Gx630 and problem with dvd playback via hdmi to plasma

I'm having problems playing a dvd from the gx630 while connected via HDMI to my plasma.  Without fail, the screen freezes up within 5 minutes of watching the movie.  I can watch a dvd on my laptop without a problem.  Any suggestions?

For what it's worth, I experienced the same thing recently with my GX630 while connected to a 42-inch Sharp Aquos. I tried a couple of different discs, but all of them froze just as you described and I had to reboot. I read somewhere that you have to "turn off" the laptop screen when doing this because of dvd copying restrictions, but I haven't looked into it any further.

Similar Messages

  • Problems with DVD playback.

    I created a DVD project in Encore, nothing fancy, just one video/audio track with a menu and a submenu.  When previewed, everything works great.  The burn completes with no problems, but the DVD gets choppy and stops playing at around 75 minutes.  I've tried multiple burns and tested the DVDs in multiple players.  Each has the same problem at the same point.  I've done many projects very similar to this one, and never had a problem.  Any ideas?

    PAllgeier wrote:
    I created a DVD project in Encore, nothing fancy, just one video/audio track with a menu and a submenu.  When previewed, everything works great.  The burn completes with no problems, but the DVD gets choppy and stops playing at around 75 minutes.  I've tried multiple burns and tested the DVDs in multiple players.  Each has the same problem at the same point.  I've done many projects very similar to this one, and never had a problem.  Any ideas?
    First thing to look at, as suggested above, is the burner or the media - but to confirm this, try compiling to a DVD folder & previewing in software first.
    If folder playback is fine then it is down to the burner or the media.
    When burning, follow a few simple rules and you will be okay most of the time:
    1 - Compile to an ISO image in Encore & burn using IMGBurn.
    2 - When loading image in IMGBurn, set burn speed to the slowest figure given - this is the optimal speed for your burner/media combination.
    3 - If this still fails, try changing media brand. Recommended are Verbatim Advanced Metal Azo type, or Taiyo Yuden if you can find any, or Falcon media. Avoid rubbish like Memorex and the unbranded ones especially. If a good quality media at a slow speed still fails, try changing the burner.
    Hope some of this helps

  • Just downloaded iOS6 onto my iphone4 and now my playback repeatedly cuts out after a few seconds--a particular problem with podcast playback. Anyone else out there have this problem??

    Just downloaded iOS6 onto my iphone4 and now my playback repeatedly cuts out after a few seconds--a particular problem with podcast playback. Anyone else out there have this problem??

    bump

  • Has anybody had problems with DVD's burnt with Optiarc drive

    I am burning movie DVD's through iDVD. The movie formats are initially QT with PCM sound encoding. They seem to work well on an old Samsung DVD player, but stutter on a brand new Samsung computer. I do understand it could be a problem with the newer computer, but I would like to hear if anyone else has had any problems so I can see if the problem is more widespread.
    OPTIARC DVD RW AD-5630A:
    Late 2007 20 inch Alloy iMac
    Model: OPTIARC DVD RW AD-5630A
    Revision: 1AHM
    Serial Number:
    Detachable Drive: No
    Protocol: ATAPI
    Unit Number: 0
    Socket Type: Internal
    Low Power Polling: Yes
    Any help appreciated
    Cheers
    Mick

