Help! Can't overclock E4300 w/"pad mod" on G965M-FI!

Well, it looks like I have the same problem with the G965M-FI as those with the 965 Neo and Platinum.
According to the sticky post "About MSI 965 Neo and Platinum: FACTS", I have the same problem. I tried the pin mod (or pad mod) where BSEL1 is connected to VSS thinking this should work on any motherboard. No luck, 200x9 every time. Finally, I got the bright idea to try clearing CMOS. Once I did that, it booted up with this message:
4300 @ 1.80GHz ,Speed: 267x9
A 200MHz system bus processor is installed. This processor is not supported on this system board, and will run at reduced processor clock speed. System performance will be impacted.
Do you wish to continue to boot at 267MHz system bus and reduced processor speed? (Y/N)
Press Y to continue or press N to shutdown.
Is there any way around this? Any hack? Any BIOS mod? I'm guessing not because it would have been in the sticky...
Ok, so assuming the answer to all my questions above is NO, the 2nd motherboard I was considering was an MSI 945GM3. Does that motherboard support the pad mod?

Wow, from all the replies I am getting, I guess this card is an excellent overclocker.....

Similar Messages

Help: can't overclock Q9300 - MSI P7N SLI Platinum !

I tryed everything, i just can't overclock Q9300...way ?. tryed alle beta bios..please help !!
Overclock only to 340 makes PC freeze
MSI P7N-SLI PLATINUM nForce 750i SLI
Intel Core 2 Quad Q9300 2.5GHz 6MB FSB1333
Arctic Freezer 7 Pro socket 775
Corsair DDR2 PC2-800 2GB CL4 kit XMS2 * 2 = 4 GB
Samsung Spinpoint T166 320GB 16MB 7200RPM SATAII
Asus GeForce PCI-E 8800GT 512MB
Antec Sonata 3 Earthwatt 500Watt HD + eSata front
All bios here i have tryed, but no luck:
http://forums.hardwarezone.com.sg/showpost.php?p=27386192&postcount=5
Somebody had luck to overclock Q9300 on P7N-SLI Platinum ? please post info

Try with mem settings auto and only adjust Vdimm to vendorspecs.
Did you try BIOS V1.1 from MSI : http://global.msi.com.tw/index.php?func=downloaddetail&type=bios&maincat_no=1&prod_no=1373
This did solve some memory issues.
If so try, if you can, QVL memory and see if problem persists.
Hope this helps , good luck and keep us posted
Also be sure that your on manual and not linked, this will give problems too, when fsb divider gets higher then memory divider.
Furthermore, by using non qvl mem, the NB and fsb vtt are very depending on eachother.
I had the same with my board , the only difference with yours is the cirque pipe cooling and an extra chip for yorkfield support , but it is do-able

Help: Can't start up in Safe Mode!

I'm trying to fire up in Safe Mode to do a few Spotlight housekeeping tasks but my Mac won't have it. When I try start up Safe it gets no further than the Grey Apple Logo and spinning wheel. After a short while the fans spin up to full speed and nothing else happens. I have to force the Mac to shut down and I can then start up again normally.
Any help on this would be much appreciated as there may come a time when I NEED to start up in Safe Mode.
Thanks in advance. Derek.

Hi-
Might want to try a Single User mode boot (command +s) and run fsck.
-Startup in Single User mode.
-At the command-line prompt, type */sbin/fsck -fy*. Press Return.
fsck will go through five "phases" and then return information about your disk's use and fragmentation. Once it finishes, it'll display this message if no issue is found:
The volume (nameofvolume) appears to be OK
-If fsck found issues and has altered, repaired, or fixed anything, it will display this message:
FILE SYSTEM WAS MODIFIED
Important: If this message appears, repeat the fsck command again, until fsck tells you that your volume appears to be OK (first-pass repairs may uncover additional issues, so this is a normal thing to do).
-When fsck reports that your volume is OK, type reboot at the prompt and then press Return.
-Your computer should start up normally and allow you to log in.
After this, try a Safe mode boot, again.
Resolve startup issues and perform disk maintenance with Disk Utility and fsck

Help, can't overclock after bios update!

