Headstart 6i installation - HTTP client side servers?

We are performing the headstart 6i client side install and are confused as to the client software requirements.
Is it necessary to install a HTTP listener on each client that is to be used for development. Or can we use the server based listener(Apache).
The installation document specifies the installation of WEB DB as an option and indicates that this is shipped with Designer 6i, however this does not appear to be contained within the Designer 6i CD's
Rgds, Pierre

It is not necessary to install and configure a HTTP Listener/Forms Server installation on each (developer)client. Yet it can be useful in a number of cases, for instance when your application server is Unix based.
WebDB itself is not shipped with Designer 6i, but when you install Des6i it will also install a Forms 6i runtime environment, and this will prompt you with a question whether you want to install a 'trial' version of Forms Server. The WebDB Listener service is a part of this Forms Server installation.
Kind Regards,
Peter
null

Similar Messages

ACE in one-arm model. VIP on Client Side, servers in other vlan

Hello All
i have a LAN whit many servers,but only 2 need to be balanced. So i think in one-arm model, due to the higth trafic that not be pass trought ACE.
i have a vlan 900 where is the client side and the VIP also. (10.0.9.64/26)
the servers are in vlan 503 (10.12.3.0/24)
it mi first design with ONE-arm but i thinks something is missing, because doesn't work.
the configuration is the next:
MSFC:
svclc module 1 vlan-group 1,2,
svclc vlan-group 1 503,900-902
svclc vlan-group 2 511
interface Vlan503
description OSS_&_Otros
ip address 10.12.3.253 255.255.255.0
standby 10 ip 10.12.3.254
standby 10 priority 150
standby 10 preempt delay minimum 305
interface Vlan900
description MSF_<->_ACE
ip address 10.0.9.126 255.255.255.192
end
access-list 101 permit ip 10.12.3.0 0.0.0.255 10.0.9.64 0.0.0.63
access-list 101 deny ip any any
route-map From_Server_OSS_to_ACE permit 10
match ip address 101
set ip next-hop 10.0.9.125
ACE_1/admin#
ip route 0.0.0.0 0.0.0.0 10.0.9.126
context OSS
allocate-interface vlan 511
allocate-interface vlan 900
allocate-interface vlan 902
member Max20
ACE_1/OSS# sh run
Generating configuration....
access-list EVERYONE line 10 extended permit ip any any
access-list EVERYONE line 20 extended permit icmp any any
rserver host OSS_FES_1
description OSS_Front_End_Server_1
ip address 10.12.3.140
inservice
rserver host OSS_FES_2
description OSS_Front_End_Server_2
ip address 10.12.3.150
inservice
serverfarm host SERVER_farm_OSS
rserver OSS_FES_1
inservice
rserver OSS_FES_2
inservice
class-map match-all VIP-OSS
2 match virtual-address 10.0.9.66 any
policy-map type loadbalance first-match OSS-LB-POLICY
class class-default
serverfarm SERVER_farm_OSS
policy-map multi-match OSS-POLICY-MAP
class VIP-OSS
loadbalance vip inservice
loadbalance policy OSS-LB-POLICY
loadbalance vip icmp-reply
interface vlan 900
description Clients-side
ip address 10.0.9.125 255.255.255.192
access-group input EVERYONE
access-group output EVERYONE
service-policy input OSS-POLICY-MAP
no shutdown
ip route 0.0.0.0 0.0.0.0 10.0.9.126
maybe a i need to allocate the vlan 503 in OSS Context, any advice?
Thanks in advace,
Gianni From Chile

Since you server are not behind the ACE in either bridge or routed mode add the follwoing to your config and use nat to get the traffic back to the ace.
This is how one-armed mode works.
ACE_1/OSS# sh run
Generating configuration....
access-list EVERYONE line 10 extended permit ip any any
access-list EVERYONE line 20 extended permit icmp any any
rserver host OSS_FES_1
description OSS_Front_End_Server_1
ip address 10.12.3.140
inservice
rserver host OSS_FES_2
description OSS_Front_End_Server_2
ip address 10.12.3.150
inservice
serverfarm host SERVER_farm_OSS
rserver OSS_FES_1
inservice
rserver OSS_FES_2
inservice
class-map match-all VIP-OSS
2 match virtual-address 10.0.9.66 any
policy-map type loadbalance first-match OSS-LB-POLICY
class class-default
serverfarm SERVER_farm_OSS
policy-map multi-match OSS-POLICY-MAP
class VIP-OSS
loadbalance vip inservice
loadbalance policy OSS-LB-POLICY
loadbalance vip icmp-reply
nat dynamic 10 vlan 900
interface vlan 900
description Clients-side
ip address 10.0.9.125 255.255.255.192
nat-pool 10 0.9.126 10 0.9.126 netmask 255.255.255.192 pat
access-group input EVERYONE
access-group output EVERYONE
service-policy input OSS-POLICY-MAP
no shutdown