    I too am having trouble playing DVDs burned with my Optiarc drive. Sorry I don't have the solution, but I can add a data point to the story about problems with DVDs burned with Optiarc.
    My current hardware: mid-2007 24" iMac, built-in Optiarc DVD RW AD-5630A with firmware 1AHM / MMC-3.
    My scenario: after making home movies with iMovie '08 and iDVD '08, I either burn to DVD (TDK 16x DVD-R 4.7 GB) straight from iDVD or I save as disc image from iDVD and then burn the disc image from Toast 9. In either scenario, I can play the DVD on my iMac or any other Mac or Windows computer. However, it will not play on my Xbox (original Xbox, not the 360) because it freezes when trying to mount (sometimes the Xbox will not recognize the disc as a DVD, and sometimes it will begin mounting the disc and then freeze before displaying the title menu).
    Before I bought my new iMac, I had the same workflow on an older 2003 17" G4 iMac that has a Sony DVD burner, and those discs play fine on all DVD players including my Xbox. To test the hypothesis that something happened to my Xbox around the time that I upgraded to my mid-2007 24" iMac, I burned several DVDs using my older iMac, and they continue to mount and play fine on the Xbox. On both my older and newer iMac, I have Mac OS X 10.5 Leopard installed, same version of Toast 9, and I burn at the slowest speed (2x) on both. So it seems that the problem can be isolated to the Optiarc DVD burner, but I'm not sure if there are other factors at play here.
    I searched the Optiarc site (www.sonynec-optiarc.com) but could not find a firmware update for the AD-5630A. However, I did find this site via Google:
    Liggy's and Dee's modified NEC and Optiarc firmwares
    http://liggydee.cdfreaks.com/page/en/Optiarc-AD-5630A/
    Because I was not sure about the site's reputation or validity of the firmware, I have not tried it yet.

  • Problems with DVD Player 3.0.1 in G4/466

    Problems with DVD Player in G4/466
    Yes, I've a g4/466 with two disks. In the first there's system 9.2.2 and the DVD player goes perfect. In the second I've system 10.2 and the 9.2, and the DVD Player (3.0.1) on the system 10 begins to jump in the dock, but stop and nothing happens, I can't open it...
    There's any way to reinstal it form system disks???
    Or any download to check the error?
    Thanks

    1. Try using Pacifist to extract it from your Mac OS X 10.2 installation disks, and then run the combo updater for your version of Mac OS X and any applicable DVD Player updates.
    2. Open the Console application in the /Applications/Utilities/ folder and look for lines relating to the DVD Player.
    (18543)

  • Problem with complete task via email

    Hello,
    I have problem with complete task via email. I found this blog very useful (http://blogs.adobe.com/ADEP/2010/11/how-to-complete-a-task-via-email-using-reply-to-comple te.html), but...
    I set up everything as it’s written in blog mentioned above. When a task is assigned to me, I received an email notification with actions (accept, deny). After that I replied with action “accept”. Then I received email with subject “Errors from LiveCycle ES”:
    LiveCycle ES has tried to process your request and encountered the following error:
    com.adobe.pof.POFRuntimeException: Transaction is not active: tx=TransactionImple ; – nested throwable: (javax.resource.ResourceException: Transaction is not active: tx=TransactionImple )
    This response to your original email
    Subject:RE:Task Assignment – Process: Test/Email_Test. Task 76 has been assigned to you.
    Date Sent:Thursday, October 24, 2011 1:17 PM
    Body:accept
    DO-NOT-DELETE: MTMhMzE0ITMyOA==!
    Attachments:
    In log appeared this following error:
    Caused by: ALC-DSC-215-000: com.adobe.idp.dsc.DSCRuntimeException: None of the Auth Provider could authenticate the user. Authentication Failed
    at com.adobe.livecycle.notification.TaskNotificationServiceImpl.processEmailComplete(TaskNot ificationServiceImpl.java:1157)
    Can you me please? I have no idea what to do to succesfully complete task via email endpoint. Thanks
    Jan Petrla