On the stock k9n2 750a bios version, my AMD 5400 OC’ed to a stable 3.08ghz without any hassle by simply setting the FSB to 220mhz . Recently, I flashed to the AMI 7374 v3.5 bios and couldn’t even post after bumping the FSB to 202mhz (it’s fine @200mhz). So, I reverted the bios back to AMI 7374 v3.1 and for some reason it now can’t post either after saving a FSB above 200mhz . As far as I can remember, I’m using the same settings as I used when I got the stable 220mhz FSB.
Anyone know what the bios update did to kill my overclocking or got some ideas/advice on how to get back to the stable 220mhz FSB? Thanks.

Quote from: JLio01 on 29-January-15, 13:54:12
What does ME version show under BIOS currently? When you check the ratio under OS, do you put your system under loading? And did you re-install driver from website after updating BIOS?
http://www.msi.com/support/mb/Z68AGD65_G3.html#support_download
ME version 8.1.2.1318. Even if I put the system at 100% load in Windows, the processor never moves past 3.4 GHz. I've checked this in multiple programs (CPUZ, RealTemp, TMonitor, etc.) And yes, I reinstalled the drivers that were listed under the BIOS update.
Quote from: TZBC on 29-January-15, 14:17:52
Go to OC section and change to advanced mode, change your CPU Ratio Mode from Dynamic to Fixed mode.
And go to windows checking the ratio have changed or not.
EDIT: sorry, I forgot this motherboard doesn't have this settings, try Disabled or Enable "Adjust CPU Ratio in OS"
I've tried changing that setting (Adjust CPU Ratio in OS) but it doesn't seem to have any effect.
However, I just noticed that I didn't have the newest version of CPUZ. I updated it and now it shows more detailed information for the multiplier: x34 (16-44)
So it is detecting that I have set it to 44 in Windows after all. But it seems to be indicating that it's using a dynamic CPU ratio of 16-44 - which I don't want, I want it fixed at 44 - but as you say, there's no option for dynamic/fixed on my motherboard. However, on the old v23.7 BIOS, if I set it to 44 it stayed at 44 always.
Even if it's using a dynamic ratio for some reason, it's not doing that right either because it's still never moving past 3.4 GHz (nor is it ever dropping below 3.4 GHz).

CAN PHOTOSMART 5510 WORK IN BOTH MODES-USB AND WIRELESS TO PRINT FROM I-PAD OR I-PHONE 4S.

CAN PHOTOSMART 5510 WORK IN BOTH MODES-USB AND WIRELESS TO PRINT FROM I-PAD OR I-PHONE 4S.

SEPPLES86,
In order to print from your I-Pad or I-Phone you would need to be connected through wireless. Air Print works when your printer and device ( ipad or iphone) is connected to the same WI-FI network.
Here is a link to a post with a lot of good information concerning Air Print.
http://h30434.www3.hp.com/t5/ePrint-Print-Apps-Mobile/AirPrint-how-to-use-Apple-s-AirPrint-solution-...
If I helped you at all it would be great if you clicked the blue kudos star!
If I solved your post please mark it as solved to help others.
I'm a printer tech with HP.

HT1363 My old iPod Nano says to use iTunes to restore and I've followed all suggested help steps, but I can't get it into disk mode nor can I get it to show in my computer or in iTunes.

My old iPod Nano says to use iTunes to restore and I've followed all suggested help steps, but I can't get it into disk mode nor can I get it to show in my computer or in iTunes. I have the latest version of iTunes. Windows has all the most recent updates too. I can reset the iPod, but the message to Use iTunes to restore comes back and I am stuck.

Already tried another USB port, still nothing.
I don't have another PC to check, I only have one which is the one not working with my iPod.
It appears under my Computer, just not under iTunes. Plus, the iPod classic troubleshooting assistant doesn't work because I can't restore since it can't come up onto my iTunes! Even my iPod says "Use iTunes to Restore" once in a while, but I plug it in & I'm not able to restore it since it won't come up under iTunes.
Please help

Can only start up in Safe Mode, please help!