Applet without JMF installation at client side

hello,
I am trying developing an applet SIP phone based on Jain Sip Applet Phone( which originally can only deal with audio signal). But I found a big problem that I have to make every client install the JMF, however the clients hope there is no software to be installed locally.
In application, I can run it without JMF installation by copying all the dlls to system32 directory and add some related JMF source code into my own project. Or just simply put the jmf.property to the "lib" directory, which also works.
However, as for the applet, it dosen't that simple for the security thing. Here is the output in cosole:
@mediaManager.detectSupportedCodes- number of capture devices: 2
- name of the capture device: JavaSound audio capture
- format accepted by this AUDIO device: LINEAR, 44100.0 Hz, 16-bit, Stereo, LittleEndian, Signed
- format accepted by this AUDIO device: LINEAR, 44100.0 Hz, 16-bit, Mono, LittleEndian, Signed
- format accepted by this AUDIO device: LINEAR, 22050.0 Hz, 16-bit, Stereo, LittleEndian, Signed
- format accepted by this AUDIO device: LINEAR, 22050.0 Hz, 16-bit, Mono, LittleEndian, Signed
- format accepted by this AUDIO device: LINEAR, 11025.0 Hz, 16-bit, Stereo, LittleEndian, Signed
- format accepted by this AUDIO device: LINEAR, 11025.0 Hz, 16-bit, Mono, LittleEndian, Signed
- format accepted by this AUDIO device: LINEAR, 8000.0 Hz, 16-bit, Stereo, LittleEndian, Signed
- format accepted by this AUDIO device: LINEAR, 8000.0 Hz, 16-bit, Mono, LittleEndian, Signed
- name of the capture device: vfw:Microsoft WDM Image Capture (Win32):0
- format accepted by this VIDEO device: YUV Video Format: Size = java.awt.Dimension[width=352,height=288] MaxDataLength = 202752 DataType = class [B yuvType = 32 StrideY = 704 StrideUV = 704 OffsetY = 0 OffsetU = 1 OffsetV = 3
         - format accepted by this VIDEO device: YUV Video Format: Size = java.awt.Dimension[width=160,height=120] MaxDataLength = 38400 DataType = class [B yuvType = 32 StrideY = 320 StrideUV = 320 OffsetY = 0 OffsetU = 1 OffsetV = 3
         - format accepted by this VIDEO device: YUV Video Format: Size = java.awt.Dimension[width=176,height=144] MaxDataLength = 50688 DataType = class [B yuvType = 32 StrideY = 352 StrideUV = 352 OffsetY = 0 OffsetU = 1 OffsetV = 3
         - format accepted by this VIDEO device: YUV Video Format: Size = java.awt.Dimension[width=320,height=240] MaxDataLength = 153600 DataType = class [B yuvType = 32 StrideY = 640 StrideUV = 640 OffsetY = 0 OffsetU = 1 OffsetV = 3
         - format accepted by this VIDEO device: YUV Video Format: Size = java.awt.Dimension[width=640,height=480] MaxDataLength = 614400 DataType = class [B yuvType = 32 StrideY = 1280 StrideUV = 1280 OffsetY = 0 OffsetU = 1 OffsetV = 3
java.lang.RuntimeException: No permission to capture from applets
-> Couldn't connect to audio capture device
java.lang.RuntimeException: No permission to capture from applets
-> Couldn't connect to video capture device
      I found that my applet can detect two device which is correct but has "no permission to capture from applets".
      In the progress of installation the JMF, and option is "permit recording from an applet". I read the source code, and found it dose the following works:
      if I choose "permit recording from an applet", then "allowCapture=1", and in "settingPanel.java" it dose:
     "boolean allowCapture = checkAllowCapture.getState();
      Registry.set("secure.allowCaptureFromApplets", new Boolean(allowCapture));"
      I want to do what the installation progress did to give permition to applet, however, when I do the following:
       private static final String PROP_ALLOW_CAPTURE_FROM_APPLETS
        = "secure.allowCaptureFromApplets";
       Registry.set(PROP_ALLOW_CAPTURE_FROM_APPLETS, new Boolean(true));
       Registry.commit();
      in my project , it throws exception like this: "Failed to initially commit JMFRegistry. Ignoring err.java.lang.SecurityException: commit: Permission denied"
      The code which i thought could give applet the rights is denied.
      Till now, I have also read some similar questions in different forums, but there is no good answer.
      Can you help me? Is there any possibility to run the applet without installation on the client side ? Is my method right? If not, how should I do?

xljiayuan wrote:
..I am trying developing an applet SIP phone based on Jain Sip Applet Phone( which originally can only deal with audio signal). If this is pure audio, can it be done using JavaSound?
..But I found a big problem that I have to make every client install the JMF, however the clients hope there is no software to be installed locally.To run an applet, the applet needs to be 'installed' on the user machine. Same with anything else.
BTW - have you investigated JavaFX? It is effectively the replacement for JMF, and possibly has a better end-user experience than trying to install JMF.
However, as for the applet, it dosen't that simple for the security thing. Here is the output in cosole:
in my project , it throws exception like this: "Failed to initially commit JMFRegistry. Ignoring err.java.lang.SecurityException: commit: Permission denied"Is your applet digitally signed? If not, it has no hope of intercepting sound on the client. It is that simple.
Imagine if you visited a web page with a 1px x 1px applet (effectively invisible) that could hear everything you say, and transmit it back to the server. Sun is not about to allow that, unless the end-user has granted the applet extended permissions.

Client Side Rendering on Terminal Servers

I’m having horrible printer issues on my Terminal Servers such as slow printing, slow to add printers, some applications load slowly because they are enumerating the list of printer (thanks Procmon), slow logons, etc. I'm trying to get Client Side Rendering
(CSR) disabled. From what I can tell it still appears to be on. Terminal Server are Windows Server 2008 SP2 x86.
On my print servers I have verified that all printers have Render print jobs on client computer unchecked. I have a Group Policy linked to the OU that the Terminal Servers are in that has
Always render print jobs on the server set to enabled. Per
http://blogs.technet.com/b/askperf/archive/2008/02/10/ws2008-client-side-rendering.aspx I have verified that on each Terminal Server in
HKLM\SOFTWARE\Policies\Microsoft\Windows NT\Printers the
ForceCSREMFDespooling value is present & set to 1 so the GP is being applied.
However I still have tons of entries in HKLM\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Print\Providers\Client Side Rendering Print Provider\Servers\<SERVERNAME>\Printers.
I have found KB958656 which seems to describe my problem that CSR is not being disabled. However one of the files it updates is older than a file that I have (win32spl.dll) & one is newer (printcom.dll).
Printcom.dll in hotfix is 6.0.6001.22288 mine is 6.0.6001.18000
Win32spl.dll in hotfix is 6.0.6001.22288 mine is 6.0.6002.18005
Has anyone else seen this behavior & been able to get CSR disabled?
Has anyone else had success with the KB hotfix mentioned or know whether or not installing it would causing any issues (since it has that older file)?
Thanks in an advance to any input.
Patrick Hoban
http://patrickhoban.wordpress.com

