
CRM Advisor

ASA 5505 & VPN Client blocking access to local lan

I have setup a IPSec vpn client connection to a Cisco ASA 5505, when I connect to the unit it fully authenticates and issues me an ip address on the local lan however when I attempt to connect to any service on the local lan the following message is displayed in the log can you help:
Teardown UDP connection 192.168.110.200 53785 192.168.110.21 53 outside:192.168.110.200/53785(LOCAL\username) to inside 192.168.110/53
See the attached file for a sanitised version of the config.

This is a sanitised version of the crypto dump, I have changed the user and IP addresses
ASA5505MAN# debug crypto ikev1 7
ASA5505MAN# debug crypto ipsec 7
ASA5505MAN# Jul 24 15:49:03 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=fbc167de) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb72)
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb72)
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
Jul 24 15:49:03 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=515fbf7e) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:18 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=2fe7cf10) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb73)
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb73)
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
Jul 24 15:49:18 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=e450c971) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:28 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=e6c212e7) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb74)
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb74)
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
Jul 24 15:49:28 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=af5953c7) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
This is the isakmp dump
ASA5505MAN# show crypto isakmp
IKEv1 SAs:
   Active SA: 2
    Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 2
1   IKE Peer: x.x.x.x
    Type    : L2L             Role    : initiator
    Rekey   : no              State   : MM_ACTIVE
2   IKE Peer: x.x.x.x
    Type    : user            Role    : responder
    Rekey   : no              State   : AM_ACTIVE
There are no IKEv2 SAs
Global IKEv1 Statistics
Active Tunnels:              1
Previous Tunnels:           40
In Octets:              322076
In Packets:               2060
In Drop Packets:            84
In Notifys:               1072
In P2 Exchanges:            35
In P2 Exchange Invalids:     0
In P2 Exchange Rejects:      0
In P2 Sa Delete Requests:   24
Out Octets:             591896
Out Packets:              3481
Out Drop Packets:            0
Out Notifys:              2101
Out P2 Exchanges:          275
Out P2 Exchange Invalids:    0
Out P2 Exchange Rejects:     0
Out P2 Sa Delete Requests: 284
Initiator Tunnels:         231
Initiator Fails:           221
Responder Fails:            76
System Capacity Fails:       0
Auth Fails:                 54
Decrypt Fails:               0
Hash Valid Fails:            0
No Sa Fails:                30
Global IKEv2 Statistics
Active Tunnels:                          0
Previous Tunnels:                        0
In Octets:                               0
In Packets:                              0
In Drop Packets:                         0
In Drop Fragments:                       0
In Notifys:                              0
In P2 Exchange:                          0
In P2 Exchange Invalids:                 0
In P2 Exchange Rejects:                  0
In IPSEC Delete:                         0
In IKE Delete:                           0
Out Octets:                              0
Out Packets:                             0
Out Drop Packets:                        0
Out Drop Fragments:                      0
Out Notifys:                             0
Out P2 Exchange:                         0
Out P2 Exchange Invalids:                0
Out P2 Exchange Rejects:                 0
Out IPSEC Delete:                        0
Out IKE Delete:                          0
SAs Locally Initiated:                   0
SAs Locally Initiated Failed:            0
SAs Remotely Initiated:                  0
SAs Remotely Initiated Failed:           0
System Capacity Failures:                0
Authentication Failures:                 0
Decrypt Failures:                        0
Hash Failures:                           0
Invalid SPI:                             0
In Configs:                              0
Out Configs:                             0
In Configs Rejects:                      0
Out Configs Rejects:                     0
Previous Tunnels:                        0
Previous Tunnels Wraps:                  0
In DPD Messages:                         0
Out DPD Messages:                        0
