Fsck fails with bad inode number 0 to ginode

Hi,
I'm trying to repair a ufs filesystem on Solaris 10 but it keeps failing with the message:
bad inode number 0 to ginode
Does anyone know how to get around this issue?
Thanks,
Ted

I had this identical failure and the only solution I found anywhere was to format the drive, but I tried an alternate strategy which worked..
The inode failure repeated during Phase 3 of fsck. I answered NO, to the Reconnect prompts during that Phase, and answered Yes to the Phase 4 & 5 prompts. After serveral fsck runs, Phase 4 & 5 errors were all fixed. On the next run of fsck, Phase 3 also passed - the bad inode error was gone.
I could then mount the drive READ/WRITE and restore a corrupted library file. The server then booted up clean.
The fix took less than 30 minutes...much better than the nuclear option!

Similar Messages

Ifconfig pcelx0 plumb fails with Bad file number error

Hi,
I installed solaris 8 (x86) on a Toshiba Tecra 8000.
The Tecra uses Neomagic NM2200 chipset for it's display.
Even though it is not supported by the Sun Drivers, getting xfree86 for sun fixed the display problem for me.
Now according to the various sources that guided me in this task seemed to point at a few things that I had to do in order to make the Tecra work okay with Solaris 8 :
1)Change the PCMCIA mode in the BIOS from automatic to PCIC mode
2)Make sure that there were no IRQ conflicts on the system.
3)Install the OS.
Once the OS was installed, I ran prtconf -D and saw that the network instance #0 pcelx0 was showing up under pcic.
I did not have to install the xig init-pcic patch.
But it did not create an entry in /devices or /dev (as a link) with the error
"pcelx0 requested IRQ failed 6".
Also, I suppose that is the reason why when pcelx0 is plumbed, it comes out with the error message:
ifconfig pcelx0 plumb : "bad file number"
Any help will be greatly appreciated.
Thanks,
Dwai.

Thanks Alex,
I found out -
ifconfig adapter plumb will fail with Bad File number error when the device file that is being referred to is missing.
I checked and found that the pcelx link is not being made in the /dev directory and the file not created in /devices.
I also found that when /reconfigure is run, it tries to create the device for pcelx but fails with this eror message:
pcelx : RequestIRQ fail 6
I am assuming that there is some IRQ conflict with some other device.
Thanks,
Dwai.

Solaris boot images fail with bad magic number

hi guys, have had Solaris on boxes for allmost 10 years. I have never installed sol10, and I have a problem
1. I download the zip file, then use winrar to unzip them..
2. burt the image with nero 7
when my SunBlade 1000 comes up I do the Stop-A, and from the Ok promt
I do boot cdrom
this fails with "bad magic number" I have redown loaded it and reburnt it with nero reinstalled
and also changed out the DVD on SunBlade
3 I found a copy of Solaris 8 and the I got back a 'bitch' where is Solaris 9 so, most likely the drive is OK
HELP
Cris Harrison

Hello Cris,
unfortunately I don't understand your last sentence !
I found a copy of Solaris 8 and the I got back a '*****' where is Solaris 9 so, most likely the drive is OK
If this was a Solaris 8 (7/01 or later) DVD that did successfully boot, your DVD drive firmware (assuming that this is the Sun Toshiba SD-M1401) is up-to-date. If the DVD drive has firmware 1007, an update to 1009 is required to boot from DVD. otherwise you won't be able to boot from DVD (boot from CD works and a DVD can be automounted/mounted).
Partial output of probe-scsi
Before update:
Unit 0 Removable Read Only device TOSHIBA DVD-ROM SD-M14011007
After update:
Unit 0 Removable Read Only device TOSHIBA DVD-ROM SD-M14011009
[*Patch 111649-04 - Toshiba DVD 1401 firmware update*|http://sunsolve.sun.com/search/advsearch.do?collection=PATCH&type=collections&queryKey5=111649&toDocument=yes]
when my SunBlade 1000 comes up I do the Stop-A, and from the Ok promt ...
Instead of trying to directly boot, disable auto-boot and retry after a clean power-on.
Break with Stop-A
setenv auto-boot? false
reset-all
boot cdrom
Michael

Create project from template failed with "badly formed pathname" error message

Hi,
I am trying to create a project from a custom template, but I am getting the following error message prompt:
LabWindows/CVI could not create
Test_Project
because of an error: Badly formed pathname
However, when I checked the target project directory, I see the project files are copied correctly. I don't know if there is something missing from our custom templates? Of, if there is something wrong with our custom template?
I am using LabWindows/9.0
Thank you.
Peggy