    Hi Diana, thanks for your reply.
    You're probably right about 2 different error messages.
    To the 1st one: I'm sure that status task is Assigned (to me). I received an email and I also reply on that email.
    To error log: I found out that error log appears when I enable email endpoint on Complete Task service. But I managed to solve this problem. I set wrong user. Now I have here the same user as is written in login-config.xml so log seems to be ok.
    So I created new task and tried to complete it via email. Now I receive email with another error:
    LiveCycle ES has tried to process your request and encountered the following error:
    com.adobe.idp.dsc.provider.service.email.impl.EmailProviderException: Error getting user context
    This response to your original email
    Subject:RE:Task Assignment - Process: WorkFlowClient/Test. Task 92 has been assigned to you.
    Date Sent:Thursday, October 27, 2011 3:05 PM
    Body:Complete
    DO-NOT-DELETE: MTIxMSExNjAzITIwMTE=!
    Attachments:
    And to the last point: email endpoint is set up with TestPOP3@mydomain and user receiving email has jpetrla@mydomain. I use Lotus Notes as email client, I tried another account with gmail, but the result was same.
    Now I really don't know to do...
    Jan

  • Problem with video playback with iTunes

    Several problems :
    Problem with video playback with iTunes -
    Since about a week, When I launch a video, it takes a long time to get started, then only the sound starts with no pictures - If I press pause then play the video is played normally. Did anyone face or heard about same kind of issue .
    Problem with permission disk errors
    After re-installing White Tiger and After I installed the last OSX 10.6.5 update
    I found the following problem
    Group differs on "Applications / Utilities / AirPort Utility.app / Contents / Resources / wanArrow.png", should be 0 instead of 80.
    Last but not least :
    My computer seems slow - I have 60gig free on My hard drive and I test my hard drive and everything seems all good .

    What was the fix for this? Everything has sucked for my itunes video playback since the last major revision release.

  • Problem with DVD Player

    I inherited this computer and have spent the last couple of months upgrading it. Put a gig of ram in and added a PCI card to help with a multi screen setup but now I have hit my first major head ache. I bought a Pioneer DVR - 104 off of ebay and installed it no problem. The only issue is once I went to test out my dvd feature I found I had no DVD player. I tried updating the system but it would not install it. So I finally was able to get 3.1 off of this site and it won't start up. It just blinks on the dock once and dissapears. I checked the specs and this machine came with the superdrive but my father opted out of it, why I don't know, so there should be no issues with the hardware, can anyone help me on this?
    867 mhz G4   Mac OS X (10.3.9)   1.25 GB RAM, 60 GB HD, 3 Monitor Display

    Hi-
    I'm sorry the extras is in OS 10.4- my mistake. In OS 10.3, I believe the DVD player is in the main package. I couldn't find it to install seperately. So.......
    Let me recap-
    1- The DVR reads install discs
    2- DVD's won't play because DVD player does not run
    3- DVD-R discs show no response
    So-
    1- The DVR is reading
    2- The version of DVD player may not be compatible
    3- There is no burn support
    To check burn support, in System Profiler, check if under Burn Support "Yes" is showing.
    My current thinking is, that since there was no DVR in the origional configuration, you may need to reinstall (Archive and install) the OS 10.3 to get the proper DVD player installed. this should also configure burn support.
    The other way to get burn support is to use the patchburn that I gave you the link to.
    BUT, I think you should do things one at a time. My advice is to first get the DVR to read, play and burn in that order. There is obviously a problem with DVD player, so, unless some else can advise differently, I would try the Archive and Install of the OS 10.3.
    It may also be good to run the OS 10.3.9 Combined Update:
    http://www.apple.com/support/downloads/macosxcombinedupdate1039.html
    trying the combined update now wouldn't hurt. If it does not remedy the situation, try the Archive and Install, then update.
    Best-
    Chris
    G4 AGP(450)Sawtooth   Mac OS X (10.4.8)   2ghzPPC,1.62gbSDRAM, ATI9800, DVR-110D,(IntHD)120&160,LaCie160,23"Cinema Display

  • How do I connect my new (purchased last week) macbook air to my samsung smart tv? I purchased the adapter at the apple store and connected to the TV via HDMI cable.  The TV says "no signal.  I do not see TV as an option in the display tab of system prefer

    how do I connect my new (purchased last week) macbook air to my samsung smart tv? I purchased the adapter at the apple store and connected to the TV via HDMI cable.  The TV says "no signal.  I do not see TV as an option in the display tab of system preferences.  what else do I need to do?

