Green Power Center +fan controll

Is there a way to have the settings adjust automaticly when Windows opens? Because if I need to decrease the fan speed to "Max Power Saving" I need to enter this software and do it manually every time I log into Win. Is there any other way to control the fan speed, or any other software for download?
Motherboard: 790FX-GD70

Quote from: Rulo on 09-December-09, 12:04:23
I don't own that MOBO but I would suggest to look in the BIOS for SmartFan set up. That would get you the option to set up the fan a a minimun speed and the system will rev it up once it gets to the threshold temperature.
Good luck!
Didn't find anything for SmartFan in Bios, just Green Power, although doesn't seem to do anything in Auto mode.

Similar Messages

  • Green Power CPU Phase Control + C-STATE + Turbo Boost ?

    Does anyone know if we can turn on MSI's Green Power CPU Phase Control + Intel C-STATE + Intel Turbo Boost in BIOS all at the same time?  Any problems with doing this?  Does MSI's Green Power CPU Phase Control override or conflict with Intel's C-STATE?  And will Turbo Boost kick in if turned on when a core needs it even if Green Power CPU Phase Control and C-STATE are switched on?
    I really like the idea of the PC running cool and quiet when doing lite work, but would like full power on demand as well.
    Thanks.

    I'm using Intel speedstep (EIST) but i disabled c-state because this brings a unstable PC for me.
    I'm using also the greenpower genie and it works very well.
    When i don't need the power my PC falls back to 50% 2154MHz (this you can choose in the energy configuration of windows), when i play games or decode movies it goes up to 100% 4130MHz. And it is stable as a rock tested 24/7 prime 95 and OCCT and Intel burn test.
    My settings are=
    Eist enabled
    Turbo enabled
    C-state disabled
    Greenpower auto
    My CPU temp in idle is 24° cores 38° and this on aire (room temp 21°-22°) Load 100%=CPU 60 and cores 70°-72° ( prime stressing), gaming CPU 42°-45°.
    For more info on my sys. follow link and see my overclock and voltage settings.http://www.hardware.info/nl-NL/usersys/cm9xZ51mk2yd/view/
    I also changed cpu skew and ioh skew to 200ps so i don't get BSOD that says :cpu did not receive clock on time , but this is only necessary when i go above 178 MHz BCKL.

  • Green Power Crashing

    Does anyone else have problems with this program either crashing or not responding?  I do have my system overclocked, but stable.  Does this program always crash on an overclocked system?

    Also have problems with Green Power Center. 
    Crashes everytime I try to start it, on my Vista 32bit Danish.
    Overclock or no overclock doesn't matter keeps crashing.
    Hardware - se signature

  • Should i use Green Power mode in Msi control Center ???

    So all new to this control center on my board and was wondering should i use the green power mode in Msi Control center, it looks pretty cool but not sure if i should use it so anyone got any opinions ?.

    Quote from: Beavise on 02-February-15, 05:50:02
    If i do use the one in the bios what setting should i use ? i'm new to this stuff the boards i had always just did it by itself.
    What settings exactly? I have different board, as I said I don't have a disable option, only adjust the settings for target and fan speed in Hardware Monitor which is graphic.
    looks like this:
    http://www.hardwareheaven.com/reviewimages/msi-z87-g45-gigabyte-z87-d3hp/msi-bios6.jpg

  • MSI Control Center Green Power not Working

    Hey guys, Green Power in the MSI Control Center doesn't seem to report any power saving for me- see pic. I have Green Power turned on in the BIOS.

    Quote from: NovJoe on 11-July-11, 15:27:19
    The interface is to tell you at what speed and voltage that it is regulating from the stock numbers. That is the way of power saving readings.
    How come it doesn't report the "Total Power Savings" in watts?

  • Does Ambient Board control Power supply fan speed?

