FPGA compilation error 1000

Today when I wanted to compile my VI, I got this error and don't know what the reason is and how to solve it. Next, I couldn't find anywhere on the forum / Google a similar case.
Does someone has an idea where it might come from and how to solve it?
An internal software error has occurred. Please contact National Instruments technical support at ni.com/support with the following information:
Error 1000 occurred at an unidentified location
Possible reason(s):
LabVIEW: The VI is not in a state compatible with this operation.
Method Name: <b>Generate VHDL</b>
Solved!
Go to Solution.

Hi Harlequinade.
Can you give me some information.
Wich LV version, OS and wich hadware do you use.
One what you can try: "Before compiling to a bitfile click the combination Ctrl+Shift+Run Arrow in the VI"
Best regards
Bernhard Rennhofer, AE
National Instruments (Germany,Munnich)

Similar Messages

Fpga compilation error

Hi all
I am developing the labview code for my application and I have faced the following problem:
I have a PXI system with 2 fpga cards (7854R and 7851R) for adquiring 13 fast analog signals. I finished the work related to the 7854R and everything was working OK. Now I am working in the 7851R, whose code is much simpler than the one in the 7854R. However, I cannot compile the fpga7851.vi. I got a error, that can be checked in the report attached. This VI can be compiled without problems when it is included in a new empty project, so I assume there is no problem in the VI itself. I have tried to set smaller FIFO and Data Buffers for this FPGA, but cannot compile either.
Could you give some advice to find what is really happening here?
Thanks in advance,
Regards,
Pablo
Attachments:
XilinxLog.txt ‏712 KB

Hi Pablo,
A comparison on numerical data types can be found here.
EDIT: My reply below was written to your post ‎2014-03-07 10:41 AM:
You are correct, it looks like the program you are synthesizing is to large for the FPGA. Could you please verify by deploying a smaller program?
One of the last entries in the error log states that
"ERROR:Map:237 - The design is too large to fit the device. Please check the
Design Summary section to see which resource requirement for your design
exceeds the resources available in the device."
There are some more information about the FPGA in the NI PXI-7851R Data Sheet, I have extracted the most relevant information for you below:
NI 7841R/7851R
FPGA type
Virtex-5 LX30
Number of flip-flops
19,200
Number of 6-input LUTs
19,200
Number of DSP48 slices (25 × 18 multipliers)
32
Embedded block RAM
1,152 kbits
You can always check the different Reports in the Compilation Status window for resource utlization information on your current project.
Best regards,
Robert P-F
Applications Engineer
National Instruments Sweden

Open VI Reference Error 1000

Here is the problem:
I am opening a VI (we will call SubVI) through "Open VI Reference" and running the VI in parallel with the VI (MainVI) that I am opening it from. When I run the MainVI using "Run when Opened", I get a Error 1000 and the SubVI freezes. I break out using ctrl-period. Then I start it up from within LabVIEW and the Error 1000 does not appear. Does anyone have an idea of what is going on? Thanks.

I'm a bit unclear as to what your setup is. I suggest you post an example which will help clear it.
As a guess, error 1000 means "The VI is not in a state compatible with this operation". If the subVI is the one set to be run when opened, maybe calling it dynamically is what causes the problem.
Try to take over the world!

HD movie download problems (error 1000)

I have recently purchased two HD movies (which I have downloaded) and just purchased Guardians of the Galaxy. Every time I try to download it onto my computers it gets to the end and I get an error (error 1000), I can watch it on my apple TV, but it wont download on my macbook pro or iMac. Everything is up to date as far as software goes. I have had the same internet for all the movies I have purchased and never had any problems with HD movies. Any suggestions?

In my professional opinion, you should avoid house blackouts while downloading any kind of data. Keep a generator handy.
Sorry, I have nothing to offer in assistance. This is all uncharted, untried territory. I would hope that ATV would be able to figure out that a partial download had occurred and continue from wherever it needed to for a clean, complete download.
Jim

Why do I keep getting Error 1000 When I run Abort VI Method?

Need to know how to get this to work

Hitman,
Here is a KnowledgeBase that discusses the issue.
Why Do I Get Error 1000 When Attempting to Abort a VI Through VI Server?
Evan
National Instruments