Out NAT Keepalives:                      0
IKE Rekey Locally Initiated:             0
IKE Rekey Remotely Initiated:            0
CHILD Rekey Locally Initiated:           0
CHILD Rekey Remotely Initiated:          0
IKEV2 Call Admission Statistics
Max Active SAs:                   No Limit
Max In-Negotiation SAs:                 12
Cookie Challenge Threshold:          Never
Active SAs:                              0
In-Negotiation SAs:                      0
Incoming Requests:                       0
Incoming Requests Accepted:              0
Incoming Requests Rejected:              0
Outgoing Requests:                       0
Outgoing Requests Accepted:              0
Outgoing Requests Rejected:              0
Rejected Requests:                       0
Rejected Over Max SA limit:              0
Rejected Low Resources:                  0
Rejected Reboot In Progress:             0
Cookie Challenges:                       0
Cookie Challenges Passed:                0
Cookie Challenges Failed:                0
Global IKEv1 IPSec over TCP Statistics
Embryonic connections: 0
Active connections: 0
Previous connections: 0
Inbound packets: 0
Inbound dropped packets: 0
Outbound packets: 0
Outbound dropped packets: 0
RST packets: 0
Recevied ACK heart-beat packets: 0
Bad headers: 0
Bad trailers: 0
Timer failures: 0
Checksum errors: 0
Internal errors: 0
ASA5505MAN#
and this is the ipsec dump
ASA5505MAN# show crypto ipsec sa
interface: outside
    Crypto map tag: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: x.x.x.x
      local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.110.200/255.255.255.255/0/0)
      current_peer: x.x.x.x, username: username
      dynamic allocated peer ip: 192.168.110.200
      #pkts encaps: 778, #pkts encrypt: 778, #pkts digest: 778
      #pkts decaps: 1959, #pkts decrypt: 1959, #pkts verify: 1959
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 778, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #TFC rcvd: 0, #TFC sent: 0
      #Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: x.x.x.x/4500, remote crypto endpt.: x.x.x.x/54599
      path mtu 1500, ipsec overhead 82(52), media mtu 1500
      PMTU time remaining (sec): 0, DF policy: copy-df
      ICMP error validation: disabled, TFC packets: disabled
      current outbound spi: 532B60D0
      current inbound spi : 472C8AE7
    inbound esp sas:
      spi: 0x472C8AE7 (1194101479)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, IKEv1, }
         slot: 0, conn_id: 241664, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 26551
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0xFFFFFFFF 0xFFFFFFFF
    outbound esp sas:
      spi: 0x532B60D0 (1395351760)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, IKEv1, }
         slot: 0, conn_id: 241664, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 26551
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
    Crypto map tag: outside_map0, seq num: 1, local addr: x.x.x.x
      access-list outside_cryptomap_1 extended permit ip 192.168.110.0 255.255.255.0 192.168.0.0 255.255.0.0
      local ident (addr/mask/prot/port): (192.168.110.0/255.255.255.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.0.0/255.255.0.0/0/0)
      current_peer: x.x.x.x
      #pkts encaps: 39333117, #pkts encrypt: 39333117, #pkts digest: 39333117
      #pkts decaps: 24914965, #pkts decrypt: 24914965, #pkts verify: 24914965
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 39333117, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #TFC rcvd: 0, #TFC sent: 0
      #Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: x.x.x.x/0, remote crypto endpt.: x.x.x.x/0
      path mtu 1500, ipsec overhead 58(36), media mtu 1500
      PMTU time remaining (sec): 0, DF policy: copy-df
      ICMP error validation: disabled, TFC packets: disabled
      current outbound spi: F6943017
      current inbound spi : E6CDF924
    inbound esp sas:
      spi: 0xE6CDF924 (3872258340)
         transform: esp-3des esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, IKEv1, }
         slot: 0, conn_id: 163840, crypto-map: outside_map0
         sa timing: remaining key lifetime (kB/sec): (3651601/15931)
         IV size: 8 bytes
         replay detection support: Y
         Anti replay bitmap:
          0xFFFFFFFF 0xFFFFFFFF
    outbound esp sas:
      spi: 0xF6943017 (4136906775)
         transform: esp-3des esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, IKEv1, }
         slot: 0, conn_id: 163840, crypto-map: outside_map0
         sa timing: remaining key lifetime (kB/sec): (3561355/15931)
         IV size: 8 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
ASA5505MAN#

Does anybody know how to archive Exchange mails on Mac OS 10.4.11?