Alan/Patrick,
Hi, sorry, went away on leave for a while so didn’t respond.
Alan – our case was REG:112081612189183.
For someone who has been dealing with MS support for about 20 years, this was the most disappointing of any support call I’ve ever had raised – to have the call shut
down, without a perfmon trace, process explorer analysis, or hang dump analysis (of spooler) – and simply blame “3rd party drivers” without any proof – is utterly deplorable.
Anyway, for anyone’s benefit who has similar problems – trying to do direct printing from RDS – I’ve managed to get a solution working.
Here are the details;
A nightly print spooler clean-up script that;
Stops the spooler
Deletes the entire key under “HKLM\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Print\Providers\Client Side Rendering Print Provider”
Re-creates the key (empty) and sets the value "RemovePrintersAtLogoff"=dword:00000000
Note, this was vital.
MS support had recommended we set this to 1, along with some other keys (InactiveGuidPrinterAge,
InactiveGuidPrinterTrim) with specific values. If we used these MS support recommended values, our RDS serer would not enumerate printers for more than 3-4 hours before requiring a restart of the spooler.
Restart the spooler
Map a printer (just to make sure it works)
Clean up the USERS\.DEFAULT\Printers key on all existing servers
There was heaps of crap here, the default user NTUSER.DAT was over 800MB in size
Modify the security on the registry, using GPO to deny SYSTEM write access as below, to stop the crap writing here again;
USERS\.DEFAULT\Printers
Deny Set value
Deny Create Subkey
Run NGREGOPT on all servers to compress the DEFAULT and SOFTWARE hives back down.
Even though we had deleted the crap from “Client Side Rendering Print Provider” and the DEFAULT user hive, the registry files were still large of course, and needed to be compressed to reduce
paged pool usage.
Note, make sure no users are on the server when this is run !
With the nightly spooler ‘refresh’ and the registry security changes, we are no longer seeing any problems.
In addition the paged pool has gone down from 5GB to 1GB – which I believe was related to the registry bloat that had occurred previously.
Cleaning up the keys and using NGREGOPT has fixed this.
In addition, I am running a spooler check script every 30 minutes on each of the 13 servers.
This script checks how long it takes to enumerate the printers for the specific test user.
If it takes more than 20 seconds, we get an alert.
Since I have made the changes above, we no longer have any printing problems… touch wood.. even using HPD 5.4 for most printers, and other (RICHO) 3rd party
drivers.
If anyone wants the scripts (the spooler refresh or the check script) let me know on david.frith<at>glfconsulting.com.au
ta

How to implement a persistent HTTP connection on client side...

Sorry for the inconvenience everyone, but I could really use some help here since I am a total newbie to Java programming
I am trying to implement a persistent HTTP connection on the client side with request pipelining. The way I understand it is that client requests will be sent to the server, which will reply to them back to back, and then the client will read them accordingly. But when I read the server responses, I get only the reply for the first request, and nothing further, when I actually expect it to give me as many responses as the number of requests I ussued. Here is a sample code illustrating what I am trying to do.
====================
import java.io.*;
import java.net.*;
import java.util.*;
public class HttpClient {
public static String host = "www.somehost.com";
public static int port = 80;
public static String pathname = "/download.asp";
public static String protocol = "http";
public static ArrayList list;
public static void main(String[] args) {
Parser parser = new Parser();
list = parser.getIDs();
try {
Socket socket = new Socket(host, port);
InputStream from_server = socket.getInputStream();
PrintWriter to_server = new PrintWriter(socket.getOutputStream());
OutputStream to_file;
to_file = new FileOutputStream("HTTP_response.txt", true);
for(int i = 0; i < 3; i++)
String s = (String)parser.getIDs().get(i);
String filename = "/download.asp?id=" + s;
to_server.print("GET " + filename + "\n\n");
to_server.flush(); // Send it right now!
//This response gives only only the response to the first
//request,....
byte[] buffer = new byte[4096];
int bytes_read;
while((bytes_read = from_server.read(buffer)) != -1)
to_file.write(buffer, 0, bytes_read);
to_file.close();
socket.close();
catch (Exception e) {
System.err.println(e);
System.err.println("Usage: java HttpClient <URL> [<filename>]");
}

There are many things wrong with your code. Learn the HTTP protocol and you'll know what I mean.
Here's a hint - you'r missing headers in your code.
Some servers do not support keep-alive connections, nor do you request a keep-alive connection.
Connection: keep-alive
Use that header field and see what happends. Also, in your while-loop, you actually close the output file and the socket. Don't you think it may be hard for the server to respond to a client that closed the connection on it?
1. You don't know HTTP
2. You don't seem to know Java
3. You don't seem to understand basic programming logic

How to get and put data in HTTP header in Client Side

One JSP's function is to display data records page by page. Client users could click "First page" or "Previous Page" or "Next Page" or "Last Page" button to let the JSP to show the corresponding page. So the JSP must remember the current page number. Due to there are a number of client users maybe access the JSP at the same time, keep the current page number in session, there will be a lot of session is created at the same time, this will impact system's performance. So using session to keep data method is not used. I plan to use request header and response header to pass the current page number. I know use the response.addHeader to put data in response header and also know use request.getHeader to get data in request header in server side, but I donot know how to put data in request header and how to get data in response header in client side. Could you please give me a help? If donot use these method, are there any other method? Thanks a lot.

