FXO doesn't detect busy signal after transfer

If I'm calling on voice-port, it will pickup give me dialtone, press internal number then hangup on my side. Extension will call about 2 minutes
It's seems it doesn't monitor line in transfer, because if I do enable connection plar opx, its will stop calling almost immediately after far end hangup
here is part of my config:
voice-port 0/2/0
translation-profile outgoing moscow
supervisory disconnect dualtone mid-call
supervisory answer dualtone
supervisory custom-cptone PSTN
supervisory dualtone-detect-params 1
no battery-reversal
cptone RU
timeouts call-disconnect 1
timeouts wait-release 1
description 264-09-96
caller-id enable

Could lyou provide the detials of
sh call active voice,
debug voip ccapi inout.
debug vpm signal

Similar Messages

System Doesn't detect USB headset after suspend/resume

Sometimes (this seems to happen randomly), after a resume from suspend my USB headset is no longer detected in gnome. It doesn't show up in the sound settings output tab, and unplugging/replugging the headset does nothing. It does seem to show right up if I run pulseaudio -k to restart pulseaudio. It doesn't seem to matter if I suspended with the headset plugged in or not.
Has anyone else run into this issue, any workarounds or fixes?
Last edited by bwat47 (2012-02-28 20:03:14)

Let me quote archwiki here:
Standby / Suspend to RAM
In the ideal case, running sudo pm-suspend should initiate suspend to memory, meaning that all running state will be preserved in RAM and all components other than RAM will be shut down to conserve power. Pressing the power button should initiate a resume from this state.
In some cases, it is possible that running pm-suspend causes hangs or other issues. This may be due to specific "misbehaving" modules. If you know which modules could cause such issues, adding a SUSPEND_MODULES config to /etc/pm/config.d/modules of the form
SUSPEND_MODULES="uhci_hd button ehci_hd"
should cause these modules to be specifically unloaded before suspend and reloaded after resume.
To configure invoking pm-suspend automatically on power events like laptop lid close, please refer to Acpid.
and exactly those 2 modules you should add in the same way.. because those are responsible for usb... helped for me...
Last edited by Rasi (2012-02-28 21:21:46)

Walkman and Album doesn't detect any media after reboot

I have just purchased a Sony Xperia Z1 for 1 week now, and I haven't got any problems with it until now.
For the first 5 days, it worked out fine. Then after I powered the whole thing off in order to charge it more effectively, and when I powered it on after that, I noticed something was not right. First, I can't find any of my pictures in my albums, the images were ' undetected ' by the album, like they were hidden out of sight or something. Then my walkman couldn't detect any songs that I have previously saved, which was working fine and my playlists were gone. I can access them using the file manager but the albums and walkman and movies apps were not able to detect those files. I tried downloading other photo viewer, video viewer and a music player app but they can't detect those files for some reason. And now I can't even access my mobile data.
Help?
Topic edited by Rickard

http://talk.sonymobile.com/t5/FAQ/How-to-boot-your-phone-into-safe-mode/m-p/348008#U348008
if that doesn't work, repair your phone with
Update Service (SUS)
PC Companion (PCC)
Bridge (for Mac)
Alternatives on How to backup Xperias
http://talk.sonymobile.com/thread/36355
"I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

