Ifconfig pcelx0 plumb fails with Bad file number error

Hi,
I installed solaris 8 (x86) on a Toshiba Tecra 8000.
The Tecra uses Neomagic NM2200 chipset for it's display.
Even though it is not supported by the Sun Drivers, getting xfree86 for sun fixed the display problem for me.
Now according to the various sources that guided me in this task seemed to point at a few things that I had to do in order to make the Tecra work okay with Solaris 8 :
1)Change the PCMCIA mode in the BIOS from automatic to PCIC mode
2)Make sure that there were no IRQ conflicts on the system.
3)Install the OS.
Once the OS was installed, I ran prtconf -D and saw that the network instance #0 pcelx0 was showing up under pcic.
I did not have to install the xig init-pcic patch.
But it did not create an entry in /devices or /dev (as a link) with the error
"pcelx0 requested IRQ failed 6".
Also, I suppose that is the reason why when pcelx0 is plumbed, it comes out with the error message:
ifconfig pcelx0 plumb : "bad file number"
Any help will be greatly appreciated.
Thanks,
Dwai.

Thanks Alex,
I found out -
ifconfig adapter plumb will fail with Bad File number error when the device file that is being referred to is missing.
I checked and found that the pcelx link is not being made in the /dev directory and the file not created in /devices.
I also found that when /reconfigure is run, it tries to create the device for pcelx but fails with this eror message:
pcelx : RequestIRQ fail 6
I am assuming that there is some IRQ conflict with some other device.
Thanks,
Dwai.

Similar Messages

  • Solaris boot images fail with bad magic number

    hi guys, have had Solaris on boxes for allmost 10 years. I have never installed sol10, and I have a problem
    1. I download the zip file, then use winrar to unzip them..
    2. burt the image with nero 7
    when my SunBlade 1000 comes up I do the Stop-A, and from the Ok promt
    I do boot cdrom
    this fails with "bad magic number" I have redown loaded it and reburnt it with nero reinstalled
    and also changed out the DVD on SunBlade
    3 I found a copy of Solaris 8 and the I got back a 'bitch' where is Solaris 9 so, most likely the drive is OK
    HELP
    Cris Harrison

    Hello Cris,
    unfortunately I don't understand your last sentence !
    I found a copy of Solaris 8 and the I got back a '*****' where is Solaris 9 so, most likely the drive is OK
    If this was a Solaris 8 (7/01 or later) DVD that did successfully boot, your DVD drive firmware (assuming that this is the Sun Toshiba SD-M1401) is up-to-date. If the DVD drive has firmware 1007, an update to 1009 is required to boot from DVD. otherwise you won't be able to boot from DVD (boot from CD works and a DVD can be automounted/mounted).
    Partial output of probe-scsi
    Before update:
    Unit 0 Removable Read Only device TOSHIBA DVD-ROM SD-M14011007
    After update:
    Unit 0 Removable Read Only device TOSHIBA DVD-ROM SD-M14011009
    [*Patch 111649-04 - Toshiba DVD 1401 firmware update*|http://sunsolve.sun.com/search/advsearch.do?collection=PATCH&type=collections&queryKey5=111649&toDocument=yes]
    when my SunBlade 1000 comes up I do the Stop-A, and from the Ok promt ...
    Instead of trying to directly boot, disable auto-boot and retry after a clean power-on.
    Break with Stop-A
    setenv auto-boot? false
    reset-all
    boot cdrom
    Michael

  • Fsck fails with bad inode number 0 to ginode

    Hi,
    I'm trying to repair a ufs filesystem on Solaris 10 but it keeps failing with the message:
    bad inode number 0 to ginode
    Does anyone know how to get around this issue?
    Thanks,
    Ted

    I had this identical failure and the only solution I found anywhere was to format the drive, but I tried an alternate strategy which worked..
    The inode failure repeated during Phase 3 of fsck. I answered NO, to the Reconnect prompts during that Phase, and answered Yes to the Phase 4 & 5 prompts. After serveral fsck runs, Phase 4 & 5 errors were all fixed. On the next run of fsck, Phase 3 also passed - the bad inode error was gone.
    I could then mount the drive READ/WRITE and restore a corrupted library file. The server then booted up clean.
    The fix took less than 30 minutes...much better than the nuclear option!

