Handling Adapter Errors

I have a BPM that receives Soap messages sends a synchronous response then sends them to an R3 system.  Inside the BPM, around the send step I have a block with an Exception handler to catch any errors that are generated by the call so that I can retry sending the message. 
However, when an error occurs, eg the R3 system is taken down for maintenance, I get an XI error which does not get thrown back to the BPM exception handler.
Has anyone else got this to work or have any suggestions?
Thanks
Ian

Hi Ian,
You can set the Integration Server to automatically retry any deliver any messages failed due to a comms issue. In the Integration Server administration SXMB_ADM, run the option for Integration Engine configuration.
In here, click on <b>Specific Configuration</b>. Add an entry for category TUNING parameter IS_RETRY_LIMIT with a value of say 25.
This will force the Integration Engine to attempt 25 retries for delivery.
This retry interval is 2 minutes and is not changeable.
The message will be displayed in SXMB_MONI with a different icon instead of a red flag.
Does this help at all ?
Cheers
Colin.

Similar Messages

  • [Create Login] Provisioning Error: event handler/adapter could not be found

    Hello,
    I am running a fresh install of OIM 9.0.3 (installed yesterday) on a Windows XP Machine running:
    Weblogic 813 SP6
    JDK142 11,
    MSSQL 2000 SP3a I have a test resource, a simple MSSQL Table with a few fields, which I used the connector pack to install and connect. I imported the resource without any issues. However, when I attempt to Create Login on the resource, it gives me the following error:
    "An error occurred while retrying one of the tasks
    Create Login: Event Handler not found"When I check the details of Create Login (in my To-Do List for xelsysadm):
    Error Details
    The class file for event handler/adapter "adpDBCREATELOGIN" could not be found.I am very new to this system, and I really don't know where to begin trouble shooting this issue. Any ideas on what might be wrong with the system? It could be anywhere from missing a step in the beginning of the installation to doing something incorrectly. Any pointers on where I can start troubleshooting as to why I can't provision would be very helpful and much appreciated!
    Thanks

    Did you compile the adapters? When you import them from XML they must be compiled before you can use them. Go to the Design Console -> Dev tools -> Adapter Manager and compile them there.

  • Handling JDBC adapter errors in BPM

    Hi,
    I am using BPM to insert data in SQL server using a snychronous send.However i am not able to trap the adapter errors like server is down or could not insert because of key violation.
    Hence i decided to use transport level ack. But i understand that error description is returned in fault messages. Can i use fault messages in BPM???
    And also if that is not possible, I would like to know how can i configure alerts in JDBC adapter.
    Thanks in advance.

    Anand,
    I dont think this is possible. Fault Messages should be sent by the Application System back to XI , the Database in our case. AFAIK< the database cannot send back such fault messages and the error message is trapped in the JDBC adapters log. Try using Adapter Engine Alerts and this will cause the Message to be passed to your ALert framework from the adapter.
    Regards,
    Bhavesh

  • Unable to create database due to ORA-12560, TNS protocol adapter error

    Hello,
    I'm trying to create an 8.1.7.0 database on a W2k server, but it is failing because as soon as svrmgrl is launched, I get an ORA-12560, TNS: protocol adapter error:
    D:\oracle\db_creation_scripts>D:\oracle\ora81\bin\svrmgrl @D:\oracle\db_creation_scripts\mterm62run.sql
    Oracle Server Manager Release 3.1.7.0.0 - Production
    Copyright (c) 1997, 1999, Oracle Corporation. All Rights Reserved.
    ORA-12560: TNS:protocol adapter errorEcho ON
    SVRMGR> connect INTERNAL/manager
    ORA-12560: TNS:protocol adapter error
    SVRMGR> startup nomount pfile="D:\oracle\admin\mterm62\pfile\initmterm62.ora"
    LCC-00161: Message 161 not found; product=RDBMS; facility=MGR
    My ORACLE_HOME, ORACLE_SID, and TNS_ADMIN environmental variables are correctly set, and I'm able to tnsping the listener.
    I've enabled tracing, and my client trace file is:
    --- TRACE CONFIGURATION INFORMATION FOLLOWS ---
    New trace stream is d:\trace\client_trace.log_2084_9.trc
    New trace level is 6
    --- TRACE CONFIGURATION INFORMATION ENDS ---
    --- PARAMETER SOURCE INFORMATION FOLLOWS ---
    Attempted load of system pfile source d:\oracle\ora81\network\admin\sqlnet.ora
    Parameter source loaded successfully
    Attempted load of local pfile source D:\oracle\db_creation_scripts\sqlnet.ora
    Parameter source was not loaded
    -> PARAMETER TABLE LOAD RESULTS FOLLOW <-
    Successful parameter table load
    -> PARAMETER TABLE HAS THE FOLLOWING CONTENTS <-
    TRACE_DIRECTORY_SERVER = d:\trace
    TRACE_DIRECTORY_CLIENT = d:\trace
    NAMES.DIRECTORY_PATH = (TNSNAMES, HOSTNAME)
    SQLNET.CRYPTO_SEED = 4fhfguweotcadsfdsafjkdsfqp5f201p45mxskdlfdasf
    TRACE_FILE_CLIENT = client_trace.log
    TRACE_FILE_SERVER = server_trace.log
    SQLNET.AUTHENTICATION_SERVICES = (NTS)
    TRACE_UNIQUE_CLIENT = on
    TRACE_LEVEL_CLIENT = ADMIN
    TRACE_LEVEL_SERVER = ADMIN
    --- PARAMETER SOURCE INFORMATION ENDS ---
    --- LOG CONFIGURATION INFORMATION FOLLOWS ---
    Log stream will be "D:\oracle\db_creation_scripts\sqlnet.log"
    Log stream validation not requested
    --- LOG CONFIGURATION INFORMATION ENDS ---
    nigini: entry
    nigini: Count in NI global area now: 1
    nigini: Count in NI global area now: 1
    nrigbi: entry
    nrigbni: entry
    nrigbni: Unable to get data from navigation file tnsnav.ora
    nrigbni: exit
    nrigbi: exit
    nigini: exit
    niqname: Hst is already an NVstring.
    niqname: Inserting CID.
    niotns: entry
    niotns: niotns: setting up interrupt handler...
    niotns: Not trying to enable dead connection detection.
    niotns: Calling address: (DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=BEQ)(PROGRAM=oracle)(ARGV0=oracleMTERM62)(ARGS='(DESCRIPTION=(LOCAL=YES)(ADDRESS=(PROTOCOL=beq)))')))(CONNECT_DATA=(SID=MTERM62)(CID=(PROGRAM=D:\oracle\ora81\bin\SVRMGRL.EXE)(HOST=SERV0354)(USER=tarisa))))
    nsmal: 140 bytes at 0x12493f0
    nscall: connecting...
    nladini: entry
    nladini: exit
    nladget: entry
    nladget: exit
    nlpcaini: entry
    nlpcaini: prg =
    nlpcaini: arg[0] =
    nlpcaini: arg[1] =
    nlpcaini: exit
    nsmal: 420 bytes at 0x12542f0
    nsmal: 1712 bytes at 0x12572f0
    nsopen: opening transport...
    ntpcon: entry
    ntpcon: toc = 1
    sntpcall: entry
    snlpcss: entry
    ntpcon: exit
    nserror: nsres: id=0, op=65, ns=12560, ns2=0; nt[0]=530, nt[1]=2, nt[2]=0; ora[0]=0, ora[1]=0, ora[2]=0
    nsopen: unable to open transport
    nsmfr: 1712 bytes at 0x12572f0
    nsmfr: 420 bytes at 0x12542f0
    nladget: entry
    nladget: exit
    nsmfr: 140 bytes at 0x12493f0
    nladtrm: entry
    nladtrm: exit
    nioqper: error from nscall
    nioqper: nr err code: 0
    nioqper: ns main err code: 12560
    nioqper: ns (2) err code: 0
    nioqper: nt main err code: 530
    nioqper: nt (2) err code: 2
    nioqper: nt OS err code: 0
    niomapnserror: entry
    niqme: entry
    niqme: reporting NS-12560 error as ORA-12560
    niqme: exit
    niomapnserror: returning error 12560
    niomapnserror: exit
    niotns: Couldn't connect, returning 12560
    niotns: exit
    nigtrm: Count in the NI global area is now 0
    nnfgdei: entry
    nrigbd: entry
    nrigbd: exit
    nigtrm: Count in the NL global area is now 0
    My tnsnames, listener and sqlnet.ora files are very simple:
    ## BEGIN TNSNAMES.ORA
    # TNSNAMES.ORA Network Configuration File: D:\oracle\ora81\NETWORK\ADMIN\tnsnames.ora
    # Generated by Oracle configuration tools.
    MTERM62 =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = TCP)(HOST = 10.3.1.75)(PORT = 1521))
    (CONNECT_DATA =
    (SERVICE_NAME = mterm62)
    (INSTANCE_NAME = mterm62)
    INST1_HTTP =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = TCP)(HOST = 10.3.1.75)(PORT = 1521))
    (CONNECT_DATA =
    (SERVER = SHARED)
    (SERVICE_NAME = mterm62)
    (PRESENTATION = http://admin)
    # LISTENER.ORA Network Configuration File: D:\oracle\ora81\NETWORK\ADMIN\listener.ora
    # Generated by Oracle configuration tools.
    LISTENER =
    (DESCRIPTION =
    (ADDRESS = (PROTOCOL = TCP)(HOST = serv0354)(PORT = 1521))
    SID_LIST_LISTENER =
    (SID_DESC =
    (ORACLE_HOME = D:\oracle\ora81)
    (SID_NAME = mterm62)
    TRACE_LEVEL_LISTENER = ADMIN
    # SQLNET.ORA Network Configuration File: D:\oracle\ora81\NETWORK\ADMIN\sqlnet.ora
    # Generated by Oracle configuration tools.
    TRACE_DIRECTORY_CLIENT = d:\trace
    TRACE_UNIQUE_CLIENT = on
    TRACE_DIRECTORY_SERVER = d:\trace
    SQLNET.AUTHENTICATION_SERVICES= (NTS)
    TRACE_FILE_CLIENT = client_trace.log
    TRACE_FILE_SERVER = server_trace.log
    TRACE_LEVEL_CLIENT = ADMIN
    TRACE_LEVEL_SERVER = ADMIN
    NAMES.DIRECTORY_PATH= (TNSNAMES, HOSTNAME)
    SQLNET.CRYPTO_SEED = 4fhfguweotcadsfdsafjkdsfqp5f201p45mxskdlfdasf
    Does anyone have any ideas what else I can check. I'm a Unix person, not a Windows person, which is making it even more complicated. If I was on Unix, I'd just blow everything away and start again from scratch, but since I'm not sure how to remove all traces from the registry, etc., I don't want to try that on this machine. There was already one other database created, but it's not goign to be used.
    Any help would be greatly appreciated.
    regards,
    Tarisa.