Why not pass it as a parameter with the URL?
at the beginning of the page..
<%
int pageNumber = Integer.parseInt(request.getParameter("page"));
%>
then when defining your links
<a href="thisPage.jsp?page=<%= (pageNumber-1)%>">Previous</a>
<a href="thisPage.jsp?page=<%= (pageNumber+1)%>">Next</a>

How To Update A Table View From Client Side !!!!

Hi I would like to update a table view from the Client Side. So that the user can keep updating the relevent data on the client and when they have finally finished they can press Save so the entire page is then sent to the Server.
Does anyone know how to do this, I guess u have to use the EPCM, I have just started on it and would really appreciate some Help.
Thanks,
Emmanuel.

This is what I found :-
There are a couple of ways to approach this.
1) load the excel spreadsheet into the database "as is". You can use interMedia
text to convert the .xls file into a .htm file (HTML) or use iFS (see
http://technet.oracle.com/
for
more info on that) to parse it as well. InterMedia text will convert your XLS
spreadsheet into a big HTML table (easy to parse out what you need at that
point)
2) Using OLE automation, a program you write can interact with Excel, request
data from a spreadsheet, and insert it. Oracle Forms is capable of doing this
for example as is other languages environments. In this fashion, you can remove
the "manual" and "sqlldr" parts -- your program can automatically insert the
data.
3) You can write a VB script that uses ODBC or Oracle Objects for OLE (OO4O) in
Excel. This VB script would be able to put selected data from the spreadsheet
into the database. We would recommend OO4O. It provides an In-Process COM
Automation Server that provides a set of COM Automation interfaces/objects for
connecting to Oracle database servers, executing queries and managing the
results. OO4O is available from
http://technet.oracle.com

The Group Policy client-side extension Scripts failed ...

This is an error I've been seeing forever and it was always the impression that upgrading would resolve it, but it never has even in 10.3. 100% of our users get these errors in the Event Viewer:
Event Type: Error
Event Source: Userenv
Event Category: None
Event ID: 1085
Date: 10/21/2010
Time: 8:04:52 AM
User: NT AUTHORITY\SYSTEM
Computer: XXXXXX
Description:
The Group Policy client-side extension Scripts failed to execute. Please look for any errors reported earlier by that extension.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
We also seem to have flakey policy issues where once in awhile a user will not be able to logon to Windows with Workstation Only while getting the " not allowed to logon interactively" message, other times the users report not being able to access the Windows Date and Time Properties and further sometimes they are unable to make system changes.
We have troubleshooted this and the only resolutions we've found are to run zac cc, zac ref, zac pl and sometimes it seems like deleting c:\windows\system32\grouppolicy will help.
In regards to the Event Viewer entry I posted, on any given machine I can issue the command gpupdate and it will put another entry into the Event Viewer (sometimes multiple ones). I've learned through research that if I "clean up" c:\windows\system32\grouppolicy\gpt.ini the errors go away, but once the policy is refreshed they come right back.
This is the version ZenWorks gives the users:
[General]
gPCFunctionalityVersion=2
gPCFunctionalityVersion=2
gPCMachineExtensionNames=[{35378EAC-683F-11D2-A89A-00C04FBBCFA2}{0F6B957D-509E-11D1-A7CC-0000F87571E3}][{3610EDA5-77EF-11D2-8DC5-00C04FA31A66}{0F6B957D-509E-11D1-A7CC-0000F87571E3}][{42B5FAAE-6536-11D2-AE5A-0000F87571E3}{40B6664F-4972-11D1-A7CA-0000F87571E3}][{4CFB60C1-FAA6-47F1-89AA-0B18730C9FD3}{0F6B957D-509E-11D1-A7CC-0000F87571E3}][{827D319E-6EAC-11D2-A4EA-00C04F79F83A}{803E14A0-B4FB-11D0-A0D0-00A0C90F574B}]
Version=6488106
gPCUserExtensionNames=[{35378EAC-683F-11D2-A89A-00C04FBBCFA2}{0F6B957E-509E-11D1-A7CC-0000F87571E3}][{42B5FAAE-6536-11D2-AE5A-0000F87571E3}{40B66650-4972-11D1-A7CA-0000F87571E3}][{4CFB60C1-FAA6-47F1-89AA-0B18730C9FD3}{0F6B957E-509E-11D1-A7CC-0000F87571E3}][{A2E30F80-D7DE-11D2-BBDE-00C04F86AE3B}{FC715823-C5FB-11D1-9EEF-00A0C90347FF}]
This is the version I cleaned up:
[General]
gPCFunctionalityVersion=2
gPCUserExtensionNames=[{35378EAC-683F-11D2-A89A-00C04FBBCFA2}{0F6B957E-509E-11D1-A7CC-0000F87571E3}][{4CFB60C1-FAA6-47F1-89AA-0B18730C9FD3}{0F6B957E-509E-11D1-A7CC-0000F87571E3}][{A2E30F80-D7DE-11D2-BBDE-00C04F86AE3B}{FC715823-C5FB-11D1-9EEF-00A0C90347FF}]
gPCUserExtensionNames=[{35378EAC-683F-11D2-A89A-00C04FBBCFA2}{0F6B957E-509E-11D1-A7CC-0000F87571E3}][{A2E30F80-D7DE-11D2-BBDE-00C04F86AE3B}{FC715823-C5FB-11D1-9EEF-00A0C90347FF}]
I'm not sure how to get Zenworks to use the cleaned up version nor and I too sure what those extra extensions are and how they got in there. I may need to contact Novell in regards to this, but since I'm already working on an SR with them I figured I'd go ahead and post here first.
Any help or advice would be greatly appreciated.