  • Backup failed with tar file write error (10054)

    Hi
    I have got the issue with the online backup.
    Database: Oracle 9.2.0.7
    SAP : 4.7
    Backup Server: Netbackp
    When ever i trigger the backup on few of my SAP Servers, it runs for a while and then at a point just get struck.
    Where for other systems it is running fine.
    Error:
    Incident:1
    http://80.00 18:52:28 INF - Waiting for mount of media id A00201 on server mk2sapp001-b.
    http://80.00 18:53:42 INF - Beginning backup on server mk2sapp001-b of client mk1sap01-b.
    http://80.00 18:55:10 FTL - tar file write error (10054)
    Incident:2
    http://80.00 12:05:50 BKR - G:\oracle\VWD\sapdata1\btabd_41\
    http://80.00 12:05:53 INF - Beginning backup on server mk2sapp001-b of client mk1sap01-b.
    http://80.00 12:08:13 FTL - tar file write error (10054)
    http://80.00 12:08:13 INF - Client completed sending data for backup
    After the step mentioned in bold it just get struck,
    There is no issue with the space at OS level
    I can see all process will still be running in task manager
    such as backint.exe, brbackup.exe, brconnect.exe
    But
    I don't find bpbkar32.exe Process, after the backup got struck.
    I have asked Network guys as well and they said every thing is fine from their side(such as Speed, Full Duplex)
    Its very important, please assist.
    Thanks in advance

    yes , i am using symantec netbackup,
    but every thing is fine from their side as well(settings).
    i have reinstalled the client as well.
    it runs for 1 hr and then it throws error.
    yesterday i scheduled two backup at two different time(at the interval of 1 hr) but they both failed (struck) at the exact same time(even seconds were same).
    So what do you say??

  • Create project from template failed with "badly formed pathname" error message

    Hi,
    I am trying to create a project from a custom template, but I am getting the following error message prompt:
    LabWindows/CVI could not create
    Test_Project
    because of an error: Badly formed pathname
    However, when I checked the target project directory, I see the project files are copied correctly.  I don't know if there is something missing from our custom templates?  Of, if there is something wrong with our custom template?
    I am using LabWindows/9.0
    Thank you.
    Peggy

    Hi Peggy,
    Did I understand you correctly that the files for the new project appear to have been created, but the error dialog still shows? In addition to Wolfgang's suggestions, take a look at the help section on New Project and File Templates. This describes everything that should be needed to create a custom template. Also, try to create a new, very basic custom template and make sure that you can use it successfully. If you can, start adding in the functionality of the original template, and test along the way. Hopefully either this new one will work once you finish, or you will see at which point it is breaking, and we can debug from there.
    Best Regards,
    John M
    National Instruments
    Applications Engineer

  • Re: Bad File Number Closing.....

    Just a thought-
    Is this Windows? Make sure you have a large enough "FILES"
    parameter in your CONFIG.SYS, etc. I seem to recall problems similar
    to what you describe when we didn't have it high enough.
    Make sure to re-boot after changing the "FILES" parameter..
    Also, if you encounter or generate exceptions, be very careful to
    catch them and close open files! Otherwise in the course of testing your
    application you will slowly use up the available file handles and get
    problems more often. Quitting the application (in the
    Development Workshop) does not free the handles --
    Quitting Forte completely does.
    Hope this helps.
    -Greg
    To: forte-users <[email protected]>
    From: Michael George <[email protected]>
    Date: 8 Nov 96 14:59:43
    Subject: Bad File Number Closing.....
    Reply-to: Michael George <[email protected]>
    Has anyone ever encountered the Bad File Number error when closing a file
    object. This is a random error that is causing us major grief. We can run our
    application 6 or 7 times before we eventually receive the bad file number error
    when executing the "close" method. Incidentally, this same error occurs when
    you import a new project into your workspace, and then try to import the exact
    same project again (overwriting the first one).
    We tried using the "Flush" method before closing, we also tried deleting the
    text file after we closed it each time. But nothing seems to be helping. Any
    help would be appreciated.
    Greg Nyberg, Senior Consultant
    Born Information Services Group
    Phone: (612) 404-4217 Fax: (612) 404-4440
    ------------------------------------------------------