I set up an archive mailbox for a Mac user using 'New Mailbox' with location 'On My Mac'. I then set up a rule to move items older that 180 days to this mailbox. The mails appeared to archive successfully, however her Exchange mailbox hasn't decreased in size.
I also tried right-clicking her inbox and selecting 'Erase deleted messages' but this didn't work either. This version of Mac OS (10.4.11) doesn't seem to have any 'Archive Mailbox' option. What should I do?

I am not sure if you are using IMAP or a restricted version of MAPI.
Make sure the server has not replicated your local archive or is linked to it in any way - you would not want it to be trashed when you eventually delete the messages from the server - perhaps keep a zipped copy elsewhere for safety.
If you are unable to find a more global 'remove deleted messages from server' in Preferences you could consider:
1 - web access to delete archived emails
2 - accessing the server with POP (at least temporarily) as POP has well understood methods of deleting from server. However:
1 - Make sure POP does not delete more than required
2 - POP only communicates with the server's Inbox so will only download or delete Inbox messages.
A few details: http://www.msexchange.org/articles-tutorials/exchange-server-5-5/Connecting_POP_ And_IMAP_Clients_To_MS_Exchange_Server.html
In the longer term you could consider moving away from Exchange mail servers.

I have just setup an exchange mail account on my iphone and many of my settings have defaulted. Was this set by my business or by exchange?

I have just setup an exchange mail account on my iphone to acces smy business emails and many of my settings have defaulted. As an example, my passcode has defaulted to a minimum of 6 digits and my phone will erase all data after 10 failed attempts. These are now greyed out and I cannot change them.
Is this a default set by Apple/Microsoft?
Or was this a setting enforced by my company, whose mail exchange I am accessing?

ditto what KT said...the passcode requirement enables the encryption of the local storage of your device and auditing of that policy ..it protects your organization AND you from potential data loss and a mandatory reporting obligation..imagine how miserable it would be to see the name of your organization on the front page of your local newspaper with a story about data loss....every IT and risk management department's worst nightmare

How i implement sending a mail on local system also i want to see these mail as a receiver

Plz any one tell me ,
how can i implement sending a mail on local system also i
want to see these mail as a receiver.
any suggestion appreciated.
Regards
Prashant

Do some research on setting up an SMTP Mail Server. You need
one running somewhere on your box or on your network. Your box
would be 127.0.0.1 your network would be 10.x.x.xxx as given to you
by your network gurus. You may run into firewall issues also. Port
is typically 25. The SMTP server (the one that comes with IIS does)
often has settings to prohibit relays from external sources (CF
would be considered external). When I first got into this, I didn't
understand the concepts and tried to get my own IIS supplied SMTP
server up and running. It never worked (even efter permitting
relays), most likely due to the Corporate Network and security
properties and Firewalls etc. When I finally figured all this out ,
I was able to ask the Network Guru's, "Do we have an SMTP server I
can access?". Turns out they had something built into or bolted
onto MS Outlook Exchange Server, they gave me the IP, and presto,
everything worked as advertised.

Running lync on local lan ?

can lync server be run on local lan only ? for example a LAN in a remote location where there is no internet ? however the size of LAN is large with lots of client spread over a distant area.
Also is Lync server bundled in Exchange Server 2013 ?
sorry i am new to this.
regards
Faisal

Agree with Anthony. yes, you can run lync on LAN but users will be able to connect with lync on LAN only cand can't connect from their home/outside.
On premises, Lync Server is not Bundle with Exchange Server 2013. you will need to buy it's licenses and cals.
if you host it online at cloud like office 365, Lync is bundle with Exchange 2013
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"

Exchange mail after iOS 8 upgrade not working

exchange mail after iOS 8 upgrade not working.
I can not get email from my exchange account.
Any suggestion?