Here are the groups I'm using. NOTE: These have been in affect throughout the issues experienced. Users will work perfectly fine then suddenly the problem will start happening without any policy change on our side.
-Member of-
Network Configuration Operators+
Remote Desktop Users+
Users+
-Assigned Rights under a group I called "Other Rights"-
Access this computer from network
Change the system time
Log on locally
Shut down the system
The only condition I have is that these issues happen when logging in Workstation Only and I'm not able to recreate the problem on demand with tests.
Originally Posted by craig_wilson
The "Interactive Logon" is a Windows Security Permission.
It is generally assigned to certain local groups such as "User".
Which groups are assigned this right can be changed manually and
controlled by local security policies.
When user's get this error, it generally means their account is not in a
local group that has been assigned that right.
If using "DLU", make sure the user accounts are a member of "Users".
And If anyone was messing with security policies, make sure they did not
take away "Interactive Logons" from anyone.
On 10/29/2010 7:06 AM, jcsmith1 wrote:
>
> Thanks for replying craig.
>
> My policy woes have only grown since my first post. We are currently
> testing the removal of administrative rights and now we're having
> teleworkers (who login Workstation Only) getting the message "policy
> does not allow interactive login". What -seems- to fix it is a zac cc,
> zac ref and zac pl, however we just started getting call backs from
> users.
>
> I seem to have no further leads and Novell's ZenWorks tech supports
> seems to be going through some kind of painful-to-the-customer
> transition as one of my thoughts on resolving the issue is to go to 10.3
> or 10.3.1, but my Satellites appear to be upgrading but in reality do
> not upgrade (but the primary servers upgraded) (See SR 10655976331).
>
> Does anyone knows how to troubleshoot policy issues when the users
> aren't loggin into ZCM?
>
> craig_wilson;2036646 Wrote:
>> See: 'Group Policy Error: The Group Policy client-side extension Script
>> failed to execute.'
>> (Group Policy Error: The Group Policy client-side extension Script failed to execute.)
>>
>> This would never be fixed in any patch, since it would be the job of
>> GPEDIT to properly maintain the GPT.INI.
>>
>> Most of the Time these errors are cosmetic and caused by stray script
>> extensions.
>>
>> You may want to create an Enhancement Request to allow the creation of
>> "Filters" so certain errors are discarded and not sent to the DB/ZCC.
>> This way an Admin could choose to filter out various error messages
>> that
>> they deem are not actually of concern.
>>
>> On 10/21/2010 9:36 AM, jcsmith1 wrote:
>>>
>>> This is an error I've been seeing forever and it was always the
>>> impression that upgrading would resolve it, but it never has even in
>>> 10.3. 100% of our users get these errors in the Event Viewer:
>>>
>>> -Event Type: Error
>>> Event Source: Userenv
>>> Event Category: None
>>> Event ID: 1085
>>> Date: 10/21/2010
>>> Time: 8:04:52 AM
>>> User: NT AUTHORITY\SYSTEM
>>> Computer: XXXXXX
>>> Description:
>>> The Group Policy client-side extension Scripts failed to execute.
>>> Please look for any errors reported earlier by that extension.
>>>
>>> For more information, see Help and Support Center at
>>> http://go.microsoft.com/fwlink/events.asp.
>>> -
>>> We also seem to have flakey policy issues where once in awhile a
>> user
>>> will not be able to logon to Windows with Workstation Only while
>> getting
>>> the " not allowed to logon interactively" message, other times the
>> users
>>> report not being able to access the Windows Date and Time Properties
>> and
>>> further sometimes they are unable to make system changes.
>>>
>>> We have troubleshooted this and the only resolutions we've found are
>> to
>>> run zac cc, zac ref, zac pl and sometimes it seems like deleting
>>> c:\windows\system32\grouppolicy will help.
>>>
>>> In regards to the Event Viewer entry I posted, on any given machine
>> I
>>> can issue the command gpupdate and it will put another entry into
>> the
>>> Event Viewer (sometimes multiple ones). I've learned through
>> research
>>> that if I "clean up" c:\windows\system32\grouppolicy\gpt.ini the
>> errors
>>> go away, but once the policy is refreshed they come right back.
>>>
>>> This is the version ZenWorks gives the users:
>>>> [General]
>>>> gPCFunctionalityVersion=2
>>>> gPCFunctionalityVersion=2
>>>>
>> gPCMachineExtensionNames=[{35378EAC-683F-11D2-A89A-00C04FBBCFA2}{0F6B957D-509E-11D1-A7CC-0000F87571E3}][{3610EDA5-77EF-11D2-8DC5-00C04FA31A66}{0F6B957D-509E-11D1-A7CC-0000F87571E3}][{42B5FAAE-6536-11D2-AE5A-0000F87571E3}{40B6664F-4972-11D1-A7CA-0000F87571E3}][{4CFB60C1-FAA6-47F1-89AA-0B18730C9FD3}{0F6B957D-509E-11D1-A7CC-0000F87571E3}][{827D319E-6EAC-11D2-A4EA-00C04F79F83A}{803E14A0-B4FB-11D0-A0D0-00A0C90F574B}]
>>>> Version=6488106
>>>>
>> gPCUserExtensionNames=[{35378EAC-683F-11D2-A89A-00C04FBBCFA2}{0F6B957E-509E-11D1-A7CC-0000F87571E3}][{42B5FAAE-6536-11D2-AE5A-0000F87571E3}{40B66650-4972-11D1-A7CA-0000F87571E3}][{4CFB60C1-FAA6-47F1-89AA-0B18730C9FD3}{0F6B957E-509E-11D1-A7CC-0000F87571E3}][{A2E30F80-D7DE-11D2-BBDE-00C04F86AE3B}{FC715823-C5FB-11D1-9EEF-00A0C90347FF}]
>>>>
>>>>
>>>
>>> This is the version I cleaned up:
>>>> [General]
>>>> gPCFunctionalityVersion=2
>>>>
>> gPCUserExtensionNames=[{35378EAC-683F-11D2-A89A-00C04FBBCFA2}{0F6B957E-509E-11D1-A7CC-0000F87571E3}][{4CFB60C1-FAA6-47F1-89AA-0B18730C9FD3}{0F6B957E-509E-11D1-A7CC-0000F87571E3}][{A2E30F80-D7DE-11D2-BBDE-00C04F86AE3B}{FC715823-C5FB-11D1-9EEF-00A0C90347FF}]
>>>>
>> gPCUserExtensionNames=[{35378EAC-683F-11D2-A89A-00C04FBBCFA2}{0F6B957E-509E-11D1-A7CC-0000F87571E3}][{A2E30F80-D7DE-11D2-BBDE-00C04F86AE3B}{FC715823-C5FB-11D1-9EEF-00A0C90347FF}]
>>>>
>>>>
>>>
>>> I'm not sure how to get Zenworks to use the cleaned up version nor
>> and
>>> I too sure what those extra extensions are and how they got in there.
>> I
>>> may need to contact Novell in regards to this, but since I'm already
>>> working on an SR with them I figured I'd go ahead and post here
>> first.
>>>
>>> Any help or advice would be greatly appreciated.
>>>
>>>
>>
>>
>> --
>> Craig Wilson - MCNE, MCSE, CCNA
>> Novell Knowledge Partner
>>
>> Novell does not officially monitor these forums.
>>
>> Suggestions/Opinions/Statements made by me are solely my own.
>> These thoughts may not be shared by either Novell or any rational
>> human.
>
>
Craig Wilson - MCNE, MCSE, CCNA
Novell Knowledge Partner
Novell does not officially monitor these forums.
Suggestions/Opinions/Statements made by me are solely my own.
These thoughts may not be shared by either Novell or any rational human.