    Thanks for your prompt answers.
    Are your two processes on two different hosts accessing a common NFS file system? If so, all bets are off.We have processes from multiple (hundreds in fact) boxes accessing common NFS system. With a careful design of one process accessing BDB at a time, we have pretty good success. Millions of BDB GET/PUT per day are succeeding just fine. Occasionally we see this bad file number error in different scenario of GET/PUT/CLOSE.
    Came up on the following article in a google search which indicates that a JDK bug may be causing this behavior.
    http://256.com/gray/docs/misc/java_bad_file_descriptor_close_bug.shtml
    We are running 1.5.0_11-b03 currently. We will try to upgrade the JDK and see if the problem goes away. Upgrading is a slow process though.
    The cleaner is the only thing that deletes a log file so it must be running somehow.We are explicitly disabling cleaner by setting e.env.runCleaner to false. Let me know, if the cleaner can still run somehow.
    Does closing the environment in all threads of the process that receives the exception and then reopening the environment clear the problem? Note that unless you do Environment.close() on all Environment handles, the Environment will not get truly closed. In cases when GET and CLOSE fail because of "Bad File Number", things are recoverable. When PUT fails because of "Bad File Number", we are loosing user data which is bad.

  • IOException :Bad file number

    Hi All
    I have written a program which writes into the file and reads from the file.
    I encounter bad file number error whenever I create new jar and replace it with old one.
    Actually file handle writes into the file correctly initially but after 5-6 operations I get bad file number error.
    Whenever I get this error then I close my application and start it again.after that I never face any issue.
    I am using solaris 9 OS and jdk1.6.
    I am using FileOutputStream to write into the File.
    Please let me know If you need more info?

    In my case, this exception was due to a defect in some timeout code I'd written. I didn't want to wait forever for the command to complete, so after an appropriate amount of time, the code would destroy the process. That invalidated the data streams however, causing the bad file number exception in the reader threads.
    So you may look for ways in which the executed process might be getting destroyed.

  • Export for system copy fails - Error 9 (Bad file number)

    Hello all,
    I am attempting to perform the export phase for a hetergenous system copy on our BI system (BI 7.0 - NW2004s).  This system runs on HP-UX 11.11 using Oracle  10.2.0.2 and will be migrated to Windows Server 2003 and MS SQL Server 2005, once the export is complete.
    While running sapinst to export the data from the source system, there are several input dialog screens that are skipped, which means I am not able to enter all the paramters used for the export.  After seeing this behavior from sapinst, I reviewed the sapinst.log and sapinst_dev.log files and find the warning/error "System call failed. Error 9 (Bad file number)".  I have included a portion of these files below.
    I have reviewed notes 546006 and 583861, but these seem to refer to an Oracle error ORA-27121, but I am not receiving any Oracle errors in sapinst.log or the Oracle alert log.  I have looked for possible permission or ownership problems with any of the SAP or Oracle files, but have not found any that were incorrect.  Also, these errors do not specify which file sapinst is having problems with, so I do not have  a specific file or area to check.
    If anyone has seen something similar to this and has any suggestions, I would greatly appreciate any help.
    sapinst.log details:
    INFO 2009-02-14 15:15:51.67
    Execute step collect of component |NW_Export|ind|ind|ind|ind|0|0|NW_GetSidFromProfiles|ind|ind|ind|ind|1|0|NW_readProfileDir|ind|ind
    |ind|ind|0|0
    INFO 2009-02-14 15:15:52.737
    Account bwpadm already exists.
    WARNING 2009-02-14 15:15:52.747
    System call failed. Error 9 (Bad file number) in execution of system call 'getgrent' with parameter (), line (292) in file (syuxcuse
    r.cpp).
    INFO 2009-02-14 15:15:52.757
    Account 0 already exists.
    WARNING 2009-02-14 15:15:52.777
    System call failed. Error 9 (Bad file number) in execution of system call 'getgrent' with parameter (), line (292) in file (syuxcuse
    r.cpp).
    INFO 2009-02-14 15:15:52.777
    Account 200 already exists.
    WARNING 2009-02-14 15:15:52.827
    System call failed. Error 9 (Bad file number) in execution of system call 'getgrent' with parameter (), line (292) in file (syuxcuse
    r.cpp).
    INFO 2009-02-14 15:16:04.937
    Creating file /tmp/sapinst_instdir/NW04S/LM/COPY/ORA/EXP/CENTRAL/AS/EXP/ypcat.log.
    INFO 2009-02-14 15:16:05.007
    Output of ypcat passwd.byname is written to the logfile ypcat.log.
    sapinst_dev.log details:
    TRACE      2009-02-14 15:15:52.737
    2009-02-14 15:15:52.743 NW._getSAPMount() done: /sapmnt
    INFO       2009-02-14 15:15:52.737 [syuxcaccmg.cpp:227]
               bool CSyAccountMgtImpl::isExisting(ISyAccountMgt::eAccountType accountType, iastring sName)
    Account bwpadm already exists.
    TRACE      2009-02-14 15:15:52.747 [syuxcuser.cpp:1943]
               CSyUserImpl_getOsInfos(ILogBook *m_logBook, iastring sName, iastring sID, tSyUserInfo& msUserinfo)
    getspnam(bwpadm) returned NULL.
    WARNING    2009-02-14 15:15:52.747 [syxxsyshlp.cpp:78]
               syslib::printOSError(const iastring &, int, DWORD, const iastring &, CMessage::eLogMessage)
    System call failed. Error 9 (Bad file number) in execution of system call 'getgrent' with parameter (), line (292) in file (syuxcuse
    r.cpp).
    Regards,
    Rusty Robbins