Just had this issue. I turned WIFI off and it connected fine. Then turned WIFI back on and working as always.
It had something to do with the WIFI conflicting with the exchange server.

Vpn site to site isa 570 to asa 5505 multiple local lan

Hello, i have configured a site to site vpn with a asa 5505
In the tunnel will pass the network 172.x.x.x/16 and 192.168.x.x/24 from local isa to a single lan 192.168.x.x/24 on remote asa
I have create a group network address and i put the the default_lan and the other lan in it
In the tunnell configuration i have use this group address with local lan parameter
When the tunnel was up in the routing table i view the remote lan on interface ipsec0 but also i view the local lan on interface ipsec0
Is this configuration n ot supported?
Thank best regards

Hello, thank for answer.
The problem is that tha second lan is a routing static lan.
The ip address of ISA is 172.16.10.254/16 and the default_lan is 172.16.0.0/16
The second lan is 202.1.1.0/24 and it is a staic lan on another gateway.
When the site-to-site ipsec go up in routing table i see three route on interface ipsec0:
The remote lan, the default-lan (that is also on default interface. Behaviour?) and a subnet lan 172.16.10.0/24.
If i ping from a lan pc an ip of subnet 172.16.10.0/24, i see that the arp is equal at mac-address of ISA and i have a problem on the lan. It's normal?
Best regards

Cisco ASA 5505 VPN help for local lan access.

Hi all,
I am very new to Cisco systems. Recently I was tasked to enable local lan access for one of my server. The problem is this. I have this server with 2 interfaces. One interface to my FTP server(192.168.2.3) and the other to the Cisco ASA(192.168.1.1). Whenever I connect the server to Cisco Anyconnect VPN, I am unable to access the FTP server anymore.
I googled and found out that the problem is because the metric level is 1 for Ciscoanyconnect network interface which causes all traffic to go through the Cisco VPN Interface. Another problem is I can't change the metric of the Cisco VPN Interface as whenever I reconnect to the VPN, the metric resets back to 1 again. I tried to follow some guides to configure split tunnel but my traffic is still going through the VPN connection.
Anyone can tell me what I am missing here? Sorry I am very new to Cisco systems. Spent about 5 days troubleshooting and I feel I am getting it soon. Anyone can guide me what else I am supposed to do?
What I did> Configuration>> Remote access VPN>> Network Client Access>> Group Policies>> Advanced>> Split Tunneling>> Uncheck Inherit and select "Exclude Network List below.>> Uncheck Network List and select Manage, Add 192.168.2.0/24 to permit.
Really appreciate if anyone can tell me what else I can do to ensure my server has access the my FTP Server after connecting to the VPN.
Thanks all!
Wen Qi

Hi,
Try adding the following configuration
policy-map global_policy
class inspection_default
inspect pptp
And then try again.
I'm not 100% would you need to perhaps allow GRE through the firewall even after that. (Protocol 47)
- Jouni

How can I set up my exchange mail on my iphone 5

how can I set up my exchange mail on my iphone 5?

http://support.apple.com/kb/HT2480
http://www.wikihow.com/Sync-Your-iPhone-with-Microsoft-Exchange

Exchange mail cannot work after upgrade to ios 8.3

just upgraded the ios to 8.3 yesterday, and the exchange mail could not work since then. no luck even after deleting and re-add the account.
anyone facing the same problem?
i will never trust Apple next time to upgrade the new OS at the first day.
iPhone 6

I have exactly the same problem. When I make a change in Settings Exchange checks itself off implying that it is working, but I keep getting "Cannot Reach Server" message whenever I try to get email.
I have become very leery of accepting the new IOS upgrades. There is always a problem.

