Fast instruction Access MMU miss

Hello,
Trying to install solaris 9, 4/04 and get fast instruction access mmu miss.
Then I also get this:
ERROR: Could not open file (/a/etc/vfstab)
ERROR: Could not create the file system mount table (/etc/vfstab)
ERROR: System installation failed
and my vfstab looks like this:
#device device mount FS fsck mount mount
#to mount to fsck point type pass at boot options
/proc - /proc proc - no -
fd - /dev/fd fd - no -
swap - /tmp tmpfs - yes -
swap - /tmp tmpfs - no -
/proc - /proc proc - no -
/devices/pci@1e,600000/ide@d/sd@0,0:b - / ufs - no ro
/devices/pci@1e,600000/ide@d/sd@0,0:a - /cdrom hsfs - no ro
fd - /dev/fd fd - no -
Very strange. Could someone help me? What should I do?
BR Nadia

I think it is something to do with your boot-device bring it down to 'ok'
Run printenv to see the boot devices.
ok printenv boot-device
boot-device = disk disk2 net
Run the devalias command to see the path for the boot-device:
ok devalias disk
disk /sbus/espdma@e,8400000/esp@e,8800000/sd@0,0
Review the path to ensure that it is the correct path to the boot device.
For example, if the path came back:
disk /sbus/espdma@e,8400000/esp@e,8800000/sd@0,0:c
The :c is telling you slice 2. Usually slice 2 is the backup slice and is the entire disk, not just the root slice. Hence, the device alias is improperly set for root.
To find out what the correct path is, boot the system to single user from cdrom, then type 'format' to find which slice is the correct root partition, then try to manually mount it.
say for example you find that slice '0' is the correct partition then umount and init 0 to go back to 'ok'
then do a nvalias
disk3 /sbus/espdma@e,8400000/esp@e,8800000/sd@0,0:a
then boot and try again

Similar Messages

Solaris 8 07/01 installation : Fast Data Access MMU Miss

hello,
Because of a hardware crash of my 9.1Gb hard drive, I plugged a brand new 40Gb drive in my Ultra 10 workstation.
I tried to re-install my release of Solaris 8 (06/00), but this release detect only a 5Gb hard drive (but the installation work).
I downloaded and burned Solaris 8, release 07/01 to break the 32Gb/drive limit, but when I type 'boot cdrom' or 'boot cdrom install' at the bios prompt, I get :
Fast Data Access MMU Miss.
I upgraded the PROM to the lastest version, and tried to reburn the CD.
Does someone has any idea to help me ?
Greg.

974009 wrote:
Hello all,
I have been working on a Sun Netra T1 105 for the past two weeks That system is too old for Solaris 11 and Solaris 10. That generation UltraSPARC module isn't going to be recognized by those newer OS's.
I suggest you go to your preferred online auction web site (for example, eBay) and get any Solaris 8(SPARC) or Solaris 9(SPARC) for that little 1U box.
I have disabled auto boot so when it starts it is going to the ok prompt.Smart. Good move for troubleshooting.
The CD of Solaris 11 is a new one that I burned just two weeks ago and I burned it on 24x speed.
And it is the Sparc version that I downloaded.
I also tried installing a DVD-ROM with the Solaris 10 DVD but it gave the same error.I hope that means you replaced the original CD reader with a DVD-capable drive.
When I type probe-ide it shows that the seconday Master is a Removable ATAPI Model: TOSHIBA CDROM XM-7002BcYes. Since that model computer was discontinued in 2002, there was only a CD-capable drive ever qualified to be used in it.
When I type probe-scsi it shows:
Target 0
Unit 0 Disk Seagate ST39103LCSUN9.0G034AA 9GB disk isn't going to be large enough for much more than just a core install of Solaris. You may again need to get larger drive(s) at that same online auction web site. The chassis can hold two internal disks.
Thank you very much.
Hendrik
Edited by: 974009 on 29-Nov-2012 07:34When you get the chance, glance at this link to a copy of the Netra T105's resource page as it appeared in the old Sun System Handbook (SSH). The link is to a non-Oracle site that mirrors the old now-discontinued free version of that SSH.
Next, while there's not much system documentation for that box offered by Oracle, you can glance through what there happens to be here:
http://docs.oracle.com/cd/E19628-01/index.html

SAP-MM CIN Error: JTAX Access sequence missing at the time of excise invoice creation in J1IS

Dear Sir,
During creation of excise invoice with ref to material doc system give a error massage JTAX access sequence is missing. Access sequence and tables are already exist in system.
1.PO
2. GR with excise capture& post here Part-I&II are genarated.
3.Invoice
4.Return delivery with reference to above goods receipt document.(122 m.type)
5. J1IS- Creating outgoing excise invoice w.r.to return delivery material document.
JTAX Access sequence missing at the time of excise invoice creation in J1IS