Hi friends, I need your help!
I woke up this morning and my iMac G5 (w/ Leopard) was frozen. I restarted it manually, but it would freeze on a blue screen without loading the OS. It can start up fine in safe mode, but that's it! I've tried repairing permissions and zapping the PRAM - any other ideas?
What can I do in Safe Mode that might fix my comp? I haven't recently installed any applications, and I have all "open at login" items turned off.
Thanks for your help!
Ellis

Are you able to start with your install disc? If so, use Disk Utility
1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
3. Click the First Aid tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Click Repair. Disk Utility checks and repairs the disk.
You might also try running Preferential Treatment to see if you have corrupt preferences.
Please let us know how you get on,

HT3986 Can anyone help me to get the Tack pad drivers for windows 7 on mAcBook Air..

Can anyone help me to get the Tack pad drivers for windows 7 on mAcBook Air..

If you've created the Windows 7 Drivers CD/USB drive, using Boot Camp Assistant in OSX, the drivers should be on there. My MacBook Pro (2010) touchpad works fine with those drivers installed, and I think it's identical to the Air's.
http://support.apple.com/kb/HT4407 for info on how to create this drive.

Help me My iPhone is in recovery mode and I do not see it on my laptop and on iTunes. Moreover, I can not turn it off and when I try it comes up all the time in the recovery mode.

help me
My iPhone is in recovery mode and I do not see it on my laptop and on iTunes. Moreover, I can not turn it off and when I try it comes up all the time in the recovery mode.

Hey Yan Heng,
Thanks for the question. It sounds like your iOS device is not recognized in iTunes for Windows, while in recovery mode. The following resource may help to resolve your issue. While you should run through each step, the specific information related to your symptom is outlined in Step 5 (If the device is not recognized while in Recovery Mode).
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Thanks,
Matt M.

Plz tell me how I can get back from the recovery mode to my normal mode without lossing data ... actually I was trying to update ios 7 in my 4s so then mobile stuck into recovery mode...plz help?

plz tell me how I can get back from the recovery mode to my normal mode without lossining data...I stuck in this mode while I was try to update ios 7 in my 4s

If it's in recovery mode, anything on the phone is already gone. Restore the phone using iTunes, then restore it from your last backup. If you've been backing up on a regular basis as intended, you won't lose anything except what's changed since the last backup.

On my iPhone 4 I can play music through the speaker or headphones, but I can not get audio in phone mode, I can't hear anything nor can anyone hear me! Help. Please.

On my iPhone 4 I can play music through the speaker or headphones, but I can not get audio in phone mode! I can hear anything through the ear piece or via a headphone. Nor can people hear me when I call. I must be doing something wrong, but what?

Hello Angela,
Thank you for the details of the issue you are experiencing with sound on your iPhone. I recommend the following steps for an issue like this:
Verify that the volume is set to a level you would normally be able to hear.
Ensure that there is nothing plugged in to the headset jack or the dock connector.
If the iPhone is in a protective case, make sure that the speaker port isn't blocked by the case.
Make sure that the speaker and dock port aren't clogged with debris. If necessary, clean it with a clean, small, dry, soft-bristled brush. Carefully and gently brush away any debris.
If an audio issue occurs when using a specific application, try testing other applications to see if the issue persists.
If the iPhone is paired with a Bluetooth headset or car kit:
Try turning off Bluetooth.
If you experience difficulties with the Bluetooth feature, followthese troubleshooting steps.
Restart the iPhone.
If restarting doesn't fix the issue, ensure that your iPhone is updated to the latest version of iOS.
If the issue is not resolved after restoring the iPhone software, please contact Apple Support.
You can find the full article here:
iPhone: No sound or distorted sound from speaker
http://support.apple.com/kb/ts5180
Thank you for using Apple Support Communities.
Best,
Sheila M.

I jailbroke my ipod and its in recovery mode i cant take it out of it and i cant restore becasue i changes host to sariks sever i need help can any one help me

i cant take it out of it and i cant restore becasue i changes host to sariks sever i need help can any one help me please please i just got my ipod i realy need help

Sorry, due to the Terms of Use, problems with jailbroken devices can't be discussed here.

Can't view data in browse mode.

I have a database of about 50 records I can view the data in list mode but when I switch to Browse the page turns grey. I trashed the preferences but no improvement.
Any help?