    hi,
    thanks for the info. the problem, as it turns out, was that I was connected to the db server via a terminal service (Microsoft Management Console), which for some reason caused probelms with TNS. After I connected directly to the machine using VNC, I was able to create the database with no problems. strange but true.
    regards,
    Tarisa.

  • How to handle system errors in XI using BPM? please help!

    Hi Experts,
         I have a requirement where I have to handle system errors. For example when I am making RFC call using RFC adapter if the remote destination is down then I have create a understandable error message and store it in another SAP table.
    How to handle it? I am using BPM. I can see that there is "Exceptions" in the send step. How to use this?
    Thanks
    Gopal

    Hi Gopalkrishna,
    In this case whenever you get Mapping Exception , you can raise an Exception with the help of BPM and you can send the status to the RFC. But with the help of BPM.
    For a Simple case refer:
    http://help.sap.com/saphelp_nw2004s/helpdata/en/33/4a773f12f14a18e10000000a114084/frameset.htm
    If you want you can do it without a BPM
    and throw an exception in case any of the values is missing:
    have a look at this weblog on how to throw exceptions
    in a nice way:
    /people/alessandro.guarneri/blog/2006/01/26/throwing-smart-exceptions-in-xi-graphical-mapping
    Also just go through <a href="/people/sap.user72/blog/2005/02/23/raising-exceptions-in-sap-xi-mapping Exceptions in SAP XI Mapping</a> and see if it helps you solve the problem.
    Also go through these links:
    http://help.sap.com/saphelp_nw04/helpdata/en/dc/6b7f2243d711d1893e0000e8323c4f/content.htm
    http://help.sap.com/saphelp_nw04/helpdata/en/68/253239bd1fa74ee10000000a114084/content.htm
    http://help.sap.com/saphelp_nw04/helpdata/en/cf/f2bbc8142c11d3b93a0000e8353423/frameset.htm
    http://help.sap.com/saphelp_nw04/helpdata/en/5d/2166e6a91d11d188de0000e8216438/content.htm
    http://help.sap.com/saphelp_nw04/helpdata/en/05/bb223905b61b0ae10000000a11402f/content.htm
    Please do let know if it helped.
    Regards,
    Abhy