    Hello Peter,
    Thanks for the reply. I did confirm the points you made, and have the details below.
    1. check filesystem, if you have enough space, especially /tmp
    All filesystems have available space, and /tmp has 310 MB available, before the start of sapinst.
    2. check again alert log, trace log for Oracle,
    I could not find any errors in the alert_SID.log or any unusual trace files.
    3. How did you run sapinst? Are you using "root" account.
    I am running sapinst as user root and I am following all the recomendations in the system copy guide (at least as far as I can tell.  ;p )
    We have four BI systems in this landscape, and the other three have migrated successfully.  The procedure I am using, is the same as for the other 3 systems and uses the same SAP media directory that was used on the other systems.
    One other item that may be part of my problem here, is that this system is the production system, and was originally installed as a high-availability system, using HP-UX Service Guard for clustering.  Currently, this system does not have fail-over enabled, but of course the cluster is still intact.  One required piece of the Service Guard enviornment is the use of a virtual hostname.  This seems to resolve successfully by sapinst, as I see the correct (virtual) hostname referenced several times.  While this is a clustered system (for fail-over purposes), the CI and DB are installed on the same host.  So it is not a distributed system, and if failover had been initiated, it would fail both the CI and DB instance, which is the same and only SAP instance.
    This did raise one question in my mind, however.  I am attempting to extract this using the following menu path within sapinst.
    SAP NetWeaver 7.0 Support Release 3  --> Software Life-Cycle Options --> System Copy --> Oracle --> Source System Export --> Central System --> Based on AS ABAP and AS Java
    Since this does use Service Guard, but is not a distributed system, should I be using a different path in the sapinst tree, for the export?  I have only performed a migration using the above path, so I am not familar with the detailf of the other types, such as High-Availabitly or Distributed-System.
    Regards,
    Rusty

  • Exception clearing file manager: java.io.IOException: Bad file number

    I see the following exception when closing the environment. Not reproducible easily, happens only with production user's data occasionally. Any ideas on what causes this and what can be done to resolve it?
    com.sleepycat.je.RunRecoveryException: (JE 3.2.74)
    Exception clearing file manager: java.io.IOException: Bad file number
    at com.sleepycat.je.dbi.EnvironmentImpl.doClose(EnvironmentImpl.java:1123)
    at com.sleepycat.je.dbi.EnvironmentImpl.close(EnvironmentImpl.java:995)
    at com.sleepycat.je.Environment.close(Environment.java:322)

    Thanks for the pointers.
    We are running on Solaris.
    I located a narrow window in our code where another thread from the same process was permitted to close the environment when a close is already in progress. Will plug that window.