[solved] Pulseaudio doesn't detect sound card after system update

Before a recent system update I had pulseaudio working flawlessly, but after doing a recent system update with pacman -Syu,
pulseaudio no longer sees my sound card and only displays the Dummy audio device. Among the packages updated that I can
remember off the top of my head are the Linux keneral, udev, kmod, instead of trying to roll back my system I figured I would try
to fix the issue. The only thing suggested in the Pulseaudio wiki is that a asound.conf directory is overriding the /etc/asound.conf
file which is not the case on my system.
Looking at the output from lsmod I can see where the kernel modules for the sound card is getting loaded
snd_hda_intel 23375 0
snd_hda_codec 89160 3 snd_hda_intel,snd_hda_codec_realtek,snd_hda_codec_hdmi
snd_hwdep 6389 1 snd_hda_codec
snd_pcm 74780 3 snd_hda_codec,snd_hda_intel,snd_hda_codec_hdmi
snd_page_alloc 7153 2 snd_pcm,snd_hda_intel
snd_timer 19544 1 snd_pcm
and looking at the output from the ps command I can see that pulseaudio is getting started
1190 ? S<l 0:00 /usr/bin/pulseaudio --start
1195 ? S 0:00 \_ /usr/lib/pulse/gconf-helper
but pacmd list still reports this
0 card(s) available.
0 sink input(s) available.
0 source outputs(s) available.
0 cache entrie(s) available.
Here is the output of pacmd dump if it helps
### Configuration dump generated at Thu Feb 16 08:45:56 2012
load-module module-device-restore
load-module module-stream-restore
load-module module-card-restore
load-module module-augment-properties
load-module module-udev-detect tsched=0
load-module module-jackdbus-detect
load-module module-bluetooth-discover
load-module module-esound-protocol-unix
load-module module-native-protocol-unix
load-module module-gconf
load-module module-default-device-restore
load-module module-rescue-streams
load-module module-null-sink sink_name=auto_null sink_properties='device.description="Dummy Output"'
load-module module-always-sink
load-module module-intended-roles
load-module module-suspend-on-idle
load-module module-console-kit
load-module module-position-event-sounds
load-module module-cork-music-on-phone
load-module module-filter-heuristics
load-module module-filter-apply
load-module module-dbus-protocol
load-module module-x11-publish display=:0.0
load-module module-cli-protocol-unix
set-sink-volume auto_null 0x10000
set-sink-mute auto_null no
suspend-sink auto_null yes
set-source-volume auto_null.monitor 0x10000
set-source-mute auto_null.monitor no
suspend-source auto_null.monitor yes
set-default-sink auto_null
set-default-source auto_null.monitor
### EOF
EDIT: I should also add that fuser -v /dev/snd/* returns nothing and fuser -v /dev/dsp returns "Specified filename /dev/dsp does not exist".
Last edited by vendion (2012-03-02 23:26:28)

Digging into this further aplay -L gives different output based off of whether or not I ran is as my normal user or with sudo/as root.
As a user (which is how pulseaudio is also being ran):
> aplay -L
null
Discard all samples (playback) or generate zero samples (capture)
pulse
PulseAudio Sound Server
default
Default ALSA Output (currently PulseAudio Sound Server)
as root it does see both my sound cards when I run it with sudo or as root:
> sudo aplay -L
Password:
null
Discard all samples (playback) or generate zero samples (capture)
pulse
PulseAudio Sound Server
default
Default ALSA Output (currently PulseAudio Sound Server)
sysdefault:CARD=SB
HDA ATI SB, ALC887-VD Analog
Default Audio Device
front:CARD=SB,DEV=0
HDA ATI SB, ALC887-VD Analog
Front speakers
surround40:CARD=SB,DEV=0
HDA ATI SB, ALC887-VD Analog
4.0 Surround output to Front and Rear speakers
surround41:CARD=SB,DEV=0
HDA ATI SB, ALC887-VD Analog
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=SB,DEV=0
HDA ATI SB, ALC887-VD Analog
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=SB,DEV=0
HDA ATI SB, ALC887-VD Analog
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=SB,DEV=0
HDA ATI SB, ALC887-VD Analog
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=SB,DEV=0
HDA ATI SB, ALC887-VD Digital
IEC958 (S/PDIF) Digital Audio Output
hdmi:CARD=HDMI,DEV=0
HDA ATI HDMI, HDMI 0
HDMI Audio Output
This behavior is confusing to me, and if someone knows what is going on and how to fix it I really want to get sound with pulseaudio working and have sound again.