  • R12 Vision Install Fails, TNS-12560: TNS:protocol adapter error

    Below please find the NetServiceHandler.log from the install and an excerpt from ApplyDBTechStack...log
    OS: Windows Server 2003 SP2 x86
    I have installed the loopback adapter, modified the hosts file, and entered the DNS info. Not sure what else I can do.
    -----------begin NetServiceHandler.log-------------------------
         Classpath : ;D:\oracle\VIS\db\tech_st\11.1.0\jdbc\lib\ojdbc6.jar;D:\oracle\VIS\db\tech_st\11.1.0\appsutil\java\xmlparserv2.jar;D:\oracle\VIS\db\tech_st\11.1.0\appsutil\java;D:\oracle\VIS\db\tech_st\11.1.0\jlib\netcfg.jar;D:\oracle\VIS\db\tech_st\11.1.0\jlib\ldapjclnt11.jar
    ===============================================================================
    NetServiceHandler 120.19 started for oracleebs at Wed Jun 13 09:32:30 PDT 2012
    ===============================================================================
    [ Context Information ]
    Host : oracleebs
    Domain : demo.com
    Out Dir : D:\oracle\VIS\db\tech_st\11.1.0/appsutil/out/VIS_oracleebs/06130932
    Tier Type : DATABASE TIER
    Getting connection...
    ADX Database Utility
    getConnectionUsingAppsJDBCConnector() -->
    APPS_JDBC_URL='null'
    Trying to get connection using SID based connect descriptor
    getConnection() -->
    sDbHost : oracleebs
    sDbDomain : demo.com
    sDbPort : 1521
    sDbSid : VIS
    sDbUser : APPS
    Trying to connect using SID...
    getConnectionUsingSID() -->
    JDBC URL: jdbc:oracle:thin:@oracleebs.demo.com:1521:VIS
    Exception occurred: java.sql.SQLException: The Network Adapter could not establish the connection
    Trying to connect using SID as ServiceName
    getConnectionUsingServiceName() -->
    JDBC URL: jdbc:oracle:thin:@(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=oracleebs.demo.com)(PORT=1521))(CONNECT_DATA=(SERVICE_NAME=VIS)))
    Exception occurred: java.sql.SQLException: The Network Adapter could not establish the connection
    Trying to connect using SID as ServiceName.DomainName
    getConnectionUsingServiceName() -->
    JDBC URL: jdbc:oracle:thin:@(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=oracleebs.demo.com)(PORT=1521))(CONNECT_DATA=(SERVICE_NAME=VIS.demo.com)))
    Exception occurred: java.sql.SQLException: The Network Adapter could not establish the connection
    Connection could not be obtained; returning null
    -------------------ADX Database Utility Finished---------------
    Could not get connection to the database.
    Exiting with status 100 to instantiate the tnsnames.ora template
    Creation of Directory - D:\oracle\VIS\db\tech_st\11.1.0\NETWORK\ADMIN\VIS_oracleebs Succeeded.
    instantiate file:
    source : D:\oracle\VIS\db\tech_st\11.1.0\appsutil\template\ad8itns.ora
    dest : D:\oracle\VIS\db\tech_st\11.1.0\network\admin\VIS_oracleebs\tnsnames.ora
    AutoConfig is exiting with status 0
    instantiate file:
    source : D:\oracle\VIS\db\tech_st\11.1.0\appsutil\template\ad8ilsnr.ora
    dest : D:\oracle\VIS\db\tech_st\11.1.0\network\admin\VIS_oracleebs\listener.ora
    AutoConfig is exiting with status 0
    adgentns.pl exiting with status 0
    ERRORCODE = 0 ERRORCODE_END
    ----------------end NetServiceHandler.log------------------------
    -------------------begin excerpt ApplyDBTechStack...log--------------------
    SNRCTL for 32-bit Windows: Version 11.1.0.7.0 - Production on 13-JUN-2012 09:32:41
    Copyright (c) 1991, 2008, Oracle. All rights reserved.
    Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=oracleebs.demo.com)(PORT=1521)))
    TNS-12541: TNS:no listener
    TNS-12560: TNS:protocol adapter error
    TNS-00511: No listener
    32-bit Windows Error: 61: Unknown error
    LSNRCTL for 32-bit Windows: Version 11.1.0.7.0 - Production on 13-JUN-2012 09:32:43
    Copyright (c) 1991, 2008, Oracle. All rights reserved.
    Starting tnslsnr: please wait...
    Failed to open service <OracleTNSListenerVIS>, error 1060.
    TNSLSNR for 32-bit Windows: Version 11.1.0.7.0 - Production
    Message 459 not found; No message file for product=NETWORK, facility=NL
    Message 279 not found; No message file for product=NETWORK, facility=NL
    Message 1073 not found; No message file for product=NETWORK, facility=TNS
    Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=oracleebs.demo.com)(PORT=1521)))
    STATUS of the LISTENER
    Alias VIS
    Version TNSLSNR for 32-bit Windows: Version 11.1.0.7.0 - Production
    Start Date 13-JUN-2012 09:32:46
    Uptime 0 days 0 hr. 0 min. 2 sec
    Trace Level off
    Security ON: Local OS Authentication
    SNMP OFF
    Listener Parameter File D:\oracle\VIS\db\tech_st\11.1.0\network\admin\VIS_oracleebs\listener.ora
    Listener Log File D:\oracle\VIS\db\tech_st\11.1.0/network/admin\vis.log
    Listening Endpoints Summary...
    (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=10.0.0.68)(PORT=1521)))
    Services Summary...
    Service "VIS" has 1 instance(s).
    Instance "VIS", status UNKNOWN, has 1 handler(s) for this service...
    The command completed successfully
    addlnctl.cmd exiting with status 0
    OpenService failed
    adsvdlsn.cmd exiting with status 1007
    ERRORCODE = 1007 ERRORCODE_END
    .end std out.
    .end err out.
    -------------------end excerpt ApplyDBTechStack...log-------------------------

    Hi;
    Pelase check below notes which is mention same error message
    On Windows, After 10g Upgrade, Running Autoconfig on Apps Tier Failed with : Unable To Start Apps Services TNS-12224: TNS:no listener TNS-12541 TNS-12560: TNS:protocol adapter error TNS-00511: N .. [ID 577713.1]
    Windows Autoconifg on dbTier fails on adcrobj.cmd & adsvdlsn.cmd [ID 356927.1
    Rapid Clone on Windows Fails When SID Is Over 8 Characters: "Rc-00118: Error Occurred During Creation Of Database, Failed to open service" [ID 405688.1]
    Regard
    Helios

  • Sending Email When FTP Adapter Errors Out

    Hello everyone,
    I am developing a very simple interface to grab a file from a directory and ftp it to a partner's server. Now I want to be able to check if an error occurs when I send the file so I can send a notification e-mail to the administrator and move the file to an Error-Archive directory.
    Some of the errors that could happen are:
    1. Partner server is down
    2. FTP Username or password is wrong
    3. FTP account does not have permissions to write to the Partner server
    4. ...etc
    I have defined an Integration process and for the block where I ftp my file, I defined an exception which I catch in an exception branch. In the Exception branch, I have then defined steps to send notification emails and move the file to an error-archive directory. But unfortunately all the steps of the Integration Process seems to pass, although the FTP Adapter throughs an error.
    I'm not sure how can I get the FTP adapter errors to be passed back to my integration process. I already searched in the service market place for OSS notes and also searched the SDN but I can't find any helpful information.
    There is one OSS note, 821267, that mentions the use of System Acknowledgements. I'm not sure if this will help me and I don't know how to set it up.
    Does anyone have any ideas on how to handle this particular scenario? Did anyone implement System Acknowledgements with the File/FTP adapter?
    Any help is greatly appreciated

    Hi,
    To do the alert configuration as suggested, please go through the information below.
    From SP 14 on PMI-free alerting was introduced. That means before SP 14 one has to configure and activate the End-to-End Monitoring, and to schedule the report SXMSALERT_PROCESS_DATA_GET in order to extract the alerts from the PMI data. For SP 14 and higher, that's not longer necessary.
    If no alerts are being delivered, please check if "Suppress multiple alerts of this rule" is checked for your rule.
    For SP 14 and higher you could also have a look at the report sxmsalert_logreader. This report shows some information about alerts being created or not.
    You'll find more information about trouble shooting the alerting in SAP Note 913858.
    Also just check if this batch program (RSALERTPROC) is running or not.
    The links below on Alert Management (ALM) will be of good help to you:
    http://help.sap.com/saphelp_nw04/helpdata/en/3f/567ddea69d3d4c93a6aedabd08899e/frameset.htm
    http://help.sap.com/saphelp_nw04/helpdata/en/3f/81023cfa699508e10000000a11402f/frameset.htm
    Meanwhile look at these forum threads also:
    Alerts not getting triggered from Adapter Framework
    Alert  Configs...
    Also, In ALRTCATDEF, go to SETTINGS--> CONFIGURATION. By default, the option selected is INTERNAL PROCESSING. Select the option SMTP FORWARDING AS XML and give the email id. This will enable you to send an email alert whenever an error occurs in XI.
    I hope I have answered your queries. If u want help with anything else please do reply back.
    Regards,
    abhy
    PS: AWARD POINTS FOR HELPFUL ANSWERS.