  • Bad file number - comes when i upload the file

    While i tried to upload the file more 300 kb (any file type)to 2 apache server using nfsmount (nfsmnt-apache 1 and nfsmnt2 -apache 2) through weblogic 9.2 (it is running in linux), i got the following exception, but less 200kb file i can upload the file (any type) to both apache server.
    java.io.IOException: Bad file number at java.io.FileInputStream.readBytes(Native Method) at java.io.FileInputStream.read(FileInputStream.java:177) at
    anybody known this prob, pls help me

    Suggestion: read [the documentation|http://commons.apache.org/fileupload/using.html] for it.
    By default it will store files in memory up to about 10k. Larger than that will be written to disk.
    If you are really worried about memory, perhaps you should take a look at the [streaming API|http://commons.apache.org/fileupload/streaming.html]
    How large are the files being uploaded?
    How many users are we talking about?

  • SQLException: Io exception: socket closed: Bad file number;

    Hi,
    My server application connects oracle 8i using thin driver.
    My code opens a connection and create a statement object:
    DriverManager.registerDriver(new oracle.jdbc.driver.OracleDriver());
    Connection connection = DriverManager.getConnection(url, username, password);
    connection.setAutoCommit(false);
    Statement statement = connection.createStatement();
    After a few hours it runs just fine I get the following error:
    java.sql.SQLException: Io exception: socket closed: Bad file number;
    The code line that couses this exception is:
    statement.executeQuery("my SQL query");
    after this there are more errors:
    ;java.sql.SQLException: Protocol violation;
    (in code line: connection.execCommit())
    and than a repeated exception of :
    java.sql.SQLException: Io exception: Broken pipe;
    Does anyone knows a solution? (is the problem in my code or in the oracle account?)
    Thank!!!

    Which package you are using? if you don't have
    classes12.zip, try again by including that package in
    the classpath. If you are already using classes12.zip
    then try by including nls_charset12.zip in the
    classpath.
    You can get these packages in Oracle (otn) website.
    SudhaThanks!
    I had classes12.zip in my classpath, but my classpath also had: classes111.zip
    so i removed classes111.zip from the classpath and as far as now,
    the problem did not occur again!
    (i also added nls_charset12.zip just to be sure)
    Lilach

  • ISE upgrade failing with "% Manifest file not found in the bundle"

    Hello
    I am trying to upgrade a brand new ISE 3395 from 1.0.3.337 to 1.0.4 (latest).  It keeps failing with
    % Manifest file not found in the bundle
    Here is the output:
    company-ise-01/admin# application upgrade ise-appbundle-1.0.4.573.i386.tar.gpg ftp
    Save the current ADE-OS running configuration? (yes/no) [yes] ?
    Generating configuration...
    Saved the ADE-OS running configuration to startup successfully
    Initiating Application Upgrade...
    % Manifest file not found in the bundle
    fusd-ise-01/admin# sh application version ise
    Cisco Identity Services Engine
    Version      : 1.0.3.377
    Build Date   : Fri May  6 19:30:37 2011
    Install Date : Wed Oct 12 22:18:26 2011
    I can't find anything about this for ISE, although there are a lot of topics for the same error for ACS.  Thanks in advance.
    Saro