    I've been messing around with my Mac. My Power Supply fan is constantly running at 2800rpm's http://discussions.apple.com/thread.jspa?threadID=2306202&tstart=0
    I think I narrowed it down to a temp senor issue. But I don't know where the sensor is that controls the Fan speed of the power supply?

    I'm not a tech but if the Ambient Temperature board was providing faulty indication then I would expect all fan speeds to run higher, not just the Power Supply fan. If the fan is running fast it is probably either the fan itself or a faulty temperature sensor in the power supply. Also since the Ambient Temperature indicates 72 degrees that is a pretty good indication the board is functioning normally, if it were reporting a ridiculously high value such as 20 degrees warmer than room temperature than that would be an indication it was bad.
    I'm confused here. You've stated that you moved to a new office and the computer there is annoyingly loud. You seem to be trouble shooting the computer yourself. Does your company have an IT department? Have you let your boss know the computer reports an error code and needs to be fixed? Have you asked your boss if you could swap your current computer with your old one because this one is loud and makes it hard to concentrate on work?
    Message was edited by: Martin Pace

  • CPU Fan Control H61M-P21 (B3) Motherboard

    I have assembled the following system recently:
    H61M-P21 (B3) Motherboard
    Sandy Bridge Core i3 2120 (Retail box w/cooler)
    2 x 2 GB Crucial Desktop memory
    SAPPHIRE Radeon HD 6750 1GB
    OCZ Vertex 2 60 GB
    Generic Case
    Windows 7 Pro
    I have a couple of questions.
    1/  I've installed the MSI Control Center and in the green power section I can set the CPU fan to quiet which is really quite necessary since the retail cooler at full speed is really quite noisy.  What I find irritating is changes with the MSI Control Center are not persistent.
    Is there any way to set the CPU fan to quiet and make the change persistent across reboots, etc...?
    2/  The system goes to sleep and wakes up just fine.  However - the only way to wake it up from sleep is to press the power button.
    Is there a way to allow the system to wake up from sleep using the keyboard?
    Any and all advice/recommendations welcome.
    Thanks.

    So I've been browsing the Application Guide and I came across the following passage, "Every time you shut down the system, the configured setting will be restored to the factory default. If you want to use the saved settings, you have to load it every time by clicking the “Load” button."
    So that answers my question - no persistent save support.  So I have a new question.
    Can I launch the control center from the command line specifying a saved config file?  (If yes, obviously I could create a start up item and that would be good enough)

  • Fan control problem on Z77A-G45 Gaming

    Hi,
    I've got this problem: I have Z77A-G45 gaming mobo and thermaltake water cooler (water 2.0 performer) on cpu and, by default this motherboard makes this cooler work with full 2000 rpm, but if I open the msi utility program "Control center" and go in "Green power" tab and use "CPU fan control" it makes cooler to run normally with 850 rpm. But problem is, when I turn off or restart PC, it starts again with 2000rpm and I need to open that "Control center" again and click check "Cpu fan control" to make cooler work normally. So what is solution to this problem? How to make it remember "cpu fan control" option marked? I don't want to start this application manually everytime I boot my computer.

    Try entering bios and enable cpu smartfan and save on exit.

  • P67a gd65 b3 CPU fan control staying at 100% ?

    Has anyone been able to get the cpu fan to ramp up and down with temp via bios ? I'm using a Noctua d14 and i5 2500k.

    Quote from: TheRealBaloo on 15-March-11, 07:43:53
    Hi,
    FYI I have the same issue with my Cooler Master 520 on the same board with a 2600k, fan runs at 100% 24/7, was not able to find a solution yet, will let you know if I do.
    hey you might try to install the control center and then click on the green power tab and then click on the the pop down tab saying green power again and then near the bottom of the page you will see the only three fans that you can control and the RPM they are currently running at. you need to pull down the minues and you will get three options to choose from 100%-75% or 50% but when you choose what you want them to run at be sure to double click that setting or it will just revert back to the original setting.  once you have changed all you want then click apply tab at the very bottom of that page and listen to your fans drop in speed but before you close the page you will need to save that set up so once you verify that what i mentioned worked then click the save tab too and lable it what you want to call it! this should work! but also i use a mega helm rev b and i ended up using sysfan2 and sysfan1 on the mobo for my two fans attached to my cooler just so i could control them both I and hooked up my rear fan on my case to the cpu jack on the mobo! you should have some control of all your other fans threw the click bios, this all worked great for my set up! i have a 2600k and the same mobo and i use ddr3 patriot ram 2000 9-11-9-27.....hope this works for you and answers your questions....have fun!....................................... ........... "warzone"