  • TNS-12560: TNS:protocol adapter error listener not starting up.

    Hi all
    we came to an issue where we have to move our server from one data centre to another after unplugging the machine and re-plugging the server
    1) Operating system (OEL 5.1) started.
    2) Database 11gR2 started.
    3) Listener Failed to Start.
    [oracle@yam01 tmp]$ lsnrctl start lsn_yscc12
    LSNRCTL for Linux: Version 11.2.0.1.0 - Production on 02-OCT-2012 07:57:58
    Copyright (c) 1991, 2009, Oracle. All rights reserved.
    Starting /u01/app/oracle/product/11.2.0/bin/tnslsnr: please wait...
    TNS-12537: TNS:connection closed
    TNS-12560: TNS:protocol adapter error
    TNS-00507: Connection closed
    Linux Error: 29: Illegal seek
    [oracle@yam01 tmp]$
    When checked in sqlnet.log we found.
    [oracle@yam01 log]$ cat sqlnet.log
    Directory does not exist for read/write [u01/app/oracle/product/11.2.0/log] [u01/app/oracle/product/11.2.0/log/diag/clients]
    [oracle@yam01 log]$
    /u01/app/oracle/product/11.2.0/log
    /u01/app/oracle/product/11.2.0/log/diag/clients --> here under diag folder client folder was missing.
    drwxrwxr-x 3 oracle oinstall 4096 Sep 30 12:59 /u01/app/oracle/product/11.2.0/log/diag/
    *[oracle@yam01 log]$ cd /u01/app/oracle/product/11.2.0/log/diag/clients*
    -bash: cd: /u01/app/oracle/product/11.2.0/log/diag/clients: No such file or directory
    *[oracle@yam01 log]*
    [oracle@yam01 diag]$ mkdir clients
    [oracle@yam01 diag]$ ls -ltr
    total 12
    drwxr-x--- 3 oracle oinstall 4096 Sep 30 12:59 rdbms
    -rw-r----- 1 oracle oinstall 15 Oct 2 07:43 adrci_dir.mif
    drwxr-xr-x 2 oracle oinstall 4096 Oct 2 08:27 clients
    [oracle@yam01 diag]$
    and added *"SUBSCRIBE_FOR_NODE_DOWN_EVENT_lsn_yscc12=OFF"*
    and then when started all the listener it started successfully.+_
    [oracle@yam01 ~]$ lsnrctl status lsn_yscc12
    LSNRCTL for Linux: Version 11.2.0.1.0 - Production on 02-OCT-2012 08:40:19
    Copyright (c) 1991, 2009, Oracle. All rights reserved.
    Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=100.100.50.199)(PORT=1603)))
    STATUS of the LISTENER
    Alias lsn_yscc12
    Version TNSLSNR for Linux: Version 11.2.0.1.0 - Production
    Start Date 02-OCT-2012 08:28:09
    Uptime 0 days 0 hr. 12 min. 9 sec
    Trace Level admin
    Security ON: Local OS Authentication
    SNMP OFF
    Listener Parameter File /u01/app/oracle/product/11.2.0/network/admin/listener.ora
    Listener Log File /u01/app/oracle/diag/tnslsnr/yam01/lsn_yscc12/alert/log.xml
    Listener Trace File /u01/app/oracle/diag/tnslsnr/yam01/lsn_yscc12/trace/ora_10095_3086223040.trc
    Listening Endpoints Summary...
    (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=100.100.50.199)(PORT=1603)))
    Services Summary...
    Service "YSCC12.YAMAMACEMENT.COM" has 1 instance(s).
    Instance "yscc12", status UNKNOWN, has 1 handler(s) for this service...
    The command completed successfully
    [oracle@yam01 ~]$
    Thanks all for Reading this post
    hope if you came across this issues this may work for you.
    Best Regards
    Kaleem.

    Welcome to OTN
    Thank you For you sharing :)