Hi Peggy,
Did I understand you correctly that the files for the new project appear to have been created, but the error dialog still shows? In addition to Wolfgang's suggestions, take a look at the help section on New Project and File Templates. This describes everything that should be needed to create a custom template. Also, try to create a new, very basic custom template and make sure that you can use it successfully. If you can, start adding in the functionality of the original template, and test along the way. Hopefully either this new one will work once you finish, or you will see at which point it is breaking, and we can debug from there.
Best Regards,
John M
National Instruments
Applications Engineer

Jdbc insert fails with 01722: invalid number but sqlplus doesn't

I am experiencing a 01722: invalid number on a remote system in Canada. Initially, I couldn't insert '0.0' into a number field, but after changing the ...Oracle/HOME0 ... registry value from ENGLISH_CANADA.WE8MSWIN1252 to AMERICAN_AMERICA.WE8MSWIN1252 and recycling the App Server (Oracle client) I was able to insert '0.0' into a number field.
But my java app using JDBC had the same error "ORA-01722: invalid number" occurring for the same table and attribute -- only this time -- when I attempted to manually insert the same insert '0.0' into a number field -- it worked via SQLPlus.
The NLS_Lang is set to AMERICAN_AMERICA.WE8MSWIN1252.
I confirmed that the HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Nls\CodePage\ACP value is 1252.
Assuming a theory that maybe it is a setting on the DB Server, I tried reproducing this problem locally in my lab configuration by setting the NLS_Lang registry value to ENGLISH_CANADA.WE8MSWIN1252. I used the same jdbc test app to issue the insert....but it worked.
--- Any advice on what other configuration changes could influence the number data type or whether it is possibly a DB Server setting instead of client -- would be greatly appreciated.

JDBC does not care about NLS_LANG. It takes the Java default locale, maps it to Oracle language/territory pair and sends to the server.
Just try this:
Statement stmt = conn.createStatement();
stmt.execute( "ALTER SESSION SET NLS_NUMERIC_CHARACTERS='.,'" );
or bind numeric datatypes.
-- Sergiusz

Outbound mails fails with error message number 826,Cannot process message,

Hi
We are in process of configuring outbound mail.
Profile parmeteres adapted are icm/server_port_0= PROT=SMTP,PORT=0,
is/SMTP/virt_host_0=:;and followed the notes 421359 for ICM Parameters
when we give the SMTP port number as 25,SMTP serveice in SMIC is not working and when we changed to 0 SMTP service is working.
Now the issue coming is we are not able to send the Mails to any domains and the error message in SOST is
*message number 826,Cannot process message, no route from XXXXX to XXXXX.com.*
Please suggest on how to over come the issue,are we missing any parameters or any other configurations.
All your help is highly Appreciated.
Regards
Swetha

HI
Did you check in SCOT?
SCOT>SMTP->Internet
SCOT>Settings-->Default Domain.
Please also check if you can telnet the SMTP server.
Anindya
Edited by: Anindya Bose on Mar 3, 2010 5:13 PM

We have an Iplanet 4.1 in front of an app server; request of the form .../?option=� fail with "Bad Request" if they contain a Spanish character... how can this be avoided?.

If we issue the request to the app server directly it does not fail; the web server is intercepting the request.

Hi,
Are you running iWS 4.x(SP3-SP5) version of iWS. If so the iWS 4.x strictly enforces US-ASCII requirements of the HTTP RFC and does not allow non-ascii characters in the field of a HTTP header.
There is a temporary workaround to relax the restriction on HTTP headers to non ASCII characters, Please add the following line to your web server magnus.conf file:
StrictHttpHeaders off
Please make sure that after changeing the values in magnus.conf file you restarted the iWS, for new changes take effect. The above workaround will work otherwise, you would need to write your own NSAPI code to scrub the HTTP headers for any non
US-ascii characters.
Hope this helps.
Regards,
Dakshin.
Developer Technical Support
Sun Microsystems
http://www.sun.com/developers/support.

OCFSV2 : mount.ocfs2: Bad magic number in inode

Hi everyone,
DUe to high load I/O, i can't mount my ocfsV2 partition :
mount.ocfs2: Bad magic number in inode while trying to determine heartbeat information
marge:~# fsck.ocfs2 /dev/sdc1
fsck.ocfs2: Bad magic number in inode while initializing the DLM
The disk is an iscsi device, there are no block damaged.
I try to modify the signature with bvi but the result is the same.
The disk containt image file created with dd (Virtual machine).
Do you have a software or a workaround to recover my vm's ?
Or i must consider to format my parttion ?
Thank you

