Flashing Finder Icon/ Question Mark on Boot

Today I left my 1.33ghz G4 Mac Mini turned on whilst I went to the shop.
When I came back i found it eith a flashing finder icon/ question mark.
I restarted it and it booted up a grey screen, then after a while the flashing finder icon/question mark.
I have tried putting in the OSX install disc and holding down the C key to start up using the CD and nothing happen, all I get is the same grey screen and flashing icon.
I have also tried pressing the X key, and holding it down and restarting to get up the startup disk menu, but again nothing.
Pressing 'option' key during start up only gets me a blue background with refresh button on the left and right arrow on the right - with no Boot Up CD or HDD Icon.
I have also tried resetting the PRAM, it resets, but after it hasn't solved my problem, as i am back to square one with the boot screen and icon.
Any help would be appreciated.
Thanks,
big.bad.ben

I would agree with DP that using a wired keyboard will give better results when holding down the C key. The timing of holding down the C key is tricky, and you might have to experiment with it.
The question mark means that the Mini can't find a bootable disk. Usually this is because the internal hard drive has enough directory damage that it is not bootable. Usually this can be fixed by reformatting the internal drive or replacing it.
But if you truly can't boot from the install CD, that suggests a more serious problem with the logic board or RAM memory.
When you power-up the mini, do you get a series of beeps or light flashes? The pattern of such beeps/flashes is a diagnostic aid to determine what might be wrong. Report back with what pattern you observe.
Be sure to give the install CD some more tries, varying the timing of holding down the C key. Usually you want to do it right after the startup chime.

Similar Messages

I have a 2005 g5 2.5 2g ram will not boot up ,blue screen with folder with finder icon question mark. have tried to boot from dvd disc by holding down ckey but all i get is apple logo and fans start running really fast.have tried hard drive in identcal g5

tried hard drive in another g5 but with the same result.can anybody suggest what might be wrong

had the same result on other g5 blue screen finder folder with question mark. i put the hard drive in the bottom bay of my g5 after and ran disk repair said disk ok .reparaired permissions tried hard drive in top bay again but with same result.
do i just disconnect the two connections on hard drive and then try your second suggestion?

Unable to boot - flashing finder icon with question mark.

Hi all,
I just got a friends old xserv G5 to learn Mac and the server suite on. He gave me the OSX Server install disk (10.5 I believe) with the license keys.
I get the XServe into "Target Disk Mode" by turning it on holding T and plugging my friends Intel Pro MacBook into it VIA FireWire. We install the Server 10.5 to the Server Disk fine, no issues. All options checked. Then upon reboot we shutdown everything and try to boot the server up on it's own and then this is where we get the flashing finder icon problem...
Here's what we've tried:
I think the Firmware is locked because when I try to power on holding power + system identifier button, both rows flash instead of the one, here's what I've done
Tried removing a memory module, booting with command, alt, p + r, no effect.
Clear NVRM by pressing button behind PSU on mainboard of xserve. No effect.
Unplugging and removing battery for minute, to clear. No effect.
I guess what I'm trying to do is clear the firmware lock so I can direct the xserve to select the startup disk by pressing F1 / D as I'm assuming that's what the issue is?
Any thoughts?

I'm not sure about the dl-DVD thing. I'm trying to remember how I installed 10.5 on my G5 boxes (it's been a while) and I know I used the Administrator computer as described in the Getting Started guide, but I don't remember if I imaged the DVD to a firewire drive.
The easiest short-cut for that is to image the DVD onto a firewire drive and attach that to the Xserve and run it as the install media. It's much faster to install this way as well. Use Disk Utility to image the DVD onto an external firewire and then boot holding down the option key - choose the drive and then use the notebook as an "Administrator computer" as described in the guide. The only hold-ups are the IP space issues and make sure you know the Xserve serial number. In theory I think you can also use another computer with the DVD in the drive running in firewire mode but now you're up to three computers instead of 2 plus a firewire drive.
I've never been a fan of the notebook>>Xserve install process even before architecture issues arose. The Xserve has special hardware monitoring capabilities that you would lose when installing booted from a non-Xserve box. I know 10.5 was supposed to install a "global" image that would run on both platforms but I wouldn't trust it even if they said you could.
HTH,
=Tod

Dreaded Gray screen with Folder and Question Mark (EFI Boot poofs away)