  • TNS-12560: TNS:protocol adapter error  TNS-00530: Protocol adapter error

    Unable to start listener service.
    Running Oracle Database 11gr2 on Windows 7.
    I just installed Oracle with the "install software only" option.
    Already set up the instance, the database, the dictionary views, etc.
    Created tsnames.ora, sqlnet.ora and listener.ora as shown below.
    Before installing Oracle I followed the instruction on Oracle
    documentation to install a Loopback Adapter.
    It is set up as the primary adapter as indicated on the
    instructions. The name is "gabylan" (previously the computer
    name was "P4". I set up the "hosts" file as indicated, the oracle_hostname
    variable, etc. as you will see below. I don't know if it's important to "uncomment"
    the line on the "hosts" file for the "localhost" entry, I left it
    as it was originally.
    Services currently in "Started" Status:
    OracleServiceorcl
    Oracle orcl VSS Writer Service
    OracleMTSRecoveryService
    OracleOraDb11g_home1ClrAgent
    OracleServiceorcl
    Below is a summary of the error message and some information
    about my system setup to help you diagnose my problem.
    ===============================================================================
    c:\Users\Public\myscripts>lsnrctl start
    LSNRCTL for 32-bit Windows: Version 11.2.0.1.0 - Production on 18-SEP-2012 13:48
    Copyright (c) 1991, 2010, Oracle. All rights reserved.
    Starting tnslsnr: please wait...
    TNS-12560: TNS:protocol adapter error
    TNS-00530: Protocol adapter error
    c:\Users\Public\myscripts> lsnrctl status
    LSNRCTL for 32-bit Windows: Version 11.2.0.1.0 - Production on 18-SEP-2012 16:17:16
    Copyright (c) 1991, 2010, Oracle. All rights reserved.
    Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=gabylan)(PORT=1521)))
    TNS-12541: TNS:no listener
    TNS-12560: TNS:protocol adapter error
    TNS-00511: No listener
    32-bit Windows Error: 61: Unknown error
    ================================================================================
    My "hosts" File: (c:\windows\system32\drivers\etc\hosts)
    # localhost name resolution is handled within DNS itself.
    #     127.0.0.1 localhost
    #     ::1 localhost
    192.168.5.5          gabylan          gabylan
    =================================================================================
    c:\Users\Public\myscripts>ipconfig /all
    Windows IP Configuration
    Host Name . . . . . . . . . . . . : gabylan
    Primary Dns Suffix . . . . . . . :
    Node Type . . . . . . . . . . . . : Hybrid
    IP Routing Enabled. . . . . . . . : No
    WINS Proxy Enabled. . . . . . . . : No
    Ethernet adapter Local Area Connection 2:
    Connection-specific DNS Suffix . :
    Description . . . . . . . . . . . : Microsoft Loopback Adapter
    Physical Address. . . . . . . . . : 02-00-4C-4F-4F-50
    DHCP Enabled. . . . . . . . . . . : No
    Autoconfiguration Enabled . . . . : Yes
    Link-local IPv6 Address . . . . . : fe80::b8f5:bbb0:cf8b:c735%15(Preferred)
    IPv4 Address. . . . . . . . . . . : 192.168.5.5(Preferred)
    Subnet Mask . . . . . . . . . . . : 255.255.255.0
    Default Gateway . . . . . . . . . :
    DHCPv6 IAID . . . . . . . . . . . : 335675468
    DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-B7-78-52-00-25-22-51-68-AB
    DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1
    fec0:0:0:ffff::2%1
    fec0:0:0:ffff::3%1
    NetBIOS over Tcpip. . . . . . . . : Enabled
    Ethernet adapter Local Area Connection:
    Connection-specific DNS Suffix . :
    Description . . . . . . . . . . . : Realtek RTL8102E/RTL8103E Family PCI-E Fast Ethernet NIC (NDIS 6.20)
    Physical Address. . . . . . . . . : 00-25-22-51-68-AB
    DHCP Enabled. . . . . . . . . . . : Yes
    Autoconfiguration Enabled . . . . : Yes
    Link-local IPv6 Address . . . . . : fe80::7538:173c:c202:4985%10(Preferred)
    IPv4 Address. . . . . . . . . . . : 192.168.1.2(Preferred)
    Subnet Mask . . . . . . . . . . . : 255.255.255.0
    Lease Obtained. . . . . . . . . . : Tuesday, September 18, 2012 11:37:37 AM
    Lease Expires . . . . . . . . . . : Wednesday, September 19, 2012 1:45:01 PM
    Default Gateway . . . . . . . . . : 192.168.1.1
    DHCP Server . . . . . . . . . . . : 192.168.1.1
    DHCPv6 IAID . . . . . . . . . . . : 234890530
    DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-B7-78-52-00-25-22-51-68-AB
    DNS Servers . . . . . . . . . . . : 192.168.1.1
    NetBIOS over Tcpip. . . . . . . . : Enabled
    =================================================================================
    # sqlnet.ora Network Configuration File:
    # c:\app\oracle\product\11.2.0\dbhome_1\NETWORK\ADMIN\sqlnet.ora
    # This file is actually generated by netca. But if customers choose to
    # install "Software Only", this file wont exist and without the native
    # authentication, they will not be able to connect to the database on NT.
    # OTHER OPTION FOR AUTHENTICATION IS: SQLNET.AUTHENTICATION_SERVICES= (NTS)
    SQLNET.AUTHENTICATION_SERVICES= (NONE)
    NAMES.DIRECTORY_PATH= (TNSNAMES, HOSTNAME, EZCONNECT)
    ADR_BASE = c:\app\oracle\
    ====================================================================================
    # tnsnames.ora Network Configuration File:
    # c:\app\oracle\product\11.2.0\dbhome_1\NETWORK\ADMIN\tnsnames.ora
    orcl =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = TCP)(HOST = gabylan)(PORT = 1521))
    (CONNECT_DATA =
    (SERVER = DEDICATED)
    (SERVICE_NAME = orcl)
    ====================================================================================
    # listener.ora Network Configuration File:
    # c:\app\oracle\product\11.2.0\dbhome_1\network\admin\listener.ora
    LISTENER =
    (DESCRIPTION_LIST =
    (DESCRIPTION =
    (ADDRESS = (PROTOCOL = TCP)(HOST = gabylan)(PORT = 1521))
    SID_LIST_LISTENER =
         (SID_LIST =
              (SID_DESC =
         (ORACLE_HOME = c:\app\oracle\product\11.2.0\dbhome_1)
         (SID_NAME = orcl)
    ADR_BASE_LISTENER = c:\app\oracle
    =================================================================================
    c:\Users\Public\myscripts>ping gabylan
    Pinging gabylan [192.168.5.5] with 32 bytes of data:
    Reply from 192.168.5.5: bytes=32 time<1ms TTL=128
    Reply from 192.168.5.5: bytes=32 time<1ms TTL=128
    Reply from 192.168.5.5: bytes=32 time<1ms TTL=128
    Reply from 192.168.5.5: bytes=32 time<1ms TTL=128
    Ping statistics for 192.168.5.5:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
    Approximate round trip times in milli-seconds:
    Minimum = 0ms, Maximum = 0ms, Average = 0ms
    =================================================================================     
    Some related environment variables on my system:
    COMPUTERNAME=GABYLAN
    FP_NO_HOST_CHECK=NO
    HOMEPATH=\Users\oracle
    LOGONSERVER=\\GABYLAN
    ORACLE_HOME=c:\app\oracle\product\11.2.0\dbhome_1
    ORACLE_HOSTNAME=gabylan
    ORACLE_SID=orcl
    ORACLE_UNQNAME=orcl
    SQLPATH=c:\users\public\myscripts
    USERDOMAIN=GABYLAN
    USERNAME=oracle
    USERPROFILE=C:\Users\oracle
    ==================================================================================
    Summary from V$INSTANCE VIEW:
    INSTANCE
    NAME    HOSTNAME STARTUP_T STATUS DATABASE_STATUS ACTIVE_ST
    orcl GABYLAN STARTED      ACTIVE NORMAL
    =================================================================================
    Thanks,
    Gabriel

    I am getting the same error while starting or stopping the listener
    LSNRCTL> start CSCLIST
    Starting tnslsnr: please wait...
    TNS-12560: TNS:protocol adapter error
    TNS-00530: Protocol adapter error
    LSNRCTL> stop CSCLIST
    Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=CSCINDAE708070)(PORT=152
    2)))
    NL-00303: syntax error in NV string
    TNS-01153: Failed to process string: (DESCRIPTION=(CONNECT_DATA=(CID=(PROGRAM=)
    (HOST=)(USER=Manager(REMOVE)))(COMMAND=stop)(ARGUMENTS=64)(SERVICE=CSCLIST)(VERS
    ION=186646784)))
    Pls help
    Listener.ora:
    # listener.ora Network Configuration File: D:\Sagaya\11gDBhome\product\11.2.0\dbhome_1\network\admin\listener.ora
    # Generated by Oracle configuration tools.
    CSCLIST =
    (DESCRIPTION_LIST =
    (DESCRIPTION =
    (ADDRESS = (PROTOCOL = TCP)(HOST = CSCINDAE708070)(PORT = 1522))
    (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1522))
    SID_LIST_CSCLIST =
    (SID_LIST =
    (SID_DESC =
    (SID_NAME = CLRExtProc)
    (ORACLE_HOME = D:\Sagaya\11gDBhome\product\11.2.0\dbhome_1)
    (PROGRAM = extproc)
    (ENVS = "EXTPROC_DLLS=ONLY:D:\Sagaya\11gDBhome\product\11.2.0\dbhome_1\bin\oraclr11.dll")
    ADR_BASE_CSCLIST = D:\Sagaya\11gDBhome