Hello
- 1 - AppleWorks will NOT be updated. It will be replaced by iWork.
- 2 - If you wish, you may attach your file to a mail and send it to:
koenig then a dot then yvan then an @ then tele2 then a dot then fr
If you do, I will be able to look if the file is working well on another machine.
So you will know if the oddity is to be searched in your machine itself.
Yvan KOENIG (from FRANCE mercredi 21 décembre 2005 9:12:42)

Can't Run program in Debug Mode

To: [email protected]
cc:
Subject: Can't Run program in Debug Mode
Has anyone else experienced this problem? We have written a non-express
program that uses the Express generated services project as a supplier
plan. However, when we try running this program in debug mode about 50%
(or more) of the time we abend while Forte is trying to partition the
application. Since we have many database classes in our Business Model we
are wondering if Forte is timing out during the partition phase or if the
server partition is running out of memory . The following error messages
are produced by Forte. Any suggestions???
=======================
Error messages on client:
=======================
SYSTEM ERROR: Unable to start the partition testacadprogoffer_CL0_Part1 on
any
of the nodes to which it has been assigned. See the remainder of the
error
stack for more information.
Class: qqsp_ResourceException
Error #: [1602, 593]
Detected at: qqcf_StandardConfig::LoadRemotePartition at 5
Last TOOL statement: method overview.StartApplication
Error Time: Tue Dec 02 12:56:01
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
SYSTEM ERROR: Unable to start partition testacadprogoffer_CL0_Part1 on node
admin2.
Class: qqsp_ErrorDescriptor
Error #: [1602, 592]
Detected at: qqcf_StandardConfig::LoadRemotePartition at 3
Error Time: Tue Dec 02 12:56:01
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
SYSTEM ERROR: Lost contact with remote server while trying to load
partition
testacadprogoffer_CL0_Part1. Check server log file for more information
about
the specific problem.
Class: qqsp_ResourceException
Error #: [1301, 102]
Detected at: qqem_IPartitionAgent::Startup at 5
Error Time: Tue Dec 02 12:56:01
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
INFORMATION: The connection to the partner was terminated by the
Communication
Manager for the reasons below.
Class: qqsp_DistAccessException
Detected at: qqdo_PartitionMgr::StopLocation at 1
Error Time: Tue Dec 02 12:56:00
Distributed method called: qqrt_ForteExecAgentProxy.LoadPartition!6
(object name Unnamed) from partition "Forte_Executor", (partitionId =
F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9, taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9.229]) in application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment CentralEnv
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
INFORMATION: Network partner closed connection. This usually means the
process at the other end of the wire failed. Please go look there and
find
out why.
Class: qqsp_DistAccessException
Detected at: qqcm_HoseFSM::ReceivedClose at 2
Error Time: Tue Dec 02 12:56:00
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
INFORMATION: Received close: Connection aborted (10053).
Class: qqsp_DistAccessException
Detected at: qqcm_HoseFSM::ReceivedClose at 1
Error Time: Tue Dec 02 12:56:00
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
=======================
Log messages on server:
=======================
Attached to manager for node admin2.
aud Tue Dec 2 09:34:36 : Loading partition testacadprogoffer_cl0_Part2
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 09:41:58 : Shutting down partition as requested.
aud Tue Dec 2 09:41:59 : Unloaded partition testacadprogoffer_cl0_Part2.
aud Tue Dec 2 09:49:44 : Loading partition testacadprogoffer_cl0_Part2
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 10:00:11 : Shutting down partition as requested.
aud Tue Dec 2 10:00:12 : Unloaded partition testacadprogoffer_cl0_Part2.
aud Tue Dec 2 10:18:34 : Loading partition testacadprogoffer_cl0_Part3
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 10:27:00 : Shutting down partition as requested.
aud Tue Dec 2 10:27:00 : Unloaded partition testacadprogoffer_cl0_Part3.
aud Tue Dec 2 10:47:03 : Loading partition
EvaluateApplRequirementsBO_CL0_Part1 built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 11:09:26 : Shutting down partition due to failure of agent
owner's partition.
aud Tue Dec 2 11:09:26 : Shutting down partition as requested.
aud Tue Dec 2 11:09:26 : Unloaded partition
EvaluateApplRequirementsBO_CL0_Part1.
aud Tue Dec 2 12:36:14 : Loading partition testacadprogoffer_CL0_Part1
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 12:45:17 : Shutting down partition as requested.
aud Tue Dec 2 12:45:17 : Unloaded partition testacadprogoffer_CL0_Part1.
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
Task 11: qqcm_HoseRecvServiceTask::Run: Caught unexpected exception
FATAL ERROR: ************* Out of Memory, requested (1K) available (0K)
Class: qqsp_ResourceException with ReasonCode: SP_ER_OUTOFMEMORY
Detected at: qqos_MemoryManager
Error Time: Tue Dec 2 12:49:01
Exception occurred (locally) on partition "Forte_Executor",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10f3, t
askId = [F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10f3.11]) in application
"Forte Runtime", pid 14020 on node admin2 in environ
ment CentralEnv.
FATAL ERROR: ************* Out of Memory, requested (1K) available (0K)
Class: qqsp_ResourceException with ReasonCode: SP_ER_OUTOFMEMORY
Detected at: qqos_MemoryManager
Error Time: Tue Dec 2 12:48:57
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
ERROR: TMgr.RunThread: task cm.Recv failed terminating.
Probably caused by a FATAL exception.
David Wilbur email: [email protected]
University of Windsor phone: 519-253-3000 ext. 2779
Windsor, Ontario Canada
-----------------------------------------------