    Same problem with 1.1.2 and 1.1.1 patch 5:
    ISEcdemo/admin# sh ver
    Cisco Application Deployment Engine OS Release: 2.0
    ADE-OS Build Version: 2.0.4.018
    ADE-OS System Architecture: i386
    Copyright (c) 2005-2011 by Cisco Systems, Inc.
    All rights reserved.
    Hostname: ISEcdemo
    Version information of installed applications
    Cisco Identity Services Engine
    Version      : 1.1.1.268
    Build Date   : Mon Jun 25 05:49:23 2012
    Install Date : Wed Sep 12 09:12:53 2012
    Cisco Identity Services Engine Patch
    Version      : 1
    Install Date : Wed Sep 12 10:01:22 2012
    Cisco Identity Services Engine Patch
    Version      : 2
    Install Date : Wed Sep 12 13:10:36 2012
    Cisco Identity Services Engine Patch
    Version      : 3
    Install Date : Tue Nov 27 12:33:19 2012
    Cisco Identity Services Engine Patch
    Version      : 4
    Install Date : Tue Nov 27 12:52:50 2012
    ISEcdemo/admin# patch install ise-patchbundle-1.1.1.268-5-68046.i386.tar.gz my2
    Save the current ADE-OS running configuration? (yes/no) [yes] ? yes
    Generating configuration...
    Saved the ADE-OS running configuration to startup successfully
    Initiating Application Patch installation...
    % Manifest file not found in the bundle
    ISEcdemo/admin#
    ISEcdemo/admin# application upgrade ise-appbundle-1.1.2.145.i386.tar.gz my2
    Save the current ADE-OS running configuration? (yes/no) [yes] ? yes
    Generating configuration...
    Saved the ADE-OS running configuration to startup successfully
    Initiating Application Upgrade...
    % Manifest file not found in the bundle
    Can someone verify the downloaded file details? They are different from cisco.com values:
    -bash-4.1$ /usr/bin/md5sum.exe /cygdrive/c/munka-unenc/tftp/ise-appbundle-1.1.2.145.i386.tar.gz
    2aa9b75ef5d7c1662a1a51844f178b77 */cygdrive/c/munka-unenc/tftp/ise-appbundle-1.1.2.145.i386.tar.gz
    -bash-4.1$ /usr/bin/ls -lAp /cygdrive/c/munka-unenc/tftp/ise-appbundle-1.1.2.145.i386.tar.gz
    -rwx------+ 1 Administrators Domain Users 1583851520 Nov 29 00:14 /cygdrive/c/munka-unenc/tftp/ise-appbundle-1.1.2.145.i386.tar.gz

  • I ran an iTunes update.  It failed with the message  System Error.  The program can't start because MSVCR80.DLL is missing from your computer.  Try reinstalling the program to fix this problem.   I tried reinstalling but get the same message.

    I ran an iTunes update.  It failed with the message  "System Error.  The program can't start because MSVCR80.DLL is missing from your computer.  Try reinstalling the program to fix this problem."   I tried reinstalling but get the same message.  I looked in my Recycle Bin for that file name but there is none there.  Is this a new file that iTunes wants?

    Click here and follow the instructions. You may need to completely remove and reinstall iTunes and all related components, or run the process multiple times; this won't normally affect its library, but that should be backed up anyway.
    (99683)

  • An update of iMovie failed with the message "an error has occurred." That message remains posted by iMovie on the Mac App Purchases page. iMovie is now unavailable. It will not start, update, or reinstall from purchases page. How reinitialize app?

    An update of iMovie failed with the message "an error has occurred." That message remains posted by iMovie on the Mac App Purchases page. iMovie is now unavailable. It will not start, update, or reinstall from purchases page. How do I reinitialize the app?