Airport Utility 6.0 doesn't detect my network after any change

10.7.3, Airport Utility 6.0, MacBook Pro and MacBook Air, Airport Extreme and Airport Express base stations
How does one get Airport Utility 6.0 to see their network again after making any changes to one of the base stations?
When you make any change to any of your base stations airport utility no longer detects your network. All it shows is the internet and it says not connected. All base stations are all up and in the green except for one. From the airport drop down I verify I am on my own network and I can browse normally, yet Airport Utility 6.0, on any connected computer, does not see the network. An older version of Airport Utility is able to see all base stations normally, it is only 6.0 that has the problem.
The only work around I have found is to take an extra base station and reset it. I join the new base station's default network. Airport Utility sets things up, and the network reappears. The trouble is, Airport Utility changes the name of the network to the name of the computer I'm on at the moment. When I use airport utility to change the name back my network disappears again (in Airport Utility. So, I guess I'll change the name of a computer to my network name and try again.
Does anyone have a better way to make the network reappear in Airport Utility? I have tried connecting directly, base stain to Mac on both the WAN and LAN ports of the base station. I have tried using a Mac with a fresh install of 10.7.3 and AP Utility 6.0. I have tried shutting down my network and starting with just the main AP base station. Any other ideas to make my network reappear in Airport Utility after making any change?
(Tried restarting, new user, other laptops, fresh install, only one base station0

10.7.3, Airport Utility 6.0, MacBook Pro and MacBook Air, Airport Extreme and Airport Express base stations
How does one get Airport Utility 6.0 to see their network again after making any changes to one of the base stations?
When you make any change to any of your base stations airport utility no longer detects your network. All it shows is the internet and it says not connected. All base stations are all up and in the green except for one. From the airport drop down I verify I am on my own network and I can browse normally, yet Airport Utility 6.0, on any connected computer, does not see the network. An older version of Airport Utility is able to see all base stations normally, it is only 6.0 that has the problem.
The only work around I have found is to take an extra base station and reset it. I join the new base station's default network. Airport Utility sets things up, and the network reappears. The trouble is, Airport Utility changes the name of the network to the name of the computer I'm on at the moment. When I use airport utility to change the name back my network disappears again (in Airport Utility. So, I guess I'll change the name of a computer to my network name and try again.
Does anyone have a better way to make the network reappear in Airport Utility? I have tried connecting directly, base stain to Mac on both the WAN and LAN ports of the base station. I have tried using a Mac with a fresh install of 10.7.3 and AP Utility 6.0. I have tried shutting down my network and starting with just the main AP base station. Any other ideas to make my network reappear in Airport Utility after making any change?
(Tried restarting, new user, other laptops, fresh install, only one base station0

FXO Trunk Group rings to a busy signal

I have setup a trunk group for my (4) FXO ports. The ports are all setup with "connection plar 2000" since all calls need to route to a parallel huntgroup of which the pilot is 2000. If I cann one of the POTS lines in the group and do not pick it up, the call goes to a busy signal after about 3 rings. I have final destination set to a script. Not sure on why I am getting the busy signal.
If stack up the calls on all phones the hunt group, the nex tell will route to the script just fine and not give a busy signal. Not sure if that gives any clues to my issue or not.
TIA, Jim

I will give it a try. Not sure what you mean about my english. I did see several typos and meant to say:
I have setup a trunk group for my (4) FXO ports. The FXO ports are all setup with "connection plar 2000" since all calls need to route to a parallel huntgroup of which the pilot is 2000. If I CALL one of the the lead POTS line and do not pick it up the call on a phone that is in the hunt group, the call goes to a busy signal after about 3 rings. I have huntgroup final destination set to an auto attendant script. Not sure on why I am getting the busy signal.
If I stack up the calls on all phones the hunt group by calling, answering them, and putting them on hold, the next call beyond the number of phones I ahve in the huntgroup does route to the script just fine and not give a busy signal. Not sure if that gives any clues to my issue or not.
Jim
Tags: trunk, group, hunt

Fast busy signal with incoming calls and unable to connect to voice mail

We are using CISCO 2821. The system started to have problem connecting to voice mailbox (when dialing internally to the VM extension) and it used to take a reboot to bring it back. Now it will not connect to voice mail (gets fast busy signal), plus incoming calls get a fast busy signal after the first ring tone. To make it worse, the Call Manager Express web page does not load. Does anyone have any idea how to solve the problem? Thanks!