Hey--
I've had trouble with my Imac that I purchasd in 2005 for a year and a half or so. I had a gray screen about a year and a half ago, went on vacation for a week, came back and it booted just fine. Another time it went down, I did a safe boot and it came back. I've tried Command-Option P+R before with some success. I had a boot camp partitioned windows xp drive on there also (I don't know if this matters, but wanted to mention that). I've also tried putting the installation disk in there with no luck (thinking it would find the software on it)
I put it away because I moved and dragged it out of storage to see if a miracle might have occured since the last time I tried 5 months ago. Well, same thing--gray screen with a flashing folder with question mark. I read in the discussions to hold the option key down to select a book device. I tried this and got an EFI Boot icon with a mouse pointer, but when I go to select it it "poofs" away (literally, the icon POOFS away) before I can select it with the mouse pointer icon.
Has anyone seen anything like this or have any suggestions? I guess I'm at my wits end and am ready to haul it down to the Apple store to get the prognosis (I'm sure it will not be good--probably shot hard drive or something). I'm hoping this can be salvaged without much cost.
Thanks so much for any advice or input you might have.
Chris

How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.
If yours is an Intel model, then I recommend getting Snow Leopard to upgrade OS X, but I would recommend first erasing the drive before installing Snow Leopard.
Upgrade Paths to Snow Leopard, Lion, and/or Mountain Lion
You can upgrade to Mountain Lion from Lion or directly from Snow Leopard. Mountain Lion can be downloaded from the Mac App Store for $19.99. To access the App Store you must have Snow Leopard 10.6.6 or later installed.
Upgrading to Snow Leopard
You can purchase Snow Leopard through the Apple Store: Mac OS X 10.6 Snow Leopard - Apple Store (U.S.). The price is $19.99 plus tax. You will be sent physical media by mail after placing your order.
After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mountain Lion if your computer meets the requirements.
     Snow Leopard General Requirements
       1. Mac computer with an Intel processor
       2. 1GB of memory
       3. 5GB of available disk space
       4. DVD drive for installation
       5. Some features require a compatible Internet service provider;
           fees may apply.
       6. Some features require Apple’s iCloud services; fees and
           terms apply.
Upgrading to Lion
If your computer does not meet the requirements to install Mountain Lion, it may still meet the requirements to install Lion.
You can purchase Lion by contacting Customer Service: Contacting Apple for support and service - this includes international calling numbers. The cost is $19.99 (as it was before) plus tax. It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
     Lion System Requirements
       1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
           or Xeon processor
       2. 2GB of memory
       3. OS X v10.6.6 or later (v10.6.8 recommended)
       4. 7GB of available space
       5. Some features require an Apple ID; terms apply.
Upgrading to Mountain Lion
To upgrade to Mountain Lion you must have Snow Leopard 10.6.8 or Lion installed. Purchase and download Mountain Lion from the App Store. Sign in using your Apple ID. Mountain Lion is $19.99 plus tax. The file is quite large, over 4 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
     OS X Mountain Lion - System Requirements
       Macs that can be upgraded to OS X Mountain Lion
         1. iMac (Mid 2007 or newer) - Model Identifier 7,1 or later
         2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) - Model Identifier 5,1 or later
         3. MacBook Pro (Mid/Late 2007 or newer) - Model Identifier 3,1 or later
         4. MacBook Air (Late 2008 or newer) - Model Identifier 2,1 or later
         5. Mac mini (Early 2009 or newer) - Model Identifier 3,1 or later
         6. Mac Pro (Early 2008 or newer) - Model Identifier 3,1 or later
         7. Xserve (Early 2009) - Model Identifier 3,1 or later
To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
     Are my applications compatible?
         See App Compatibility Table - RoaringApps.
     For a complete How-To introduction from Apple see Upgrade to OS X Mountain Lion.