    Thank you again. Here's the console messages from trying to open iMovie and then opening the App Store. Clicking on the iMovie icon in App Store purchases and clicking on check for unfinished downloads:
    8/28/14 4:56:26.743 PM Dock[214]: LSOpenFromURLSpec(file:///Applications/iMovie.app/) failed with -10699
    8/28/14 4:56:47.878 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:56:47.879 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:57:50.201 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:57:50.201 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:35.745 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:35.745 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:35.824 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:35.824 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:35.847 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:35.847 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:36.276 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:36.276 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:39.448 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:39.448 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:39.449 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:39.449 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:55.996 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:55.996 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.021 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.022 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.051 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.052 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.342 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.342 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.411 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.411 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.425 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.425 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.508 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.508 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.518 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.519 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.696 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.696 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.808 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.808 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.826 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.827 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.838 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.839 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.843 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.843 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.857 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.857 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.893 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.894 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.907 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.907 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.923 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.924 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:56.969 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:56.970 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:57.039 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:57.039 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:57.045 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:57.045 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:57.145 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:57.145 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:57.231 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:57.231 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:57.249 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:57.249 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:57.293 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:57.293 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:57.350 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:57.350 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:57.352 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:57.353 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:57.400 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:57.400 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:57.402 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:57.402 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:59.814 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:59.814 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:58:59.932 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:58:59.932 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:00.697 PM acwebsecagent[127]: Connection : Failed to connect to 167.8.226.9:80. Code : 60
    8/28/14 4:59:00.698 PM acwebsecagent[127]: Connection : Caught exception. Code : 60
    8/28/14 4:59:00.698 PM acwebsecagent[127]: Connection : Failed to connect externally. Code : 60
    8/28/14 4:59:01.352 PM acwebsecagent[127]: Connection : Failed to connect to 167.8.226.9:80. Code : 60
    8/28/14 4:59:01.352 PM acwebsecagent[127]: Connection : Caught exception. Code : 60
    8/28/14 4:59:01.352 PM acwebsecagent[127]: Connection : Failed to connect externally. Code : 60
    8/28/14 4:59:01.402 PM acwebsecagent[127]: Connection : Failed to connect to 167.8.226.9:80. Code : 60
    8/28/14 4:59:01.402 PM acwebsecagent[127]: Connection : Caught exception. Code : 60
    8/28/14 4:59:01.402 PM acwebsecagent[127]: Connection : Failed to connect externally. Code : 60
    8/28/14 4:59:26.564 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:26.565 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:26.660 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:26.660 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:26.840 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:26.840 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:26.864 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:26.864 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:26.984 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:26.984 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:27.069 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:27.069 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:27.079 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:27.079 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:27.083 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:27.084 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:27.385 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:27.385 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:27.389 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:27.390 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:27.391 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:27.391 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:27.411 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:27.411 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:27.435 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:27.436 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:27.443 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:27.443 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:27.479 PM acwebsecagent[127]: Connection : Auth key is not provided or is invalid, applying connection failure policy. CMode : 2 TMode : 1
    8/28/14 4:59:27.479 PM acwebsecagent[127]: OnConnectionFailure : Fail Open - Reason = Unable to verify the license key
    8/28/14 4:59:31.036 PM acwebsecagent[127]: License : One or more of the License/Public Key can't be NULL
    8/28/14 4:59:31.036 PM acwebsecagent[127]: SSLExt : Failed to get ScanSafe headers
    8/28/14 4:59:31.036 PM acwebsecagent[127]: DownloadUpdatedConfig : Failed to download updated config. Host hostedconfig.scansafe.net. Code 0x80004005

  • [ADI]Budget upload fails with "A run-time error has occured:...

    제품 : FIN_GL
    작성날짜 : 2003-11-20
    [ADI]Budget upload fails with "A run-time error has occured:...
    ===========================
    PURPOSE
    아래의 오류사항에 대한 해결
    Budget upload fails with "A run-time error has occured:current task will terminate".
    Problem Description
    ADI를 이용하여 GL의 Budget자료를 upload시 오류
    Workaround
    Solution Description
    Client PC에서 regedit를 이용하여 NLS_LANG값들을 applications의 NLS_LANG과 같은 값으로 바꿔주세요
    Reference Documents
    -------------------

    Hi Krishna
    Thanks for your reply, it was while trying to "edit" the page containing the shockwave file however it’s a bit of a strange one, as When I reposted this post , I had been experiencing the problem for about a week.  I then went on leave for a week and when I returned it started working again???.  I queried with my IT department if anything had changed or been updated but they could not think of anything.
    So for now it's working, but if you have any thoughts on what may of happened I would appreciate any suggestions?
    Thanks again
    Luke

Maybe you are looking for

  • Using iMac 27 as a display for a PC, is it possible?

    is there a way to connect my PC (HD 4870 dvi) to the imac 27 to use it as a display? and if so, what cables and adapters do i need? thanx ilya

  • File too large on export

    When trying to copy or move a quicktime file created with FCP X I keep getting th error File format too large. AM I missing a step?

  • AFP not letting users log in

    AFP is not allowing the Open Directory users to authenticate and access the server of you use Go to Server. From the Finder sidebar it will work.

  • How to use HTML form vi

    Hi, I am trying to trying to fill up information into a website using labview. It has 3 text inputs and a image submit button. I was wondering if it is possible to fill the HTML with labview. Another question is that if anyone knows an example VI for

  • Scanner is misssing edge of image

    Scanner B210a has been working fine but is now missing 1/2 inch of front edge when reprinting photos. Curious though, when scanned from computer we get all the image. Tried restoring factory defaults and switching off and on a few times - no effect.