Steps to upgrade Client Side Xe with apex3.2.1

Hi,
I want to upgrade client side xe with apex3.2.1.Please help me to do this.
can you send me any llink with step by step installation of apex3.2.1 over client xe.
Thanks & Regards
Manoj

Hi manoj;
Please follow below and see its helpful for your issue, i belive you will find your answer in those links
http://blogs.oracle.com/SanthoshK/2008/09/oracle_xe_apex_3x_installation.html
Installation of APEX 3.2 on Oracle 10G Database
http://apps2fusion.com/at/kr/384-apex
Regard
Helios

RMI client side callbacks

Hi all,
I have an RMI server and a number of clients that run on different machines. What I need to do is, implement the "observer" pattern. i.e.
in my case, not only the clients call the server, but also the server
must notify the registered clients when its state changes.
For that purpose, I suppose, that my clients must also be RMI servers.
My first question is, is that true what I suppose? Is there any other
way to implement asynchron client side callbacks with RMI?
My second question is, if it must be done so (clients are also RMI servers), how can I implement this? Server needs client interface jar
file, ans client needs server interface jar file at compile time.
(Important: I do not use any HTTP server from which I can load _Stub
classes at runtime)
I don't like this architecture at all and therefore think that there
may be better solutions. One solution may be to poll the state of the
server from the clients periodically, so that there is no need for
callbacks. But that is also not the perfect solution for me.
Can someone suggest anything else?
Any idea will be greatly appreciated!
Thank you

Hello guvener
Some time ago, I did exactly what you are thinking about. Here was the strategy.
1. There was a server program, sitting (obviously) on the server machine, where rmiserver was running. The server class had only a single public method for the calling routines to call.
2. That public method took, as a parameter, a transaction request. One possible transaction was, "Here is a message for another client." Another possible transaction was, "Listen out for a message for me." For example, a client would call the server with the "listen" transaction or with a "here's a message" transaction.
3. When the calling method requested a "listen" transaction, the server would enter a "wait" state until it received a message for that particular client.
4. To prevent blocking, there were three specific strategies:
(a) The client would call the server with a "listen" transaction in a separate thread.
(b) There was a "cancel" transaction that would allow a client to cancel its "listen" transaction with the server.
(c) There was a "close-down" transaction that would allow the server to tell the clients their "listen" transactions had been cancelled, as it was closing down.
This requires thorough and careful planning. However, once the classes are correctly planned, this strategy is elegant and simple and leads to only a small amount of coding. It's also flexible, without any restrictions on how many transactions a client could request at a time.
Do be careful to synchronize where applicable!
I hope this helps.

HTTP Client, URL Encoding

Hi there, got a bit of a problem here and hoping that someone might have an idea.
2 servers, Web AS 6.20 SP45 (Java and ABAP) same Kernel releases, DB releases, patch levels, components and everything.
Same program (transported from one to the other)
Code sample can be found <a href="/people/sap.user72/blog/2004/11/04/bof-teched-munich-04--rss-http-and-bsp
I make a simple HTTP client and I send out a URL.
In the URL I have a parameter:
?content=#X|SID|NUM|DESCRIPTION
From System A it works and the Apache server on the other side picks up the URL as
?content=%23X%7SID%7NUM%7DESCRIPTION
If I do it from System B the Apache server on the other side picks up the URL as
?content=#X|SID|NUM|DESCRIPTION
I have gone through all my parameters, settings, etc but I can't seem to find something that is different or would cause this.
Here is my last hope BEFORE going to the OSS, any takers? any ideas??