Damaged AIR File, Error #1000

Hello,
This is my first post, but hopefully someone here will be able to help me.
I am a Flex Developer who was just recently assigned to help out on a project that has gone bonkers. The project had been going fairly well... but after the latest build the following messages comes up during installation on Windows XP.
"Sorry, an error has occured.
The application could not be installed because the AIR file is damaged. Try obtaining a new AIR file from the application author."
Awesome! All we need to do is get a new AIR file from the application author... oh wait... I AM the application author. Grumble grumble.
So I tried reinstalling the application, but this time I ran it with .airappinstall.log. Here is what was output by the log.
Starting app install of file:///C:/Documents%20and%20Settings/Administrator/Desktop/2009-11-30r33MW4.air
UI SWF load is complete
UI initialized
Unpackaging to C:\Documents and Settings\Administrator\Local Settings\Temp\fla1D.tmp
failed while unpackaging: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="Error #1000" errorID=1000]
starting cleanup of temporary files
application installer exiting
So, what exactly is this error? Can anyone point me to a place where I might be able to look up what Error #1000 is?
Don't worry I have done my homework, I know there are a decent amount of posts about people recieving an "AIR file damaged" error. I have looked and read through them all, but when they run a log on the install it ends up being a different error...so the other posts are not entirely helpful.
I am guessing something must have been changed in the most recent build but I was just placed into this project so I do not have much knowledge of previous versions. Any hints of suggestions about common things to check that might be causing this would be greatly appreciated.

It might help if you can get the installation log and post
it.
To get the log, create a file .airappinstall.log in your home
directory.

Error 1000 when opening a vi from tools menu

Hi All,
I have created a vi(attached), which creates a new library and adds another vi to it. This vi seems to be working fine when we open and run it from its location on the disk. If I try opening and then running this vi by selecting it from the LabVIEW tools menu (This was done by placing it in the location-National Instruments\LabVIEW 8.6\project ), I get an error 1000 after the property node for 'Name' . Error 1000 states 'The VI is not in a state compatible with this operation'. I would be really glad to know why this happens or even an alternate solution for it.
Thanks in Advance,
Ibrahim.
Attachments:
AddtoLibrary.vi ‏14 KB

If you run it from the tools menu, it is running in a seperate Application Instance called NI.LV.Dialog of LabView. You need to get hold of the Main Application Instance.
Have look at this link:
http://forums.lavag.org/Accessing-VIs-across-contexts-t12950.html&pid=57735
But be warned, that it is located under the rusty nails section and this stuff is not officaially supported by NI or anyone else.
Felix
www.aescusoft.de
My latest community nugget on producer/consumer design
My current blog: A journey through uml

VI Metric.DataSize Property Error 1000 during execution

OK, maybe this will be an easy one for someone. Today I'm attempting to detect an apparent memory leak in a Windows executable on 8.6.1 that, despite my best efforts, is still causing the painfully ambiguous "Not enough memory to complete this operation" dialog to appear.
This is within an executable, so I thought the best way to tackle this would be to read the "Metric.DataSize" property off of suspect VIs during execution. I'm getting error 1000, which leads me to believe that I can't read the property while the VI in question is running. Is there some way around this? Is there an easier way that I've forgotten?
I saw a rather old post of a similar nature relating to 7.1, but the recommendation was to use the memory monitor example. I took a look at that example's code, but they're calling the same property without error handling.
Thanks a lot,
Jim

Hello Marti,
First of all, thanks for getting back to me. I did manage to track down the memory leak -- more on that soon enough -- but here are some answers to your questions:
First, I'd recommend trying to tackle this issue in the original VI. When you run the VI, do you get the same error?
If you're asking whether I see the error in the development environment, I haven't, unfortunately. However, I haven't run the VI for any extended period of time, either. Also, I don't know if I was clear on this: it's not really an error message in the traditional sense of a code and description. It's just a plain dialog that appears to be thrown by the runtime engine.
If not, can you monitor LabVIEW's usage in the Windows Task Manager, and see if it creeps up continuously?
I hadn't resorted to trying that just yet because I was hoping there was an easier (and more specific) way. The dialog I had seen was the plain one that the runtime engine seemed to have launched, so I figured it was a pretty safe bet that it was a memory leak. I could confirm this with task manager, though, if it's helpful.
If it does not, then you may not have a memory leak but be performing operations or copying large data arrays inadvertently. What is your VI doing? Are you ensuring to close all references at the end of your code?
In this case it's a "web viewer" application that receives data from a parent VI via a notifier and displays it for connected browsers. I'm also scanning some status strings and parsing out relevant information. I know it's within the web viewer VI because the parent VI hasn't changed and has run for weeks without any issue. (I only recently added the web viewer) I am downright paranoid about memory! I close every reference every time and even use the "in place" structure every time I can.
Does the VI run for a bit or error out with the memory issue immediately?
It takes a while; usually an hour or two.
Please investigate into the original VI so we can continue troubleshooting. If this is isolated to the executable, it will be a little tougher to debug. Additionally, if you don't have the original VI, you will need to get it either way so that we can investigate the source of this issue.
Okay, as I said earlier, I think I've figured it out. I have a VI that writes to a string indicator by reference. I had a circular buffer for messages (it used the in place structure, too!) and I was updating the string indicator with the buffer contents. I'm almost certain that the circular buffer works properly because I've used it before without any issue. However, I think it had something to do with the manner in which I was updating that string by reference over and over again. I know, it sounds crazy because I've updated indicators by reference continuously before and had never had an issue. It's possible that I was also using my circular buffer in a different way than I was before. I could explain what I did differently to fix the issue, but it would be a couple more paragraphs. (I will if you want!) For the record, I was definitely closing the reference every time, too. In any case, I think the issue is solved, but if you're interested in additional information I'll try my best.
By the way, here's my circular buffer VI.
Again, Marti, thanks very much for your assistance.
Regards,
Jim
Attachments:
Circular Buffer (Strings).vi ‏14 KB