Transparent Tunneling and Local Lan Access via VPN Client

Remote users using Cisco VPN 4.2 connect successfully to a Cisco Pix 515 (ver. 6.3). The client is configured to allow Transparent Tunneling and Local Lan access, but once connected to the Pix, these two options are disabled. What configuration changes are required on the Pix to enable these options? Any assistance will be greatly appreciated.
Mike Bowyer

Hi Mike,
"Transparent Tunneling" and "Local Lan Access" are two different things. "Transparent Tunneling" is dealing with establishing an IPSec Tunnel even if a NAT device is between your client and the VPN-Headend-Device. "Local LAN Access" is dealing with access to devices in the LAN your VPN-Client-Device is connected to.
What do you mean exactly with "disabled once the connection is made" ?
You can check the local LAN Access by having a look at the Route-Table of the VPN-Client:
Right Click the yellow VPN-lock Icon in System-Tray while the VPN-Connection is active and select "Statistics ...". Have a look at the second register page "route details".
Are any local LAN routes displayed when your are connected ?
And - always remember two important restrictions the Online Help of the VPN-Client is mentioning:
1: This feature works only on one NIC card, the same NIC card as the tunnel.
2: While connected, you cannot print or browse the local LAN by name; when disconnected, you can print and browse by name.
Carsten
PS: Removing Split Tunnel won't enable local LAN access as all traffic would be sent into the IPSec tunnel.

Exchange mail is marked "read" on iPhone and Exchange Mail

My boss asked me this morning if I had ever heard of this happening, and I have not. He syncs his exchange mail with his iPhone. He says that all of his mail appears on both devices marked as "read". He is using Windows 7. Has anyone had this problem? Can anyone point me in the right direction?

Hi there I'm having the same issue but only with 1 account,what was the fix?