Not exactly a why this is happening, but the following might be a work around. Have you tried performing the URL Escaping on your URL before sending it to the HTTP Client. You can do so with cl_http_utility=>escape_url.
data: output_url type string,
input_url type string.
input_url = `?content=#X|SID|NUM|DESCRIPTION`.
write: / input_url.
output_url = cl_http_utility=>escape_url( input_url ).
write: / output_url.

Solution for tnsnames at client side

Hi,
My database is in oracle 10.2.0. I have configured 2 standby servers for my primary database. I want to know that are there any parameter in tnsnames.ora at the client side so that If switchover or failover occurs,the client or user should not be aware of the switch process i.e., without down time.
Because there will be different service names and host, how can this be addressed at the client tnsnames.ora.
Thanks in advance for your suggestions,
satyanag

Hi Satyanag,
It's possible to specify more than one address location. For example:
SCR9 =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = bloo)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = fermat)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = scr9)
If the first address can't be contacted Oracle will try the second address.
Cheers,
Andy Barry
http://www.shutdownabort.com

Having problem with client side Authentication.

Hi,
I am haveing a problem enabling client side authentication with SSL on
weblogic 5.1.
I have set up the .properties files as explained, however it appears
my client is not sending a certificate back to the server. The same
client however works perfectly (using the same keystore file) with a
sample ClassFileSErver webserver from the jsse distribution. (the
client is a very slightly modified version of
SSLSocketClientWithClientAuth sample that comes with Jsse)
Below I've included a section of the debug dump from the interactions.
The only other difference I can see is the cipher suites offered by
the servers.
Weblogic offers type 0 or 9, and agrees on type 9
(SSL_RSA_WITH_DES_CBC_SHA), whereas ClassFileServer offer type 0 or 5
and settles on type 5 (SSL_RSA_WITH_RC4_128_SHA).
I am using the same keystore for both examples. Both servers request
an RSA client cert.... I'm out of ideas.
Any help would be greatfully received.
Cheers,
Keith
Debug dump information
=====================================
1/Weblogic server.
*** CertificateRequest
Cert Types: RSA,
Cert Authorities:
<CN=K H, OU=itsmobile, O=itsmobile, L=Dublin, ST=Dublin, C=ie>
<[email protected], CN=Demo Certificate Authority,
OU=Security, O=BEA WebLogic, L=San Francisco, ST=California, C=US>
<CN=Thawte Test CA Root, OU=TEST TEST TEST, O=Thawte Certification,
ST=FOR TESTING PURPOSES ONLY, C=ZA>
[read] MD5 and SHA1 hashes: len = 427
0000: 0D 00 01 A7 01 01 01 A3 00 67 30 65 31 0B 30 09
.........g0e1.0.
0010: 06 03 55 04 06 13 02 69 65 31 0F 30 0D 06 03 55
..U....ie1.0...U
0020: 04 08 13 06 44 75 62 6C 69 6E 31 0F 30 0D 06 03
....Dublin1.0...
0030: 55 04 07 13 06 44 75 62 6C 69 6E 31 12 30 10 06
U....Dublin1.0..
0040: 03 55 04 0A 13 09 69 74 73 6D 6F 62 69 6C 65 31
.U....itsmobile1
0050: 12 30 10 06 03 55 04 0B 13 09 69 74 73 6D 6F 62
.0...U....itsmob
0060: 69 6C 65 31 0C 30 0A 06 03 55 04 03 13 03 4B 20
ile1.0...U....K
0070: 48 00 AC 30 81 A9 31 0B 30 09 06 03 55 04 06 13
H..0..1.0...U...
0080: 02 55 53 31 13 30 11 06 03 55 04 08 13 0A 43 61
.US1.0...U....Ca
0090: 6C 69 66 6F 72 6E 69 61 31 16 30 14 06 03 55 04
lifornia1.0...U.
00A0: 07 13 0D 53 61 6E 20 46 72 61 6E 63 69 73 63 6F ...San
Francisco
00B0: 31 15 30 13 06 03 55 04 0A 13 0C 42 45 41 20 57
1.0...U....BEA W
00C0: 65 62 4C 6F 67 69 63 31 11 30 0F 06 03 55 04 0B
ebLogic1.0...U..
00D0: 13 08 53 65 63 75 72 69 74 79 31 23 30 21 06 03
..Security1#0!..
00E0: 55 04 03 13 1A 44 65 6D 6F 20 43 65 72 74 69 66 U....Demo
Certif
00F0: 69 63 61 74 65 20 41 75 74 68 6F 72 69 74 79 31 icate
Authority1
0100: 1E 30 1C 06 09 2A 86 48 86 F7 0D 01 09 01 16 0F
.0...*.H........
0110: 73 75 70 70 6F 72 74 40 62 65 61 2E 63 6F 6D 00
[email protected].
0120: 8A 30 81 87 31 0B 30 09 06 03 55 04 06 13 02 5A
.0..1.0...U....Z
0130: 41 31 22 30 20 06 03 55 04 08 13 19 46 4F 52 20 A1"0
..U....FOR
0140: 54 45 53 54 49 4E 47 20 50 55 52 50 4F 53 45 53 TESTING
PURPOSES
0150: 20 4F 4E 4C 59 31 1D 30 1B 06 03 55 04 0A 13 14
ONLY1.0...U....
0160: 54 68 61 77 74 65 20 43 65 72 74 69 66 69 63 61 Thawte
Certifica
0170: 74 69 6F 6E 31 17 30 15 06 03 55 04 0B 13 0E 54
tion1.0...U....T
0180: 45 53 54 20 54 45 53 54 20 54 45 53 54 31 1C 30 EST TEST
TEST1.0
0190: 1A 06 03 55 04 03 13 13 54 68 61 77 74 65 20 54
...U....Thawte T
01A0: 65 73 74 20 43 41 20 52 6F 6F 74 est CA Root
main, READ: SSL v3.0 Handshake, length = 4
*** ServerHelloDone
[read] MD5 and SHA1 hashes: len = 4
0000: 0E 00 00 00 ....
main, SEND SSL v3.0 ALERT: warning, description = no_certificate
main, WRITE: SSL v3.0 Alert, length = 2
And below is a sample when I used the ClassFileServer.
This time the client (same src) returned a certificate.
2/ClassFileSErver (from Sun Jsse distribution)
*** CertificateRequest
Cert Types: DSS, RSA,
Cert Authorities:
<CN=K H, OU=itsmobile, O=itsmobile, L=Dublin, ST=Dublin, C=ie>
[read] MD5 and SHA1 hashes: len = 114
0000: 0D 00 00 6E 02 02 01 00 69 00 67 30 65 31 0B 30
...n....i.g0e1.0
0010: 09 06 03 55 04 06 13 02 69 65 31 0F 30 0D 06 03
...U....ie1.0...
0020: 55 04 08 13 06 44 75 62 6C 69 6E 31 0F 30 0D 06
U....Dublin1.0..
0030: 03 55 04 07 13 06 44 75 62 6C 69 6E 31 12 30 10
.U....Dublin1.0.
0040: 06 03 55 04 0A 13 09 69 74 73 6D 6F 62 69 6C 65
..U....itsmobile
0050: 31 12 30 10 06 03 55 04 0B 13 09 69 74 73 6D 6F
1.0...U....itsmo
0060: 62 69 6C 65 31 0C 30 0A 06 03 55 04 03 13 03 4B
bile1.0...U....K
0070: 20 48 H
*** ServerHelloDone
[read] MD5 and SHA1 hashes: len = 4
0000: 0E 00 00 00 ....
matching client alias : rsakey
*** Certificate chain