Error 1000: AFx Library library exception: Sql encountered an error: These columns don't currently have unique values.

Hi everyone,
Using the Writer block, configured with a correct SQLAzure instance, I experience this error:
- Error 1000: AFx Library library exception: Sql encountered an error: These columns don't currently have unique values.
I have read that this error can be related to inheritance problems, but my table does not have inheritances of any kind:
CREATE TABLE [dbo].[my_table](
[my_float] [float] NULL
) ON [PRIMARY]
GO
Writer block parameters:
Comma separated list of columns to be saved:
temp (from Bike Rental UCI Dataset)
Data Table name: [dbo].[my_table]
Comma separated list of datatable columns:
[my_float]
The experiment from which I have extracted the writing part was able to correctly write to DB until few days ago. Is it possible that some changes in the platform are causing this issue or am I doing something wrong?
Thank you and best regards,
FV

Hi Maureen,
Yes, the scenario is correct. On SQL profiler I can't see any SQL operation that can lead to that kind of error, but as you were saying it was worth trying anyway having that error message.
New test scenario:
CREATE TABLE [dbo].[my_table_identity](
[ID] [int] IDENTITY(1,1) NOT NULL,
[my_float] [float] NULL,
CONSTRAINT [PK_my_table_identity] PRIMARY KEY CLUSTERED
[ID] ASC
)WITH (PAD_INDEX = OFF, STATISTICS_NORECOMPUTE = OFF, IGNORE_DUP_KEY = OFF, ALLOW_ROW_LOCKS = ON, ALLOW_PAGE_LOCKS = ON)
) ON [PRIMARY]
-- These lines work fine on SQL Management Studio
INSERT INTO [dbo].[my_table_identity] (my_float) VALUES (1.23)
INSERT INTO [dbo].[my_table_identity] (my_float) VALUES (1.23)
INSERT INTO [dbo].[my_table_identity] (my_float) VALUES (1.23)
-- I can see all new rows with each one a different ID
SELECT * FROM [dbo].[my_table_identity]
dbo is the default schema for my Azure login.
New writer block parameters:
Comma separated list of columns to be saved: temp
(from Bike Rental UCI Dataset)
Data Table name: my_table_identity
Comma separated list of datatable columns: my_float
I still get the same error: Error 1000: AFx Library library exception: Sql encountered an error: These columns don't currently have unique values.
I have also tried to pass the "instant" column instead of "temp", as it hasn't any duplicated values, but still no luck.
I attach the log file (purged of sensitive information) because I see some error / warnings there.
https://dl.dropboxusercontent.com/u/40411467/azure_log.txt
Thank you again and best regards,
FV

Stop thread with error 1000

Ｉam trying to start a thread by dynamically calling a re-entry vi and get a calling reference therefore. When I need to close the vi, I just use that vi reference to close it.
But I got the Error 1000 LabVIEW: The VI is not in a state compatible with this operation.
Please see the attached piece code for the way I am open and close it(, since the original code is a bit complex)
P.S.
What is the best way to stop one of the multi dynamically called out re-entry vi outside itself somewhere else.
Also if multi instances of one re-entry vi are called out, how to monitor their existing status in debugging, such as whether they been killed. The log file some time is a bit slow.
Thanks
Solved!
Go to Solution.
Attachments:
Open Close.vi ‏19 KB
PubSub_QueueServiceTask.vi ‏22 KB
PubSub_TCPServiceTask.vi ‏15 KB

Hi,
Even though the subVI that you called is running, it is not running under its own execution; it is part of the execution of the top-level VI. The execution of a VI depends on the execution of the subVI that is called, so you are not allowed to abort the execution of a subVI. Even though two parts of the main VI may be running in parallel (the subVI and the VI Server Abort command), the subVI is not executing on it's own; it is part of the caller VI.
In order to abort a subVI from another VI, it needs to be running as a VI, not as a subVI. To make this happen, you would need to start the subVI through VI Server, using an Invoke node with the Run method. You also need to set the Wait until done option to False to eliminate the data dependencies of this VI. This way you can run and abort a VI from another VI. The major drawback to this however, is the greater difficulty of passing data values to the called VI. You would have to use the Set Control Value and Get Control Value methods to pass data to and from the called VI. I attached the examples below.
Sincerely,
Gunyapart Deephanphongs
Application Engineer
NI ASEAN
Message Edited by Chongnang on 11-21-2008 03:22 AM
Attachments:
That.vi ‏11 KB
This.vi ‏12 KB