  • TNS-12560 protocol adapter error

    Hi,
    Your help will be most apprecitated. Thanks in advance.
    I am tryin to connect from client (win XP) to Oracle 10g running on Linux red hat.
    I am able to successfully ping to the server bu when I do a tnsping I get the below error:
    C:\WINDOWS\system32>tnsping orcl
    TNS Ping Utility for 32-bit Windows: Version 10.1.0.4.2 - Production on 30-AUG-2
    008 17:29:10
    Copyright (c) 1997, 2003, Oracle. All rights reserved.
    Used parameter files:
    C:\DevSuiteHome_1\network\admin\sqlnet.ora
    Used TNSNAMES adapter to resolve the alias
    Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)
    (HOST = new-host.my-domain)(PORT = 1521))) (CONNECT_DATA = (SID = ORCL)))
    TNS-12560: TNS:protocol adapter error
    My listener seems to be running ok on the server
    [oracle10g@new-host ~]$ lsnrctl status
    LSNRCTL for Linux: Version 10.2.0.1.0 - Production on 30-AUG-2008 17:51:44
    Copyright (c) 1991, 2005, Oracle. All rights reserved.
    Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=ORCL)))
    STATUS of the LISTENER
    Alias listener
    Version TNSLSNR for Linux: Version 10.2.0.1.0 - Production
    Start Date 30-AUG-2008 15:48:30
    Uptime 0 days 2 hr. 3 min. 14 sec
    Trace Level off
    Security ON: Local OS Authentication
    SNMP OFF
    Listener Parameter File /oraeng/app/oracle/product/10.2.0/network/admin/listener.ora
    Listener Log File /oraeng/app/oracle/product/10.2.0/network/log/listener.log
    Listening Endpoints Summary...
    (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(KEY=ORCL)))
    (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=new-host.my-domain)(PORT=1521)))
    Services Summary...
    Service "ORCL" has 2 instance(s).
    Instance "ORCL", status UNKNOWN, has 1 handler(s) for this service...
    Instance "ORCL", status READY, has 1 handler(s) for this service...
    Service "ORCL_XPT" has 1 instance(s).
    Instance "ORCL", status READY, has 1 handler(s) for this service...
    The command completed successfully
    Also I am able to connect to the oracle from the server:
    [oracle10g@new-host ~]$ sqlplus scott/tiger@orcl
    SQL*Plus: Release 10.2.0.1.0 - Production on Sat Aug 30 17:52:52 2008
    Copyright (c) 1982, 2005, Oracle. All rights reserved.
    Connected to:
    Oracle Database 10g Enterprise Edition Release 10.2.0.1.0 - Production
    With the Partitioning, OLAP and Data Mining options

    Hi Gerard,
    I would like to gain more knowledge in this regard (oracle networking)I have some good notes on trubleshooting network issue that you may enjoy:
    http://www.dba-oracle.com/t_troubleshooting_sql_net_connectivity_errors.htm
    Hope this helps . . . .
    Donald K. Burleson
    Oracle Press author

  • Urgent!!!  ERROR: ORA-12560  TNS: protocol adapter error

    Recently we tried to install a new product with a new dataabse instance. Since doing this SQLPLUS replies with:
    ERROR: ORA-12560
    TNS: protocol adapter error
    I have looked at my tnsnames.ora and listener.ora and everything looks fine. I am hoping someone here can shed some light on this for me... Is it possible something got corrupted?
    Here is my file settings...
    # TNSNAMES.ORA Network Configuration File: C:\oracle\ora92\network\admin\tnsnames.ora
    # Generated by Oracle configuration tools.
    ORACLE9I.GESDev =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = TCP)(HOST = GESDev)(PORT = 1521))
    (CONNECT_DATA =
    (SERVER = DEDICATED)
    (SERVICE_NAME = oracle9i)
    EXTPROC_CONNECTION_DATA.GESDev =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC0))
    (CONNECT_DATA =
    (SID = PLSExtProc)
    (PRESENTATION = RO)
    INST1_HTTP.127.0.0.1 =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = TCP)(HOST = GESDev)(PORT = 1521))
    (CONNECT_DATA =
    (SERVER = SHARED)
    (SERVICE_NAME = MODOSE)
    (PRESENTATION = http://HRService)
    # LISTENER.ORA Network Configuration File: C:\oracle\ora92\network\admin\listener.ora
    # Generated by Oracle configuration tools.
    LISTENER =
    (DESCRIPTION_LIST =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = TCP)(HOST = GESDev)(PORT = 1521))
    SID_LIST_LISTENER =
    (SID_LIST =
    (SID_DESC =
    (SID_NAME = PLSExtProc)
    (ORACLE_HOME = C:\oracle\ora92)
    (PROGRAM = extproc)
    (SID_DESC =
    (GLOBAL_DBNAME = oracle9i)
    (ORACLE_HOME = C:\oracle\ora92)
    (SID_NAME = intellikit)
    # SQLNET.ORA Network Configuration File: C:\oracle\ora92\network\admin\sqlnet.ora
    # Generated by Oracle configuration tools.
    NAMES.DEFAULT_DOMAIN = GESDev
    SQLNET.AUTHENTICATION_SERVICES= (NTS)
    NAMES.DIRECTORY_PATH= (TNSNAMES, ONAMES, HOSTNAME)

    C:\>lsnrctl services
    LSNRCTL for 32-bit Windows: Version 9.2.0.1.0 - Production on 17-AUG-2006 09:30:50
    Copyright (c) 1991, 2002, Oracle Corporation. All rights reserved.
    Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=GESDev)(PORT=1521)))
    Services Summary...
    Service "PLSExtProc" has 1 instance(s).
    Instance "PLSExtProc", status UNKNOWN, has 1 handler(s) for this service...
    Handler(s):
    "DEDICATED" established:0 refused:0
    LOCAL SERVER
    Service "intellikitXDB" has 1 instance(s).
    Instance "intellikit", status READY, has 1 handler(s) for this service...
    Handler(s):
    "D000" established:0 refused:0 current:0 max:1002 state:ready
    DISPATCHER <machine: GESDEV, pid: 316>
    (ADDRESS=(PROTOCOL=tcp)(HOST=GESDev.gesldap.4point.com)(PORT=1038))
    Service "oracle9i" has 2 instance(s).
    Instance "intellikit", status UNKNOWN, has 1 handler(s) for this service...
    Handler(s):
    "DEDICATED" established:0 refused:0
    LOCAL SERVER
    Instance "intellikit", status READY, has 1 handler(s) for this service...
    Handler(s):
    "DEDICATED" established:0 refused:0 state:ready
    LOCAL SERVER
    The command completed successfully
    C:\>

  • ORA-12560 "TNS protocol adapter error":Win2k+Oracle8i_32bit.Helplessly struggling.