Hi,
We have had the same problem in a non-express application
with a heavy server partition. In our case, the error was not
systematic, depending on the server workload at the time we
tried to partition and run.
The work-around we're using is to put the -fm flags (increasing the x
parameter to say 30000) in the 'server arguments' of your server
partition
properties in the partition workshop. Note that if your server is a Unix
platform,
you need to put double-quotes before and after the parenthesis in the -fm
syntax.
Hope this helps,
Vincent Figari
BTW, what Forte version are you using ?
On Tue, 2 Dec 1997 13:44:24 -0500 "David Wilbur"<[email protected]>
writes:
>
>
>
>
>
To: [email protected]
cc:
Subject: Can't Run program in Debug Mode
Has anyone else experienced this problem? We have written a
non-express
program that uses the Express generated services project as a supplier
plan. However, when we try running this program in debug mode about
50%
(or more) of the time we abend while Forte is trying to partition the
application. Since we have many database classes in our Business
Model we
are wondering if Forte is timing out during the partition phase or if
the
server partition is running out of memory . The following error
messages
are produced by Forte. Any suggestions???
=======================
Error messages on client:
=======================
SYSTEM ERROR: Unable to start the partition
testacadprogoffer_CL0_Part1 on
any
of the nodes to which it has been assigned. See the remainder of
the
error
stack for more information.
Class: qqsp_ResourceException
Error #: [1602, 593]
Detected at: qqcf_StandardConfig::LoadRemotePartition at 5
Last TOOL statement: method overview.StartApplication
Error Time: Tue Dec 02 12:56:01
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in
application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
SYSTEM ERROR: Unable to start partition testacadprogoffer_CL0_Part1 on
node
admin2.
Class: qqsp_ErrorDescriptor
Error #: [1602, 592]
Detected at: qqcf_StandardConfig::LoadRemotePartition at 3
Error Time: Tue Dec 02 12:56:01
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in
application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
SYSTEM ERROR: Lost contact with remote server while trying to load
partition
testacadprogoffer_CL0_Part1. Check server log file for more
information
about
the specific problem.
Class: qqsp_ResourceException
Error #: [1301, 102]
Detected at: qqem_IPartitionAgent::Startup at 5
Error Time: Tue Dec 02 12:56:01
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in
application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
INFORMATION: The connection to the partner was terminated by the
Communication
Manager for the reasons below.
Class: qqsp_DistAccessException
Detected at: qqdo_PartitionMgr::StopLocation at 1
Error Time: Tue Dec 02 12:56:00
Distributed method called:
qqrt_ForteExecAgentProxy.LoadPartition!6
(object name Unnamed) from partition "Forte_Executor",
(partitionId =
F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9, taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9.229]) in
application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in
application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
INFORMATION: Network partner closed connection. This usually means
the
process at the other end of the wire failed. Please go look there
and
find
out why.
Class: qqsp_DistAccessException
Detected at: qqcm_HoseFSM::ReceivedClose at 2
Error Time: Tue Dec 02 12:56:00
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in
application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
INFORMATION: Received close: Connection aborted (10053).
Class: qqsp_DistAccessException
Detected at: qqcm_HoseFSM::ReceivedClose at 1