The same error coming while consignment stock issue to cost center.
1.Consignment Info record with excise tax code.
2.PO consignment purchase order.
3.GR with excise capture & post here Part-I&II documents are created.
Material document created but there is no accounting document.
4.While doing Consignment stock issue to cost center system generate an error message
Access sequence JTAX missing ( ) Message no. VE306"

Fast web access

Is it possible to have a fast web access pdf load only a specified number of pages, at least to start with? Say the top/first ten pages of a larger pdf?
I have a web site which displays a multi page pdf, which is regularly being added to; new pages go to the top on a regular basis. (It is a legal file - when a new piece of correspondence comes in, it is added to the pdf). The viewer usually only wants to view the several new pages I have added. But every time the whole document is downloaded, which in this case is a waste of the client's download limits.
I do of course enable fast web access and use Acrobat's Reduce File Size... feature. They are always black and white files. All of this helps the download speed.
If the viewer wants to view pages beyond the initial ten, then the request for page 11 could then trigger a request for another 10??
Any feedback on this issue greatly appreciated.

I use this forum on a variety of Win7 32 and 64 bit machines and I have not experienced any slowness in loading at all. I reckon that it takes less than 1 sec to load any page and at my age, that's faster than a blink of my eye. My broadband connection is a constant 6.6 Mbps using the MkII curved hub with full home network with many devices attatched (PC's, printers, NAS drives + BT vision, Blu-ray BD etc, etc.). I use IE8 on all machines and F-Secure Internet security. All machines also run MSoffice 2010 which is soooo good.
Overall, the new site is fine.
OLD MAN ( 3 x 20 + 10 and still with it! )

Advice needed on fast streaming/access from external HD (Video/Music apps)

Hello,
I'm a computer musician and have reached the max on my internal SATA drive, and thus I'm looking for an effective, extra-fast external HD capable of intense sample streaming (i.e. quickly accessing many small files from different parts of the drive at once). I'm not looking for write speed, as that does not concern me. The main concern is "read speed."
In my search I came across this eSATA drive from segate which seems to have been designed with my needs in mind: http://www.creativemac.com/articles/...e.jsp?id=53423
However, it takes PCI 2.2, while us dual G5 users only have PCI-X, correct? Does this mean this particular eSATA drive will not work in my system? Are there any eSATA drives/enclosures that were designed specifically for PCI-X? Is eSATA worth it when compared with FW800 in my line of work? (I already own a Lacie FW88 drive as a backup drive, but can switch its application if needed). What is the best technology for fast streaming/access from an external HD?
I'm sorry if this topic has already been covered, but in my search I was unable to find any topics specifically regarding this type of use of an external HD.
I thank you in advance for any help you can provide!

You probably want to look at an "e-SATA" Raid. The November ish of Macworld has a review of several "Mac friendly" units"

W500 Access Connections Missing Resource DLL Win XP Pro SP3

Hi, today is 4/21/2010.
I upgraded access connections and get this message on boot up now:
Box title: ThinkVantage Access Connections
Resource dll is missing, Reinstall the application to avoid this problem.
I have upgraded hotkeys, power management driver, access connections and intel proset wireless to the latest versions with particular care taken to follow all of the install instructions.
I cannot get this pop-up box to go away. Also, when i ask the icon in the lower right corner of the screen to "Launch Access Connections" so I can re-import my profiles.. it doesn't ever launch a window, although i can see with process explorer that an executeable called "Access Connections.exe" was launched by "ACTray.exe"
I have done a side-by-side search of a T61P and my W500 and find all of the same "resource" dlls in the same locations.
Please help. Also, if Lenovo tech support happens to read this, please put a check in all of the software upgrade packages to make sure that all the prerequisites are properly installed first. that would probably solve a lot of your problems.
Thanks
Ted

Hi,
I have seen such messages and mostly one of the following was the root cause:
- There is a virus on your system, that prohibited the full installation and registration of Access Connection
- The Access Connection could not be installed properly
The re might be also couple other options, why this might happen, but till now I faced only these situations.
Tell me, after, or priro to the error message, do you see any .dll files described, to which is can be realted?
If yes, then find those file on you HDD and make sure, that they are also present in "%windir%\system32".
Let me know, what exact version of AC are you running now?
Cheers

Cannot access Recent/Missed Calls List iPhone 3GS

Hello,
Recently, without any known change to the phone (no update, firmware, change setting, etc.) I cannot access the Recents folder (list of all calls) on the phone. This is the folder at the bottom of the phone screen when you access the phone and is listed along with the Favorites, Contacts, Keypad and Voicemail folders. Also, the phone will still display the incoming call while its ringing, but it wont show the missed call callout box you normally see when you miss calls. Caller ID still works and all other phone features work normal. Strangely enough, the little red numbers that display how many unviewed calls are in that folder still works and keeps on adding up
When I try and access that folder, I get a little screen flash and the phone goes back to the desktop screen.
This is what I have tried:
-Upgraded software to 4.3.4 The upgrade was successful. Did not fix problem.
-Backed up the phone and did a restore through itunes. Did not fix problem.
- Did a phone reset through the phone settings. Did not fix problem.
I don't know what else to do. This feature is very imporant to me.
Thanks for any help.