    Hi Oracle Guru's,
    Please save my life from this typical yet known problem.
    I got an old backup on my tapes about 3 years older. I have windows server 2k where I have an access remotely through RDP(Citrix-CuraStore).
    I installed oracle8i 32 bit on Windows 2k though it got stuck at the end where it installs optional tools(like Net8i assistant), so i closed the installation session, Because I could see Net8i assistant,dbca etc was installed on machine.
    I checked my services, found it had started the Listerner8i service.
    To create a database, I tried to happen it through DBCA...but unfortunately it gave error(ORA-12560 "TNS protocol adapter error"), I ignored it ...but it didnt move to next step...completely stuck up..So closed the session.
    I tried with ORADIM to create service, It did happen, services for database was created, I setup the environment(SID,HOME,PATH) etc.
    When I login with sqlplus , it gives again the same error(ORA-12560 "TNS protocol adapter error"), I tried many things like TCP/IP traffing disabling etc..Nothing worked.
    Can some one please help me and give me some out of box solution..I shall be really really thankful to them.
    Regards,

    Sorry, If I missed to update you back..I apologize.
    Two services(Database Service : OracleServicetest and OracleOraHome81TNSListenerLISTENER_TEST both are up...checked from SERVICES.MSC
    listener is up, I can ping the Hostname perfectly.
    Is there any other service I need to look into.
    Please find the below log as reference for TEST database.
    C:\Documents and Settings\Administrator>hostname
    srvdba02
    C:\Documents and Settings\Administrator>ping srvdba02
    Pinging srvdba02 [10.241.24.54] with 32 bytes of data:
    Reply from 10.241.24.54: bytes=32 time<10ms TTL=128
    Reply from 10.241.24.54: bytes=32 time<10ms TTL=128
    Reply from 10.241.24.54: bytes=32 time<10ms TTL=128
    Reply from 10.241.24.54: bytes=32 time<10ms TTL=128
    Ping statistics for 10.241.24.54:
        Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
    Approximate round trip times in milli-seconds:
        Minimum = 0ms, Maximum =  0ms, Average =  0ms
    C:\Documents and Settings\Administrator>
    C:\Documents and Settings\Administrator>lsnrctl status LISTENER_TEST
    LSNRCTL for 32-bit Windows: Version 8.1.7.0.0 - Production on 28-SEP-2013 23:43:01
    (c) Copyright 1998 Oracle Corporation.  All rights reserved.
    Kobler til (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=10.241.24.54)(PORT=1523)))
    STATUS FOR LYTTERPROSESS
    Tilnavn                 LISTENER_TEST
    Versjon                   TNSLSNR for 32-bit Windows: Version 8.1.7.0.0 - Production
    Startdato                 28-SEP-2013 23:19:31
    Oppetid                    0 dager 0 t. 23 min. 29 sek
    Sporingsnivσ              off
    Sikkerhet                 OFF
    SNMP                      OFF
    Lytterens parameterfil    C:\oracle\ora81\network\admin\listener.ora
    Lytterens loggfil         C:\oracle\ora81\network\log\listener_test.log
    Tjenesteoversikt...
      test          har 1 tjenestebehandler(e)
    Kommandoen ble utf°rt
    (It means test database has i service handler)..
    C:\Documents and Settings\Administrator>tnsping test
    TNS Ping Utility for 32-bit Windows: Version 8.1.7.0.0 - Production on 28-SEP-2013 23:43:17
    (c) Copyright 1997 Oracle Corporation.  All rights reserved.
    Attempting to contact (ADDRESS=(PROTOCOL=TCP)(HOST=10.241.24.54)(PORT=1523))
    Ok (10 msek)

  • ORA-12560: TNS Protocol Adapter Error(ORACLE 11g)

    i installed 11g on my laptop yesterday and it was working perfectly but today it keeps writing:(AS SHOWN BELOW)
    ========================================================================
    SQL*Plus: Release 11.2.0.1.0 Production on Fri May 20 12:26:48 2011
    Copyright (c) 1982, 2010, Oracle. All rights reserved.
    Enter user-name: hr
    Enter password:
    ERROR:
    ORA-12560: TNS:protocol adapter error
    Enter user-name: hr
    Enter password:
    ERROR:
    ORA-12560: TNS:protocol adapter error
    Enter user-name:
    ===============================================================================
    I checked the listener status and it seems to be working quite well as shown below...i don't understand!
    ================================================================================
    Microsoft Windows [Version 6.1.7600]
    Copyright (c) 2009 Microsoft Corporation. All rights reserved.
    C:\Users\Bryan>lsnrctl status
    LSNRCTL for 32-bit Windows: Version 11.2.0.1.0 - Production on 20-MAY-2011 12:31
    :07
    Copyright (c) 1991, 2010, Oracle. All rights reserved.
    Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1522)))
    STATUS of the LISTENER
    Alias LISTENER
    Version TNSLSNR for 32-bit Windows: Version 11.2.0.1.0 - Produ
    ction
    Start Date 20-MAY-2011 09:30:43
    Uptime 0 days 3 hr. 0 min. 24 sec
    Trace Level off
    Security ON: Local OS Authentication
    SNMP OFF
    Listener Parameter File C:\app\Bryan\product\11.2.0\dbhome_2\network\admin\lis
    tener.ora
    Listener Log File c:\app\bryan\diag\tnslsnr\Bryan-PC\listener\alert\log.
    xml
    Listening Endpoints Summary...
    (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC1522ipc)))
    (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=127.0.0.1)(PORT=1522)))
    Services Summary...
    Service "CLRExtProc" has 1 instance(s).
    Instance "CLRExtProc", status UNKNOWN, has 1 handler(s) for this service...
    The command completed successfully
    ===========================================================================
    i dont know wat happened PLEASE ASSIST

    Hello,
    I am having the same problem, my step son touched the computer and have no idea what he did.
    here are my results
    lsnrctl services
    Microsoft Windows [Version 6.1.7601]
    Copyright (c) 2009 Microsoft Corporation. All rights reserved.
    C:\Users\Rami>lsnrctl services
    LSNRCTL for 32-bit Windows: Version 11.2.0.2.0 - Production on 17-JAN-2013 23:22
    :23
    Copyright (c) 1991, 2010, Oracle. All rights reserved.
    Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1)))
    Services Summary...
    Service "CLRExtProc" has 1 instance(s).
    Instance "CLRExtProc", status UNKNOWN, has 1 handler(s) for this service...
    Handler(s):
    "DEDICATED" established:0 refused:0
    LOCAL SERVER
    Service "PLSExtProc" has 1 instance(s).
    Instance "PLSExtProc", status UNKNOWN, has 1 handler(s) for this service...
    Handler(s):
    "DEDICATED" established:0 refused:0
    LOCAL SERVER
    The command completed successfully
    C:\Users\Rami>