Called ATT...they verified the problem and said it was an intermittent signal problem....
only issue is I have to keep the phone off to make sure I received voicemails....
Definitely NOT an iPhone problem, but an ATT problem.

HT5167 after I updated to 10.7.4 my macbook pro 2011 doesn't detect external display anymore what should I do?

after I updated to 10.7.4 my macbook pro 2011 doesn't detect external display anymore what should I do?

after I updated to 10.7.4 my macbook pro 2011 doesn't detect external display anymore what should I do?

Hi, my computer is not detecting any display, i'd been having this problem since i connected my computer to a tv, the tv burned up, and after that my port doesn't detect anything at all?? Was that the problem can I fix it.I have the lion 10.7.5.

Hi, my computer is not detecting any display, i'd been having this problem since i connected my computer to a tv, the tv burned up, and after that my port doesn't detect anything at all?? Was that the problem can I fix it.I have the lion 10.7.5. Dont know if I changed settings or something.

Hello,
It isn't the fw in Network you want o use or look at, that's for something completely different.
My first suspect is the Power Adapter on the LaCie has gone.
At the Apple Icon at top left>About this Mac, then click on More Info, then click on Hardware>Firewire, what is listed there?
Reset the Firewire bus
If your Firewire or USB isn't recognizing any device. A solution which has worked for some whose hard drive became invisible in 10.4 was simply to follow these four steps to reset the Firewire/USB bus:
1. Shut the machine down.
2. UNPLUG the power lead to the computer and any firewire/USB drive or devices.
3. leave it for 10 minutes.
4. Connect back up and reboot.
http://www.macmaps.com/firewirebug2.html

Ok so I use an hdmi connector on my iPhone 4S to watch netflix. But after I updated to iOS 7 it will not work my tv doesn't receive a signal. Does anyone have any insure to this please help .!.!.

Ok so I use an hdmi connector on my iPhone 4S to watch netflix. But after I updated to iOS 7 it will not work my tv doesn't receive a signal. Does anyone have any insure to this please help .!.!.

The 8 pin Lightning connector can only output 720p and lacks all iPod Out functionality unlike the full iPod Out functionality and 1080p that the 30 pin connector has and I suspect that they are coding iOS 7 specifically for the new devices which have severely reduced abilities and perhaps skipping adding the code needed for 30 pin devices to use their functionality with HDMI, etc.

After 4.3.4 update the ipPad is in Recovery mode and iTunes doesn't detect the device

Hello,
brand new Win7 installation, restored iTunes folder and installed latest 10.4. iTunes64 bit.
Hooked up both my iPad and iPhone4
Detected new firmware 4.3.4
and bang, both devices are now stuck into recovery mode.
No matter I set the iPad/iPhone into Recovery or DFU mode, iTunes will not detect any device for recovery.
Uninstall/Install iTunes => no change
The driver will display that the units is detected and in DFU or Recovery mode, but iTunes doesn't detect the device.
Tried TinyUmbrella etc but no fix
Any other hint?
Best Regards
Uwe

Place the device in DFU mode (google it) then restore.

Can I change the default wait time to redial after a busy signal?

If I fax using my external USB modem, and I get a busy signal, the system waits something like three minutes before redialing. Is there a way I can change that to 1 minute? I can't find the preference for that anywhere I've looked, but I'm betting it exists somewhere.
Thanks in advance,
rb

I'm not sure this will work, but you can try it. ..
Create a character style that does nothing but apply the contextual alternates attribute (check the box under OpenType Features inthe style defintion dialog). Then add a GREP style to your paragraph style to match the "a" and apply the character style you just created.