    First, make sure your TV is tuned to display the correct input signal. Most TVs have several inputs (multiple HDMIs, cable connections, RCA etc) so double-check that you're using the correct one - HDMI1, HDMI2 or whatever is written next to the port.
    I assume that you have a mini-Displayport to HDMI adaptor? If you open displays preferences, first tick the box that says "show display preferences in menu bar" then locate the menu and click Detect Displays. See if that helps.
    Matt

  • Any new  about updating lion to 10.7.4 and problems  with bluetooth devices  like Bose Soundlink Bluetooth Speaker?

    Any new  about updating lion to 10.7.4 and problems  with bluetooth devices  like Bose Soundlink Bluetooth Speaker?

    Monroe
    Just in the moment i updated to lion 10.7.4  my Bose Soundlink Bluetooth  stop working as  good as it was. I´m gonna try the update in the Bose  web page. I hope  it works

  • Problems with dvd and mac

    When I burn song on to a dvd or cd on computer ( mac intel) cannot play on cd player only on computer.
    Is there any way i can play on cd player?

    If AHT detects no errors with RAM, try Rember.
    One of my Macs was having problems and AHT was not able to detect any problems with RAM. As soon as I tried Rember, it was able to show me the error right away.
    Allan

  • Email problems with BB synched via BES. No email notifications and can't send replies.

    This isn't a question, but more of a public service announcement for those like myself that manage to screw up their email settings. I recently had problems with my email in that I would not get audible or visual notifications of new email and I couldn't send replies although I could forward and create new emails. The problem is that I am using Desktop Manager on two PCs and only one is configured to access my corporate email account, the one that is redirected to the BB. The default settings of my Desktop Manager installation was to synchronize the device date and time automatically when connected to the PC. Connecting my BB to my home machine would cause the email problems. I had to wipe and reactivate to fix my problems.
    So, if you want to use the BB on two PCs and one is not configured for the email account going to the phone... disable the auto synchronization option BEFORE connecting the device to that machine and launching Desktop Manager. It would also be nice if the Desktop Manager installer had an option to install on a PC that is used for backup/recovery and application loading only. The installer had two options IIRC and your choice was that the BB is used with BES or with a personal email account.

    Internally, your invites are processed by the server.
    If an outside sends a new invite to you, the server doesn't know about it until you add the event to your calendar app.
    You'll find settings in Mail and Calendar apps (depending on client OS) to automatically add invites to the Calendar.
    So to sum it up.
    Internal users, processed in real-time directly by the server
    External invites, must be processed by the client app, and depending on OS/Settings, could require manually adding or acknowleding. Also.. in 10.7/10.8 you will see an inbox tray in the Calendar app, your invites may show up there (and you'll need to click to ack)
    Hope that helps.

  • Problems with FCP playback on external LG monitor

    I have just purchased an LG 22EA63 external monitor to use with FCP 7. Monitor connects fine, works ok with other programmes but once in FCP , when i transfer both canvas and viewer windows onto the monitor, playback in not smooth with flickering streaks as if the footage is interlaced (even though my current project only has progressive footage). However it gets even worse with other FCP projects that contain interlaced footage - playback on canvas is even more jerky and streaky, and the viewer window is unable to play back most alterations made to clips (especially anyhting to do with motion or speed), making clips  jaggered and unwatchable.
    Any ideas what the problem is? I'm assuming it is to do with the LG screens' native resolution which is 1080p , but that doesn't explain why it is failing to play progressive clips at full quality.. Also I couldn't find another resolution setting that worked.
    I am connecting via HDMI to a MacBook Pro (2.8ghz Intel Core Duo, NVIDIA GeForce 9400M, native screen res: 1440x900).
    Obviously if I cant fix this I'll have to take the monitor back, any ideas or advice would be much appreciated.
    Thank you!