  • FM2-A75IA-E53 green power settings keep resetting [Win 7 64]

    Quote from: mcgregorkd on Today at 01:01:57How long do you figure until the 5th generation CPUs begin to bottleneck?  Noticed they were soldered on to this mboard.
    Respectfully, I think your last statemen...

    I tried to ask this via support but it is impossible and won't let me ask. A hang during boot forced me to do a hard reset which somehow lost all my bios settings. Now every boot my "green power" custom config I've done in "Control Center" resets to th...

  • Fan Controlling Software Issues with K8N-Neo4-F

    My mobo is a K8N Neo4-F 3.0.
    1. Is there anyway to control the Northbridge and System fan using Speedfan? I searched so far without any solutions.
    2. I tried MSI Corecenter for a while (the last version), and it triggers the alarms and atempts to shut down the system without any visible reason everytime the PC comes backs from hibernation. I have the latest BIOS and latest drivers on my PC. What could be wrong?

    It could be the sensor is bad on the system fan or the header itself. Is it possible for the wire from the NBFAN1 to reach the CPUFAN1 and the wire from the CPUFAN1 to reach the NBFAN1?  That way we could test to see if it's the fan or MOBO header? I'm not sure this is possible, but it occurred to me as a test.  According to the manual, both headers have the same configuration and 12V feed. I think the amp specs are the same for both headers(someone that is better with electronics should speak up here). Make sure you have the CPU fan set to 100% or whatever as I'm not sure if the NB fan can or should be speed adjusted.
    According to page 2-16 of your manual, it only mentions control of the CPUFAN1 header:
    Quote
    Fan Power Connectors: CPUFAN1 / SFAN1 / SFAN2 / NBFAN1
    The CPUFAN1 (processor fan), SFAN1 (system fan 1), SFAN2 (system fan 2) and
    NBFAN1 (NorthBridge Chipset fan) support system cooling fan with +12V. It supports
    three-pin head connector. When connecting the wire to the connectors, always take
    note that the red wire is the positive and should be connected to the +12V, the black
    wire is Ground and should be connected to GND. If the mainboard has a System
    Hardware Monitor chipset on-board, you must use a specially designed fan with
    speed sensor to take advantage of the CPU fan control.
    MSI Reminds You...
    1. Always consult the vendors for proper CPU cooling fan.
    2. CPUFAN1 supports fan control. You can install Core Center utility
    that will automatically control the CPU fan speed according to
    the actual CPU temperature.
    3. Please refer to the recommended CPU fans at AMD® official
    website.
    But, In addition to finding out about this issue, I can't stress enough about getting a better PSU.

  • Re: p67a gd65 b3 CPU fan control staying at 100% ?

    I hate to be reviving this thread, but it's already got evidence of my problem.
    Basically, Only 2 out of the 4 PWM controllers on the motherboard (P67a-GD65) allow for fan control. This was fine originally, when I only had two fans in my case, but when I upgraded to a third and plugged it in, it simply ran at 100% speed. Multiple scans in speedfan only found the CPU control and two PWMs. Looking in the BIOS it only saw two as well, even though the third fan was plugged in and running at 100%.
    My BIOS version is the one just before the ivy bridge update, so the 'improved system fan control' apparently didn't help.