http://discussions.apple.com/thread.jspa?threadID=2280669&tstart=0

URGENT HELP! - Access a MISSING PERSON's account

Hello,
Someone close to me has gone missing VERY RECENTLY and we (family and friends) think that we can get important clues by checking her account (legally, of course). I couldn't find the correct way of getting in touch with Skype Support.
Is there a way of accessing an account legally?

you may need to go to your local police first, then they can contact Skype to request for possible assistance regarding this matter.
IF YOU FOUND OUR POST USEFUL THEN PLEASE GIVE "KUDOS". IF IT HELPED TO FIX YOUR ISSUE PLEASE MARK IT AS A "SOLUTION" TO HELP OTHERS. THANKS!
ALTERNATIVE SKYPE DOWNLOAD LINKS | HOW TO RECORD SKYPE VIDEO CALLS | HOW TO HANDLE SUSPICIOS CALLS AND MESSAGES
SEE MORE TIPS, TRICKS, TUTORIALS AND UPDATES in
| skypefordummies.blogspot.com |

Access logs (missing)

Hi,
I'm trying to determine when a user accessed the server via AFP. I've found /Library/Logs/AppleFileService/ logs but many are missing - only the last 2 weeks are there. I also found entries in another log deleting these files since disk was full, however it only shows logs been deleted from March (it's now November) and earlier:
Fri Oct 29 11:48:44 2010: recover: About to perform action "delete" on file "/Library/Logs/AppleFileService/AppleFileServiceAccess.log 01.18.10.gz" on critical volume "Server HD" which is 4.96% full because size 0 MB >= trigger size 2 MB or age 289 >= trigger age 2 days.
Questions:
- is there any way to tell when/if AFP logging was enabled/disabled?
- is there any other way to tell if users logged in via AFP (accessed a share)?
- any ideas why April-October logs would be missing?
Thanks!

The only other way I found would be to use :
%Req->reqpb.method% %Req->reqpb.uri% instead of %Req->reqpb.clf-request%, that way the protocol just wouldn't be logged! My log analyser (Awstats 5.6) would then be able to crunch them by NOT checking for a protocol with the %methodurlnoproto parameter in awstats.
This is causing me yet another problem. With only the URI, I don't have the querystring. Of course, it is possible to use %Req->reqpb.query%, but this isn't linked to the URI in the log. I need to hardcode a '?' between the two. Therefor, I would also get requests such as '/foo.htm?' logged.
Another problem I seem to be having when using just the URI is that iPlanet seems to get only the first 128 caracteres from the request. After that numbers, it cuts off the URI.
I'm a bit confused here on what's the best solution...
Pat.

Fusion Middleware Control "Identity and Access" menu missing

Hi.
I have a problem with one of the fussion middleware control menus which is missing.
The environment is as follows:
- One server with OVD + OID
- One server with Weblogic + ODSM + Fussion Middleware Control
(All idm fmw 11.1.1.2.0)
ODSM can connect to OVD / OID on the other server without any problems.
On Fussion middleware Control I can not see the menu "Identity and Access". In previous installations where all the components where installed together in the same server, that menu appeared without any extra configuration.
The menu i'm talking about is the one referred here: http://download.oracle.com/docs/cd/E15523_01/oid.1111/e10046/basic_started.htm#CIHHAJJH
"2.In the left panel topology tree, expand the farm, then Identity and Access. Alternatively, from the farm home page, expand Fusion Middleware, then Identity and Access. Oracle Virtual Directory components are listed in both places"
Which are the steps to get that menu back? How do i get "linked" fusion middleware control with ovd/oid from the other server?
Any extra configuration, any steps during installation...
There's something probably very simple i'm missing but i haven't found any reference about creating/configuring that menu...
Thanks in advance.

Hi. i tried what i posted on my last message but i can't pass next step of the installation.
If i try to install oid+ovd in <host 2> i can select "extend existing domain" and it connects correctly to the weblogic domain (IDMDomain creating during installation of odsm & em fmw control) that is up un running on <host 1>.
But on the next step it asks for the "Weblogic Server Directory"... If i enter the path where weblogic resides on <host 1> it fails because it looks for it in the host i'm installing oid+ovd <host 2>.
- First of all, is it really possible to have oid+ovd on one host and weblogic+odsm+enterprise manager fmw control in a different host in a way that makes possible to manage oid+ovd with enterprise manager fmw control?
- Is it possible to tell the installer that the path for the weblogic server is in a different host? something like host:path?
- If it's not possible, is it documented anywhere? i haven't found anything regarding that possible limitation.
Please, any help would be appreciated as this is becoming critical for us.