Error Time: Tue Dec 02 12:56:00
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in
application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
=======================
Log messages on server:
=======================
Attached to manager for node admin2.
aud Tue Dec 2 09:34:36 : Loading partition
testacadprogoffer_cl0_Part2
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 09:41:58 : Shutting down partition as requested.
aud Tue Dec 2 09:41:59 : Unloaded partition
testacadprogoffer_cl0_Part2.
aud Tue Dec 2 09:49:44 : Loading partition
testacadprogoffer_cl0_Part2
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 10:00:11 : Shutting down partition as requested.
aud Tue Dec 2 10:00:12 : Unloaded partition
testacadprogoffer_cl0_Part2.
aud Tue Dec 2 10:18:34 : Loading partition
testacadprogoffer_cl0_Part3
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 10:27:00 : Shutting down partition as requested.
aud Tue Dec 2 10:27:00 : Unloaded partition
testacadprogoffer_cl0_Part3.
aud Tue Dec 2 10:47:03 : Loading partition
EvaluateApplRequirementsBO_CL0_Part1 built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 11:09:26 : Shutting down partition due to failure of
agent
owner's partition.
aud Tue Dec 2 11:09:26 : Shutting down partition as requested.
aud Tue Dec 2 11:09:26 : Unloaded partition
EvaluateApplRequirementsBO_CL0_Part1.
aud Tue Dec 2 12:36:14 : Loading partition
testacadprogoffer_CL0_Part1
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 12:45:17 : Shutting down partition as requested.
aud Tue Dec 2 12:45:17 : Unloaded partition
testacadprogoffer_CL0_Part1.
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
Task 11: qqcm_HoseRecvServiceTask::Run: Caught unexpected exception
FATAL ERROR: ************* Out of Memory, requested (1K) available
(0K)
Class: qqsp_ResourceException with ReasonCode: SP_ER_OUTOFMEMORY
Detected at: qqos_MemoryManager
Error Time: Tue Dec 2 12:49:01
Exception occurred (locally) on partition "Forte_Executor",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10f3, t
askId = [F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10f3.11]) in
application
"Forte Runtime", pid 14020 on node admin2 in environ
ment CentralEnv.
FATAL ERROR: ************* Out of Memory, requested (1K) available
(0K)
Class: qqsp_ResourceException with ReasonCode:
SP_ER_OUTOFMEMORY
Detected at: qqos_MemoryManager
Error Time: Tue Dec 2 12:48:57
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
ERROR: TMgr.RunThread: task cm.Recv failed terminating.
Probably caused by a FATAL exception.
David Wilbur email: [email protected]
University of Windsor phone: 519-253-3000 ext. 2779
Windsor, Ontario Canada

I updated the system on my I pad yesterday. Now I can not start my I pad. The screen is black, if I hold the button on the right side, first the Apple logo starts, than immediately the I-tunes Logo with a "Plug" sign comes up. That stays on for ever. What

I updated my I pad yesterday with the ISO 7.04 . Now it just has a black screen. When I hold the button on the right hand down for 10 seconds, I first very briefly get the Apple Logo, than immediately the I-Tunes sign with a plug sign. I cannot get anything else working. I did not have I-tunes on my i-pad since the file is large, but have it on my MAC . So how can I get my I-pad working again????

This solved all my problems. It took a while, about 87 minutes for the complete "restore to factory setting" and after that about 30 minutes to put all my contacts etc. back on.
It did'nt matter how long it took, I have my I-Pad back and that is great.
I really do appreciate your help. Thank you so much.

Help! Can't overclock E4300 w/"pad mod" on G965M-FI!

Similar Messages

Maybe you are looking for