    Quote from: Henry on 28-May-12, 04:09:10
    * There are only 2 PWM not 4, CPU fan & sys fan 1. The others are fan speed monitoring only and are not speed controlled.
    * Where do you get the idea that there is Ivy update for P67? The latest BIOS is 1.I:
    Update CPU Micro Code for Sandy Bridge C2 CPU
    The BIOS update page [http://www.msi.com/product/mb/P67A-GD65.html#/?div=BIOS];[Won't let me hyperlink] shows '- Update BIOS for IvyBridge 22nm CPU.' for BIOS v4. I nabbed version 1.19 because I have an i3-2100.
    The CPU fan is PWM controlled, but so are two of the SYSfans (I am able to control them through speedfan). I find it extremely hard to believe that the two other ones are for 'monitoring' only. You're telling me that they have 3 pins, two for voltage and one for monitoring, but they can't alter the voltage at all, so you'd have to put a controller between the pins and the fan? That completely erases the purpose of having the power coming from the motherboard. You could just get a fan controller that does the same thing, without having to screw around with the motherboard at all. Plus, speedfan doesn't even notice the PWM coming from either SYSFAN3 or SYSFAN4, if they are used for monitoring.
    This is the motherboard you're talking about, right? SYSFAN headers in red, and CPU in green.

  • The Power Supply Fan is still working, but does not appear to respond to increased loads, and its speed cannot be increased using SMCFanControl. Any suggestions?

    Hi all - My mac pro 1,1 has an enigmatic problem. It's quad-core, 3Ghz, running OS X 10.7.5. The problem began some months back, when running HD video conferences, HD streaming videos and some other graphics-moderate (I won't say intense) uses, such as slide shows in Just Looking. My machine has an ATY, RadeonX1900 card and 2 monitors - both Apple displays, one being 30 inch 2560x1600, the other being 24 inch 1920x1200.
    When I start those types of graphics-moderate apps, after about 5 minutes, something would crash (the monitors making a noise as it did) and the displays would both go black. The power did not appear to be fully cut off from the monitors. I think that the underlying applications, however, did not crash. So, I could still hear and speak to people during video conferences, and I could hear the sound tracks of videos.
    Attempts to restart the computer and get the monitors back did not immediately work to undo the problem, if done straight away. The only way to correct the problem (so as to have the monitors work) was to wait for a few minutes and then restart.
    After a lot of puzzled looking at console logs (and I confess that I am not an expert), I ran into a blank.
    But, because of the timing of the crashes (after ~5minutes use) and restarts (after some minutes wait), I reasoned that the problem might be temperature related.
    Once on that path of thought, I found this article:
    http://worldtv.com/blog/guides_tutorials/fixing_an_overheating_mac_pro_no_expens e_required.php
    I installed both Temperature Monitor and SMCFanControl. And I experimented, and got interesting results:
    Now to the puzzling bit: SMCFanControl shows that the speed of the Power Supply Fan doesn't vary much, even if I use SMCFanControl to ramp fan speeds right up. All of the other fans react to SMCFanControl, going up to and above 2500rpm when commanded. But the Power Supply Fan does not.  Having watched it for a few days now, the Power Supply Fan, according to AFCFanControl, never varies outside of a range from about 600-640 rpm, regardless of what I do with AFCFanControl.
    Also (and not surprisingly), whenever the graphics-moderate apps run, when I ramp all the fan speeds up using SMCFanControl, Temperature Monitor shows that the all of the temperatures within the machine plummet, except in the power supply locations. Power Supply Location 2 is the worst affected. Because the Power Supply Fan does not react as the other fans do, the "crashes" still occur.
    I could post some screen shots of the read outs of SMCFanControl and Temperature Monitor, although I think I have covered the key points in this post.
    It seems that the Power Supply Fan is still working, but does not respond to increased loads.
    Instinctively, I'm worried that if that's right, it might be a hard problem to fix. Any suggestions? Help! I would really appreciate them!
    Cheers
    P