Error: 1000: No bitrate match

Does anybody have an answer for this?
Error: 1000: No bitrate match
at mx.controls.videoClasses::VideoPlayer/pause()
at mx.controls::VideoDisplay/pause()
at components::page7/playPause()
at components::page7/__playPauseBtn_click()
Thanks in advance,
Gene

I have found the solution.
Please be aware that these steps do not resolve any issue
with Flash, but are a configuration step for Microsoft Windows 2003
and Microsoft IIS Server 6.0. Any difficulties in executing these
instructions or any errors that may arise from modifying your
system settings should be addressed to Microsoft. For more details,
please refer to your IIS documentation.
On the Windows 2003 server, open the Internet Information
Services Manager.
Expand the Local Computer Server.
Right-click the local computer server and select Properties.
Select the MIME Types tab.
Click New and enter the following information:
Associated Extension box: .FLV
MIME Type box:flv-application/octet-stream
Click OK.
Restart the World Wide Web Publishing service.

App World purchase error 1000

I try to buy a game (Bejewel) and after I pay for it said that the purchase is not found.
This purchase went thru my credit car 5 times and I can't get the game or my money back.
I got a message at the end that said that was an error 1000.
Please if some one know about it and can help me.

I have this problem as well. i try to buy themes and after i pay for it it appear error 1000 but this purchase went thru my credit card 3 times from 2 diff card. i still can't get the themes or refund.

Indesign CS6 start niet op op Dell optiplex (javascript.rpln error 1000)

Wij rollen voor het onderwijs CS6 Webpremium uit.
Nu start deze netjes op alle HP pc's die we hier hebben staan, maar op de Dell pc's loopt alleen Indesign CS6 vast bij starten met een Javascript.rpln error 1000.
De pc's zijn met een identiek image uitgerold, ook onder een admin account start het pakket niet.
Ook lijken de Dell optiplex 755 pc's te voldoen aan de minimale systeemeisen.
Mocht iemand een tip of oplossing hebben .....

VideoDisplay rtmp stream - error 1000 on replay

Hi,
I am unable to restart my video after it plays once all the way through. I keep getting error
error: 1000: Unable to make connection to server or to find FLV on server.
when I call videoDisplay.play() after the video is done playing. Obviously it can find becasue it found it the first time through, Could this be due to the fact its an rtmp stream? what else could be the issue?
thanks in advance...
<mx:Canvas id="myCanvas" visible="true" rollOver="showControls()" rollOut="hideControls()">
        <mx:VideoDisplay   rewind="onRewind(event)" visible="false" ready="onVideoReady(event)" id="videoDisplay" source="rtmp://myserver.com/flash/Desertrace.f4v" autoPlay="true" playheadUpdate="videoDisplay_playheadUpdate(event)" />
        <mx:HBox visible="false" id="controls" styleName="controllerStyle" alpha="0.0">
            <mx:Button id="playPauseButton" styleName="playPauseStyle" toggle="true" selected="{videoDisplay.playing}" click="playPauseButton_click(event)" />
            <mx:Button id="stopButton" styleName="stopStyle" click="stopButton_click(event)" />
            <mx:Spacer width="100%" />
            <mx:Label id="time" styleName="timeStyle" />
        </mx:HBox>
         <mx:ProgressBar id="myProgress" indeterminate="true" minimum="0" maximum="100" label="Loading Movie..." fontSize="12" fontFamily="Arial" fontWeight="bold" color="#080808">
       </mx:ProgressBar>
    </mx:Canvas>

You will get a better luck if you post this question on media server forum:
http://forums.adobe.com/community/adobe_media_server?view=discussions

Hp camera error 1000

I have received a solution for the camera 1000 error- to reset to factory settings, but it keeps recurring and sometimes the solution just do not work. I cannot copy and scan when this happens.
What could be the reason for that error message? Is there a permanent solution?
Thanks

Hello melhoo,
I understand you're receiving the same error message "Camera error 1000" again. It seems like you have performed all the necessary steps from previous posts.
I would make sure this printer is plugged into a direct wall, not a surge protector. I just want to see if this makes a difference. If not, please contact HP technical support for further assistance. Click here to find out: HP Worldwide Contact.
Good luck.
I worked on behalf of HP.

FPGA compilatio​n error 1000

Similar Messages

Maybe you are looking for

FPGA compilation error 1000