I know , i wan't to switch to Linux forum but how to do that ? :-)
marge:~# modinfo ocfs2
filename: /lib/modules/2.6.26-2-xen-amd64/kernel/fs/ocfs2/ocfs2.ko
license: GPL
author: Oracle
version: 1.5.0
description: OCFS2 1.5.0
srcversion: C692B48692BFC8597E4D7A7
depends: jbd,ocfs2_stackglue,ocfs2_nodemanager
vermagic: 2.6.26-2-xen-amd64 SMP mod_unload modversions Xen
I created the filesystem with debian :
mkfs.ocfs2 /dev/sdc1
By default it create 4K cluster size. And it make 6 backup off superblock.
But recover superblock doesn"t work :
marge:~# fsck.ocfs2 -r 1 /dev/sdc1
[RECOVER_BACKUP_SUPERBLOCK] Recover superblock information from backup block#262144? <n> y
fsck.ocfs2: Bad magic number in inode while initializing the DLM
marge:~# debugfs.ocfs2 -R stats /dev/sdc1
     Revision: 0.90
     Mount Count: 0 Max Mount Count: 20
     State: 0 Errors: 0
     Check Interval: 0 Last Check: Thu May 7 16:26:37 2009
     Creator OS: 0
     Feature Compat: 1 BackupSuper
     Feature Incompat: 16 Sparse
     Tunefs Incomplete: 0 None
     Feature RO compat: 1 Unwritten
     Root Blknum: 5 System Dir Blknum: 6
     First Cluster Group Blknum: 3
     Block Size Bits: 12 Cluster Size Bits: 12
     Max Node Slots: 4
     Label:
     UUID: 3677066B5C7B424BB79FE30764552B57
     Cluster stack: classic o2cb
     Inode: 2 Mode: 00 Generation: 3020404948 (0xb407b8d4)
     FS Generation: 3020404948 (0xb407b8d4)
     Type: Unknown Attr: 0x0 Flags: Valid System Superblock
     User: 0 (root) Group: 0 (root) Size: 0
     Links: 0 Clusters: 52432135
     ctime: 0x4a02ef9d -- Thu May 7 16:26:37 2009
     atime: 0x0 -- Thu Jan 1 01:00:00 1970
     mtime: 0x4a02ef9d -- Thu May 7 16:26:37 2009
     dtime: 0x0 -- Thu Jan 1 01:00:00 1970
     ctime_nsec: 0x00000000 -- 0
     atime_nsec: 0x00000000 -- 0
     mtime_nsec: 0x00000000 -- 0
     Last Extblk: 0
     Sub Alloc Slot: Global Sub Alloc Bit: 65535
debugs say superblock is ok but unable to mount the partition :
mount.ocfs2: Bad magic number in inode while trying to determine heartbeat information

Export for system copy fails - Error 9 (Bad file number)

Hello all,
I am attempting to perform the export phase for a hetergenous system copy on our BI system (BI 7.0 - NW2004s). This system runs on HP-UX 11.11 using Oracle 10.2.0.2 and will be migrated to Windows Server 2003 and MS SQL Server 2005, once the export is complete.
While running sapinst to export the data from the source system, there are several input dialog screens that are skipped, which means I am not able to enter all the paramters used for the export. After seeing this behavior from sapinst, I reviewed the sapinst.log and sapinst_dev.log files and find the warning/error "System call failed. Error 9 (Bad file number)". I have included a portion of these files below.
I have reviewed notes 546006 and 583861, but these seem to refer to an Oracle error ORA-27121, but I am not receiving any Oracle errors in sapinst.log or the Oracle alert log. I have looked for possible permission or ownership problems with any of the SAP or Oracle files, but have not found any that were incorrect. Also, these errors do not specify which file sapinst is having problems with, so I do not have a specific file or area to check.
If anyone has seen something similar to this and has any suggestions, I would greatly appreciate any help.
sapinst.log details:
INFO 2009-02-14 15:15:51.67
Execute step collect of component |NW_Export|ind|ind|ind|ind|0|0|NW_GetSidFromProfiles|ind|ind|ind|ind|1|0|NW_readProfileDir|ind|ind
|ind|ind|0|0
INFO 2009-02-14 15:15:52.737
Account bwpadm already exists.
WARNING 2009-02-14 15:15:52.747
System call failed. Error 9 (Bad file number) in execution of system call 'getgrent' with parameter (), line (292) in file (syuxcuse
r.cpp).
INFO 2009-02-14 15:15:52.757
Account 0 already exists.
WARNING 2009-02-14 15:15:52.777
System call failed. Error 9 (Bad file number) in execution of system call 'getgrent' with parameter (), line (292) in file (syuxcuse
r.cpp).
INFO 2009-02-14 15:15:52.777
Account 200 already exists.
WARNING 2009-02-14 15:15:52.827
System call failed. Error 9 (Bad file number) in execution of system call 'getgrent' with parameter (), line (292) in file (syuxcuse
r.cpp).
INFO 2009-02-14 15:16:04.937
Creating file /tmp/sapinst_instdir/NW04S/LM/COPY/ORA/EXP/CENTRAL/AS/EXP/ypcat.log.
INFO 2009-02-14 15:16:05.007
Output of ypcat passwd.byname is written to the logfile ypcat.log.
sapinst_dev.log details:
TRACE      2009-02-14 15:15:52.737
2009-02-14 15:15:52.743 NW._getSAPMount() done: /sapmnt
INFO       2009-02-14 15:15:52.737 [syuxcaccmg.cpp:227]
           bool CSyAccountMgtImpl::isExisting(ISyAccountMgt::eAccountType accountType, iastring sName)
Account bwpadm already exists.
TRACE      2009-02-14 15:15:52.747 [syuxcuser.cpp:1943]
           CSyUserImpl_getOsInfos(ILogBook *m_logBook, iastring sName, iastring sID, tSyUserInfo& msUserinfo)
getspnam(bwpadm) returned NULL.
WARNING    2009-02-14 15:15:52.747 [syxxsyshlp.cpp:78]
           syslib::printOSError(const iastring &, int, DWORD, const iastring &, CMessage::eLogMessage)
System call failed. Error 9 (Bad file number) in execution of system call 'getgrent' with parameter (), line (292) in file (syuxcuse
r.cpp).
Regards,
Rusty Robbins