    Thanks for your response Grant. I had already read about, and I think excluded, dust in graphics card/fan/assembly as a cause. The entire inside of the computer, including the graphics card/fan/assembly, is as clean as a whistle. It looks clean. I've cleaned the dust out every now and then (including a few days ago). Also, my undersanding (derived from the article, linked in my first post) is that I might expect to see high temperatures in the Northbridge and memory module B if the graphics card was overheating. According to Temperature Monitor, however, locations do not increase in temperature when I run the relevant apps. Finally, the graphics card/assembly does not feel too hot to touch.
    It is strange that SMCFanControl lists the Power Supply Fan as being software controllable, if that fan is not. Still, your comments are consistent with my observations, as the fan simply does not respond to software control.
    There are two upsides: First, I've something of a work-around. I've worked out what temperature must be achieved in Power Supply Location 2 for a crash to occur, and I can watch that location in Temperature Monitor, terminating the process before that treshold is reached. Of course, that's not ideal. Second, ramping all the other fans up does significantly delay the onset of the problem, and makes recovery time much quicker.
    Is there any donwside to peridically ramping up the other fans when running the relevant apps? Given that it causes all of the other locations to cool significantly, could this lessesn the life expecancy of the mahcine? (I don't want to run the fans up all the time - that's like sitting next to a jet ready for take off!)
    Also, a correction to my first post: Yesterday, with all the other fans running on full and running an HD streaming video, the Power Supply Fan did, eventually, slowly, come up to ~740rpm, which is much higher than the ~640rpm maximum I had previously seen, and this may have aided delaying the onset of the problem. 
    I'm not sure where this leaves me? The problem might now be able managed. Well, sort-of. But it's not eliminated.

  • Fan control questions

    Hi
    I have a mid 2008 2.8Ghz iMac with the stock 320 Gb HD and 4 Gb ram. It runs fine but I am worried about how hot the case gets at times, in particular the top left corner. I have iStat widget installed too which shows what I think are reasonable temps most of the time, but sometimes even after just everyday use (browsing etc...) some of the temps seem high (power supply is presently at 75c). The fan speeds don't seem to increase much at all from the factory minimums. I know about smc fan control and iMac fan control, but I have a couple of questions before I decide to use them.
    1. Do you think I need to be worried about this?
    2. What damage could I cause by running the fans harder?
    3. If I use these utilities to push the fans harder than Apple recommends, will I void my Apple Care?
    Looking forward to your answers
    Paul

    An utility like smcFanControl only changes the minimum fan speed setting. You are still running the fans well below its maximum capability. So the change is to the low end of the speed range, not the high end. You CAN set it high enough so that the minimum fan speed sounds like a small vacuum cleaner, but I would not set it that way for any length of time. I just tried it once to see what it sounded like with the fans running at a high speed (never heard them before). There is a max possible setting, so you can't set it to a crazy high number.
    I use smcFanControl and have the fans set about 25% higher than the default speed. I still can't even hear them at that setting, so I figured I wasn't doing any harm and it may help my iMac run cooler (not that noticed any issues with heat).
    I can't see how it would void AppleCare. Unless you set it to sound like a vacuum cleaner all the time (which would be really annoying), you are running the fans well within their normal operating range.
    Note: The adjusted minimum fan speed is only in effect while smcFanControl is running in the background. It does not change any system or hardware settings. To go back to the default settings, just quit smcFanControl.

  • P35 Neo - Sys Fan control

    I have a P35 Neo and recently i bought a cooler and a fan for my Ati4850.I connected the fan to the Sys Fan 1 but to my dissapointment i cant control the rpm of the fan through the Dual core center .
    I took a look at Bios but i couldnt find anything useful.
    Do i miss something ?
    I even download Speedfan but didnt help .

     I don't know of any that would have fan speed control for anything other than CPU fan. The only thing I can suggest would be to purchase a fan control module of some kind that goes in an empty drive bay. Something like >> this <<

Maybe you are looking for