Flashing folder with question mark at Startup

Here is what I know so far.
- The computer was powered off by pushing the power button without shutting down.
- The computer was then restarted and it was coming into the white screen with the Apple logo in the middle, but i noticed that it was skewed slightly (like someone took a 4:3 ratio screen and stretched it to a 16:9) and then it would show a circle slash icon and then the flashing folder with a question mark on it.
- It would not come up in single user mode (Command + S) and it said that there was an error loading kernel 'mach_kernel'
- It would not come up in safe mode (Shift)(The flashing folder came up again)
- I reset the PRAM (Command + Option + p + r) and it seemed to fix the problem with the stretched screen but did not help the boot situation (still got flashing folder)
- I did the start up where you can select the hard drive to boot with, it owed the HD and i selected it, but then i got the flashing folder with question mark.
- It would not come up in Verbose Mode (Command V) Error loading Kernel again.
- I bought a FireWire cable and hooked it to another MacBook Pro, and booted the faulty Mac into Target Disk Mode, the FireWire logo came up on the screen and bounced around like all forums said that it would, but the drive would not show up on my host. I checked the System Profiler on the host and it did acknowledge the Target Disk Mode was there, but the drive of the target would not show up on the host. I restarted the host, nothing. I checked all of the connections, nothing. I replugged all of the connections, nothing. I even reversed the FireWire cable, nothing.
- I have DiskWarrior 4 if i can get the drive to show up in TDM, but nothing so far.
Does anyone have any suggestions?

Thanks for your help guys. I managed to get the computer started by holding down C at the Start Up with the Install Disc 1 in the computer. The disc was really kindof unnecessary, as the newest version of Mac OS X (10.4.10) became available via the hard drive.
I then found out that the battery was not installed, so I reset the management system by removing the A/C power, the battery and pushing the power button for 5 seconds, and then reconnecting everything. It did not help, the battery is bad i guess, so I am going to call AppleCare and get a new battery.
Thanks for your help.

HT1366 How to fix Flashing Folder with Question Mark on Mac

How to fix Flashing Folder with Question Mark on Mac

RichardEL is probably correct. I’ll go through your questions.
> there is no Mac OS partition, I assume it would be directly underneath the HD on the left?
I have not seen this particular condition where the hardware disk icon appears but the system volume that is supposed to be below it does not. The System Disk partition would be below the HD icon indented to the right. It is usually called “Macintosh HD” unless you renamed it.
> when I go into disk utility my HD appears on the left, but I can repair or verify it
Odd. It appears but you cannot manipulate it with Disk Utility.
> The S.M.A.R.T status reads verified
If it did not say Verified then it would indicate a problem. Saying Verified does not rule out problems but I think it indicates it is still breathing.
> Is the HD deceased?
If you booted the Recovery Partition (Boot, Command-R), which it sounds like you did, then at least part of the disk is still breathing. If it took a long time to boot then that may have been a Network Recovery boot which would indicate the disk is very sick or dead.
> [If I] restore from time machine [will] everything will be back as it was before?
Yes. That is the beauty of Time Machine. All your data, applications, and system preferences will be as they were as of the last backup.
> I was thinking of erasing the HD, would this be of any help or do I just need a new one?
Given what you reported from the Disk Utility steps you took it is unclear to me if there will be a way to repair the current volume, if you can erase and install from scratch or if you need a new disk. Before proceeding it may be useful to have an expert at an Apple store look at it for you. They may be able to revive it without a clean install or new disk.
As was the case above, it could be a good disk with a bad cable in which case a new disk is not going to help. To test this you can purchase an inexpensive external enclosure, remove the internal disk, place it in the enclosure, plug it in and then use Boot-Option to attempt to boot from the now external disk. Here are links to the screwdrivers and enclosure you would need.
$5 Toolkit: http://eshop.macsales.com/item/OWC/TOOLKITMHD/
$22 USB 3.0 enclosure: http://eshop.macsales.com/item/OWC/ES2.5BU3W/
If you attempt a clean install, use the Partition tab to repartition the disk, selecting one partition and with “Options…” electing a GUID partition. Then use the Erase tab, select “Security Options…” and set it to write a single pass of zeros. This will write to every sector to map out bad blocks. (If you have an SSD do not write a pass of zeros.)
If you do need to replace it I recommend an new inexpensive (~$100) and super-fast hybrid SSHD drive that has an 8 GB SSD cache that makes the data fly. Google “Seagate 1 TB hybrid SSHD”.

Flashing Folder with Question Mark after Trackpad 1.0 Update

My machine won't boot after installing this update. I get the flashing folder with question mark and can't even boot from the Install DVD either... I just get a frozen spinney wheel at the Apple Logo screen. I've tried resetting the PRAM and everything else that a Googling of the problem suggests. This update bricked my Macbook!!!!
Anybody else having this problem? Anybody have any suggestions or am I stuck with going to see a "genius"?