Hello Peter,
Thanks for the reply. I did confirm the points you made, and have the details below.
1. check filesystem, if you have enough space, especially /tmp
All filesystems have available space, and /tmp has 310 MB available, before the start of sapinst.
2. check again alert log, trace log for Oracle,
I could not find any errors in the alert_SID.log or any unusual trace files.
3. How did you run sapinst? Are you using "root" account.
I am running sapinst as user root and I am following all the recomendations in the system copy guide (at least as far as I can tell. ;p )
We have four BI systems in this landscape, and the other three have migrated successfully. The procedure I am using, is the same as for the other 3 systems and uses the same SAP media directory that was used on the other systems.
One other item that may be part of my problem here, is that this system is the production system, and was originally installed as a high-availability system, using HP-UX Service Guard for clustering. Currently, this system does not have fail-over enabled, but of course the cluster is still intact. One required piece of the Service Guard enviornment is the use of a virtual hostname. This seems to resolve successfully by sapinst, as I see the correct (virtual) hostname referenced several times. While this is a clustered system (for fail-over purposes), the CI and DB are installed on the same host. So it is not a distributed system, and if failover had been initiated, it would fail both the CI and DB instance, which is the same and only SAP instance.
This did raise one question in my mind, however. I am attempting to extract this using the following menu path within sapinst.
SAP NetWeaver 7.0 Support Release 3 --> Software Life-Cycle Options --> System Copy --> Oracle --> Source System Export --> Central System --> Based on AS ABAP and AS Java
Since this does use Service Guard, but is not a distributed system, should I be using a different path in the sapinst tree, for the export? I have only performed a migration using the above path, so I am not familar with the detailf of the other types, such as High-Availabitly or Distributed-System.
Regards,
Rusty

Can't print from Adobe Acrobat 11.0.07 on my MAC OS 10.6 to HP PSC 1350. Error: PSTOPDFFILTER/PSTOCUPSRASTER FAILED WITH ERR NUMBER 13. How do I fix it so I can print?

Can't print from Adobe Acrobat 11.0.07 on my MAC OS 10.6 to HP PSC 1350. Error: PSTOPDFFILTER/PSTOCUPSRASTER FAILED WITH ERR NUMBER 13. How do I fix it so I can print?

i am getting the same error, suddenly, on 10.9.5

[Unsolved] Kernel linux 3.8.4-1 fails with fsck boot error on raid 0

The stock linux-3.8.4-1 (x86_64) fails to boot with the following unrecoverable error:
Loading ../initramfs-linix.img......ready.
Probing EDD (edd=off to disable)... ok
early console in decompress_kernel
Decompressing Linux... Parsing ELF... done.
Booting the kernel.
:: running early hook [udev]
:: running hook [udev]
:: Triggering uevents...
Waiting 10 seconds for device /dev/md127 ...
:: performing fsck on '/dev/md127' ...
fsck.ext2: Invalid argument while trying to open /dev/md127
/dev/md127:
The superblock could not be read or does not describe a correct ext2
filesystem. If the device is valid and it really contains an ext2
filesystem (and not swap or ufs or something else), then the superblock
is corrupt, and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>
ERROR: fsck failed on '/dev/md127'
:: mounting '/dev/md127' on real root
mount: you must specify the filesystem type
You are now being dropped into an emergancy shell.
sh. can't access tty; job control turned off
[rootfs /]#
My hooks are:
HOOKS="base udev autodetect modconf block mdadm_udev filesystems keyboard fsck"
I am however able to boot the linux-lts & my own custom kernels. Custom kernel is built from the abs linux package.
The / partition is on a raid 0 with an ext4 filesystem. fsck -f /dev/md127 comes back clean & the raid & two hard drives are healthy.
Last edited by straykat (2013-07-11 09:27:45)