Mail the local files as attachment and some body text

hello Exprests
I have a requirement where i have to mail the local files as attachment and some body text also...
I am using the following code, and the problem is that i am getting a blank TXT as an attachment.
Please help me solve this issue, if u change the spool request no., client & put ur mail id and execute it u will find that apart from the pdf we get an un wanted attachment also..
Please suggest me the solution..
WORK TABLE AREAS
TABLES: tsp01.
INTERNAL TABLES
DATA: lt_rec_tab LIKE STANDARD TABLE OF soos1 WITH HEADER LINE,
lt_note_text LIKE STANDARD TABLE OF soli WITH HEADER LINE,
lt_attachments LIKE STANDARD TABLE OF sood5 WITH HEADER LINE.
DATA: lt_objcont LIKE STANDARD TABLE OF soli WITH HEADER LINE,
lt_objhead LIKE STANDARD TABLE OF soli WITH HEADER LINE.
DATA: pdf_format LIKE STANDARD TABLE OF tline WITH HEADER LINE.
TYPES: BEGIN OF y_files,
file(60) TYPE c,
END OF y_files.
DATA: lt_files TYPE STANDARD TABLE OF y_files WITH HEADER LINE.
DATA: l_objcont LIKE soli OCCURS 0 WITH HEADER LINE.
DATA: l_objhead LIKE soli OCCURS 0 WITH HEADER LINE.
STRUCTURES
DATA: folder_id LIKE soodk,
object_id LIKE soodk,
link_folder_id LIKE soodk,
g_document LIKE sood4,
g_header_data LIKE sood2,
g_folmem_data LIKE sofm2,
g_header_data LIKE sood2,
g_receive_data LIKE soos6,
g_ref_document LIKE sood4,
g_new_parent LIKE soodk,
l_folder_id LIKE sofdk,
v_email(50).
DATA: hd_dat LIKE sood1.
VARIABLES
DATA: client LIKE tst01-dclient,
name LIKE tst01-dname,
objtype LIKE rststype-type,
type LIKE rststype-type.
DATA: numbytes TYPE i,
arc_idx LIKE toa_dara,
pdfspoolid LIKE tsp01-rqident,
jobname LIKE tbtcjob-jobname,
jobcount LIKE tbtcjob-jobcount,
is_otf.
DATA: outbox_flag LIKE sonv-flag VALUE 'X',
store_flag LIKE sonv-flag,
delete_flag LIKE sonv-flag,
owner LIKE soud-usrnam,
on LIKE sonv-flag VALUE 'X',
sent_to_all LIKE sonv-flag,
g_authority LIKE sofa-usracc,
w_objdes LIKE sood4-objdes.
DATA: c_file LIKE rlgrap-filename,
n_spool(6) TYPE n.
DATA: cancel.
DATA: desired_type LIKE sood-objtp,
real_type LIKE sood-objtp,
attach_type LIKE sood-objtp,
otf LIKE sood-objtp VALUE 'OTF', " SAPscript Ausgabeformat
ali LIKE sood-objtp VALUE 'ALI'. " ABAP lists
CONSTANTS
CONSTANTS: ou_fol LIKE sofh-folrg VALUE 'O',
c_objtp LIKE g_document-objtp VALUE 'RAW',
c_file_ext LIKE g_document-file_ext VALUE 'TXT'.
*=======================================================================
*=
*=========
*z_send_email_fax2
*function z_faian_mail_fax2.
""Interface local:
*" IMPORTING
*" REFERENCE(SRC_SPOOLID) LIKE TSP01-RQIDENT
*" REFERENCE(FAX_MAIL_NUMBER) TYPE SO_NAME
*" REFERENCE(HEADER_MAIL) TYPE SO_OBJ_DES
*" REFERENCE(OBJECT_TYPE) TYPE SO_ESCAPE
*" TABLES
*" LT_BODY_EMAIL STRUCTURE SOLI
*" EXCEPTIONS
*" ERR_NO_ABAP_SPOOLJOB
Fist part: Verify if the spool really exists
*select single * from tsp01 where rqident = src_spoolid.
DATA src_spoolid TYPE tsp01-rqident VALUE '23242'.
DATA header_mail TYPE so_obj_des.
DATA lt_body_email TYPE STANDARD TABLE OF soli WITH HEADER LINE.
DATA l_t VALUE '1'.
header_mail = 'Subject line of mail'.
IF l_t = '1' .
RAISE err_no_abap_spooljob. "doesn't exist
*ELSE.
client = '200'."tsp01-rqclient.
name = 'SPOOL0000023242'."tsp01-rqo1name.
CALL FUNCTION 'RSTS_GET_ATTRIBUTES'
EXPORTING
authority = 'SP01'
client = client
name = name
part = 1
IMPORTING
type = type
objtype = objtype
EXCEPTIONS
fb_error = 1
fb_rsts_other = 2
no_object = 3
no_permission = 4
OTHERS = 5.
IF objtype(3) = 'OTF'.
desired_type = otf.
ELSE.
desired_type = ali.
ENDIF.
CALL FUNCTION 'RSPO_RETURN_SPOOLJOB'
EXPORTING
rqident = src_spoolid
desired_type = desired_type
IMPORTING
real_type = real_type
TABLES