    I guess it's more accurate to say that there is a dramatic delay in the video between what I'm seeing in the playback window on my computer monitor and what I'm seeing on the external NTSC monitor. The audio does not have that delay, so on the external monitor the audio and video are out of sync. It makes it difficult to show anyone what you're working on, which is what the "client" monitor is supposed to do.

  • Using Qosmio G40 as HD-DVD player via HDMI to TV - possible?

    Is it possible to use G40 as HD-DVD player connecting it via HDMI interface to TV (Loewe Individual)?
    Have tried, however starting HD-DVD player, error message stating, can't use the interface.

    Yes, this is possible. I am using my G40 that way for several month now on my Pioneer plasma screen.
    When I want to play a DVD I do the following:
    1. Connect the laptop to the TV with a HDMI cable
    2. Turn the laptop and the TV on
    3. On your TV choose the right input-source
    3. On the laptop change the audio output tot HDMI
    4. If your TV doesn't have dolby-, dts- or wma-decoders on board, then turn dolby, dts and wma on the laptop off at the HDMI-settings (or else you will hear only a ticking sound)
    5. On the laptop press Fn+F5. Best you choose the video-output to only the TV. You should now see your laptop-screen on the TV-screen
    6. Start Windows Media Center on your laptop (I don't use the stand alone Toshiba HD DVD player because sometimes it gives me problems). You should hear the starting sound of Windows Media Center on your TV
    7. Load the DVD in the your laptops DVD-drive
    8. On Windows Media center choose play a DVD
    9. Enjoy the movie on your TV screen
    10. You can use your Windows Media Center Remote control to operate the DVD at the laptop. On my configuration I can also use the volume-controle of the Remote control to change the sound-level of the HDMI-oputput
    Later on - if you are ready with looking at the movie - don't forget to change the audio-output from HDMI to speakers or you will hear no sound on your laptop.
    Success!

  • CS4 Design Premium Installation Problem with DVDs

    Hey,
    I just bought the student Edition of the CS4 Desgin premium package.
    Have Windows XP SP3
    Anyway I put in the first DVD...and it loads...and loads....and loads...like half an hour.
    Nothing...cant open via explorer as well.
    So I restart with Dvd in the drive. restart took a bit longer but now I can acces via explorer.
    I start installation...works fine...put in Dvd2...works fine...Put in dvd3...loads...loads....loads...
    just for fun I put in dvd"Content"....loads...loads....loads.
    Ok so now I'm right in the middle of the installation...so cant just restart
    (I did try later after aborting Installation: then I can read em like dvd1)
    Now I have just installed half....with conent of dvd3-"content" missing
    I tested 25 other dvds I had laying around...all starting within the sec I entered em, so dvd drive seems fine.
    Cant remember how see specs at moment...but lets just say I can play "Crysis" on High smoothly
    It would maybe work if I could somehow install the content of dvd3 and dvd"Content" seperatley?
    (do I need dvd "content"?)
    Or how about If i create images of em and then mount em...think that would work (know a good free program?)?
    would appreciate some help
    VectorCookie

    I strongly suspect a bad production run of Adobe DVDs - I had enormous problems (see previous thread somewhere in this forum) attempting to install my Student Version Design Premium from the DVDs which Adobe sent me.  I then had absolutely no help from their telephone support.  I then had similarly no help from their online support portal - and, in fact, got really mad at them about it all.  I spent days trying to sort it out.  This message board - and one guru in particular - was very supportive and patient.
    My solution: I downloaded the trial version of the Creative Suite I had bought, installed from that (fast, easy, no problems at all) and then used the product key from the DVDs I had bought direct from Adobe.  So, I had to spend three days downloading (very slow broadband here) but it did, at least, get me a working copy.
    I wish Adobe would own up to sending out duff DVDs - but when I asked them (about the second question I asked in my first phone call) I was told that it was so unlikely that she (tech support woman) wanted me to try (all manner of ridiculous) other things first.
    Sarah

Maybe you are looking for