I've not seen any other posts about it causing problems, worked fine here. You've tried resetting the PRAM the only other thing you could try is:
Boot holding down Apple/S and don't let go until you see scrolling text.
When that stops and you see a root#: prompt enter
fsck -fy
Let it run through all the checks and repairs.
If it fails first time, at any time, or finds and fixes a fault - run the command again and keep doing so (some fixes can take several passes) until it says "Appears to be OK" then enter
reboot

Flashing Folder and Question Mark, no installation disc

Yesterday, Safari froze up while I was it which I have never had happen before. So, I manually shut my Macbook off and tried to restart. When I did so, I received a gray screen with a flashing folder and question mark. From my research, I have found that usually this means that my laptop can't find the operating system and this issue can usually be resolved by inserting the installation disc. Problem is, I bought my Macbook secondhand and never got an installation disc. Does anyone know of a way around this issue? Or if buying the Snow Leopard upgrade for $30 instead of buying a whole new package for about a hundred dollars more might resolve this issue?
Thanks so much,
Kristin

Yes, quite a quandary. You have some options:
1. Call AppleCare and ask for customer support. You can order replacement discs for the model you have.
2. Purchase an OS X retail installer suitable for your model, like Snow Leopard, that you can use to determine if you can repair the hard drive or will nee to reinstall OS X. If the latter and you are using Snow Leopard, then you just install it. The installer will determine whether to upgrade or not automatically. As long as your drive is OK Snow Leopard will not erase the drive so all your files are safe. If you use an earlier version of OS X then you want to choose the Archive and Install option. See the following:
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then quit DU and return to the installer.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

Flashing folder with question mark comes up at startup?

it was working fine 3 days ago i try start it up and a Flashing folder with question mark.
It has mountain lion i try to boot to recovery Part but when i hold the Option key nonthing show up.
If some can tell me what else i can.

restart holding command R if it can not find a Recovery partition it will do a Internet Recovery.
Run diskUtility "repair disk" from the recovery.
http://support.apple.com/kb/HT4718

Flashing folder with question mark (MacMini)

Hi there,
I diagnose my Mac Mini (1.83Ghz, Intel Mac) and know that the HDD is failing, so I decide to change the HDD before the HDD totally fail.
But after I change the new HDD, and trying to install the OS back to the new HDD, I get a flashing folder icon with question mark in it, when I boot it up and press on the C key to boot from CD. So I decide to take the new HDD back out, put in an external enclosure to make sure that the new HDD is not a bad one, and I can read fine with it inside the enclosure, put it back in the Mac Mini, still the same old flashing icon.
What happen? Could someone help me please?
Thanks!

Hi Everyone,
Just for future reference for anyone who encounter this same problem, the reason that I go the flashing folder with question mark is first of all, the MacMini doesn't recognize the new hard drive. No doubt about that since the hard drive has no OS and not formatted yet. Second of all, it's because I don't have the correct Installer CD put in. I didn't know if there's any difference in the Installer CD between PowerPC MacMini and Intel MacMini, but obviously there is, since the Intel MacMini doesn't recognize the PowerPC Installer CD.
After putting the correct Installer CD in, everything works just the way it should.
Thanks for all your help, everyone!
- NyCCD

Netboot will not working, getting globe, then flashing folder with question mark.

I just created a netboot image which went off without any problems. I copied the two .nbi folders to my NetBootSP0 folder, and enabled them within netboot. My OS X server which is my netboot server and dhcp server. When I boot using N or Option N, I get the flashing globe for several seconds, the request goes through to the server and gets ACK {SELECT} however a few more seconds after, I get the flashing folder and question mark before it does a normal boot. I have read the other posts about DHCP and Subnets. My server and and clients are all 255.255.0.0. Any suggestions would be very helpful as I need this to work for several buildings.

This might work for some:
I had the same problem of the netboot image not mounting/opening, spinning globe then booting back to the Mac HD on the client and it was only when I remembered that we had manually experimented with jumbo frame rates and the MTU settings for our 32TB RAID in the Hardware settings for Ethernet ports on our servers. I turned the settings back to "Automatic" and 1000baseT on, then the whole NetInstall and Neboot was working perfectly again.

My Macbookpro will not start up. At first it was showing a gray screen with a flashing folder and question mark. I went through the steps to repair with disc utility and this did not work. How do I back up my data, without time machine activated?