buffer = l_objcont
EXCEPTIONS
no_such_job = 14
type_no_match = 94
job_contains_no_data = 54
no_permission = 21
can_not_access = 21
read_error = 54.
IF sy-subrc EQ 0.
attach_type = real_type.
ENDIF.
CALL FUNCTION 'SO_FOLDER_ROOT_ID_GET'
EXPORTING
owner = sy-uname
region = ou_fol
IMPORTING
folder_id = l_folder_id
EXCEPTIONS
OTHERS = 5.
fill out informations about the header of the email
CLEAR: g_document.
g_document-foltp = l_folder_id-foltp.
g_document-folyr = l_folder_id-folyr.
g_document-folno = l_folder_id-folno.
g_document-objtp = c_objtp.
g_document-objdes = header_mail.
g_document-file_ext = c_file_ext.
g_header_data-objdes = header_mail.
CALL FUNCTION 'SO_DOCUMENT_REPOSITORY_MANAGER'
EXPORTING
method = 'SAVE'
office_user = sy-uname
IMPORTING
authority = g_authority
TABLES
objcont = lt_body_email
attachments = lt_attachments
CHANGING
document = g_document
header_data = g_header_data
EXCEPTIONS
OTHERS = 1.
folder_id-objtp = l_folder_id-foltp.
folder_id-objyr = l_folder_id-folyr.
folder_id-objno = l_folder_id-folno.
object_id-objtp = c_objtp.
object_id-objyr = g_document-objyr.
object_id-objno = g_document-objno.
link_folder_id-objtp = l_folder_id-foltp.
link_folder_id-objyr = l_folder_id-folyr.
link_folder_id-objno = l_folder_id-folno.
REFRESH lt_rec_tab.
CLEAR lt_rec_tab.
lt_rec_tab-sel = 'X'.
lt_rec_tab-recesc = object_type. "This field for FAX/MAIL
lt_rec_tab-recnam = 'U-'.
lt_rec_tab-deliver = 'X'.
lt_rec_tab-not_deli = 'X'.
lt_rec_tab-read = 'X'.
lt_rec_tab-mailstatus = 'E'.
lt_rec_tab-adr_name = fax_mail_number.
lt_rec_tab-sortfield = fax_mail_number.
lt_rec_tab-recextnam = fax_mail_number.
lt_rec_tab-sortclass = '5'.
APPEND lt_rec_tab.
lt_rec_tab-recextnam = ."Email id .
lt_rec_tab-recesc = 'U'. "object_type.
lt_rec_tab-sndart = 'INT'.
lt_rec_tab-sndpri = 1.
APPEND lt_rec_tab.
c_file = 'C:\Documents and Settings\abgupta\Desktop\Abhinav\zpk.txt'.
lt_files-file = c_file.
APPEND lt_files.
begin of insertion by faianf01
hd_dat-objdes = header_mail.
CALL FUNCTION 'SO_ATTACHMENT_INSERT'
EXPORTING
object_id = object_id
attach_type = attach_type
object_hd_change = hd_dat
owner = sy-uname
TABLES
objcont = l_objcont
objhead = l_objhead
EXCEPTIONS
active_user_not_exist = 35
communication_failure = 71
object_type_not_exist = 17
operation_no_authorization = 21
owner_not_exist = 22
parameter_error = 23
substitute_not_active = 31
substitute_not_defined = 32
system_failure = 72
x_error = 1000.
IF sy-subrc > 0.
ENDIF.
end of insertion by faianf01
lt_note_text-line = 'test prgram for email'.
APPEND lt_note_text.
send email from SAPOFFICE
CALL FUNCTION 'SO_OBJECT_SEND'
EXPORTING
folder_id = folder_id
object_id = object_id
outbox_flag = outbox_flag
link_folder_id = link_folder_id
owner = sy-uname
check_send_authority = 'X'
TABLES
receivers = lt_rec_tab
note_text = lt_note_text
EXCEPTIONS
active_user_not_exist = 35
communication_failure = 71
component_not_available = 1
folder_no_authorization = 5
folder_not_exist = 6
forwarder_not_exist = 8
object_no_authorization = 13
object_not_exist = 14
object_not_sent = 15
operation_no_authorization = 21
owner_not_exist = 22
parameter_error = 23
substitute_not_active = 31
substitute_not_defined = 32
system_failure = 72
too_much_receivers = 73
user_not_exist = 35.
ENDIF.
COMMIT WORK AND WAIT.

Hi!
Add the actual body right after the line, you have created the Multipart object.
// create and fill the first message part
MimeBodyPart mbp1 = new MimeBodyPart();
mbp1.setText(this.text); //body of message
Multipart mp = new MimeMultipart();
// Adding the body
mp.addBodyPart(mbp1);
//adding attachments
//... and so on...-Raine-

Exchange Mail on Local LAN

Similar Messages

Maybe you are looking for