Apple Modem Busy Signal

I am using a fax program (Pagesender by Smile Software) and run into problems with recognition of a busy signal. It seems they are not being recognized and the program continues to attempt to connect. The support people for Pagesender state that it is the Apple Internal Modem that does not recognize a busy signal and recommend buying an external USB modem. I find it hard to believe that the Apple Modem does not recognize a busy signal. Is this true? If so, is there a fix? Is there a way to test the Apple Modem?

It is more than a busy signal, I think. I am having the same problem - I try to send a fax and something goes wrong, busy signal, no answer, whatever. If I delete the job and try to start over, the modem is reported as unavailable. I downloaded ZTERM to see if I could regress to 1991 and start controlling the modem with stone age Hayes AT commands, but it too reported that the modem port was unavailable.
There are hardware diags on one of the OS disks, but that won't do much good since the modem will work at least once. It takes some sort of software failure in the OS to trigger this condition. That is, the modem is probably fine but the kernel software running it is broken. It disappears at the lowest level - the port disappears - but only after it is used once and fails to connect.
There us no option to hang up the modem in the status icon, and I have not been able to get the modem speaker turned on either. If I can't hear what it is doing it makes it much harder to troubleshoot, but the thing just ignores the settings.
Not to get on the soap box too much, but these rocket surgeons need to stop worrying about what color the next iPod will be and start paying attention to what they are doing in their core business. Having to reboot to get the modem back if a fax number is busy is asinine. I haven't had to do that in Windblows since at least version 3.11, if then. This OS is deteriorating with each new release.
My gut tells me that they just don't care enough about the iMac G5 user base to test their software against that platform. The sound is broken, the modem is broken, the Firewire interface can't capture DVI without corrupting the hard disk, and mine has required six rebuilds just to get Tiger running even this badly. I used to think Macs "just worked" and Windblows "just didn't". Now that relationship is reversing - it is my 64-bit XP that "just works" and my 64-bit OS X that "just doesn't work".

PC DOESN'T DETECT ZEN MICRO

after I downloaded the latest firmware updates/drivers for my zen micro, my pc doesn't detect my player. i can't view songs via windows explorer, creative interface or windows media player.
i tried uninstalling and then re-installing all of the creative software from cd, but that didn't work.
everything worked before i installed the drivers...
please help?

i got my player to work on my pc again... FINALLY. in the device manager, i hit 'update driver' and my player was detected (at least signaled on the player). when i tried to access songs via windows explorer, it then said it wasn't detected and then the icon on the player was gone again.
sooo000, i hit 'update driver' again and again the icon reappeared on the player saying it was docked. while the icon was still there i reinstalled the driver (. ) and replaced the existing driver.
voila!! it works again!!! hopefully this post will help someone else out there. it's a great player and i'm just happy i can use it on my pc.
thanks everyone!

MacBook (Black) Airport card fail to detect and enable after wake

I have had problems with my internal Airport card, I was having problems when the macbook started with not airport card detection, card overheating after using, this happened randomly.
After a apple certificated distribuitor test (for warranty) they found that it was only the airport card, they changed. After that, I have less issues with airport, but I still have the problem that the airport card doesn't work (disabled) after wake from suspended mode.
Is it a software or hardware issue?
Any idea, suggestion or fix?
I really desappointed with mac performance/quality after these issues.

Hello,
I guess I'm having same issue like yours, but my card somehow start to work when I turn airport off then on again. Once macbook awake from sleep or suspended mode, the WIFI signal would shown in "weak" status, then turn "strong" suddenly, but the actual connection is very unstable. I need to turn off the card then on again every time to solve the problem. I tried SMC reset or other method, but the problem still remain...

FXO doesn't detect busy signal after transfer

Similar Messages

Maybe you are looking for