Quick access to missed calls in call log

I have a Palm Centro (Sprint). How can I set up quick access to the Missed Calls in the Call Log? On what many would consider a much inferior phone, my old Sanyo Katana, Missed Calls access could be set up as a quick link and available by the push of one button. On what many would consider a superior phone, the Palm Centro, it takes eight pushes to get to the Missed Call logs.
Can anyone help me get back that one-button-push functionality and set it up on my Centro? Quick access to the Missed Calls log is very important to me.
Thanks, Mike
Post relates to: Centro (Sprint)

Unfortunately, there is no method to remap the missed call log to another button natively on the Centro.
There may be a 3rd party app. available that you can install that will accomplish what you are wanting to do.
For reference purposes, click on the following link for the support page for your device on the kb.palm.com webpage.
http://kb.palm.com/SRVS/NUA/launchTab.asp?t=home&fn=centro&mn=centro&cn=sprint
There are links on the page to the user guide, troubleshooting, how to's, downloads, etc.
Post relates to: Palm i705

Address book from Palm Desktop by Access is missing on computer!

Please help - My address book from my Palm Desktop by access is GONE - I can find only a "address.mdb" file, but no updated .aba file - Is there a way to restore this file or find a backup? I cannot imagine how it just disappeared! I no longer use the Zire handheld as it broke, please help!
Thank you

If Thunderbird will accept .csv or .tab file formats you can export the data in those formats from PD. Use the following procedure to export your data.
The best way to preserve your data is to export the data in each category in Palm Desktop to a seperate folder on your PC.
Create a new folder on your PC somewhere that is convenient. Name it something like Palm Desktop Data. Click on the link below and follow the instructions on that page for the export procedure.
http://www.palm.com/cgi-bin/cso_kbURL.cgi?ID=28734
Make sure you select all for the range in the export window.
With the data saved in the folder you created, make a copy of that folder and save to a flash drive, cd-rw or external hard drive.
Anytime you make a change in Palm Desktop, export the data that was changed to that folder and save again to the external media.
With this process you can always import the data back into Palm Desktop anytime you have a problem with the data in Palm Desktop or if your computer/hard drive/device crashes.

I haven't been on itunes in a very long time. I had a lot more songs than are there now. What can I do about it, or is there a way to access the missing songs?

I haven't been on itunes in a very long time. I had a lot more songs than there are listed there now. What can I do about it, or is there something I can do to get the missing songs back?

forget about it, I actually figured it out.

MsAccess - Oracle10g : decimals from a NUMBER field in Access are missing

Hi,
Using Oracle10g - Oracle 9i ODBC driver - MsAccess
When I link a table in MsAccess, the decimals from a Oracle NUMBER(14,3) field do not show in Access.
(e.g. 123.45 in the Oracle DB is shown as 12345 in Access. )
Hope you can help.
Linde Ackermans

Problem solved : it was only a matter of wrong NLS_LANG value ( again )

Converting SQL Server query to access join missing operator issue

The RIGHT JOIN without and ON clause is throwing me. I cannot figure out where access is wanting the parenthesis in the join syntax this query:
SELECT DISTINCT *
FROM CANDIDATE_RECRUITERS
INNER JOIN CANDIDATE_EVENTS
ON CANDIDATE_RECRUITERS.RecruiterNum = CANDIDATE_EVENTS.Recruiter
RIGHT OUTER JOIN CANDIDATE_CUR
INNER JOIN CANDIDATE_JOB_TITLES
ON CANDIDATE_CUR.JobTitle = CANDIDATE_JOB_TITLES.TitleID
INNER JOIN CANDIDATE_COMPANY_CUR
ON CANDIDATE_CUR.CompanyNum = CANDIDATE_COMPANY_CUR.CompanyNum
ON CANDIDATE_EVENTS.CandidateNum = CANDIDATE_CUR.CandidateNUM

Try this:
SELECT *
FROM (((Candidate_Recruiters
LEFT JOIN Candidate_Events
ON Candidate_Recruiters.RecruiterNum = Candidate_Events.Recruiter)
RIGHT JOIN Candidate_Cur
ON Candidate_Recruiters.CandidateNum = Candidate_Cur.CandidateNum)
INNER JOIN Candidate_CurCompany
ON Candidate_Cur.CompanyNum = Candidate_CurCompany.CompanyNum)
INNER JOIN Candidate_Job_Titles
ON Candidate_Cur.JobTitle = Candidate_Job_Titles.TitleID
Matthias Kläy, Kläy Computing AG

Fast instruction Access MMU miss

Similar Messages

Maybe you are looking for