  • ORA-12560: TNS:protocol adapter error error while using BR*tools

    Hi,
    I am trying to use BRtools to display instance status (option 6 within Instance Management menu). We are running on Oracle 10g and SAP 4.6c (BRtools version 7.0 patch 13). SAP is running on Windows 2003 cluster environment.
    I checked lsnrctl status with following output..
    LSNRCTL for 64-bit Windows: Version 10.2.0.2.0 - Production on 19-FEB-200
    :06
    Copyright (c) 1991, 2005, Oracle.  All rights reserved.
    Connecting to (ADDRESS=(COMMUNITY=SAP.WORLD)(PROTOCOL=TCP)(HOST=172.20.0.
    PORT=1527))
    STATUS of the LISTENER
    Alias                     LISTENER
    Version                   TNSLSNR for 64-bit Windows: Version 10.2.0.2.0
    ction
    Start Date                07-FEB-2009 19:51:03
    Uptime                    11 days 19 hr. 42 min. 2 sec
    Trace Level               off
    Security                  ON: Local OS Authentication
    SNMP                      OFF
    Listener Parameter File   C:\oracle\PR1\102\network\admin\listener.ora
    Listener Log File         C:\oracle\PR1\102\network\log\listener.log
    Listening Endpoints Summary...
      (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=172.20.0.140)(PORT=1527)))
    The listener supports no services
    The command completed successfully
    BRspace error reads as below
    BR1001I BRSPACE 7.00 (13)
    BR1002I Start of BRSPACE processing: sdzysjut.dbw 2009-02-19 15.35.43
    BR0280I BRSPACE time stamp: 2009-02-19 15.35.44
    BR0301E SQL error -12560 at location BrDbaConnect-2
    ORA-12560: TNS:protocol adapter error
    BR0310E Connect to database instance PR1 failed
    BR0700E Fatal errors occurred - terminating processing...
    Could you please let me know if I need to make any changes to current configuration to make it work.
    I appreciate all your help,
    Thanks,
    Jitendra

    Hi Rohit,
    Here are my listener file contents
    LISTENER =
      (ADDRESS_LIST=
        (ADDRESS=
          (PROTOCOL=IPC)
          (KEY=PR1)
        (ADDRESS=
          (PROTOCOL=IPC)
          (KEY=PR1.WORLD)
        (ADDRESS=
          (COMMUNITY=SAP.WORLD)
          (PROTOCOL=TCP)
          (Host=xxx.xx.x.xxx)
          (Port=1527)
    SID_LIST_LISTENER =
      (SID_LIST=
        (SID_DESC=
          (SDU=32768)
          (SID_NAME=PR1)
          (ORACLE_HOME=C:\oracle\PR1\102)
    Fsldbprd =
      (ADDRESS_LIST=
        (ADDRESS=
          (PROTOCOL=IPC)
          (KEY=PR1)
        (ADDRESS=
          (PROTOCOL=IPC)
          (KEY=PR1.WORLD)
        (ADDRESS=
          (COMMUNITY=SAP.WORLD)
          (PROTOCOL=TCP)
          (Host=xxx.xx.x.xxx)
          (Port=1527)
    SID_LIST_Fsldbprd =
      (SID_LIST=
        (SID_DESC=
          (SDU=32768)
          (SID_NAME=PR1)
          (ORACLE_HOME=C:\oracle\PR1\102)
    TRACE_LEVEL_LISTENER = OFF
    CONNECT_TIMEOUT_LISTENER = 10
    STARTUP_WAIT_TIME_LISTENER = 0
    And here is the output of lsnrctl status command after making above changes
    STATUS of the LISTENER
    Alias                     Fsldbprd
    Version                   TNSLSNR for 64-bit Windows: Version 10.2.0.2.0 -
    ction
    Start Date                19-FEB-2009 19:39:12
    Uptime                    0 days 0 hr. 14 min. 16 sec
    Trace Level               off
    Security                  ON: Local OS Authentication
    SNMP                      OFF
    Listener Parameter File   C:\oracle\PR1\102\network\admin\listener.ora
    Listener Log File         C:\oracle\PR1\102\network\log\fsldbprd.log
    Listening Endpoints Summary...
      (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=
    .\pipe\PR1ipc)))
      (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=
    .\pipe\PR1.WORLDipc)))
      (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=xxx.xx.x.xxx)(PORT=1527)))
    Services Summary...
    Service "PR1" has 2 instance(s).
      Instance "PR1", status UNKNOWN, has 1 handler(s) for this service...
      Instance "pr1", status READY, has 1 handler(s) for this service...
    Service "PR1_XPT" has 1 instance(s).
      Instance "pr1", status READY, has 1 handler(s) for this service...
    The command completed successfully
    In Cluster admin Oracle listener name is defined as Fsldbprd.
    Please let me know if you need any additional information and thanks for looking into this issue.
    Regards,
    Jitendra
    Edited by: Jitendra Kulkarni on Feb 20, 2009 1:03 AM

  • ORA-12560: TNS:protocol adapter error rman

    hello all,
    i am on xp, and 10.2 oracle version....i created a dummy database with name comp using dbca...used FRA and took a backup though rman....i have teh backup now in FRA....
    I droped the database to do a test restore...but i cant even login to rman or sqlplus ??? i was able to login to rman before to take a backup....but now i cant.... could not figure out why...any help would be appericiated....
    C:\oracle\sql>set ORACLE_SID=comp
    C:\oracle\sql>
    C:\oracle\sql>echo %ORACLE_SID%
    comp
    C:\oracle\sql>rman target /
    Recovery Manager: Release 10.2.0.1.0 - Production on Wed Jul 6 09:54:16 2011
    Copyright (c) 1982, 2005, Oracle.  All rights reserved.
    RMAN-00571: ===========================================================
    RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
    RMAN-00571: ===========================================================
    RMAN-00554: initialization of internal recovery manager package failed
    RMAN-04005: error from target database:
    ORA-12560: TNS:protocol adapter error
    C:\oracle\sql>
    C:\oracle\sql>
    C:\oracle\sql>lsnrctl status
    LSNRCTL for 32-bit Windows: Version 10.2.0.1.0 - Production on 06-JUL-2011 09:54:20
    Copyright (c) 1991, 2005, Oracle.  All rights reserved.
    Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=xxxxxxxxx)(PORT=1521)))
    STATUS of the LISTENER
    Alias                     LISTENER
    Version                   TNSLSNR for 32-bit Windows: Version 10.2.0.1.0 - Production
    Start Date                06-JUL-2011 09:53:53
    Uptime                    0 days 0 hr. 0 min. 26 sec
    Trace Level               off
    Security                  ON: Local OS Authentication
    SNMP                      OFF
    Listener Parameter File   C:\oracle\product\10.2.0\db_1\network\admin\listener.ora
    Listener Log File         C:\oracle\product\10.2.0\db_1\network\log\listener.log
    Listening Endpoints Summary...
      (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=xxxxxxx)(PORT=1521)))
    Services Summary...
    Service "COMP" has 1 instance(s).
      Instance "COMP", status UNKNOWN, has 1 handler(s) for this service...
    The command completed successfully
    C:\oracle\sql>

    user8363520 wrote:
    hello all,
    i am on xp, and 10.2 oracle version....i created a dummy database with name comp using dbca...used FRA and took a backup though rman....i have teh backup now in FRA....
    I droped the database to do a test restore...but i cant even login to rman or sqlplus ??? i was able to login to rman before to take a backup....but now i cant.... could not figure out why...any help would be appericiated....
    If you have backup and you dropped database then you can create it again.
    1) Create directories for background,user,audit dumpdest and control,online log,datafiles.
    2) Create OracleServiceComp if that is not exists using ORADIM utility(oradim -new -sid COMP -intpwd <syspass> -pfile <pfile location>)
    3) After starting oracle service
    set ORACLE_SID=COMP
    rman target /
    /*if you do not have spfile also then you have to restore it from
    full/auto backup or startup database using pfile(create it manually)*/
    startup nomount ;
    restore controlfile from 'full or autobackup location';
    alter database mount;
    catalog start with 'backup location';
    restore database;
    recover database;
    alter database open resetlogs;

Maybe you are looking for