straykat wrote:
xanb,
For sanity to prevail, I am going to suggest the following:
Back up your data
Remove the RAIDs from your 2 linux hard drives. The Arch RAID wiki has instructions on this or (my prefered method) wipe your two linux drives with dd. If you are not sure on dd "Parted Magic" has a GUI for it.
Create a new partition table on both of your linux hard drives.
Partition your 2 linux hard drives as follows;
/dev/sdb1 as / (root) with ext4 fs
/dev/sdb2 as swap
/dev/sdc1 as /home with ext4 fs.
Reinstall Arch Linux on / (/dev/sdb1)
I would also recommend reading up in the Arch wiki, Kernel wiki etc on RAID & decide why you would use it on your system & which one would give you any benefit with your current hardware set up. Also learn more on how to create & maintain a RAID on an Arch system.
Keep in mind that KISS is always the way to go with any computer system as complexity will always increase the amount of mistakes & gotchas.
No. I don't want to behave as ostrich, hide the head ;-) This is my configuration, this is want I want. If archlinux fails, we have a bug. Another question is if the triage of the bug is difficult. No all bugs are good for triagging, but it's real life. If always we change the configuration, we will never detect new bugs.
Keep in mind that I don't want to blame, it's always "good force" comments.
Regards,
Xan.

Java Applet in a HTML page: failing with PLS-00306: wrong number of args

We are trying to use a Java Applet in a HTML page. as our system needs to be able to retrieve a predefined set of data from a third party system that uses Dynamic Data Exchange Protocol (DDE) and are encountering errors from APEX and in IE itself.
We are using JavaDde from www.nevaobject.com that enables our Java applet to interact with Windows applications (Third Party System) using DDE.
This functionality is currently used in our Web Form 6i application and we are trying to use the same in the new ApEx application.
We are using ApEx version : 2.1 and actually aer encountering 2 problems:
Problem 1: ApEx failing with PLS-00306: wrong number or types of arguments in call to 'ACCEPT'
Problem 2: IE crashes if Applet used in a complex page with several regions (1 Context, 4 Report Regions, 2 level Tabs, Links)
This problem does not occur in the page where there is only applet and one region. In the case of complex page the IE crashes if the page is reloaded
Test scenario:
1- Create a simple page with the HTML region.
2- Define the Source of the above region as follows
<OBJECT CLASSID="clsid:8AD9C840-044E-11D1-B3E9-00805F499D93"
CODEBASE="http://java.sun.com/products/plugin/autodl/jinstall-1_4-windows-i586.cab#version=1,4,0,0"
WIDTH="1"
HEIGHT="1"
ID="simpleApplet"
NAME="simpleApplet">
<PARAM NAME="code" VALUE="simpleApplet.class" >
<PARAM NAME="archive" VALUE="simpleApplet.jar" />
<PARAM NAME="type" VALUE="application/x-java-applet;version=1.4">
</OBJECT>
3- Create a simple Java applet "simpleApplet" - for the test its enough if the applet will have just the init method printing out the mesage to the console
4- Create a Submit Button (not redirect) in Region Header and create unconditional (do not set When Button Pressed property) Page Branch to navigate to another page (the page without the applet)
6- Run the page and Submit -
The error below is returned by the engine:
In our case our applet is called ddeApplet - I do not know why is ApEx passing the Applet's ID down to the wwv_flow.accept method as a parameter
Tue, 24 Jul 2007 08:15:39 GMT
ORA-06550: line 7, column 2:
PLS-00306: wrong number or types of arguments in call to 'ACCEPT'
ORA-06550: line 7, column 2:
PL/SQL: Statement ignored
DAD name: rbdev2_ax
PROCEDURE : wwv_flow.accept
URL : http://castor:7778/pls/rbdev2_ax/wwv_flow.accept
PARAMETERS :
============
P_FLOW_ID:
147
P_FLOW_STEP_ID:
500