I need to back up my files and date before erasing my drive, but my time machine backup is not coming up. How do I access my hard drive to back up my files?

A erase of the drive or boot partition is not always necessary.
Flashing question mark at boot could be a easy fix, sometimes it's the firmware that simply forgot what bootable volume to boot from.
Try holding the Option key down while booting the machine, a choice of bootable options appears, select your OS X and boot up.
When you get in, head to System Preferences > Startup disk and set it again new. This will tell the firmware what to boot from. Test it to see.
Now if you don't have a selection of bootable options, it could be that the drive is dead, or OS X is erased or corrupted so it can't boot.
You'll have to run through this list of fixes to see what's going on, if you need a hardware fix or what, I've also included links if you can't fix it and need to recover your data etc.
(If it's not remmebering your boot selection then also run through the list to reset things.)
Step by Step to fix your Mac

Blue screen with flashing folder and question mark on startup

Hello.
I need help with my Macbook Pro. I get a blue screen with a flashing folder and a question mark at start up. To date I have tried the following:
Apple Hardware (Extensive) Test (Results: "No Trouble Found")
Safe Boot
Reset NVRAM
Reinstall OS X via the internet (I received no discs when I purchased it). I select the StartUp Disk to reinstall. When reinstalling via the internet I get to a point of reinstalling Mountain Lion but it asks me to choose a drive - yet there are no drive options to choose from. Then a window comes up asking me to "Select the system you want to use to start up your computer" but no options appear. When I choose "Restart" a note pops up saying "You can't change the startup disk to the selected disk. Startup Disk could not gather enough information on the selected disk."
The only option is "Restart" from the Apple menu. When I choose that it goes back to the original "Blue screen with flashing folder and question mark on startup."
I have no Time Machine
I can't access the disc utility.
Are there any ideas as to what might be the problem?

Your hard drive has likely failed and needs replaced. That would explain why the system does not display it when you attempt to reinstall the OS via Internet Recovery.

Flashing folder with question mark on start up + many other issues

About 6 months ago I first encountered the flashing folder with question mark on startup. I fixed the issue myself by unplugging the mouse and keyboard and rebooting. I also did the cmd S fsck -fy before that and all was well.
The other day I had the flashing folder again...I got it going a couple of times but it happened again. Right now I seem to be in deep trouble. Please read the following:
1. I booted up from the leopard dvd and no hard drive was there to run a disk utility on
2. Booted up again from the dvd and hard drive was there. Ran the disk utility and everything was fine...for about 5 minutes. Then the computer froze and I had to hard power down. Rebooted to the flashing folder.
3. Did command s and fsck but at the end I get the message failed to issue comm reset after 3 attempts.....failing....
4. I powered down, vacuumed out the vents, sprayed compressed air to make sure it wasn't over heating from dust buildup as I read somewhere.
5. Booted up...worked for about 5 minutes again.
6. Now I can't get to the hard drive from the install dvd at all...I tried 100 times. Cmd s won't work at all!! So it looks like I am out of options. Does anyone have ny radical solutions that i can try to fix this. There are some very important things on my hard drive that I would be very upset about loosing.
Please reply

Sorry to bear bad news, but most likely the drive is already dead or dying. I hope you backed up everything when the first symptoms appeared.
There are data recovery services, but might be very expensive.
EDIT: Some (a few) people have had success putting the drive (sealed very well in a plastic baggy) in the freezer overnight and then quickly putting it in an external enclosure and getting the data off it that way.
Message was edited by: WZZZ

Flashing folder with question mark on screen

flashing folder with question mark on screen

This is the first time I have joined the support forum for MacBook - I tried the after Power Off - then while you turn it back on again your hold the "Command + R" - This has worked for some people - this was obtained on YouTube - see www.youtube.com/watch?v=flv2ebQMMtE. This however, did not work for me. I remember having a problem with my PC a few years ago - when I experienced something like this on it. I fixed it by taking out the battery. I was going to check the cable between the hard drive and the motherboard to make sure it was secure. I removed the Battery on my MacBook - blew it off, and put it back in again and surprisingly it booted up normally. Thanked the Lord for the quick fix. Back to Normal.

Flashing Finder Icon/ Question Mark on Boot

Similar Messages

Maybe you are looking for