Matt,
Did you read this article:
https://wiki.sdn.sap.com/wiki/display/BSP/Using%20Proxies
This explains how to properly setup the HTTPURLLOC table.
In your case you should have entries that look something like this:
40 HTTP * <internal host name> <https port>
50 HTTPS * <external host name> <https port>
In addition you need to run the report to determine if the proxy configuration is setup properly. The URL should be run with the
https://<externalhostname>/sap/bc/bsp/sap/system_test/test_proxy.htm
Take care,
Stephen

Installation sccm client on workgroup client in DMZ

Hi Guys,
i tried to install the sccm client on workgroup clients in a DMZ environment.
First I created a client certifikate for the workgroup client on the sccm server and installed the certifikate on the workgroup computer with certutil.exe.
commandline for installation:
ccmsetup.exe /usePKICert /NOCRLCheck SMSMP=servername.bla.com SMSSITECODE=BLA
i get this errors in the ccmsetup.log:
Unexpected row count (0) retrieved from AD.
Failed to get site version from AD with error 0x80004005
thanks for your support,
Chris

Refer these Pls
http://eskonr.com/2013/08/sccm-configmgr-2012-manage-workgroup-computers-for-deploymentremote-tools-etc/ (An Excellent article)
Client installation in DMZ step by step :
http://myitforum.com/cs2/blogs/cstauffer/archive/2009/02/06/sccm-client-install-in-a-dmz.aspx
http://blogs.technet.com/b/keithmayer/archive/2012/07/30/planning-system-center-configuration-manager-across-dmz-and-protected-subnets-sysctr-configmgr.aspx
http://nikifoster.wordpress.com/2011/01/31/installing-configmgr-clients-on-servers-in-a-dmz/
Thanks, Prabha G

Generate PDF from VC without using BI-JAVA or PDF convertor on client side

Hi there
I need to generate a PDF from Visual Composer
a pdf final result, generated by several BAPIS, several tables , logo, static text, etc
but I do not want to use the two solutions below described.
I want to use a component or something installed on the server, to facilitate user's life.
Is there any PDF convertor in R3? I have to install an Adobe Component? other idea?
a. In this thread ilustrates how to generate a PDF in a very simple way using a print function
and a PDF convertor previously installed.
Re: How to export from VC a bapi output table to a PDF file
b. I have read another solution that uses the PCD location of the Web Analizar (BI-Java).
Thanks, Alex Market

Again, NO BI-JAVA. NO PDF convertor on client side.
My idea is to create a Flex component with the PDF convert library.
Something like this,
http://lucamezzalira.com/2009/02/28/create-pdf-in-runtime-with-actionscript-3-alivepdf-zinc-or-air-flex-or-flash/
Then embed it to the Visual Composer
like Amir Mimran show us in this "How to guide"
Re: NEW: Flash Component Consumption in Visual Composer 7.01 SP5
The problem that I see is
our installation is 7.0 SP18, we have to upgrade to 7.01 SP5 at least,
the Flash Components feature is available on 7.01 SP5 (NetWeaver 2004s Enhancement Pack 1, SP5)
and more important, currently, this functionaily is only available in Windows Platform.
Unix flatform will be supported from ehp1 sp6, according to this post
VC model including flash component is not visible in run-time.
regards, Alex

Headstart 6i installation - HTTP client side servers?

Similar Messages

Maybe you are looking for