P_INSTANCE:
6986070096861669560
P_PAGE_SUBMISSION_ID:
1005758
P_REQUEST:
CRASH
P_ARG_NAMES:
100380029717786501
P_T01:
147
P_T02:
101
P_T03:
5000044
P_T04:
1
P_T05:
S
DDEAPPLET:
Ddeapplet[panel0,0,0,1x1,layout=java.awt.BorderLayout,rootPane=javax.swing.JRootPane[,0,0,1x1,layout=javax.swing.JRootPane$RootLayout,alignmentX=null,alignmentY=null,border=,flags=385,maximumSize=,minimumSize=,preferredSize=],rootPaneCheckingEnabled=true]
P_MD5_CHECKSUM:
ENVIRONMENT:
============
PLSQL_GATEWAY=WebDb
GATEWAY_IVERSION=2
SERVER_SOFTWARE=Oracle HTTP Server Powered by Apache/1.3.19 (Unix) mod_fastcgi/2.2.10 mod_perl/1.25 mod_oprocmgr/1.0
GATEWAY_INTERFACE=CGI/1.1
SERVER_PORT=7778
SERVER_NAME=castor
REQUEST_METHOD=POST
QUERY_STRING=
PATH_INFO=/pls/rbdev2_ax/wwv_flow.accept
SCRIPT_NAME=/pls
REMOTE_HOST=
REMOTE_ADDR=192.168.66.169
SERVER_PROTOCOL=HTTP/1.1
REQUEST_PROTOCOL=HTTP
REMOTE_USER=
HTTP_CONTENT_LENGTH=661
HTTP_CONTENT_TYPE=application/x-www-form-urlencoded
HTTP_USER_AGENT=Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.0)
HTTP_HOST=castor:7778
HTTP_ACCEPT=image/gif, image/x-xbitmap, image/jpeg, image/pjpeg, application/vnd.ms-powerpoint, application/vnd.ms-excel, application/msword, application/x-shockwave-flash, */*
HTTP_ACCEPT_ENCODING=gzip, deflate
HTTP_ACCEPT_LANGUAGE=en-us
HTTP_ACCEPT_CHARSET=
HTTP_COOKIE=ISCOOKIE=true; LOGIN_USERNAME_COOKIE=rdanko; ORACLE_PLATFORM_REMEMBER_UN=RDANKO:ngrb; WWV_FLOW_USER2=70FBB00945FE46B9; V6_AUTHENTICATION_COOKIE=70FBB00945FE46B9
Authorization=
HTTP_IF_MODIFIED_SINCE=
HTTP_REFERER=http://castor:7778/pls/rbdev2_ax/f?p=147:500:6986070096861669560:::::
HTTP_SOAPACTION=

"theArrow",
It looks like whatever HTML you're including on your page is creating HTML input form elements inside the HTML form "wwv_flow". This form is posted to wwv_flow.accept, and of course, the PL/SQL procedure wwv_flow.accept doesn't know anything these additional arguments/form elements you're attempting to POST.
Joel

Mac Acrobat Pro 9.3 can't print : pstopdffilter/pstocupsraster failed with err number 13

Summary
Can't print PDF files from Adobe Acrobat Pro 9.3.0 on Mac OS X Snow Leopard (10.6.2) to Brother MFC-7820N Printer (connected via USB). Print queue consistently shows "pstopdffilter/pstocupsraster failed with err number 13".
Steps to reproduce
Launch Acrobat Pro 9.3.0 on Mac OS X Snow Leopard 10.6.2
Open SimpleOnePageDocument.pdf (attached)
From File menu select Print
From Print Dialog select Brother MFC-7820N printer
Click Print Button
Results
Printing immediately fails. Print queue shows "pstopdffilter/pstocupsraster failed with err number 13" (see attached picture)
Expected Results
Document prints
Things I have tried
Downloading latest drivers from Brother for Snow Leopard (fall 2009 drivers)
System Preferences->Print and Fax->Reset Printing Subsystem
Print->Advanced->Postscript Options->Font and Resource Policy - Greyed out so I could not change from Send by Range to Send for each page
Notes
I can print PDF files from the Preview application without any problems.
System Info
Operating System
Mac OS X Snow Leopard 10.6.2
Product
Adobe Acrobat Pro 9.3.0 (installed as part of CS4)
Printer
Brother MFC-7820N connected via USB
Printer Driver
Brother MFC-7820N CUPS version 1.41

I have exactly the same problem since I changed my Mac for an Intel one (10.6.2 instead of Power PC 10.4).
My printer is a Canon MP610 but this has nothing to do with the printer and it's software. Adobe seems to be completely deaf to this issue which is very annoying as most of the downloaded documents you need to print are pdf nowadays.
I surrounded the issue by copying/pasting the pdf image in a jpeg file... This is very time consuming and I'm still waiting for a proper answer to this bug by Adobe.
Let's continue to write, hoping Adobe will begin to move on the subject...

"The request failed with HTTP Status 400: Bad Request." when running reports

Hi,
I installed reporting services and the install went fine.  The Reporting Services are located on a different server. I can see all the reports in SCCM but when I try to run them I get the "400" error with the following details:
System.Net.WebException
The request failed with HTTP status 400: Bad Request.
Stack Trace:
   at System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall)
   at System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters)
   at Microsoft.Reporting.WinForms.Internal.Soap.ReportingServices2005.Execution.ReportExecutionService.LoadReport2(String Report, String HistoryID)
   at Microsoft.Reporting.WinForms.Internal.Soap.ReportingServices2005.Execution.RSExecutionConnection.<>c__DisplayClass2.<LoadReport>b__0()
   at Microsoft.Reporting.WinForms.Internal.Soap.ReportingServices2005.Execution.RSExecutionConnection.ProxyMethodInvocation.Execute[TReturn](RSExecutionConnection connection, ProxyMethod`1 initialMethod, ProxyMethod`1 retryMethod)
   at Microsoft.Reporting.WinForms.Internal.Soap.ReportingServices2005.Execution.RSExecutionConnection.LoadReport(String Report, String HistoryID)
   at Microsoft.Reporting.WinForms.ServerReport.EnsureExecutionSession()
   at Microsoft.Reporting.WinForms.ServerReport.SetParameters(IEnumerable`1 parameters)
   at Microsoft.ConfigurationManagement.AdminConsole.SrsReporting.ReportViewerWindowsForms.SetParameterValues_DoWork(Object sender, DoWorkEventArgs e)
I can open the URL from the SCCM server but when I select a report I am unable to select any report options if available. If no options are availble the report just doesn't run, I don't get and error if I select "View Report" mutiple
times.
If I connect to the Reporting Services site on the computer where it is installed all the reports run fine.
One thing I have noticed is that when I try to change or add a role assignment for Reporting Services the edited account always reverts back to the default settings and the added Domain user is dropped.
Thanks

I reviewed the topic and found a couple of steps I missed the first time around. I had to "Configure Reports to Use Report Builder 3.0 and setting the "Log on Locally" permission.
I then uninstalled the role and reinstalled it. I am still getting the 400 error.
When I inspected the SmsAdminUI.log I noticed the Error on the last line 2151811598 (it repeats in the log). I couldn't find anything specific related to it. By reading a few "related" Internet posts I came accross a intial setup
blog that noted some WMI firewall execptions (Async-in, DCOM-in and WMI-in) as require so I checked and they were not allowed on the SCCM server so I allowed them and tested with the same result. I turned them off again.
Here is the tail end of the SmsAdminUI.log
[19, PID:2684][01/24/2013 16:08:29] :[ReportProxy] - User-specified default Reporting Point [INC-SQL42.deccoinc.net] could not be found, [] is now the default Reporting Point.
[4, PID:2684][01/24/2013 16:08:30] :[ReportProxy] - User-specified default Reporting Point [INC-SQL42.deccoinc.net] could not be found, [] is now the default Reporting Point.
[15, PID:2684][01/24/2013 16:08:30] :[ReportProxy] - User-specified default Reporting Point [INC-SQL42.deccoinc.net] could not be found, [] is now the default Reporting Point.
[1, PID:2684][01/24/2013 19:06:02] :System.Management.ManagementException\r\nNot found \r\n   at System.Management.ManagementException.ThrowWithExtendedInfo(ManagementStatus errorCode)
   at System.Management.ManagementObject.Initialize(Boolean getObject)
   at System.Management.ManagementBaseObject.get_wbemObject()
   at System.Management.PropertyData.RefreshPropertyInfo()
   at System.Management.PropertyDataCollection.get_Item(String propertyName)
   at System.Management.ManagementBaseObject.GetPropertyValue(String propertyName)
   at System.Management.ManagementBaseObject.get_Item(String propertyName)
   at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlConnectionManager.GetInstance(String objectPath)\r\nManagementException details:
instance of SMS_ExtendedStatus
Description = "Error retrieving object FileType=2";
ErrorCode = 2151811598;
File = "e:\\nts_sccm_release\\sms\\siteserver\\sdk_provider\\smsprov\\SspInterface.h";
Line = 1208;
Operation = "GetObject";
ParameterInfo = "SMS_SCI_SysResUse.FileType=2,ItemName=\"[\\\"Display=\\\\\\\\INC-SQL42.deccoinc.net\\\\\\\"]MSWNET:[\\\"SMS_SITE=INC\\\"]\\\\\\\\INC-SQL42.deccoinc.net\\\\,SMS SRS Reporting Point\",ItemType=\"System Resource Usage\",SiteCode=\"INC\"";
ProviderName = "ExtnProv";
StatusCode = 2147749890;
\r\n
[1, PID:2684][01/24/2013 23:39:14] :System.NullReferenceException\r\nObject reference not set to an instance of an object.\r\n   at Microsoft.ConfigurationManagement.AdminConsole.SmsCustomDialog.get_LocaleIndependentIdentifier()
   at Microsoft.ConfigurationManagement.AdminConsole.ShowDialogTaskHandler.DoTask(NavigationModelNodeBase node, SccmTaskConfiguration sccmTask, PropertyDataUpdated dataUpdatedDelegate, Boolean readOnly)\r\n
[1, PID:5008][01/25/2013 20:48:00] :System.Management.ManagementException\r\nNot found \r\n   at System.Management.ManagementException.ThrowWithExtendedInfo(ManagementStatus errorCode)
   at System.Management.ManagementObject.Initialize(Boolean getObject)
   at System.Management.ManagementBaseObject.get_wbemObject()
   at System.Management.PropertyData.RefreshPropertyInfo()
   at System.Management.PropertyDataCollection.get_Item(String propertyName)
   at System.Management.ManagementBaseObject.GetPropertyValue(String propertyName)
   at System.Management.ManagementBaseObject.get_Item(String propertyName)
   at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlConnectionManager.GetInstance(String objectPath)\r\nManagementException details:
instance of SMS_ExtendedStatus
Description = "Error retrieving object FileType=2";
ErrorCode = 2151811598;
File = "e:\\nts_sccm_release\\sms\\siteserver\\sdk_provider\\smsprov\\SspInterface.h";
Line = 1208;
Operation = "GetObject";
ParameterInfo = "SMS_SCI_SysResUse.FileType=2,ItemName=\"[\\\"Display=\\\\\\\\INC-SQL42.deccoinc.net\\\\\\\"]MSWNET:[\\\"SMS_SITE=INC\\\"]\\\\\\\\INC-SQL42.deccoinc.net\\\\,SMS SRS Reporting Point\",ItemType=\"System Resource Usage\",SiteCode=\"INC\"";
ProviderName = "ExtnProv";
StatusCode = 2147749890;
\r\n

JVM issue with applet - Duplicate Key in Parameter Table - Bad Magic Number

Hey, I have Googled this one to death and have seen a few vague references to this problem, but nothing I can relate back as solution.
I wonder if I need to tell the customer to reinstall the OS and, ultimately, the JRE. I'm just looking for a little guidance on what any of you may think. Am I missing a setting or something?
The user is trying to download an applet with IE with 1.3.1_16 and Firefox 1.07 with the Java Embeded Plug-in.
Even though JRE 1.3.1_16, 1.4.2_09 and 1.5 are all installed and Firefox has the JEP also installed, Firefox still wants to use 1.3.1_16 as does IE. I'm guessing that the JEP didn't work.
They can't use Safari which does seem to be using 1.4.2_09 because their RSA ID won't authenticate through it.
On my machine, when I run with the same OS,browsers, and Java 2 plug-ins, I can successfully load the applet.
This is the error that the user gets in the java console is:
Duplicate key in parameter table: code using the htmlAttribute.
first: com.ibm.eNetwork.HOD.HostOnDemand
second: com.ibm.eNetwork.HOD.HostOnDemand.class
java.lang.ClassFormatError: com/ibm/eNetwork/HOD/HostOnDemand (Bad magic number) at java.lang.ClassLoader.defineClass0(NativeMethod)
at java.lang.ClassLoader.defineClass(ClassLoader.java:488)...
Would you reinstall the OS and Java? or look at another setting? or look at the JEP installation again?
Thank you.

Without reading the full post (sorry for that) my guess is that the applet needed to be fetched through a
proxy, the proxy corrupts the applet because it's signed (finjan is one that does that).
The reason why a proxy would do so is because the default settings of sun jre will ask the user the
"do you trust" question to the user which could result in the user loading an applet that is allowed to do
anything the programmer wants (4us, spyware, nasty stuff).
Try to do the following:
1. create a html file locally with the following content:
rightclick and save target as
2. open the page, right click the link and save the file
3. apen the file with an unzip programm (winzip) and check if the content has changed.
4. If the content has changed than the proxy might have done this, contact the system administrator
It might allso have been done by a firewall installed locally.

Fsck fails with bad inode number 0 to ginode

Similar Messages

Maybe you are looking for